TY - JOUR A1 - Nicolicea, Alberto A1 - Oliveros-Mata, E. S. A1 - Zabila, Y. A1 - Makarov, D. A1 - Melzer, Michael A1 - Pelkner, Matthias T1 - Flexible anisotropic magnetoresistive sensors for novel magnetic flux leakage testing capabilities N2 - Rigid magnetic field sensors such as anisot Hall sensors have been used for years and have become industry standard for electromagnetic non-destructive testing (NDT). Recent technological developments in the field of flexible electronics allow for the fabrication of reshapeable magnetic field sensors on flexible substrates via thin-film deposition or printing. The magnetic properties of these sensors have comparable characteristics to industry-standard rigid magnetic field sensors, with the added ability of adapting to the surface of complex components and scanning in contact with the sample surface. This improves defect detectability and magnetic signal strength by minimizing the scanning lift-off (LO) distance. In this article flexible AMR sensors mounted on a rotative mechanical holder were used to scan a semi-circular ferromagnetic sample with 3 reference defects via magnetic flux leakage (MFL) testing, thus demonstrating the applicability of this type of sensors for the scanning of curved samples. In order to benchmark the performance of these sensors in comparison to industry standard rigid magnetic field sensors, a ferromagnetic sample with 10 reference defects of different depths was scanned employing flexible AMR and rigid GMR sensors. Defects with depths ranging from 110 μm up to 2240 μm were detected with an signal-tonoise ratio (SNR) of 2.7 up to 27.9 (for flexible AMR sensors) and 6.2 up to 72.3 (for rigid GMR sensors), respectively. A 2D magnetometer mapping of the sample with a spatial scanning step of 10 × 50 μm2 (flexible AMR) and 16 × 100 μm2 (rigid GMR) was obtained. The results show that this type of sensor can be used for high-resolution and high-detail mapping of defects on the surface of planar and non-planar ferromagnetic samples since the scanning lift-off distance is equal to the substrate thickness of 20 μm for in-contact scanning. The SNR comparison between flexible and rigid sensors shows that the performance of the flexible AMR sensors employed is not very far behind the performance of the rigid GMR sensors used. KW - Flexible magnetic field sensors KW - Non-destructive testing KW - Magnetic flux leakage KW - Thin film sensor fabrication KW - Defect detection PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-603931 DO - https://doi.org/10.1016/j.ndteint.2024.103160 SN - 0963-8695 VL - 146 SP - 1 EP - 15 PB - Elsevier CY - Amsterdam AN - OPUS4-60393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nicolicea, Alberto A1 - Oliveros-Mata, E. S. A1 - Makarov, D. A1 - Melzer, Michael A1 - Pelkner, Matthias T1 - Flexible anisotropic magnetoresistive sensors for novel eddy current testing applications N2 - The standard method for eddy current testing (ET) of conductive materials relies on using rigid coils. In recent years magnetoresistive (MR) sensors in combination with an excitation wire have become a promising candidate for this application since it would increase the spatial resolution. New developments in flexible electronics have enabled the production of flexible sensors with the novel capability of scanning samples in conformal contact with the surface. In this article flexible anisotropic magnetoresistive (AMR) sensors were used in combination with a thin induction wire to perform eddy current testing of a curved aluminum sample with several defects imprinted on its surface. To benchmark the performance of this new method, a flat sample with reference defects of various dimensions was also scanned using flexible AMR sensors, inductive coils and rigid giant magnetoresistive (GMR) sensors. The results show that this new method of using flexible magnetic field sensors coupled with an excitation wire can easily be applied to the scanning of curved samples, while in the benchmark test employing the flat sample, the performance is not far behind more conventional techniques, with defects with depths down to 30 μm and widths down to 400 μm being detectable with an SNR of 3 (signal magnitude) and 8 (signal phase shift) at the excitation frequency of 50 kHz, and defects with depths down to 30 μm and widths down to 600 μm being detectable with an SNR of 10 (signal magnitude) and 17 (signal phase shift) at 260 kHz. KW - Magnetic field sensors KW - Flexible magnetic field sensors KW - Flexible electronics KW - Non-destructive testing KW - Eddy current testing KW - Thin film sensor fabrication KW - Defect detection KW - Magnetism PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634325 DO - https://doi.org/10.1016/j.measurement.2025.117340 SN - 1873-412X VL - 253, Part A SP - 1 EP - 15 PB - Elsevier CY - Amsterdam AN - OPUS4-63432 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nicolicea, Alberto T1 - Flexible magnetoresistive sensors for novel electromagnetic testing capabilities N2 - Doctoral seminar showing the results obtained in the first year of research. The initial prototype for the scanning of a flat ferromagnetic sample with flexible magnetic sensors is presented, together with a quick introduction to anisotropic magnetoresistive sensors and their fabrication process. T2 - BAM Doktorandenseminar - Department 8 CY - Berlin, Germany DA - 11.05.2023 KW - Magnetic Sensors KW - Non-destructive Testing KW - Magnetic Flux Leakage Testing KW - Flexible Magnetoresistive Sensors KW - Defect Detection PY - 2023 AN - OPUS4-62682 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nicolicea, Alberto T1 - Flexible magnetoresistive sensors for novel electromagnetic testing capabilities N2 - Doctoral seminar presentation showing the results obtained in the second year of research. Besides the results shown in the previous doctoral seminar, eddy current testing and the scanning of curved surfaces is now included. T2 - BAM Doktorandenseminar - Department 8 CY - Berlin, Germany DA - 26.09.2024 KW - Flexible Magnetoresistive Sensors KW - Non-destructive Testing KW - Magnetic Flux Leakage Testing KW - Eddy Current Testing KW - Defect Detection PY - 2024 AN - OPUS4-62683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fricke, F. A1 - Brandalero, M. A1 - Liehr, Sascha A1 - Kern, Simon A1 - Meyer, Klas A1 - Kowarik, Stefan A1 - Hierzegger, R. A1 - Westerdick, S. A1 - Maiwald, Michael A1 - Hübner, M. T1 - Artificial Intelligence for Mass Spectrometry and Nuclear Magnetic Resonance Spectroscopy Using a Novel Data Augmentation Method N2 - Mass Spectrometry (MS) and Nuclear Magnetic Resonance Spectroscopy (NMR) are valuable analytical and quality control methods for most industrial chemical processes as they provide information on the concentrations of individual compounds and by-products. These processes are traditionally carried out manually and by a specialist, which takes a substantial amount of time and prevents their utilization for real-time closed-loop process control. This paper presents recent advances from two projects that use Artificial Neural Networks (ANNs) to address the challenges of automation and performance-efficient realizations of MS and NMR. In the first part, a complete toolchain has been realized to develop simulated spectra and train ANNs to identify compounds in MS. In the second part, a limited number of experimental NMR spectra have been augmented by simulated spectra, to train an ANN with better prediction performance and speed than state-of-the-art analysis. These results suggest that, in the context of the digital transformation of the process industry, we are now on the threshold of a strongly simplified use of MS and MRS and the accompanying data evaluation by machine-supported procedures, and can utilize both methods much wider for reaction and process monitoring or quality control. KW - Industry 4.0 KW - Cyber-Physical Systems KW - Artificial Neural Networks KW - Mass Spectrometry KW - Nuclear Magnetic Resonance Spectroscopy KW - Modular Production PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-539412 UR - https://ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=9638378 DO - https://doi.org/10.1109/TETC.2021.3131371 SN - 2168-6750 VL - 10 IS - 1 SP - 87 EP - 98 PB - IEEE AN - OPUS4-53941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Integrated and Networked Systems and Processes – A Perspective for Digital Transformation in (Bio) Process Engineering N2 - The competitiveness of the process industry is based on ensuring the required product quality while making optimum use of equipment, raw materials and energy. Chemical companies have to find new paths to survive successfully in a changing environment, while also finding more flexible ways of product and process development to bring their products to market more quickly – especially high-quality high-end products like fine chemicals or pharmaceuticals. The potential of digital technologies belongs to these. One way is knowledge-based production, taking into account all essential equipment, process and regulatory data of plants and laboratories. Today, the potential of this data is often not yet consistently used for a comprehensive understanding of production. Another approach uses flexible and modular chemical plants, which can produce different high-quality products using multi-purpose equipment with short downtimes between campaigns and reduce the time to market of new products. Digital transformation is enabling completely new production concepts that are being used increasingly. Intensified continuous production plants also allow for difficult to produce compounds. This contribution aims to encourage a more holistic approach to the digitalization and use of machine-assisted methods in (bio) process engineering by introduction of integrated and networked systems and processes, which have the potential to speed up the high-quality production of specialty chemicals and pharmaceuticals. T2 - 6th BioProScale Symposium - industrial scale bioprocess intensification from process development to large-scale understanding CY - Online meeting DA - 29.03.2021 KW - Industry 4.0 KW - Biotechnology KW - Bio engineering KW - Process Analytical Technology KW - BioProScale KW - Artificial Neural Networks PY - 2021 UR - https://biotechnologie.ifgb.de/node/648 AN - OPUS4-52371 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Modular process control with compact NMR spectroscopy – From field integration to automated data analysis N2 - Chemical and pharmaceutical companies have to find new paths to survive successfully in a changing environment, while also finding more flexible ways of product and process development to bring their products to market more quickly – especially high-quality high-end products like fine chemicals or pharmaceuticals. A current approach uses flexible and modular chemical production units, which can produce different high-quality products using multi-purpose equipment with short downtimes between campaigns and reduce the time to market of new products. NMR spectroscopy appeared as excellent online analytical tool and allowed a modular data analysis approach, which even served as reliable reference method for further Process Analytical Technology (PAT) applications. Using the available datasets, a second data analysis approach based on artificial neural networks (ANN) was evaluated. Therefore, amount of data was augmented to be sufficient for training. The results show comparable performance, while improving the calculation time tremendously. In future, such fully integrated and interconnecting “smart” systems and processes can increase the efficiency of the production of specialty chemicals and pharmaceuticals. T2 - GIDRM Day (Gruppo Italiano Discussione Risonanze Magnetiche) - Data analysis and NMR: from fundamental aspects to health and material applications CY - Online meeting DA - 14.10.2022 KW - Process Control KW - Online NMR Spectroscopy KW - Industry 4.0 KW - Process Analytical Technology KW - Data Analysis KW - Machine-Assisted Workflows PY - 2022 DO - https://doi.org/http://www.gidrm.org/index.php/activities/workshops/2022-workshops/gidrm-day-data-analysis-and-nmr-from-fundamental-aspects-to-health-and-material-applications AN - OPUS4-56002 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Modular process control with compact NMR spectroscopy: From field integration to fully automated data analysis N2 - Chemical and pharmaceutical companies need to find new ways to survive successfully in a changing environment, while finding more flexible ways of product and process development to bring their products to market faster - especially high-value, high-end products such as fine chemicals or pharmaceuticals. This is complicated by changes in value chains along a potential circular economy. One current approach is flexible and modular chemical production units that use multi-purpose equipment to produce various high-value products with short downtimes between campaigns and can shorten time-to-market for new products. Online NMR spectroscopy will play an important role for plant automation and quality control, as the method brings very high linearity, matrix independence and thus works almost calibration-free. Moreover, these properties ideally enable automated and machine-aided data analysis for the above-mentioned applications. Using examples, this presentation will outline a possible more holistic approach to digitalization and the use of machine-based processes in the production of specialty chemicals and pharmaceuticals through the introduction of integrated and networked systems and processes. T2 - Benchtop NMR: From Academia to Industry CY - Online meeting DA - 28.09.2022 KW - Digital Transformatioin KW - Process Industry KW - Benchtop NMR Spectroscopy KW - Procee Analytical Technology KW - Modular Production KW - Specialty Chemicals KW - Industry 4.0 PY - 2022 UR - https://eventos.fct.unl.pt/benchtop_nmr_workshop2022/pages/welcome AN - OPUS4-55850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Curoșu, Iurie A1 - Balzani, Daniel A1 - Freitag, Steffen A1 - Neu, Gerrit Emanuel A1 - Niederleithinger, Ernst A1 - Simon, Sven A1 - Weber, Sebastian T1 - Methoden zur Bewertung abgebauter Stahlbetonelemente für deren Wiederverwendung N2 - Ziel des neu eingerichteten SFB 1683 „Interaktionsmethoden zur modularen Wiederverwendung von Bestandstragwerken“ ist es, die Wiederverwendung von Betonbauteilen auf strukturellem Niveau zu erforschen und dazu grundlagenwissenschaftliche Methoden zu entwickeln. Es wird die Idee verfolgt, Bestandstragwerke planmäßig im Rückbau zu Modulen zu dekonstruieren, statt diese unkontrolliert abzubrechen. Hierfür müssen die Module in ihren Eigenschaften charakterisiert, aufgearbeitet, ggf. instand gesetzt oder verstärkt und baukastenartig zu neuen Tragwerken zusammengefügt werden. Die gesamte Prozesskette wird über die geplante Laufzeit des SFBs auf der Ebene der Teilprojekte (TP), Projektgruppen und Interaktionsketten (IK) systematisch und kollaborativ erforscht. Die in diesem Aufsatz präsentierte IK „Beherrschung der Unschärfe“ fokussiert sich auf die Entwicklung und Erprobung von experimentellen, numerischen und datengetriebenen Methoden und Strategien für eine umfassende, aber dennoch schnelle und zerstörungsfreie Charakterisierung der abgebauten Elemente. Auf dieser Basis werden Dauerhaftigkeits‐ und Tragfähigkeitsmodelle entwickelt, die die Prognose der Restnutzungsdauer unter verschiedenen Einwirkungen zuverlässig und unter Berücksichtigung der multiplen Unschärfen ermöglichen. Dieser Aufsatz stellt die Ziele, die Interaktionen sowie die Methoden der beteiligten TP zusammenfassend vor. KW - Stahlbeton KW - Wiedernutzung KW - Bewertung KW - Zerstörungsfreie Prüfung PY - 2025 DO - https://doi.org/10.1002/bate.70002 SN - 0932-8351 VL - 102 IS - 8 SP - 483 EP - 492 PB - Ernst & Sohn GmbH AN - OPUS4-64016 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Melzer, Michael T1 - The temperature DCC exposed N2 - The DAkkS-accredited calibration laboratory of the German Federal Institute for Materials Research and Testing (BAM) has established valid XML digital calibration certificates (DCCs) for calibrations of resistance thermometers within the scope of its accreditation. Hence, all necessary information according to ISO/IEC 17025 and the DKD-R 5-1 calibration rule is provided in a machine-readable and machine-interpretable form. Furthermore, we actively participate in the definition of general and community-specific good practice requirements for the DCC of temperature quantities as technical specifications, hosted by the German Calibration Service (DKD). In this contribution the entire XML source code of a DCC from a Pt 100 thermometer calibration will be exposed and discussed. The DCC was automatically generated using a self-implemented middleware that is compiling the metadata (i.e. customer-, order-, item- and method data) and combines it with the measured calibration data and influence conditions into a process- and lab-specific DCC template. Since it was issued as an accredited calibration certificate, the validated and authorized DCC is also equipped with the novel digital accreditation symbol to form an `eAttestation´. This advanced electronic seal with a qualified certificate was recently piloted with the German national accreditation body (DAkkS), and, after successful validation by the receiver, verifies the active accreditation status of the issuing body at the time of sealing (authorization). As it also provides all other functionalities of an electronic seal, (i.e. data integrity and authenticity), it can fully replace a digital signature on accredited DCCs. The presented temperature DCC architecture fully complies to the latest good practice definitions of the DKD and thus represents a level 4 DCC according to the utility model for machine interpretability of DCCs. This also includes basic and quantity-specific refType definitions that are linked to an online refType repository to harmonize these key semantic providing elements across other DCC-issuing laboratories. The work was performed within the national QI-Digital initiative of the German Federal Ministry for Economic Affairs and Climate Action. T2 - Deutsche Marktüberwachungskonferenz 2025 CY - Berlin, Germany DA - 17.09.2025 KW - Calibration KW - Digital Calibration Certificate KW - E-Attestation KW - Digital Metrology KW - QI-Digital PY - 2024 AN - OPUS4-64147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Melzer, Michael T1 - The digital accreditation symbol: verified trust in digital certificates N2 - This presentation provides a brief overview of the digital accreditation symbol, which is available for DAkkS-accredited bodies to proof their active accreditation on digital reports and certificates (eAttestations). The basic functionality, application and automatic verifycation is presented on PDF and XML based eAttestations. T2 - International Metrology Congress (CIM) 2025 CY - Lyon, France DA - 11.03.2025 KW - Akkreditation KW - Digital Calibration Certificate KW - E-Attestation KW - Digital Certificates KW - QI-Digital PY - 2025 AN - OPUS4-64174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Melzer, Michael T1 - The temperature DCC exposed N2 - The DAkkS-accredited calibration laboratory of the German Federal Institute for Materials Research and Testing (BAM) has established valid XML digital calibration certificates (DCCs) for calibrations of resistance thermometers within the scope of its accreditation. Hence, all necessary information according to ISO/IEC 17025 and the DKD-R 5-1 calibration rule is provided in a machine-readable and machine-interpretable form. Furthermore, we actively participate in the definition of general and community-specific good practice requirements for the DCC of temperature quantities as technical specifications, hosted by the German Calibration Service (DKD). In this contribution the entire XML source code of a DCC from a Pt 100 thermometer calibration will be exposed and discussed. The DCC was automatically generated using a self-implemented middleware that is compiling the metadata (i.e. customer-, order-, item- and method data) and combines it with the measured calibration data and influence conditions into a process- and lab-specific DCC template. Since it was issued as an accredited calibration certificate, the validated and authorized DCC is also equipped with the novel digital accreditation symbol to form an `eAttestation´. This advanced electronic seal with a qualified certificate was recently piloted with the German national accreditation body (DAkkS), and, after successful validation by the receiver, verifies the active accreditation status of the issuing body at the time of sealing (authorization). As it also provides all other functionalities of an electronic seal, (i.e. data integrity and authenticity), it can fully replace a digital signature on accredited DCCs. The presented temperature DCC architecture fully complies to the latest good practice definitions of the DKD and thus represents a level 4 DCC according to the utility model for machine interpretability of DCCs. This also includes basic and quantity-specific refType definitions that are linked to an online refType repository to harmonize these key semantic providing elements across other DCC-issuing laboratories. The paper and also its conference poster will not represent a general introduction and motivation for the DCC itself. It rather addresses more detailed aspects of good practice, especially for DCCs from temperature quantity calibrations and may stimulate in-depth discussions between DCC experts from the providing, utilizing and accrediting points of view. The work was performed within the national QI-Digital initiative of the German Federal Ministry for Economic Affairs and Climate Action, T2 - Global Industrie CY - Lyon, France DA - 11.03.2025 KW - Calibration KW - Digital Calibration Certificate KW - E-Attestation KW - Digital Metrology KW - QI-Digital PY - 2024 AN - OPUS4-64177 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brunner, Nanine A1 - Melzer, Michael T1 - Digital Certificates: Enabling Automation in Quality Assurance and Metrological Traceability N2 - Automation in the metrological traceability of measurements bears high potential for a more effective quality management with less human interaction and reduced risks from manual data processing. For this purpose all metrological and administrative information in quality certificates must be provided in a fully machine-readable and machine-interpretable form. Following the well-established approach of dig-ital calibration certificates (DCCs) also other digital quality certificates are currently under development. T2 - SMSI 2025 Conference – Sensor and Measurement Science International CY - Nuremberg, Germany DA - 06.05.2025 KW - Digital metrology KW - Calibration KW - Quality assurance KW - Reference materials KW - Automation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641930 SN - 978-3-910600-06-5 DO - https://doi.org/10.5162/SMSI2025/C6.4 SP - 171 EP - 172 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-64193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Melzer, Michael T1 - Die Umsetzung maschinenlesbarer DCCs am Beispiel der Kraftkalibrierung nach DIN EN ISO 376 N2 - Dieser Vortrag stellt eine konkrete Umsetzung eines DCCs (Digitaler Kalibrierschein) einer Kraftkalibrierung nach nach DIN EN ISO 376 vor. Nach einer kurzen Zusammenfassung der Aspekte, die in der international gültigen Kalibriernorm geregelt sind und einer allgemeinen Vorstellung von gängigen Kalibriereinrichtungen und -gegenständen, wird zunächst auf die Besonderheiten hingewiesen, die in derartigen Kalibrierscheinen enthalten sind und bisher kaum in anderen DCCs umgesetzt wurden. Dies sind z.B. die Einbindung mehrerer Messreihen (auf- und abwärts) in teilweise unterschiedlichen Einbaupositionen, Klassifizierung, multiple relative Messunsicherheiten sowie Ausgleichsfunktionen mit mehreren Sätzen von Koeffizienten. Anschließen wird die konkrete Umsetzung dieser Angaben im DCC im Einzelnen aufgezeigt. Die präsentierten Lösungen wurden im gemeinsamen DCC Unterausschuss der DKD Fachausschüsse für Kraft und Beschleunigung sowie Drehmoment erarbeitet und werden in Kürze als pränormativer Expertenbericht erscheinen. Die Kalibrierung wurde innerhalb des akkreditierten Geltungsbereiches des BAM Kalibrierlabors durchgeführt. T2 - 329. PTB-Seminar "Berechnung der Messunsicherheit – Empfehlungen für die Praxis" CY - Berlin, Germany DA - 19.05.2025 KW - Calibration KW - Digital Calibration Certificate KW - Force Measurements KW - Digital Metrology KW - QI-Digital PY - 2025 UR - https://www.ptb.de/cms/fileadmin/internet/fachabteilungen/abteilung_8/8.4_mathematische_modellierung/8.42/329_PTB_Seminar/Tag1_S2/DCC-ISO376.pdf AN - OPUS4-64209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fontoura Barroso, Daniel A1 - Epple, Niklas A1 - Niederleithinger, Ernst T1 - A Portable Low-Cost Ultrasound Measurement Device for Concrete Monitoring N2 - This paper describes a new ultrasonic measuring device called “W-Box”. It was developed based on the requirements of the DFG Forschergruppe (research unit) CoDA for a portable device for monitoring of concrete specimens, models and actual structures using embedded ultrasonic transducers as well as temperature and humidity sensors. The W-Box can send ultrasonic pulses with a variable frequency of 50–100 kHz to one selectable transducer and records signals from up to 75 multiplexed channels with a sample rate of 1 MHz and a resolution of 14 bits. In addition, it measures temperature and humidity with high accuracy, adjustable amplification, restarts automatically after a power failure and can be fully controlled remotely. The measured data are automatically stored locally on-site data quality checks and transferred to remote servers. The comparison of the W-Box with a laboratory setup using commercial devices proves that it is equally reliable and precise, at much lower cost. The W-Box also shows that their measurement capacities, with the used embedded ultrasonic transducers, can reach above 6 m in concrete. KW - Low-cost KW - Coda wave interferometry KW - Ultrasound KW - IoT KW - Non-destructive testing PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-546756 DO - https://doi.org/10.3390/inventions6020036 SN - 2411-5134 VL - 6 IS - 2 SP - 1 EP - 17 PB - MDPI CY - Basel, Switzerland AN - OPUS4-54675 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grohmann, Maria A1 - Niederleithinger, Ernst A1 - Maack, Stefan A1 - Buske, Stefan T1 - Application of iterative elastic SH reverse time migration to synthetic ultrasonic echo data N2 - The ultrasonic echo technique is widely used in non-destructive testing (NDT) of concrete objects for thickness measurements, geometry determinations and localization of built-in components. To improve ultrasonic imaging of complex concrete structures, we transferred a seismic imaging technique, the Reverse Time Migration (RTM), to NDT in civil engineering. RTM, in contrast to the conventionally used synthetic aperture focusing technique (SAFT) algorithms, considers all wavefield types and thus, can handle complex wave propagations in any direction with no limit on velocity variations and reflector dip. In this paper, we focused on the development, application and evaluation of a two-dimensional elastic RTM algorithm considering horizontally polarized shear (SH) waves only. We applied the elastic SH RTM routine to synthetic ultrasonic echo SH-wave data generated with a concrete model incorporating several steps and circular cavities. As these features can often be found in real-world NDT use cases, their imaging is extremely important. By using elastic SH RTM, we were able to clearly reproduce almost all reflectors inside the concrete model including the vertical step edges and the cross sections of the cavities.We were also capable to show that more features could be mapped compared to SAFT, and that imaging of complex reflectors could be sharpened compared to elastic P-SV (compressional-vertically polarized shear) RTM. Our promising results illustrate that elastic SH RTM has the potential to significantly enhance the reconstruction of challenging concrete structures, representing an important step forward for precise, high-quality ultrasonic NDT in civil engineering. KW - Ultrasonic echo technique KW - Concrete structures KW - Elastic reverse time migration KW - Synthetic aperture focusing technique KW - Horizontally polarized shear waves PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-591716 DO - https://doi.org/10.1007/s10921-023-01010-3 SN - 1573-4862 VL - 43 SP - 1 EP - 16 PB - Springer Science and Business Media CY - Dordrecht AN - OPUS4-59171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin T1 - Polarization diversity detection based wavelength scanning coherent optical time domain reflectometry N2 - Although wavelength scanning coherent optical time-domain reflectometry (WS-COTDR) system is immune to fading effect, it suffers from occasional and localized large errors caused by the false peak in the correlation spectrum due to the large signal generated in the random interference of the backscattered light. Polarization diversity detection is applied to a standard WS-COTDR system to suppress large measurement errors. In this way, the orthogonally polarized components of backscattered light can be obtained and processed separately. Due to the birefringence of the sensing fiber, the components experience different interference processes, so the average of their correlation spectrum can suppress the false peaks and finally reduce the occurrence of larger errors. The effectiveness of the proposed method is validated in laboratory for monitoring of sinusoidal vibrations and in field for tracking the bus movement via a dark fiber. T2 - 29th International Conference on Optical Fiber Sensors CY - Porto, Portugal DA - 26.05.2025 KW - Coherent optical time domain reflectometry KW - Traffic monitoring KW - Polarization diversity detection KW - Distributed fiber sensing PY - 2025 AN - OPUS4-63260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine T1 - Junior Research Group Materials Characterization and Informatics for Sustainability in Civil Engeneering (CE) N2 - Vorstellung der Themen der Nachwuchsgruppe "Materialcharakterisierung und -informatik für die Nachhaltigkeit im Bauwesen" von Prof. Sabine Kruschwitz (TU Berlin und BAM) T2 - Themenkonferenz Nachhaltiges Bauen CY - Berlin, Germany DA - 08.12.2022 KW - Recycling KW - NMR KW - Materialcharakterisierung KW - Data Science PY - 2022 AN - OPUS4-56648 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Bartholmai, Matthias T1 - Towards Autonomous NDT Inspection: Setup and Validation of an Indoor Localization System N2 - Monitoring and maintenance of civil infrastructure are of great importance, as any undetected damage can cause high repair costs, unintended deadtime, or endanger structural integrity. The inspection of large concrete structures such as bridges and parking lots is particularly challenging and time-consuming. Traditional methods are mostly manual and involve mapping a grid of measurement lines to record the position of each measurement. Current semi-automated methods, on the other hand, use GPS or tachymeters for localization but still require trained personnel to operate. An entirely automated approach using mobile robots would be more cost- and time-efficient. While there have been developments in using GPS-enabled mobile robots for bridge inspection, the weak signal strength in indoor areas poses a challenge for the automated inspection of structures such as parking lots. This paper aims to develop a solution for the automated inspection of large indoor concrete structures by addressing the problem of robot localization in indoor spaces and the automated measurement of concrete cover and rebar detection. T2 - 39th Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Siófok, Hungary DA - 26.09.2023 KW - NDT Inspection KW - Mobile Robot KW - Indoor Localization KW - Setup and Validation PY - 2023 AN - OPUS4-58662 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ulbricht, Alexander T1 - Do Microbes like Additively Manufactured Aluminium? First Details of a Corrosion Test using Sulphate-Reducing Bacteria N2 - Additively manufactured metals become relevant for industrial application. Although many studies on wet corrosion of these metals have been conducted, to the authors knowledge no study seems to contain microbiological corrosion (MIC). In the presented study an experiment was conducted on PBF-LB/AlSi10Mg to test this material's susceptibility for MIC. The tested specimen were analysed using Computed Tomography before and after the MIC experiment to enable a detailed characterisation the damage on the specimens' global and local level. A global reduction of material was observed. In addition, localised damage along process inherent features of the materials microstructure was observed. T2 - Beiratssitzung TF Umwelt CY - Berlin, Germany DA - 17.03.2025 KW - Computed Tomography KW - Additive Manufacturing KW - Biocorrosion KW - Sulphate-reducing Bacteria KW - Microbially influenced corrosion PY - 2025 AN - OPUS4-62772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -