TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Barjenbruch, M. ED - Holm, O. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Nährstoffrückgewinnung aus Klärschlamm: Eine Betrachtung zukünftiger Verwertungsszenarien für Deutschland N2 - Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, in German wastewater treatment plants (WWTPs) phosphorus (P) must be recovered from sewage sludge ifit contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs > 100,000 population equivalents (pe) from 2029 and > 50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 17 % of the total disposal in 2019. The reports of 10 States were evaluated for 2016 and 2017 representing approx. 60 % ofthe total agriculturally used sludge volume. Whereas phosphorus recovery is mandatory this does not apply to other nutrients. However, many P recovery processes recover other nutrients, too. Considering three differentscenariosfor future German sewage sludge disposal Shows that 70 - 77 % ofthe P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0 - 16 % of nitrogen, 36 - 52 % of calcium, 31-53 % of potassium, and 40 - 52 % of magnesium. However, these recovered nutrient loads can substitute only 1 % or less ofthe commercial fertilizer demand except from phosphorus which is about 45 % ofthe demand. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 15.11.2021 KW - Phosphor KW - Klärschlamm KW - Phosphorrückgewinnung KW - Landwirtschaftliche Klärschlammverwertung KW - Klärschlammverordnung PY - 2021 SN - 978-3-944310-56-5 VL - 4 SP - 252 EP - 265 PB - Thomé-Kozmiensky-Verlag GmbH CY - Neuruppin AN - OPUS4-54117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Aktuelle Diskussion aus dem Fachbeirat der BAM N2 - Das Jahr 2020 war vor allen Dingen von der Pandemie geprägt, die alle Bereiche des Lebens und Arbeitens beeinflusst hat und immer noch beeinflusst. Dies hat sich auch auf verschiedene Maßnahmen im Zusammenhang mit zugelassenen Produkten ausgewirkt. In diesem Zusammenhang sollen die Punkte kurz aufgeführt werden. Des Weiteren soll aufgezeigt werden, wie bei der Bearbeitung der Richtlinien, der Zulassungstätigkeit und Beurteilung der Produkte an der BAM und im Fachbeirat vorgegangen wird. Darüber hinaus soll noch einmal kurz auf die Entlassung aus der Nachsorgephase eingegangen werden. Am Ende sollen verschiedene aktuelle Fragestellungen des Fachbeirat aufgezeigt werden. T2 - 17. Leipziger Deponiefachtagung CY - Online meeting DA - 02.03.2021 KW - Deponie KW - Geokunststoffe KW - Kunststoffdichtungsbahn PY - 2021 SN - 978-3-943443-50-9 VL - 17. SP - 31 CY - Leipzig AN - OPUS4-52212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Leimkötter, D. A1 - Hermann, L. A1 - Emter, J. A1 - Brey, C. A1 - Künstler, J. A1 - Hartmann, S. A1 - Krannich, G. A1 - Moggert, N. A1 - Kurz, P. A1 - Eder, C. A1 - Grimm, B. A1 - Adam, Christian ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Success-Story CaNaPO4: Erfolgreiche REACH Registrierung und Inbetriebnahme großtechnischer Anlagen N2 - The Sewage Sludge Ordinance (AbfKlärV), which was amended in 2017, obligate the recovery of phosphorus from sewage sludge and sewage sludge ash from 2029 and 2032, respectively. Thermal disposal of sewage sludge has established itself as the preferred method of disposal, and the capacities of mono-incineration plants are being continuously expanded. Plants for phosphorus recovery, on the other hand, are currently still mainly in the construction, piloting, or commissioning phase. It is estimated that the plant capacities for P recovery planned today will not even be able to cover a quarter of the volume of these ashes in 2029. Therefore, temporary storage of the remaining ashes is currently being discussed to retrieve it later and process it in the P recovery plants, which will then be sufficiently available. It is currently unclear how such interim or long-term storage (> 1 year) should be organized. In addition to legal (fee) issues, the assessment of the technical feasibility of retrievability and the phosphorus recovery potential of landfilled ash remains open. The Institute of Environmental Engineering (ISA) at RWTH Aachen University and the Federal Institute for Materials Research and Testing (BAM) are jointly investigating five deposited ashes that have been dug out and were provided by three landfill operators. The investigations focus on the physical and chemical characterization of these landfilled ashes and its P recovery potential during treatment in thermochemical and wet chemical processes. These results are evaluated in comparison with “fresh,” i.e., non-landfilled sewage sludge ash samples of comparable origin in order to determine the influence of storage. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Phosphor KW - Recycling KW - Thermochemisch KW - Dünger KW - Großtechnik PY - 2025 SN - 978-3-911006-63-7 VL - 8 SP - 236 EP - 256 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-64833 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus dem Fachbeirat der BAM N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. Besondere Aufmerksamkeit gilt der Diskussion um die Einbauhilfe im Schutzschichtsystem, der Einführung einer europäischen Zugversuchsnorm für Kunststoffdichtungsbahnen sowie der Fremdüberwachung der Produktion geosynthetischer Komponenten. Darüber hinaus werden neue Anforderungen an Edelstahlelektroden in Dichtungskontrollsystemen und die Spannungsrissbeständigkeit von PE-HD-Dichtungsbahnen thematisiert. T2 - 35. Karlsruher Deponie- und Altlastenseminar CY - Karlsruhe, Germany DA - 15.10.2025 KW - Deponie PY - 2025 VL - 48 SP - 26 EP - 35 PB - ICP AN - OPUS4-64408 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, S. A1 - Herzel, Hannes A1 - Adam, Christian A1 - Montag, D. ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Langzeitlagerung von Klärschlammaschen ab 2029? Erste Erfahrungen zur Phosphorrückgewinnung aus deponierten Klärschlammverbrennungsaschen N2 - Das Institut für Siedlungswasserwirtschaft (ISA) der RWTH Aachen University sowie die Bundesanstalt für Materialforschung und -prüfung (BAM) untersuchen gemeinsam fünf deponierte KSA, die von drei Deponiebetreibern ausgebaut und zur Verfügung gestellt wurden sind. Im Fokus der Untersuchungen stehen die physikalische und chemische Charakterisierung der deponierten KSA sowie deren P-Rückgewinnungspotenzial bei der Behandlung in thermochemischen sowie nasschemischen Verfahren. Diese Ergebnisse werden im Vergleich mit „frischen“, also nicht deponierten KSA-Proben vergleichbarer Herkunft bewertet, um so den Einfluss der Lagerung auf die KSA zu erfassen. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Klärschlammasche KW - Recycling KW - Deponie KW - Monoverbrennung PY - 2025 SN - 978-3-911006-63-7 VL - 8 SP - 192 EP - 202 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-65017 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Joachim A1 - Adamczyk, Burkart A1 - Ebert, Dominik A1 - Ehrenberg, Andreas A1 - Schraut, Katharina A1 - Algermissen, David A1 - Adam, Christian T1 - Usage of BOF slag and next generation EAF slag in the cement industry N2 - When the transformation of its production routes, which the European steel industry aims to complete within the next two decades, is accomplished, increased amounts of EAF slag will be generated. In most cases the BF/BOF production route is intended to be substituted by a DRI/EAF combination. But in some cases only the BF will be substituted by a DRI/SAF (smelter) combination and the BOF process remains. Then BOF slags will remain, too. BAM and FEhS cooperate together with further research and industry partners in two research projects dealing on the one hand with the utilisation of modified BOF slag as a cement clinker substitute ("SlagCEM") and on the other hand with the use of modified and granulated EAF slag as granulated blast furnace slag (GBS) substitute ("DRI-EOS"). T2 - 9th International Slag Valorisation Symposium CY - Leuven, Belgium DA - 08.04.2025 KW - Steel slags KW - Basic oxygen furnace (BOF) KW - Electric arc furnace (EAF) KW - Cement KW - Slag valorisation PY - 2025 SP - 187 EP - 191 AN - OPUS4-64713 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Weimann, Karin A1 - Gluth, Gregor T1 - Erzeugung klimaschonender Bindemittel als Alternativen zu Zement durch thermochemische Behandlung von mineralischen Nebenprodukten und Abfällen N2 - Die Zementindustrie erzeugt etwa 6-7% der globalen CO2-Emissionen und steht damit als Industriezweig vor dem Hintergrund einer anvisierten Klimaneutralität vor gewaltigen Herausforderungen. Der Prozess der Klinkerherstellung wurde über die vergangenen Jahrzehnte bereits kontinuierlich optimiert. Seit 1990 ist es der deutschen Zementindustrie gelungen, die spezifischen CO2-Emissionen der Zementproduktion u. a. durch den Einsatz alternativer, nicht fossiler Brennstoffe und durch Absenkung des Klinkergehalts im Zement um 20 % zu senken. Weitere konventionelle Minderungsstrategien versprechen jedoch nur noch wenig zusätzliche Reduktion. Im Falle des Portlandklinkers besteht die Schwierigkeit darin, dass zwei Drittel der CO2-Emissionen rohstoffbedingt durch die Entsäuerung des Kalksteins (CaCO3) anfallen, die durch die beschriebenen Maßnahmen nicht weiter abgesenkt werden können. Vielmehr wird es erforderlich sein, noch zu entwickelnde oder zu optimierende Technologien anzuwenden und ggf. alle relevanten Ebenen wie Produktion, Weiterverarbeitung und Anwendung von Zement und Beton neu zu denken. Neben technologischen Ansätzen zur CO2-Abscheidung mit nachfolgender langfristiger Speicherung (Carbon Capture and Storage – CCS) oder Verwertung (Carbon Capture and Utilisation – CCU) werden auch alternative Rohstoffe für die Zementproduktion und alternative Bindemittel in Betracht zu ziehen sein. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Sekundärrohstoff PY - 2022 SN - 978-3-944310-58-9 SP - 372 EP - 385 PB - TK-Verlag CY - Neuruppin AN - OPUS4-54737 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph T1 - ISO 27913 - Example For Successful Standardization Activities In The Field Of CCUS N2 - Since 2016 ISO Technical Committee (TC) 265 is working on standardization the whole CCS-process chain. Around 30 countries are working together to provide international guidelines. As ISO 27913 was the first standard finished within these activities it is already in the stage of first revision. The objective of ISO 27913 is “to provide specific requirements and recommendations on certain aspects of safe and reliable design, construction and operation of pipelines intended for the large-scale transportation of CO2 that are not already covered in existing pipeline standards such as ISO 13623, ASME B31.8, EN 1594, AS 2885 or other standards. Existing pipeline standards cover many of the issues related to the design and construction of CO2 pipelines; however, there are some CO2 specific issues that are not adequately covered in these standards. The purpose of this document is to cover these issues consistently. Hence, this document is not a standalone standard, but is written to be a supplement to other existing pipeline standards for natural gas or liquids for both onshore and offshore pipelines.” This contribution shall provide information on the content, the current stage of the revision process, encourage to contribute to this standard and make listeners aware to consider the influence of ISO standard on documents currently in draft. T2 - AMPP's Annual Conference + Expo 2024 CY - New Orleans, LA, USA DA - 02.03.2024 KW - Corrosion resistant materials KW - Carbon dioxide KW - Corrosion prevention KW - Standardization KW - CCUS KW - CCS KW - CCU PY - 2024 SP - 1 EP - 6 PB - AMPP CY - Houston AN - OPUS4-59735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Sturm, Patrick A1 - Kühne, Hans-Carsten A1 - Gluth, Gregor ED - Bishnoi, S. T1 - Comparison of brick clays and a kaolinitic clay regarding calcination and performance in blended cement mortars N2 - Two brick clays (rich in 2:1 clay minerals) and a low-grade kaolinitic clay were studied regarding their transformations during calcination and their performance in blended cement mortars. The mortars with calcined clays exhibited decreased workability (slump flow), but this effect could be mitigated by employment of a conventional superplasticizer; however, compressive strength of the hardened mortar was lowered in some cases. While the kaolinitic clay generally yielded the highest strength, the performance of a brick clay could be increased by grinding to higher fineness and by mixing it with the kaolinitic clay. T2 - 3rd International Conference on Calcined Clays for Sustainable Concrete CY - New Delhi, India DA - 15.10.2019 KW - Calcined clays KW - Blended cements KW - Workability KW - Supplementary cementitious materials PY - 2020 SN - 978-981-15-2805-7 DO - https://doi.org/10.1007/978-981-15-2806-4_10 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 25 SP - 85 EP - 93 PB - Springer CY - Singapore AN - OPUS4-50663 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Law, D. W. A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Gunasekara, C. ED - Valente, I. B. ED - Ventura Gouveia, A. ED - Dias, S. S. T1 - Effect of Curing Temperature on the Alkali Activation of German Brown Coal Fly Ash N2 - Due to environmental concerns regarding the use of Portland cement as the principal binder material in concrete and mortar it is imperative to identify alternative materials that could reduce the carbon footprint of the construction industry. One alternative to address these issues is the use of alkali activated materials, in particular, when based on waste streams that currently have no or only limited industrial application. This paper reports a preliminary study into the synthesis of geopolymer mortar utilizing Brown Coal Fly Ash. The ash had a CaO content of ~39%, indicating that synthesis at ambient or low temperature may be feasible. The paper reports initial trials on the effect of curing temperature, ambient to 120 °C, on the mechanical properties of the mortars produced. The results showed that ambient cured mortar achieved a compressive strength of 6.5 MPa at 3 days. A curing temperature of 60 °C gave the optimum results with a compressive strength of almost 20 MPa and a flexural strength of 3.5 MPa obtained. T2 - 3rd RILEM Spring Convention and Conference (RSCC 2020) CY - Guimarães, Portugal DA - 10.03.2020 KW - Alkali-activated materials KW - Brown Coal Fly Ash KW - Lignite Coal PY - 2021 SN - 978-3-030-76550-7 SN - 978-3-030-76551-4 DO - https://doi.org/10.1007/978-3-030-76551-4_7 SP - 69 EP - 77 PB - Springer CY - Cham AN - OPUS4-53072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gawlitza, Kornelia A1 - Johann, Sergej A1 - Mansurova, Maria A1 - Kohlhoff, Harald A1 - Tiebe, Carlo A1 - Bell, Jérémy A1 - Bartholmai, Matthias A1 - Rurack, Knut T1 - Semi-automatic Measurement Device for Long-Term Monitoring of Ammonia in Gas Phase N2 - In the present paper the development of a semi-automated device for long-term monitoring of gaseous ammonia is described. A sensor material was produced that changes its optical properties in the pres-ence of low concentrations of ammonia in air. The implementation into an electronic device enables precise, simple, economic and fast monitoring of low concentrations of harmful gases, like ammonia, and hence can help to improve the climate monitoring in livestock housing, barns or stables. T2 - SMSI 2021 CY - Online meeting DA - 03.05.2021 KW - Spectroscopy KW - Embedded sensor KW - Environment KW - Air quality PY - 2021 SP - 133 EP - 134 AN - OPUS4-52576 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gawlitza, Kornelia A1 - Johann, Sergej A1 - Mansurova, M. A1 - Kohlhoff, Harald A1 - Tiebe, Carlo A1 - Bell, Jérémy A1 - Bartholmai, Matthias A1 - Rurack, Knut T1 - Semi-automatic Measurement Device for Long-Term Monitoring of Ammonia in Gas Phase N2 - The present paper describes the development of a sensor material that changes its fluorescence in the presence of gaseous ammonia in a relevant concentration range. The implementation into a semi-automatic gas measurement device enables low-cost, precise, simple and fast monitoring of low con-centrations of harmful gases, like ammonia, and hence can help to improve the climate monitoring in livestock housing, barns or stables. T2 - SMSI 2020 CY - Meeting was canceled KW - Spectroscopy KW - Emmbedded sensor KW - Environment KW - Air quality PY - 2020 DO - https://doi.org/10.5162/SMSI2020/B5.4 SP - 133 EP - 134 AN - OPUS4-50867 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Johann, Sergej A1 - Tiebe, Carlo A1 - Kohlhoff, Harald A1 - Bartholmai, Matthias T1 - Feasibility Study for Safe Workplaces through automation and digitalization technology with redesigned Smart Sensors and LoRaWAN Monitoring System N2 - This project addresses the application of safe and healthy workplaces in offices, chemical laboratories and other workplaces where indoor air quality plays an important role. The LoRaWAN (Long Range Wide Area Network) is used as a communication interface to make sensor data globally accessible. The objectives of the project are to create a sensor node and an online and offline system that collects the data from the sensor nodes and stores it on a local server, in a cloud, and also locally on the node to prevent communication failures. An important point in this project is the development of the sensor nodes and the placement of these in the premises, thus no development work is involved in Building the infrastructure. T2 - SMSI 2021 CY - Online meeting DA - 03.05.2021 KW - Smart sensors KW - Air quality monitoring KW - LoRaWAN KW - VOC KW - Multisensor system PY - 2021 SP - 230 EP - 231 AN - OPUS4-52649 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moufid, M. A1 - Tiebe, Carlo A1 - El Bari, N. A1 - Bartholmai, Matthias A1 - Bouchikhi, B. T1 - Characterization of Unpleasant Odors in Poultry Houses Using Metal Oxide Semiconductor-Based Gas Sensor Arrays and Pattern Recognition Methods N2 - In this study, the ability of an electronic nose developed to analyze and monitor odor emissions from three poultry farms located in Meknes (Morocco) and Berlin (Germany) was evaluated. Indeed, the potentiality of the electronic nose (e-nose) to differentiate the concentration fractions of hydrogen sulfide, ammonia, and ethanol was investigated. Furthermore, the impact change of relative humidity values (from 15% to 67%) on the responses of the gas sensors was reported and revealed that the effect remained less than 0.6%. Furthermore, the relevant results confirmed that the developed e-nose system was able to perfectly classify and monitor the odorous air of poultry farms. T2 - 1st International Electronic Conference on Chemical Sensors and Analytical Chemistry CY - Online meeting DA - 01.07.2021 KW - Pattern recognition methods KW - Gas sensors KW - Electronic nose KW - poultry odorous air monitoring PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-544005 UR - https://csac2021.sciforum.net/ DO - https://doi.org/10.3390/CSAC2021-10481 VL - 5 IS - 52 SP - 1 EP - 7 PB - MDPI AN - OPUS4-54400 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nicolicea, Alberto A1 - Pelkner, Matthias A1 - Melzer, Michael A1 - Oliveros-Mata, E. S. A1 - Zabila, Y. A1 - Makarov, D. T1 - Flexible AMR sensors for novel non-destructive testing capabilities N2 - Reshapeable magnetic field sensors fabricated on flexible substrates by thin-film deposi-tion or printing have recently emerged with promising applications in different field. In this study, flexible anisotropic magneto-resistive (AMR) sensors were used for the scanning of a curved and flat sample with reference defects, to prove the capability of this method for curved surface scanning, and to benchmark the performance when compared to a more standard method using rigid giant magneto-resistive (GMR) sensors. Defects with depths ranging from 110 μm up to 2240 μm were detected with a signal-to-noise ratio (SNR) of 2.7 up to 27.9 employing flexible AMR sensors. T2 - XMR-Symposium CY - Wetzlar, Germany DA - 12.03.2025 KW - non-destructive testing KW - Flexible sensor KW - Magnetoresistance PY - 2025 SP - 1 EP - 6 AN - OPUS4-65045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Davenport, John A1 - Lorek, Andreas A1 - Garland, Stephen A1 - Schwanke, Volker A1 - Wernecke, Roland T1 - Gasfeuchtemessung in der Normung N2 - Schwefelhexafluorid (SF6) ist ein 22.800-mal stärkeres Treibhausgas als CO2, wird aber aufgrund seiner isolierenden Eigenschaften in Mittel- und Hochspannungssystemen wie Schaltanlagen eingesetzt. Voraussetzung für die Durchschlagfestigkeit ist ein geringer Wasserdampfgehalt. Viele aktuelle Feuchtigkeitssensoren zeigen jedoch eine Querempfindlichkeit gegenüber CO2. Diese Richtlinienarbeit zielt darauf ab, den aktuellen Stand der Technik zu erweitern und neue Erkenntnisse zu gewinnen. Abschließend erfolgt eine Erweiterung der Richtlinie zur Gasfeuchte-Messung VDI/VDE 3514. T2 - GMA/ITG – Fachtagung Sensoren und Messsysteme 2024 CY - Nuremberg, Germany DA - 11.06.2024 KW - Gassensorik KW - Industrienormen KW - SF6 PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-604597 DO - https://doi.org/10.5162/sensoren2024/P32 SP - 547 EP - 549 PB - GMA/ITG – Fachtagung Sensoren und Messsysteme 2024 CY - Nürnberg AN - OPUS4-60459 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaad, C. A1 - Tiebe, Carlo A1 - Groth, Katrina M. T1 - A Framework for Transforming Process Control System Data from a Hydrogen Fueling Station into HyCReD Data N2 - Reliability data for hydrogen infrastructure components is essential for developing Quantitative Risk Assessment (QRA) for these technologies, which in turn is necessary for a safer deployment and expansion of the hydrogen market. However, there is currently a lack of hydrogen component reliability data available for these systems, thus limiting the usefulness of insights obtained from these QRA. The Hydrogen Component Reliability Database (HyCReD) has been proposed as a tool for reliability data collection and as a source for future QRAs. In this paper, we develop a digital tool that automatically processes data coming from Process Control System (PCS) in a hydrogen fueling station, detects the relevant failure events for hydrogen systems during its operation, and then logs the event information into HyCReD. To build this tool, we first categorized the station components in hydrogen service, their specific failure modes, and the specific failure mechanisms that are relevant to a QRA. Then, we identified the data available in the station PCS and the methods available for diagnosing the relevant failure events. The resulting tool is divided into three steps: (1) PCS data collection through an API, (2) data analysis for the detection and diagnosis of new failure events, and (3) logging that event into HyCReD. Finally, we discuss the potential for expanding the detection and diagnosis to more complex failure modes present in a hydrogen fueling station. This digital tool is set for implementation and validation on an experimental hydrogen fueling site. The goal for this digital tool is to be applicable to every kind of hydrogen fueling station and to be extendable to similar hydrogen technologies. T2 - 35th European Safety and Reliability Conference (ESREL2025) and the 33rd Society for Risk Analysis Europe Conference (SRA-E 2025) CY - Stavanger, Norway DA - 15.06.2025 KW - Reliability data KW - Hydrogen safety KW - HyCReD KW - Hydrogen Component Reliability Database KW - Hydrogen fueling station KW - Hydrogen refuelling station KW - HRS PY - 2025 UR - https://rpsonline.com.sg/proceedings/esrel-sra-e2025/html/ESREL-SRA-E2025-P6264.html SN - 978-981-94-3281-3 DO - https://doi.org/10.3850/978-981-94-3281-3-procd SP - 2663 EP - 2670 PB - Research Publishing CY - Singapore AN - OPUS4-63532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moufid, M. A1 - Tiebe, Carlo A1 - El Bari, N. A1 - Bartholmai, Matthias A1 - Bouchikhi, B. T1 - Combining of TD-GC-MS and home developed electronic nose for road traffic air monitoring N2 - In this work, we demonstrate the ability of an electronic nose system based on an array of six-semiconductor gas sensors for outdoor air quality monitoring over a day at a traffic road in downtown of Meknes city (Morocco). The response of the sensor array reaches its maximum in the evening of the investigated day which may due to high vehicular traffic or/and human habits resulting in elevated concentrations of pollutants. Dataset treatment by Principal Component Analysis and Discriminant Function Analysis shows a good discrimination between samples collected at different times of the day. Moreover, Support Vector Machines were used and reached a classification success rate of 97.5 %. Thermal Desorption-Gas Chromatography-Mass Spectrometry (TD-GC-MS) technique was used to validate the developed e-nose system by identifying the composition of the analyzed air samples. The discrimination obtained by e-nose system was in good agreement with the TD-GC-MS results. This study demonstrates the usefulness of TD-GC-MS and e-nose, providing high accuracy in discriminating outdoor air samples collected at different times. This demonstrates the potential of using the e-nose as a rapid, easy to use and inexpensive environmental monitoring system. T2 - 2021 IEEE International Conference on Design & Test of Integrated Micro & Nano-Systems (DTS) CY - Sfax, Tunisia DA - 07.06.2021 KW - GC-MS KW - Electronic nose KW - Gas sensors KW - Urban air monitoring PY - 2021 DO - https://doi.org/10.1109/DTS52014.2021.9498110 SP - 1 EP - 6 AN - OPUS4-54401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Farago, Patrick A1 - Mayer, Felix ED - Angulo, Sergio ED - Landmann, Mirko T1 - New sources for secondary gypsum N2 - In order to protect natural gypsum deposits and to compensate for the decreasing amount of Flue Gas Desulfurization (FGD) gypsum it is necessary to develop and explore new sources of gypsum. For this purpose, the potentials of different gypsum wastes are investigated in the study “GipsRec 2.0”, funded by the Federal Ministry of Education and Research (Germany). On the one hand, the project worked on a new processing technology for gypsum fiberboards (GFB). While the recycling of gypsum plasterboards has already been carried out on an industrial scale for several years, the recycling of gypsum fiberboards (GFB) has proven to be challenging. Gypsum fiberboards from demolition sites and offcuts from GFB production were used for these investigations. The tests were conducted on a technical scale. Furthermore, various synthetic gypsums are being investigated with regard to their suitability for gypsum production. The analyses are carried out on production residues. In this project, a promising process for gypsum fiberboard recycling could be developed, as well as other waste gypsums are investigated and evaluated with regard to their potential as secondary raw material. In addition, selected process routes are assessed for their environmental impact using a life cycle assessment (LCA) approach. T2 - RILEM - V International Conference Progress of Recycling in the Built Environment CY - Weimar, Germany DA - 10.10.2023 KW - Gypsum recycling KW - Gypsum fiberboards and synthetic gypsum KW - Environmental evaluation PY - 2023 VL - V SP - 1 EP - 10 PB - RILEM Publications Sarl CY - Bagneux, France AN - OPUS4-60315 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Tino A1 - Neumann, Patrick P. A1 - Weller, Michael G. T1 - A New Approach: Passive Smart Dust for Detection of Hazardous Substances N2 - Remote sensing of hazardous substances is a key task that can be achieved with the help of remotely operated platforms equipped with specific sensors. A huge variety of methods and used vehicles have been developed for different purposes in recent years. The term smart dust refers to a science fiction novel and develop shortly after into a research proposal at UC Berkley funded by DARPA. Subsequently, the topic gained attraction but was overall considered as to complex for the technologies available at that time. In the launched passive smart dust project, we shift to a simple “chemical intelligent” passive sensor particle on the ground combined a read-out active sensor attached to an Unmanned Aerial Vehicle (UAV). The reactive particle surface can be preadjusted in the lab for exact desired properties regarding certain reactions to hazardous substances. Moreover, the aimed interaction with the active sensor can be modified. Planed applications allow for different materials e.g., for short time measurement, being ecologically degradable, or weather stable for long time monitoring. T2 - 38th Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Poros, Greece DA - 20.09.2022 KW - Smart Dust KW - Drone KW - Remote Detection KW - Hazardous substances PY - 2022 SP - 1 EP - 2 CY - Athens, Greece AN - OPUS4-55925 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Tino A1 - Neumann, Patrick P. A1 - Weller, Michael G. T1 - Drone-based Localization of Hazardous Chemicals by Passive Smart Dust N2 - We introduce a passive smart dust concept as a novel solution for environmental monitoring. Utilizing chemical reagents like colorimetric indicators and other chemosensors, these particles detect varying environmental conditions. We developed paper-based sensors that are both cost-effective and eco-friendly. In practical tests, these sensors, dispersed over a designated area, successfully identified hazardous substances by changing their color when exposed to acids or bases. This color change was remotely detectable using a drone-mounted color camera. The data thus obtained was processed through specialized software, accurately pinpointing areas of contamination. This method proves the efficacy and scalability of passive smart dust technology for real-time, environmentally sustainable remote sensing of hazardous materials T2 - 2024 IEEE International Symposium on Olfaction and Electronic Nose (ISOEN) CY - Grapevine, Texas, USA DA - 12.05.2024 KW - Indicator KW - Passive Smart Dust KW - Colorimetric Sensor KW - Drone KW - Cellulose KW - Environmental Monitoring KW - Confetti KW - Hazard Detection PY - 2024 SN - 979-8-3503-7053-9 VL - 1 SP - 1 EP - 3 PB - IEEE CY - Piscataway, NJ 08855-1331 USA AN - OPUS4-60176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Tino A1 - Neumann, Patrick P. A1 - Weller, Michael G. T1 - Passive Smart Dust a versatile low-cost sensor platform N2 - Coated cellulose particles as colourimetric passive sensors that are detected by the optical camera system of a drone. In this way, hazardous substances, e.g. acids, can be detected from a safe distance in a cost-effective and environmentally friendly way. N2 - Beschichtete Zellulose Partikel als kolorimetrische passive Sensoren, die mittels optische Kamerasystem einer Drohne erfasst werden. Somit können Gefahrenstoffe, in ersten Versuchen zB Säuren aus sicherer Entfernung, kostengünstig und umweltverträglich detektiert werden. T2 - SMSI 2023 Sensor and Measurement Science International CY - Nuremberg, Germany DA - 08.05.2023 KW - Passive Smart Dust KW - Drone KW - Colorimetric sensor particles KW - Remote detection PY - 2023 DO - https://doi.org/10.5162/SMSI2023/C5.3 SP - 1 EP - 2 AN - OPUS4-57527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Visileanu, Emilia A1 - Catalin Grosu, Marian A1 - Tiberiu Miclea, Paul A1 - Altmann, Korinna A1 - Brossell, Dirk T1 - Methods for the collection and characterization of airborne particles in the textile industry N2 - Airborne particulate matter is one of the main air pollutants. Their impact on mortality, and the occurrence of pulmonary and cardiovascular complications, have been the subject of numerous studies. Airborne particles are complex mixtures of organic and inorganic substances from different sources of particle emissions. Particulate Matter (PM) particles are classified according to their aerodynamic diameter expressed in µm and can vary from coarse (PM 10) to fine (less than PM 2.5). These diameter considerations are fundamental because they condition the penetration of particles into the bronchopulmonary system and the body. In recent years, there has been an interest in so-called “ultra-fine” particles, with a diameter of 0.1 µm (or 100 nm), or PM 0.1. They are nanoparticles and their impact on human health is not yet clear.With more than 1.5 million employees, textiles and clothing is a diverse sector that plays an important role in the European manufacturing industry, producing a turnover of €162 billion.An important component of the solid particles that generate air pollution in the textile industry is microplastics (MP) and nano plastics (NP), which also include microfibers (<5mm) and nanofibers (<100 nm), respectively. The particles released into the air during fiber and yarn processing range from 1 µg/m3 to 50 µg/m3.The paper presents the results of the determination of indoor and outdoor air concentration levels in textile companies, to identify the areas with the highest concentration level, by using an online recording system such as the Laser Aerosol Spectrometer MINI LAS model 11-E. The total concentration level TSP (µg/m3), the fractions PM 10(µg/m3), PM 2.5(µg/m3), PM1(µg/m3), as well as the total number of particles TC (1/l), were shown. It was noted that TSP is approximately at the same level both indoors and outdoors, but the fractions of PM10, PM2.5, and PM1 have much higher values indoors than outdoors with possible consequences on workers' health.The next step was the collection of fibers, namely micro and nano plastic particles from the vicinity of the workplaces of polyester, polyamide, and polypropylene fibers processing units in the textile industry in Romania, to obtain a sufficient quantity for laboratory analysis to determine the size and shape of the particles as well as their chemical composition. Two types of pumps were used, differentiated by their operating parameters: TECORA SKYPOST with airflow of 38 l/min and GILAIRPLUS with airflow 2l/min. Filters made of different materials with different diameters and pore sizes were used, namely: quartz filters (ø 47 mm, and ø 37 mm) on a TECORA SKYPOST type pump, polycarbonate nucleopore coated with a gold membrane (ø 25 mm) and silica filter (ø 9 mm) on GILAIRPLUS type pump.Using descriptive statistics, the calculation of correlation coefficients highlighted a strong correlation between the variables: "Collected mass/ Air concentration" and "Collected mass/ Air volume" for all diameters of the filters.The highest collected particle volume, determined by weighing the filters before and after collection, was obtained with the quartz filters (ø 47 mm) at an airflow of 38 l/min. The particles collected (polyester, polyamide, polypropylene) in the first stage were analyzed by SEM and thermogravimetric and it was found that the quartz filters absorbed the particles inside, with very few remaining on the surface. Thus no known methods can be used to perform analysis for particles collected on quartz filters. The number of particles on the filters was insufficient for analysis either because of the collection parameters used or because of the loss of particles during transport. As a result, in the next step, the use of 9 mm Si filters using the GILAIRPLUS pump at an airflow rate of 2l/min was chosen.To improve the transport conditions and avoid the loss of the particles and keep them on the surface of the filters, two methods were applied:- after weighing the filters were reintroduced into the collection pump holder;- a filtration system for airborne micro-nano plastics was designed and manufactured to selectively collect and transport PM10 and PM1 particles collected on SI filters.In both cases, SEM, Raman mapping, and GS-MS microscopy were used for analysis.Several times more PM10 than PM1 (74.5µg compared to 12.5 µg) was found. In all cases, both particles and fibers showed the same Raman fingerprint.The GS-MS analyses showed some contamination of the workspaces with particles other than the processed fibers. The presence of non-notifiable substances was also observed.The most viable filters are Si filters with a pore size of 10 microns to 1 micron and the use of the selected collection and transport filter system. In the following a filter system will be applied for collection on Au membrane-coated polycarbonate filters. T2 - 5th International Conference on Human Systems Engineering and Design: Future Trends and Applications (IHSED 2023) KW - Microplastics KW - Textiles PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624442 DO - https://doi.org/10.54941/ahfe1004132 VL - 112 SP - 212 EP - 223 PB - AHFE International AN - OPUS4-62444 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrke, Heiko A1 - Kohlhoff, Harald A1 - Erdmann, Jessica A1 - Winkler, Nicolas P. A1 - Neumann, Patrick P. T1 - Combined GNSS/Visual Inter-Robot Tracking Method for Open-Path Gas Tomography N2 - Methane emissions are a significant environmental and safety concern, yet many gas tomography systems intended to measure them require manual alignment, reliable high-bandwidth links, or fiducials. We present a lightweight, fully autonomous framework enabling line-of-sight inter-robot Tunable Diode Laser Absorption Spectroscopy (TDLAS) measurements without such constraints. A sensor robot equipped with a gimbal-mounted TDLAS unit tracks a reflector robot bearing an illuminated, color-controllable target. Coarse localization is achieved via RTK-GNSS, with vision-based fine tracking and passive time synchronization handled onboard. The system, based on off-the-shelf Pixhawk controllers and ArduPilot firmware, was validated in a 15m × 7m outdoor trial. Despite GNSS inaccuracies and deliberate occlusion by a methane-filled bag, the system retained lock, recovered from visual loss in under one second, and captured a 2800 ppm·m plume signature. These results demonstrate robust, scalable methane sensing for mobile gas tomography or standalone leak detection. Core components are released open-source to support future deployment. T2 - IEEE SENSORS 2025 CY - Vancouver, BC, Kanada DA - 19.10.2025 KW - Gas tomography KW - Tracking KW - Robot KW - Methane KW - TDLAS PY - 2025 SN - 979-8-3315-4467-6 DO - https://doi.org/10.1109/SENSORS59705.2025.11330519 SP - 1 EP - 4 PB - IEEE CY - Piscataway, NJ, USA AN - OPUS4-65615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. T1 - Simulationsdaten zur photooxidativen Beanspruchung an verschiedenen geografischen Freibewitterungs-Standorten N2 - Freibewitterungen weisen grundsätzlich eine hohe Variabilität der jeweiligen Intensität der Beanspruchungsparameter auf; sie sind nicht einfach wiederholbar. Um dennoch die Ergebnisse einer Beanspruchung vergleichen zu können, ist eine aussagekräftige Charakterisierung der Freibewitterung wichtig. Traditionell werden Daten bekannter Einflussgrößen wie Globalstrahlung, Temperatur oder Feuchtewerte herangezogen. Obwohl man weiß, dass diese Größen an den exponierten Oberflächen wechselwirken und kombiniert als Mikroklima Einfluss auf Degradationsprozesse nehmen, werden schon aus Praktikabilitätsgründen diese separat als klimatische Messgrößen angegeben. Die Aussagekraft dieser Daten ist mäßig. Ziel dieses Beitrags ist es, die Aussagekraft und damit Vergleichbarkeit zu erhöhen, indem diese Messdaten als Stundendaten zu Wirkintegralen vorverarbeitet und jahresweise akkumuliert werden. Betrachtet wird dafür der Prozess der Photooxidation, da dieser Alterungs-mechanismus bei allen Kunststoffen auftritt. Für eine einfache Modellierung wird die wirksame UV-Bestrahlung, gewichtet mit einer Arrhenius-abhängigen Ober¬flächen-temperatur (TOF), über den Beanspruchungszeitraum von hier je einem Jahr akkumuliert. Die Idee einer solchen Messgröße für photooxidative Ober¬flächen¬alterung wurde bereits vorgestellt [1]. Dort wurde ein Gerät vor¬geschlagen, mit dem dieser Wert für verschieden absorbierende Oberflächen für die Dauer einer Exposition akkumuliert wird, und ergänzend eine Abschätzung der Betauungs¬zeiten dieser Referenz-Oberflächen erfolgen könnte. Hier soll es um eine rechnerisch generierte Zusammenstellung dieser photo¬oxidativen 1-Jahres-Alterungswerte für verschiedene Standorte gehen. Ein Temperaturfaktor erfasst dabei den Einfluss der Strahlungserwärmung auf eine weiße, graue bzw. schwarze Referenzoberflächen, spiegelt also die Kopplung von solarer Strahlung und Temperatur wider [1]. Ermittelt wird er aus Stunden¬daten der Globalstrahlung und der Lufttemperatur. Die spektrale Wirkung wird aus Sonnenhöhenständen entsprechend der geografischen Breite mit Hilfe der FastRT-Oberfläche [2] als PiT·h-Wert abgeschätzt [3]. Anhand der errechneten Jahreswerte können die Schweregrade der photo¬oxidativen Beanspruchung an den verschiedenen Standorten unmittelbar verglichen werden. Die gezeigten Simulationsdaten für ein solches „elektronisches Referenzmaterial“ für photooxidative Degradation zeigen die prinzipielle Möglichkeit einer Kartografierung solcher Daten auf. T2 - 53. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 26.03.2025 KW - Polymer 3R, UV, Bestrahlung, Bewitterung PY - 2025 SN - 978-3-9826129-2-8 VL - 53 SP - 19 EP - 28 PB - Gesellschaft für Umweltsimulation e.V. CY - 76327 Pfinztal (Berghausen) AN - OPUS4-62902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Trubiroha, Peter A1 - Wachtendorf, Volker T1 - Significance of new data pairs for irradiance and (surface) temperature N2 - There is consent that UV irradiance and temperature at the place of photodegradation are the most important environmental parameters in weathering, along with humidity. This contribution shows how an improvement in the measurement data situation can improve the significance and comparability of outdoor exposures. Photooxidative ageing is calculated using sample polymers for which the corresponding modelling data (Exposure Response Functions, ERF) is available. The mean square deviations are estimated, which result from using different spectral irradiances and different spectral sensitivities, both of the sensors and the polymers. It will be shown here how the significance of the irradiance values increases with increasing approximation of the spectral sensitivities of the sensor and polymer. Also, the mean square deviations are estimated, which result from using different activation energies and surface temperatures. A selection of different variables to describe the weathering exposure is created. The potential of either individual values or data pairs is evaluated in terms of significance or correlation to the calculated photooxidative ageing. Recording hourly data also enables subsequent evaluations of individual test specimens, adapted to the respective colour or to determine activation energies. An accumulated value, calculated from PIT-radiometer irradiance and a suited surface temperature, can provide a comparison of different outdoor exposures over different locations or years. Thus, a characterisation of the weathering exposure would be related to a reference spectral sensitivity (much closer to a polymer than that of a common UV radiometer), one reference activation energy, and different surface temperature scenarios with, on the one hand, graded solar absorptions (white / grey / black) and, on the other hand, different thermal couplings (coated metal / thick plastic). This results in three values each for plastic samples and coated metals (light / grey / dark). It will never be possible to accurately predict the weathering tests for individual samples (with their specific sensitivities), but the proposed approaches can go a long way towards the comparability of outdoor weathering exposures. T2 - 10th European Weathering Symposium EWS CY - Graz, Austria DA - 11.09.2024 KW - Polymer 3R KW - Outdoor weathering PY - 2024 SN - 978-3-9826129-1-1 SP - 121 EP - 133 PB - Stober Medien GmbH CY - Eggenstein AN - OPUS4-61291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. A1 - Giehl, A. A1 - Schönlein, A. A1 - Feil, F. T1 - Normenvorschlag zur Bewitterung transparenter oder transluzenter Kunststoffe N2 - Aufgrund des tieferen Eindringens der solaren Strahlung treten bei transparenten und bei transluzenten (durchscheinenden) Kunststoffen veränderte Bedingungen gegenüber opaken Proben auf. Dies kann zu speziellen Effekten und damit zu einem abweichenden Bewitterungsverhalten führen. Auch aus Mangel an geeigneten Normen werden diese Effekte häufig vernachlässigt. Deshalb initiiert der DIN-FNK auf ISO-Ebene ein entsprechendes Dokument. Die Norm ist in der Form eines Technical Reports geplant. In einem ersten Teil sollen die Besonderheiten transparenter oder transluzenter Kunststoffe erläutert werden, um den Nutzer für mögliche Probleme zu sensibilisieren. Im zweiten Teil werden Empfehlungen für Bestrahlung oder Bewitterung herausgearbeitet. In einem dritten Teil geht es dann um Besonderheiten bei der Messung von Eigenschaftsänderungen transparenter bzw. transluzenter Kunststoffe. In informativen Anhängen sollen verschiedene Beispiele die Thematik illustrieren. T2 - 51. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 29.03.2023 KW - Bewitterung KW - Polymer 3R KW - Bestrahlung KW - UV PY - 2023 SN - 978-3-9818507-8-9 SP - 39 EP - 46 PB - Gesellschaft für Umweltsimulation e.V. CY - Pfinztal (Berghausen) AN - OPUS4-57271 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Gorbushina, Anna A1 - Plarre, Rüdiger A1 - Stephan, Ina T1 - Umweltsimulation an der BAM – Grundlegende Ansätze mit Beispielen aus der natürlichen Umwelt N2 - Drei grundlegend verschiedene Ansätze für Umweltsimulation werden an Beispielen illustriert: (i) Ganzheitlicher Ansatz - Nachstellen von Umweltmilieus im Labor Ziel ist hier das Nachstellen von (kombinierten) Umweltbedingungen im Labor; die Umweltparameter werden mit all ihren Wechselwirkungen aufgebracht. Hauptnutzen ist eine gegenüber der natürlichen Beanspruchung erhöhte Reproduzierbarkeit der Umweltbedingungen. Hat man sein Laborsetup entwickelt, ist es auf verschiedene Materialien anwendbar. Unter solchen Laborbedingungen ermittelte Lebensdauern sind dabei nicht auf die typischerweise sehr variablen Real-Umweltbedingungen übertragbar. (ii) Parametrisierter Ansatz - Ermittlung einzelner Materialempfindlichkeiten Hierbei werden im Labor die Wirkungen separater Umweltparameter auf Materialien nachgestellt. Für eine solche Separation der Einflussfaktoren ist insbesondere die Aufschlüsselung möglicher Wechselwirkungen der Umwelt-parameter (z.B. Mikroklima an bestrahlten Oberflächen) erforderlich. Einzelne (meist Alterungs-) Empfindlichkeiten können qualitativ nachgewiesen werden oder sogar – als Beanspruchungs-Wirkungs-Funktionen – quantifiziert werden, was einen wesentlichen Schritt in Richtung der Digitalisierung der Material¬prüfung darstellt. Insbesondere ist dann auch eine Lebensdauer-vorhersage für vorgegebene Zeitreihen der Beanspruchungs¬parameter umsetzbar. (iii) Rückwirkungen auf die Umwelt Umweltbeanspruchungen können zur Freisetzung von Schadstoffen in die Umwelt führen. Durch die Nachstellung kritischer, aber realitätsnaher Einsatzszenarien kann die Menge an freigesetzten Substanzen abgeschätzt werden. Egal, welcher Ansatz verfolgt wird – ein Vergleich mit der oder einer Real-beanspruchung ist unerlässlich, ebenso wie die Messdatenaufzeichnung (data logging) aller potenziell relevanten Beanspruchungsparameter während dieser Realbeanspruchung. Obwohl die naturnahe Umwelt – sowohl in der BAM als auch bei der GUS – gegenüber der technischen Umwelt eher untergeordnet auftritt, werden zur Illustration Beispiele aus der naturnahen Umwelt verwendet. T2 - 50. Jahrestagung der GUS CY - Online meeting DA - 23.03.2022 KW - Umweltsimulation PY - 2022 SN - 978-3-9818507-7-2 SP - 79 EP - 89 AN - OPUS4-55015 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja T1 - Digitale Umweltsimulation am Beispiel der Photooxidation von Polymeren N2 - Die Umweltwirkungen auf ein Material werden als Überlapp der Funktionskurven von Materialempfindlichkeit und einwirkenden Umweltparametern betrachtet. Wenn entweder die Empfindlichkeit oder die Beanspruchungen Null sind, ergibt sich auch keine Umweltwirkung und bei beidseitig Werten größer Null das jeweilige Produkt der beiden. Die Akkumulation der nicht-reversiblen Effekte über die Zeit und allen Eigenschaftsänderungen entspricht der Alterung des Materials für den jeweiligen Expositionszeitraum. Die digitale Umweltsimulation gliedert sich hier in drei Teilaspekte. Ein erster, rein materialwissenschaftlicher Teil hat die Aufgabe, alle relevanten Materialempfindlichkeiten experimentell zu quantifizieren. Ein zweiter – unter Umständen numerischer Teil – hat die Aufgabe, das Bauteil und seine Einbaulage zu digitalisieren und aus den makroskopischen Umgebungsbedingungen die relevanten mikroklimatischen Umweltparameter für alle Oberflächen- oder Volumenelemente zu bestimmen. In einem dritten Teil werden die Einwirkungen über den betrachteten Zeitraum berechnet und kumuliert. Dieses Konzept, das auf den so genannten Expositions-Reaktions-Funktionen (ERF) basiert, wird an Beispielen der Photoxidation erläutert. Dieses Vorgehen wurde schon beim ViPQuali-Projekt als Numerische Umweltsimulation umgesetzt. Überprüft werden muss das Modell unbedingt an einer realitätsnahen Validierungsbeanspruchung. Hier werden die ermittelten ERFs mit über den kompletten Beanspruchungszeitraum geloggten Umweltparametern gekoppelt, um die berechnete mit der experimentell erfahrenen Alterungswirkung zu vergleichen. Nur so kann sichergestellt sein, dass alle für die Anwendungsumgebung relevanten Materialempfindlichkeiten einbezogen wurden. T2 - 52. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 26.03.2024 KW - UV KW - Polymer 3R KW - Bewitterung KW - Bestrahlung PY - 2024 SN - 978-3-9826129-0-4 SP - 31 EP - 40 PB - Gesellschaft für Umweltsimulation e.V. CY - Pfinztal (Berghausen) AN - OPUS4-59830 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bauer, J. A1 - Miclea, P.-T. A1 - Braun, U. A1 - Altmann, Korinna A1 - Turek, M. A1 - Hagendorf, C. T1 - Microplastic detection and analysis in water samples N2 - Microplastic detection in water samples becomes important for tracing microplastic sources. Microplastic may harm desalination facilities by blocking filters and disturbing the marine food chain. Thermo analytical methods such as pyrolysis gas chromatography mass spectroscopy, and spectroscopic methods like (micro) Raman spectroscopy or (micro) Fouriertransform infrared spectroscopy in combination with appropriate filters and sample preparation are suitable for analyzing microplastics on a scale from 1 µm to 1000 µm fast and unambiguous. While the thermo analytical methods are suitable for larger sample volumes, Raman spectroscopy and Fouriertransform infrared spectroscopy are able to detect and analyze single microplastic particles for instance in bottled water. Machine learning algorithms ensure a reliable classification of different plastic materials. T2 - International Conference on Sustainable Energy-Water-Environment Nexus in Desert Climate 2019 CY - Ar-Rayyan, Qatar DA - 02.12.2019 KW - Microplastics KW - Water samples PY - 2022 SP - 111 EP - 113 PB - Springer AN - OPUS4-56240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dittmann, Daniel A1 - Saal, L. A1 - Zietzschmann, F. A1 - Mai, M. A1 - Altmann, Korinna A1 - Al-Sabbagh, Dominik A1 - Ruhl, A. S. A1 - Jekel, M. A1 - Braun, U. T1 - Aktivkohlecharakterisierung als weiterer Schlüssel für Adsorptionsprognosen organischer Spurenstoffe in der vierten Reinigungsstufe N2 - In diesem Beitrag wird der Einfluss des Aktivkohleprodukts auf die Adsorption von Spurenstoffen aus Kläranlagenablauf gezeigt und diskutiert. Im zweiten Teil wird das Material Aktivkohle analytisch charakterisiert und die Eigenschaften systematisiert. Die gewonnenen Erkenntnisse werden mit Bezug zu Praxislösungen zusammengefasst. T2 - Wasser 2021 CY - Online meeting DA - 10.05.2021 KW - Aktivkohle KW - Thermogravimetrie KW - Zersetzungsgasanalyse KW - Proximatanalyse PY - 2021 SP - 373 EP - 378 AN - OPUS4-52740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus dem BAM-Fachbeirat N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. T2 - 22. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 10.03.2026 KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2026 SN - 978-3-00-085899-4 VL - 22 SP - 15 EP - 22 PB - HWTK Leipzig CY - Leipzig AN - OPUS4-65664 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid (HNO3) on HDPE jerrycans – comparison of outdoor and lab test N2 - A damaging action of HNO3-55% only occurs in combination with its decomposition into nitrous gases, which can be caused by UV radiation. In a laboratory test, transparent HDPE jerrycans have been exposed to both UV radiation and 55 wt-% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The respective damages are compared with FTIR spectroscopy in ATR and HT-gel permeation chromatography (GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. The gradual increase in oxidative damage shows the good reproducibility of the lab exposure. The decomposition of nitric acid into nitrous gases by UV radiation – as well as the jerrycan oxidation – is also observed at lower HNO3 concentration (28 wt- %). Similar results are obtained after outdoor tests. Again, the damage occurs only after combined exposure, in contrast to the exposures to UV only and to HNO3 only, which were conducted in parallel. Outdoor exposures are most readily accepted as they represent possible end-use conditions. However, the reproducibility of these exposures is poor due to the large temporal variations in weather. There are also several safety risks, which is why the number of replicates remains limited. Since the outdoor and lab exposure tests show the same qualitative results, it is appropriate to conduct systematic studies in the laboratory. After 6 days of lab exposure, the oxidation damage is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. It should be noted that this amount can also occur in two sunny weeks. T2 - 24th iapri World Packaging Conference CY - Valencia, Spain DA - 17.06.2024 KW - Ppolyethylene KW - UV exposure KW - Nitric acid KW - Oxidation PY - 2024 VL - 2 SP - 30 EP - 37 PB - ITENE AN - OPUS4-60414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kaminski, Katja A1 - Kluge, Stephanie A1 - Frenzel, Olivia A1 - Bücker, Michael A1 - Westphalen, Tanja ED - Ziegahn, Karl-Friedrich T1 - Entwicklung, Validierung und Anwendung eines beschleunigten Bewitterungsprotokolls zur Bewertung der Freisetzung von Bisphenol A (BPA) aus Polycarbonat (PC)-Materialien in die Umwelt N2 - BPA unterliegt einer kontinuierlichen behördlichen Kontrolle und ist als besonders besorgniserregender Stoff (SVHC) gelistet. Besondere Besorgnis besteht hinsichtlich seines häufigen Nachweises in Oberflächengewässern, obwohl es leicht biologisch abbaubar ist. In mehreren Studien wurden die Quellen und Wege von BPA in die Umwelt untersucht, wobei festgestellt wurde, dass seine Hauptverwendung als Monomer in PC nur marginal zu den BPA-Freisetzungen in die Umwelt über seinen Lebenszyklus beiträgt. Um die tatsächlichen Freisetzungen von BPA aus PC unter umweltrelevanten Bedingungen besser zu verstehen, wurde eine neu entwickelte Methodik (Bundesanstalt für Materialforschung und -prüfung, BAM) angewendet, die ein neuartiges beschleunigtes Bewitterungsprotokoll für Polycarbonat-Materialien in Kombination mit einem sensitiven Analysenverfahren umfasst, welches eine Bestimmung von BPA im Ultraspurenbereich ermöglicht. Das Bewitterungsprotokoll erreicht eine 13,6-fache Beschleunigung im Vergleich zu mitteleuropäischen Wetterbedingungen und simuliert Umweltstressoren (globale Strahlung, Regen, Temperaturschwankungen) in einer Bewitterungskammer, wobei gleichzeitig die BPA-Freisetzung mit einem validierten LC-MS/MS-Verfahren unter Verwendung einer organischen Isotopenverdünnungskalibrierung bestimmt wird. In parallelen Freilandversuchen wurden die Trübung und die Vergilbung („Yellowness-Index“) der zu untersuchenden Proben als Referenzparameter untersucht. T2 - 54. Jahrestagung der GUS 2026 CY - Blankenloch-Stutensee, Germany DA - 25.03.2026 KW - Polycarbonat KW - Bisphenol A KW - Bewitterung PY - 2026 SN - 978-3-9826129-3-5 VL - 54 SP - 139 EP - 153 AN - OPUS4-65793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -