TY - CONF A1 - Rosenbusch, Sjard Mathis T1 - Mesh-convergence and gradient-enhanced models in blast simulations of concrete structures N2 - Blast experiments on reinforced concrete structures are often limited to small structures and therefore simple shock waves. Such experiments are carried out at the Bundesanstalt für Materialforschung und -prüfung (BAM) and the structural response is investigated using several measuring methods. Complex load scenarios that occur as a result of reflection of the shock wave in larger structures are harder to realise in practice. Numerical simulations for the propagation of the shock wave and the structural response can therefore be an alternative method for the investigation of blast loads on complex structures. For the simulation of concrete under impact and blast loads, several local constitutive models exist that are formulated as plasticity models with softening taken into account by introducing a scalar damage field. Local damage models however often lead to mesh-dependent results which do not converge with mesh refinement. In order to achieve meaningful predictions from numerical experiments, independence from the mesh is needed. In this contribution, the JH2 model (Johnson and Holmquist 1994) with a parameter set for concrete is investigated in a simple blast load scenario. The shockwave is implemented as a simplified Friedlander-curve and the overpressures are applied as a boundary condition for the structural simulation. In order to account for large displacements that can occur during blast loads, an updated Lagrangian formulation is utilised. A Runge-Kutta method with adaptive time stepping is used to advance the solution in time. The open source FEM software FEniCS (Logg et al. 2012) is used together with an implementation of the JH2 model which has been developed at BAM. An extensive convergence analysis with both timestep- and mesh-refinement is carried out to show the mesh dependency. In order to make the results independent of the mesh, possible nonlocal versions of the JH2 model with gradient-enhancement are presented. Since many damage models for concrete share the damage mechanism of the JH2 model, the application of the regularisation methods to more complex material models, like the RHT model (Grunwald et al. 2017), is also discussed. Advantages of a gradient-enhanced formulation to simulate dynamic strength increase of concrete, as suggested in (Häußler-Combe and Kitzig 2009), is discussed as well. T2 - ECCOMAS YIC 2023 CY - Porto, Portugal DA - 19.06.2023 KW - Gradient-Damage KW - Explicit Dynamics KW - Concrete Modeling KW - Mesh Convergence PY - 2023 AN - OPUS4-58717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerbeit, Marco T1 - An apparatus for generating reproducible and scalable shock waves in the free field N2 - A simple test bench was set up on the BAM test site to investigate shock waves caused by gas detonations. The aim was to build a simple mobile test bench that can be used for various applications, to demonstrate the vaildity and for comparison with other test benches. For this purpose a balloon filled with acetylene and oxygen at atmospheric pressure with an electric ignitor was used. The characteristics of the shock waves can be scaled via the gaseous mixture, the filling quantity of the balloon and the distance to the sensors. Pressure sensors were set up around the balloon at various distances to measure the shock. With the help of the high-speed recordings and the Rankine Hugoniot equations, the shock front pressure was estimated and compared with the results of the pressure sensors. In order to validate the results of this test bench, they were compared with an experiment using plastic explosive no. 4 . These agreed well with the results. Overall, symmetrical undisturbed scalable shock waves can be generated with the setup. Only the reproducibility, which is comparatively poor to open shock tubes due to the influence of wind, had to be improved. T2 - 35th International Symposium on Shock Waves (ISSW35) CY - Brisbane, Australia DA - 07.07.2025 KW - Shock waves KW - BOS KW - Gas detonation PY - 2025 AN - OPUS4-63786 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit T1 - A Preliminary Study on the Scaling of RC Structures under Blasting Loading N2 - Current capabilities for full-scale field blast testing are highly resource intensive. Reliable small-scale experiments are an effective alternative. Characterization of the dynamic response and damage of RC elements to scaled blast loads was investigated in scaled-down field experiments. Spatially resolved information on the dynamic structural response to blast loading was obtained using distributed fiber optic acoustic sensing (DAS), acceleration sensors as well as piezoelectric pressure sensors. T2 - 46. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 25.04.2025 KW - Explosives KW - Blast and scaling effects KW - Concrete PY - 2025 AN - OPUS4-62994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Costard, René T1 - Charakterisierung der Belastung und Schädigung von Stahlbetonprüfkörpern unter Explosionsbeanspruchung N2 - Sprengversuche sind ein wesentliches Werkzeug, um die Eignung von Schutzobjekten und Bauteilen zum Schutz der Bevölkerung vor Anschlägen mit explosionsgefährlichen Stoffen wie Explosivstoffen, sogenannten „home-made-explosives“ (HME) und unkonventionellen Spreng- und Brandvorrichtungen (USBV) zu bewerten. Für forensische Zwecke werden oft Explosionsszenarien nachgebildet, um die Auswirkung von Anschlägen oder Unfällen genau untersuchen zu können. Feldversuche in Kombination mit numerischen Simulationen ermöglichen eine Charakterisierung der Belastung und Schädigung von Bauteilen und Strukturen unter hochdynamischen Explosionsbelastungen. Auf dem Testgelände Technische Sicherheit (TTS) der BAM in Horstwalde, Brandenburg werden Sprengversuche im Real-Maßstab durchgeführt. Dabei werden Bauteile mit Messtechnik ausgestattet, um eine dynamische Strukturcharakterisierung mittels sensorbasierten Monitorings zu ermöglichen. In diesem Vortrag werden am Beispiel einer Versuchskampagne mit einer Stahlbetonwand als Prüfkörper die Eignung verschiedener Prüfmethoden bei Sprengversuchen evaluiert. Es werden Messmethoden zur Charakterisierung der Explosionsereignisse, des globalen Strukturverhaltens sowie der lokalen Schädigung vorgestellt. Die direkte Charakterisierung der Explosionsbelastung erfolgt mit Hilfe von piezo-elektrischen Druckaufnehmern (bündig mit der Oberfläche im Prüfkörper montiert) und High-Speed-Kameras. Die Beobachtung der explosionsinduzierten Reaktion des Bauteils während und nach dem Eintreffen der Stoßwelle erfolgt mittels Beschleunigungssensoren, Stereo-Fotogrammetrie sowie mit in den Prüfkörper eingebetteter verteilter faseroptischer Sensoren, mit Hilfe derer die Dehnungsraten im Bauteil zeit- und ortsaufgelöst gemessen werden können. Die faseroptischen Sensoren erlauben außerdem die örtlich hochaufgelöste Bestimmung statischer Dehnungsänderungen im Bauteil nach einem Versuch, sodass auch nicht sichtbare Schädigungen wie kleinste Risse detektiert und charakterisiert werden können. Vergleichende Messungen mit Ultraschall komplettieren die Schadenscharakterisierung. In unserem Beitrag diskutieren wir die Herausforderungen dieser Messungen sowie die Ergebnisse und Möglichkeiten der genannten komplementären Messmethoden. T2 - 44. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 14.04.2023 KW - Explosivstoffe KW - Sprengversuche KW - Schädigungscharakterisierung KW - Sensorik PY - 2023 AN - OPUS4-57319 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit T1 - Numerical analysis of structures under blast loading N2 - Blast tests are indispensable for investigations of accidental or intentional explosions and to evaluate the level of protection to people and equipment within critical infrastructure. Current capabilities for detailed blast effects assessment are limited to performing full-scale field testing, which, for complex scenarios, are highly resource intensive. In this regard, reliable numerical simulations are an effective alternative option. A discussion of the scope and challenges of using numerical tools for a technical-safety assessment of reinforced concrete structures under blast loading is presented. Different coupling possibilities between shock wave simulations and structural simulations with the help of practical examples is given. An outlook on the development of new methods for structural simulations currently being researched at BAM concludes the presentation. T2 - Exerter Final Conference, 2023 CY - Soest, The Netherlands DA - 24.04.2023 KW - Coupling KW - Numerical Simulation KW - Blast KW - Structural Analysis KW - FSI PY - 2023 AN - OPUS4-57458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Costard, René T1 - Dynamic response of reinforced concrete (RC) components in scaled-down blast tests N2 - Der Beitrag präsentiert erste Ergebnisse aus dem BAM-internen Projekt AP5 Security zum Thema Charakterisierung der dynamischen Reaktion und Schädigung von Stahlbetonbauteilen. T2 - 44.Informationstagung Sprengtechnik CY - Siegen, Germany DA - 14.04.2023 KW - Explosionsbelastung auf Strukturen KW - Beton KW - Numerik PY - 2023 AN - OPUS4-57313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Costard, René A1 - Agasty, Amit A1 - Kadoke, Daniel A1 - Kind, Thomas A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - Charakterisierung der Belastung und Schädigung von Stahlbetonprüfkörpern unter Explosionsbeanspruchung N2 - Zur Bewertung der Widerstandsfähigkeit von Schutzobjekten und Bauteilen gegen Explosionsbeanspruchung führt die Bundesanstalt für Materialforschung und -prüfung (BAM) regelmäßig Sprengversuche im Realmaßstab auf einem Testgelände durch. Solche Versuche sind planungs- und ressourcenintensiv, sodass sie zunehmend durch numerische Simulationen ergänzt bzw. ersetzt werden. Aktuelle Forschungsarbeiten zielen darauf ab, neue Berechnungsmethoden und Materialmodelle zu entwickeln, mit denen die Bestimmung der Bauteilantwort sowie die daraus resultierende Schädigung nach einem Explosionsereignis möglich sind. Zur Validierung solcher Ansätze ist es notwendig, systematische Versuche mit unterschiedlichen Szenarien durchzuführen, bei denen die relevanten Parameter mit Hilfe verschiedener Messmethoden aufgezeichnet werden. T2 - 44. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 14.04.2023 KW - Explosivstoff KW - Explosionswirkung KW - Stahlbeton KW - Faseroptische Sensorik PY - 2023 SN - 0941 - 4584 VL - 45 IS - 2 SP - 11 EP - 14 AN - OPUS4-58109 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin A1 - Chruscicki, Sebastian A1 - Breithaupt, Mathias A1 - Costard, René A1 - Kind, Thomas A1 - Hüsken, Götz A1 - Agasty, Amit T1 - Measuring Dynamic Behavior and Damage Evolution of a Reinforced Concrete Wall Subjected to Explosive Blasts using Embedded Distributed Fiber Optic Sensors N2 - Results from highly dynamic and static strain measurements, respectively, using embedded distributed fiber optic sensors in a steel-reinforced concrete wall under explosive blast-loading are presented, detailing the structure’s dynamic behavior and the evolutions of cracks. T2 - 28th International Conference on Optical Fiber Sensors (OFS-28) CY - Hamamatsu, Japan DA - 20.11.2023 KW - Distributed acoustic sensing KW - DAS KW - Structural response KW - Blast experiment KW - Embedded fiber optic sensor PY - 2023 SP - 1 EP - 4 PB - Optica CY - Washington D.C., USA AN - OPUS4-59096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Costard, René T1 - Dynamic response of reinforced concrete (RC) components in scaled-down blast tests N2 - Current capabilities for full-scale field testing are highly resource intensive. Reliable small-scale experiments are an effective alternative. Characterization of the dynamic response and damage of RC elements to scaled blast loads was investigated in scaled-down field experiments. Spatially resolved information on the dynamic structural response using distributed fiber optic acoustic sensing (DAS) and acceleration as well as blast loading by piezoelectric pressure sensors. T2 - 45. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 05.04.2024 KW - Blast tests KW - Reinforced concrete KW - Acceleration sensors PY - 2024 AN - OPUS4-59808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lu, Xin A1 - Schukar, Marcus A1 - Weege, S. A1 - Roske, T. A1 - Krebber, Katerina T1 - Leakage detection at a borehole simulator using distributed acoustic sensing N2 - A distributed acoustic sensing system is used to detect the leakage in a borehole simulator by measuring the leakage induced vibration. The leakage location can be clearly determined by frequency spectrum analysis. T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Leakage detection KW - Structural health monitoring KW - Distributed fiber sensing KW - Distributed acoustic sensing PY - 2022 SP - 1 EP - 4 PB - Optica CY - Washington D.C., USA AN - OPUS4-56097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Bernauer, F A1 - Igel, H A1 - Hadziioannou, Céline T1 - Wave-Screening Methods for Prestress-Loss Assessment of a Large-Scale Post-Tensioned Concrete Bridge Model Under Outdoor Conditions N2 - This paper presents advancements in structural health monitoring (SHM) techniques, with a particular focus on wave-screening methods for assessing prestress loss in a large-scale prestressed concrete (PC) bridge model under outdoor conditions. The wave-screening process utilizes low-frequency wave propagation obtained from seismic interferometry of structural free vibrations and high-frequency wave propagation obtained through ultrasonic transducers embedded in the structure. An adjustable post-tensioning system was employed in a series of experiments to simulate prestress loss. By comparing bridge vibrations under varying post-tensioning forces, the study investigated prestress loss and examined temperature-related effects using the coda wave interferometry (CWI) method. Local structural alterations were analyzed through wave velocity variations, demonstrating sensitivity to bridge temperature changes. The findings indicate that wave-based methods are more effective than traditional modal analysis for damage detection, highlighting the dual impacts of prestress loss and temperature, as well as damage localization. This study underscores the need for long-term measurements to account for temperature fluctuations when analyzing vibration measurements to investigate changes in prestressing force in PC structures. KW - Coda wave interferometry KW - Damage detection KW - Prestress loss KW - Seismic interferometry KW - SHM KW - Temperature influence KW - Ultrasonics KW - Wave-screening PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634244 UR - https://www.mdpi.com/2076-3417/15/11/6005 DO - https://doi.org/10.3390/app15116005 VL - 15 IS - 11 SP - 1 EP - 18 PB - MDPI AN - OPUS4-63424 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerbeit, Marco T1 - Background oriented Schlieren measurements for pressure relief systems in the free field N2 - Shock waves or shocks are a supersonic phenomenon in which the flow variables change abruptly in a thin layer. These occur with super sonic flow, such as the supersonic flight of airplanes or rockets or with explosions. As the pressure, temperature and density change in a shock, this can be recorded. The most commonly used approach is the use of pressure sensors. Pressure information is only available at the certain locations where the sensors are installed. Any body, such as free-standing sensors, that is introduced into the flow, distorts it. Therefore, not inverse measurement methods for measuring flow variables, such as the background orientated schlieren (BOS) method or the partical image velocimetry (PIV), are used. For this reason, a BOS setup was carried out in an open field at the Test Site Technical Safety (TTS) of BAM using a shock wave generator to visualize the shocks that result from a gas explosion. These investigations are presented in this paper. The aim is also to draw conclusions about the pressure change caused by the shock and the advantages that such a simple structure provides to the tests. T2 - 30th International Colloquium on the Dynamics of Explosions and Reactive Systems CY - Ottawa, Canada DA - 28.07.2025 KW - BOS KW - Blast KW - Shock PY - 2025 AN - OPUS4-63915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Soruco Aloisio, Ricardo T1 - Digitale Abbildung von Assets - Dateninfrastruktur für Industrie 4.0 N2 - Im Rahmen der von der BAM und anderen Partnern ins Leben gerufenen Initiative „Digitale Qualitätsinfrastruktur“ liegt der Fokus u.a. auf der Entwicklung von neuen Zertifizierungsworkflows. Dabei ist eine besondere Bedeutung dem Zusammenführen von Operational Technology (OT) und Informationstechnik (IT) beizumessen. Zur Datenintegration aus der Sensor-Feldebene einer Versuchs-Wasserstofftankstelle wurde eine solche Infrastruktur aufgebaut. Zudem wurde der von der Plattform Industrie 4.0 empfohlene standardisierte Zwilling „Verwaltungsschale“ für einige Assets der Wasserstofftankstelle implementiert. T2 - QI-Forum 2024 CY - Berlin, Germany DA - 09.10.2024 KW - Datenintregration KW - IT KW - Infrastruktur KW - OT KW - Open Source KW - Software KW - VPN KW - Verwaltungsschale PY - 2024 AN - OPUS4-63493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klaus, Christian T1 - QI Digital: Cross-Location IT Infrastructure and Asset Administration Shell as a Digital Twin N2 - Im Rahmen der von der BAM und anderen Partnern ins Leben gerufenen Initiative „Digitale Qualitätsinfrastruktur“ liegt der Fokus u.a. auf der Entwicklung von neuen Zertifizierungsworkflows. Dabei ist eine besondere Bedeutung dem Zusammenführen von Operational Technology (OT) und Informationstechnik (IT) beizumessen. Zur Datenintegration aus der Sensor-Feldebene einer Versuchs-Wasserstofftankstelle wurde eine solche Infrastruktur zunächst in einer Laborumgebung aufgebaut. Dieser Vortrag beschreibt die Implementierung des standardisierten und von der Plattform Industrie 4.0 empfohlenen digitalen Zwillings "Verwaltungsschale" an dieser Wasserstofftankstelle. Außerdem wird die Implementierung einer standortübergreifenden IT-Infrastruktur über VPN/5G beschrieben. T2 - BAM Kolloquium Abteilung 1 CY - Berlin, Germany DA - 10.06.2025 KW - Datenintregration KW - IT KW - Infrastruktur KW - OT KW - Open Source KW - Software KW - VPN KW - Verwaltungsschale PY - 2025 AN - OPUS4-63495 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel T1 - Einsatz von Körpermnodellen bei der Auswirkungsbetrachtung auf das "System Mensch" N2 - In diesem Vortrag werden aktuelle Arbeiten der BAM zu Auswirkungsbetrachtungen bei Stoff- und Energiefreisetzungen mit Zielstellung der Erfassung und Beurteilung der Einwirkungen auf den Menschen vorgestellt. T2 - 3. DUMMY.CRASHTEST.KONFERENZ. CY - Münster, Germany DA - 20.06.2023 KW - Auswirkungsbetrachtung KW - Dummy KW - Körpermodell PY - 2023 AN - OPUS4-57747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik T1 - Investigation of Shock Wave Propagation in Soft Tissue Simulants: An Analysis of Organic Gelatin and Synthetic Gel N2 - This study investigates the effects of shock waves on soft tissue simulants, focusing on organic gelatin and a synthetic gel. Although extensive research has focused on the mechanical properties of soft tissue simulants, their behavior under shock wave conditions, such as those caused by blasts, is less understood. As explosives are increasingly used in modern combat scenarios, it is essential to study how shock waves interact with soft tissue. This knowledge is crucial for improving protective equipment and evaluating blast effects on the human body. A two-phase methodology was applied: First, organic gelatin production and synthetic gel composition were analyzed, identifying uncertainties and measuring sound speeds at varying temperatures to align with human tissue properties. Second, simulants were subjected to free-field shock waves, and embedded pressure sensors captured wave propagation, peak overpressures, and propagation velocity. Findings provide comparative insights into shock wave responses of simulants, offering a foundation for future experimental setups. KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Druckwelle PY - 2025 SN - 9781605956978 VL - 34 SP - 63 EP - 79 PB - DEStech Publications Inc. CY - USA AN - OPUS4-63320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik A1 - Grobert, Steffen A1 - Krentel, Daniel T1 - Description of a measurement setup for the combined measurement of LLB exposures in dynamic situations using high-resolution measurement technology N2 - In order to gain an understanding of the Low Level Blast (LLB) exposure of soldiers when using weapon systems, it is necessary to characterize these weapon systems with regard to their overpressure effect [1]. Carrying out static measurements of weapon systems in the rough terrain of firing ranges and training areas poses a challenge for sensitive measurement technology. Furthermore, soldiers are often exposed to LLB in dynamic situations [2]. Therefore, commercially available blast gauges are often used, which, however, are not sufficient for high-resolution measurement of overpressure exposures with academic requirements due to their intended use [3]. Static measurement setups, such as with penile probes, must be used to characterize weapon systems, but they cannot make valid statements about the real load on dynamically behaving soldiers. However, this real load on the soldier is essential in order to be able to adequately assess the potential resulting medical effects. As part of this challenging measurement task, a prototype of a self-sufficient, high-resolution measurement system is presented, which can be used by an operator in dynamic situations without interference. The complete measuring chain was realized as a self-sufficient unit. The system is based on a 20-liter backpack system, which contains the power supply, the measuring amplifier and the measuring card. The measuring computer is attached to the front of the backpack to allow quick access. The measuring system is capable of recording four channels with a sampling rate of up to 2 MHz. Piezoelectric integrated charge pressure sensors are used as a high-resolution pressure sensor (type: PCB138B32). The pressure sensor is placed on a XX- carrier plates with the dimensions XY × YY. The pressure sensors are attached at the typical positions for Blast-Gauges measurements, like on the left shoulder, on the upper chest and on the back of the head. At the same time, commercial blast gauges are placed at the positions of the pressure sensors to qualify the blast gauges (type: B3 Blast Gauges Gen 6). The measuring system is referred to as a “Sensor Carrier Operator (StEk)”. As part of the functional testing of the measurement system, tests are carried out with hand weapons. For this purpose, a soldier is equipped with the StEk and blast gauges. The handguns used are the pistole P8 (caliber 9 mm) and the long rifle G36 (caliber 5.56 mm). The firing position is standing freehand. In addition, the soldier carried out an examination of the carrying comfort of the StEk as part of the training. Furthermore, it was evaluated whether the measuring chain was adequately integrated into the measuring system. The quality of the pressure measurement was also examined, whereby a direct comparison was made with the blast gauges. The measurement system presented here enables the combined (static and dynamic) scientific characterization of weapon systems, particularly with regard to overpressure loading. T2 - Research Specialist Meeting HFM 371 (NATO STO) CY - Toronto, Canada DA - 09.04.2025 KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Low Level Blast PY - 2025 SP - 1 EP - 8 AN - OPUS4-63322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik T1 - Use of the shockwave generator for research on low-level blast effects - Monitoring vs. measurement tools N2 - In order to contribute to the research efforts on primary explosion effects, an experimental setup was created to generate realistic overpressure load cases under the most reproducible conditions and with short setup times. One focus of the project is now the applicability of this test setup for Low Level Blast (LLB) testing [1-3]. The basis of our experimental setup is the Shockwave Generator (SWG), which has already been presented in detail [4]. In addition, a stand-alone measurement system has been developed that can be worn by the operators who are exposed to LLB. The measuring system is referred to as the ´Sensor Carrier for Operator´ (StEk; German abbr.: Sensortraeger Einsatzkraft). With the StEk, it is possible to record LLB exposures in training scenarios with a measuring accuracy satisfying scientific requirements and thus to classify the corresponding LLB load case of the respective weapon system or training scenario. In the test series presented here, the StEk was attached to an operator dummy and exposed to an overpressure load case. The results of the StEk were compared with a pencil probe (PP), which was positioned symmetrically to the StEk in the undisturbed blast propagation area of the SWG. The aim of the test series was to compare the accuracy of the self-sufficient measurement setup StEk with the conventional pressure measurement method (PP). Conventional, market-available blast exposure monitoring device (BEMD) (type: B3 Blast Gauges Gen.6) were used in parallel to check their accuracy. Setup & Method The experimental setup is shown in Figure 1 (left). The StEk system was attached to a dummy placed at a 45° angle to the SWG pressure outlet at a distance of 1 m. A PP was placed axially mirrored. The sensors of the StEk were placed in the typical positions for BEMD. With reference to the incident shockwave, one sensor was placed on the chest (face-on) and one on the shoulder (side-on). The BEMDs were also placed in the same positions. The standalone StEk measurement system is described in the following. The complete measuring chain was realized as one stand-alone, self-sufficient unit. The system is based on a 20-liter backpack system, which contains the power supply, the measuring amplifier and the data acquisition system (DAQ) (Figure 1 (right)). The amplifier has four channels, an integrated 50 kHz low pass filter and is suitable for use with integrated charge piezoelectric (ICP) pressure sensors. A sampling rate of up to 2 MHz can be used Data is stored in a buffer of 64 MS. The computer, a Tablet PC, is attached to the front of the backpack to allow quick access. The pressure sensors are connected to the BNC interfaces on the outside of the housing using coiled BNC cables. The coiled BNC cables allow maximum freedom of movement and reduce mechanical stress on the couplings. In the current configuration, up to four ICP pressure sensors can be mounted on the operator (type: PCB132B38). The pressure sensors are flush-mounted in a 30 mm × 30 mm carrier plate. Results & Discussion Figure 2 (a) shows the overpressure generated by the SWG measured with the PP. The idealized pressure curve can be seen. The second peak is a reflection that occurs within the SWG. Figure 2 (b) shows the pressure measured by the BEMDs. It can be seen that both pressure curves correspond approximately to the idealized pressure curve. This is remarkable because the chest sensor was facing forward and should have a dynamic pressure component caused by the movement of the gas [5]. However, the pressure curves in Figure 2 (b) show the idealized pressure curve that should occur with a side-on overpressure measurement in the undisturbed free field. Therefore, it can be assumed that software modeling is used to generate an idealized pressure curve from the blended pressure curve that is intended to represent the overpressure that will occur. Figure 2 (c) shows the pressure curves of the ICP pressure sensors of the StEk system. It can be seen that the characteristics of the pressure curves were affected by the dynamic pressure component. The shoulder sensor, which, due to the nature of the dummy posture and position, was not exposed perfectly side-on, also showed a dynamic component. Calculations based on the peak overpressures of the PP confirm, that the reflected pressure was visible on the face-on chest sensor [5]. A limiting factor is that the sensor mounts and the dummy itself are subject to mechanical excitation, which probably explains the interference frequency seen in the pressure signal. The test results show the limitations of BEMDs for scientific investigations of weapon systems, as it is assumed that a high degree of modeling of the pressure curves takes place during post-processing. However, as the comparison of the BEMDs with the PP pressure curves shows, the pressure curve fit matches the PP pressure curve sufficiently well. This shows that a scientific measurement system such as StEk should be used initially to investigate and assess the load case from weapon systems or training scenarios in order to capture the real and complete characteristics of the load case. T2 - 8th International Forum on Blast Injury Countermeasures CY - Tokio, Japan DA - 07.05.2025 KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Low Level Blast PY - 2025 AN - OPUS4-63318 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik T1 - Description of a measurement setup for LLB exposures in dynamic situations using high-resolution measurement technology N2 - In order to gain an understanding of the Low Level Blast (LLB) exposure of soldiers when using weapon systems, it is necessary to characterize these weapon systems with regard to their overpressure effect [1]. Carrying out static measurements of weapon systems in the rough terrain of firing ranges and training areas poses a challenge for sensitive measurement technology. Furthermore, soldiers are often exposed to LLB in dynamic situations [2]. Therefore, commercially available blast gauges are often used, which, however, are not sufficient for high-resolution measurement of overpressure exposures with academic requirements due to their intended use [3]. Static measurement setups, such as with penile probes, must be used to characterize weapon systems, but they cannot make valid statements about the real load on dynamically behaving soldiers. However, this real load on the soldier is essential in order to be able to adequately assess the potential resulting medical effects. As part of this challenging measurement task, a prototype of a self-sufficient, high-resolution measurement system is presented, which can be used by an operator in dynamic situations without interference. The complete measuring chain was realized as a self-sufficient unit. The system is based on a 20-liter backpack system, which contains the power supply, the measuring amplifier and the measuring card (see Fig. 1, left). The measuring computer is attached to the front of the backpack to allow quick access. The measuring system is capable of recording four channels with a sampling rate of up to 2 MHz. Piezoelectric integrated charge pressure sensors are used as a high-resolution pressure sensor (type: PCB138B32). The pressure sensor is placed on a XX- carrier plates with the dimensions XY × YY. The pressure sensors are attached at the typical positions for Blast-Gauges measurements, like on the left shoulder, on the upper chest and on the back of the head. At the same time, commercial blast gauges are placed at the positions of the pressure sensors to qualify the blast gauges (type: B3 Blast Gauges Gen 6). The measuring system is referred to as a “Sensor Carrier Operator (StEk)”. As part of the functional testing of the measurement system, tests are carried out with hand weapons. For this purpose, a soldier is equipped with the StEk and blast gauges. The handguns used are the pistole P8 (caliber 9 mm) and the long rifle G36 (caliber 5.56 mm). The firing position is standing freehand. In addition, the soldier carried out an examination of the carrying comfort of the StEk as part of the training. Furthermore, it was evaluated whether the measuring chain was adequately integrated into the measuring system. The quality of the pressure measurement was also examined, whereby a direct comparison was made with the blast gauges (see Fig. 1 right). The measurement system presented here enables the combined (static and dynamic) scientific characterization of weapon systems, particularly with regard to overpressure loading. T2 - Research Specialist Meeting HFM 371 (NATO STO) CY - Toronto, Canada DA - 09.04.2025 KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Low Level Blast PY - 2025 AN - OPUS4-63323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik T1 - Investigation of Shock Wave Propagation in Soft Tissue Simulants: An Analysis of Organic Gelatin and Synthetic Gel N2 - This study investigates the effects of shock waves on soft tissue simulants, focusing on organic gelatin and a synthetic gel. Although extensive research has focused on the mechanical properties of soft tissue simulants, their behavior under shock wave conditions, such as those caused by blasts, is less understood. As explosives are increasingly used in modern combat scenarios, it is essential to study how shock waves interact with soft tissue. This knowledge is crucial for improving protective equipment and evaluating blast effects on the human body. A two-phase methodology was applied: First, organic gelatin production and synthetic gel composition were analyzed, identifying uncertainties and measuring sound speeds at varying temperatures to align with human tissue properties. Second, simulants were subjected to free-field shock waves, and embedded pressure sensors captured wave propagation, peak overpressures, and propagation velocity. Findings provide comparative insights into shock wave responses of simulants, offering a foundation for future experimental setups. T2 - 34th International Symposium on Ballistics CY - Jacksonville, FL, USA DA - 19.05.2025 KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Druckwelle PY - 2025 AN - OPUS4-63321 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Grasse, Dennis A1 - Seeber, H. T1 - Mild Traumatic Brain Injury - Current Research Works in the Field of Primary Blast Injury N2 - In this presentation, the team security research of division 2.1 informs about current research efforts in the field of traumatic brain injury. The focus lies on the consequences of low-level blast on the human brain. Also the general research approaches of the team for the investigation of the behaviour of shock waves within human tissues are presented. T2 - ATLAS ENTRY Seminar CY - Göppingen, Germany DA - 21.08.2023 KW - LLB KW - Blast KW - mTBI KW - Primary blast injury KW - Traumatic brain injury PY - 2023 AN - OPUS4-58130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeber, Henrik A1 - Grobert, Steffen T1 - Investigation of intracorporeal shock wave propagation using a simplified torso model and a shock wave generator N2 - Blast injuries are among the most common injuries in military operations. Also, in civilian environments, more explosive threats are expected in the future due to emerging conflicts and threats. While the effect of fragments, which is classified as secondary blast injury, could be minimized by police and military personnel’s modern ballistic body protection systems, the effects of shock wave propagation in the body as part of the primary explosion trauma still remain a serious threat needing further research. The detonation-physical processes of highly dynamic pressure changes within the human body, the reflection-related amplification of shock waves at organ-dermis interfaces, and the consequences of injury mechanisms have become more prominent in international research. Various approaches have been used to investigate these aspects. Animal experiments on free field test sites or shock tube setups combined with a subsequent biological evaluation and numerical simulations provided promising results and allowed the discussion of different biomechanical aspects. However, due to poor reproducibility and a lack of short-term dynamic material properties, most research approaches have significant limitations. Laboratory test setups do not represent real-scale high explosive detonation parameters with regards to pressure characteristics, impulse duration and blockage problems. Measured values are interpreted with partly outdated, selective and not validated limit values for overpressures from field tests with animals. This is due to the lack of a validated and comprehensive data set covering a variation of the crucial parameter. Injury mechanisms and their effects have not yet been sufficiently elucidated for the torso and extremities. In order to contribute to the research efforts on the primary explosion effects, the German Federal Armed Forces established an interdisciplinary military medical research project in cooperation of the Bundeswehr Hospital Berlin and the German Federal Institute for Materials Research and Testing (BAM). The aim of the planned investigation is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times. T2 - 7th International Forum on Blast Injury Countermeasures CY - Tokio, Japan DA - 17.05.2023 KW - Shock wave generator KW - Blast injury KW - Primäre Explosionswirkung KW - Experimental setup PY - 2023 AN - OPUS4-60045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grobert, S. T1 - Development of a body model and a shock wave generator for the analysis of intracorporeal shock wave propagations after explosions N2 - Im Rahmen dieses Vortrags wurden die ersten Ergebnisse des Sonderforschungsprojektes " Entwicklung und Validierung eines Körpermodells und eines Stoßwellengenerators zur Simulation der intrakorporalen Stoßwellenausbreitung nach Explosionen", welches in Zusammenarbeit zwischen dem Bundeswehrkrankenhaus Berlin und der BAM durchgeführt wird, vorgestellt. Der Versuchsaufbau (Stoßwellengenerator) und die verwendete Sensorik werden dargestelt, sowie eine vergeichende Studie zu den Protypen der Körpermodellen und Simulanzien. T2 - Kick-off-Workshops der NATO-Gruppe HFM 338 "Development of military loading exposure guidelines for prevention of chronic traumatic encephalopathy" CY - Online meeting DA - 18.05.2021 KW - Auswirkungsbetrachtungen KW - Blast KW - Explosionsverletzung PY - 2021 AN - OPUS4-53540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Thomas A1 - Máca, Petr A1 - Hering, Marcus A1 - Fiedler, Georg A1 - Beckmann, Birgit T1 - Impact Experiments on Reinforced Concrete Specimens - Investigation of Repeatability and Scaling N2 - Nowadays, the impact resistance of concrete structures has become a prominent concern for critical infrastructure operators, particularly amidst escalating geopolitical tensions. Regulators and design engineers know that reinforced concrete structures can only be developed with high efficiency by considering nonlinear structural and highly nonlinear material behavior. Therefore, specific guidelines on impact design provide instructions for design and analysis of structures required to resist impact loading. These instructions are usually based on published results and evaluated data of impact experiments carried out in laboratories. To widen the knowledge and increase the scientific data the Institute of Concrete Structures (IMB) at TUD Dresden University of Technology (TUD) has carried out many impact experiments on reinforced concrete specimens in recent years. A specially designed drop tower is available for this purpose on the premises of the Otto Mohr Laboratory, TUD. In the framework of the past research at TUD some important issues, such as influence of rebar arrangement, structural thickness, scalability of specimen and repeatability, with regard to experimental impact testing were investigated. This article presents the drop tower facility and research results of impact experiments on reinforced concrete slabs. First, the scalability of impact experiments will be discussed in conjunction with already known theoretical scaling parameters provided by researchers in the past, e.g. Rüdiger et al. [1]. Scalability of experimental data is of huge importance since protective structures made of reinforced concrete differ usually in size in comparison to experimental specimens. The second important research focus is on repeatably of impact experiments. Since impact experiments are usually time consuming and expensive, a certain impact scenario is mostly carried out only once. It is intended to show the range of deviation of impact tests on some already carried out experiments on reinforced concrete slabs. A possible standard deviation is estimated for the applied test setup. T2 - 15th International Conference on Shock & Impact Loads on Structures CY - Gothenburg, Sweden DA - 12.06.2025 KW - Reinforced concrete KW - Drop-weight impact KW - Scaling KW - Repeatability KW - Digital image correlation PY - 2025 SP - 80 EP - 91 AN - OPUS4-63627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bell, Jérémy T1 - Embedded sensor for the detection of TNT in surface and marine waters N2 - In 1945, the Potsdam Conference led to the decision to destroy a significant amount of ammunition from the warring parties of WWII. Dumping was considered the cheapest, quickest, and safest solution to dispose of unused ammunition. However, thin barrels or containers often leak after 50 years, allowing explosives to escape into the marine environment. As the effects of weapons chemicals on ecosystems are well-documented, it is becoming increasingly important to detect, recover and dispose of old ammunition. Physical techniques such as magnetometry and sonar are used to detect ammunition in the sea, but they do not provide chemical information. Detecting leaking organic contaminants like TNT or other explosives in water or soil requires high-end laboratory equipment like HPLC or GC-MS, making remote water testing virtually impossible. As an alternative, a miniaturized method for the selective and sensitive indication of TNT using fluorescence light-up sensing was developed. The visual identification of TNT with a nucleophile that forms a strongly absorbing charge transfer complex (CTC) is a well-known method. This CTC is formed by the attraction of an electron from the donor molecule by the electron-deficient aromatic ring. In this work, a TNT-based CTC was selectively formed by the addition of tetraoctylammonium acetate in N,N-diethylformamide and, as expected, showed strong absorption. Surprisingly, at room temperature, the CTC can be converted into a fluorescent product with an emission band centred at 577 nm. For the detection of TNT in water, a microfluidic chip made of polydimethylsiloxane (PDMS) is used for both the extraction and reaction steps. In addition to miniaturising the experimental steps, the optical system (fluorometer) has been integrated into an autonomous smartphone assembly capable of catalysing the photoreaction and analysing the fluorescence response. Taking advantage of the light-up response, TNT was still easily detectable down to 9.4 ng with the CMOS camera. Further evaluation of this analytical tool consisted of analyses of unfiltered and untreated surface water samples spiked directly with increasing concentrations of TNT to reflect different levels of contamination. LODs of 21 and 40 ng were found for samples from the Teltow Canal in Berlin (DEU) and the Baltic Sea near Greifswald (DEU). Such an analytical tool could be used to monitor water quality in the field, as the release of organic pollutants from munitions into surface and marine waters will become increasingly problematic and concentrations will continue to rise over the coming decades. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Explosives KW - Microfluidics KW - Smartphone KW - Sprengstoffe KW - Mikrofluidik KW - Sensor PY - 2025 AN - OPUS4-62767 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rurack, Knut T1 - Empowering test strips for rapid, highly sensitive and multiplexed analysis of small molecule analytes at a point-of-need N2 - In particular, the rapid development of lateral flow assays as indispensable tools for everyone to contain the SARS-CoV-2 pandemic has fuelled the global demand for analytical tests that can be used outside dedicated laboratories. In addition to their use in medical diagnostics, rapid tests and assays have become increasingly important in various fields such as food safety, security, forensics, and environmental management. The advantage is obvious: taking the assay directly to the sample minimizes the time between suspicion and decision-making, allowing faster action. Especially today, when mobile communication devices with powerful computing capabilities and built-in cameras are ubiquitous, more people than ever before around the world have the basic skills to operate a powerful detector at their fingertips. This sets the stage for a much wider use of analytical measurements in terms of prognosis and prevention, enabling professional laypersons in particular. However, current strip-based systems are primarily focused on single parameter analysis, whether it is SARS-CoV-2 biomarkers, blood glucose levels, or lead concentrations in water samples. Industrial applications of such methods also often still rely on single-parameter assays, requiring multiple runs even for a limited number of key parameters. Overcoming these limitations depends on developing low-number multiplexing strategies that ensure robustness, reliability, speed, ease of use, and sensitivity. This lecture will give an overview of several generic approaches developed in recent years to address these challenges. It will highlight how the synergy of supramolecular (bio)chemistry, luminescence detection, hybrid (nano)materials and device miniaturization can result in powerful (bio)analytical assays that can be used at a point-of-need.1-5 Selected examples will introduce key aspects of such systems that include tailored signaling mechanisms and recognition elements, materials functionalization and device integration, including hybrid nanomaterials, gated indicator release systems, strip modification, and smartphone-based analysis. T2 - 15th Rapid Methods Europe Conference CY - Amsterdam, Netherlands DA - 06.11.2023 KW - Test strips KW - Lateral flow assays KW - Explosives KW - Pesticides KW - Rapid testing KW - Multiplexing PY - 2023 AN - OPUS4-58816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Biyikal, Mustafa A1 - Rurack, Knut T1 - Development of a Lab-on-a-Chip for the Detection of Nerve Agents with a Handheld Device N2 - The development of a Lab-on-a-Chip (LoC) is presented, which can detect reactive phosphorous compounds in the gas phase in combination with an optochemical hand-held sensor. The LoC prototype contains three pairs of sensing materials containing fluorescent indicator dyes in various carrier materials. By measuring the fluorescence response to phosphoryl chloride, a surrogate compound, the detection of chemical warfare agents (CWAs) in gas phase becomes possible within seconds, introducing a novel approach to CWA detection. T2 - 2023 IEEE SENSORS Conference CY - Vienna, Austria DA - 29.10.2023 KW - Lab-on-a-Chip KW - Nerve agents KW - Hand-held KW - Fluorescence KW - Toxic industrial chemicals PY - 2023 UR - https://ieeexplore.ieee.org/document/10325263 SN - 979-8-3503-0387-2 DO - https://doi.org/10.1109/SENSORS56945.2023.10325263 SP - 1 EP - 4 PB - IEEE CY - New York AN - OPUS4-59367 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bell, Jérémy A1 - Biyikal, Mustafa A1 - Rurack, Knut T1 - Embedded sensor based on tandem smartphone-microfluidic device for the detection of TNT in surface and sea waters N2 - The globe's seas were used as dumping ground after the world wars and those millions of ammunition, most of all containing 2,4,6-trinitrotoluene (TNT), represent a pressing danger for fishermen, dredging operations, submarine cable installations and tourism. We developed an extremely selective indication method for TNT based on a specific reaction that produces a highly fluorescent compound. The indication system was integrated into a microfluidic PDMS chip for the solid-liquid extraction of TNT from water samples, offering environmental monitoring possibilities. Combining the advantages of a light-up indicator, microfluidics and a smartphone as detector, the embedded sensor allows for the remote and rapid detection of TNT down to ng in surface and sea waters. T2 - µTAS 2020 CY - Online meeting DA - 05.10.2020 KW - Smartphone KW - Rapid test KW - TNT KW - Ammunition KW - Schnelltest KW - Munition PY - 2020 AN - OPUS4-51444 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rurack, Knut T1 - Development of a Lab-on-a-Chip for the Detection of Nerve Agents with a Handheld Device N2 - The development of a Lab-on-a-Chip (LoC) is presented, which can detect reactive phosphorous compounds in the gas phase in combination with an optochemical hand-held sensor. The LoC prototype contains three pairs of sensing materials containing fluorescent indicator dyes in various carrier materials. By measuring the fluorescence response to phosphoryl chloride, a surrogate compound, the detection of chemical warfare agents (CWAs) in gas phase becomes possible within seconds, introducing a novel approach to CWA detection. T2 - IEEE Sensors Conference CY - Vienna, Austria DA - 29.10.2023 KW - Chemical warfare agents KW - Lab-on-a-chip KW - Handheld sensors KW - Toxic industrial chemicals KW - Fluorescence PY - 2023 AN - OPUS4-58815 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pauli, Jutta A1 - Ramírez, A. A1 - Crasselt, C. A1 - Schmidt, W. A1 - Resch-Genger, Ute T1 - Utilizing optical spectroscopy and 2',7'-difluorofluorescein to characterize the early stages of cement hydration N2 - The increasingly sophisticated nature of modern, more environmentally friendly cementitious binders requires a better understanding and control particularly of the complex, dynamic processes involved in the early phase of cement hydration. In-situ monitoring of properties of a constantly changing system over a defined period of time calls for simple, sensitive, fast, and preferably also non-invasive methods like optical spectroscopy KW - Flourescence KW - Optical probe KW - Sensor KW - Dye KW - Flourescin KW - Photophysics KW - PH KW - Quantum yield KW - Quality assurance KW - Mechanism KW - Cement KW - Concrete KW - Building material KW - Hydration KW - Process monitoring PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-537176 DO - https://doi.org/10.1088/2050-6120/ac2da0 SN - 2050-6120 VL - 10 IS - 1 SP - 2 EP - 13 PB - IOP Science AN - OPUS4-53717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit T1 - Assessment of the Application of Scaling Concepts for Blast Effects Analysis N2 - Blast testing finds its implementation in several applications, e.g. for the purpose of investigation into accidental or intentional explosions, or for an assessment of the level of protection provided by a certain structural configuration. Analytical and/or semi-empirical methods are generally limited to preliminary assessments prior to blast testing. Applications of numerical simulations with hydrocodes coupled with finite element methods (FEM) can only reduce the amount of blast testing required, as these necessitate fulfillment of the fundamental prerequisites of model verification and that of model validation. Field tests are implemented for contact detonations as well as near-field blast scenarios and shock tube tests for far-field blast scenarios. However, these can be extremely resource intensive. Reliable small-scale experiments are a promising alternative. The concepts of dimensional analysis and similarity based on Buckingham’s Π-theorem (1914) have been applied in different fields. For applications to the phenomenon of shock wave propagation, Hopkinson-Cranz or cube-root scaling is a well-established concept. When it comes to scaling the structural response, research has predominantly focused on structures made of metallic materials. Scaled investigations with concrete or reinforced concrete (RC) structures remain limited. The lack of even the most basic guidelines (far from any ‘standardized scaling methods’ for blast tests) show that scaling as a method is not yet established in blast effects analysis. In this preliminary study, we present a systematic approach and evaluation of scaling of blast effects analysis for RC slabs in order to develop guidelines for resource efficient testing methods. We study the blast scenario at two different scales. The focus of these investigations has been on evaluation of scaling of dynamics using pressure sensors, acceleration sensors and fiber optic sensing cables for distributed acoustic sensing (DAS). Further, the resulting plastic behavior upon blast is characterized by distributed strain sensing (DSS) along the same cables. T2 - 27th International Symposium on Military Aspects of Blast and Shock (MABS27) CY - Colmar, France DA - 06.10.2025 KW - Blast KW - RC-slabs KW - Similarity and scaling PY - 2025 AN - OPUS4-64616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Costard, Rene A1 - Hering, Marcus A1 - Chruscicki, Sebastian A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - Assessment of the Application of Scaling Concepts for Blast Effects Analysis N2 - Blast testing finds its implementation in several applications, e.g. for the purpose of investigation into accidental or intentional explosions, or for an assessment of the level of protection provided by a certain structural configuration. Analytical and/or semi-empirical methods are generally limited to preliminary assessments prior to blast testing. Applications of numerical simulations with hydrocodes coupled with finite element methods (FEM) can only reduce the amount of blast testing required, as these necessitate fulfillment of the fundamental prerequisites of model verification and that of model validation. Field tests are implemented for contact detonations as well as near-field blast scenarios and shock tube tests for far-field blast scenarios. However, these can be extremely resource intensive. Reliable small-scale experiments are a promising alternative. The concepts of dimensional analysis and similarity based on Buckingham’s Π-theorem (1914) have been applied in different fields. For applications to the phenomenon of shock wave propagation, Hopkinson-Cranz or cube-root scaling is a well-established concept. When it comes to scaling the structural response, research has predominantly focused on structures made of metallic materials. Scaled investigations with concrete or reinforced concrete (RC) structures remain limited. The lack of even the most basic guidelines (far from any ‘standardized scaling methods’ for blast tests) show that scaling as a method is not yet established in blast effects analysis. In this preliminary study, we present a systematic approach and evaluation of scaling of blast effects analysis for RC slabs in order to develop guidelines for resource efficient testing methods. We study the blast scenario at two different scales. The focus of these investigations has been on evaluation of scaling of dynamics using pressure sensors, acceleration sensors and fiber optic sensing cables for distributed acoustic sensing (DAS). Further, the resulting plastic behavior upon blast is characterized by distributed strain sensing (DSS) along the same cables. T2 - 27th International Symposium on Military Aspects of Blast and Shock (MABS27) CY - Colmar, France DA - 06.10.2025 KW - Similarity and scaling KW - Blast KW - RC-slabs PY - 2025 SP - 1 EP - 11 AN - OPUS4-64617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Krenek, S. A1 - Eisermann, R. A1 - Failleau, G. A1 - Lu, Xin A1 - Thomas, P. A1 - Kjeldsen, H. A1 - Anhalt, K. T1 - Fibre-optic thermometry to support the clean energy transition N2 - The measurement and control of temperature plays a key role in achieving the European Green Deal targets for a low carbon energy system. Fibre-optic thermometry is an emerging technology that can improve temperature measurement in extreme environments for energy providers and industry due to its distributed sensing and immunity to electromagnetic fields. Various applications for optimisation and monitoring in the energy sector are described, covering the whole range from energy generation to transmission and consumption. However, fibre-optic thermometers have cross sensitivities to other quantities (e.g., strain and humidity) and ageing effects that need to be investigated, quantified and minimised to obtain traceable and reliable measurements. This is particularly important so that applications in critical infrastructure can benefit from future measurements that are not possible with conventional sensors. The European INFOTherm project aims to overcome the limitations that currently prevent the widespread use of fibre-optic thermometry by creating a dedicated European metrology infrastructure for research, development and calibration. First results on measurement uncertainty, improvement of measurement techniques and practical field tests are presented. KW - Industrial processes optimisation KW - Fibre-optic thermometry KW - Distributed temperature sensing KW - Traceability KW - Thermal energy storage KW - Electrical grid resilience PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640075 DO - https://doi.org/10.1515/teme-2025-0044 SN - 2196-7113 VL - 92 IS - 9-10 SP - 392 EP - 405 PB - De Gruyter Brill AN - OPUS4-64007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man T1 - Assessment of prestress loss in a large-scale concrete bridge model under outdoor condition N2 - The presentation shows that subtle variations in coda wave velocity can capture minor temperature effects, offering a good understanding of how a outdoor prestressed concrete structure responds to environmental conditions over time. Ultimately, this work contributes to development of more comprehensive and resilient structural health monitoring strategies for prestressed concrete infrastructure. T2 - EVACES 2025 CY - Porto, Portugal DA - 02.07.2025 KW - Coda wave interferometry KW - Damage detection KW - Prestress loss KW - Seismic interferometry KW - Structural health monitoring PY - 2025 AN - OPUS4-64211 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Biyikal, Mustafa T1 - Development of a Handheld Device for the Trace Detection of Explosives N2 - With the help of the EXIST research transfer the startup True Detection System (TDS) will develop a portable and easy-to-use handheld device based on chemical-optical sensors that can detect the smallest traces of various explosives and markers (e.g. TNT, C4, ANFO, TATP, DMDNB, etc.) and pure salts (e.g. potassium nitrate) reliably and without major cross-sensitivities. The device has been developed over the last 10 years at the Federal Institute for Material Research and Testing (BAM) in cooperation with an SME. Within the next 18 months, a laboratory prototype will now be converted into a commercial device. T2 - Photonics Days Berlin Brandenburg CY - Berlin, Germany DA - 09.10.2023 KW - Explosives KW - Trace detection KW - Handheld device KW - Lab-on-a-chip KW - Start-up PY - 2023 AN - OPUS4-58541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Biyikal, Mustafa T1 - Development of a handheld device for the trace detection of explosives N2 - This presentation introduces a new explosives trace detector (ETD), a handheld device developed by True Detection Systems (TDS). Addressing the limitations of current handheld detectors—such as unreliable measurements and cumbersome operation— the new ETD XT-1 integrates advanced sensor technology, including a Lab-on-a-Chip, to deliver high sensitivity and accuracy. Capable of detecting trace levels of substances like TNT, TATP, and ammonium nitrate, the device offers rapid, user-friendly detection through AI/ML-enhanced algorithms. These algorithms enable precise substance identification by analyzing absorption and desorption rates, significantly reducing false positives. The XT-1 has broad applications in security, hazardous material detection, and environmental monitoring. T2 - Photonics Days Berlin Brandenburg CY - Berlin, Germany DA - 09.10.2024 KW - Explosives KW - Trace detection KW - Handheld device KW - Lab-on-a-chip KW - Fluorescence PY - 2024 AN - OPUS4-61433 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosenbusch, Sjard Mathis T1 - Gradient-enhanced models in blast simulations of concrete structures N2 - Blast experiments on reinforced concrete structures are often limited to small structures and therefore simple shock waves. Such experiments are carried out at the Bundesanstalt für Materialforschung und -prüfung (BAM) and the structural response is investigated using several measuring methods. Complex load scenarios that occur as a result of reflection of the shock wave in larger structures are harder to realize in practice. Numerical simulations for the propagation of the shock wave and the structural response can therefore be an alternative method for the investigation of blast loads on complex structures. For the simulation of concrete under impact and blast loads, several local constitutive models exist that are formulated as plasticity models with softening taken into account by introducing a scalar damage field. Local damage models however often lead to mesh-dependent results which do not converge with mesh refinement. In order to achieve meaningful predictions from numerical experiments, independence from the mesh is needed. In this contribution, the Johnson-Holmquist model (JH2) for brittle damage [2] has been implemented for the free open source software FEniCSx and is investigated in a high strain rate benchmark simulation. Mesh-convergence analyses show that displacements as well as the dissipated plastic energy do not converge with mesh-refinement. Following the gradient-enhancement approach by [1], a gradient-enhanced JH2 model which can be efficiently solved with explicit solvers is introduced and its advantages over the local models are discussed. Since many damage models for concrete share the damage mechanism of the JH2 model, the application of the regularization methods to more complex material models, like the RHT model [3], is also discussed. Advantages of a gradient-enhanced formulation to simulate dynamic strength increase of concrete, as suggested in [1], is discussed as well. T2 - ECCOMAS CONGRESS 2024 CY - Lisbon, Portugal DA - 03.06.2024 KW - Concrete Modeling KW - Explicit Dynamics KW - Gradient-Damage KW - Mesh Convergence PY - 2024 AN - OPUS4-64613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosenbusch, Sjard Mathis T1 - Gradient-Enhanced Plasticity In Explicit Dynamics N2 - The simulation of concrete under impact and blast loads often relies on local constitutive models, typically formulated as plasticity models that incorporate softening through a scalar damage field. However, these local damage models frequently exhibit mesh-dependent results that fail to converge with mesh refinement. In earlier work, the mesh-dependency of a modified Johnson-Holmquist (JH2) model was effectively mitigated through a gradient-enhanced plasticity formulation in explicit dynamics [1]. The gradient-enhancement method for explicit dynamics, originally introduced in [3], involves modifying Peerlings' additional partial differential equation [2] for nonlocal equivalent plastic strain by incorporating inertia. This modification enables the use of explicit solvers, such as the central difference method. Despite these advancements, the model continues to face challenges, particularly slow convergence rates with mesh refinement, which are difficult to analyze due to the JH2 model's complexity. To address these challenges, this study investigates simpler plasticity models, such as von Mises plasticity and Drucker-Prager plasticity, combined with a nonlocal softening term. By systematically incorporating key characteristics of the JH2 model—namely, pressure-dependent yield surfaces, softening, residual yield strength at full damage and a nonlinear volumetric stress responses via an equation of state (EOS)—this work aims to further refine the gradient-enhanced JH2 model and extend these improvements to more complex plasticity models like the RHT model. T2 - GACM 2025 CY - Braunschweig, Germany DA - 21.09.2025 KW - Gradient-enhancement KW - Plasticity KW - Concrete modeling KW - Mesh Convergence PY - 2025 AN - OPUS4-64615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosenbusch, Sjard Mathis T1 - A gradient-enhanced JH2 model for dynamic simulations of concrete structures N2 - Concrete structures subjected to impact and blast loads experience complex failure mechanisms that are challenging to simulate accurately. Local constitutive models formulated using plasticity with softening are commonly used for this purpose. The softening behavior is typically represented by a scalar damage field, which scales the yield surface to capture the degradation of material strength. However, these local models often exhibit meshdependent results with localization of damage into a few cells. To address this limitation, this study combines a modified version of the Johnson-Holmquist (JH2) model with a gradientenhancement approach. The introduction of an inertia term into the additional PDE for the determination of the nonlocal equivalent plastic strain transforms it into a hyperbolic equation, enabling an efficient solution with an explicit dynamics solver. A one-dimensional benchmark simulation demonstrates the differences between the local and gradient-enhanced models. The local model shows severe damage localization and diminishing plastic energy dissipation with finer meshes. In contrast, the gradient-enhanced model distributes damage over multiple elements, though the plastic strain still localizes within a single element. Introducing strain hardening with respect to the local equivalent plastic strain resolves this issue, ensuring convergence of plastic energy and non-localizing plastic strain. These findings are extended and validated with two-dimensional simulations, showcasing the model’s practical relevance. Additionally, the impact of the added inertia term is analyzed in the context of dynamic strength enhancement, a critical characteristic of concrete under high strain rates. The proposed gradient-enhancement approach demonstrates improved numerical stability and mesh-independence compared to local models, making it a suitable tool for simulating concrete behavior under extreme loading conditions. T2 - GAMM 2025 CY - Posen, Poland DA - 07.04.2025 KW - Gradient-enhancement KW - Explicit dynamics KW - High strain rate KW - Concrete modelling PY - 2025 AN - OPUS4-64614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Abschätzung des Anschlagspotentials von Anzündern aus Fahrzeugen N2 - Untersuchung des Auslöseverhaltens von zwei Anzündern aus dem Bereich der Fahrzeugpyrotechnik an sekundären Explosivstoffen im Rahmen der Konformitätsbewertung von Pyrotechnik. T2 - 25. Internationalen Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 01.12.2025 KW - Anzünder KW - Fahrzeugpyrotechnik KW - Sekundäre Explosivstoffe PY - 2025 AN - OPUS4-65008 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klaus, Christian A1 - Soruco Aloisio, Ricardo A1 - Koch, Claudia A1 - Prellwitz, Matthias T1 - Towards Safety and Accuracy of Hydrogen Refuelling Stations through Digital Twins N2 - This paper presents digital quality infrastructure methods for hydrogen refueling stations using the Asset Administration Shell as a standardized digital twin. Implemented at BAM’s test platform, it integrates real-time sensor data, calibration certificates, and compliance documents to support traceable, interoperable asset management. In combination with AI and semantic tools, the system will enable predictive maintenance, remote audits, and improved safety. This approach reduces downtime, enhances transparency, and offers a scalable model demonstrating the potential of digital twins in advancing metrological traceability and operational efficiency in hydrogen technologies. T2 - IMEKO TC-6 International Conference on Metrology and Digital Transformation - M4DConf 2025 CY - Benevento, Italy DA - 03.09.2025 KW - Datenintregration KW - IT KW - Verwaltungsschale KW - Infrastruktur KW - OT KW - Open Source KW - Software PY - 2025 UR - https://www.m4dconf.org/ UR - https://www.sciencedirect.com/journal/measurement-digitalization SP - 1 EP - 6 AN - OPUS4-64951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunert, Wiebke T1 - EU Projekt ODYSSEUS – Home-made explosives and Precursor N2 - Fighting terrorism requires an arsenal of tools. One of these is knowledge about explosive precursors – chemical substances that can be used for legitimate purposes, but can also be misused for the illicit manufacture of home-made explosives. In this context, the EU-funded ODYSSEUS project will develop effective and efficient prognostic, detection and forensic tools to improve prevention, countering and investigation of terrorist incidents involving home-made explosives. The knowledge will help in the development of tools for monitoring the chemical supply chain and sensing in (near) real-time explosive precursors. The tools will be field-tested in three operational use cases. T2 - 46. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 25.04.2026 KW - Home-made explosives KW - Terror attacks KW - Precursor PY - 2025 AN - OPUS4-62999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunert, Wiebke T1 - EU project ODYSSEUS – year 3 Final presentation N2 - Presentation of main results of the R&D project ODYSSEUS regarding home-made explosives. T2 - 24. Internationales Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 25.11.2024 KW - Home-made explosives KW - Precurers KW - Terrorist attacks PY - 2024 AN - OPUS4-61837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit T1 - Skalierung von Sprengversuchen N2 - Eine Machbarkeitsstudie zur ressourceneffizienten sicherheitstechnischen Bewertung. T2 - 25. Internationalen Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 01.12.2025 KW - Sicherheitstechnische Bewertung KW - Sprengversuche KW - Skalierung KW - Numerische Simulationen PY - 2025 AN - OPUS4-65019 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Biyikal, Mustafa T1 - Handgerät für den mobilen Einsatz zur Detektion von Sprengstoffspuren N2 - Mithilfe des EXIST-Forschungstransfers wird ein tragbares und leicht zu bedienendes Handgerät auf der Basis von chemisch-optischen Sensoren entwickelt, welches kleinste Spuren von verschiedensten Sprengstoffen und Markern (z.B. TNT, C4, ANFO, TATP, DMDNB etc.) und reine Salze (z. B. Kaliumnitrat) sicher und ohne größere Querempfindlichkeiten detektieren kann. Das Gerät wurde in den letzten 10 Jahren bei der Bundesanstalt für Materialforschung und -prüfung (BAM) entwickelt und wird von der 2024 ausgegründeten Firma Noxoon GmbH in ein kommerzielles Gerät überführt. Die Vorteile des Handgeräts sind die hohe Selektivität, die hohe Sensitivität, die schnelle Detektion in wenigen Sekunden bis zur Ergebnisanzeige sowie der schnelle und das geringe Gewicht des Gerätes von 900 g. Neben den Vorteilen findet sich auch zahlreiche Alleinstellungsmerkmale in der Benutzung des Gerätes. So können z.B. - reine Salze - Sprengstoffe in Gegenwart von Wasser - Sprengstoffe und Drogen in versiegelten Briefumschlägen detektiert werden. Ein besonderes Alleinstellungsmerkmal ist, dass eine Reinigung des Handgeräts nach Messungen von stark kontaminierten Proben nicht notwendig ist. Für den deutschsprachigen bzw. europäischen Raum existiert noch kein vergleichbares Gerät. Das kommerzielle Gerät soll ab 2025 auf den Markt gebracht werden und wird einen wichtigen Beitrag zur öffentlichen Sicherheit und zum Umweltschutz leisten. T2 - BBK Fachkongress "Forschung für den Bevölkerungsschutz" CY - Bonn, Germany DA - 05.02.2025 KW - Explosivstoffe KW - Detektion KW - Handgerät PY - 2025 AN - OPUS4-65031 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Biyikal, Mustafa T1 - Handgeräte zur Detektion von Sprengstoffspuren N2 - Der Übersichtsvortrag stellt den aktuellen Stand zu Handgeräten zur Detektion von Sprengstoffspuren vor. T2 - Symposium Anlagensicherheit 2025 CY - Hamburg, Germany DA - 04.02.2025 KW - Explosivstoffe KW - Detektion KW - Handgerät PY - 2025 AN - OPUS4-65029 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thöns, Sebastian A1 - Stewart, M. G. T1 - On the cost-efficiency, significance and effectiveness of terrorism risk reduction strategies for buildings N2 - We analyse the performance of risk reduction strategies for Terrorist attacks with Improvised Explosive Devices (IEDs) for large governmental building structures in terms of cost-efficiency, significance and effectiveness Accounting for life safety in conjunction with societal preferences and capabilities. The approach builds upon an extended Bayesian pre-posterior decision analysis and the principles of the marginal lifesaving costs based on the Life Quality Index (LQI). The decision scenario is formulated for a decision maker responsible for the safety of governmental or large commercial buildings and consequently the direct risks, the indirect risks due to fatalities and economical importance of the building beside the expected cost for the individual risk reduction strategies are modelled, aggregated and optimised. The considered risk reduction strategies encompass an explicit consideration and distinction of information and actions such as (i) threat surveillance may trigger the temporary evacuation of the building, (ii) the implementation of protection provisions provided by codes and guidelines, (iii) a detailed progressive collapse assessment and specific protection measures and (iv) the combination of protection and surveillance. All considered strategies are found to contribute to risk reduction and can be costefficient, especially for higher threat probabilities. The risk reduction strategies comply with societal macroeconomic and demographical characteristics and societal preferences according to the LQI. The progressive collapse assessment with targeted protection measures is found to be the most cost-efficient, significant and effective counter-terrorism strategy. This finding points to the necessity for a comprehensive utilisation of scientific methods and sophisticated engineering for progressive collapse assessment to determine targeted protection measures. KW - Significance and effectiveness KW - Risk mitigation strategies KW - Terrorist attacks KW - Value of information KW - Bayesian probability KW - Reliability KW - Risk and decision analysis KW - Decision optimality PY - 2020 DO - https://doi.org/10.1016/j.strusafe.2020.101957 VL - 85 SP - 10195 PB - Elsevier Ltd. AN - OPUS4-50794 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, Davide A1 - Cozzolino, Chiara A1 - Scarponi, Giordano Emrys A1 - Eberwein, Robert A1 - Otremba, Frank A1 - Cozzani, Valerio T1 - Safety Assessment of MLI Super-Insulation Systems for Cryogenic Liquid-Hydrogen Tanks in Fire Scenarios N2 - In the context of green energy transition, cryogenic tanks insulated by MLI and vacuum are emerging as a leading solution to store hydrogen in heavy-duty vehicles. However, the integrity of such tanks can be jeopardized by fire. In such a scenario, MLI materials degradation can occur, leaving the tank unprotected from the fire heat flux, with consequent rapid pressurization and a high risk of failure. This study presents a safety assessment of non-combustible MLI under fire exposure based on the estimation of the time to mechanical failure of the equipment. This is calculated through an innovative model that simulates the thermomechanical response of the tank, including the MLI thermal degradation and the pressure-relief valve (PRV) operation. The application to several case studies that consider a typical LH2 tank featuring a wide range of MLI configurations demonstrated the likelihood of failure in case of exposure to a hydrocarbon pool fire, providing also comprehensive insights into the impact of the insulation characteristics and operating conditions on the time to failure. T2 - Loss Prevention 2025 CY - Bologna, Italien DA - 09.06.2025 KW - LH2 KW - LNG KW - Fire KW - Insulation KW - Safety KW - Tank PY - 2025 DO - https://doi.org/10.3303/CET25116036 SN - 2283-9216 IS - 116 SP - 211 EP - 216 PB - AIDIC AN - OPUS4-63739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Scharff, Erik T1 - Untersuchungen zur Ausbreitung brennbarer Schwergase in längsdurchströmten Straßentunneln N2 - In combination with new types of drive technologies, more and more flammable gases could be introduced into the traffic area “road tunnel” in future. If these vehicles have an accident and the gases are subsequently released, there is the possibility that the mentioned substances show a heavy gas behavior due to their storage conditions. From a safety point of view, this scenario has to be assessed with regard to its effects on the tunnel structure and the people involved. The aim of the experimental investigations carried out in this work is to create the basis for such an analysis by investigating the spreading behavior of the gases after they have been released in the tunnel and determining the influence of individual geometric and operational parameters on this behavior. Specifically, this work is based on the scenario of a continuous, momentum-free release of propane within a vaulted road tunnel with active longitudinal ventilation. The tunnel-specific boundary conditions that are relevant to this scenario are first worked out by a theoretical analysis. The basis of the subsequent experimental part is formed by two test rigs built as part of the work, which are similar in their essential features, but differ in scale. In both facilities, the aforementioned release scenario was simulated under various boundary conditions based on an idealized tunnel segment. The dispersion behavior is primarily assessed by the averaged concentration distribution near the ground, which results from a large number of detectors arranged in the experimental area. The detectors operate on the principle of weakening infrared light in the presence of hydrocarbons. Measurements of the flow field properties accompany the concentration measurements. The conception of the test rig on a scale of 1:12 is based on dimensional analysis. The actual release campaign comprises a large number of individual experiments in which selected parameters were varied over the tunnel-relevant range. The predicted heavy gas behavior for propane emerged clearly in the experiments. In cases in which the cloud laterally reaches the tunnel walls, the gases are channeled, which is accompanied by reduced longitudinal dilution. It was possible to identify the release rate and the flow velocity as the factors that have the greatest influence. The former basically increased the concentration, while the latter decreased it. All other tested parameters resulted in more complex propagation situations, which force a differentiated consideration of the influence. Lifting the source from the ground also reduced the concentration. In the case of an eccentrically arranged source and a transverse slope of the roadway, the influence is largely limited to the lateral concentration distribution in the immediate vicinity of the source. Nevertheless, both parameters plus a possible longitudinal slope of the roadway only showed a slight effect on the area far-downstream from the source. In addition, the phenomenon of backlayering, which is known from the spreading of fire smoke in the tunnel, could be demonstrated with a steep longitudinal slope. Obstacles increased the complexity of the situation. While globally the dilution of the cloud is partly invariant to obstacles, locally an increase as well as a decrease in concentration can be observed under certain conditions. For the unobstructed tunnel, it was finally possible to define a dimensionless parameter that describes the curve of the longitudinal dilution on the ground within the heavy gas cloud. From this, a simple graphical nomogram is derived for the continuous release of heavy gases in an unobstructed tunnel environment, which can be used to estimate the concentration in relation of a dimensionless source distance. For exploring the real, undistorted behavior experiments were also carried out in original scale. Due to the similarity of both test rigs in terms of scale, the test results can also be used to check the scalability of the spreading situations. For that, two configurations that have already been examined in small scale were selected. The main limitation for test execution and regarding the scalability comparison was the dependence of the flow conditions within the test rig from external wind conditions which occurred despite of taken countermeasures. The large-scale release was associated with pronounced fog formation. The near-ground spreading corresponding to the heavy gas behavior could be confirmed. However, in detail the spread was far more unsteady. Looking at the time-averaged concentrations, the processes already known from the small-scale test were qualitatively well approximated. Remaining quantitative differences, however, require critical consideration. This discrepancy is more likely a consequence of the experimental compromises have to be made in the specific case. From the observed gas behavior, the development of a surface fire initiated by ignition of the re-leased gases is considered to be the most likely subsequent scenario for the release of heavy, flam-mable gases in tunnel-like enclosures. The thesis concludes with recommendations on the methodological approach to be favored in the future. KW - LNG KW - Schwergas KW - Stoffausbreitung KW - Propan PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:gbv:ma9:1-1981185920-1206411 DO - https://doi.org/10.25673/118683 VL - 2025 SP - 1 EP - 225 PB - Otto-von-Guericke-Universität Magdeburg, Fakultät für Verfahrens- und Systemtechnik CY - Magdeburg AN - OPUS4-65012 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hajhariri, Aliasghar T1 - Experimental and Numerical Investigation on Multi-layer Insulation Thermal Deterioration N2 - To reduce carbon dioxide emissions, energy carries such as hydrogen consider to be a solution. Consumption of hydrogen as a fuel meets several restrictions such as its low volumetric energy density in gas phase. To tackle this problem, storage as well as transportation in liquid phase is recommended. To be able to handle this component in liquid phase, an efficient thermal insulation e.g., MLI insulation is required. Some studies have been revealed vulnerability of this type of insulation against high heat flux, for instance a fire accident. Some investigations have been depicted the importance of consideration of the MLI thermal degradation in terms of its reflective layer. However, limited number of studies have been focused on the thermal degradation of spacer material and its effect on the overall heat flux. In this study, through systematic experimental measurements, the effect of thermal loads on glass fleece, glass paper as well as polyester spacers are investigated. The results are reported in various temperature and heat flux profiles. Interpreting the temperature profiles revealed as the number of spacers in the medium increases, the peak temperature detectable by the temperature sensor on the measurement plate decreases. Moreover, the contribution of each individual spacer in all cases regarding the experimental temperature range is assessed to be around 8%. This value may increase to around 50% for glass paper and polyester spacers, and to around 25% for glass fleece spacers as the number of spacer layers increases up to six layers. To utilize the outcomes of the experiment later and integrate the results into numerical and CFD simulations, a model is proposed for the mentioned experimental temperature range up to 300°C to predict a heat flux attenuation factor. The model proposes a fitting factor that can reproduce the least square fitted line to the experimental data. T2 - 15th International Symposium on Hazards, Prevention, and Mitigation of Industrial Explosions Naples (ISHPMIE) CY - Naples, Italy DA - 10.06.2024 KW - Multi-Layer Insulation KW - Cryogenic KW - Liquid Hydrogen KW - Heat Transfer KW - Hydrogen Storage PY - 2024 AN - OPUS4-60457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Davide, Camplese A1 - Giordano, Emrys Scarponi A1 - Valerio, Cozzani A1 - Frank, Otremba T1 - Experimental investigation on the behavior of thermal super insulation materials for cryogenic storage tanks in fire incidents N2 - The number of vehicles using or transporting cryogenic fuels such as Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) increases fast in the land transportation sector. Does this also entail new risks? The storage of cryogenic fuels requires tanks with Thermal Super Insulations (TSI) to keep the fluid cold and limit the formation of boil-off gas. TSI has proven itself in some applications since the middle of the 20th century, but in the land transport sector they are still quite new, where accidents involving fires, collisions, and their combination are to be expected. This work focuses on investigating the behavior of different types of TSI while exposed to a heat source representing a fire. To this aim, a High-Temperature Thermal Vacuum Chamber (HTTVC) was applied, which allows the thermal loading of a thermal insulation material in a vacuum and measuring the heat flow transported through the TSI in parallel. In this study, the results of 6 samples are presented regarding 3 types of MLI, rock wool, perlites, and microspheres. The thermal exposure caused different effects on the samples. In practice, this can be connected to the rapid release of flammable gases as well as to a Boiling Liquid Expanding Vapour Explosion (BLEVE). These results are relevant for reducing the risks to people and infrastructures in the progressive establishment of tanks for cryogenic fluids in our industry and society. The data presented in the study can be used to improve the design of tanks and TSIs, the assessment of accident scenarios, and the development of measures for first responders. KW - Liquefied hydrogen KW - Liquefied natural gas KW - Tanks KW - Fire KW - Insulation KW - MLI KW - Perlite KW - Rock wool KW - Microspheres PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-599947 DO - https://doi.org/10.1016/j.psep.2024.04.131 SN - 0957-5820 VL - 187 SP - 240 EP - 248 PB - Elsevier AN - OPUS4-59994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Cryogenic Storage Tanks In Fire Incidents N2 - The ongoing geo-political conflicts and the increasing need for the implementation of measures to improve the energetic system sustainability are increasing the importance of tanks for storing cryogenic fluids in the energy industry. The most common example of cryogenic tank applications is the transport of natural gas and hydrogen in their liquid form (LNG and LH2 respectively) for which, considering the same transport volume cryogenic storage ensures significantly higher transport capacities with respect storage based solely on overpressure. A common feature of all cryogenic transported fluids is that their condition must be maintained minimizing heat leaks from the environment as much as possible. This is achieved by the implementation of thermal super Insulations (TSI) systems based on e. g. rock wool, perlites, microspheres, multilayer insulations (MLI), and vacuum which have proven to be effective in applications. However, due to the relatively short period of use in some applications, the small number of documented incidents, and the still few investigations carried out in the field, the exploitation of such systems in the cryogenic fluids transport sector still suffers from insufficient knowledge about the course and consequences of incidents. Accidents involving collisions, fires, and their combination are quite common in the transportation sector and may generate extraordinary loads on the tank and its insulation system, eventually leading to tank failure. The present study focuses on the behavior of TSI systems in tanks when it is exposed to an external heat source representative of a hydrocarbon fire scenario. This may cause an increase of the heat flux into a tank by several orders of magnitude with respect to normal design conditions, thus inducing severe and in the TSI, causing the rapid release of flammable gas and even resulting in a Boiling Liquide Expanding Vapour Explosion (BLEVE). To study such scenarios a test rig was developed at BAM that allows testing of TSI at industrial conditions and enables subsequent analysis of TSI samples. This test rig considers the typical double-walled design of tanks for cryogenic fluids with vacuum and an additional insulating material in the interspace. Adjustable electrical heating elements simulate the fire on one side of the double wall. This process allows the implementation of repeatable heat loads of up to 100 kW/m². The other side of the double wall is represented by a fluid-supported heat exchanger, which allows the simulation of cold or cryogenic conditions in the test rig, and to determine the heat flux transmitted through the double wall. Thus, the test rig allows thermal loading and performance analysis of TSI samples at the same time. In the presentation, the results of diverse tested TSI systems will be presented and discussed. As a result of this study, the list of advantages and disadvantages for the choice of tested TSI expands. Within the test, all samples degraded as a consequence of a hydrocarbon fire-orientated thermal load. Strong differences in the behavior of the tested TSI systems over temperature, location, and time were observed. Additionally, the tested MLI insulations were significantly more resistant to their base materials. These results are relevant for the design, the definition of national and international regulations, the Risk assessment, and the development of safety concepts for cryogenic tanks. T2 - Cryogenic Storage Tanks CY - Munich, Germany DA - 18.04.2024 KW - LH2 KW - LNG KW - Fire KW - Insulation PY - 2024 AN - OPUS4-59921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Storages For Cryogenic Gases And Their Safety Part 2 N2 - To accelerate the hydrogen uptake in Europe the project KICstartH2 funded by the European Union arranged the Joint European Summer School (JESS) that deals with several topics around hydrogen. A topic in this framework is the transport and storage of energy by hydrogen. Here cryogenic energy carriers are seen as having great potential. This is because they allow significantly higher volumetric energy densities to be achieved than when these energy carriers are stored at typical temperatures on Earth. This is important for numerous energy-intensive applications, such as those found in all transport sectors. Important cryogenic energy carriers include liquefied hydrogen (LH2) and liquefied natural gas (LNG). This presentation deals with the consequences of an accidental release of a cryogenic liquid and the consequences of a fire affecting a tank. T2 - Joint European Summer School (JESS) CY - Athens, Greece DA - 15.09.2024 KW - Liquefied hydrogen KW - Liquefied natural gas KW - Cryogenic storage tank KW - Fire KW - Safety KW - Consequences PY - 2024 AN - OPUS4-61084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Camplese, D. A1 - Scarponi, G. E. A1 - Cozzani, V. A1 - Otremba, Frank T1 - Insulation Materials Used in Tanks for the Storage of Cryogenic Fluids in Fire Scenarios N2 - The importance of tanks for storing cryogenic fluids in the energy industry is increasing because of ongoing political conflicts and the implementation of more environmentally friendly energy sources. Key representatives for the application of cryogenic tanks are natural gas in the form of Liquefied Natural Gas (LNG) and hydrogen, e. g. in the form of Liquefied Hydrogen (LH2), for which significantly higher transport capacities can be achieved with the same transport volume using cryogenic storages than with storages based solely on overpressure. What applies to all cryogenic transported fluids in common is their condition that must be maintained. Hence heat flows into the preserved fluid must be minimized. Thermal super Insulations (TSI) based on e. g. multilayer insulations (MLI), perlites, and vacuum are utilized for this purpose and have already proven themselves in similar applications. However, for the use of tanks for cryogenic fluids in the transport sector, there is insufficient knowledge regarding the course and consequences of incidents, which is due to the still short period of use and the few documented incidents, hence few investigations carried out in this field. Typical scenarios in the transport sector represent car accidents with collisions, fires, and their combination, which are associated with extraordinary loads on the tank. The focus of this study is to investigate the behavior of TSI as a result of their thermal exposure to a heat source representing a fire. It is worth mentioning that this could lead to an increase of the heat flux into a tank by several orders of magnitude, and to permanent damage of the TSI, ultimately rapid release of flammable gas as well as a Boiling Liquide Expanding Vapour Explosion (BLEVE). For this purpose, a high temperature thermal vacuum chamber (HTTVC) has been developed that allows thermal loading of MLI or perlites in a vacuum and simultaneous measurement of heat flow through this TSI. The HTTVC is designed to represent realistic insulation conditions and to withstand thermal loads from typical design fires. The HTTVC was applied to investigate TSI based on MLI and vacuum. It is shown that the thermal stress caused permanent damage to the TSI, with shrinkage, phase change, pyrolysis, and condensation being significant damage mechanisms. The results are relevant for the evaluation of accident scenarios and can thus contribute to the improvement of TSI and the development of emergency measures for the protection of persons and infrastructures. T2 - ASME 2023 Pressure Vessels & Piping Conference (PVP2023) CY - Atlanta, Georgia, USA DA - 16.07.2023 KW - LH2 KW - LNG KW - Fire KW - MLI KW - Safety PY - 2023 AN - OPUS4-57974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scarponi, G. T1 - Modelling the response of LH2 tanks equipment with Multi Layer Insulation to fire exposure N2 - Hydrogen is among the most promising candidates to replace fossil fuels in the energy transition. Hydrogen-powered vehicles are already a reality, and their number is foreseen to increase considerably in the next decade. Among the possible solutions to store hydrogen in such vehicles, cryogenic tanks equipped with multi-layer insulation (MLI) appear to be one of the most effective to ensure high volumetric energy density. A potential loss of integrity of this kind of storage equipment might lead to severe consequences due to high flammability of hydrogen. This might occur, for instance, as a consequence of the exposure to an external source of heat such as a fire following a car accident. Real scale fire test results suggest that the super insulating performance of MLI systems may undergo severe degradation when this is subjected to high temperature, leaving the tank almost unprotected and leading to failure in a relatively short time. Characterizing this kind of accident scenario is crucial to ensure a safe design of storage tanks for Hydrogen-powered vehicles. This presentation provides an overview of the ongoing research work on modelling MLI LH2 tanks exposed to fire. Lumped and computational fluid dynamic based models are presented, highlighting current gaps. The relevance of taking MLI degradation into account when simulating the pressure increase due to external fire exposure is here demonstrated through the analysis case studies. T2 - H2-Kolloquium CY - Online meeting DA - 21.06.2023 KW - LH2 KW - Cold KW - MLI PY - 2023 AN - OPUS4-57878 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Heßmann, Jennifer A1 - Werner, Jan A1 - Scarponi, Giordano Emrys A1 - Cozzani, Valerio A1 - Otremba, Frank T1 - Investigation of realistic fire scenarios involving cryogenic storage tanks N2 - The number of vehicles using or transporting cryogenic fuels such as Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) increases fast in the land transportation sector. Does this also entail new risks for instance from a BLEVE? A key to answer this question is to research representative fires by its characterization and its effect on the insulation. At BAM’s technical test side in Germany, a test series was started to answer this question among others. This paper presents results on a pool fire under a colorimeter, that simulates a tank. The investigation points out, that the full fire characterization approach allows to represent the fire. The findings are relevant for the investigation of a representative design fire that is applicable for the approval and improvement of tanks as well as to research accident scenarios and their consequences. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - LH2 KW - Insulation KW - Fire KW - Liquefied Natural Gas KW - Safety PY - 2025 AN - OPUS4-63425 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Experimental Research Of A Tank For A Cryogenic Fluid With a Wall Rupture In a Fire Scenario N2 - In the course of decarbonizing the energy industry, cryogenic energy carriers as liquefied hydrogen (LH2) and liquefied natural gas (LNG) are seen as having great potential. In technical applications, the challenge is to keep these energy carriers cold for a long time. This is achieved in the road transport sector and also stationary applications by thermal super insulations (TSI) which based on double-walled tanks with vacuum and multilayer insulation (MLI) in the interspace. This study focuses on the behaviour of widely used combustible MLI in a fire scenario, at vacuum and atmospheric pressure conditions. The former corresponds to the typical design condition and the latter to the condition after an outer hull rapture of a tank. Furthermore, two fire scenarios were taken into account: a standard-oriented approach and a hydrocarbon fire-oriented approach. For the study, a test rig was applied that allows testing of TSI at industrial conditions and subsequent analysis of TSI samples. The test rig allows thermal loading and performance analysis of TSI samples at the same time. Comparing the tests, the samples degraded differently. However, no sudden failure of the entire MLI was observed in any test. These results are relevant for the evaluation of incidents with tanks for the storage of cryogenic fluids and can thus contribute to the improvement of TSI and the development of emergency measures for the protection of persons and infrastructures. T2 - 15th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Neapel, Italy DA - 10.06.2024 KW - Liquefied hydrogen KW - Liquefied natural gas KW - Cryogenic storage tank KW - Fire KW - Thermal insulation KW - Multi-Layer Insulation PY - 2024 AN - OPUS4-60456 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - Systems with Cryogenic Liquefied Gases in Fire Incidents N2 - Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. The focus of this study is to investigate the behavior of different types of TSI when exposed to a heat source that represents a fire. Therefore, a High- Temperature Thermal Vacuum Chamber (HTTVC) was used that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this study, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. The thermal exposure caused different effects on the samples. In practice, this can be connected to the rapid release of flammable gases as well as a Boiling Liquid Expanding Vapour Explosion (BLEVE). These results are relevant for the evaluation of accident scenarios, the improvement of TSI, and the development of emergency measures. T2 - IMECE 2023 CY - New Orleans, Louisiana, USA DA - 29.10.2023 KW - LH2 KW - LNG KW - Fire PY - 2023 AN - OPUS4-58769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lohrer, Christian A1 - Grunert, Wiebke A1 - Walter, Astrid T1 - Homemade explosives & precursor – ODYSSEUS sagt dem Terrorismus den Kampf an N2 - Dieser Beitrag beschreibt das EU-finanzierte Forschungsprojekt ODYSSEUS (preventing, countering, and investigating terrorist attacks through prognostic, detection, and forensic mechanisms for explosive precursors) und die Aufgaben der BAM in diesem Zusammenhang. KW - Explosionsgefährliche Eigenschaften KW - Homemade explosives PY - 2025 SN - 0941-4584 VL - 2025 IS - 47 SP - 10 EP - 12 AN - OPUS4-65229 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Forschung zum Thema Feuer an der BAM N2 - Feuer und deren Auswirkung stellen ein Querschnittsthema über die Aktivitätsfelder der BAM dar. Schwerpunkte stellen dabei Brände in Gebäuden, Industrieanlagen und Lagerräumen, der Vegetation, an Fahrzeugen und Tanks sowie Brände im Zusammenhang mit neuen Energieträgern dar. Im Vortrag werden die einzelnen Themen und exemplarische für deren Erforschung nutzbare Infrastruktur vorgestellt. T2 - Transfer on Fire 2 CY - Luckenwalde, Germany DA - 10.07.2025 KW - Feuer KW - Brandlasten PY - 2025 AN - OPUS4-63686 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schiaroli, Alice A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Eberwein, Robert A1 - Ustolin, Federico A1 - Cozzani, Valerio T1 - Modelling the behaviour of cryogenic liquid hydrogen tanks engulfed in fire N2 - The safe use of liquid hydrogen as a clean fuel requires a deep understanding of its behaviour in accident scenarios. Among other scenarios, the possible involvement of cryogenic liquid hydrogen tanks in engulfing fires is of particular concern, due to the potentially severe consequences. This study proposes a computational fluid dynamic model suitable to simulate the behaviour of liquid hydrogen tanks equipped with multi-layer insulation (MLI) engulfed in fire. An original approach has been developed to assess the progressive degradation of the performance of the thermal insulation, that is crucial in determining the tank pressurization and failure. The model is validated against full-scale experimental fire tests. The outcomes of the model reproduce the progressive pressurization and the opening time of the pressure relief valve within 2 % error. The results demonstrate the importance of accounting for the dynamic evolution of the progressive degradation of the insulation when evaluating tank pressurization, and they highlight the limitations of empirical, simplified state-of-the-art approaches. Furthermore, the analysis evidences the key role of the fire temperature in governing tank response, stressing the need for proper fire characterization to support reliable modelling of fire scenarios and the development of emergency planning and mitigation strategies ensuring the structural integrity of liquid hydrogen tanks during fire attacks. KW - LH2 KW - LNG KW - Fire KW - Tank PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652920 DO - https://doi.org/10.1016/j.psep.2025.108319 SN - 0957-5820 VL - 206 SP - 1 EP - 14 PB - Elsevier Ltd. AN - OPUS4-65292 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Agasty, Amit A1 - Costard, Rene A1 - Kadoke, Daniel A1 - Kind, Thomas A1 - Hicke, Konstantin A1 - Hüsken, Götz T1 - A comprehensive experimental assessment of reinforced concrete walls under blast: In situ monitoring of loading, dynamic response and damage with NDT methods and embedded sensors N2 - A safety or security related assessment of explosions, accidental and intentional scenarios alike, often necessitate performance of resource intensive replication tests. For an efficient assessment without performing full scale blast tests, e.g., supported by numerical simulations, detailed knowledge is necessary to predict the blast loading from a given charge configuration, the resulting dynamic response of the structure under investigation as well as the resulting damage. Validation of numerical simulation requires the spatially resolved acquisition of all these parameters in real time. In this paper we present a set of measurement techniques and discuss their suitability for monitoring reinforced concrete (RC) walls under blast loading. Different blast-loading scenarios were realized by varying the charge weight and the standoff distance. The dynamic loading of the wall was characterized with pressure sensors complemented by numerical simulations using the APOLLO Blastsimulator and ConWep. High speed digital image correlation (DIC) was implemented in combination with multiple acceleration sensors to observe the dynamic deflection of the walls during the loading and to determine the residual deformation after the loading had ceased. In addition, one test specimen was instrumented with fiber optic sensor cables. These fiber optic sensors were used for distributed acoustic sensing (DAS) delivering information on dynamics of compression and tension cycles from within the structure. Additionally, the local damage pattern emerging during the series of blasts was determined via distributed fiber optic strain sensing (DSS) to enable the characterization of visual and non-visual damage to the structure. The obtained information was compared to results by an ultrasound structure-scanner. KW - Blast testing KW - Reinforced concrete KW - NDT methods KW - Fiber optic sensing KW - DIC KW - Numerical simulations KW - APOLLO Blastsimulator PY - 2025 DO - https://doi.org/10.1177/20414196251353795 SN - 2041-4196 SP - 1 EP - 31 PB - Sage Publications AN - OPUS4-63832 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Bernauer, F. A1 - Niederleithinger, Ernst A1 - Igel, H. A1 - Hadziioannou, C. T1 - Assessment of prestress loss in a large-scale concrete bridge model under outdoor condition N2 - Environmental conditions affect the accuracy of field measurements used to monitor civil structures. Previous studies have shown that measured dynamic responses often lack the sensitivity needed for effective localized damage detection. To address this issue, our study focuses on distinguishing environmental effects from damage related effects in measured data to enhance vibration-based damage identification methods. Experimentally, the problem of prestress loss in a prestressed concrete bridge model was examined. By adjusting the pre-stressing force in a large-scale concrete bridge model, cracking phenomena were observed. To demonstrate field monitoring of a large-scale prestressed structure, noise recording was performed and the measurement data was analyzed with operational modal analysis. Additionally, ultrasonic testing, known for its high sensitivity in damage localization, was used to cross-check the structural damage. Seismic and coda wave interferometry were also employed to estimate wave velocities, providing insights into the level of prestress loss and temperature sensitivity. Ultimately, these measurable wave properties help to overcome the uncertainties associated with traditional vibration-based damage detection methods. T2 - EVACES 2025 CY - Porto, Portugal DA - 02.07.2025 KW - Prestress Loss KW - NDT KW - Ambient Vibration KW - Ultrasonic Testing KW - Coda Wave Interferometry KW - Seismic Interferometry PY - 2025 SN - 978-3-031-96105-2 DO - https://doi.org/10.1007/978-3-031-96106-9_20 VL - 675 SP - 181 EP - 189 PB - Springer Nature CY - Cham AN - OPUS4-64212 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Tiebe, Carlo A1 - Bayat, Mehmet E. A1 - Bartholmai, Matthias T1 - Unsicherheit bei der Probenahme von Sprengstoffspuren und Detektion durch Ionenmobilitätsspektrometrie N2 - IMS trägt zur Luftfrachtsicherheit bei Geltende Luftsicherheitsgesetze verpflichten Luftsicherheitsbehörden, Flughafenbetreiber und Fluggesellschaften umfassende Sicherheitsmaßnahmen auf den Flughäfen zu ergreifen, um die Gefahr möglicher terroristischer Bedrohungen zu erkennen und zu verhindern. Wenn ein verdächtiges Objekt durch Röntgenstrahlen identifiziert wurde, kann die IMS als schnelles Analyseverfahren vor Ort orthogonal zur Radiologie eingesetzt werden, um chemische Informationen über Gefahrstoffe wie Sprengstoffe oder Drogen vor dem Abflug zu erhalten. Vor der Detektion von Sprengstoffen beginnt die Untersuchung eines verdächtigen Objekts mit der Probenahme mittels Wischprobensammlern. Eine Luftsicherheitskontrollkraft wischt dabei Oberflächen des Objekts mit einem Probensammler ab, um Partikel von Gefahrstoffen zu sammeln. Der beladene Probensammler wird anschließend in einen Probeneinlass eingeführt. Nach thermischer Desorption der gesammelten Stoffe erhält der Bediener (z. B. Luftsicherheitskontrollkraft) ein boolesches Ergebnis - "Alarm" oder "Kein Alarm". Verfahren und Ergebnisse In dieser Studie wurden drei Verfahren mit vier ECAC-zertifizierten ETD-Geräten zur Entwicklung eines Unsicherheitskonzeptes bezüglich der Probenahme (PN) angewandt: I) direkte Probenaufnahme durch lösemittelbasierten Auftrag einer bekannten Sprengstoffmenge auf einem Probensammler, II) Auftragung einer bekannten Menge eines gelösten Sprengstoffs auf einem 10 cm × 10 cm Substrat (Aluminium, Papier, Eisen und Polyvinylchlorid) und manuelle PN nach Lösemittelverdampfung, III) lösemittelbasierter Sprengstoffauftrag auf eine PTFE- oder PTFE-beschichtete Glasfaseroberfläche, nach Lösemittelverdunstung trockene Übertragung auf das zu beprobende Substrat zur PN. Nach dem binären Regressionsverfahren wurde die funktionale Abhängigkeit der Detektionswahrscheinlichkeit von einer bekannten Sprengstoffmasse mit einer Logit-Funktion beschrieben: POD=1/(1+e^(-A·(m-B))). Dabei ist POD die Wahrscheinlichkeit der Detektion für eine bekannte Sprengstoff-Masse, die Parameter A (logistische Wachstumsrate der Kurve) und B (m-Wert des Mittelpunktes des Sigmoids) sind geschätzte Parameter nach der Methode der kleinsten Quadrate, und m ist die Sprengstoffmasse. Das entwickelte Messunsicherheitsmodell kombiniert quantitative Ergebnisse aus Wägen, Lösen und Pipettieren sowie qualitative Ergebnisse - "Alarm" oder "Kein Alarm" und die Unsicherheit der PN. Identifizierte Unsicherheitsursachen sind die Durchführung der Wischprobenahme, Staub, Lösemitteleffekte und die Unsicherheit bei der Herstellung von Testlösungen. T2 - 8. IMS-Anwendertreffen CY - Potsdam, Germany DA - Veranstaltung wurde abgesagt - Meeting was cancelled KW - IMS KW - Ionenmobilitätsspektrometrie KW - Wischprobenahme KW - binäres Regressionsverfahren KW - ETD KW - Sprengstoffspurendetektion PY - 2020 VL - 2020 SP - 9 EP - 9 PB - Universität Potsdam CY - Potsdam AN - OPUS4-51136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Safety assessment of MLI super-insulation systems for cryogenic liquid-hydrogen tanks in fire scenarios N2 - In the context of green energy transition, cryogenic tanks featuring MLI systems are emerging as a leading solution to store hydrogen in heavy-duty vehicles. However, the integrity of such tanks can be jeopardized by fire. In such a scenario, MLI materials degradation can occur, leaving the tank unprotected from the fire heat flux, with consequent rapid pressurization and a high risk of failure. This study presents an assessment of aluminum-based MLI for liquid hydrogen cryogenic tanks under fire exposure based on the estimation of the time to mechanical failure of the equipment. This is calculated through an innovative model that simulates the thermomechanical response of the tank, including the MLI thermal degradation and the pressure-relief valve (PRV) operation. The application to several case studies that consider a typical LH2 tank featuring a wide range of MLI configurations demonstrated the likelihood of failure in case of exposure to a hydrocarbon pool fire, providing also comprehensive insights into the impact of the insulation characteristics and operating conditions on the time to failure. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - LH2 KW - Insulation KW - Tanks KW - Fire KW - LNG PY - 2025 AN - OPUS4-63427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Otremba, Frank A1 - Cozzani, Valerio T1 - Modelling Fire Response of Cryogenic Liquid Hydrogen Tanks Equipped with Multilayer Insulation (MLI) Systems N2 - In the context of the growing global interest in hydrogen-based green energy, cryogenic tanks equipped with multi-layer insulation (MLI) are emerging as a leading solution for storing hydrogen in vehicles. The integrity of these systems might be threatened during fire exposure. This can trigger the degradation of the MLI materials and induce rapid pressurization of the tank with a high risk of catastrophic failure. In this work, a novel lumped model to simulate the thermal response of MLI-equipped cryogenic liquid hydrogen tanks is presented. The model integrates the accurate database “Coolprop” for hydrogen thermodynamic properties and sub-models for detailed simulation of MLI degradation, providing a realistic simulation of the experimental data obtained under normal operating conditions. The application of the model to several case studies considering different numbers of MLI layers and tank geometries demonstrates that aluminum-based MLI offers scarce protection in case of exposure to a hydrocarbon poolfire. T2 - CISAP 11 CY - Neapel, Italy DA - 15.09.2024 KW - LH2 KW - LNG KW - Cryogenic storage tank KW - Insulation KW - MLI PY - 2024 DO - https://doi.org/10.3303/CET24111076 SN - 2283-9216 VL - 111 SP - 451 EP - 456 PB - AIDIC The Italian Association of Chemical Engineering AN - OPUS4-61384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Cozzani, Valerio A1 - Otremba, Frank ED - Di Benedetto, Almerinda T1 - Experimental Research Of A Tank For A Cryogenic Fluid With A Wall Rupture In A Fire Scenario N2 - In the course of decarbonizing the energy industry, cryogenic energy carriers as liquefied hydrogen (LH2) and liquefied natural gas (LNG) are seen as having great potential. In technical applications, the challenge is to keep these energy carriers cold for a long time. This is achieved in the road transport sector and also stationary applications by thermal super insulations (TSI) which based on double-walled tanks with vacuum and multilayer insulation (MLI) in the interspace. This study focuses on the behaviour of widely used combustible MLI in a fire scenario, at vacuum and atmospheric pressure conditions. The former corresponds to the typical design condition and the latter to the condition after an outer hull rapture of a tank. Furthermore, two fire scenarios were taken into account: a standard-oriented approach and a hydrocarbon fire-oriented approach. For the study, a test rig was applied that allows testing of TSI at industrial conditions and subsequent analysis of TSI samples. The test rig allows thermal loading and performance analysis of TSI samples at the same time. Comparing the tests, the samples degraded differently. However, no sudden failure of the entire MLI was observed in any test. These results are relevant for the evaluation of incidents with tanks for the storage of cryogenic fluids and can thus contribute to the improvement of TSI and the development of emergency measures for the protection of persons and infrastructures. T2 - 15th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions (ISHPMIE) CY - Neapel, Italy DA - 10.06.2024 KW - Liquefied hydrogen KW - Liquefied natural gas KW - Cryogenic storage tank KW - Fire KW - Thermal insulation KW - Multi-Layer Insulation PY - 2024 SP - 707 EP - 717 AN - OPUS4-60460 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Cozzani, Valerio A1 - Otremba, Frank T1 - A comparative study on insulation materials in tanks for the storage of cryogenic fluids in fire incidents N2 - Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. The focus of this study is to investigate the behavior of different types of TSI when exposed to a heat source that represents a fire. Therefore, a High-Temperature Thermal Vacuum Chamber (HTTVC) was used that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this study, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. The thermal exposure caused different effects on the samples. In practice, this can be connected to the rapid release of flammable gases as well as a Boiling Liquid Expanding Vapour Explosion (BLEVE). These results are relevant for the evaluation of accident scenarios, the improvement of TSI, and the development of emergency measures. T2 - IMECE 2023 CY - New Orleans, Louisiana, USA DA - 29.10.2023 KW - LH2 KW - LNG KW - Fire PY - 2023 SP - 1 EP - 7 AN - OPUS4-58768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Scarponi, Giordano T1 - Performance of MLI systems for LH2 Tanks in fire scenarios N2 - In the course of decarbonizing the energy industry, cryogenic energy carriers are seen as having great potential. This is because they allow significantly higher volumetric energy densities to be achieved than when these energy carriers are stored at typical temperatures on Earth. This is important for numerous energy-intensive applications, such as those found in all transport sectors. Important cryogenic energy carriers include liquefied hydrogen (LH2) and liquefied natural gas (LNG). The challenge is to keep the energy carrier cold for a long time. This is achieved by the implementation of thermal super-insulations (TSI) systems based on multilayer insulations (MLI), microspheres, perlites, and vacuum for instance, and which have proven to be effective in several cryogenic applications. However, due to the short period of use, the low number of documented incidents, and the still few investigations carried out in the field, the exploitation of such systems in the transport sector still suffers from insufficient knowledge about the course and consequences of incidents. Accidents involving collisions, fires, and their combination are quite common in the transportation sector and may generate extraordinary loads on the tank and its insulation system, eventually leading to tank failure. The presentation summarizes the findings from the cooperation of the University of Bologna and BAM regarding the experiments on diverse types of super-insulations with the High Temperature Thermal Vacuum Chamber, as well as the model approaches that were developed to calculate the heat transfer and degradation of MLI’s during high thermal exposure. As an outlook the application of the models, the Cryogenic High Temperature Thermal Vacuum Chamber, and the fire test on HGV-components are presented. T2 - ELVHyS - International Stakeholder's Seminars CY - Bologna, Italy DA - 30.09.2024 KW - LH2 KW - LNG KW - Cryogenic storage tank KW - Fire KW - Safety PY - 2024 AN - OPUS4-61205 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Modelling Fire Response of Cryogenic Liquid Hydrogen Tanks Equipped with Multilayer Insulation (MLI) Systems N2 - In the context of the growing global interest in hydrogen-based green energy, cryogenic tanks equipped with multi-layer insulation (MLI) are emerging as a leading solution for storing hydrogen in vehicles. The integrity of these systems might be threatened during fire exposure. This can trigger the degradation of the MLI materials and induce rapid pressurization of the tank with a high risk of catastrophic failure. In this work, a novel lumped model to simulate the thermal response of MLI-equipped cryogenic liquid hydrogen tanks is presented. The model integrates the accurate database “Coolprop” for hydrogen thermodynamic properties and sub-models for detailed simulation of MLI degradation, providing a realistic simulation of the experimental data obtained under normal operating conditions. The application of the model to several case studies considering different numbers of MLI layers and tank geometries demonstrates that aluminum-based MLI offers scarce protection in case of exposure to a hydrocarbon poolfire. T2 - CISAP 11 CY - Neapel, Italy DA - 15.09.2024 KW - Liquefied hydrogen KW - LNG KW - Fire KW - Insulation KW - MLI PY - 2024 AN - OPUS4-61389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hajhariri, Aliasghar T1 - Investigation of Super Insulation degradation of a tank for cryogenic goods. Effect of fire on the storage of Cryogenic fluids N2 - Cryogenic liquefied gases, such as liquid hydrogen (LH2) and liquefied natural gas (LNG), are becoming more popular as eco-friendly energy sources. However, using these gases more often increases the risk of accidents, making it important to conduct thorough risk assessments. The storage systems for these gases rely on thermal superinsulation (TSI), which can fail under extreme heat, especially during fires. Therefore, it is essential to study how and why TSI fails. This research (part of PhD topic) aims to examine insulation performance, thereby improving the overall safety of cryogenic storage systems. T2 - Colloquium of Departement 3 CY - Berlin, Germany DA - 27.05.2024 KW - Investigation KW - Insulation degradation KW - Tank for cryogenic goods PY - 2024 AN - OPUS4-60462 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Novel Insulation Concepts for Large Scale Liquefied Hydrogen Storages N2 - The NICOLHy project aims to develop a novel insulation concept based on Vacuum Insulation Panels (VIP) that enables the safe, cost- and energy efficient storage of large quantities of LH2. Such large scale LH2 storage technology is necessary for establishing a hydrogen economy with dimensions between 40.000 m³ and more than 200.000 m³ of LH2. However, new design concepts are needed because the currently available technologies used in small and medium storages today are not suitable for up-scaling. The main problems prohibiting the up-scaling are the long production time due to the process chain, the low failure tolerance and the spherical shape, which reduces the payload in technical applications by up to 50% compared to other shapes. The novel concept will change these conditions by a system which is modular, open-form, time-and cost efficient while production, operation and service, multi-failure tolerant and applicable for onshore and offshore applications. The presentations shows details to the concept and presents several safety concerns the project has to deal with. T2 - ELVHyS - International Stakeholder's Seminars CY - Bologna, Italy DA - 30.09.2024 KW - LH2 KW - Insulation KW - Safety PY - 2024 AN - OPUS4-61208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Grotelüschen, Frank A1 - Eberwein, Robert A1 - Berhorst, Ralf T1 - Supertanker für H2: EU-Projekt konstruiert günstigen Riesenspeicher N2 - Wasserstoff stellt einen potenziellen Energieträger für den großskaligen Import von Energie nach Europa dar. Von seinen verschiedenen Speicherformen eignet sich hierfür insbesondere verflüssigter Wasserstoff, mit dem sich auf gleichem Volumen deutlich mehr Energie speichern lässt als bei der druckbasierten Speicherung. Verflüssigter Wasserstoff wird bei minus 253°C gespeichert und muss für dessen Transport lange bei dieser niedrigen Temperatur gehalten werden. Dies stellt besondere Herausforderungen an die thermische Isolation von Tanks. Der Erforschung nachhaltiger, kosten- und energieeffizienter sowie sicherer thermischen Isolationen wird im NICOLHy Projekt, unter Leitung der BAM, nachgegangen. KW - Verflüssigter Wasserstoff KW - Thermische Isolation PY - 2024 UR - https://www.deutschlandfunk.de/supertanker-fuer-h2-eu-projekt-konstruiert-guenstigen-riesenspeicher-dlf-d50ff14a-100.html PB - Deutschlandradio CY - Hamburg AN - OPUS4-60538 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Chianese, Carmela A1 - Hajhariri, Aliasghar A1 - Eberwein, Robert A1 - Otremba, Frank A1 - Cozzani, Valerio T1 - Modeling the performance of multilayer insulation in cryogenic tanks undergoing external fire scenarios N2 - Multilayer Insulation (MLI) is frequently used in vacuum conditions for the thermal insulation of cryogenic storage tanks. The severe consequences of the degradation of such materials in engulfing fire scenarios were recently evidenced by several large-scale experimental tests. In the present study, an innovative modelling approach was developed to assess the performance of heat transfer in polyester-based MLI materials for cryogenic applications under fire conditions. A specific layer-by-layer approach was integrated with an apparent kinetic thermal degradation model based on thermogravimetric analysis results. The modeling results provided a realistic simulation of the experimental data obtained by High-Temperature Thermal Vacuum Chamber tests reproducing fire exposure conditions. The model was then applied to assess the behavior of MLI systems for liquid hydrogen tanks in realistic fire scenarios. The results show that in intense fire scenarios degradation occurs rapidly, compromising the thermal insulation performances of the system within a few minutes. KW - Multilayer Insulation KW - Cryogenic Vessels KW - Liquefied Hydrogen KW - Liquefied Natural Gas KW - Safety KW - Fire PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-599418 DO - https://doi.org/10.1016/j.psep.2024.04.061 SN - 0957-5820 VL - 186 SP - 1169 EP - 1182 PB - Elsevier B.V. AN - OPUS4-59941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Camplese, D. A1 - Scarponi, G. E. A1 - Cozzani, V. A1 - Otremba, Frank T1 - Insulation Materials Used in Tanks for the Storage of Cryogenic Fluids in Fire Scenarios N2 - The importance of tanks for storing cryogenic fluids in the energy industry is increasing because of ongoing political conflicts and the implementation of more environmentally friendly energy sources. Key representatives for the application of cryogenic tanks are natural gas in the form of Liquefied Natural Gas (LNG) and hydrogen, e. g. in the form of Liquefied Hydrogen (LH2), for which significantly higher transport capacities can be achieved with the same transport volume using cryogenic storages than with storages based solely on overpressure. What applies to all cryogenic transported fluids in common is their condition that must be maintained. Hence heat flows into the preserved fluid must be minimized. Thermal super Insulations (TSI) based on e. g. multilayer insulations (MLI), perlites, and vacuum are utilized for this purpose and have already proven themselves in similar applications. However, for the use of tanks for cryogenic fluids in the transport sector, there is insufficient knowledge regarding the course and consequences of incidents, which is due to the still short period of use and the few documented incidents, hence few investigations carried out in this field. Typical scenarios in the transport sector represent car accidents with collisions, fires, and their combination, which are associated with extraordinary loads on the tank. The focus of this study is to investigate the behavior of TSI as a result of their thermal exposure to a heat source representing a fire. It is worth mentioning that this could lead to an increase of the heat flux into a tank by several orders of magnitude, and to permanent damage of the TSI, ultimately rapid release of flammable gas as well as a Boiling Liquide Expanding Vapour Explosion (BLEVE). For this purpose, a high temperature thermal vacuum chamber (HTTVC) has been developed that allows thermal loading of MLI or perlites in a vacuum and simultaneous measurement of heat flow through this TSI. The HTTVC is designed to represent realistic insulation conditions and to withstand thermal loads from typical design fires. The HTTVC was applied to investigate TSI based on MLI and vacuum. It is shown that the thermal stress caused permanent damage to the TSI, with shrinkage, phase change, pyrolysis, and condensation being significant damage mechanisms. The results are relevant for the evaluation of accident scenarios and can thus contribute to the improvement of TSI and the development of emergency measures for the protection of persons and infrastructures. T2 - ASME 2023 Pressure Vessels & Piping Conference (PVP2023) CY - Atlanta, Georgia, USA DA - 16.07.2023 KW - LH2 KW - LNG KW - MLI KW - Fire PY - 2023 SP - 1 EP - 8 PB - ASME AN - OPUS4-57973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hajhariri, Aliasghar ED - Eberwein, Robert ED - Perrone, Luca pakj ED - Cozzani, Valerio ED - Otremba, Frank ED - Seidlitz, Holger T1 - Study the Impact of Spacer at Thermal Degradation Process of MLI-based Insulation in Fire Condition N2 - To reduce carbon dioxide emissions, energy carries such as hydrogen consider to be a solution. Consumption of hydrogen as a fuel meets several restrictions such as its low volumetric energy density in gas phase. To tackle this problem, storage as well as transportation in liquid phase is recommended. To be able to handle this component in liquid phase, an efficient thermal insulation e.g., MLI insulation is required. Some studies have been revealed vulnerability of this type of insulation against high heat flux, for instance a fire accident. Some investigations have been depicted the importance of consideration of the MLI thermal degradation in terms of its reflective layer. However, limited number of studies have been focused on the thermal degradation of spacer material and its effect on the overall heat flux. In this study, through systematic experimental measurements, the effect of thermal loads on glass fleece, glass paper as well as polyester spacers are investigated. The results are reported in various temperature and heat flux profiles. Interpreting the temperature profiles revealed as the number of spacers in the medium increases, the peak temperature detectable by the temperature sensor on the measurement plate decreases. Moreover, the contribution of each individual spacer in all cases regarding the experimental temperature range is assessed to be around 8%. This value may increase to around 50% for glass paper and polyester spacers, and to around 25% for glass fleece spacers as the number of spacer layers increases up to six layers. To utilize the outcomes of the experiment later and integrate the results into numerical and CFD simulations, a model is proposed for the mentioned experimental temperature range up to 300°C to predict a heat flux attenuation factor. The model proposes a fitting factor that can reproduce the least square fitted line to the experimental data. T2 - 15th International Symposium on Hazards, Prevention, and Mitigation of Industrial Explosions Naples (ISHPMIE) CY - Naples, Italy DA - 10.06.2024 KW - Multi-Layer Insulation KW - Cryogenics KW - Liquid Hydrogen KW - Heat Transfer KW - Hydrogen Storage PY - 2024 SP - 744 EP - 755 AN - OPUS4-60461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Scarponi, Giordano Emrys A1 - Cozzani, Valerio A1 - Otremba, Frank T1 - Lh2 Tanks In Fire Incidents - The Cryogenic High Temperature Thermal Vacuum Chamber Enables In-Depth Insights N2 - Liquefied Hydrogen (LH2) and Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Their storage requires tanks with thermal super-insulations to keep them at cryogenic conditions for a long time. These insulation systems have proven itself in various applications over a long time. However, these insulations are still new in land transportation, where accidents involving collisions, fires, and their combination are to be expected. This study summarizes the results of the ongoing research program in which insulations commonly used in industry were analysed through experimental and numerical studies under fire-like conditions. It was found that there are strong differences among the various insulation systems. Several safety concerns and research gaps exists for layered insulations, which are typically used in land transport. To further analyse these insulation systems, a new test concept called Cryogenic High Temperature Thermal Vacuum Chamber (CHTTVC) was developed and manufactured. This concept enables the testing of large insulation samples under industrial conditions and the consideration of cryogenic conditions relevant for the investigation of various phenomena. The results are important for the evaluation of accident scenarios, the improvement of thermal super-insulations, and the development of emergency measures. T2 - IMECE 2024 CY - Oregon, Portland, USA DA - 17.11.2024 KW - LH2 KW - LNG KW - Fire KW - Insulation KW - Safety PY - 2024 SN - 978-0-7918-8869-8 SP - 1 EP - 7 PB - ASME AN - OPUS4-61751 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, D. A1 - Chianese, C. A1 - Scarponi, G. A1 - Eberwein, Robert A1 - Otremba, Frank A1 - Cozzani, V. T1 - Analysis of high temperature degradation of multi-layer insulation (MLI) systems for liquid hydrogen storage tanks N2 - The interest in hydrogen-based green energy is increasing worldwide, and the same is true for hydrogen-powered vehicles. Among the possible solutions to store hydrogen in such vehicles, cryogenic tanks equipped with multi-layer insulation (MLI) are the most promising to increase the amount of energy stored per unit volume. However, MLI is affected by severe deterioration when exposed to an external source of heat such as a fire following a car accident, leaving the tank unprotected and leading to failure in a relatively short time. In this work, a one-dimensional model to evaluate MLI thermal degradation when a liquid hydrogen tank is exposed to fire is presented. The relevance of taking MLI degradation into account when simulating the pressure increase due to external fire exposure is here demonstrated through the analysis of several case studies. The results show that MLI systems performance depletes within a few minutes of exposure to hydrocarbon poolfire. T2 - ICheaP 16 CY - Naples, Italy DA - 21.05.2023 KW - LH2 KW - MLI KW - Tiefkalt KW - Fire KW - Tank PY - 2023 SN - 2283-9216 VL - 2023 SP - 1 EP - 6 PB - AIDIC Servizi S.r.l. AN - OPUS4-57584 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Wasserstoff - Kryogene Anwendungen N2 - Wasserstoff wird als ein potenzieller alternativer Energieträger gesehen, mit dem die für 2050 gesetzten Klimaziele erreicht werden könnten. Der Transport von Wasserstoff ist mittels verschiedener Speichertechniken möglich, von denen der kryogene Transport mit den größten volumetrischen Energiedichten einhergeht. Hierdurch eignen sich diese Speicher besonders für die energieintensiven Verkehrsmittel im Land-, See- und Flugverkehr. Im Vortrag werden Speichertechniken, Gefahren im Umgang mit kryogenen Gasen sowie bisherige Störfälle dargestellt. Darauf aufbauend wird ein Teil der aktuellen Forschungsarbeit an der BAM vorgestellt, die die Sicherheit dieser Speicher unter außergewöhnlichen Belastungen adressiert. T2 - 26. Gefahrgutkongress Mecklenburg-Vorpommern CY - Rostock, Germany DA - 03.11.2022 KW - Wasserstoff KW - H2 KW - LNG KW - LH2 KW - Tank PY - 2022 AN - OPUS4-56181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, D. T1 - Analysis of high temperature degradation of multi-layer insulation (MLI) systems for liquid hydrogen storage tanks N2 - The interest in hydrogen-based green energy is increasing worldwide, and the same is true for hydrogen-powered vehicles. Among the possible solutions to store hydrogen in such vehicles, cryogenic tanks equipped with multi-layer insulation (MLI) are the most promising to increase the amount of energy stored per unit volume. However, MLI is affected by severe deterioration when exposed to an external source of heat such as a fire following a car accident, leaving the tank unprotected and leading to failure in a relatively short time. In this work, a one-dimensional model to evaluate MLI thermal degradation when a liquid hydrogen tank is exposed to fire is presented. The relevance of taking MLI degradation into account when simulating the pressure increase due to external fire exposure is here demonstrated through the analysis of several case studies. The results show that MLI systems performance depletes within a few minutes of exposure to hydrocarbon poolfire. T2 - ICheaP 16 CY - Naples, Italy DA - 21.05.2023 KW - LH2 KW - MLI KW - Fire KW - Tank PY - 2023 AN - OPUS4-57553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Systems for the storage of cryogenic liquefied gases N2 - Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. The presentation includes 2 main topics of the department. First TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. To analyze fire scenarios a High-Temperature Thermal Vacuum Chamber (HTTVC) was developed that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this chamber, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. In the presentation, the results are presented. Second, the studying of accident scenarios enables the improvement of thermal superinsulation and to find novel insulation concepts. This is necessary for LH2 large-scale storages, for which state-of-the-art solutions are not suitable. Within the presentation, a novel insulation concept will be presented. T2 - Specialist Meeting - Threats to HAZMAT Pressure Vessels and BLEVE CY - Berlin, Germany DA - 25.04.2023 KW - Crygenic KW - LH2 KW - LNG KW - Fire KW - MLI PY - 2023 AN - OPUS4-57414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - LH2 Tanks In Fire Incidents - The Cryogenic High Temperature Thermal Vacuum Chamber Enables In-Depth Insights N2 - Liquefied Hydrogen (LH2) and Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Their storage requires tanks with thermal super-insulations to keep them at cryogenic conditions for a long time. These insulation systems have proven itself in various applications over a long time. However, these insulations are still new in land transportation, where accidents involving collisions, fires, and their combination are to be expected. This study summarizes the results of the ongoing research program in which insulations commonly used in industry were analysed through experimental and numerical studies under fire-like conditions. It was found that there are strong differences among the various insulation systems. Several safety concerns and research gaps exists for layered insulations, which are typically used in land transport. To further analyse these insulation systems, a new test concept called Cryogenic High Temperature Thermal Vacuum Chamber (CHTTVC) was developed and manufactured. This concept enables the testing of large insulation samples under industrial conditions and the consideration of cryogenic conditions relevant for the investigation of various phenomena. The results are important for the evaluation of accident scenarios, the improvement of thermal super-insulations, and the development of emergency measures. T2 - IMECE 2024 CY - Portland, OR, USA DA - 17.11.2024 KW - LH2 KW - LNG KW - Fire KW - Insulation KW - Safety PY - 2024 AN - OPUS4-61752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Otremba, Frank A1 - Cozzani, Valerio T1 - Comparative performance assessment of multilayer insulation (MLI) systems for liquid hydrogen vessels in fire scenarios N2 - Multilayer Insulation (MLI) systems are a mature technology for cryogenic liquid hydrogen (LH2) tank thermal insulation. Recent tests evidenced that MLI materials may be damaged when exposed to fire, resulting in critical safety issues in the case of accidents. Thus, an innovative approach to the performance assessment of aluminum and polyester-based MLIs for LH2 tanks in fire scenarios was developed. A specific model integrating the hightemperature degradation of MLIs and the thermodynamic modeling of the tank lading was coupled to specific key performance indicators. Results of the analysis applied to a vehicle-scale tank equipped with 80 MLI layers indicate that MLI degradation and consequent tank failure may occur in less than 20 min for external shell temperatures above 1160 K in the presence of full engulfment, regardless of insulation used. Conversely, degradation does not occur earlier than 3600s below 603 and 928 K for polyester and aluminum-based MLI, respectively. KW - LH2 KW - LNG KW - Cryogenic storage tank KW - Fire KW - Insulation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630841 DO - https://doi.org/10.1016/j.ijhydene.2025.04.534 SN - 0360-3199 VL - 135 SP - 537 EP - 552 PB - Elsevier Ltd. AN - OPUS4-63084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Otremba, Frank A1 - Camplese, Davide A1 - Scarponi, Giordano E. A1 - Cozzani, Valerio A1 - Seidlitz, Holger T1 - Repeatable testing of a cryogenic storage tank with variable insulation material in fire like conditions N2 - For decarbonizing the energy industry and transport, cryogenic energy carriers have great potential. The storage takes place in tanks with thermal super-insulations, which are in application for decades, but there is only limited knowledge about its behaviour in a fire scenario. This represents a major incident that may generate extraordinary loads on the tank and its insulation system, and that eventually lead to a sudden tank failure. This paper presents a test rig called the Cryogenic High Temperature Thermal Vacuum Chamber (CHTTVC), which can be used to test typical thermal superinsulation’s under cryogenic and fire-like conditions in parallel. The test method makes it possible to measure the heat flow through the thermal superinsulation over time and to investigate the degradation behaviour of the insulation within a test. In the paper results from the first tests are presented. T2 - 18th Cryogenics 2025, IIR Conference CY - Prague, Czech Republic DA - 07.04.2025 KW - LH2 KW - LNG KW - Fire KW - Insulation KW - Safety PY - 2025 DO - https://doi.org/10.18462/iir.cryo.2025.0007 SP - 205 EP - 210 CY - Prag AN - OPUS4-63740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. T1 - Seminar on Smelling Drones – Part 2: Design and Experimental Study of an Nano Aerial Robot for ARO Applications N2 - This seminar series comprises three lectures on drones and ground robots capable of sensing chemical substances and two accompanying hands-on workshops on nano drones equipped with chemical sensors. In the first lecture, Dr. Neumann will talk on a summary of aerial robot olfaction and his research. In the second and third lectures, more details of the nano drones equipped with chemical sensors will be provided, and the participants can get hands on experience of the nano drones in the accompanying workshops. The lectures will be given in English. This seminar series is supported by FY2023 Researcher Exchanges Program in UEC. T2 - Seminar Series on Smelling Drones CY - Tokyo, Japan DA - 28.11.2023 KW - Mobile robotic olfaction KW - Nano aerial robot KW - Gas source localization KW - Setup and Validation KW - Gas distribution mapping PY - 2023 AN - OPUS4-59130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - New concepts in liquid hydrogen storage N2 - On the way to the energy transition, cryogenic fluids such as Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) are very important. They enable the large-scale economic transport and storage of energy as well as they represent alternative fuels for energy-intensive mobile applications such as aircrafts, ships and HGVs. For the last one, the number of vehicles and fuel stations has increased rapidly in the last 10 years all over Europe. Does this also entail new risks, for instance from a BLEVE in case of fires? To answer this question, BAM has conducted several research projects over the last decades and intensified the research recently with several experimental, numerical, and empirical outcomes on how a tank with insulation behaves in a fire. The presentation shows an overview of this research. The findings are relevant for global standardization procedures and to improve the overall safety in chemistry and technics. T2 - Hydrogen Refueling Station Opening CY - Baruth/Mark, Germany DA - 03.07.2025 KW - LH2 KW - Insulation KW - Fire KW - LNG KW - Safety PY - 2025 AN - OPUS4-63628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eberwein, Robert A1 - Heßmann, Jennifer A1 - Werner, Jan A1 - Scarponi, Giordano Emrys A1 - Cozzani, Valerio A1 - Otremba, Frank T1 - Investigation of Realistic Fire Scenarios Involving Cryogenic Storage Tanks N2 - The number of vehicles using or transporting cryogenic fuels such as Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) increases fast in the land transportation sector. Does this also entail new risks for instance from a BLEVE? A key to answer this question is to research representative fires by its characterization and its effect on the insulation. At BAM’s technical test side in Germany, a test series was started to answer this question among others. This paper presents results on a pool fire under a colorimeter, that simulates a tank. The investigation points out, that the full fire characterization approach allows to represent the fire. The findings are relevant for the investigation of a representative design fire that is applicable for the approval and improvement of tanks as well as to research accident scenarios and their consequences. T2 - Loss Prevention 2025 CY - Bologna, Italien DA - 09.06.2025 KW - LH2 KW - LNG KW - Fire KW - Tank KW - Safety PY - 2025 DO - https://doi.org/10.3303/CET25116031 SN - 2283-9216 IS - 116 SP - 181 EP - 186 PB - AIDIC AN - OPUS4-63738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - INPR A1 - Nerger, Tino A1 - Neumann, Patrick P. A1 - Weller, Michael G. T1 - Drone-Based Localization of Hazardous Chemicals by Passive Smart Dust N2 - The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as Smart Dust. Several efforts focused primarily on computing and networking capabilities but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data was processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios. N2 - Die Verteilung winziger Sensoren über ein bestimmtes Gebiet wurde erstmals Ende der 1990er Jahre als Konzept namens „Smart Dust“ vorgeschlagen. Mehrere Bemühungen konzentrierten sich hauptsächlich auf Rechen- und Netzwerkfähigkeiten, stießen jedoch schnell auf Probleme im Zusammenhang mit der Stromversorgung, den Kosten, der Datenübertragung und der Umweltverschmutzung. Um diese Einschränkungen zu überwinden, schlagen wir die Verwendung von papierbasierten (konfettiartigen) Chemosensoren vor, die die inhärente Selektivität chemischer Reagenzien, wie z. B. kolorimetrischer Indikatoren, nutzen. In dieser Arbeit konnten günstige und biologisch abbaubare passive Sensoren aus Zellulose erfolgreich das Vorhandensein gefährlicher Chemikalien, z.B. starker Säuren, durch eine deutliche Farbänderung anzeigen. Eine herkömmliche Farb-Digitalkamera, die an einer Drohne befestigt ist, konnte dies aus sicherer Entfernung leicht erkennen. Die gesammelten Daten wurden verarbeitet, um den Gefahrenbereich zu abzugrenzen. Unsere Arbeit stellt eine Kombination aus dem Smart-Dust-Konzept, Chemosensorik, papierbasierter Sensortechnologie und kostengünstigen Drohnen für eine flexible, empfindliche, wirtschaftliche und schnelle Erkennung gefährlicher Chemikalien in Hochrisikoszenarien dar. KW - Confetti KW - Remote sensing KW - Drones KW - UAV KW - Optical detection KW - Chemosensor KW - pH indicator KW - Paper-based sensors KW - Harmful chemicals KW - Chemical desaster PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-621284 DO - https://doi.org/10.20944/preprints202408.0030.v1 SP - 1 EP - 17 PB - MDPI CY - Basle, Switzerland AN - OPUS4-62128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michalchuk, Adam T1 - The Mechanochemical Excitation of Crystalline LiN3 N2 - Mechanochemical reactions are driven by the direct absorption of mechanical energy by a solid (often crystalline) material. Understanding how this energy is absorbed and ultimately causes a chemical transformation is essential for understanding the elementary stages of mechanochemical transformations. Using as a model system the energetic material LiN3 we here consider how vibrational energy flows through the crystal structure. By considering the compression response of the crystalline material we identify the partitioning of energy into an initial vibrational excitation. Subsequent energy flow is based on concepts of phonon–phonon scattering, which we calculate within a quasi-equilibrium model facilitated by phonon scattering data obtained from Density Functional Theory (DFT). Using this model we demonstrate how the moments (picoseconds) immediately following mechanical impact lead to significant thermal excitation of crystalline LiN3, sufficient to drive marked changes in its electronic structure and hence chemical reactivity. This work paves the way towards an ab initio approach to studying elementary processes in mechanochemical reactions involving crystalline solids. KW - Energetic materials KW - Ab initio simulation KW - DFT KW - Mechanochemistry PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-559310 DO - https://doi.org/10.1039/d2fd00112h SP - 1 EP - 20 PB - Royal Society of Chemistry AN - OPUS4-55931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hernández García, María Amparo T1 - SAF-based optical biosensor with 3D-printed free-form optics for targeted explosives immuno-detection N2 - Guaranteeing safety and security of citizens requires a significant effort and innovative tools from national and international agencies and governments, especially when it comes to the field of explosives detection. The need to detect Improvised Explosive Devices (IEDs) and Home-made Explosives (HMEs) at a point of suspicion, has grown rapidly due to the ease with which the precursors can be obtained and the reagents synthesised. The limited availability of immunoanalytical tools for HME detection presents an opportunity for the development of new devices, which enable a rapid detection and recognise the target analyte with high specificity and sensitivity. In this work, we introduce an optical biosensor for highly specific and sensitive HME detection. The immunoassay system is placed in a hydrogel environment permeable to the analyte and transparent to light interrogating the fluorescently labelled antibodies. The readout of the immunoanalytical system is realized with Supercritical Angle Fluorescence (SAF), an advanced microscopy technique. To accomplish this, we made use of recent, commercial high resolution (< 22 µm) Liquid Crystal Display 3D printers to fabricate a parabolic optical element with high refractive index (RI>1.5) and transmission values (>90%) from photo-resin. Aiming at a new generation of sensors, which not only can meet the requirements of trace detection, but can also be used for substance identification, the combination of immunoanalytical recognition with SAF detection offers a modularity and versatility that is principally well suitable for the measurements of target analytes at trace levels. T2 - 8th International conference in Biosensing Technology CY - Seville, Spain DA - 12.05.2024 KW - 3D printing KW - Biosensor KW - Fluorescence KW - Explosives PY - 2024 AN - OPUS4-60561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hernandez Garcia, Maria Amparo T1 - Optical biosensor using free form prototyped elements for targeted explosives immunodetection N2 - Ensuring the safety and security of citizens necessitates a considerable investment of resources and the development of innovative tools by national and international agencies and governments, particularly in the context of explosives detection [1]. The necessity for the detection of improvised explosive devices (IEDs) and homemade explosives (HMEs) at the point of suspicion has increased exponentially due to the simplicity with which the precursors can be obtained, and the reagents synthesised. The restricted availability of immunoanalytical instruments for the detection of homemade explosives (HMEs) offers a valuable opportunity for the development of innovative devices that can rapidly identify and recognise the target analyte with high specificity and sensitivity [2]. In this study, we present the development of an optical biosensor for highly specific and sensitive HME detection. The immunoassay system is situated within a matrix that is permeable to the target analyte and transparent to light, which enables the interrogation via fluorescence. The immunoanalytical system's readout is achieved through the utilisation of supercritical angle fluorescence (SAF), an advanced microscopy technique. To this end, we employed recent, commercially available high-resolution (less than 22 μm) liquid crystal display SLA printers to fabricate a free-form parabolic optical element with a high refractive index (RI greater than 1.5) and transmission values exceeding 90% from commercial photo-resins. The objective is to develop a new generation of sensors that can not only meet the requirements of trace detection but also be used for substance identification. The combination of immunoanalytical recognition with SAF detection offers a modular and versatile solution that is particularly well suited to the measurement of target analytes at trace levels. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Biosensor KW - SAF KW - Free-form optics KW - 3D printing KW - Security PY - 2025 AN - OPUS4-62802 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steglich, Patrick A1 - Paul, Martin A1 - Mai, C. A1 - Böhme, A. A1 - Bondarenko, S. A1 - Weller, Michael G. A1 - Mai, A. T1 - A monolithically integrated microfluidic channel in a silicon-based photonic-integrated-circuit technology for biochemical sensing N2 - In this work, a cost-effective optofluidic system is proposed and preliminary experimental results are presented. A microfluidic channel monolithically integrated into a photonic integrated circuit technology is used in conjunction with a cyclic olefin copolymer (COC) substrate to provide fluidic in- and output ports. We report on initial experimental results as well as on the simple and cost-effective fabrication of this optofluidic system by means of micro-milling. KW - Biosensors KW - Biophotonics KW - Optical sensors KW - Photonic sensors KW - Ring resonators KW - Silicon photonics KW - Lab-on-a-chip KW - Microfluidics KW - Chip KW - Biochip PY - 2021 DO - https://doi.org/10.1117/12.2588791 VL - 11772 SP - 1 EP - 5 PB - SPIE AN - OPUS4-53559 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Martin T1 - Development of a high-sensitivity biosensor for the quasi-continuous detection of the explosive TNT and the illegal drug cocaine N2 - An immunofluorometric biosensor with laser-induced fluorescence detection was presented. For TNT an LOD of 60 ppb and for cocaine an LOD of 9 ppb was achieved. A swipe test was performed in less than 3 minutes. No significant cross-reactivity was observed. T2 - 15. Interdisziplinäres Doktorandenseminar des Arbeitskreises Prozessanalytik der GDCh CY - Online meeting DA - 06.09.2021 KW - PETN KW - HMX KW - RDX KW - Microfluidic mixing KW - Lab-on-a-chip KW - Affinity column KW - Monolithic material KW - Sintered glass KW - Dy-654 KW - Flowcell KW - Epifluorescence KW - CMOS camera KW - Diode laser KW - Antibody screening PY - 2021 AN - OPUS4-53329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paul, Martin A1 - Tscheuschner, Georg A1 - Herrmann, Stefan A1 - Weller, Michael G. T1 - Fast Detection of 2,4,6-Trinitrotoluene (TNT) at ppt Level by a Laser-Induced Immunofluorometric Biosensor N2 - The illegal use of explosives by terrorists and other criminals is an increasing issue in public spaces, such as airports, railway stations, highways, sports venues, theaters, and other large buildings. Security in these environments can be achieved by different means, including the installation of scanners and other analytical devices to detect ultra-small traces of explosives in a very short time-frame to be able to take action as early as possible to prevent the detonation of such devices. Unfortunately, an ideal explosive detection system still does not exist, which means that a compromise is needed in practice. Most detection devices lack the extreme analytical sensitivity, which is nevertheless necessary due to the low vapor pressure of nearly all explosives. In addition, the rate of false positives needs to be virtually zero, which is also very difficult to achieve. Here we present an immunosensor system based on kinetic competition, which is known to be very fast and may even overcome affinity limitation, which impairs the performance of many traditional competitive assays. This immunosensor consists of a monolithic glass column with a vast excess of immobilized hapten, which traps the fluorescently labeled antibody as long as no explosive is present. In the case of the explosive 2,4,6-trinitrotoluene (TNT), some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and chip-based mixing-devices and flow-cells. The system achieved limits of detection of 1 pM (1 ppt) of the fluorescent label and around 100 pM (20 ppt) of TNT. The total assay time is less than 8 min. A cross-reactivity test with 5000 pM solutions showed no signal by pentaerythritol tetranitrate (PETN), 1,3,5-trinitroperhydro-1,3,5-triazine (RDX), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX). This immunosensor belongs to the most sensitive and fastest detectors for TNT with no significant cross-reactivity by non-related compounds. The consumption of the labeled antibody is surprisingly low: 1 mg of the reagent would be sufficient for more than one year of continuous biosensor operation. KW - Airport KW - Aviation KW - Bombs KW - Terrorism KW - Biosensing KW - Continuous Sensor KW - High-Speed KW - Ultrasensitive PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-511245 DO - https://doi.org/10.3390/bios10080089 VL - 10 IS - 8 SP - 89 PB - MDPI CY - Basel AN - OPUS4-51124 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - INPR A1 - Paul, Martin A1 - Tannenberg, Robert A1 - Tscheuschner, Georg A1 - Ponader, Marco A1 - Weller, Michael G. T1 - Cocaine detection by a laser-induced immunofluorometric biosensor N2 - The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement. KW - Drug search KW - Customs KW - Confiscation KW - Border surveillance KW - Narcotics KW - International drug trade KW - Drug trafficking KW - Illicit drug KW - Immunosensor KW - Antibodies KW - Detection PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-529951 DO - https://doi.org/10.20944/preprints202107.0521.v1 SN - 2310-287X N1 - Geburtsname von Ponader, Marco: Wilke, M. - Birth name of Ponader, Marco: Wilke, M. SP - 1 PB - MDPI CY - Basel AN - OPUS4-52995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kosareva, E. A1 - Gainutdinov, R. A1 - Michalchuk, Adam A1 - Ananyev, I. A1 - Muravyev, N. T1 - Mechanical Stimulation of Energetic Materials at the Nanoscale N2 - The initiation of energetic materials by mechanical stimuli is a critical stage of their functioning, but remains poorly understood. Using atomic force microscopy (AFM) we explore the microscopic initiation behavior of four prototypical energetic materials: 3,4-dinitropyrazole, 𝜖-CL-20, 𝛼-PETN and picric acid. Along with the various chemical structures, these energetic compounds cover a range of application types: a promising melt-cast explosive, the most powerful energetic compound in use, a widespread primary explosive, and a well-established nitroaromatic explosive from the early development of energetics. For the softest materials (picric acid and 3,4-dinitropyrazole), the surfaces were found to behave dynamically, quickly rearranging in response to mechanical deformation. The pit created by nanoscale friction stimulation on the surface of 3,4-dinitropyrazole doubled in volume upon aging for half an hour. Over the same time frame, a similar pit on picric acid surface increased in volume by more than seven-fold. Remarkably, increased humidity was found to reduce the rate of surface rearrangement, potentially offering an origin for the desensitization of energetic materials when wetted. Finally, we identify an inverse correlation between the surface dynamics and mechanical sensitivity of our test energetic compounds. This strongly suggests that surface dynamics influence a material’s ability to dissipate excess energy, acting as a buffer towards mechanical initiation. KW - Energetic materials KW - Mechanical Properties KW - Mechanical Sensitivity PY - 2022 DO - https://doi.org/10.1039/D2CP00832G VL - 24 IS - 15 SP - 8890 EP - 8900 PB - Royal Society of Chemistry AN - OPUS4-54562 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Aree, T. A1 - McMonagle, C. J. A1 - Michalchuk, Adam A1 - Chernyshov, D. T1 - Low-frequency lattice vibrations from atomic displacement parameters of a-FOX-7, a high energy density material N2 - Highly anharmonic thermal vibrations may serve as a source of structural instabilities resulting in phase transitions, chemical reactions and even the mechanical disintegration of a material. Ab initio calculations model thermal motion within a harmonic or sometimes quasi-harmonic approximation and must be complimented by experimental data on temperature-dependent vibrational frequencies. Here multi-temperature atomic displacement parameters (ADPs), derived from a single-crystal synchrotron diffraction experiment, are used to characterize low-frequency lattice vibrations in the alpha-FOX-7 layered structure. It is shown that despite the limited quality of the data, the extracted frequencies are reasonably close to those derived from inelastic scattering, Raman measurements and density functional theory (DFT) calculations. Vibrational anharmonicity is parameterized by the Grüneisen parameters, which are found to be very different for in-layer and out-of-layer vibrations. KW - Energetic Materials KW - DFT KW - Structural dynamics KW - X-ray diffraction PY - 2022 DO - https://doi.org/10.1107/S2052520622002700 SN - 2052-5206 VL - 78 SP - 376 EP - 384 PB - Wiley-Blackwell CY - Oxford AN - OPUS4-54832 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michalchuk, Adam A1 - Morrison, C. T1 - From lattice vibrations to molecular dissociation N2 - The ease with which an energetic material can be initiated by mechanical impact is a critical parameter directing material safety and application. While impact sensitivity metrics are traditionally derived experimentally, recent developments have highlighted that the phenomenon is amenable to first principles simulation. In this chapter, we will outline a fully ab initio approach to predict the relative impact sensitivities of energetic materials based on the mechanochemical principles that link the impact event to vibrational energy transfer. This mechanism is key to rationalizing how a mechanical impact—which deposits energy into the low-frequency lattice vibrations—results in a molecular response. By simulating the vibrational energy levels (the so-called phonon density of states, PDOS) using first-principles computational methods (typically dispersion-corrected plane-wave density functional theory, PW-DFT) we can calculate the relative rate of energy propagation from the delocalized low-energy lattice vibrations through to the localized molecular modes. The latter traps the energy, which eventually results in bond rupture through heightened vibrational excitation. This method, based on vibrational up-pumping, offers a route toward predicting the impact sensitivities of a broad range of energetic materials, provided the crystal structure of the compound (or salt or co-crystal) is known. While it does not offer insight into the sensitizing roles undoubtedly played by crystal defects or grain boundaries, it does provide a level of understanding at the molecular and crystal packing levels. Correspondingly, this approach offers a feedback mechanism to chemists and materials scientists to guide the design of new materials with desired impact sensitivity behavior. KW - Energetic materials KW - Density functional theory KW - Material design PY - 2022 DO - https://doi.org/10.1016/B978-0-12-822971-2.00010-3 VL - 22 SP - 215 EP - 232 PB - Elsevier B.V. AN - OPUS4-54717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -