TY - CONF A1 - Hofmann-Böllinghaus, Anja T1 - Feuer und Rauchausbreitung in Busdepots, Brandverhalten von Bussen N2 - Präsentation zur Problemen der Brandsicherheit bei Busdepots und Empfehlungen zur Verbesserung der Brandsicherheit. T2 - Brandschutz von Bus-Betriebshöfen CY - Cologne, Germany DA - 02.05.2023 KW - Brandschutz PY - 2023 AN - OPUS4-57416 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Hongyi A1 - Hofmann-Böllinghaus, Anja T1 - TREEADS - Experimente und numerische Simulation zur Brandausbreitung von Vegetationsbränden N2 - Um die Ausbreitungsmechanismen von Vegetationsbränden und besonders bei Bodenbränden besser zu verstehen, wurden die Einflussfaktoren auf die Brandausbreitung näher untersucht. Da die Brandausbreitung auch in starkem Maße von der lokalen Vegetation abhängt, war eine Charakterisierung der lokalen Vegetation und der Bodenverhältnisse wichtig. Die Wetterverhältnisse spielen einerseits im Vorfeld des Brandes durch längere Dürreperioden als auch während des Brandes, z.B. durch den Windeinfluss, zusätzlich eine große Rolle. Durch die numerische Simulation kann eine größere Variation der Einflussgrößen abgebildet werden als durch die zeitlich und finanziell begrenzten experimentellen Möglichkeiten. Für die Berechnungen wird der Fire Dynamic Simulators (FDS) mit dem Paket WFDS verwendet. Dadurch kann mit einem vereinfachten 3-Phasen-Reaktionskinetikmodell, bestehend aus Dehydrierung, Pyrolyse, Kohleoxidation, die Ausbreitung von Vegetationsbränden verschiedener Waldbodenarten untersucht werden. Es wurden dazu 6 typische Pflanzenarten und Bodenproben aus Kiefern-, Buchen und Eichenbeständen ausgewählt. Die gesammelten Waldbodenproben wurden alle hinsichtlich des Wassergehalts, des organischen Gehalts, der Packungsdichte, der Dichte und der statistisch ermittelten Pflanzenartenverteilung charakterisiert. Das kinetische Abbrandverhalten wurde durch Thermogravimetrische Analyse (TGA) untersucht. Alle diese Daten wurden als Eingabeparameter für die Simulation verwendet. Die numerischen Simulationen werden mit Experimenten im kleinen, mittleren und Real-Maßstab validiert. T2 - 70. Jahresfachtagung der Vereinigung zur Förderung des Deutschen Brandschutzes CY - Magdeburg, Germany DA - 06.05.2024 KW - Waldbrand KW - Simulation KW - FDS PY - 2024 SN - 978-3-936050-38-7 SP - 321 EP - 336 PB - VdS CY - Köln ET - 2 AN - OPUS4-60258 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Forschung zum Thema Feuer an der BAM N2 - Feuer und deren Auswirkung stellen ein Querschnittsthema über die Aktivitätsfelder der BAM dar. Schwerpunkte stellen dabei Brände in Gebäuden, Industrieanlagen und Lagerräumen, der Vegetation, an Fahrzeugen und Tanks sowie Brände im Zusammenhang mit neuen Energieträgern dar. Im Vortrag werden die einzelnen Themen und exemplarische für deren Erforschung nutzbare Infrastruktur vorgestellt. T2 - Transfer on Fire 2 CY - Luckenwalde, Germany DA - 10.07.2025 KW - Feuer KW - Brandlasten PY - 2025 AN - OPUS4-63686 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hofmann-Böllinghaus, Anja A1 - Anderson, J. T1 - Editorial: Special issue facades N2 - Facade fires are of growing concern worldwide. Severe facade fires in different parts of the world as well as activities in many countries regarding the testing of facades show the urgency of the fire safety challenges in façade fires. The need for knowledge and a wide Archive of work in this area has become evident after recent incidents which involved extensive facade fires. These include the tragic fires in Dubai and Grenfell Tower in 2017 in the United Kingdom. In many cases, the widespread live news coverage of the events and size of These fires has emphasized the need for progress in the understanding of the processes involved in these fires and put pressure upon the fire safety engineering community to find effective solutions. KW - Facade fire PY - 2021 DO - https://doi.org/10.1002/fam.3001 SN - 0308-0501 SN - 1099-1018 VL - 45(5) IS - Special issue: Facade fire safety SP - 585 PB - Wiley CY - Oxford AN - OPUS4-53093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Hongyi T1 - Influence of local vegetation on ignition and fire spread of vegetation fires-Experimental and numerical approach N2 - To investigate the influence of local vegetation, it goes through two aspects. One is laboratory study, the local vegetation samples were collected and tested for the thermal properties, such as activation energy, heat content and reaction kinetic of pyrolysis and dehydration. At the same time, small and medium scale combustion experiments were conducted to investigate the burning behavior. The other aspect is using the thermal properties as the input parameters for the development of numerical simulation in the computational fluid dynamics (CFD) tool. These models were then be validated with the combustion experiments, as a baseline for the further scaling up of the models, in order to investigate how the parameters influencing the fire spread in a large-scale case numerically. T2 - Interflam 2025, 16th International Fire Science and Engineering Conference CY - London, United Kingdom DA - 30.06.2025 KW - Wildfire PY - 2025 AN - OPUS4-63933 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tóth, Péter A1 - Hofmann‐Böllinghaus, Anja A1 - Dumont, Fabien A1 - Anderson, Johan A1 - Sjöström, Johan A1 - Bergius, Mikael A1 - Chiva, Roman A1 - Lalu, Octavian T1 - Finalisation of the European Approach to Assess the Fire Performance of Facades—Brief Information on the Outcome of the Project N2 - This research was conducted within the framework of project SI2.825082, funded by the European Commission—DG GROW. The project's objective was to finalise a European approach for assessing the fire performance of façades under medium and large fire exposure conditions. The national standards BS 8414‐1:2020/BS 8414‐2:2020 and DIN 4102‐20:2017 served as the foundation for developing the new assessment method. As part of the project, a theoretical round robin, initial testing activities and a large‐scale experimental round robin were carried out. The theoretical round robin aimed to examine how different laboratories interpreted the preliminary assessment method. Subsequently, the initial testing phase explored the design of the fire source, combustion chamber and secondary opening. The experimental round robin involved testing four façade systems across three laboratories using the assessment method documents, resulting in 12 tests for medium‐scale and 12 for large‐scale exposure—24 tests in total. These tests provided data to develop a calibration scheme and define appropriate performance criteria for classification. In this paper, the representatives of the project consortium summarise the research process and outline the proposed testing and evaluation methodology, which is intended to form the foundation of a future European testing standard for façades. The article also highlights the need for further research to establish rules for extended application of test results. KW - Facade KW - Testing PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654731 DO - https://doi.org/10.1002/fam.70042 SN - 0308-0501 SP - 1 EP - 27 PB - John Wiley & Sons Ltd. AN - OPUS4-65473 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neugum, Tim T1 - Application of the substructure method to assess the fire resistance of thermally restrained columns N2 - Usually, the fire resistance of load-bearing structural elements is determined by single members testing. A mechanical load is applied to the member in a force-controlled manner and is maintained constant throughout the fire test. After applying the mechanical load, the thermal exposure starts according to the ISO 834 fire curve. In this conventional test method, no interaction between the tested member and the entire building structure is considered. In buildings, the surrounding structure can restrain the thermal expansion of a member in case of fire. This may have both positive and negative effects on the fire resistance of this structural element. Several years ago, the Institute for Sustainability and Innovation in Structural Engineering (ISISE) at the University of Coimbra in Portugal and the Bundesanstalt für Materialforschung und -prüfung (BAM) in Germany carried out fire tests on circular and square steel-reinforced concrete columns with restrained thermal expansion. BAM´s column test furnace allows the specimen to be subjected to thermal exposure and mechanical loading simultaneously. In addition, this device has a substructure test module, which can also provide restrained test conditions. In an ongoing research project at BAM and Technische Universität Braunschweig, the effect of restrained test conditions on the behaviour of steel-reinforced columns under fire exposure is further investigated. The comprehensive test programme of the project includes 14 steel-reinforced concrete columns. Several parameters are varied, i.e., the stiffness representing the surrounding structure of the column, the load level, the eccentricity of the applied load, and the fire exposure to be used. The selection of parameters is based on a real building case study. Furthermore, material tests are carried out to characterize the mechanical properties of the concrete at elevated temperatures, to be included in a numerical simulation. T2 - Vortrag an der Helmut-Schmidt-Universität der Bundeswehr in Hamburg CY - Hamburg, Germany DA - 27.01.2026 KW - Fire tests KW - Steel-reinforced concrete columns KW - Thermal constraint KW - Substructure method KW - Numerical simulation PY - 2026 AN - OPUS4-65431 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tabaka, Weronika A1 - Timme, Sebastian A1 - Lauterbach, Tobias A1 - Medina, L. A1 - Berglund, L. A. A1 - Carosio, F. A1 - Duquesne, S. A1 - Schartel, Bernhard T1 - Bench-scale fire stability testing - Assessment of protective systems on carbon fibre reinforced polymer composites N2 - Fire resistance testing of components made of carbon fibre reinforced polymers (CFRP) usually demands intermediate-scale or full-scale testing. A bench-scale test is presented as a practicable and efficient method to assess how different fire protective systems improve the structural integrity of CFRPs during fire. The direct flame of a fully developed fire was applied to one side of the CFRP specimen, which was simultaneously loaded with compressive force. Three different approaches (film, non-woven, and coatings) were applied: paper with a thickness in the range of μm consisting of cellulose nanofibre (CNF)/clay nanocomposite, nonwoven mats with thickness in the range of cm and intumescent coatings with a thickness in the range of mm. The uncoated specimen failed after just 17 s. Protection by these systems provides fire stability, as they multiply the time to failure by as much as up to 43 times. The reduced heating rates of the protected specimens demonstrate the reduced heat penetration, indicating the coatings’ excellent heat shielding properties. Bench-scale fire stability testing is shown to be suitable tool to identify, compare and assess different approaches to fire protection. KW - Fire stability KW - Bench-scale fire resistance KW - Carbon fibre reinforced polymer KW - Protective coatings PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-532401 DO - https://doi.org/10.1016/j.polymertesting.2021.107340 SN - 0142-9418 SN - 1873-2348 VL - 102 SP - 7340 PB - Elsevier CY - Amsterdam AN - OPUS4-53240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jauregui Rozo, Maria A1 - Sunder, S. A1 - Tabaka, Weronika A1 - Klaffke, Benjamin A1 - Ruckdäschel, H. A1 - Schartel, Bernhard T1 - Unveiling aluminum diethyl phosphinate dual identity: Transfer from epoxy resins to glass fiber-reinforced composites N2 - This study examines the transfer of the flame-retardant aluminum diethyl phosphinate (AlPi) from epoxy resins to composites and the impact of AlPi on fire behavior and fire stability. Further, the effects of different particle sizes and the addition of zinc hydroxy stannate (ZHS) and inorganic silicate (InSi) are investigated. The research provides a detailed analysis of the fire behavior, fire stability, pyrolysis, flame-retardant modes of action, and flame retardancy index. Interestingly, the particle sizes did not significantly affect the flammability, fire behavior, or fire stability in the systems investigated. AlPi acts primarily in the gas phase, releasing phosphorus that yields flame inhibition. Adding glass fibers (GFs) to the epoxy resin boosts the flame retardancy in the condensed phase, reducing the heat release rate (HRR), total heat release (THR), and peak heat release rate (PHRR) by about 60%. This improvement is largely due to replacing fuel and forming a protective layer during burning. Despite the differences between thermoset and composite, the study demonstrates an effective transfer of flame-retardant properties from epoxy resins to fiber-reinforced composites, significantly enhancing the flame retardancy performance in both material systems. KW - Aluminum diethyl phosphinate KW - Epoxy resins KW - Fire behavior KW - Fire stability KW - Gas-phase active KW - Glass fiber-reinforced composites KW - Particle sizes PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-643013 DO - https://doi.org/10.1002/pc.29911 SN - 1548-0569 SN - 0272-8397 VL - 46 IS - 14 SP - 12981 EP - 12999 PB - Wiley AN - OPUS4-64301 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tabaka, Weronika A1 - Meinel, Dietmar A1 - Schartel, Bernhard T1 - Sacrifice Few to Save Many: Fire Protective Interlayers in Carbon- Fiber-Reinforced Laminates N2 - The fire protection of carbon-fiber-reinforced polymer (CFRP) laminates often relies on flame-retardant coatings, but in some applications, their efficacy may diminish upon direct fire exposure due to rapid pyrolysis. This study introduces an innovative approach by integrating protective interlayers within the laminate structure to enhance the fire resistance. Various materials, including ceramic composite WHIPOX, titanium foil, poly(etherimide) (PEI) foil, basalt fibers, rubber mat, and hemp fibers, were selected as protective interlayers. These interlayers were strategically placed within the laminate layout to form a sacrificial barrier, safeguarding the integrity of the composite. Bench-scale fire resistance tests were conducted, where fire (180 kW/m2) was applied directly to the one side of the specimen by a burner while a compressive load was applied at the same time. Results indicate significant prolongation of time to failure for CFRP laminates with protective interlayers, which is up to 10 times longer. This innovative approach represents a potential advance in fire protection strategies for CFRP laminates, offering improved resilience against fire-induced structural failure. KW - Composites in fire KW - Fire resistance KW - Fire retardant interlayers KW - Laminate design KW - Carbon fibre reinforced PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601943 DO - https://doi.org/10.1021/acsomega.4c01408 SN - 2470-1343 VL - 9 IS - 22 SP - 23703 EP - 23712 PB - ACS AN - OPUS4-60194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tabaka, Weronika T1 - Bench-scale fire stability testing - Protective layers in carbon fibre reinforced polymer laminates N2 - Fire resistance testing of components made of carbon fibre reinforced polymers (CFRP) composites usually demands intermediate-scale or full-scale testing. In this study, a bench-scale test is presented as a practicable and efficient method to assess the improvement in structural integrity of CFRP with different protective interlayers during fire. T2 - International Conference on Composite Materials (ICCM23) CY - Belfast, UK DA - 30.07.2023 KW - Fire resistance KW - Bench-scale testing KW - Carbon fibre reinforced polymer composite PY - 2023 AN - OPUS4-58099 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Small but Great – Multifunctional Graphene in Rubber Nanocomposites N2 - A few layer/multilayer graphene (MLG) with a specific surface area of BET ≥ 250 m2/g is proposed as an efficient multifunctional nanofiller for rubbers. The preparation method, i.e., ultrasonically-assisted solution or latex premixing of master batches followed by conventional two-roll milling, strongly influences the dispersion in the elastomeric matrix and is fundamental for the final properties. When homogenously dispersed, single stacks of only approximately 10 graphene sheets, with an aspect ratio of ca. 35, work at low loadings, enabling the replacement of large amounts of carbon black (CB), an increase in efficiency, and a reduction in filler load. The appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing, gas barrier properties, electrical and thermal conductivity, as well as mechanical properties of different rubbers, as shown for chlorine-Isobutylene-Isoprene rubber (CIIR), nitrile-butadiene rubber (NBR), natural rubber (NR), and styrene-butadiene rubber (SBR).[1-5] 3 phr of MLG tripled the Young’s modulus of CIIR, an effect equivalent to 20 phr of CB. The stronger interactions between MLG and NR or SBR also resulted in a reduction in the elongation at break by 20% and 50%, respectively, while the same parameter was hardly changed for CIIR/MLG and NBR/MLG. CIIR/MLG and NBR/MLG were stiffer but just as defomable than CIIR and NBR. The strong reinforcing effect of 3 phr MLG was confirmed by the increase of greater than 10 Shore A in hardness. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards flammability. We investigated MLG also as a synergist for reducing the aluminium trihydrate loading in flame retardant hydrogenated acrylonitrile-butadiene (HNBR), polybutadiene chloroprene (BR/CR), and chlorosulfonated polyethylene rubber(CSM).[6-8] The higher the nanofiller concentration is, the greater the improvement in the properties. For instance, the permeability decreased by 30% at 3 phr of MLG, 50% at 5 phr and 60% at 10 phr, respectively. Moreover, the MLG nanocomposites improve stability of mechanical properties against the effects of weathering. In key experiments an increase in UV-absorption and a pronounced radical scavenging were proved as stabilizing mechanisms. In a nutshell, MLG is an efficient multifunctional nanofiller ready to be used for innovative rubber development. T2 - 34th PDDG Conference CY - Dubrovnik, Croatia DA - 11.06.2023 KW - Graphene KW - Nanocomposites KW - Reinforcement KW - Antioxydant KW - Flame retardant KW - Durability PY - 2023 AN - OPUS4-57693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Multifunctional Elastomer/Graphene Nanocomposites N2 - A few layer/multilayer graphene (MLG) with a specific surface area of BET=250 m2/g is proposed as an efficient multifunctional nanofiller for rubbers. The preparation method, i.e., ultrasonically-assisted solution mixing of master batches followed by two-roll milling, strongly influences the dispersion in the elastomeric matrix and is fundamental for the final properties. When homogenously dispersed, single stacks of only approximately 10 graphene sheets, with an aspect ratio of 34, work at low loadings, enabling the replacement of large amounts of carbon black (CB), an increase in efficiency, and a reduction in filler load. The appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing, gas barrier properties, electrical and thermal conductivity, as well as mechanical properties of different rubbers, as shown for chlorine-Isobutylene-Isoprene rubber (CIIR), nitrile-butadiene rubber (NBR), natural rubber (NR), and styrene-butadiene rubber (SBR). 3 phr of MLG tripled the Young’s modulus of CIIR, an effect equivalent to 20 phr of CB. The stronger interactions between MLG and NR or SBR also resulted in a reduction in the elongation at break by 20% and 50%, respectively, while the same parameter was hardly changed for CIIR/MLG and NBR/MLG. CIIR/MLG and NBR/MLG were stiffer but just as defomable than CIIR and NBR. The strong reinforcing effect of 3 phr MLG was confirmed by the increase of greater than 10 Shore A in hardness. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards flammability, the latter shown by the reduction in heat release rate in the cone calorimeter. We investigated MLG also as a synergist for reducing the aluminium trihydrate loading in flame retardant hydrogenated acrylonitrile-butadiene (HNBR), polybutadiene chloroprene (BR/CR), and chlorosulfonated polyethylene rubber(CSM). The higher the nanofiller concentration is, the greater the improvement in the properties. For instance, the permeability decreased by 30% at 3 phr of MLG, 50% at 5 phr and 60% at 10 phr, respectively. Moreover, the MLG nanocomposites improve stability of mechanical properties against the effects of weathering. In key experiments an increase in UV-absorption and a pronounced radical scavenging were proved as stabilizing mechanisms. In a nutshell, MLG is an efficient multifunctional nanofiller ready to be used for innovative rubber development. T2 - 19th European Polymer Congress, EPF 2022 CY - Prague, Czech Republic DA - 26.06.2022 KW - Graphene KW - Nanocomposite KW - Rubber KW - Elastomer PY - 2022 AN - OPUS4-55196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tabaka, Weronika A1 - Schartel, Bernhard T1 - Less is More: Optimised Fire Performance in Glass Fibre-reinforced Polybutylene Terephthalate Laminates with Concentrated Flame Retardant Top Layer N2 - To achieve optimum fire performance while maintaining mechanical integrity, flame retardants (FR) were strategically concentrated in the surface layer of a two-layer glass fibre-reinforced polybutylene terephthalate (PBT) laminate structure. Three potentially synergistic FR systems were selected to improve the fire performance of glass fibre-reinforced PBT: boehmite (AlOOH) with melamine polyzinc phosphate (MPZnP), aluminium diethyl phosphinates (AlPi) with melamine cyanurate (MC), and expandable graphite (EG) with melamine polyphosphate (MPP). Limited Oxygen Index (LOI) and UL-94 testing highlighted the influence of laminate architecture on flammability. The cone calorimeter results showed that increasing the FR concentration in the top layer significantly reduced both the peak heat release rate (PHRR) and the maximum average rate of heat emission (MARHE), with improvements depending on the specific FR system used. The laminate L-PBT/GF/AlOOH/MPZnP with a 2:2 thickness ratio showed outstanding performance, achieving a 45 % reduction in MARHE compared to composites with uniform FR distribution. This result showcases the superior thermal barrier properties and synergistic behaviour of AlOOH and MPZnP. The fire performance of laminates containing AlPi and MC was strongly influenced by the distribution and concentration of AlPi/MC. The EG/MPP system was found to be highly effective, forming a protective intumescent layer that significantly reduced both HRR and MARHE, demonstrating the effectiveness of strategically concentrating FR in the top layer. KW - Glass fibres KW - PBT KW - Flame retardants KW - Composites KW - Laminates KW - Fire behaviour KW - Flammability PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626381 DO - https://doi.org/10.1016/j.jcomc.2025.100577 SN - 2666-6820 VL - 16 SP - 1 EP - 15 PB - Elsevier CY - Amsterdam AN - OPUS4-62638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tabaka, Weronika T1 - Bench-scale fire stability testing of carbon fibre reinforced polymer laminates with protective layers N2 - Fire resistance testing of components made of carbon fibre reinforced polymers (CFRP) composites usually demands intermediate-scale or full-scale testing. In this study, a bench-scale test is presented as a practicable and efficient method to assess the improvement in structural integrity of CFRP with different protective interlayers during fire. Fire stability is one of the biggest issues of carbon fibre reinforced polymer (CFRP) composites, particularly when they are using in load bearing applications. As soon as the glass transition temperature of polymer matrix (100-200°C) is achieved, the composite loses its structural integrity, what leads to the distortion and failure. The principal fire stability test is based on simultaneous application of fire and mechanical load. Since the carbon fibres can transfer the tensile loads quite well, the compression load is chosen as a required mechanical load for a test. The fire tests were preceded by a static load test at room temperature to determine ultimate failure load. The specimen was loaded with a compression force until the failure load was reached, which was observed as a buckling. For the fire tests, 10% of compression failure load and direct flame of a fully developed fire (heat flux ≈ 180 kW m-2) were applied simultaneously to the specimen, while the time to failure was measured. The possibilities of bench-scale fire stability testing were presented by investigating new types of laminate structures, which exhibit promising flame retardancy and fireproof properties. The new approach of CFRP laminate differs with a protective concept. Every system consists of two different interlayers (titanium foil, thermoplastic foil PEI, ceramic layer WHIPOX, rubber tape Pyrostat, basalt fibres and kenaf fibres), where the one layer constitutes the fireproof protection, that delays the rise of temperature in the rest of laminate, and the second layer provides very good structural connection with carbon fibre layers, thus improves the mechanical integrity of CFRP composite in fire. The time to failure of CFRP composite was 17s. Protective systems significantly enhance the fire stability and increased time to failure by 3 to 10 times. Thicker specimens showed longer resistance time, however CFRP laminate with ceramic layer and titanium foil presented outstanding results and the best performance. The protection with Kenaf and basalt fibres offered a natural fibre solution with also good fire resistance performance Although bench-scale tests are limited with respect to assessing the performance of components and structures, they are valuable in the assessment of different materials concepts. Furthermore, the reduced effort of conducting bench-scale test (lower costs, time, personnel resources) makes it more practical and effective. T2 - 19th European meeting on Fire Retardant Polymeric Materials (FRPM23) CY - Dübendorf, Switzerland DA - 26.06.2023 KW - Fire resistance KW - Carbon fibre reinforced polymer KW - Bench-scale testing PY - 2023 AN - OPUS4-57880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - An, Q. A1 - Bäßler, Ralph A1 - Hertwig, Andreas A1 - Rehfeldt, Rainer A1 - Hidde, Gundula T1 - Investigation of mechanical stress and B10 exposure on FKM polymer N2 - Biofuels, particularly biodiesel, have gained significant attention as an alternative to traditional fossil fuels in recent years. Unlike diesel, which contains hundreds of compounds, biodiesel only contains a few compounds in the C16-C18 carbon chain. However, the use of biodiesel in automobile and transportation applications can result in problems of degradation or even damage in materials. Among the commonly used polymer materials, fluorocarbon (FKM) shows excellent performance and high stability and compatibility towards oil, diesel, ethanol, and other chemicals. FKM is a family of fluorocarbon-based fluoroelastomer materials, which provide excellent high-temperature and chemical stability compared to other elastomers. As a result, FKM is widely used in chemical processes such as petroleum refining, where it is used for sealings, pumps, and other components. T2 - TMS 2024 153rd Annual Meeting & Exhibition Supplemental Proceedings CY - Orlando, Florida, USA DA - 03.03.2024 KW - B10 exposure KW - FKM polymer PY - 2024 AN - OPUS4-59636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan T1 - Comparative study on standardized ignition sources used for explosion testing N2 - For the determination of safety characteristics of gases, vapors and dusts different types of ignition sources are used in international standards and guidelines. Table 1 compares technical relevant ignition sources with their main features. The paper presents test results of a comparative calorimetric and visual study between four different types of ignition sources. The ignition procedures were analyzed visually with a high-speed camera and electric recordings. In addition to that, the influence of the electrode-orientation, -distance as well as ignition energy on the reproducibility of the exploding wire igniter was tested. The exploding wire is already in use for standardized determination of safety characteristics of gases, first tests on the suitability of the exploding wire igniter for dust testing have been carried out by Scheid et al. Using the exploding wire, the ignition energy can be varied from 2 to 10 000 J (2 x 5 000 J) and thus it could be used for gases, vapors, dusts and hybrid mixtures. Moreover it can be used at high initial pressures and it is the only ignition source with an easily measurable ignition energy release. Furthermore, it does not introduce another chemical reaction into the system. Finally, a proposal for a standard ignition source for explosion tests on hybrid mixtures is derived from the test results. T2 - 13th International Symposium on Hazards, Prevention and Mitigation of Industrial Explosions CY - Braunschweig, Germany DA - 27.07.2020 KW - Ignition source KW - Exploding Wire KW - Safety characteristics determination KW - Hybrid mixtures PY - 2020 AN - OPUS4-51691 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan T1 - Entwicklungen zu Bestimmungsverfahren für sicherheitstechnische Kenngrößen des Explosionsschutzes für hybride Gemische N2 - Zur Bestimmung sicherheitstechnischer Kenngrößen (STK) von hybriden Gemischen (Gemisch aus mindestens zwei brennbaren Phasen, wie z.B. Staub/Gas- oder Gas/Dampf-Gemisch) existieren bislang keine einheitlichen, genormten Prüfmethoden. Die Normen und Regelwerke zur Bestimmung der STK von einphasigen brennbaren Systemen (Staub, Gas, Dampf) unterscheiden sich teilweise erheblich. Beispielsweise sind in den jeweiligen Normen für Stäube, Gase und Dämpfe unterschiedliche Zündquellen und Zündenergien definiert. Des Weiteren unterscheiden sich die in den Normen definierten Prüfabläufe bei der Gemischherstellung. Bei der Entwicklung einer einheitlichen Norm für hybride Gemische muss der Einfluss dieser beiden Parameter ermittelt werden, um die Vergleichbarkeit mit den STK der einzelnen Komponenten Gas, Staub und Dampf gewährleisten zu können und bisherige Erkenntnisse zu hybriden Gemischen interpretieren und bewerten zu können. T2 - VDI-Fachtagung "Sichere Handhabung brennbarer Stäube" CY - Online meeting DA - 04.11.2020 KW - Hybride Gemische KW - Explodierender Draht KW - Sicherheitstechnische Kenngrößen KW - Zündquellen PY - 2020 AN - OPUS4-51692 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klippel, Andrea A1 - Hofmann‐Böllinghaus, Anja A1 - Piechnik, Kira A1 - Heydick, Lukas A1 - Wu, Hongyi A1 - Köhler, Florian A1 - Klaffke, Benjamin T1 - Experimental Analysis of Fire Behavior in Pine Forests and Agricultural Fields: Large‐Scale Tests Conducted Within the European TREEADS Project N2 - Two large‐scale experiments investigated fire spread mechanisms in vegetation ground fires in a pine forest and an agricultural field within the European TREEADS project. The tests, conducted in Saxony‐Anhalt and Brandenburg, targeted regions with dry, sandy soils and extensive pine stands and aim to improve suppression strategies and wildfire research. The forest experiment was conducted on a 16 × 22 m plot with line ignition using a gasoline‐diesel mix. Fire spread was documented with drone‐based video and infrared imaging. Ninety‐six thermocouples and two gas sensors were mounted on trees, and a mobile FTIR spectrometer enabled real‐time smoke analysis. A tilled and foam‐treated strip prevented uncontrolled spread. Under stable weather conditions (23°C, light wind, low soil moisture), a consistent temperature rise and distinct combustion phases were observed. Smoldering dominated in areas with mosses, grasses, and deadwood, with intermittent flaming, limited flame heights (< 0.5 m), and substantial smoke production. Peak temperatures exceeded 500°C, and CO concentrations reached 238 ppm, though wind turbulence complicated gas sampling. The second experiment on a cut agricultural field near Nauen involved burning approximately 700 m2 using a 20 m ignition line aligned with wind direction. Drone‐based infrared monitoring captured rapid spread on the stubble surface. The results underscore the variability and measurement challenges of outdoor fires and highlight the necessity of continued large‐scale experiments to support physical and numerical wildfire modeling. These findings provide essential empirical data for evaluating vegetation‐specific burning behavior, improving sensor deployment strategies, and refining validation approaches for next‐generation wildfire spread models under central European fuel and weather conditions, and supporting decision‐making in wildfire management. KW - Wildfire KW - Pine KW - Crop PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654199 DO - https://doi.org/10.1002/fam.70045 SN - 0308-0501 SP - 1 EP - 11 PB - Wiley AN - OPUS4-65419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hahn, Sarah‐K. A1 - Gnutzmann, Tanja A1 - Meinert, Marion A1 - Hofmann-Böllinghaus, Anja A1 - Oberhagemann, Dirk A1 - Krause, Ulrich T1 - Incipient Fires—Definition, Detection and Extinguishment by Laypersons N2 - The earlier a fire is noticed, the less developed it is and the easier it can be prevented respectively stopped, even by laypersons. Within the research project ‘TEBRAS’ the incipient phase of fires was investigated in detail. In the course of the project, it became apparent that the definition of what exactly the incipient phase of a fire encompasses is not definite and depends on the disciplines dealing with the subject ‘fire’. Based on the results of a literature review, an inquiry under experts and laypersons as well as practical fire tests a definition for the phenomenon of the incipient fire was developed which divides it into four phases. Driving key factors for each phase are identified considering the main parameters to detect and extinguish the fire. KW - Developing fires KW - Development of fires PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-649310 DO - https://doi.org/10.1002/fam.70025 SN - 0308-0501 VL - 50 IS - 1 SP - 3 EP - 10 PB - Wiley AN - OPUS4-64931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -