TY - CONF A1 - Eberwein, Robert T1 - Wasserstoff - Kryogene Anwendungen N2 - Wasserstoff wird als ein potenzieller alternativer Energieträger gesehen, mit dem die für 2050 gesetzten Klimaziele erreicht werden könnten. Der Transport von Wasserstoff ist mittels verschiedener Speichertechniken möglich, von denen der kryogene Transport mit den größten volumetrischen Energiedichten einhergeht. Hierdurch eignen sich diese Speicher besonders für die energieintensiven Verkehrsmittel im Land-, See- und Flugverkehr. Im Vortrag werden Speichertechniken, Gefahren im Umgang mit kryogenen Gasen sowie bisherige Störfälle dargestellt. Darauf aufbauend wird ein Teil der aktuellen Forschungsarbeit an der BAM vorgestellt, die die Sicherheit dieser Speicher unter außergewöhnlichen Belastungen adressiert. T2 - 26. Gefahrgutkongress Mecklenburg-Vorpommern CY - Rostock, Germany DA - 03.11.2022 KW - Wasserstoff KW - H2 KW - LNG KW - LH2 KW - Tank PY - 2022 AN - OPUS4-56181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Johann, Sergej A1 - Baensch, Franziska A1 - Sturm, Patrick A1 - Tiebe, Carlo A1 - Pötschke, Samuel A1 - Lay, Vera ED - Holl, H. T1 - HF RFID-based measurement comparison for method optimization in M2 concrete and alkali-activated mortars N2 - Monitoring of repositories for radioactive waste requires techniques which can be applied long-term under harsh conditions. In this work, the reliability and suitability of materials and a capacitive sensor for measuring relative humidity are investigated, which are to be embedded in the special concrete components for the closure structures of underground repository. Preliminary tests with accelerated aging of the materials used, validation of the sensors under difficult conditions, investigations of the surfaces after aging by pH 14 solution, defined exposure of the sensors in a climatic chamber and the microscope images are discussed. The results will be used for further development and optimization of the RFID based sensor systems which can be applied to monitor the condition of different building structures without cabling. T2 - 37th Danubia - Adria Symposium on Advances in Experimental Mechanics CY - Linz, Austria DA - 21.09.2021 KW - Alkali-activated mortars KW - Passive sensor interface KW - RFID KW - Structural health monitoring KW - Smart structures PY - 2022 DO - https://doi.org/10.1016/j.matpr.2022.03.465 SN - 2214-7853 VL - 62 IS - 5 SP - 2571 EP - 2576 PB - Elsevier CY - Amsterdam AN - OPUS4-54697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Priebe, Nsesheye Susan T1 - Influence of calcination conditions and varying compositions on the reactivity and performance of brick clays as supplementary cementitious materials T1 - Der Einfluss von Kalzinierungsbedingungen und verschiedenen Zusammensetzungen auf die Reaktivität und Eigenschaften von Ziegeltonen verwendet als Zusatzstoffe in Beton N2 - Calcined clays as supplementary cementitious materials (SCMs) have been identified and credited to be a viable solution in mitigating the CO2 emissions related to cement production and consumption. Calcined clays range from a variety of different clay types based on an assortment of varying minerals and compositions. While extensive data is available on kaolinitic clays (based on the 1:1 clay type), other clays such as brick clays (based on the 2:1 clay type) are currently understudied, although such clays are largely more available than the kaolinitic clays. The aim of this thesis is to draw attention to the varying compositions present in two selected brick clays in Germany and elaborate on how such compositions affect their suitability to be used as SCMs in blended cement systems. The novelty of this thesis explains the relationship between the reactivity of the bricks to their varying compositions and their suitability for their employment as SCMs. This was based on their chemical and physical transformations in the calcination temperature range 650–900 or 950 °C, and the performance of the calcined brick clays in blended cement systems measured by their heat evolution, strength development and durability-related properties. The results of their performance were compared to two kaolinitic clays with varying compositions. While the kaolinitic clays generally exhibited the best performance as SCMs, the brick clay with a lower Fe2O3 content showed promising results similar to the kaolinitic clays when an optimum calcination temperature is applied and when substituted at a moderate cement substitution rate. Thus, this finding promoted further efforts made to improve the reactivity of the brick clay by producing a mixed clay composed of 50 % brick clay (with lower Fe2O3 content) and 50 % kaolinitic clay. The mixed clay was compared to the two individual brick clays and one kaolinitic clay, whereby optimum calcination conditions were performed in large-scale simulating an industrial-scale production of SCMs. All calcined clays exhibited pozzolanic reactivity, with the performance of the brick clays inferior to the kaolinitic clay, however, the mixed clay performed very similar to the kaolinitic clay. At a similar degree of hydration compared to plain Portland cement, the good performance of the mixed clays was especially evident in the strength development and improved chloride penetration resistance, which was caused by a refinement in the pore structure in the cementitious systems. Moreover, it was deduced that not only the high surface area, but also, the solubility of Si and Al ions in the resulting calcinate of the mixed clays plays a significant role when calcined at ~600–700 °C, which points to viable options for optimal employment of brick clays in cementitious systems. N2 - Die bei der Zementproduktion freigesetzte CO2-Menge und die daraus resultierenden Folgen für das Klima machen die Entwicklung von Zementersatzstoffen mit geringerem CO2-Fußabdruck erforderlich. Als besonders vielversprechend haben sich dabei die kalzinierten Tone erwiesen. Bei diesen handelt es sich um komplexe Systeme, bestehend aus einer Vielzahl verschiedener Tonminerale in variierender Konzentration und Zusammensetzung. Während für kaolinitische Tone (basierend auf 1:1 Tonmineralarten) bereits umfangreiche Daten gesammelt werden konnten, ist der Kenntnisstand zu anderen Tonarten z.B. Ziegeltonen (basierend auf 2:1 Tonmineralarten) derzeit noch unzureichend. Besonders vor dem Hintergrund der erheblich größeren Verfügbarkeit dieser Tonarten stellt dies einen erheblichen Nachteil dar. Ziel dieser Arbeit ist es, anhand zweier Ziegeltone aus Deutschland, aufzuzeigen welche Auswirkung die unterschiedliche Zusammensetzung der Tone sowohl auf die Reaktivität als auch auf den Einsatz als Zementersatzstoffen in Mischzementsystemen hat. Entsprechende Änderungen in der Zusammensetzung der kalzinierten Tone wurden durch die Variation der Kalzinierungstemperatur im Temperaturbereich zwischen 650 °C und 900 °C bzw. 950 °C und den folglich unterschiedlich ablaufenden chemischen und physikalischen Umwandlungsprozessen der Tonminerale erreicht. Die Leistungsfähigkeit dieser Systeme wurde anhand der Wärme- und Festigkeitsentwicklung sowie den Dauerhaftigkeitseigenschaften bewertet. Als Referenzsysteme dienten zwei 1:1 Tone mit unterschiedlicher Zusammensetzung. Die bei den 1:1 Tonen erzielten Reaktivitäten waren im Vergleich zu den Ziegeltonen zwar höher, aber bei entsprechender Kalzinierungstemperatur und moderater Zementersatzrate konnten auch bei den Ziegeltonen vielversprechende Ergebnisse erzielt werden. Basierend auf diesen Ergebnissen wurden in einem weiteren Schritt Mischtone, bestehend aus kaolinitischem Ton und Ziegelton mit geringerem Fe2O3 Gehalt (50:50), untersucht. Zur Bewertung wurden die zuvor untersuchten Ziegeltone und ein 1:1 Ton herangezogen. Bei allen kalzinierten Tonen konnte die pozzolanische Reaktion nachgewiesen werden, wobei der Ziegelton die geringsten und die 1:1 Tone die höchsten Werte lieferte. Das Mischtonsysteme sind leistungstechnisch bei den 1:1 Tonen einzuordnen. Die strukturverfeinernde Wirkung des Mischtons beim Einsatz als Zementersatz in Portlandzementsystemen führte sowohl bei der Festigkeitsentwicklung als auch beim Chlorideindringwiderstand zu einer Leistungssteigerung. Zudem konnte gezeigt werden, dass nicht nur die große spezifische Oberfläche, sondern auch die hohe Löslichkeit der Si- und Al-Ionen in den Kalzinaten der bei ~600-700 °C kalzinierten Mischtone einen großen Einfluss hat und den Einsatz der Ziegeltone in zementären Systemen begünstigt. Die Möglichkeit zur Herstellung von Zementersatzstoffen im industriellen Maßstab konnte durch Versuche im Großmaßstab ebenfalls nachgewiesen werden. KW - Blended cement KW - Brick clay KW - Calcined clay KW - Hydration KW - Illite KW - Kalzinierte Tone KW - Ziegelton PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:co1-opus4-58816 DO - https://doi.org/10.26127/BTUOpen-5881 SP - i EP - 153 PB - Brandenburgische Technische Universität Cottbus-Senftenberg CY - Cottbus AN - OPUS4-55048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Eilers, M. A1 - Alte-Teigeler, R. A1 - Borchers, R. A1 - Gallai, G. A1 - Habiger, D. A1 - Recknagel, Christoph A1 - Karczewski, B. A1 - Koll, J. A1 - Lorenz, S. A1 - Marossow, H. A1 - Schneider, Th. A1 - Seiffart, J. A1 - Stark, S. A1 - et al., T1 - Zusätzliche Technische Vertragsbedingungen und Richtlinien für Ingenieurbauten, Teil 6: Bauwerksausstattung, Abschnitt 7: Fahrbahnübergänge N2 - Die Zusätzlichen Technischen Vertragsbedingungen und Richtlinien für Ingenieurbauten (ZTV-ING) wurden zuletzt mit ARS Nr. 23/2021 vom 20. 10. 2021 mit dem Stand 2021/10 fortgeschrieben. Die jetzige Fortschreibung beinhaltet eine Gliederungsänderung des Regelwerks, um die für den Brückenbau relevanten Teile vorne gebündelt darstellen zu können. Eine Synopse hierzu ist der Anlage 4 zu entnehmen. „Wesentliche Änderungen in den ZTV-ING“ gegenüber der letzten Fassung sind der Anlage 3 zu entnehmen. In gleicher Weise sind die aktuellen „Hinweise zu den ZTV-ING — Stand 2022/01“ gemäß Anlage 2 einzubeziehen. Die Hinweise zu den entsprechenden Abschnitten der ZTV-ING sind bei der Projektbearbeitung und Ausschreibung zu beachten. Soweit die „Hinweise zu den ZTV-ING“ für die jeweilige Maßnahme zutreffend sind und vertragsrechtliche Bedeutung haben, sind entsprechende Textpassagen gesondert in die Vergabeunterlagen aufzunehmen bzw. zu vereinbaren. KW - Brückenbeläge KW - Asphaltbauweisen KW - Fahrbahnübergänge PY - 2022 SN - 978-3-86446-344-0 VL - 782/7 SP - 1 EP - 30 PB - FGSV Verlag GmbH CY - Köln AN - OPUS4-56219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Jankuj, V. A1 - Krietsch, Arne T1 - Comparative Study on Standardized Ignition Sources Part 2: Exploration of the Initial Igniting Volume of Standardized Ignition Sources for the Determination of Explosion Characteristics N2 - There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible. While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique-. T2 - Loss Prevention CY - Prag, Czechia DA - 06.06.2022 KW - Ignition source KW - Hybrid Mixtures KW - 20L-sphere PY - 2022 DO - https://doi.org/10.3303/CET2290087 SN - 2283-9216 VL - 2022 IS - 90 SP - 517 EP - 522 PB - AIDIC CY - Milano AN - OPUS4-55028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Benke, Alexander A1 - Cloney, C. A1 - D’Hyon, S. A1 - Dufaud, O. A1 - Dyduch, Z. A1 - Gabel, D. A1 - Geoerg, P. A1 - Heilmann, V. A1 - Jankuj, V. A1 - Jian, W. A1 - Krause, U. A1 - Krietsch, Arne A1 - Mynarz, M. A1 - Norman, F. A1 - Skrinsky, J. A1 - Taveau, J. A1 - Vignes, A. A1 - Zakel, S. A1 - Zhong, S. T1 - 1st international round robin test on safety characteristics of hybrid mixtures N2 - There is no applicable existing standard for the determination of safety characteristics for hybrid mixtures. While developing a new standard in a joint research project in Germany first results from parameter studies led to a standard procedure that can be adopted by laboratories that are already testing dusts in the so called 20L-sphere with as little additional effort as necessary. In fact, one of the main objectives of this research project was to keep modifications and adjustments from the generally accepted dust testing procedures as easy and minimal as possible so as to limit potential deviations from one laboratory to another. In this first round robin test on hybrid mixtures ever, with methane as gas component and a specific corn starch as dust sample, the practicality of the whole procedure, the scattering of the results and the deviation between the testing apparatuses is investigated. This paper summarizes the experimental procedure adopted and objectives of the first round-robin phase involving three of the four original German companies, plus volunteering laboratories from Australia, Belgium, Czech Republic, France, Poland and P.R. China. The results will have an impact on the new standard and may lead to robust data for later simulation purposes. KW - Hybrid mixtures KW - 20L-sphere KW - Round robin test KW - Turbulent combustion PY - 2022 DO - https://doi.org/10.1016/j.jlp.2022.104947 SN - 0950-4230 VL - 81 SP - 1 EP - 8 PB - Elsevier CY - Amsterdam AN - OPUS4-56516 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jankuj, V. A1 - Mynarz, M. A1 - Krietsch, Arne A1 - Spitzer, Stefan A1 - Leipik, P. T1 - Experimental investigation of the consequences of acetylene pressure cylinder failure under fire conditions N2 - Acetylene pressure cylinders are widely used in the industrial sector for welding, flame cutting, or heating. Sometimes during work, not only with acetylene cylinders, fires occur and in this case the risk of destruction increases and the behavior of such an exposed cylinder is unpredictable. The purpose of this study is to identify those critical conditions when acetylene cylinders burst and explode in fires. In the present study, acetylene cylinders were exposed to fire conditions. For this purpose, a woodpile as a source of fire was chosen, tested, and evaluated. In addition to the fire condition, this option guaranteed reproducibility and similar conditions for all tests. The individual cylinders were equipped with thermocouples measuring the shell temperature, and half of them were prepared in order to measure the temperatures inside the cylinder. An important factor was the measurement of the amount of pressure that was achieved during the destruction of the cylinder. For this purpose, a pressure transducer was attached to the outlet of the cylinder valve. Exposed to direct fire, they can explode in 10 min, which was confirmed. The critical pressure of 40 bar has been reached in 6 min, followed by destruction after 7 min in fire. Cylinders with internal thermocouples were destroyed when lower pressure was achieved. This confirms the fact that any change of the pressure cylinder affects the original properties. After the tests, the fragments of the selected cylinders were subjected to material tests. The results obtained in these tests are the main source of information for understanding the behavior of acetylene cylinders in fire and the possibility of increasing the safety of intervening rescue services in an emergency. KW - Acetylene KW - Pressure Cylinders KW - Fire KW - Explosion KW - Fireball PY - 2022 DO - https://doi.org/10.1016/j.jlp.2022.104874 VL - 80 SP - 1 EP - 12 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-55755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Spitzer, Stefan A1 - Askar, Enis A1 - Hecht, Kristin A1 - Gabel, D. A1 - Zakel, S. A1 - Krietsch, Arne T1 - Requirements for a Hybrid Dust-Gas-Standard: Influence of the Mixing Procedure on Safety Characteristics of Hybrid Mixtures N2 - While developing a standard for the determination of safety characteristics for hybrid mixtures the authors discovered, that, beside the ignition source, the mixing procedure is the main difference between the single-phase standards for dusts and gases. The preparation of hybrid mixtures containing a flammable gas and a flammable dust in the 20 L-sphere can be realized in different ways. Either the flammable gas is filled only in the sphere or only in the dust container or in both. In previous works, almost always the first method is applied, without giving any information on the accuracy of the gas mixtures. In this work the accuracy of the gas mixtures and the results of the tests applying two methods of mixing were studied. No significant influence of the mixing method itself on the safety characteristics explosion pressure pex and the normalized rate of pressure rise (K-value) was found. Obviously, homogenization of the gas mixtures can be obtained sufficiently by the turbulence that is caused during the injection from the dust container into the explosion chamber within a short time. However, the mixing procedure has a great influence on the accuracy of the gas amount of the mixtures obtained. Without modifying the 20 L-sphere by installing precise pressure sensors, assuring its tightness and performing gas analysis, it must be expected, that the accuracy of the gas mixtures is very low. This has a significant influence on the measured safety characteristics and may lead to unsafe facilities or unnecessary expensive safety measures. KW - Hybrid mixtures KW - 20 L-sphere KW - Pre-ignition pressure rise KW - Post-injection pressure drop KW - Safety characteristics PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-554610 DO - https://doi.org/10.3390/fire5040113 VL - 5 IS - 4 SP - 1 EP - 10 PB - MDPI CY - Basel AN - OPUS4-55461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan T1 - Comparative Study on Standardized Ignition Sources Part 2: Exploration of the Initial Igniting Volume of Standardized Ignition Sources for the Determination of Explosion Characteristics N2 - There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible. While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique. T2 - Loss Prevention CY - Prague, Czech Republic DA - 06.06.2022 KW - Ignition source KW - Hybrid Mixtures KW - 20L-sphere PY - 2022 AN - OPUS4-55029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kazlagić, Anera A1 - Russo, Francesco A1 - Vogl, Jochen A1 - Sturm, Patrick A1 - Stephan, D. A1 - Gluth, Gregor ED - Resch-Genger, Ute ED - Koch, Matthias ED - Meermann, Björn ED - Weller, Michael G. T1 - Development of a sample preparation procedure for Sr isotope analysis of Portland cements N2 - The 87Sr/86Sr isotope ratio can, in principle, be used for provenancing of cement. However, while commercial cements consist of multiple components, no detailed investigation into their individual 87Sr/86Sr isotope ratios or their influence on the integral 87Sr/86Sr isotope ratio of the resulting cement was conducted previously. Therefore, the present study aimed at determining and comparing the conventional 87Sr/86Sr isotope ratios of a diverse set of Portland cements and their corresponding Portland clinkers, the major component of these cements. Two approaches to remove the additives from the cements, i.e. to measure the conventional 87Sr/86Sr isotopic fingerprint of the clinker only, were tested, namely, treatment with a potassium hydroxide/sucrose solution and sieving on a 11-µm sieve. Dissolution in concentrated hydrochloric acid/nitric acid and in diluted nitric acid was employed to determine the 87Sr/86Sr isotope ratios of the cements and the individual clinkers. The aim was to find the most appropriate sample preparation procedure for cement provenancing, and the selection was realised by comparing the 87Sr/86Sr isotope ratios of differently treated cements with those of the corresponding clinkers. None of the methods to separate the clinkers from the cements proved to be satisfactory. However, it was found that the 87Sr/86Sr isotope ratios of clinker and cement generally corresponded, meaning that the latter can be used as a proxy for the clinker 87Sr/86Sr isotope ratio. Finally, the concentrated hydrochloric acid/nitric acid dissolution method was found to be the most suitable sample preparation method for the cements; it is thus recommended for 87Sr/86Sr isotope analyses for cement provenancing. KW - Cement KW - Provenancing KW - Sr isotopes KW - Portland clinker KW - Dissolution PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-542239 DO - https://doi.org/10.1007/s00216-021-03821-7 SN - 1618-2642 SN - 1618-2650 VL - 414 IS - 15 (Topical collection: Analytical methods and applications in the materials and life sciences) SP - 4379 EP - 4389 PB - Springer CY - Berlin AN - OPUS4-54223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. T1 - Capabilities of using mobile platforms for monitoring hazard scenarios by the example of the RASEM project N2 - This presentation shows the capabilities of mobile platforms for monitoring hazard scenarios. As an example the RASEM project is presented. Furthermore two ideas for future work are shown, namely, Aerial-based Gas Tomography and Passive Smart Dust. T2 - Climate Change @ Fire Science Workshop CY - Berlin, Germany DA - 10.11.2022 KW - RASEM KW - Dust sensor KW - Low-cost KW - Sensor network KW - Passive Smart Dust KW - Gas Tomography PY - 2022 AN - OPUS4-56296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -