TY - CONF A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Epple, Niklas A1 - Liao, Chun-Man T1 - Recent advances in (ultra)sonic active and passive monitoring of reinforced and prestressed concrete structures N2 - In addition to already established structural monitoring methods such as deformation, inclination or strain gauges or acoustic emission sensors, sonic or ultrasonic monitoring might provide valuable information about the condition or alteration of a structure. Sensors such as geophones, recording ambient noise in the sonic and subsonic frequency range can provide information beyond modal analysis by using interferometric methods. Wave velocities determined by this method are related to the elastic properties and stiffness of material and structure and can be converted into damage indicators. Embedded active ultrasonic transducer networks can provide more detailed insight about deterioration or damages again, using interferometric technologies. This approach is extremely sensible, detecting relative change in velocity on down to 10-5. These methods, including benefits and remaining challenges, are demonstrated using data from a test structure at BAM’s test site demonstrating the case of prestress loss, and data from an actual bridge still under traffic. T2 - International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Monitoring KW - Ultrasonic KW - Non-destructive testing KW - Coda wave KW - Bridge PY - 2022 AN - OPUS4-56000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Bio, Waste, Non-vegan – Fun, Food for Thought, or Future N2 - Overview of the state of the art and current trends with the main topics: - renewable sources in flame retardant polymers (flame retarded bio-polymers and biocomposites; bio-flame retardants, renewable adjuvants from industrial waste) - flame retardancy meets sustainability - concepts between analogy and out-of-the-box. T2 - 18th SKZ International Conference on Trends in Fire Safety and InnovativeRFlame retardants for Plastics CY - Würzburg/Rottendorf, Germany DA - 27.09.2022 KW - Bio-polymer KW - Bio-composite KW - Renewable source KW - Renewable adjuvants KW - Vitrimer KW - Bio-flame retardant PY - 2022 AN - OPUS4-55840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel T1 - Wehrmedizinisches Sonderforschungsvorhaben 29K4 "Primäres Explosionstrauma": „Entwicklung und Validierung eines Körpermodells und eines Stoßwellengenerators zur Simulation der intrakorporalen Stoßwellenausbreitung nach Explosionen“ N2 - Im Rahmen dieses Vortrags wurden aktuelle Arbeiten im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. T2 - 8. KSK Symposium Rüstung 2022 CY - Altensteig/Wart, Germany DA - 13.09.2022 KW - Blast KW - Primäres Explosionstrauma KW - Einsatzkräfte KW - Polizei KW - Körpermodell PY - 2022 AN - OPUS4-55841 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Bewertung von Fallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen N2 - Bericht über die Vorgehensweise der systematischen Untersuchungen zur Entwicklung angepasster Kriterien für die Bewertung von Aufprallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen T2 - AK Prüfstellen CY - Berlin, Germany DA - 21.09.2022 KW - Fallprüfung KW - Aufprallfundament KW - Gefahrgutverpackung KW - Fallfundament KW - Mechanische Sicherheitsprüfung PY - 2022 AN - OPUS4-55842 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Bewertung von Fallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen N2 - Bericht über die Vorgehensweise der systematischen Untersuchungen zur Entwicklung angepasster Kriterien für die Bewertung von Aufprallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen T2 - ERFA Verpackungen CY - Berlin, Germany DA - 22.09.2022 KW - Fallprüfung KW - Aufprallfundament KW - Gefahrgutverpackung KW - Fallfundament KW - Mchanische Sicherheitsprüfung PY - 2022 AN - OPUS4-55843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Johann, Sergej A1 - Kadoke, Daniel A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Zehn, M. W. T1 - Damage assessment of complete, filled fibreboard boxes in regulative vertical impact tests by dropping N2 - Due to the high damping mechanical properties of fibreboard materials, corrugated fibreboard boxes are widely used as transport packages of dangerous goods. Since there is a hazard of vertical impact within the distribution system, drop tests are performed as design type tests to assess the package’s ability to withstand damage. However, there is little information in this context regarding the mechanical response of a filled fibreboard box. This work aims to propose a concept utilizing experimental drop test results by means of finite-element (FE) analyses in order to predict the damage resistance of complete, filled corrugated fibreboard boxes which are ready for transportation. T2 - 38th Danubia Adria Symposium on Advances in Experimental Mechanics CY - Poros Island, Greece DA - 20.09.2022 KW - Drop test KW - Dangerous goods packagings KW - Corrugated fibreboard box KW - Finite-element-analysis KW - Explicit transient simulation KW - Crash simulation PY - 2022 AN - OPUS4-55845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Grengg, C. A1 - Ukrainczyk, N. A1 - Mittermayr, F. A1 - Dietzel, M. T1 - Acid resistance of alkali-activated materials: Recent advances and research needs N2 - Cementitious materials are frequently applied in environments in which they are exposed to acid attack, e.g., in sewer systems, biogas plants, and agricultural/food-related industries. Alkali-activated materials (AAMs) have repeatedly been shown to exhibit a remarkably high resistance against attack by organic and inorganic acids and, thus, are promising candidates for the construction and the repair of acid-exposed structures. However, the reaction mechanisms and processes affecting the acid resistance of AAMs have just recently begun to be understood in more detail. The present contribution synthesises these advances and outlines potentially fruitful avenues of research. The interaction between AAMs and acids proceeds in a multistep process wherein different aspects of deterioration extend to different depths, complicating the overall determination of acid resistance. Partly due to this indistinct definition of the ‘depth of corrosion’, the effects of the composition of AAMs on their acid resistance cannot be unambiguously identified to date. Important parallels exist between the deterioration of low-Ca AAMs and the weathering/corrosion of minerals and glasses (dissolution-reprecipitation mechanism). Additional research requirements relate to the deterioration mechanism of high-Ca AAMs; how the character of the corroded layer influences the rate of deterioration; the effects of shrinkage and the bond between AAMs and substrates. KW - Alkali-activated materials KW - Acid attack KW - Acid resistance KW - Concrete repair KW - MIC PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557376 DO - https://doi.org/10.21809/rilemtechlett.2022.157 SN - 2518-0231 VL - 7 SP - 58 EP - 67 PB - RILEM Publications SARL CY - Paris AN - OPUS4-55737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grunert, Wiebke A1 - Walter, Astrid A1 - Schwarz, Silke T1 - Forschung zur zivilen Sicherheit: Homemade Explosives besser erkennen und Anschläge verhindern N2 - Terroranschläge stellen nach wie vor eine stete Bedrohung für Gesellschaften weltweit dar. Häufig bedienen sich Terroristen*innen dabei selbsthergestellter Explosivstoffe, auch als homemade explosives (HMEs) bezeichnet, die aus alltäglichen Chemikalien in improvisierten Laboratorien hergestellt werden. Anleitungen für die Herstellung solcher Explosivstoffe werden im Internet geteilt und setzen meist kein oder nur ein rudimentäres Verständnis der Chemie voraus. Um geplante Terroranschläge schon während der Phase der Herstellung zu vereiteln, werden Methoden entwickelt, die frühzeitig Hinweise auf solche Aktivitäten geben. In dem EU-geförderten Projekt ODYSSEUS wird in enger Zusammenarbeit zwischen Behörden und Organisationen mit Sicherheitsaufgaben (BOS) sowie Partnern aus Industrie und Forschung an der Entwicklung neuer Methoden zur Erkennung von HMEs und ihrer Ausgangsstoffe gearbeitet. KW - Terroranschläge KW - EU Projekt ODYSSEUS KW - HMEs PY - 2022 DO - https://doi.org/10.37307/j.2199-7349.2022.09 SN - 2199-7349 VL - 2022 IS - 09 SP - 391 EP - 361 PB - Erich Schmidt Verlag CY - Berlin AN - OPUS4-55747 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jauregui-Correa, J. C. A1 - Morales-Velazquez, L. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. T1 - Method for predicting dynamic loads for a health monitoring system for subway tracks N2 - This paper presents a method for processing acceleration data registered on a train and determining the health condition of a subway’s substructure. The acceleration data was converted into a dynamic deformation by applying a transfer function defined using the Empirical Mode Decomposition Method. The transfer function was constructed using data produced on an experimental rig, and it was scaled to an existing subway system. The equivalent deformation improved the analysis of the dynamic loads that affect the substructure of the subway tracks because it is considered the primary load that acts on the track and substructure. The acceleration data and the estimated deformations were analyzed with the Continues Wavelet Transform. The equivalent deformation data facilitated the application of a health monitoring system and simplified the development of predictive maintenance programs for the subway or railroad operators. This method better identified cracks in the substructure than using the acceleration data. KW - Health monitoring KW - Transfer function KW - Railroad KW - Substructure failures KW - Dynamic loads PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557480 DO - https://doi.org/10.3389/fmech.2022.858424 SN - 2297-3079 VL - 8 SP - 1 EP - 16 PB - Frontiers Media CY - Lausanne AN - OPUS4-55748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jankuj, V. A1 - Mynarz, M. A1 - Krietsch, Arne A1 - Spitzer, Stefan A1 - Leipik, P. T1 - Experimental investigation of the consequences of acetylene pressure cylinder failure under fire conditions N2 - Acetylene pressure cylinders are widely used in the industrial sector for welding, flame cutting, or heating. Sometimes during work, not only with acetylene cylinders, fires occur and in this case the risk of destruction increases and the behavior of such an exposed cylinder is unpredictable. The purpose of this study is to identify those critical conditions when acetylene cylinders burst and explode in fires. In the present study, acetylene cylinders were exposed to fire conditions. For this purpose, a woodpile as a source of fire was chosen, tested, and evaluated. In addition to the fire condition, this option guaranteed reproducibility and similar conditions for all tests. The individual cylinders were equipped with thermocouples measuring the shell temperature, and half of them were prepared in order to measure the temperatures inside the cylinder. An important factor was the measurement of the amount of pressure that was achieved during the destruction of the cylinder. For this purpose, a pressure transducer was attached to the outlet of the cylinder valve. Exposed to direct fire, they can explode in 10 min, which was confirmed. The critical pressure of 40 bar has been reached in 6 min, followed by destruction after 7 min in fire. Cylinders with internal thermocouples were destroyed when lower pressure was achieved. This confirms the fact that any change of the pressure cylinder affects the original properties. After the tests, the fragments of the selected cylinders were subjected to material tests. The results obtained in these tests are the main source of information for understanding the behavior of acetylene cylinders in fire and the possibility of increasing the safety of intervening rescue services in an emergency. KW - Acetylene KW - Pressure Cylinders KW - Fire KW - Explosion KW - Fireball PY - 2022 DO - https://doi.org/10.1016/j.jlp.2022.104874 VL - 80 SP - 1 EP - 12 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-55755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klimek, André A1 - Stelzner, Ludwig A1 - Hothan, Sascha A1 - Rogge, Andreas T1 - Fire induced concrete spalling in combination with size effects N2 - The size effect has its origin in fracture mechanics and describes the formation as well as propagation of cracks in brittle and solid materials in dependence of the specimen size. However, the size effect in concrete spalling describes the damage behaviour on a macroscopic scale for different sized specimens in case of fire. Concrete spalling is a very complex and yet not fully understood phenomenon. To reduce the effort of fire tests to analyse the spalling behaviour of concrete mixtures, this study investigates the susceptibility to spalling for six different concrete mixtures and three specimen sizes. The sizes were divided in full scale slabs (1.8 m x 1.2 m x 0.3 m), intermediate scale cuboids (0.6 m x 0.6 m x 0.3 m) and small scale cylinders (Ø0.15 m x 0.3 m). For this purpose, a novel test set-up was built to test six intermediate scale or twelve small scale specimens simultaneously to ensure a similar heating regime for every specimen. All specimens were fire exposed on one side and remained unrestrained. A size effect occurred for four of the six concrete mixtures. Compared to the full scale specimens the spalling was reduced significantly for all smaller specimen sizes. Additionally, spalling did not occur for the small scale specimens. The results show that the specimen size is an essential parameter to investigate the susceptibility to spalling of a concrete mixture. For future investigations the testing conditions must be adjusted for the intermediate scale specimens to recreate the conditions of the slabs. KW - Concrete KW - Spalling KW - Size effect KW - Fire test PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-559231 DO - https://doi.org/10.1617/s11527-022-02051-2 VL - 55 IS - 8 SP - 1 EP - 14 PB - Springer AN - OPUS4-55923 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michalchuk, Adam T1 - The Mechanochemical Excitation of Crystalline LiN3 N2 - Mechanochemical reactions are driven by the direct absorption of mechanical energy by a solid (often crystalline) material. Understanding how this energy is absorbed and ultimately causes a chemical transformation is essential for understanding the elementary stages of mechanochemical transformations. Using as a model system the energetic material LiN3 we here consider how vibrational energy flows through the crystal structure. By considering the compression response of the crystalline material we identify the partitioning of energy into an initial vibrational excitation. Subsequent energy flow is based on concepts of phonon–phonon scattering, which we calculate within a quasi-equilibrium model facilitated by phonon scattering data obtained from Density Functional Theory (DFT). Using this model we demonstrate how the moments (picoseconds) immediately following mechanical impact lead to significant thermal excitation of crystalline LiN3, sufficient to drive marked changes in its electronic structure and hence chemical reactivity. This work paves the way towards an ab initio approach to studying elementary processes in mechanochemical reactions involving crystalline solids. KW - Energetic materials KW - Ab initio simulation KW - DFT KW - Mechanochemistry PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-559310 DO - https://doi.org/10.1039/d2fd00112h SP - 1 EP - 20 PB - Royal Society of Chemistry AN - OPUS4-55931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Henning, Ricky A1 - Sturm, Patrick A1 - Geddes, D.A. A1 - Keßler, S. A1 - Walkley, B. A1 - Gluth, Gregor T1 - The influence of curing temperature on the strength and phase assemblage of hybrid cements based on GGBFS/FA blends N2 - Hybrid cements are composites made of Portland cement or Portland clinker and one or more supplementary cementitious materials like slag, fly ash or metakaolin, activated with an alkali salt. To date, their hydration mechanism and the phase formation at various temperatures is insufficiently understood, partly due to the large variability of the raw materials used. In the present study, three hybrid cements based on ground granulated blast furnace slag, fly ash, Portland clinker and sodium sulfate, and an alkali-activated slag/fly ash blend were cured at 10 and 21.5°C, and subsequently analyzed by XRD, 27Al MAS NMR, and TGA. The compressive strength of the hybrid cements was higher by up to 27% after 91-day curing at 10°C, compared to curing at 21.5°C. The experimental results as well as thermodynamic modeling indicate that the differences in compressive strength were related to a different phase assemblage, mainly differing amounts of strätlingite and C-N-A-S-H, and the associated differences of the volume of hydration products. While the strätlingite was amorphous to X-rays, it could be identified by 27Al MAS NMR spectroscopy, TGA and thermodynamic modeling. The microstructural properties of the hybrid cements and the alkali-activated slag/fly ash blend as well as the compatibility between thermodynamic modeling results and experimental data as a function of curing temperature and time are discussed. KW - Hybrid cements KW - Strätlingite KW - Thermodynamic modelling KW - Hydration PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557767 DO - https://doi.org/10.3389/fmats.2022.982568 SN - 2296-8016 VL - 9 SP - 1 EP - 16 PB - Frontiers AN - OPUS4-55776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kremberg, Jan A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Fire tests of carbon tension members for lightweight constructions N2 - Vorstellung der Brandversuche im Rahmen des Projektes NeZuCa an Carbonzuggliedern für den Brückenbau. T2 - ClimateChange@FireScience CY - Berlin, Germany DA - 10.11.2022 KW - Fire tests KW - Carbon KW - Lightweight constructions KW - Fire Science PY - 2022 AN - OPUS4-56302 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Boschmann Käthler, C. A1 - Ebell, Gino A1 - Keßler, S. A1 - Schiegg, Y, A1 - Dauberschmidt, C. A1 - Angst, U. M. T1 - A comparison of methods to assess the resistance of reinforcing steel against chloride‐induced corrosion in concrete - Particular consideration of 12% chromium steel N2 - The critical chloride content C(crit) is an indicator for the corrosion resistance of reinforcing steels in concrete. In this article, several experimental methods for determining the critical chloride content C(crit) of mild and an alloyed (12% Cr) steel in cementitious materials are compared. The methods used include accelerated polarization tests and tests using more natural (unpolarized) conditions in which chloride ingress occurs by diffusion and capillary uptake. The advantages and disadvantages of the methods are discussed, in particular, with the objective of reaching a compromise between applicability to practice and feasibility in laboratory testing. KW - Chloride‐induced corrosion KW - Critical chloride content KW - Reinforced concrete KW - Testing methods PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-529751 DO - https://doi.org/10.1002/maco.202112826 SN - 0947-5117 N1 - This article has been published in 2021 as an "Early View" version with the DOI 10.1002/maco.202112609. VL - 73 IS - 3 SP - 306 EP - 325 PB - Wiley-VCH CY - Weinheim AN - OPUS4-52975 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steinbock, O. A1 - Bösche, T. A1 - Ebell, Gino A1 - Kaplan, F. A1 - Marzahn, G. T1 - Erfahrungen aus dem Rückbau der Brücke am Altstädter Bahnhof in der Stadt Brandenburg N2 - Bei der Brücke Altstädter Bahnhof handelte es sich um eine große Spannbetonkonstruktion, die einen elementaren Ver­kehrsknotenpunkt in der Stadt Brandenburg an der Havel bil­dete. Entgegen üblichen Spannbetonkonstruktionen mit kleinen Bündelspanngliedern kamen beim Haupttragwerk in Längsrich­tung großformatige Spannblockspannglieder zum Einsatz. Im Fall der vorliegenden Brücke setzte sich das Spannglied aus 392 ovalen Einzeldrähten aus Hennigsdorfer Produktion zusam­men, welche als spannungsrisskorrosionsgefährdet gelten. Bei Bauwerkserkundungen wurde ein hoher Versprödungsgrad der Spannstähle festgestellt, sodass die Brücke am 19.05.2021 ge­sprengt werden musste. Zuvor traten im Bereich detektierter Spanndrahtbrüche von außen erkennbare Längsrisse in den Stegen anstatt von üblicherweise quer gerichteten Biegerissen an der gezogenen Randfaser auf. Die abweichende Schadens­äußerung im Falle einer Spannstahlschädigung brachte das Bundesministerium für Digitales und Verkehr (BMDV) dazu, weitergehende Untersuchungen durchzuführen. In Zusammen­arbeit mit dem Landesbetrieb Straßenwesen Brandenburg, der Hochschule für Technik und Wirtschaft Dresden sowie der Bundesanstalt für Materialforschung und ­prüfung (BAM) wur­den experimentelle Untersuchungen in­situ konzipiert und durchgeführt. Im Konkreten wurde an zwei Messstellen eine gezielte Schädigung des großformatigen Spannglieds vorge­nommen, um das zuvor vorgefundene Schadensbild nach­zuvoll ziehen und validieren zu können. Konzept, Ergebnisse aus den Untersuchungen und Erkenntnisse für gleichartig ausge­führte Bauwerke sind Gegenstand des ersten Beitrags (Teil 1). Der zweite Teil [1] wird sich im Schwerpunkt den verwendeten Messverfahren und Monitoringsystemen widmen, welche die Durchführung des Versuchs begleiteten. KW - Korrosion KW - Spannungsrisskorrosion KW - Spannstahl KW - Wasserstoff PY - 2022 DO - https://doi.org/10.1002/best.202200051 VL - 117 IS - 1 SP - 572 EP - 580 PB - Ernst & Sohn CY - Berlin AN - OPUS4-55329 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hupp, Vitus A1 - Schartel, Bernhard A1 - Flothmeier, K. A1 - Hartwig, A. T1 - Adhesive Tapes in Bonded Materials Fire Risk or Protective Layer? N2 - In the recent years, more and more products in construction and automotive industry are bonded by adhesive tapes instead of mechanical fasteners but there is no sufficient understanding of how these bonded, layered materials behave in fires. Our research project gives an insight of how adhesives and substrates interact with each other in different fire scenarios and how flame retardants function in pressure sensitive adhesive (PSA) tapes. A systematic investigation on the burning behavior of PSA tapes as free-standing films, as top layers on different substrates and as sandwich-like adhesive joints was performed. The burning behavior of free-standing PSA tapes and those used as a coating was significantly improved by using phosphorus-based flame retardants. Furthermore, it was shown that, depending on tape structure and substrate, the PSA tape can lower the fire risk by acting as an intermediate protection layer in bonded materials. T2 - Fire and Polymers CY - Napa, California, USA DA - 05.06.2022 KW - Pressure Sensitive Adhesives KW - Tapes KW - Fire Behavior KW - Bonded Materials PY - 2022 AN - OPUS4-55094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seyhan, E. A1 - Ebell, Gino A1 - Jimenez, D. A1 - Chavez, J. A1 - Sanchez Alvarez, G T1 - Evaluation of SACI performance on reinforced concrete structures N2 - Surface applied corrosion inhibitors (SACI) are widely used to mitigate corrosion process of steel reinforcement in concrete. But they remain controversial as to their effectiveness and the ability to compare materials from different manufacturers and technologies. They are applied onto the surface of hardened concrete and penetrate towards steel reinforcement. This paper discusses the corrosion inhibition performances of dual-phase surface applied corrosion inhibitor and the efficiency of the corrosion inhibitor is assessed by selected testing procedures in BAM laboratories. T2 - ACHE 2022 CY - Santander, Spain DA - 20.06.2022 KW - Corrosion KW - Inhibitor PY - 2022 AN - OPUS4-55095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mensinger, M. A1 - Fischer, O. A1 - Oberhaidinger, F. A1 - Stimmelmayer, L. A1 - Ebell, Gino A1 - Babutzka, Martin T1 - Grouted joint for integral composite frame bridges suitable for hot dip galvanizing N2 - Due to the corrosion resistance of carbon steel, bridge constructions are currently protected against corrosion by applied coating systems. These coating systems need to be renewed after approximately 25 50 years. Galvanized constructions without any welding areas at the construction site could be prepared as grouted joints and can be used without any renewing for about 100 years. T2 - Intergalva 2022 CY - Rome, Italy DA - 20.06.2022 KW - Corrosion KW - Galvanized steel KW - Bridge PY - 2022 AN - OPUS4-55096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Zündgefahren durch Funken - Grundlagen und Maßnahmen zum Explosionsschutz N2 - Hersteller von Geräten für den bestimmungsgemäßen Gebrauch in explosionsfähigen Bereichen müssen, wenn sie unter die Richtlinie 2014/34/EU fallen, für das Inverkehrbringen in EU-Mitgliedsstaaten eine Konformitätsbewertung durchführen. Dazu gehört eine Zündgefahrenbewertung, bei der auch nichtelektrische Zündquellen betrachtet werden müssen, zu denen die mechanischen Schlagvorgänge gehören. Bei dieser Zündquellenart kommt es infolge eines Schlages und/oder Reibens eines Bauteils auf ein anderes zu einer Energieumwandlung. Dadurch kommt es zu einer Temperaturerhöhung an der Kontaktstelle sowie unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Reibflächen als auch die abgetrennten Partikel stellen potentielle Zündquellen explosionsfähiger Atmosphären dar. Edelstahl ist für Geräte für die Verwendung zum bestimmungsgemäßen Gebrauch im explosionsgefährdeten Bereich insbesondere in der Chemie ein wichtiger Konstruktionswerkstoff. Die Ergebnisse des Forschungsprojektes "Entwicklung normativer Anforderungen an explosionsgeschützte nichtelektrische Geräte resultierend aus der Zündfähigkeit mechanisch erzeugter Schlagfunken (NAMES)" zeigen, dass Schlagvorgänge mit Edelstählen eine erhebliche Zündgefahr von explosionsfähigen Brenngasgemischen darstellen können. Dabei bestehen jedoch mitunter deutliche Unterschiede zwischen den verschiedenen Brenngasgemischen. Besonders hohe Zündwahrscheinlichkeiten konnten bei Brenngasgemischen mit Brenngasen der IEC-Explosionsgruppe IIC beobachtet werden, die Acetylen bzw. Wasserstoff als Brenngas enthielten. Schläge im Wasserstoff/Luft-Gemisch waren dabei jedoch bedeutend zündwirksamer. In diesem Gasgemisch konnte bei niedrigen maximalen Schlagenergien bis 60 J sogar eine mitunter höhere relative Zündhäufigkeit beobachtet werden als bei Versuchen mit unlegiertem Baustahl. T2 - Ausbildung zum Explosionsschutzbeauftragten CY - Essen, Germany DA - 21.06.2022 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Zündgefahrenbewertung KW - Funkenarme Werkzeuge KW - Funkenfreie Werkzeuge PY - 2022 AN - OPUS4-55098 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -