TY - CONF A1 - Ebell, Gino T1 - Potentialfeldmessung in Theorie und Praxis N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbedingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanierungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz T2 - Vorlesung TU-Berlin CY - Berlin, Germany DA - 30.06.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-55156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Development of an analysis and testing concept for the evaluation of impact targets in the mechanical safety testing of dangerous goods packagings N2 - The mechanical and geometrical properties of impact targets greatly influence the outcome of a drop test. The International Agreement concerning the International Carriage of Dangerous Goods by Road (ADR) as well as ISO 2248 describe the characteristics of impact targets for drop tests of dangerous goods packagings. According to these regulations, the impact target’s surface needs to be unyielding, under testing conditions non-deformable, flat, and integral with a mass at least 50 times that of the heaviest packaging to be tested. The problem is that many production facilities, especially manufacturers of corrugated fibreboard boxes, do not have their own testing device with the required 50 times mass ratio of the impact target for a regulation compliant drop test during series production. Furthermore, at UN level it is considered necessary to revise these requirements. In the present paper, the impact target requirements are examined in detail and compared with those in other technical areas (e.g., impact target for container for the transport of radioactive materials). A research method is being developed to investigate the dependency between the mass ratio of the packaging and the target as well as the damage resistance of a drop tested package in relation to specific design characteristics. The results are of high relevance for industry purposes and intended to ensure a uniform level of safety assessment for the mechanical testing of dangerous goods packagings. T2 - IAPRI Bangkok 2022, 23rd World Packaging Conference CY - Online meeting DA - 12.06.2022 KW - Corrugated fibreboard boxes KW - Dangerous goods packagings KW - Drop test KW - Impact target KW - Structural dynamics PY - 2022 AN - OPUS4-55121 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John A1 - Vogler, Nico A1 - Goedecke, Thomas T1 - Flow properties of powdery or granular filling substances of dangerous goods packagings - Comparison of the measurement of the angle of repose and the determination of the Hausner ratio N2 - To ensure safety when transporting dangerous goods, it is important to specify the flow properties of the respective solid filling substance of the packagings. For this purpose, the angle of repose is currently used for the UN approvals in Germany. Measurements were carried out on 12 powdery or granular substances applying the angle of repose measuring methods customary in the test centres. The results of the methods differ significantly from each other. In addition, some of the techniques cannot be applied for very cohesive or coarse-grained materials. The results for the angle of repose show a strong scatter for some constellations (coefficient of variation more than 20 %). Safety during transport of dangerous goods cannot be guaranteed with this currently practiced system of measuring the angle of repose. As a consequence, an alternative parameter to characterize the flow properties of bulk materials should be used in the recognized test centers for dangerous goods packagings, such as the Hausner ratio. This approach leads to more precise test results for the substances examined (maximum coefficient of variation 2.8 %). It also has advantages in terms of applicability and occupational safety. Since the flow properties are safety-relevant, both in terms of mechanical safety and safety against the release of dangerous substances, the testing practice in the recognized test labs should be improved and standardized. T2 - IAPRI Bangkok 2022 23rd World Packaging Conference CY - Online meeting DA - 12.06.2022 KW - Sift-proofness KW - Powders KW - Flow properties KW - Flowability KW - Angle of repose KW - Hausner ratio PY - 2022 AN - OPUS4-55103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando T1 - Prüfung von Spannstählen N2 - Ein Stand zum WIPANO-Projekt Spannstahlsicherheit wurde auf Anfrage in einer Gemeinschaftssitzung des AK "Eisen und Stahl" sowie des AK "Korrosionsuntersuchung und -überwachung" der Gesellschaft für Korrosionsschutz e.V. (GfKORR) präsentiert. Das Projekt hat die Verbesserung der produktspezifischen Prüfnorm ISO 15630-3 als Ziel. Vorgestellt wurden die Wahl der neu entwickelten Wasserstoffbeladung mit galvanostatischer kathodischer Polarisation und die Frage, ob die Prüfung an Lieferoberflächen sinnvoll ist. T2 - Gemeinschaftssitzung des AK "Eisen und Stahl" sowie des AK "Korrosionsuntersuchung und -überwachung" der Gesellschaft für Korrosionsschutz e.V. (GfKORR) CY - Online meeting DA - 23.06.2022 KW - ISO 15630-3 KW - Spannstahl KW - Spannungsrisskorrosion KW - Wasserstoff KW - Permeationsmessung PY - 2022 AN - OPUS4-55105 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fladt, Matthias A1 - Weise, Frank A1 - Wieland, Marko T1 - Internal water-repellent treatment - a novel strategy for mitigating alkali-aggregate reaction in concrete road pavements N2 - To prevent future alkali-aggregate reaction (AAR) damage, which has occurred frequently in the German highway network in recent years, a new regulation has been drafted. This regulation severely limits the use of alkali-sensitive aggregates by requiring that their suitability be verified by certified inspectors using newly developed AAR concrete tests that involve the external supply of alkali. This has led to a significant limitation in the number of aggregates usable for concrete pavements. A novel AAR avoidance strategy is now being pursued, which aims to enable the use of borderline alkali-sensitive aggregates through the application of an internal water-repellent treatment. The addition of water repellents during concrete production should significantly reduce the ingress of water and external de-icing salts into the concrete pavement, thus reducing the potential for AAR damage. This paper presents the results of laboratory tests to assess the suitability of this new AAR prevention strategy. Representative, highly AAR-susceptible road paving concrete made with an alkali-sensitive greywacke and various water repellents were used as the basis for these experiments. The tests for concrete suitability included determining the conventional fresh and hardened concrete properties as well as concrete prism tests with external alkaline supply. Building on these results, laser-induced breakdown spectroscopy (LIBS) analyses of de-icing-salt intrusion as well as microscopic examinations for verification of the AAR characteristics were carried out. The results of the AAR concrete tests with external alkaline supply support the conclusion that, when hydrophobic agents containing a suitable active ingredient are used, the AAR damage process in road paving concrete can be sufficiently prevented. T2 - 16th International Conference on Alkali-Aggregate Reaction in Concrete CY - Lisbon, Portugal DA - 31.05.2022 KW - Concrete pavements KW - Internal water-repellent treatment KW - Preventive measures KW - Testing for potential alkali-aggregate reaction PY - 2022 AN - OPUS4-55185 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Fugenfüllungen - Anforderungen, Eigenschaften, Prüfungen, Dauerhaftigkeit N2 - Fugenfüllungen im kommunalen Stadtstrassenbau unterliegen besonderen mechanischen Beanspruchungen. Hier kommt es bereits bei der Planung darauf an, Fugenausführungen und insbesondere Fugenfüllstoffe bewusst nach ingenieurtechnischen Gesichtspunkten auszuwählen. Dazu ist das ingenieurtechnische Verständnis der relevanten Fugenfüllstoffe - Funktionsweise, Leistungskriterien, Prüfungen, Dauerhaftigkeit - von entscheidender Bedeutung. Der Vortrag erläutert nicht nur die maßgebenden Fugenfüllstoffe unter den vorgenannten Schwerpunkten, sondern stellt auch das Verständnis zu den Rahmenbedingungen, Grundlagen und Wirkmechanismen des entsprechenden technischen Regelwerkes her. Neueste Entwicklungen werden den Praxisvertretern näher gebracht und erläutert. Die Zusammenhänge und Strategien zur Weiterentwicklung der „Betonstrasse der Zukunft“ werden diskutiert und dargestellt. T2 - Qualitätsgemeinschaft Städtischer Strassenbau (QGS) - Weiterbildung für technisches Führungspersonal CY - Berlin, Germany DA - 14.06.2022 KW - Kommunale Infrastruktur KW - Betonfahrbahndecken KW - Qualitätssicherung KW - Verfügbarkeit PY - 2022 AN - OPUS4-55070 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Prestressed Concrete Structures with Concentrated Tendons - Structural Damage due to Hydrogen-Induced Stress Corrosion Cracking N2 - In the course of the deconstruction of the "Bridge of the 20th anniversary of the GDR" at the Altstädter Bahnhof in Brandenburg a. d. Havel, new information on the initiation of hydrogen-induced stress cracks was obtained. BAM was commissioned by the Brandenburg State Road Administration to participate in a corresponding joint project which is financed by the Federal Ministry for Digital and Transport. The added value of the new information gained in this project goes beyond the specific structure. It describes unexpected new damage patterns that can be transferred to other structures with concentrated tendons (tendon block method and Baur-Leonhardt method) and were previously unknown in this form. These should be made known to other developers to enable them to initiate any necessary actions. T2 - Eurocorr 2022 CY - Berlin, Gemany DA - 29.08.2022 KW - Korrosion KW - Corrosion KW - Hydrogen KW - Stress Cracking PY - 2022 AN - OPUS4-55613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Le, Quynh Hoa A1 - Bettge, Dirk T1 - Electrochemical behaviors of casing steel/mortar interface in CO2 saturated aquifer fluid N2 - To reveal the corrosion resistance of casing steel/mortar interface in CO2 injection condition, sandwich samples were prepared and exposed up to 20 weeks in aquifer fluid under 10 MPa and 60 °C. Cross section analysis revealed the crevice corrosion as main mechanism instead of pitting corrosion despite very high concentration of Cl in NGB. EDS element line scan analysis of the 20-week-exposed metal/mortar coupon showed Chloride distribution, which still not reached the metal/mortar interface, explaining no pitting was observed. It was confirmed that FeCO3 cannot protect the steel surface in CO2 saturated NGB. To verify the protective possibility of passivation happened on casing steel/mortar interface, simulated pore solution was synthesized and used to passivate the steel for 42 days. OCP and EIS confirmed the formation of passive layer. The 42 day passivated layer was broken during the first minute of exposure in CO2 saturated NGB. However, due to high concentration of Ca2+, a new carbonate CaCO3 dense layer was formed, increased the corrosion resistance of steel surface. T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Corrosion KW - Geothermal KW - CO2 KW - Mortar PY - 2022 AN - OPUS4-55621 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Aristia, G. T1 - A Coating System for Corrosion Protection of Carbon Steel as an Alternative for High Alloyed Materials N2 - The screening of coatings shows that the modification by adding individual pigment was not sufficient to protect carbon steel even during a short-term exposure, indicated by the discoloration after only seven days of exposure. Electrochemical tests indicated that the coating cathodically protects carbon steel or slows down the corrosion reaction. A long-term exposure test confirmed that the PANI/SiO2 modified coating successfully protects the carbon steel in the Sibayak artificial geothermal water at 150 °C for 6 months. T2 - European Geothermal Congress CY - Berlin, Germany DA - 17.10.22 KW - Corrosion KW - Geothermal KW - Coatings KW - Polyaniniline KW - Silicate PY - 2022 AN - OPUS4-56084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Railway-induced ground and building vibrations – Analysis in frequency-wavenumber domain and fast prediction with approximate models N2 - A simple and fast prediction scheme is presented for train-induced ground and building vibrations. For the emission, finite-element boundary-element or multiple-beam-on-continuous-soil models of the track have been analysed and approximated by faster track-on-Winkler-soil models. The vehicle-track interaction due to irregularities yields the excitation forces. For the transmission of waves in the soil, the wavenumber integral of the compliance of layered soils has been evaluated. The calculation time is reduced for the prediction by using the solution of a homogeneous half-space with a frequency-dependent wave velocity (the dispersion) of the soil. For the immision, many 2 and 3-dimenisonal finite-element building models have been investigated, and a good approximation has been established by a 1-dimensional soil-wall-floor model. In addition, the axle sequence of the train, the quasi-static and the “scattered” response of the soil, and the wave propagation from a tunnel to a pile foundation of a building have been included. T2 - ISMA-Conference CY - Leuven, Belgium DA - 12.09.2022 KW - Ground vibration KW - Building vibration KW - Railways KW - Simple and fast prediction PY - 2022 AN - OPUS4-56038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schendler, Thomas T1 - Arbeit der Kommission für Anlagensicherheit (KAS) N2 - Kurze Vorstellung der KAS; Aktuelles Arbeitsprogramm; Kurze Darstellung von Ergebnissen; Stand Diskussion/Verfolgung von Ereignissen/Störfällen; Kurze Vorstellung der Ergebnisse des FuE-Vorhabens „Umfassende systematische Auswertung von Störfällen und sonstigen Ereignissen in industriellen Anlagen“ T2 - Kolloquium Anlagensicherheit/Störfallvorsorge CY - Dresden, Germany DA - 29.09.2022 KW - KAS KW - Ereignisse KW - Störfälle PY - 2022 AN - OPUS4-56125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Seifert, Lando A1 - Ebell, Gino T1 - Vorstellung Projektergebnisse Wipano Vorhaben Spanntahlsicherheit N2 - Diese Präsentation stellt die Ergebnisse des abgeschlossenen WIPANO Vorhabens "Spannstahlsicherheit" vor, welches von der BAM in Kooperation mit dem Stahlwerks Annahütte und der Max Aicher GmbH bearbeitet wird. Es werden die Projektziele näher beleuchtet und verschiedentliche Highlights der erzielten Untersuchungsergebnisse vorgestellt. T2 - DIN-Ausschussitzung des NA 062-01-77 AA "Korrosionsprüfverfahren" CY - Berlin, Germay DA - 19.10.2022 KW - Korrosion KW - Spannstahl KW - Spannbetonbauwerke KW - Spannungsrisskorrosion KW - Wasserstoffversprödung PY - 2022 AN - OPUS4-56059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer A1 - Zirker, Stefan T1 - Photothermal determination of thermal properties of concrete – a method evaluation N2 - The evaluation of thermal properties is probably an underrated tool for the onsite health monitoring of concrete structures. The photothermal approach offers a possibility to realize a real onsite measurement. This contribution presents the application of the photothermal approach under lab conditions on three different concrete types. The obtained results were compared with those of a commercial device based on the Transient Plane Source (TPS) method. Both agreed well within the estimated uncertainty ranges and therefore demonstrate the applicability of the photothermal method for this kind of investigations. First results of a concrete sample with different water contents support the potential of this method for the characterization of concrete in general. T2 - NDTCE 2022 CY - Zurich, Switzerland DA - 16.8.2022 KW - Thermal effusivity KW - Thermal conductivity KW - Moisture PY - 2022 AN - OPUS4-56063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grohmann, Maria A1 - Niederleithinger, Ernst T1 - Anwendung der Reverse-Time Migration auf Ultraschall-Echo-Daten in der zerstörungsfreien Prüfung von Betonbauteilen N2 - Das Ultraschall-Echo-Verfahren ist eine klassische zerstörungsfreie Prüftechnik zur Geometriebestimmung sowie Schadensanalyse von Betonkonstruktionen. Um die Abbildung der Ultraschalldaten von komplexen Betonstrukturen zu verbessern, haben wir die Reverse-Time Migration (RTM) aus der Seismik auf die zerstörungsfreie Prüfung im Bauwesen übertragen. In einer Vorstudie haben wir einen 2D akustischen RTM Code verwendet und an realen Ultraschalldaten, die an einer Betonfundamentplatte aufgenommen wurden, getestet. Im Vergleich mit dem herkömmlichen Rekonstruktionsalgorithmus für Ultraschalldaten, der Synthetic Aperture Focusing Technique (SAFT), zeigten die akustischen RTM-Ergebnisse eine deutliche Verbesserung in der Abbildung der inneren Struktur der Betonfundamentplatte. Vertikale Reflektoren konnten rekonstruiert werden, was mit dem herkömmlichen Abbildungsverfahren nicht möglich war. RTM ist, im Gegensatz zu SAFT, eine wellengleichungsbasierte Migrationsmethode und beruht auf der numerischen Lösung der vollständigen Wellengleichung. Die Vorteile sind, dass der Algorithmus sämtliche Informationen des Wellenfeldes verwendet und daher verschiedene Welleneffekte wie z.B. Multipathing berücksichtigt werden können. Die RTM bietet damit die Möglichkeit auch stark geneigte Reflektoren sowie Streukörper mit komplexen Geometrien darzustellen. Ein Nachteil ist jedoch die lange Rechenzeit und der hohe Bedarf an Speicherkapazität. Ein RTM-Algorithmus, der die elastische Wellengleichung anstatt der akustischen verwendet (wie in unserer Vorstudie angewandt), hat das Potenzial, die Abbildungsergebnisse noch weiter zu optimieren. Das liegt daran, dass unsere Ultraschallmessdaten durch Anregung elastischer Wellen generiert werden. In einem ersten Schritt haben wir zwei elastische 2D-RTM-Algorithmen an synthetischen Ultraschalldaten getestet. Diese wurden mit einem Betonmodell, bestehend aus mehreren Stufen und kreisförmigen Lufteinschlüssen, erzeugt. In einem zweiten Schritt wurden reale Ultraschalldaten mit Scherwellenprüfköpfen an einer Betonstufenplatte mit integrierten Hüllrohren aufgenommen. Die Auswertung der realen Daten mit unserem elastischen RTM-Code war ebenfalls erfolgreich. Wir konnten die Abbildungsqualität der Stufen und Hüllrohre im Vergleich zur akustischen RTM und SAFT verbessern. T2 - Tagung Deutsche Geophysikalische Gesellschaft DGG CY - Munich, Germany DA - 07.03.2022 KW - Ultraschall-Echo-Verfahren KW - Reverse Time Migration KW - Synthetic Aperture Focusing Technique PY - 2022 AN - OPUS4-56112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Committee Meeting to WIPANO "Safety of Prestressing Steels" N2 - A conclusion on the WIPANO research project "Safety of Prestressing Steel" was presented in the final committee meeting at the end of the project. The project's exciting findings and recommendations for a new method were discussed with the audience of national and international stakeholders of the prestressing steel industry and representatives of inspection bodies and standardization. T2 - Committee Meeting to WIPANO research Project CY - Online meeting DA - 29.09.2022 KW - ISO 15630-3 KW - Prestressing Steels KW - Hydrogen-induced Stress Corrosion Cracking KW - Hydrogen PY - 2022 AN - OPUS4-56101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fürst, Richard A1 - Häßler, Dustin A1 - Hothan, Sascha T1 - Research Project FIRESTEMIC - Results and Recommendations N2 - The presentation summarizes the results of the research project. T2 - Workshop 2022 - Feuerwiderstand von Stahlzuggliedern mit reaktiver Brandschutzbeschichtung CY - Berlin, Germany DA - 06.09.2022 KW - Fire tests KW - Intumescent coating KW - Steel KW - Tension member PY - 2022 AN - OPUS4-55700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Wasserstoff - Kryogene Anwendungen N2 - Wasserstoff wird als ein potenzieller alternativer Energieträger gesehen, mit dem die für 2050 gesetzten Klimaziele erreicht werden könnten. Der Transport von Wasserstoff ist mittels verschiedener Speichertechniken möglich, von denen der kryogene Transport mit den größten volumetrischen Energiedichten einhergeht. Hierdurch eignen sich diese Speicher besonders für die energieintensiven Verkehrsmittel im Land-, See- und Flugverkehr. Im Vortrag werden Speichertechniken, Gefahren im Umgang mit kryogenen Gasen sowie bisherige Störfälle dargestellt. Darauf aufbauend wird ein Teil der aktuellen Forschungsarbeit an der BAM vorgestellt, die die Sicherheit dieser Speicher unter außergewöhnlichen Belastungen adressiert. T2 - 26. Gefahrgutkongress Mecklenburg-Vorpommern CY - Rostock, Germany DA - 03.11.2022 KW - Wasserstoff KW - H2 KW - LNG KW - LH2 KW - Tank PY - 2022 AN - OPUS4-56181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Entwicklung der Potentialfeldmessung –forschung, Regelwerk, Fortbildung N2 - Ein Übersichtsvortrag zur Entwicklung der Prüfmethode zu einem etablierten und geregelten Messverfahren für die Korrosionszustandsermittlung von Stahlbetonbauwerken. T2 - GfKORR Jahrestagung - Aktuelles aus der Korrosionsforschung - Nutzen und praktische Anwendungen CY - Frankfurt a. M., Germany DA - 08.11.2022 KW - Potentialfeldmessung KW - Korrosion KW - Stahlbeton KW - Korrosionsprüfung PY - 2022 AN - OPUS4-56206 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Zündgefahren durch Funken-Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA22-00188-050-E) im Haus der Technik (HdT) - Außeninstitut der RWTH Aachen und der Universität Duisburg-Essen, 45127 Essen CY - Essen, Germany DA - 08.11.2022 KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Mechanischer Explosionsschutz KW - Nichtelektrischer Explosionsschutz PY - 2022 AN - OPUS4-56211 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Hille, Falk A1 - Baeßler, Matthias A1 - El-Athman, Rukeia T1 - Research Data Management of Structural Health Monitoring Projects and Subsequent Applications of Artificial Intelligence Methods N2 - Structural health monitoring (SHM) intends to improve the management of engineering structures. The number of successful SHM projects – especially SHM research projects – is ever growing, yielding added value and more scientific insight into the management of infrastructure asset. With the advent of the data age, the value of accessible data becomes increasingly evident. In SHM, many new data-centric methods are currently being developed at a high pace. A consequent application of research data management (RDM) concepts in SHM projects enables a systematic management of raw and processed data, and thus facilitates the development and application of artificial intelligence (AI) and machine learning (ML) methods to the SHM data. In this contribution, a case study based on an institutional RDM framework is presented. Data and metadata from monitoring the structural health of the Maintalbrücke Gemünden for a period of 16 months are managed with the RDM system BAM Data Store, which makes use of the openBIS data management software. An ML procedure is used to classify the data. Feature engineering, feature training and resulting data are performed and modelled in the RDM system. T2 - 11th International Conference on Bridge Maintenance, Safety and Management (IABMAS2022) CY - Barcelona, Spain DA - 11.07.2022 KW - Research data management KW - Structural health monitoring KW - Artificial intelligence PY - 2022 AN - OPUS4-55494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick A1 - Schneider, Ronald A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Baeßler, Matthias T1 - Sensorbasierte Systemidentifikation N2 - Die aktuelle Instandhaltungsstrategien von Ingenieurbauwerken arbeiten zustandsbasiert und stützen sich auf visuelle Inspektionen in kurzen, starren Intervallen. Beim Übergang zu Predicitive-Maintenance-Strategien können Sensordaten eigesetzt werden um Prognosemodelle der Bauwerke zu aktualisieren. Ein erster Schritt hierzu ist die sensorbasierte Systemidentifikation. T2 - Abschlussveranstaltung AISTEC CY - Berlin, Germany DA - 02.05.2022 KW - Systemidentifikation KW - Strukturmonitoring PY - 2022 AN - OPUS4-55495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald A1 - Simon, Patrick A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Baeßler, Matthias T1 - Belastungsversuch und Methodenvalidierung an der Maintalbrücke Gemünden N2 - Im Projekt AISTEC wurden Methoden entwickelt, die der prädiktiven Instandhaltung von Ingenieurbauwerken dienen. Zur Validierung dieser Methoden wurden an einem Referenzbauwerk - der Maintalbrücke Gemünden - Belastungstests durchgeführt. T2 - Abschlussveranstaltung AISTEC CY - Berlin, Germany DA - 02.05.2022 KW - Belastungsfahrt KW - GNSS KW - Einflusslinien PY - 2022 AN - OPUS4-55496 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Wagner, Adrian A1 - Burkert, Andreas T1 - Field exposure studies of austenitic and duplex stainless steels in tunnel atmospheres N2 - Due to the high corrosivity that are present in road tunnel structures, cleaning and maintenance work on stainless steel components in the tunnels is carried out at regular intervals in the tunnels, which means that parts of the lanes or the whole tunnel have to be temporarily closed. To reduce these traffic disruptions and maintenance costs, it is important to reduce the work that is needed for cleaning and maintenance of stainless steel components in road tunnels. One possibility is the identification and utilization of better suited alternatives to the commonly used austenitic stainless steels AISI 316L and AISI 316Ti. Thus, a field exposure study was carried out in different road tunnels throughout Germany to qualify different duplex and lean duplex stainless steels for tunnel constructions. The proposed scientific poster gives an overview of results after the first three years of exposure in three different road tunnels. Samples of different stainless steels were placed in different areas of the tunnel – at lane height and at the ceiling. Some samples were exposed under sheltered conditions. Pit depths were evaluated on the free surface and in crevice areas after each year of exposure. The investigations show that duplex stainless steels have a comparable or even better corrosion resistance than austenitic steels in tunnel atmospheres. T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Corrosion KW - Atmosphere KW - Tunnel KW - Stainless Steel PY - 2022 AN - OPUS4-55595 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moye, Janis A1 - Sturm, Patrick A1 - Kühne, H.-C. A1 - Keßler, S. A1 - Pistol, K. T1 - Entwicklung und Charakterisierung von alkalisch aktivierten Mörteln für die Betoninstandsetzung - Robustheits- und Dauerhaftigkeitsbetrachtungen N2 - Für die flächige Instandsetzung von Stahlbetonkonstruktionen kommen nahezu ausschließlich zementgebundene Systeme mit hohem Zementgehalt zum Einsatz (1). Bereits 2008 war die Zementproduktion für 5% des weltweiten, anthropogenen CO2-Ausstoßes verantwortlich (2). Um die prozessbedingten CO2-Emissionen zu senken, wird der Zement bereits durch gewisse Mengen an Sekundärrohstoffen wie Flugasche, Silicastaub oder Hüttensandmehl (Hochofenschlacke) substituiert. Das Potenzial für weitere Modifikationen ist inzwischen begrenzt (3). Zudem ist eine hohe Lebensdauer der Konstruktionen in vielen Anwendungsbereichen nur bedingt realisierbar. Spätestens mit Erreichen der geplanten Nutzungsdauer müssen Stahlbetonkonstruktionen mit zementgebundenen Systemen instandgesetzt werden, was im ökonomischen und ökologischen Sinne keine nachhaltige Lösung darstellt. Die Verwendung neuer Baustoffe wie alkalisch aktivierte Mörtel hält sich bisher in Grenzen (4), sodass die Akzeptanz durch praxisnahe Forschung adressiert werden muss. Vorangegangene Forschungsergebnisse zeigen, dass alkalisch aktivierte Bindemittel vielversprechende technische Eigenschaften besitzen. So zeigen sich im Vergleich zu herkömmlichem Portlandzement ein ausgesprochen wirkungsvoller Verbund zu Stahl und Zementmörtel (5), (6), eine hohe chemische Beständigkeit sowie ein Erfolg versprechendes Abwitterungsverhalten bei Frost-Tau-Wechseln (7). Mit diesen Eigenschaften können alkalisch aktivierte Mörtel einen erheblichen Beitrag zur dauerhaften Betoninstandsetzung leisten und somit durch die verringerten CO2-Emmissionen dem Prinzip des nachhaltigen Bauens gerecht werden. Wichtig für die Produktion im größeren Maßstab ist die Verfügbarkeit der möglichen Reststoffe, um eine CO2-positivere Bilanz abzubilden. Im Zuge des Forschungsvorhabens sollen Rezepturen für Instandsetzungsprodukte entworfen werden, die auf alkalisch aktivierte industrielle Reststoffe zurückgreifen und die Anforderungen an konventionelle Instandsetzungsprodukte erfüllen. Hierzu wurden potenzielle Ausgangs-stoffe mit Natriumcarbonat aktiviert und die Verarbeitbarkeit der Leime sowie die Druckfestigkeiten nach sieben Tagen verglichen. Hüttensandmehl reagiert ausreichend mit diesem Aktivator, was sich mit Ergebnissen von (8) und (9) deckt. Es werden 〖CO〗_3^(2-)-Ionen in das System eingebaut, was zu einer anfänglichen Erstarrung des Gefüges durch die Bildung von Carbonaten (Calcit und Hydrotalcit) führt. Nach einer längeren dormanten Phase bilden sich zusätzlich Hydratphasen, die die Festigkeit weiter erhöhen. Weiterhin ist die chemische Zusammensetzung der Schlacken für die Erhärtung und die späteren Eigenschaften von großer Bedeutung (10), (11), was mit einer Parameterstudie im laufenden Jahr an natriumcarbonataktivierten Schlacken näher betrachtet werden soll. Erkenntnisse aus vergleichenden Versuchen durch (12) bestätigen die Einflussnahme der chemischen Zusammensetzung. Die übrigen Reststoffe konnten mit anderen Aktivatoren (z. B. Natriumsilicat und -hydroxid) zu einer Reaktion angeregt werden. Im Hinblick auf die Akzeptanz der alkalisch aktivierten Bindemittel stellen diese Aktivatoren jedoch bei der Herstellung höhere technische Anforderungen an das Personal und die verwendeten Geräte im Vergleich zur konventionellen Beton- und Mörteltechnik. Die Aktivierung mittels Alkalicarbonaten ermöglicht die Herstellung von Beton bzw. Mörtel nach dem üblichen „just add water“-Prinzip (13). Aktuell wird unter Einbindung einer studentischen Abschlussarbeit eine Rezeptur mit Hüttensandmehl hinsichtlich der Frisch- und Festeigenschaften charakterisiert und einer Referenzmischung – basierend auf Portlandzement – gegenübergestellt. Hieraus resultierende Ergebnisse sollen neben den Erkenntnissen aus den Vorversuchen zur Konferenz vorgestellt und ein Ausblick auf die weitere Forschungsarbeit gegeben werden. T2 - Nachwuchswissenschaftler*innenkonferenz 2022 CY - Brandenburg an der Havel, Germany DA - 11.05.2022 KW - Alternative Bindemittel KW - Alkalische Aktivierung KW - Instandsetzung KW - Realkalisierung PY - 2022 AN - OPUS4-55517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. A1 - Romero-Navarrete, J. A. T1 - Experimental test rig for simulating dynamic loads on subway systems N2 - Degradation in substructures, Mexico’s City Subway. Improve predictions using vibration Measurements. Ability to test operating conditions at Laboratory. Improve previous laboratory rig. Control operating conditions. Produce enough data for evaluating actual conditions. T2 - Fifth International Conference on Railway Technology CY - Montpellier, France DA - 22.08.2022 KW - Test rig KW - Simulating KW - Dynamic loads KW - Subway PY - 2022 AN - OPUS4-55568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Potential Mapping - What could we measure and what should we able to detect – guideline B03 of DGZfP N2 - “Electrochemical potential mapping according to guideline B3 of DGZfP (German Society for Non-Destructive Testing) is a recognized technique for the localization of corroding reinforcing steels. Areas of corroding reinforcement steel can be located in a non-destructive manner by means of this procedure. Half‐cell potential measurements are used in order to detect chloride‐induced corrosion. However, it is not recommended in order to assess the risk of carbonation‐induced corrosion. For this purpose, determining the carbonation depth and the concrete cover appears more appropriate. The content of this specification exclusively refers to the application of mobile, local variable reference electrodes, which are only placed on the concrete surface while measuring. The technique distinguishes itself thereby from the range of corrosion monitoring systems with stationary installed reference electrodes and sensor systems, respectively, whereby it is possible to continuously track measurements within the area of the installed electrodes. However, these methods are not dealt with in this specification.” T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Korrosion KW - Potentialfeldmessung KW - Corrosion KW - Half-cell potential KW - Potential mapping PY - 2022 AN - OPUS4-55524 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, S. A1 - Algernon, D. A1 - Arndt, R. A1 - Ebell, Gino A1 - Friese, M. A1 - Grosse, C. U. A1 - Holstein, R. A1 - Niederleithiger, Ernst A1 - Schickert, M. A1 - Schulze, S. A1 - Taffe, A. A1 - Walther, A. A1 - Wolf, J. A1 - Zoega, A. A1 - Zwanzig, M. T1 - Introduction to DIN 4871: Qualification of NDT Personnel in Civil Engineering (NDT‐CE) N2 - Recently, non-destructive testing in civil engineering (NDT-CE), in particular of concrete components, has successfully mastered the leap from research to practice. Several methods have been established for field inspections to determine the concrete cover of reinforcement or to estimate the compressive strength as well as other parameters related to the concrete material. In addition, the application of non-destructive testing is indispensable, if information about the inner structure - such as the location of rebars and tendon ducts or the damage-related condition assessment to detect grouting defects, honeycombs, delamination, or corrosion - is required. Besides the selection of a suitable NDT method and an appropriate inspection system, the reliability of the results depends largely on the person who applies the non-destructive inspection technique and evaluates the inspection results. To ensure a high quality of non-destructive concrete evaluation as well as to keep the uncertainty caused by the inspection personnel to a minimum, structured, consistent, and regulated theoretical as well as practical training of inspection personnel is essential. To close this gap, the subcommittee of education and training (UA-A) within the committee for NDT-CE of the German Society for Non-Destructive Testing (DGZfP) has been reactivated in 2018 to establish uniform training standards for non-destructive concrete inspections in the long term. The subcommittee consists of scientists, practitioners, authorities, and clients. So far, the national standard DIN 4871 “Non-destructive testing - Qualification of NDT personnel in Civil Engineering (NDT-CE)” was developed. This standard considers the civil-industry-specifics, for example, that standards for NDT of concrete, as well as related product standards with a few exceptions, still do not exist at the moment. Within this presentation, the concept, the connection to ISO 9712 and other standards as well as an overview of the recently developed German standard DIN 4871 will be presented. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Non-destrucive testing KW - Civil engineering PY - 2022 AN - OPUS4-55526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, W. A1 - Wilsch, Gerd A1 - Katsumi, N. A1 - Ebell, Gino A1 - Völker, Tobias T1 - Ion distribution in concrete overlay, mapped by laser induced breakdown spectroscopy (LIBS), modified by an embedded zinc anode N2 - Galvanic corrosion protection by embedded zinc anodes is an accepted technique for the corrosion protection of reinforcing steel in concrete. Galvanic currents flow between the zinc anode and the steel reinforcement due to the potential difference that is in the range of a few hundred mV. The ion distribution was studied on two steel reinforced concrete specimens admixed with 3 wt.% chloride/wt. cement and galvanically protected by a surface applied EZ-anode. On both specimens, a zinc anode was embedded and glued to the concrete surface by a geo-polymer-based chloride-free binder. At one specimen, the EZ-anode was operated for 2,5 years, the EZ-anode at the other specimen was not electrically connected to the reinforcement, this specimen serves as a reference. Both specimens have been stored under identical conditions. The ion distribution between the anode (EZ-anode) and cathode (steel reinforcement) was studied by laser-induced breakdown spectroscopy (LIBS) after 7 months, 12 months, and 2,5 years. Results of the LIBS studies on the specimen with activated EZ-anode after 7 months, 12 months, and 2,5 years and of the reference specimen after 2,5 years are reported. Results show that diffusion of ions contributes to the changes in the ion distribution but migration, especially of chlorides towards the EZ-anode is significant despite the weak electric field – several hundred millivolts - generated by the galvanic current. Results show that chloride ions accumulate near the zinc-anode as in water-insoluble zinc-hydroxy chlorides - Simonkolleit. T2 - ICCRRR 2022 CY - Capetown, South Africa DA - 03.10.2022 KW - Korrosion KW - Corrosion KW - LIBS KW - Zinc PY - 2022 AN - OPUS4-55948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Sustainability Meets Flame Retardancy – Fun, Food for Thought, or Future N2 - Überblick über den State-of-the-Art und aktuelle Trends mit den Schwerpunkten: - nachwachsende Rohstoffe in flammgeschützten Polymerwerkstoffen (flammgeschützte Biopolymere und Biokomposite; biomass-basierte Flammschutzmittel, nachwachsende Hilfsstoffe aus Abfallströmen) - Nachhaltigkeit und Flammschutz - Konzepte von Analogie bis Out-of-the-Box. T2 - IK 2022, 10. Institutskolloquium Biozide & Flammschutzmittel - Materialien, Anwendungen und Trends CY - Weißandt-Gölzau, Germany DA - 11.10.2022 KW - Nachhaltigkeit KW - Nachwachsende Rohstoffe KW - Flammschutz KW - Biopolymerkomposite PY - 2022 AN - OPUS4-55983 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Taffe, A. T1 - On the accuracy of tendon localization in concrete using ultrasound N2 - Approaches to the development of a (GUM-) measurement model for the calculation of measurement uncertainties in the localization of tendons in concrete structures using the ultrasonic echo method including demonstration were presented. T2 - 6th International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Reliability KW - Measurement Uncertainty KW - Non-Destructive Testing KW - Existing Concrete Structures PY - 2022 AN - OPUS4-55991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klimek, André A1 - Stelzner, Ludwig T1 - Screening-tests on the susceptibility to spalling of two ordinary concretes N2 - Investigating the spalling behaviour of a concrete mixture using large scale members is complex and expensive. Thus, the susceptibility of concrete to spalling is investigated by means of fire tests on small scale specimens. However, the reduction of the fire exposed surface increases the influence of boundary effects. Macrocracking and the water loss via the lateral surfaces reduce the impact of the thermomechanical and thermohydraulic damage mechanisms and therefore, lower the risk of spalling. Thus, the influence of different restraints on the spalling behaviour of intermediate scaled specimens (Ø0.47 m; h=0.29 m) was investigated for two ordinary concrete mixtures. Both mixtures had the same composition except the type of aggregate. One mixture contained only quartzitic aggregates, whereas the other mixture was made with basalt grit as coarse aggregates. Applied steel rings restrained the thermal expansion of the specimen and prevented the loss of water, whereas applied steel sheet primarily reduced the loss of water during the fire test. Additionally, the fire exposed surface of one specimen of each mixture was pre-dried under controlled climate conditions and fire tested with applied steel rings. The results show a higher spalling volume for the ring restrained specimens compared to the other covering types. Further, the pre-dried boundary zone leads to delayed and decreased occurrence of spalling compared to the non-dried specimens for the concrete with quartzitic aggregates and to a prevention of spalling for the mixture with basalt aggregates. Additionally, the results show that the influence of the thermomechanical behaviour of the coarse aggregates increases with increasing restraint. The restrained conditions of the specimens with applied steel ring are comparable to the conditions in the centre of a large scale member. This test series is a further step for possible concept of steel ring restraint concrete specimens as “screening-tests” in upcoming projects. T2 - 7th International Workshop on Concrete Spalling due to Fire Exposure CY - Berlin, Germany DA - 12.10.2022 KW - Spalling KW - Fire test KW - Concrete KW - Restraint PY - 2022 AN - OPUS4-56023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Achievements and challenges of distributed polymer optical fiber sensors @BAM N2 - Monitoring of construction projects plays increasingly important role in the implementation of growing needs and requirements, especially in geologically difficult areas. This particularly concerns tunnelling and special civil engineering projects. The use of fiber optic sensors for structural health monitoring provides significant economic advantages regarding lower life-cycle costs of the civil infrastructure. We present our achievements in the development of distributed polymer optical fiber sensors based on Rayleigh and Brillouin scattering for early damage detection. T2 - POF Conference CY - Bilbao, Spain DA - 26.09.2022 KW - Distributed POF sensor KW - OTDR KW - OFDR KW - Smart geosynthetics PY - 2022 AN - OPUS4-56031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir A1 - Rohrmann, Rolf T1 - Measurement and evaluation tools for ground and building vibrations from industrial process-es, construction work, traffic and other sources N2 - Vibration measurements have many causes and many technical and natural sources. Problems can sometimes be solved by short-term measurements, but in many cases, a long-term measurement is necessary. In long-term measurements of days, weeks, months and even years, it is easy to collect a huge quantity of raw data, but at the end, the post-processing of these data can be exhausting (for example one-year vibration data of a wind energy tower). A software has been developed which con-sists of measuring and evaluation routines where the measuring routines can operate different meas-uring systems and different measuring cards. The main advantage of this software is the fact that the interesting evaluations can be integrated in the measuring process so that the characteristics of the vibration can be extracted without storing all the raw data. Only important time segments are stored, for example train passages. The overall concept of the software and the main evaluation routines will be described in some details. Examples of our measurement experience will illustrate the capabilities of the software. 1) Surveying construction work in nearby sensitive buildings (for example an old wind tunnel), including a stable alarm system and meaningful vibration limits. 2) Prediction of train-induced vibration for a planned building to prevent annoyance and to improve the building design. 3) Modal analysis and long term measurements of several single- or multi-span, concrete or steel bridges 4) Modal and wave analysis of coupled floors in a historical building (“Neues Palais” at Potsdam). 5) Soil properties of various measurement sites (different routines to evaluate the dispersion). Moreover, from many projects, amplitudes, frequencies, and attenuation laws have been collected and analysed for the different sources such as vibratory or impact pile driving and ground compaction, demolition work with different machines, blasting in quarries and in tunnel works, bomb and mine clearing. T2 - 28th International Congress on Sound and Vibration (ICSV28) CY - Online meeting DA - 25.07.2022 KW - Ground vibration KW - Building vibration KW - Measurement KW - Evaluation KW - Modes and waves PY - 2022 AN - OPUS4-56035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Effects of a varying track and soil stiffness on ground vibrations near railway lines N2 - Usually, geometric irregularities are considered as the main cause of ground vibrations from trains. A varying stiffness of the track, the track support and the soil can also generate ground vibrations. The regular stiffness variation of the track on and between the sleepers results in a deterministic dynamic axle load. The random stiffness variation of the track support yields also dynamic axle loads. The dynamic axle loads are generated by the varying wheel displacements under the static axle load by the acceleration of the unsprung mass of the rail vehicle. The random stiffness variation has a second effect. The pulses from the passage of the static axle loads are superposed regularly to the quasi-static response, but also irregularly to yield a “scattered” part of the axle pulses. The same holds for a random variation of the soil stiffness. All these effects of stiffness variations have been calculated by wavenumber-domain multi-beam track models, a random finite-element soil model and the superposition of axle impulses in a stochastic simulation. The results are confronted with many measurements at different sites. It is concluded that the stiffness variation of the track and the soil generate an important ground vibration component near railway lines. T2 - Railways 2022 CY - Montpellier, France DA - 22.08.2022 KW - Ground vibration KW - Railways KW - Varying track stiffness KW - Varying soil stiffness PY - 2022 AN - OPUS4-56036 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Niederleithinger, Ernst T1 - Practical procedure for the precise measurement of geometrical tendon positions in concrete with ultrasonic echo N2 - Existing concrete structures were usually designed for lifetimes of several decades. The current and urgently required efforts to increase sustainability and protect the environment will likely result in extended service lives up to 100 years. To achieve such objectives, it is required to assess structures over their entire lifecycles. Non-destructive testing (NDT) methods can reliably support the assessment of existing structures during the construction, operational, and decommissioning phases. One of the most important and safety-relevant components of a prestressed concrete structure are the tendons. NDT methods such as the ultrasonic echo method are suitable for both the detection and the localization of the tendons, i.e., the measurement of their geometrical position inside the component. The uniqueness of structures, concrete heterogeneity, and varying amounts of secondary components such as the reinforcement represent obstacles in the application of these methods in practice. The aim of this contribution is to demonstrate a practicable procedure, that can be used in the field to determine the parameters required for the measuring data analysis without extensive knowledge about the investigated components. For this purpose, a polyamide reference specimen is used to show which steps are required to obtain reliable imaging information on the position of tendons from the measurement data. The procedure is then demonstrated on a concrete test specimen that covers various relevant and practice-oriented test scenarios, such as varying tendon depths and component thicknesses. T2 - International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Validation KW - Non-destructive testing KW - Ultrasonic KW - Reconstruction KW - Concrete KW - Tendon duct PY - 2022 AN - OPUS4-55999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Epple, Niklas A1 - Liao, Chun-Man T1 - Recent advances in (ultra)sonic active and passive monitoring of reinforced and prestressed concrete structures N2 - In addition to already established structural monitoring methods such as deformation, inclination or strain gauges or acoustic emission sensors, sonic or ultrasonic monitoring might provide valuable information about the condition or alteration of a structure. Sensors such as geophones, recording ambient noise in the sonic and subsonic frequency range can provide information beyond modal analysis by using interferometric methods. Wave velocities determined by this method are related to the elastic properties and stiffness of material and structure and can be converted into damage indicators. Embedded active ultrasonic transducer networks can provide more detailed insight about deterioration or damages again, using interferometric technologies. This approach is extremely sensible, detecting relative change in velocity on down to 10-5. These methods, including benefits and remaining challenges, are demonstrated using data from a test structure at BAM’s test site demonstrating the case of prestress loss, and data from an actual bridge still under traffic. T2 - International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Monitoring KW - Ultrasonic KW - Non-destructive testing KW - Coda wave KW - Bridge PY - 2022 AN - OPUS4-56000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Bio, Waste, Non-vegan – Fun, Food for Thought, or Future N2 - Overview of the state of the art and current trends with the main topics: - renewable sources in flame retardant polymers (flame retarded bio-polymers and biocomposites; bio-flame retardants, renewable adjuvants from industrial waste) - flame retardancy meets sustainability - concepts between analogy and out-of-the-box. T2 - 18th SKZ International Conference on Trends in Fire Safety and InnovativeRFlame retardants for Plastics CY - Würzburg/Rottendorf, Germany DA - 27.09.2022 KW - Bio-polymer KW - Bio-composite KW - Renewable source KW - Renewable adjuvants KW - Vitrimer KW - Bio-flame retardant PY - 2022 AN - OPUS4-55840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel T1 - Wehrmedizinisches Sonderforschungsvorhaben 29K4 "Primäres Explosionstrauma": „Entwicklung und Validierung eines Körpermodells und eines Stoßwellengenerators zur Simulation der intrakorporalen Stoßwellenausbreitung nach Explosionen“ N2 - Im Rahmen dieses Vortrags wurden aktuelle Arbeiten im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. T2 - 8. KSK Symposium Rüstung 2022 CY - Altensteig/Wart, Germany DA - 13.09.2022 KW - Blast KW - Primäres Explosionstrauma KW - Einsatzkräfte KW - Polizei KW - Körpermodell PY - 2022 AN - OPUS4-55841 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Bewertung von Fallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen N2 - Bericht über die Vorgehensweise der systematischen Untersuchungen zur Entwicklung angepasster Kriterien für die Bewertung von Aufprallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen T2 - AK Prüfstellen CY - Berlin, Germany DA - 21.09.2022 KW - Fallprüfung KW - Aufprallfundament KW - Gefahrgutverpackung KW - Fallfundament KW - Mechanische Sicherheitsprüfung PY - 2022 AN - OPUS4-55842 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Bewertung von Fallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen N2 - Bericht über die Vorgehensweise der systematischen Untersuchungen zur Entwicklung angepasster Kriterien für die Bewertung von Aufprallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen T2 - ERFA Verpackungen CY - Berlin, Germany DA - 22.09.2022 KW - Fallprüfung KW - Aufprallfundament KW - Gefahrgutverpackung KW - Fallfundament KW - Mchanische Sicherheitsprüfung PY - 2022 AN - OPUS4-55843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Johann, Sergej A1 - Kadoke, Daniel A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Zehn, M. W. T1 - Damage assessment of complete, filled fibreboard boxes in regulative vertical impact tests by dropping N2 - Due to the high damping mechanical properties of fibreboard materials, corrugated fibreboard boxes are widely used as transport packages of dangerous goods. Since there is a hazard of vertical impact within the distribution system, drop tests are performed as design type tests to assess the package’s ability to withstand damage. However, there is little information in this context regarding the mechanical response of a filled fibreboard box. This work aims to propose a concept utilizing experimental drop test results by means of finite-element (FE) analyses in order to predict the damage resistance of complete, filled corrugated fibreboard boxes which are ready for transportation. T2 - 38th Danubia Adria Symposium on Advances in Experimental Mechanics CY - Poros Island, Greece DA - 20.09.2022 KW - Drop test KW - Dangerous goods packagings KW - Corrugated fibreboard box KW - Finite-element-analysis KW - Explicit transient simulation KW - Crash simulation PY - 2022 AN - OPUS4-55845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kremberg, Jan A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Fire tests of carbon tension members for lightweight constructions N2 - Vorstellung der Brandversuche im Rahmen des Projektes NeZuCa an Carbonzuggliedern für den Brückenbau. T2 - ClimateChange@FireScience CY - Berlin, Germany DA - 10.11.2022 KW - Fire tests KW - Carbon KW - Lightweight constructions KW - Fire Science PY - 2022 AN - OPUS4-56302 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hupp, Vitus A1 - Schartel, Bernhard A1 - Flothmeier, K. A1 - Hartwig, A. T1 - Adhesive Tapes in Bonded Materials Fire Risk or Protective Layer? N2 - In the recent years, more and more products in construction and automotive industry are bonded by adhesive tapes instead of mechanical fasteners but there is no sufficient understanding of how these bonded, layered materials behave in fires. Our research project gives an insight of how adhesives and substrates interact with each other in different fire scenarios and how flame retardants function in pressure sensitive adhesive (PSA) tapes. A systematic investigation on the burning behavior of PSA tapes as free-standing films, as top layers on different substrates and as sandwich-like adhesive joints was performed. The burning behavior of free-standing PSA tapes and those used as a coating was significantly improved by using phosphorus-based flame retardants. Furthermore, it was shown that, depending on tape structure and substrate, the PSA tape can lower the fire risk by acting as an intermediate protection layer in bonded materials. T2 - Fire and Polymers CY - Napa, California, USA DA - 05.06.2022 KW - Pressure Sensitive Adhesives KW - Tapes KW - Fire Behavior KW - Bonded Materials PY - 2022 AN - OPUS4-55094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seyhan, E. A1 - Ebell, Gino A1 - Jimenez, D. A1 - Chavez, J. A1 - Sanchez Alvarez, G T1 - Evaluation of SACI performance on reinforced concrete structures N2 - Surface applied corrosion inhibitors (SACI) are widely used to mitigate corrosion process of steel reinforcement in concrete. But they remain controversial as to their effectiveness and the ability to compare materials from different manufacturers and technologies. They are applied onto the surface of hardened concrete and penetrate towards steel reinforcement. This paper discusses the corrosion inhibition performances of dual-phase surface applied corrosion inhibitor and the efficiency of the corrosion inhibitor is assessed by selected testing procedures in BAM laboratories. T2 - ACHE 2022 CY - Santander, Spain DA - 20.06.2022 KW - Corrosion KW - Inhibitor PY - 2022 AN - OPUS4-55095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mensinger, M. A1 - Fischer, O. A1 - Oberhaidinger, F. A1 - Stimmelmayer, L. A1 - Ebell, Gino A1 - Babutzka, Martin T1 - Grouted joint for integral composite frame bridges suitable for hot dip galvanizing N2 - Due to the corrosion resistance of carbon steel, bridge constructions are currently protected against corrosion by applied coating systems. These coating systems need to be renewed after approximately 25 50 years. Galvanized constructions without any welding areas at the construction site could be prepared as grouted joints and can be used without any renewing for about 100 years. T2 - Intergalva 2022 CY - Rome, Italy DA - 20.06.2022 KW - Corrosion KW - Galvanized steel KW - Bridge PY - 2022 AN - OPUS4-55096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Zündgefahren durch Funken - Grundlagen und Maßnahmen zum Explosionsschutz N2 - Hersteller von Geräten für den bestimmungsgemäßen Gebrauch in explosionsfähigen Bereichen müssen, wenn sie unter die Richtlinie 2014/34/EU fallen, für das Inverkehrbringen in EU-Mitgliedsstaaten eine Konformitätsbewertung durchführen. Dazu gehört eine Zündgefahrenbewertung, bei der auch nichtelektrische Zündquellen betrachtet werden müssen, zu denen die mechanischen Schlagvorgänge gehören. Bei dieser Zündquellenart kommt es infolge eines Schlages und/oder Reibens eines Bauteils auf ein anderes zu einer Energieumwandlung. Dadurch kommt es zu einer Temperaturerhöhung an der Kontaktstelle sowie unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Reibflächen als auch die abgetrennten Partikel stellen potentielle Zündquellen explosionsfähiger Atmosphären dar. Edelstahl ist für Geräte für die Verwendung zum bestimmungsgemäßen Gebrauch im explosionsgefährdeten Bereich insbesondere in der Chemie ein wichtiger Konstruktionswerkstoff. Die Ergebnisse des Forschungsprojektes "Entwicklung normativer Anforderungen an explosionsgeschützte nichtelektrische Geräte resultierend aus der Zündfähigkeit mechanisch erzeugter Schlagfunken (NAMES)" zeigen, dass Schlagvorgänge mit Edelstählen eine erhebliche Zündgefahr von explosionsfähigen Brenngasgemischen darstellen können. Dabei bestehen jedoch mitunter deutliche Unterschiede zwischen den verschiedenen Brenngasgemischen. Besonders hohe Zündwahrscheinlichkeiten konnten bei Brenngasgemischen mit Brenngasen der IEC-Explosionsgruppe IIC beobachtet werden, die Acetylen bzw. Wasserstoff als Brenngas enthielten. Schläge im Wasserstoff/Luft-Gemisch waren dabei jedoch bedeutend zündwirksamer. In diesem Gasgemisch konnte bei niedrigen maximalen Schlagenergien bis 60 J sogar eine mitunter höhere relative Zündhäufigkeit beobachtet werden als bei Versuchen mit unlegiertem Baustahl. T2 - Ausbildung zum Explosionsschutzbeauftragten CY - Essen, Germany DA - 21.06.2022 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Zündgefahrenbewertung KW - Funkenarme Werkzeuge KW - Funkenfreie Werkzeuge PY - 2022 AN - OPUS4-55098 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard A1 - Battig, Alexander A1 - Böhning, Martin A1 - Frasca, Daniele A1 - Schulze, Dietmar A1 - Strommer, Bettina A1 - Tabaka, Weronika A1 - Wachtendorf, Volker T1 - Multifunctional Elastomer/Graphene Nanocomposites N2 - A few layer/multilayer graphene (MLG) with a specific surface area of BET=250 m2/g is proposed as an efficient multifunctional nanofiller for rubbers. The preparation method, i.e., ultrasonically-assisted solution mixing of master batches followed by two-roll milling, strongly influences the dispersion in the elastomeric matrix and is fundamental for the final properties. When homogenously dispersed, single stacks of only approximately 10 graphene sheets, with an aspect ratio of 34, work at low loadings, enabling the replacement of large amounts of carbon black (CB), an increase in efficiency, and a reduction in filler load. The appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing, gas barrier properties, electrical and thermal conductivity, as well as mechanical properties of different rubbers, as shown for chlorine-Isobutylene-Isoprene rubber (CIIR), nitrile-butadiene rubber (NBR), natural rubber (NR), and styrene-butadiene rubber (SBR). 3 phr of MLG tripled the Young’s modulus of CIIR, an effect equivalent to 20 phr of CB. The stronger interactions between MLG and NR or SBR also resulted in a reduction in the elongation at break by 20% and 50%, respectively, while the same parameter was hardly changed for CIIR/MLG and NBR/MLG. CIIR/MLG and NBR/MLG were stiffer but just as defomable than CIIR and NBR. The strong reinforcing effect of 3 phr MLG was confirmed by the increase of greater than 10 Shore A in hardness. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards flammability, the latter shown by the reduction in heat release rate in the cone calorimeter. We investigated MLG also as a synergist for reducing the aluminium trihydrate loading in flame retardant hydrogenated acrylonitrile-butadiene (HNBR), polybutadiene chloroprene (BR/CR), and chlorosulfonated polyethylene rubber(CSM). The higher the nanofiller concentration is, the greater the improvement in the properties. For instance, the permeability decreased by 30% at 3 phr of MLG, 50% at 5 phr and 60% at 10 phr, respectively. Moreover, the MLG nanocomposites improve stability of mechanical properties against the effects of weathering. In key experiments an increase in UV-absorption and a pronounced radical scavenging were proved as stabilizing mechanisms. In a nutshell, MLG is an efficient multifunctional nanofiller ready to be used for innovative rubber development. T2 - 19th European Polymer Congress, EPF 2022 CY - Prague, Czech Republic DA - 26.06.2022 KW - Graphene KW - Nanocomposite KW - Rubber KW - Elastomer PY - 2022 AN - OPUS4-55196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man T1 - Investigation of temperature effects on ultrasonic velocity in a prestressed concrete bridge model N2 - Ultrasonic measurements have recently been applied in the context of structural health monitoring in civil engineering. The ultrasonic method is very sensitive to environmental conditions and material property changes, which might be caused by prestress losses and loading effects on the bridge. However, it remains a challenge to identify the damage mechanisms causing structural property changes from the above-mentioned factors influencing ultrasonics. The focus of this contribution is to investigate the correlation between ultrasonic velocities and temperature by the coda wave interferometry (CWI) analysis. Long-term monitoring of a prestressed concrete bridge model under field conditions was carried out to observe the effect of temperature. The homogeneous change in concrete caused by temperature was revealed by applying the CWI method. The threshold value of the best correlation coefficients for the linear regression of temperature and ultrasonic velocity changes was also studied. Experimental assessment will provide a ratio for temperature correction to evaluate the prestressing force decrease and its consequences on crack opening or extension. T2 - Tagung EWSHM2022 CY - Palermo, Italy DA - 04.07.2022 KW - Ultrasonic velocity KW - Coda wave interferometry KW - Temperature correction KW - Prestressing force KW - Bridge monitoring PY - 2022 AN - OPUS4-55290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Wave propagation from hammer, vibrator and railway excitation – theoretical and measured attenuation in space and frequency domain N2 - The attenuation of wave amplitudes is ruled by the planar, cylindrical or spher-ical geometry of the wave front (the geometric or power-law attenuation) but also by the damping of the soil (an exponential attenuation). Several low- and high-frequency filter effects are derived for the layering and the damping of the soil, for the moving static and the distributed train loads and for a homoge-neous or randomly heterogeneous soil. Measurements of hammer- and train-induced vibrations at five sites have been analysed for these attenuation and filter effects. The measured attenuation with distance can be discribed by gen-eralised power laws and some reasons will be discussed. The theoretical filter effects can well be found in the measurements. T2 - 10th Wave Mechanics and Vibration Conference (WMVC)nce CY - Lisbon, Potugal DA - 04.07.2022 KW - Hammer impact KW - Train passage KW - Layered soil KW - Attenuation KW - Filter effects KW - Randomly heterogeneous soil KW - Scattering PY - 2022 AN - OPUS4-55246 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Häßler, Dustin T1 - Reaktive Brandschutzsysteme N2 - Die Präsentation gibt einen Überblick zum Anwendungsbereich und den -grenzen von reaktiven Brandschutzsystemen. Ferner werden Forschungsergebnisse der BAM vorgestellt. T2 - Stahlbau-Kalender-Tag 2022 CY - Stuttgart, Germany DA - 24.06.2022 KW - Reaktive Brandschutzsysteme KW - Feuerwiderstand KW - Stahlbau KW - Brandversuche KW - Dauerhaftigkeit PY - 2022 AN - OPUS4-55250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Königsbauer, Korbinian A1 - Schaller, M.-B. A1 - Nöther, N. A1 - Wosniok, Aleksander T1 - Entwicklung eines praxistauglichen auf POF basierenden Messsystems mittels digitaler I-OFDR zur Dehnungsdetektion N2 - Es wird ein faseroptisches Messsystem vorgestellt, welches auf Basis der Rayleigh-Rückstreumessung eine ortsauflösende Detektion von signifikant großen Dehnungen bei Bauvorhaben im von Anwendern geforderten Größenordnungsbereich von 3 % bis 10 % ermöglicht. Mit dem Verfahren der digitalen inkohärenten optischen Frequenzbereichsreflek-tometrie (I-OFDR) werden materialspezifische Vorteile robuster perfluorierter polymeroptischer Fasern (PF-POF) erschlossen. Für den angestrebten industriellen Einsatz für die Zustandsüberwachung im Bereich des Tunnel- und Spezialtiefbaus soll die spezifische Rückstreuzunahme in der PF-POF hochauflösend gemessen werden. In diesem Vortrag wird gezeigt, dass sich in ersten Projektergebnissen das digitale I-OFDR für eine Dehnungsdetektion von bis zu 10% eignet. T2 - 21. ITG/GMA-Fachtagung CY - Nuremberg, Germany DA - 10.05.2022 KW - I-OFDR KW - Structure health monitoring KW - Dehnungsdetektion KW - Reyleigh-Rückstreumessung PY - 2022 AN - OPUS4-56717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Königsbauer, Korbinian A1 - Schaller, M.-B. A1 - Nöther, N. A1 - Wosniok, Aleksander T1 - Distributed POF sensors for structural health monitoring in civil construction applications N2 - In this presentation, a cost-efficient distributed fiber optic measurement system based on Rayleigh scattering is shown. The distributed digital incoherent optical frequency domain reflectometry (I-OFDR) method is devel-oped for detection of significantly large strain in the range from 3 % up to 10 % as required by end users. For this purpose, a vector network analyzer used in the I-OFDR is replaced by a compact and costeffective digital data acquisition system. This digital emitting/receiving unit enables the recording of the complex transfer function carrying information about the local deformations along the entire sensing fiber. T2 - POF 2022 The 30th International Conference on Plastic Optical Fibers CY - Bilbao, Spain DA - 26.09.2022 KW - I-OFDR KW - Perfluorinated polymer optical fiber (PF-POF) KW - Strain detection KW - Structural health monitoring. PY - 2022 AN - OPUS4-56714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Challenges of vibration prediction – realistic irregularities, the scattering of axle pulses, and the tunnel-surface reduction N2 - A prediction software has been developed by BAM. The following topics have still be solved. A realistic irregularity spectrum can be derived from axle-box measurements. It agrees wel with the spectrum used for the high-speed 2 project in the United Kingdom. In addition, the scattering of axle pulses should be included. This mid-frequency component can also be found in the HS2 procedure. Finally, the reduction in case of a tunnel line compared to a surface line should be included. Some measurement results of BAM, HS2 and other institutes show a certain mid-frequency reduction. This is due to the load distribution of the tunnel which yields softer axle pulses and the scattered axle impulses are reduced. T2 - ISO/TC 108/SC 2/WG 8 Working group Ground-borne noise and vibration from rail systems CY - London, UK DA - 21.11.2022 KW - Ground vibration KW - Railway trafiic KW - Prediction KW - Irregularities KW - Axle pulses KW - Tunnel line KW - Surface line PY - 2022 AN - OPUS4-56738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Role of the Authority in the Approval Process of Packaging N2 - In Germany, BAM is the competent authority in the field of dangerous goods transport. The international dangerous goods transportation rules are presented and their adaptation into German law is described. BAM is responsible for dangerous goods packaging testing, manufacturer surveillance, packaging approvals and inspection of IBC and provides “Gefahrgutregeln” (GGR) to define the processes, e.g. of dangerous goods packagings approvals and surveillance.” T2 - Sino-German Workshop on Dangerous Goods Packaging CY - Online meeting DA - 18.11.2022 KW - Gefahrgutverpackungen KW - Zulassung KW - ADR PY - 2022 AN - OPUS4-56754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasch, Thomas A1 - Thomas, Brock A1 - Hesse, Olaf T1 - Assessment Criteria to Evaluate Test Results on Compatibility of Nonmetallic Materials for Oxygen Service Based on BAM’s Safety Philosophy N2 - The general requirement, that nonmetallic materials for oxygen service must be tested and found suitable for their intended use in plants and components is the current state of technical safety. However, numerous requests of manufacturers, sales offices, and users show, that there is still a strong need for information on how these materials are tested and evaluated. Based on more than 60 years of expertise, this paper provides background information on BAM’s test approach. It explains why BAM applies additional assessment criteria on nonmetallic materials for certain use conditions. Hence, the test schedule as well as the final evaluation shall reflect the practical application in a more customer-related way in combination with a higher safety level. That is the demand of BAM’s safety philosophy. T2 - 15th international symposium on flammability and sensitivity of materials in oxygen-enriched atmospheres CY - Online meeting DA - 03.05.2022 KW - Oxygen compatibility KW - Background information on test approaches KW - Evaluation of test results KW - Assessment criteria KW - BAM’s safety philosophy PY - 2022 AN - OPUS4-54887 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liebner, Christian A1 - Patzelt, Anne-Katrin A1 - Krentel, Daniel T1 - BAM Testgelände Technische Sicherheit (TTS) N2 - Die Präsentation zeigt in Bild und Video die Möglichkeiten auf dem BAM TTS zur Durchführung von Versuchen unterschiedlicher Gefährlichkeitsstufen auf. Sie wendet sich an potentielle künftige Kooperationspartner aus dem Bereich der zivilen Sicherheitsforschung (Polizeibehörden, Feuerwehr, THW, andere Forschungseinrichtungen), um deren Forschungsbedarf mit den an der BAM vorhandenen Testmöglichkeiten abzugleichen und so ebenfalls dem Aufbau von überflüssigen konkurrierenden Parallelstrukturen an anderen Forschungseinrichtungen vorzubeugen. T2 - ForAn Anwendertreffen zum BMBF-Innovationsforum "Zivile Sicherheitsforschung" CY - Berlin, Germany DA - 02.05.2022 KW - Zivile Sicherheitsforschung KW - Großversuche KW - Testgelände PY - 2022 AN - OPUS4-54847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Yevtushenko, Oleksandra A1 - Le, Quynh Hoa A1 - Bettge, Dirk T1 - Corrosion Effects on Materials Considered for CC(U)S Applications N2 - Commercially available carbon steels are suitable for compression and pipelines as long as moisture content and impurities are limited. (water 50 to 100 ppmv, SO2 and NO2 ca. 100 ppmv) Corrosion rates increase with increasing water content. (0.2 – 20 mm/a) Condensation of acids and therefore droplet formation is always possible, even at low water contents. A low SO2 content within the CO2-stream might be more important than a low water content. Cr13-steels showed a general susceptibility to shallow pitting and pitting. So, they seem to be not suitable for CCUS applications. Low alloyed steels showed better corrosion behavior (predictable uniform corrosion). For direct contact with saline aquifer fluids only high alloyed steels shall be used. T2 - EFC Webinar CY - Online Meeting (Chongqing, China) DA - 18.05.2022 KW - Corrosion KW - CO2 quality KW - CO2 KW - CCS KW - CCU KW - Pipeline PY - 2022 AN - OPUS4-54854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Elastische Elemente in der Emission, Transmission und Immission von Bahnerschütterungen N2 - Dieser Vortrag präsentiert einige Prinzipien und einige Beispiele zur Minderung von Eisenbahnerschütterungen. Die Prinzipien unterscheiden sich für die Minderungsmaßnahmen im Gleis, im Boden und bei Gebäuden. Kraftübertragungsfunktionen isolierter und nicht isolierter Gleissysteme, reflektierte und durchgelassene Wellenamplituden bei gefüllten Bodenschlitzen und die Übertragung der Freifeldschwingungen ins Gebäude werden analysiert. Bei den einfachen Gleismodellen muss der richtige Anteil der unabgefederte Fahrzeugmasse zum eindimensionalen Gleismodell hinzugefügt werden. Der Minderungseffekt eines gefüllten Bodenschlitzes ist von der Steifigkeit und nicht von der Impedanz des Schichtmaterials bestimmt. Bei einer elastischen Gebäudelagerung muss die Minderungswirkung mit der richtigen Boden- (Fundament-) Steifigkeit berechnet werden, und das abgeminderte Gebäudeverhalten hängt wesentlich von der effektiven Gebäudemasse ab, die mit zunehmender Frequenz deutlich kleiner als die starre Gebäudemasse ist. T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Bludenz, Austria DA - 17.5.2022 KW - Erschütterungsminderung KW - Bahngleis KW - Bodenschlitz KW - Gebäudelagerung KW - Elastische Elemente PY - 2022 AN - OPUS4-54916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Hüllmann, Dino A1 - Winkler, Nicolas P. A1 - Schugardt, Jan T1 - Remote Drone-to-Drone Gas Sensing: A Feasibility Study N2 - Remote gas sensors mounted on mobile robots enable the mapping of gas distributions in large or poorly accessible areas. A challenging task however, is the generation of three-dimensional distribution maps from these spatially sparse gas measurements. To obtain high-quality reconstructions, the choice of optimal measuring poses is of great importance. Remote gas sensors, that are commonly used in Robot Assisted Gas Tomography (RAGT), require reflecting surfaces within the sensor’s range, limiting the possible sensing geometries, regardless of whether the robots are ground-based or airborne. By combining ground and aerial robots into a heterogeneous swarm whose agents are equipped with reflectors and remote gas sensors, remote inter-robot gas measurements become available, taking RAGT to the next dimension – releasing those constraints. In this paper, we demonstrate the feasibility of drone-to-drone measurements under realistic conditions and highlight the resulting opportunities. T2 - 19th International Symposium on Olfaction and Electronic Nose CY - Aveiro, Portugal DA - 29.05.2022 KW - Aerial robot KW - TDLAS KW - Inter-robot measurements KW - Gas tomography KW - Plume PY - 2022 AN - OPUS4-54927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Sandra F. A1 - Schartel, Bernhard A1 - Wang, Y.-Z. A1 - Bocz, K. T1 - black as hell, strong as death and sweet as love - pyrolyzed waste materials and cyclodextrins as effective filler in flame retarded epoxy composites N2 - Renewable alternatives for common thermoset resins are demanded to go for sustainability. The objective is to create a flame retarded epoxy resin from a commercial bio epoxy resin with halogen free inorganic and organic flame retardants, respectively. Alumina trihydrate, aluminum diethyl phosphinate, a DOPO-based phosphonamidate and ammonium polyphosphate seem to have promising performances. Properties are enhanced with different bio fillers: pyrolyzed cocoa shells and plant waste (provided by Otto A. Müller Recycling GmbH, thanks!), short fibers and nonwovens of the natural fiber kenaf, hydroxypropyl-ß-cyclodextrin and sulfobutylether-ß-cyclodextrin. Fire performance is investigated by cone calorimeter examinations, LOI and UL-94 ratings. Thermal analysis is given by TG-FTIR and DSC measurements. Combinations of flame retardants and bio-fillers lead to reduced PHRR and THR, reach V0 in UL-94 and have a significant increase in LOI of up to 37 vol.-%. 10 % ammonium polyphosphate with 10 % pyrolyzed cocoa shell performs best, builds a magnificent protective layer, and shows good intumescence. T2 - 3rd international conference on eco-friendly flame retardant additives and materials CY - Alès, France DA - 17.05.2022 KW - Epoxy resin KW - Flame retardant KW - Kenaf fiber KW - Pyrolyzed plant waste KW - Cyclodextrin PY - 2022 AN - OPUS4-54928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Charakterisierung von Salzbeton und alkali-aktivierten Material basierend auf der Schallemissionsanalyse N2 - Nach einer kurzen Einführung in die Schallemissionsprüfung und -Analyse wird ein Versuchsstand vorgestellt, der im Rahmen des Themenfeldprojektes Seal Waste Safe installiert wurde. Schwerpunkt des Vortrages sind die Schallemissionsmessungen an einem 150 l Demonstrator aus Salzbeton und einem weiteren aus alkali-aktiviertem Material. Neben der konventionellen Schallemissionsanaylse mit Aktivitäts- und Intensitätsparametern der Zeitsignale, werden auch frequenzbasierte Parameter zur Analyse andiskutiert. N2 - After a brief introduction to acoustic emission testing and analysis, an experimental test setup is presented, which was part of the Seal Waste Safe project (internal BAM project 2019-2022). Herein, the acoustic emission measurements of a 150 l demonstrator made of salt concrete and another one made of alkali-activated material are focused. In addition to the conventional acoustic emission analysis regarding the activity and intensity parameters of the detected time signals, also frequency-based parameters were discussed for analysis. T2 - Dauerhafte Verschlussbauwerke für Endlager CY - Online meeting DA - 14.2.2022 KW - Acoustic Emission KW - Schallemission KW - Salzbeton KW - Alkali aktiviertes Material KW - Geopolymer PY - 2022 AN - OPUS4-54937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Grundlagen der Korrosion N2 - Darstellung der Grundlagen der elektrochemischen Korrosion von metallenen Werkstoffen im Bauwesen. Dabei liegt das Hauptaugenmerk auf dem Zusammenhang zwischen Energieaufwand für den Herstellungsprozess und daraus resultierendem thermodynamisch instabilen Zustand und Korrosionsneigung. Der Einfluss der Deckschicht- Oxidschichtbildung wird ebenfalls behandelt. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Elektrochemische Messungen N2 - Elektrochemische Messungen könne, richtig angewandt, dazu dienen ein Korrosionssystem ausreichend gut zu beschreiben. Im Bauwesen, speziell bei Stahl in Beton, ist es jedoch ohne Kenntnis der korrodierenden Flächen oft nur möglich zwischen aktiv korrodierenden Bereichen und passiven, als Kathode wirksamen, Bereichen zu differenzieren. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Potentialfeldmessung KW - Korrosion PY - 2022 AN - OPUS4-54869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Merkblatt B 03 der DGZfP - Ausgabe April 2014 N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbedingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanierungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54870 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino T1 - Erörterung des Messprotoklls N2 - Das für die Potentialfeldmessung in der neusten Ausgabe des Merkblattes B03 der DGZfP erarbeitete Messprotokoll berücksichtigt sowohl en Einsatz, von Stab-, Einrad- oder Vierradelektroden. In diesem Vortrag wird auf alle varianten des Gegenmessen von Bezugselektroden im Einsatz eingegangen, ebenso wie auf das Erfassen der notwendigen Randparameter. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Mögliche Fehlerquellen in der Praxis N2 - Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. Bei der Durchführung dieser Messung gibt es jedoch messtechnikspezifische Fehlerquellen und äußere Einflüsse aus dem zu untersuchenden Bauwerk die eine Interpretation der Messergebnisse signifikant beeinflussen können. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Spannbetonbauwerke - Von der Initiierung zum Schaden N2 - Wasserstoffinduzierte Spannungsrisskorrosion an hochfesten und hochempfindlichen Spannstählen führt an bestehenden Brückenbauwerken nach Jahren der Rissinitiierung zu Trag- und Standsicherheitsverlusten. Anhand des Beispiels der Brücke am Altstädter Bahnhof gibt es eine bauartbedingte Schadensinitiierung die über den gesamten Spannkanalquerschnitt zu Spannungsrisskorrosion führen kann. T2 - AK-Sitzung Korrosionsschutz im konstruktiven Ingenieurbau CY - Online meeting DA - 12.05.2022 KW - Spannungsrisskorrosion KW - Korrosion PY - 2022 AN - OPUS4-54874 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Schartel, Bernhard A1 - Lin, Xuebao A1 - Tan, Yi A1 - Schoch, R. A1 - Lang, M. A1 - Tröppner, O. A1 - Bosse, M. T1 - Untersuchung der Witterungsbeständigkeit komplexer Funktionalitäten von Polymerwerkstoffen durch künstliche Bewitterung: Flammschutz N2 - In den letzten Jahrzehnten wurde die Degradation der polymeren Matrix von flammgeschützten Polymeren eingehend untersucht. Erst in den letzten Jahren jedoch hat sich die Frage der Lebensdauer der Funktionalität des Flammschutzes selbst als wichtige Fragestellung herauskristallisiert, z.B. bei Kabeln. Deshalb sollte diese Fragestellung durch systematisch-variierte künstliche Klima- und Bewitterungstests an flammgeschützten Polymerwerkstoffen untersucht werden T2 - 50. Jahrestagung der Gesellschaft für Umweltsimulation (GUS) CY - Online meeting DA - 23.03.2022 KW - Flammschutz KW - Witterungsbeständigkeit KW - Langzeitbeständigkeit KW - UV KW - E&E PY - 2022 AN - OPUS4-54541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph T1 - Evaluation of Corrosion Resistance of Metallic Materials in Geothermal Applications N2 - Evaluation of corrosion resistance of metallic materials is essential to assure safe and reliable operation of geothermal sites. One need to be aware that corrosion is not a material's but a system property, determined by medium, material and construction aspects. Various corrosion types have to be evaluated. Conditions in laboratory shall reflect on-site reality. Depending on brine composition and temperature suitability of metallic materials can be ranked. Most important outcome of the research is that highly saline geothermal brines require high alloyed materials, for safe long-term operation. T2 - Geothermal Essentials - Moving Geothermal Forward in Canada: Scaling and Corrosion (Surface Facilities) CY - Online Webinar DA - 16.03.2022 KW - Corrosion KW - Geothermal KW - Steel PY - 2022 AN - OPUS4-54482 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Aristia, G. A1 - Le, Quynh Hoa T1 - Integrated Coating System for Corrosion Protection of Carbon Steel in Artificial Geothermal Brine N2 - Corrosive geothermal brines are a major challenge to geothermal power-plants. For cost reasons, plant designers prefer to use carbon and low alloyed steels, which are susceptible to uniform and localized corrosion when exposed to geothermal brines having acidic and saline properties. To solve such problem, coatings or inhibitors would be a protective solution as an alternative to the use of high alloyed materials. This study investigated a coating system consisting of polyaniline/silicon dioxide based on resources locally available in Indonesia. Protection against corrosion of carbon steel was shown by long-term (28 day) exposure and electrochemical tests of coated carbon steels, performed in an artificial acidic and saline geothermal brine, comparable to the conditions encountered at a site in Indonesia. Therefore, an integrated coating system is proposed for corrosion protection, combining the electrochemical functionality of polyaniline and the physical advantages of silica. T2 - AMPP International Corrosion Conference 2022 CY - San Antonio, TX, USA DA - 08.03.2022 KW - Geothermal KW - Corrosion KW - Coating KW - Polyaniline KW - Silicon dioxide PY - 2022 AN - OPUS4-54452 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Zerstörungsfreie Prüfung von Fundamenten vor der Wiedernutzung N2 - Für die Qualitätssicherung von neuen Fundamenten steht eine Reihe von zerstörungsfreien Prüfverfahren zur Verfügung. Das Portfolio reicht von der einfachen Hammerschlagmethode („Pfahlintegritätsprüfung“) bis zu aufwändigen Ultraschallverfahren für meterstarke Fundamentplatten. Aber funktionieren die Verfahren auch im Bestand? Lassen sich die für Wieder-, Um- und Weiternutzung notwendigen Daten erfassen? Und wie werden die zerstörungsfreien Prüfverfahren erfolgreich in Untersuchungskonzepte integriert? Dies wird vor allem am Beispiel der Fundamente von Freileitungsmasten diskutiert. T2 - RWTH Forum Geotechnik CY - Online meeting DA - 20.1.2022 KW - Fundamente KW - Wiedernutzung KW - Zerstörungsfreie Prüfung KW - Parallelseismik KW - Pfahlgründung PY - 2022 AN - OPUS4-54236 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - Update nach 10 Jahren Bewitterung - Langzeitkorrosionsverhalten nichtrostender Stähle in maritimer Atmosphäre N2 - Durch Fortführung der Untersuchungen aus einem Forschungsvorhaben wurden neun verschiedene Stahllegierungen unter maritimen Umgebungsbedingungen über zehn Jahre ausgelagert und deren Korrosionsverhalten untereinander verglichen und bewertet. Anhand der Ergebnisse der Auslagerungsprüfungen konnten Rückschlüsse auf die Einflüsse der Legierungszusammensetzung, der Oberfächenausführung und der Auslagerungszeit unter maritimen Auslagerungsbedingungen gewonnen werden. Die Proben der drei untersuchten Duplexwerkstoffe zeigten über den Auslagerungszeitraum von zehn Jahren sowohl mit als auch ohne Spaltgeometrie die beste Korrosionsbeständigkeit. Ebenso konnte der molybdänlegierte Ferrit 1.4521 eine vergleichbar gute Korrosonsbeständigkeit erzielen, wie die klassischen austenitischen Werkstoffe 1.4301 und 1.4404. T2 - Korrosionsschutz in der maritimen Technik 2022 CY - Online meeting DA - 27.01.2022 KW - Auslagerungsversuche KW - Korrosionsschutz KW - Korrosion KW - Nichtrostende Stähle PY - 2022 AN - OPUS4-54276 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Corrosion of Steel in Concrete and Corrosion Behavior of Stainless Steel N2 - In order to obtain a statement on the corrosion resistance of stainless steel against pitting corrosion, a well-tested measuring arrangement is required. For this purpose, the so-called ECISS test can be used to determine the critical chloride content. This makes it possible to assess the corrosion resistance of various stainless steels that have different chromium contents. T2 - ISO-TC17-SC16-WG13 Expertensitzung CY - Online meeting DA - 11.01.2022 KW - Corrosion KW - Lochkorrosion KW - Chloride induced corrosion KW - Concrete KW - Stainless steel PY - 2022 AN - OPUS4-54239 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Hüllmann, Dino A1 - Winkler, Nicolas P. A1 - Kohlhoff, Harald A1 - Bartholmai, Matthias A1 - Hirschberger, Paul A1 - Bennetts, V. H. A1 - Lilienthal, A. J. T1 - Aerial Robot Olfaction - An Overview of Research @BAM N2 - This presentation gives an introduction to the gas-sensitive aerial robots developed at BAM, including various application examples in the field of mobile robot olfaction: gas source localization, gas distribution mapping, and trial following. T2 - The 6th Meeting of the Investigation Committee on Measurement of Odors and Applications of Their Psychological/Physiological Effects CY - Online meeting DA - 21.01.2022 KW - Mobile Robot Olfaction KW - Gas Tomography KW - Tunable Diode Laser Absorption Spectroscopy (TDLAS) KW - Gas Source Localization KW - Gas Distribution Mapping KW - Trial Following PY - 2022 AN - OPUS4-54241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Die Berechnung der Einfügedämmung bei Schienenfahrwegen – die Impedanzmethode mit einem Freiheitsgrad N2 - Mit dieser Methode kann man die Einfügedämmung eines Schienenstützpunkts/einer Schwelle korrekt berechnen. Sie gilt in ihrer ursprünglichen Form für eine Unterschottermatte in einem Tunnel T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Online meeting DA - 20.1.2022 KW - Impedanzmethode KW - Elastische Elemente KW - Schienenfahrweg PY - 2022 AN - OPUS4-54243 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Monitoring von Strukturverhalten mittels integrierter verteilter faseroptischer Sensorik - Verteilte akustische Sensorik (DAS) N2 - Die verteilte faseroptische akustische Sensorik (DAS) wird vorgestellt, hinsichtlich ihrer Leistungsfähigkeit beschrieben und verschiedenste Anwendungsfelder, z.B. für das Zustandsmonitoring oder für seismische Messungen, beispielhaft gezeigt. Zudem werden mögliche Anwendungsfelder von DAS für den Kontext Kerntechnische Entsorgung (KTE) und Rückbau aufgezeigt. T2 - Online-Workshop „Dauerhafte Verschlussbauwerke für Endlager“ CY - Online meeting DA - 14.02.2022 KW - Verteilte faseroptische Sensorik KW - Verteilte akustische Sensorik KW - DAS KW - KTE KW - Monitoring Endlager PY - 2022 AN - OPUS4-54348 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Zündgefahren durch Funken – Grundlagen und Maßnahmen zum Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA22-00800) ; Außeninstitut der RWTH Aachen CY - Lübeck, Germany DA - 09.08.2022 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanischer Explosionsschutz KW - Nichtelektrischer Explosionsschutz PY - 2022 AN - OPUS4-55483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst A1 - Hindersmann, I. A1 - Sodeikat, C. A1 - Groschup, R. T1 - Monitoring of a German Road Bridge Using Embedded Ultrasonic Transducers and Coda Waves N2 - The ‘G¨anstorbr¨ucke’ bridge between the cities of Ulm and Neu-Ulm is one of the best-monitored bridges all over Germany. In addition to an already active bride monitoring system, we have equipped the bridge with 30 ultrasonic transducers to explore the monitoring possibilities at an in-service large-scale reinforced concrete structure with continuous active ultrasonic measurements. The monitoring system is based on the detection of small changes in the entire signal, especially the multiply scattered parts of the recording, the so-called coda. Applying Coda Wave Interferometry (CWI), subtle changes in the signal can be detected and related to changing velocities in the area between source and receiver. A comparison of the results from coda wave interferometry with the strain measurements of the permanent monitoring system shows a correlation between strain measurements and CWI results. We discuss the challenges of changing environmental conditions, pose for interpretation of the results, and highlight the advantages of embedded versus externally attached ultrasonic transducers in permanent bridge monitoring, especially when coda wave interferometry is applied. T2 - EWSHM 2022 CY - Palermo, Italy DA - 04.07.2022 KW - Bridge monitoring KW - Ultrasound KW - Embedded sensors KW - Coda wave interferometry PY - 2022 AN - OPUS4-55383 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Bernauer, F. A1 - Igel, H. A1 - Hadziioannou, C. T1 - Real time bridge monitoring using ultrasonic techniques combined with six component (6-c) measurements N2 - This study aims to develop a real-time monitoring method for the structural performance by ultrasonic testing in combination with six-component (6-C) translation and rotation measurements. So far, the recordings of the velocity and acceleration response in the translation direction have been used to obtain the eigenfrequencies of structures. Recently, measurement of rotation has been used to fully characterize the dynamic behavior of structures. In this research, 6-C sensors consisting of a three-component rotational seismometer and a three-component broadband seismometer are evaluated for their suitability for bridge monitoring. Since changes in environmental conditions such as temperature during vibration recordings affect the structural evaluation results, cross-correlation function is applied here to the 6-C ambient vibration signals to reconstruct the wave propagation on the one hand, and coda wave interferometry (CWI) is applied to obtain the internal velocity variation from waveforms on the other hand. In field tests on a large-scale prestressed concrete bridge model, it was verified whether the prestress loss can also be determined in presence of temperature effects. For this purpose, measurements were performed in two scales, ultrasonic and output-only vibration measurements. The change in structural properties due to the prestress loss should be detected by the pulse velocity change. The results demonstrate both the performance and advantages of ultrasonic techniques and the capabilities of 6-C sensors. Thus, the application of CWI to wave signals can contribute comprehensively to bridge monitoring. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - 6-C vibration signals KW - Coda wave interferometry KW - Cross-correlation function KW - Prestressed bridge KW - Structural health monitoring KW - Ultrasonic PY - 2022 AN - OPUS4-55646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Taffe, A. A1 - Braml, T. T1 - On the Treatment of Measurement Uncertainty in Stochastic Modeling N2 - Measurement uncertainty calculations in stochastic moddeling of time-independent, NDT-based random variables to be used in refined assessment of existing structures T2 - International Probabilistic Workshop 2022 (IPW2022) CY - Stellenbosch, South Africa DA - 08.09.2022 KW - Reliability KW - Assessment KW - Existing structures KW - Measurement uncertainty PY - 2022 AN - OPUS4-55657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Schönsee, Eric A1 - Jeyifous, Olubunmi Anthony A1 - Mezhov, Alexander A1 - Hüsken, Götz T1 - Introduction of a monitoring system for Bingham fluids in additive manufacturing with concrete N2 - Freeform additive manufacturing of concrete structures is a rising technology in civil engineering with several fascinating advantages. Nonetheless, to ensure reliability and structural integrity, standards and quality control are required in the future to bring this technology into the market. As the concrete is manufactured continuously, continuous quality control of the printing process is also required, i.e. comprehensive process monitoring. At BAM, a test rig will be installed, enabling the printing of concrete structures with a maximum size of 2 m x 1 m x 1 m (l x w x h). Here, process monitoring is the focus of the test rig. In this study, we show the results of the first pump tests, including the measurement of several parameters such as temperature and pressure along the supply system, i.e. from the concrete pump to the printer head. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Additive manufacturing of concrete KW - Process monitoring KW - Non-destructive testing KW - Bingham fluid PY - 2022 AN - OPUS4-55637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Stoljarova, A. A1 - Regenspurg, S. T1 - Influence of brine components on materials performance in geothermal applications N2 - Significant Cu-deposition and ‑precipitation only occurred in combination with carbon steel. High-alloyed materials prevent the disturbing Cu-agglomeration. Pb-deposition and ‑precipitation only occurred in combination with carbon steel. No negative Pb-effect could be observed in combination with high-alloyed steels. High alloyed corrosion resistant alloys are suitable and shall be chosen for future design of the piping system, either in massive or in cladded form, if formation of crevices with non-metallic materials can be excluded! T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Corrosion KW - Geothermal KW - Copper PY - 2022 AN - OPUS4-55624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Hicke, Konstantin A1 - Bernauer, F. A1 - Igel, H. A1 - Hadziioannou, C. T1 - Multi-Sensor measurements on a large-scale bridge model N2 - This contribution introduces an investigation of a large-scale prestressed concrete bridge model (“BLEIB” structure at the BAM-TTS open air test site) by means of on-site cooperative measurements. This bridge has an external post-tensioning system and has been instrumented with the ultrasonic transducers, temperature sensors and optical fibers for Distributed Acoustic Sensing (DAS). Our experiment was designed to test the suitability of the novel 6C sensors developed within the framework of the GIOTTO project – the IMU50. The IMU50 sensor enables vibration measurements in translation along three axes and rotation around three axes. The geophone sensors were considered for complementary measurements of vertical velocity response. In the experiment, several perturbations were achieved by controlling the external influence factors such as loading and prestressing changes. The aim of the integrated measurement strategy was to fully observe the results of the condition change and to verify the effectiveness of multiple sensors for bridge monitoring. T2 - 5. Brückenkolloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Concrete KW - Bridge KW - Monitoring KW - Rotation KW - Distributed acoustic sensing PY - 2022 AN - OPUS4-55626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Hille, Falk A1 - Hofmann, Detlev A1 - Kind, Thomas T1 - Überwachung der Brücke Altstädter Bahnhof, Branden-burg./H. N2 - Die B1 Brücke am Altstädter Bahnhof in Brandenburg an der Havel wurde im Dezember 2019 aufgrund von während einer turnusmäßigen Inspektion entdeckten Rissen und Hohlstellen entlang der vorgespannten Längsträger gesperrt und im Mai 2021 abgebrochen. In der Zwischenzeit wurde die Brücke detailliert überwacht. Vor dem Abriss wurden zudem umfangreiche Untersuchungen zur Bestandsaufnahme und Schadensanalyse sowie Tests moderner Sensorik vorgenommen. Dabei konnte sowohl die richtige, zuvor nicht sicher bekannte Anzahl von Spanngliedern in den Querträgern sicher ermittelt werden als auch durch moderne Varianten der Schwingungsmessungen und der faseroptischen Sensorik zusätzliche Kenntnisse püber das Bauwerksverhalten ermittelt werden . In dem Beitrag werden die Verfahren mit ihren Möglichkeiten und Grenzen vorgestellt, die Ergebnissee an der Brücke in Brandenburg erläutert und zukünftige Einsatzmöglichkeiten diskutiert. T2 - 5. Brückenkolloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Monitoring KW - Brücke KW - Radar KW - Vibration KW - Faseroptik PY - 2022 AN - OPUS4-55628 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Schmidt, Sebastian A1 - Steinbock, Oliver T1 - B1 - Brücke am Altstädter Bahnhof in Brandenburg an der Havel - Detektion von Spanndrahtbrüchen mit Schallemissionsanalyse N2 - Bei einer turnusmäßigen Inspektion der B1 Brücke am Altstädter Bahnhof in Brandenburg an der Havel wurden im Dezember 2019 Risse und Hohlstellen entlang der Längsträger festgestellt. Als Ursache wurde das Versagen eines signifikanten Anteils der Spanndrähte der konzentrierten Spannglieder vermutet. Die Brücke wurde umgehend für den Verkehr gesperrt und nach weiteren, umfassenden Untersuchungen im Mai 2021 abgebrochen. Um die Sicherheit des unter der Brücke geführten Verkehrs zu gewährleisten, wurde die Brücke unter anderem mit einem Schallemissionsmesssystem überwacht. Mit diesem Verfahren ist es möglich, Spanndrahtbrüche zuverlässig zu detektieren und zu lokalisieren. In dem gut einjährigen Überwachungszeitraum wurden mehr als einhundert Spanndrahtbrüche detektiert, die in einigen Bereichen der Brücke besonders konzentriert auftraten. Vor dem Abbruch der Brücke war es möglich, den Nachweis der Detektion von Spanndrahtbrüchen mit der Schallemissionsanalyse und ihre Ortungsgenauigkeit anhand von künstlich erzeugten Drahtbrüchen zu validieren. Weiterhin konnte das sichtbare Schadensbild, Längsrisse und Hohlstellen über den Spannkanälen, auf die lokale Schädigung der Spanndrähte zurückgeführt werden. Derzeit wird ein Merkblatt erarbeitet, in dem die Erfahrungen in der bisherigen Anwendung der Schallemissionsanalyse zum Monitoring von Spanndrahtbrüchen zusammengefasst werden. In diesem Beitrag werden die Grundlagen der Schallemissionsanalyse und die Ergebnisse der Validierungsversuche an der Brücke in Brandenburg dargestellt. Weiterhin werden die Vorteile und Grenzen der Brückenüberwachung mittels Schallemissionsanalyse sowie Maßnahmen zur Sicherstellung der Qualität und der Zuverlässigkeit diskutiert. T2 - 5. Brückenkolloquium CY - Esslingen, Germany DA - 05.09.2022 KW - Spannbetonbrücke KW - Spannstahlbruch KW - Schallemission KW - Fotogrammetrie KW - Faseroptik PY - 2022 AN - OPUS4-55686 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Safety of Prestressing Steels N2 - This talk reports the findings of the WIPANO "Knowledge and Technology Transfer via Patents and Standards" research project "Safety of Prestressing Steels," founded by the German Ministry of Economic Affairs and Climate Action (BMWK). A new test method for assessing the susceptibility of prestressing steels to hydrogen-induced stress corrosion cracking (SCC) is presented, which serves the demands of a lower scattering compared with the present standard. Moreover, the ability to differentiate between high susceptible and low susceptible prestressed wires is possible, modifying the method by hydrogen charging and surface preparation. T2 - Konferenz EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - ISO 15630-3 KW - Stress Corrosion Cracking KW - Prestressing Steels KW - Hydrogen KW - Constant Load Test PY - 2022 AN - OPUS4-55661 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Neue Erkenntnisse zu wasserstoffinduzierten Spannungsrissen infolge korrosiver Belastung hochempfindlicher Spannstähle in Spannblockverfahren nach TGL 173-33 N2 - Brückenbauwerke, die im Spannblockverfahren hergestellt wurden, können bauartbedingt wasserstoffinduzierte Spannungsrisse über den gesamten Querschnitt eines Spannkanals aufweisen. Das Risswachstum kann infolge dynamischer Beanspruchung über die Nutzungsdauer fortschreiten und zu Spanndrahtbrüchen führen. T2 - 5. Brückenkoloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Korrosion KW - Spannungsrisskorrosion KW - Brücke KW - Wasserstoff PY - 2022 AN - OPUS4-55663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin A1 - Hothan, Sascha A1 - Fürst, Richard T1 - Neue Prüfnorm für reaktive Brandschutzsysteme auf Stahlzuggliedern N2 - Der Vortrag stellt den Entwurf der neuentwickelten Prüfnorm vor. T2 - Workshop 2022 - Feuerwiderstand von Stahlzuggliedern mit reaktiver Brandschutzbeschichtung CY - Berlin, Germany DA - 06.09.2022 KW - Feuerwiderstand KW - Brandschutz KW - Stahlzugglieder KW - Reaktives Brandschutzsystem KW - Prüfnorm PY - 2022 AN - OPUS4-55701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fürst, Richard A1 - Häßler, Dustin A1 - Hothan, Sascha T1 - European test standard for intumescent coatings applied to steel tension bars with solid section N2 - Description of the FIRESTEMIC project and the newly developed test standard for reactive fire protection systems on steel tension members. T2 - Symposium 2022 Heißbemessung - Structural Fire Engineering CY - Brunswick, Germany DA - 13.09.2022 KW - Fire tests KW - Tension member KW - Intumescent coating KW - Steel KW - Test standard PY - 2022 AN - OPUS4-55702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kremberg, Jan A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Brandversuche an mechanisch belasteten Carbonzuggliedern N2 - Präsentation zu den Ergebnissen des Forschungsprojektes NeZuCa. T2 - 8th Symposium Structural Fire Engineering CY - Brunswick, Germany DA - 13.09.2022 KW - Carbon KW - Brandschutz KW - Feuerwiderstand KW - Brandversuch KW - Zugglied PY - 2022 AN - OPUS4-55705 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Ziegler, Fred A1 - Said, Samir A1 - Wille, Frank A1 - Quercetti, Thomas A1 - Minack, Mathias A1 - Sterthaus, Jens T1 - Dynamisches Verhalten und Überwachung des Großen Fallturms der BAM in Horstwalde N2 - Falltürme sind Bauwerke, die als Versuchsanlagen sehr speziellen, impulsartigen Belastungen ausgesetzt sind. Am Fallturm auf dem Testgelände Technische Sicherheit (TTS) der BAM wurde bei Routineinspektionen eine Abnahme der strukturellen Integrität in Form von Vorspannungsverlusten in den Bolzen der Stahlverbindungen festgestellt. Um ein Verständnis für die zugrundeliegenden Trag- und Schädigungsmechanismen zu erlangen, wurde ein umfassendes Structural Health Monitoring (SHM) System geplant und am Bauwerk installiert unter Nutzung von digitalen Bauwerksmodellen. Für die Auslegung des Überwachungssystems, insbesondere aber zur Unterstützung der Untersuchung des Schädigungsprozesses, wurden Finite-Elemente-Modelle erstellt. Um sicherzustellen, dass die FE-Modelle das reale Tragwerksverhalten mit ausreichender Genauigkeit abbilden, mussten sie jedoch in Bezug auf die gemessenen Antworten des Tragwerks kalibriert werden. Der vorliegende Beitrag beschreibt experimentelle und numerische Untersuchungen zur Identifizierung des strukturellen Systems des Stahlrohrgitterturms in Vorbereitung einer Überwachungskampagne. Die Auswertung von gemessenen Schwingungen unter ambienter Anregung ermöglichte die Identifizierung der Eigenfrequenzen mehrerer globaler Schwingungsmoden des Fallturms. Zur Modellvalidierung wurde zunächst eine Sensitivitätsanalyse durchgeführt, um die Parameter mit dem größten Einfluss zu ermitteln. Anschließend wurde ein evolutionärer Algorithmus (EA) zur Optimierung nach dem Prinzip der Minimierung der Differenzen zwischen gemessenen und simulierten charakteristischen Antworten eingesetzt. Das aktualisierte Modell wurde schließlich an der dynamischen Reaktion der Turmstruktur infolge einer realen Falltest-induzierten Stoßbelastung validiert. Die Ergebnisse zeigten eine gute Übereinstimmung zwischen numerischen und experimentellen Ergebnissen. N2 - Drop test towers are structures subjected to very specific dynamic loadings. At the drop test tower at the Test Site Technical Safety (TTS) of BAM routine inspections revealed a decline of structural integrity in form of loss of pretension in bolts of structural steel connections. To get an understanding about the underlying damage mechanisms as well as to assure the structural safety in operation, a multifaceted Structural Health Monitoring (SHM) system was planned and installed at the structure with the help of digital models. For planning the monitoring system but especially for supporting the investigation of the damaging process finite element models are deployed. Though, to ensure the capability of the FE model to reproduce the real structural behavior in sufficient accuracy, it needs to be calibrated in respect to measured responses of the structure. The present contribution describes experimental and numerical investigations to identify the structural system of the steel tube lattice tower in preparation of the monitoring campaign. An ambient vibration test allowed the identification of the natural frequencies of several global vibrational modes of the drop test tower. For model updating first a sensitivity analysis is applied to identify the most influencing parameter. In succession a genetic algorithm was applied for optimization in the sense of minimization of the difference between measured and simulated characteristic responses. The updated model is finally validated on the dynamic response of the tower structure to a real drop test induced impact loading. The results showed a good agreement between numerical and experimental results though the robustness of the simulation should be improved by more sophisticated numerical modelling. T2 - 7. VDI-Fachtagung Baudynamik CY - Würzburg, Germany DA - 27.04.2022 KW - Großer Fallturm Horstwalde KW - Structural Health Monitoring KW - Belastungsversuch KW - Modalanalyse KW - Schwingungsdynamik KW - Finite Elemente Simulation PY - 2022 AN - OPUS4-55470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Nerger, Deborah A1 - Moosavi, Robabeh A1 - Grunwald, Marcel T1 - Discussion on data evaluation of tomographic and numerical results N2 - The contribution discusses the processing and analysis of data generated on two different ways of investigations for impact damage in reinforced concrete structures. Damage investigations are essential to determine type and characteristics of damage and thus the residual capacity. Damage describing data is generated using two different types of investigation, a non-destructive tomographic as well as numerical examination. Subsequently, data of both sources was merged and analysed. Within the research project “Behaviour of structural components during impact load conditions caused by aircraft fuel tank collision” reinforces concrete plates were damaged by impact loading, see Hering (2020). Afterwards the damaged specimens were investigated tomographically as well as numerically using several methods and models. Aim of the presented research work was to specify an objective comparability of numerical data with experimentally determined damage patterns and based on this, to establish a quantitative damage evaluation. T2 - 26th International Conference on Structural Mechanics in Reactor Technology CY - Potsdam, Germany DA - 10.07.2022 KW - Impact damage of reinforced concrete KW - Tomographic damage evaluation KW - Numerical simulation of impact damage PY - 2022 AN - OPUS4-55476 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Said, Samir A1 - Ziegler, Fred A1 - Baeßler, Matthias A1 - Wille, Frank A1 - Quercetti, Thomas A1 - Minack, Mathias A1 - Sterthaus, Jens T1 - Structural Health Monitoring am Großen Fallturm der BAM N2 - In diesem Beitrag wird die Structural Health Monitoring Kampagne am Großen Fallturm der BAM vorgestellt. T2 - Seminar "Zerstörungsfreie Prüfung" CY - Online meeting DA - 13.01.2022 KW - Belastungsversuch KW - Großer Fallturm Horstwalde KW - Schwingungsdynamik KW - Modalanalyse PY - 2022 AN - OPUS4-55478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Taffe, A. A1 - Braml, T. T1 - Towards NDT supported decisions on the reliability of existing bridges N2 - 1) Concept for the NDT-supported assessment of existing structures 2) Demonstration: Shear force analysis of a prestressed concrete bridge T2 - ICOSSAR 2021-2022,13th International Conference on Structural Safety & Reliability CY - Online meeting DA - 13.09.2022 KW - Nachrechnung KW - Zuverlässigkeitsbewertung KW - Messunsicherheit KW - Querkraftnachweis PY - 2022 AN - OPUS4-55796 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Geophysical methods delivering input to geostatistical methods for geotechnical site characterization N2 - Geophysical methods are able to contribute significantly to geotechnical site characterization. In-situ parameters are collected and gaps between boreholes or other direct tests are filled with information. However the limited resolution has to be considered and the indirect geophysical parameters have to be translated into something geotechnically useful. Moreover, the limitations have to be evaluated when including geophysical data into geostatistical models. If done properly, the use of geophysics will help in an efficient and effective site characterization. A comprehensive overview on existing geophysical (mostly seismic) methods is given as well as information on the calibration of geophysical against geotechnical parameters, pitfalls and limitations and some hints how to include these data into geostatistical/geotechnical models. T2 - ICGoES International Conference on Geologicalk Engineering and Geosciences CY - Yogyakarta, Indonesia DA - 21.09.2022 KW - Geophysics KW - Geostatistics KW - Geotechnics PY - 2022 AN - OPUS4-55806 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John T1 - Fließeigenschaften von festen Gefahrgütern - Vergleich der Messung des Schüttwinkels und der Bestimmung des Hausner-Faktors N2 - Fazit: Nachteile der Schüttwinkel-Messmethoden: Einschränkungen bei der Anwendbarkeit auf Füllgüter mit bestimmten Eigenschaften; Die einzelnen Methoden liefern dann unterschiedliche Ergebnisse (statist. signifikante Abweichung der Mittelwerte); Schlechte Wiederholbarkeit; Bedienereinfluss spielt Rolle; Gewährleistung des Arbeitsschutzes schwierig; Bestimmung des Hausner-Faktors: Keins dieser Defizite Mögliche Abhilfemaßnahmen: Prüfbericht und Zulassungsschein sollten zumindest die Methode angeben, die zur Messung des Schüttwinkels 𝛼 eingesetzt wurde; Einheitliches Verfahren zur Schüttwinkelmessung (DIN-Methode)? Umstellung des Systems auf einen alternativen Parameter zur Bestimmung der Fließeigenschaften: Hausner-Faktor 𝐻: Bessere Wiederholbarkeit der Ergebnisse; Zuverlässige Anwendbarkeit auch auf Extremfälle von Schüttgütern; Sicherere Handhabung von Gefahrgütern T2 - 35. Sitzung des BAM AK Prüfstellen CY - Berlin, Germany DA - 21.09.2022 KW - Gefahrgutverpackungen KW - Schüttwinkel KW - Hausner-Faktor KW - Pulver PY - 2022 AN - OPUS4-55810 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Überwachung von Brücken mit digitalen Methoden N2 - Brücken werden durch Inspektionen und teilweise durch Monitoring überwacht, um Daten und Informationen über den Zustand und die Einwirkungen zu sammeln. Auf deren Grundlage werden Entscheidungen hinsichtlich Maßnahmen zur Gewährleistung der Sicherheit und Verfügbarkeit getroffen. In diesem Vortrag werden die Potentiale der Digitalisierung zur Unterstützung und Verbesserung der Brückenüberwachung diskutiert. Insbesondere werden die Bereiche Datenmanagement, Brückenmodellierung und Entscheidungsfindung betrachtet. T2 - BVPI Arbeitstagung 2022 CY - Berlin, Germany DA - 16.09.2022 KW - Entscheidungsfindung KW - Brücken KW - Überwachung KW - Digitalisierung KW - Datenmanagement KW - Modellierung PY - 2022 AN - OPUS4-55770 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Distributed fiber optic sensing @BAM N2 - Research and developement activities of BAM regarding Distributed Fiber Optic Sensing are portrayed using exemplary previous and current projects. Shown results pertain to distributed acoustic sensing (DAS), distributed temperagture sensing (DTS) and distributed strain sensing (DSS). T2 - Seismic seminar FU Berlin (group Prof. Shapiro) CY - Online meeting DA - 15.09.2022 KW - Distributed fiber optic sensing KW - Distributed acoustic sensing KW - Distributed temperature sensing KW - Distributed strain sensing KW - Infrastructure monitoring PY - 2022 AN - OPUS4-55721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino T1 - Das B 03 - Merkblatt - Übersicht N2 - Der Vortrag gibt eine Übersicht zu den Inhalten des B03 Merkblattes zur Potentialfeldmessung mit praktischen Anwendertipps. T2 - Lehrgang zum Erwerb des Sachkundenachweises zur Durchführung von Potentialfeldmessungen CY - Aachen, Germany DA - 12.09.2022 KW - Potentialfeldmessung KW - Korrosion KW - Stahlbeton KW - Spannbeton PY - 2022 AN - OPUS4-55726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klimek, André A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Auswirkung von passivem Zwang auf das Abplatzverhalten von Beton im Brandfall N2 - Beschreibung des Abplatzverhaltens von vier Prüfkörpertypen in Abhängigkeit der Ummantelungsart und Lagerungsbedingungen für zwei Betonrezepturen T2 - 8th Symposium Structural Fire Engineering CY - Brunswick, Germany DA - 13.09.2022 KW - Brand KW - Beton KW - Abplatzen KW - Zwang PY - 2022 AN - OPUS4-55734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -