TY - CONF A1 - Seyhan, E. A1 - Ebell, Gino A1 - Jimenez, D. A1 - Chavez, J. A1 - Sanchez Alvarez, G T1 - Evaluation of SACI performance on reinforced concrete structures N2 - Surface applied corrosion inhibitors (SACI) are widely used to mitigate corrosion process of steel reinforcement in concrete. But they remain controversial as to their effectiveness and the ability to compare materials from different manufacturers and technologies. They are applied onto the surface of hardened concrete and penetrate towards steel reinforcement. This paper discusses the corrosion inhibition performances of dual-phase surface applied corrosion inhibitor and the efficiency of the corrosion inhibitor is assessed by selected testing procedures in BAM laboratories. T2 - ACHE 2022 CY - Santander, Spain DA - 20.06.2022 KW - Corrosion KW - Inhibitor PY - 2022 AN - OPUS4-55095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mensinger, M. A1 - Fischer, O. A1 - Oberhaidinger, F. A1 - Stimmelmayer, L. A1 - Ebell, Gino A1 - Babutzka, Martin T1 - Grouted joint for integral composite frame bridges suitable for hot dip galvanizing N2 - Due to the corrosion resistance of carbon steel, bridge constructions are currently protected against corrosion by applied coating systems. These coating systems need to be renewed after approximately 25 50 years. Galvanized constructions without any welding areas at the construction site could be prepared as grouted joints and can be used without any renewing for about 100 years. T2 - Intergalva 2022 CY - Rome, Italy DA - 20.06.2022 KW - Corrosion KW - Galvanized steel KW - Bridge PY - 2022 AN - OPUS4-55096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Zündgefahren durch Funken - Grundlagen und Maßnahmen zum Explosionsschutz N2 - Hersteller von Geräten für den bestimmungsgemäßen Gebrauch in explosionsfähigen Bereichen müssen, wenn sie unter die Richtlinie 2014/34/EU fallen, für das Inverkehrbringen in EU-Mitgliedsstaaten eine Konformitätsbewertung durchführen. Dazu gehört eine Zündgefahrenbewertung, bei der auch nichtelektrische Zündquellen betrachtet werden müssen, zu denen die mechanischen Schlagvorgänge gehören. Bei dieser Zündquellenart kommt es infolge eines Schlages und/oder Reibens eines Bauteils auf ein anderes zu einer Energieumwandlung. Dadurch kommt es zu einer Temperaturerhöhung an der Kontaktstelle sowie unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Reibflächen als auch die abgetrennten Partikel stellen potentielle Zündquellen explosionsfähiger Atmosphären dar. Edelstahl ist für Geräte für die Verwendung zum bestimmungsgemäßen Gebrauch im explosionsgefährdeten Bereich insbesondere in der Chemie ein wichtiger Konstruktionswerkstoff. Die Ergebnisse des Forschungsprojektes "Entwicklung normativer Anforderungen an explosionsgeschützte nichtelektrische Geräte resultierend aus der Zündfähigkeit mechanisch erzeugter Schlagfunken (NAMES)" zeigen, dass Schlagvorgänge mit Edelstählen eine erhebliche Zündgefahr von explosionsfähigen Brenngasgemischen darstellen können. Dabei bestehen jedoch mitunter deutliche Unterschiede zwischen den verschiedenen Brenngasgemischen. Besonders hohe Zündwahrscheinlichkeiten konnten bei Brenngasgemischen mit Brenngasen der IEC-Explosionsgruppe IIC beobachtet werden, die Acetylen bzw. Wasserstoff als Brenngas enthielten. Schläge im Wasserstoff/Luft-Gemisch waren dabei jedoch bedeutend zündwirksamer. In diesem Gasgemisch konnte bei niedrigen maximalen Schlagenergien bis 60 J sogar eine mitunter höhere relative Zündhäufigkeit beobachtet werden als bei Versuchen mit unlegiertem Baustahl. T2 - Ausbildung zum Explosionsschutzbeauftragten CY - Essen, Germany DA - 21.06.2022 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Mechanischer Explosionsschutz KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Zündgefahrenbewertung KW - Funkenarme Werkzeuge KW - Funkenfreie Werkzeuge PY - 2022 AN - OPUS4-55098 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man T1 - Investigation of temperature effects on ultrasonic velocity in a prestressed concrete bridge model N2 - Ultrasonic measurements have recently been applied in the context of structural health monitoring in civil engineering. The ultrasonic method is very sensitive to environmental conditions and material property changes, which might be caused by prestress losses and loading effects on the bridge. However, it remains a challenge to identify the damage mechanisms causing structural property changes from the above-mentioned factors influencing ultrasonics. The focus of this contribution is to investigate the correlation between ultrasonic velocities and temperature by the coda wave interferometry (CWI) analysis. Long-term monitoring of a prestressed concrete bridge model under field conditions was carried out to observe the effect of temperature. The homogeneous change in concrete caused by temperature was revealed by applying the CWI method. The threshold value of the best correlation coefficients for the linear regression of temperature and ultrasonic velocity changes was also studied. Experimental assessment will provide a ratio for temperature correction to evaluate the prestressing force decrease and its consequences on crack opening or extension. T2 - Tagung EWSHM2022 CY - Palermo, Italy DA - 04.07.2022 KW - Ultrasonic velocity KW - Coda wave interferometry KW - Temperature correction KW - Prestressing force KW - Bridge monitoring PY - 2022 AN - OPUS4-55290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Wave propagation from hammer, vibrator and railway excitation – theoretical and measured attenuation in space and frequency domain N2 - The attenuation of wave amplitudes is ruled by the planar, cylindrical or spher-ical geometry of the wave front (the geometric or power-law attenuation) but also by the damping of the soil (an exponential attenuation). Several low- and high-frequency filter effects are derived for the layering and the damping of the soil, for the moving static and the distributed train loads and for a homoge-neous or randomly heterogeneous soil. Measurements of hammer- and train-induced vibrations at five sites have been analysed for these attenuation and filter effects. The measured attenuation with distance can be discribed by gen-eralised power laws and some reasons will be discussed. The theoretical filter effects can well be found in the measurements. T2 - 10th Wave Mechanics and Vibration Conference (WMVC)nce CY - Lisbon, Potugal DA - 04.07.2022 KW - Hammer impact KW - Train passage KW - Layered soil KW - Attenuation KW - Filter effects KW - Randomly heterogeneous soil KW - Scattering PY - 2022 AN - OPUS4-55246 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Häßler, Dustin T1 - Reaktive Brandschutzsysteme N2 - Die Präsentation gibt einen Überblick zum Anwendungsbereich und den -grenzen von reaktiven Brandschutzsystemen. Ferner werden Forschungsergebnisse der BAM vorgestellt. T2 - Stahlbau-Kalender-Tag 2022 CY - Stuttgart, Germany DA - 24.06.2022 KW - Reaktive Brandschutzsysteme KW - Feuerwiderstand KW - Stahlbau KW - Brandversuche KW - Dauerhaftigkeit PY - 2022 AN - OPUS4-55250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Charakterisierung von Salzbeton und alkali-aktivierten Material basierend auf der Schallemissionsanalyse N2 - Nach einer kurzen Einführung in die Schallemissionsprüfung und -Analyse wird ein Versuchsstand vorgestellt, der im Rahmen des Themenfeldprojektes Seal Waste Safe installiert wurde. Schwerpunkt des Vortrages sind die Schallemissionsmessungen an einem 150 l Demonstrator aus Salzbeton und einem weiteren aus alkali-aktiviertem Material. Neben der konventionellen Schallemissionsanaylse mit Aktivitäts- und Intensitätsparametern der Zeitsignale, werden auch frequenzbasierte Parameter zur Analyse andiskutiert. N2 - After a brief introduction to acoustic emission testing and analysis, an experimental test setup is presented, which was part of the Seal Waste Safe project (internal BAM project 2019-2022). Herein, the acoustic emission measurements of a 150 l demonstrator made of salt concrete and another one made of alkali-activated material are focused. In addition to the conventional acoustic emission analysis regarding the activity and intensity parameters of the detected time signals, also frequency-based parameters were discussed for analysis. T2 - Dauerhafte Verschlussbauwerke für Endlager CY - Online meeting DA - 14.2.2022 KW - Acoustic Emission KW - Schallemission KW - Salzbeton KW - Alkali aktiviertes Material KW - Geopolymer PY - 2022 AN - OPUS4-54937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine A1 - Munsch, Sarah T1 - Potential automatisierter NMR-Messungen zur Ermittlung von Hydratationseigenschaften - ein Vergleich mit Vicat- und Wärmeflusskalorimetrie-Ergebnissen N2 - Es werden Ergebnisse von 1H-NMR-Relaxometrie-Messungen an Salzbeton und einem alkali-aktivierten Material, die im Rahmen des Themenfeldprojektes Seal Waste Safe durchgeführt werden, vorgestellt. Dabei wird die zeitliche Entwicklung von ausgewählten Merkmalen der ermittelten T2-Relaxationszeitenverteilungen während der Hydratation betrachtet. Als Referenz zur Identifikation von charakteristischen Hydratationsereignissen dienen der Vicat-Nadeleindringversuch und Wärmeflusskalorimetrie. T2 - Online-Workshop „Dauerhafte Verschlussbauwerke für Endlager“ CY - Online meeting DA - 14.02.2022 KW - NMR-Relaxometrie KW - Alkali-aktiviertes Material KW - Salzbeton KW - Seal Waste Safe PY - 2022 AN - OPUS4-54945 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Potentialfeldmessung in Theorie und Praxis N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbedingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanierungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz T2 - Vorlesung TU-Berlin CY - Berlin, Germany DA - 30.06.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-55156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilrich, Cordula T1 - Chemikalienrecht & Gefahrstoffrecht: Schnittstelle zu Seveso-Richtlinie & Störfallverordnung N2 - Der Vortrag beleuchtet die Schnittstelle zwischen Chemikalienrecht und Störfallrecht. Der Hintergrund, die Struktur und wichtige Eckpunkte der CLP-Verordnung werden vorgestellt. Instrumente und Beispiele zur Verifizierung von Einstufungen nach CLP im Hinblick auf die Anwendung unter der Seveso-Richtlinie bzw. der Störfallverordnung werden erläutert. Außerdem werden mögliche Konsequenzen für Änderungen im Anwendungsbereich der Seveso-Richtlinie besprochen. T2 - BAM/UBA-Behördenerfahrungsaustausch CY - Berlin, Germany DA - 27.06.2022 KW - Anlagensicherheitsrecht KW - Chemikalienrecht KW - CLP-Verordnung KW - Gefahrstoff KW - GHS KW - Seveso-Richtlinie KW - Störfallverordnung PY - 2022 AN - OPUS4-55171 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Karapanagiotis, Christos T1 - Brillouin optical frequency-domain analysis for structural health monitoring N2 - We present our achievements in the development of distributed fiber optic sensing systems based on Brillouin optical frequency-domain analysis for structural health monitoring. The focus of the applications is on the gapless monitoring of geotechnical structures, large area infrastructures and electrical grids. The work includes the latest use of machine learning algorithms to reduce measurement time by coexistent increasing the measurement accuracy. T2 - 4th Workshop on Optomechanics and Brillouin Scattering CY - Erlangen, Germany DA - 14.06.2022 KW - Distributed sensing KW - BOFDA KW - Optical fiber sensor KW - Brillouin distributed fiber sensor PY - 2022 AN - OPUS4-55173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Development of an analysis and testing concept for the evaluation of impact targets in the mechanical safety testing of dangerous goods packagings N2 - The mechanical and geometrical properties of impact targets greatly influence the outcome of a drop test. The International Agreement concerning the International Carriage of Dangerous Goods by Road (ADR) as well as ISO 2248 describe the characteristics of impact targets for drop tests of dangerous goods packagings. According to these regulations, the impact target’s surface needs to be unyielding, under testing conditions non-deformable, flat, and integral with a mass at least 50 times that of the heaviest packaging to be tested. The problem is that many production facilities, especially manufacturers of corrugated fibreboard boxes, do not have their own testing device with the required 50 times mass ratio of the impact target for a regulation compliant drop test during series production. Furthermore, at UN level it is considered necessary to revise these requirements. In the present paper, the impact target requirements are examined in detail and compared with those in other technical areas (e.g., impact target for container for the transport of radioactive materials). A research method is being developed to investigate the dependency between the mass ratio of the packaging and the target as well as the damage resistance of a drop tested package in relation to specific design characteristics. The results are of high relevance for industry purposes and intended to ensure a uniform level of safety assessment for the mechanical testing of dangerous goods packagings. T2 - IAPRI Bangkok 2022, 23rd World Packaging Conference CY - Online meeting DA - 12.06.2022 KW - Corrugated fibreboard boxes KW - Dangerous goods packagings KW - Drop test KW - Impact target KW - Structural dynamics PY - 2022 AN - OPUS4-55121 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John A1 - Vogler, Nico A1 - Goedecke, Thomas T1 - Flow properties of powdery or granular filling substances of dangerous goods packagings - Comparison of the measurement of the angle of repose and the determination of the Hausner ratio N2 - To ensure safety when transporting dangerous goods, it is important to specify the flow properties of the respective solid filling substance of the packagings. For this purpose, the angle of repose is currently used for the UN approvals in Germany. Measurements were carried out on 12 powdery or granular substances applying the angle of repose measuring methods customary in the test centres. The results of the methods differ significantly from each other. In addition, some of the techniques cannot be applied for very cohesive or coarse-grained materials. The results for the angle of repose show a strong scatter for some constellations (coefficient of variation more than 20 %). Safety during transport of dangerous goods cannot be guaranteed with this currently practiced system of measuring the angle of repose. As a consequence, an alternative parameter to characterize the flow properties of bulk materials should be used in the recognized test centers for dangerous goods packagings, such as the Hausner ratio. This approach leads to more precise test results for the substances examined (maximum coefficient of variation 2.8 %). It also has advantages in terms of applicability and occupational safety. Since the flow properties are safety-relevant, both in terms of mechanical safety and safety against the release of dangerous substances, the testing practice in the recognized test labs should be improved and standardized. T2 - IAPRI Bangkok 2022 23rd World Packaging Conference CY - Online meeting DA - 12.06.2022 KW - Sift-proofness KW - Powders KW - Flow properties KW - Flowability KW - Angle of repose KW - Hausner ratio PY - 2022 AN - OPUS4-55103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando T1 - Prüfung von Spannstählen N2 - Ein Stand zum WIPANO-Projekt Spannstahlsicherheit wurde auf Anfrage in einer Gemeinschaftssitzung des AK "Eisen und Stahl" sowie des AK "Korrosionsuntersuchung und -überwachung" der Gesellschaft für Korrosionsschutz e.V. (GfKORR) präsentiert. Das Projekt hat die Verbesserung der produktspezifischen Prüfnorm ISO 15630-3 als Ziel. Vorgestellt wurden die Wahl der neu entwickelten Wasserstoffbeladung mit galvanostatischer kathodischer Polarisation und die Frage, ob die Prüfung an Lieferoberflächen sinnvoll ist. T2 - Gemeinschaftssitzung des AK "Eisen und Stahl" sowie des AK "Korrosionsuntersuchung und -überwachung" der Gesellschaft für Korrosionsschutz e.V. (GfKORR) CY - Online meeting DA - 23.06.2022 KW - ISO 15630-3 KW - Spannstahl KW - Spannungsrisskorrosion KW - Wasserstoff KW - Permeationsmessung PY - 2022 AN - OPUS4-55105 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fladt, Matthias A1 - Weise, Frank A1 - Wieland, Marko T1 - Internal water-repellent treatment - a novel strategy for mitigating alkali-aggregate reaction in concrete road pavements N2 - To prevent future alkali-aggregate reaction (AAR) damage, which has occurred frequently in the German highway network in recent years, a new regulation has been drafted. This regulation severely limits the use of alkali-sensitive aggregates by requiring that their suitability be verified by certified inspectors using newly developed AAR concrete tests that involve the external supply of alkali. This has led to a significant limitation in the number of aggregates usable for concrete pavements. A novel AAR avoidance strategy is now being pursued, which aims to enable the use of borderline alkali-sensitive aggregates through the application of an internal water-repellent treatment. The addition of water repellents during concrete production should significantly reduce the ingress of water and external de-icing salts into the concrete pavement, thus reducing the potential for AAR damage. This paper presents the results of laboratory tests to assess the suitability of this new AAR prevention strategy. Representative, highly AAR-susceptible road paving concrete made with an alkali-sensitive greywacke and various water repellents were used as the basis for these experiments. The tests for concrete suitability included determining the conventional fresh and hardened concrete properties as well as concrete prism tests with external alkaline supply. Building on these results, laser-induced breakdown spectroscopy (LIBS) analyses of de-icing-salt intrusion as well as microscopic examinations for verification of the AAR characteristics were carried out. The results of the AAR concrete tests with external alkaline supply support the conclusion that, when hydrophobic agents containing a suitable active ingredient are used, the AAR damage process in road paving concrete can be sufficiently prevented. T2 - 16th International Conference on Alkali-Aggregate Reaction in Concrete CY - Lisbon, Portugal DA - 31.05.2022 KW - Concrete pavements KW - Internal water-repellent treatment KW - Preventive measures KW - Testing for potential alkali-aggregate reaction PY - 2022 AN - OPUS4-55185 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Fugenfüllungen - Anforderungen, Eigenschaften, Prüfungen, Dauerhaftigkeit N2 - Fugenfüllungen im kommunalen Stadtstrassenbau unterliegen besonderen mechanischen Beanspruchungen. Hier kommt es bereits bei der Planung darauf an, Fugenausführungen und insbesondere Fugenfüllstoffe bewusst nach ingenieurtechnischen Gesichtspunkten auszuwählen. Dazu ist das ingenieurtechnische Verständnis der relevanten Fugenfüllstoffe - Funktionsweise, Leistungskriterien, Prüfungen, Dauerhaftigkeit - von entscheidender Bedeutung. Der Vortrag erläutert nicht nur die maßgebenden Fugenfüllstoffe unter den vorgenannten Schwerpunkten, sondern stellt auch das Verständnis zu den Rahmenbedingungen, Grundlagen und Wirkmechanismen des entsprechenden technischen Regelwerkes her. Neueste Entwicklungen werden den Praxisvertretern näher gebracht und erläutert. Die Zusammenhänge und Strategien zur Weiterentwicklung der „Betonstrasse der Zukunft“ werden diskutiert und dargestellt. T2 - Qualitätsgemeinschaft Städtischer Strassenbau (QGS) - Weiterbildung für technisches Führungspersonal CY - Berlin, Germany DA - 14.06.2022 KW - Kommunale Infrastruktur KW - Betonfahrbahndecken KW - Qualitätssicherung KW - Verfügbarkeit PY - 2022 AN - OPUS4-55070 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Grundlagen der Korrosion N2 - Darstellung der Grundlagen der elektrochemischen Korrosion von metallenen Werkstoffen im Bauwesen. Dabei liegt das Hauptaugenmerk auf dem Zusammenhang zwischen Energieaufwand für den Herstellungsprozess und daraus resultierendem thermodynamisch instabilen Zustand und Korrosionsneigung. Der Einfluss der Deckschicht- Oxidschichtbildung wird ebenfalls behandelt. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Elektrochemische Messungen N2 - Elektrochemische Messungen könne, richtig angewandt, dazu dienen ein Korrosionssystem ausreichend gut zu beschreiben. Im Bauwesen, speziell bei Stahl in Beton, ist es jedoch ohne Kenntnis der korrodierenden Flächen oft nur möglich zwischen aktiv korrodierenden Bereichen und passiven, als Kathode wirksamen, Bereichen zu differenzieren. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Potentialfeldmessung KW - Korrosion PY - 2022 AN - OPUS4-54869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Merkblatt B 03 der DGZfP - Ausgabe April 2014 N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbedingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanierungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54870 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan T1 - Comparative Study on Standardized Ignition Sources Part 2: Exploration of the Initial Igniting Volume of Standardized Ignition Sources for the Determination of Explosion Characteristics N2 - There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible. While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique. T2 - Loss Prevention CY - Prague, Czech Republic DA - 06.06.2022 KW - Ignition source KW - Hybrid Mixtures KW - 20L-sphere PY - 2022 AN - OPUS4-55029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino T1 - Erörterung des Messprotoklls N2 - Das für die Potentialfeldmessung in der neusten Ausgabe des Merkblattes B03 der DGZfP erarbeitete Messprotokoll berücksichtigt sowohl en Einsatz, von Stab-, Einrad- oder Vierradelektroden. In diesem Vortrag wird auf alle varianten des Gegenmessen von Bezugselektroden im Einsatz eingegangen, ebenso wie auf das Erfassen der notwendigen Randparameter. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54871 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Mögliche Fehlerquellen in der Praxis N2 - Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. Bei der Durchführung dieser Messung gibt es jedoch messtechnikspezifische Fehlerquellen und äußere Einflüsse aus dem zu untersuchenden Bauwerk die eine Interpretation der Messergebnisse signifikant beeinflussen können. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Spannbetonbauwerke - Von der Initiierung zum Schaden N2 - Wasserstoffinduzierte Spannungsrisskorrosion an hochfesten und hochempfindlichen Spannstählen führt an bestehenden Brückenbauwerken nach Jahren der Rissinitiierung zu Trag- und Standsicherheitsverlusten. Anhand des Beispiels der Brücke am Altstädter Bahnhof gibt es eine bauartbedingte Schadensinitiierung die über den gesamten Spannkanalquerschnitt zu Spannungsrisskorrosion führen kann. T2 - AK-Sitzung Korrosionsschutz im konstruktiven Ingenieurbau CY - Online meeting DA - 12.05.2022 KW - Spannungsrisskorrosion KW - Korrosion PY - 2022 AN - OPUS4-54874 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Hüllmann, Dino A1 - Winkler, Nicolas P. A1 - Schugardt, Jan T1 - Remote Drone-to-Drone Gas Sensing: A Feasibility Study N2 - Remote gas sensors mounted on mobile robots enable the mapping of gas distributions in large or poorly accessible areas. A challenging task however, is the generation of three-dimensional distribution maps from these spatially sparse gas measurements. To obtain high-quality reconstructions, the choice of optimal measuring poses is of great importance. Remote gas sensors, that are commonly used in Robot Assisted Gas Tomography (RAGT), require reflecting surfaces within the sensor’s range, limiting the possible sensing geometries, regardless of whether the robots are ground-based or airborne. By combining ground and aerial robots into a heterogeneous swarm whose agents are equipped with reflectors and remote gas sensors, remote inter-robot gas measurements become available, taking RAGT to the next dimension – releasing those constraints. In this paper, we demonstrate the feasibility of drone-to-drone measurements under realistic conditions and highlight the resulting opportunities. T2 - 19th International Symposium on Olfaction and Electronic Nose CY - Aveiro, Portugal DA - 29.05.2022 KW - Aerial robot KW - TDLAS KW - Inter-robot measurements KW - Gas tomography KW - Plume PY - 2022 AN - OPUS4-54927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Erdt, René A1 - Gödde, M. A1 - Salg, S. T1 - Self-ignition Behaviour of Bulk Materials: How Reliable is the Extrapolation of Laboratory Tests? N2 - The self-ignition behaviour of bulks is usually determined with the aid of isoperibolic or adiabatic hot storage tests; the sample volumes here are typically in the range of approx. 100 cm³ to several litres. The extrapolation to technically relevant volumes holds, however, considerable uncertainties. To reduce these uncertainties, a test stand was set up that allows to investigation sample sizes of up to 1000 dm³. These allow the study of selfignition behavior closer to the conditions that prevail in practice. The suitability (or unsuitability) of the established methods (including dangerous goods classification tests) were to be demonstrated and influencing variables that cannot be measured on a laboratory scale were to be determined. In addition, various analytical methods were used for the determination of reaction kinetic data of solid bulk materials and to predict the self-ignition behaviour of large storages. These are thermal analyses such as differential scanning calorimetry DSC, simultaneous thermal analysis STA as well as microcalorimetry for highprecision measurement of heat flows. Complete test series using all mentioned test methods will be presented for crosslinked polyvinyl-pyrrolidone (PVP) and conclusions regarding the applicability of the extrapolation methods will be discussed. Hot storage tests up to semi-industrial scale and their combination with various thermoanalytical methods allow a much more precise prediction of the self-ignition behaviour of large bulks. A further promising approach to estimate their heat release rates, and hence, the risk of self-ignition under technical conditions, is the use of microcalorimetric methods. T2 - Loss Prevention 2022 CY - Prague, Czech Republic DA - 05.06.2022 KW - Self-ignition KW - Kinetic data KW - Semi-technical tests KW - Thermoanalytical methods PY - 2022 AN - OPUS4-55080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Wasserstoff - Kryogene Anwendungen N2 - Wasserstoff wird als ein potenzieller alternativer Energieträger gesehen, mit dem die für 2050 gesetzten Klimaziele erreicht werden könnten. Der Transport von Wasserstoff ist mittels verschiedener Speichertechniken möglich, von denen der kryogene Transport mit den größten volumetrischen Energiedichten einhergeht. Hierdurch eignen sich diese Speicher besonders für die energieintensiven Verkehrsmittel im Land-, See- und Flugverkehr. Im Vortrag werden Speichertechniken, Gefahren im Umgang mit kryogenen Gasen sowie bisherige Störfälle dargestellt. Darauf aufbauend wird ein Teil der aktuellen Forschungsarbeit an der BAM vorgestellt, die die Sicherheit dieser Speicher unter außergewöhnlichen Belastungen adressiert. T2 - 26. Gefahrgutkongress Mecklenburg-Vorpommern CY - Rostock, Germany DA - 03.11.2022 KW - Wasserstoff KW - H2 KW - LNG KW - LH2 KW - Tank PY - 2022 AN - OPUS4-56181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Battig, Alexander T1 - Flame Retardancy Forge on Sustainability - Fun, Food for Thought, Future N2 - This presentation outlines the role biogenic flame retardant fillers play in attaining sustainability goals associated with the bioeconomy. The talk presents biogenic waste compounds as flame retardant syngergists with phosphorus flame retardants in various polymers. T2 - Climate Change @ Fire Science Workshop CY - Berlin, Germany DA - 10.11.2022 KW - Sustainable KW - Flame retardancy KW - Bioeconomy PY - 2022 AN - OPUS4-56285 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Entwicklung der Potentialfeldmessung –forschung, Regelwerk, Fortbildung N2 - Ein Übersichtsvortrag zur Entwicklung der Prüfmethode zu einem etablierten und geregelten Messverfahren für die Korrosionszustandsermittlung von Stahlbetonbauwerken. T2 - GfKORR Jahrestagung - Aktuelles aus der Korrosionsforschung - Nutzen und praktische Anwendungen CY - Frankfurt a. M., Germany DA - 08.11.2022 KW - Potentialfeldmessung KW - Korrosion KW - Stahlbeton KW - Korrosionsprüfung PY - 2022 AN - OPUS4-56206 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Zündgefahren durch Funken-Grundlagen und Maßnahmen zum nichtelektrischen Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA22-00188-050-E) im Haus der Technik (HdT) - Außeninstitut der RWTH Aachen und der Universität Duisburg-Essen, 45127 Essen CY - Essen, Germany DA - 08.11.2022 KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Mechanischer Explosionsschutz KW - Nichtelektrischer Explosionsschutz PY - 2022 AN - OPUS4-56211 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schendler, Thomas T1 - Arbeit der Kommission für Anlagensicherheit (KAS) N2 - Kurze Vorstellung der KAS; Aktuelles Arbeitsprogramm; Kurze Darstellung von Ergebnissen; Stand Diskussion/Verfolgung von Ereignissen/Störfällen; Kurze Vorstellung der Ergebnisse des FuE-Vorhabens „Umfassende systematische Auswertung von Störfällen und sonstigen Ereignissen in industriellen Anlagen“ T2 - Kolloquium Anlagensicherheit/Störfallvorsorge CY - Dresden, Germany DA - 29.09.2022 KW - KAS KW - Ereignisse KW - Störfälle PY - 2022 AN - OPUS4-56125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Achievements and challenges of distributed polymer optical fiber sensors @BAM N2 - Monitoring of construction projects plays increasingly important role in the implementation of growing needs and requirements, especially in geologically difficult areas. This particularly concerns tunnelling and special civil engineering projects. The use of fiber optic sensors for structural health monitoring provides significant economic advantages regarding lower life-cycle costs of the civil infrastructure. We present our achievements in the development of distributed polymer optical fiber sensors based on Rayleigh and Brillouin scattering for early damage detection. T2 - POF Conference CY - Bilbao, Spain DA - 26.09.2022 KW - Distributed POF sensor KW - OTDR KW - OFDR KW - Smart geosynthetics PY - 2022 AN - OPUS4-56031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Said, Samir A1 - Rohrmann, Rolf T1 - Measurement and evaluation tools for ground and building vibrations from industrial process-es, construction work, traffic and other sources N2 - Vibration measurements have many causes and many technical and natural sources. Problems can sometimes be solved by short-term measurements, but in many cases, a long-term measurement is necessary. In long-term measurements of days, weeks, months and even years, it is easy to collect a huge quantity of raw data, but at the end, the post-processing of these data can be exhausting (for example one-year vibration data of a wind energy tower). A software has been developed which con-sists of measuring and evaluation routines where the measuring routines can operate different meas-uring systems and different measuring cards. The main advantage of this software is the fact that the interesting evaluations can be integrated in the measuring process so that the characteristics of the vibration can be extracted without storing all the raw data. Only important time segments are stored, for example train passages. The overall concept of the software and the main evaluation routines will be described in some details. Examples of our measurement experience will illustrate the capabilities of the software. 1) Surveying construction work in nearby sensitive buildings (for example an old wind tunnel), including a stable alarm system and meaningful vibration limits. 2) Prediction of train-induced vibration for a planned building to prevent annoyance and to improve the building design. 3) Modal analysis and long term measurements of several single- or multi-span, concrete or steel bridges 4) Modal and wave analysis of coupled floors in a historical building (“Neues Palais” at Potsdam). 5) Soil properties of various measurement sites (different routines to evaluate the dispersion). Moreover, from many projects, amplitudes, frequencies, and attenuation laws have been collected and analysed for the different sources such as vibratory or impact pile driving and ground compaction, demolition work with different machines, blasting in quarries and in tunnel works, bomb and mine clearing. T2 - 28th International Congress on Sound and Vibration (ICSV28) CY - Online meeting DA - 25.07.2022 KW - Ground vibration KW - Building vibration KW - Measurement KW - Evaluation KW - Modes and waves PY - 2022 AN - OPUS4-56035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Effects of a varying track and soil stiffness on ground vibrations near railway lines N2 - Usually, geometric irregularities are considered as the main cause of ground vibrations from trains. A varying stiffness of the track, the track support and the soil can also generate ground vibrations. The regular stiffness variation of the track on and between the sleepers results in a deterministic dynamic axle load. The random stiffness variation of the track support yields also dynamic axle loads. The dynamic axle loads are generated by the varying wheel displacements under the static axle load by the acceleration of the unsprung mass of the rail vehicle. The random stiffness variation has a second effect. The pulses from the passage of the static axle loads are superposed regularly to the quasi-static response, but also irregularly to yield a “scattered” part of the axle pulses. The same holds for a random variation of the soil stiffness. All these effects of stiffness variations have been calculated by wavenumber-domain multi-beam track models, a random finite-element soil model and the superposition of axle impulses in a stochastic simulation. The results are confronted with many measurements at different sites. It is concluded that the stiffness variation of the track and the soil generate an important ground vibration component near railway lines. T2 - Railways 2022 CY - Montpellier, France DA - 22.08.2022 KW - Ground vibration KW - Railways KW - Varying track stiffness KW - Varying soil stiffness PY - 2022 AN - OPUS4-56036 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Railway-induced ground and building vibrations – Analysis in frequency-wavenumber domain and fast prediction with approximate models N2 - A simple and fast prediction scheme is presented for train-induced ground and building vibrations. For the emission, finite-element boundary-element or multiple-beam-on-continuous-soil models of the track have been analysed and approximated by faster track-on-Winkler-soil models. The vehicle-track interaction due to irregularities yields the excitation forces. For the transmission of waves in the soil, the wavenumber integral of the compliance of layered soils has been evaluated. The calculation time is reduced for the prediction by using the solution of a homogeneous half-space with a frequency-dependent wave velocity (the dispersion) of the soil. For the immision, many 2 and 3-dimenisonal finite-element building models have been investigated, and a good approximation has been established by a 1-dimensional soil-wall-floor model. In addition, the axle sequence of the train, the quasi-static and the “scattered” response of the soil, and the wave propagation from a tunnel to a pile foundation of a building have been included. T2 - ISMA-Conference CY - Leuven, Belgium DA - 12.09.2022 KW - Ground vibration KW - Building vibration KW - Railways KW - Simple and fast prediction PY - 2022 AN - OPUS4-56038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Seifert, Lando A1 - Ebell, Gino T1 - Vorstellung Projektergebnisse Wipano Vorhaben Spanntahlsicherheit N2 - Diese Präsentation stellt die Ergebnisse des abgeschlossenen WIPANO Vorhabens "Spannstahlsicherheit" vor, welches von der BAM in Kooperation mit dem Stahlwerks Annahütte und der Max Aicher GmbH bearbeitet wird. Es werden die Projektziele näher beleuchtet und verschiedentliche Highlights der erzielten Untersuchungsergebnisse vorgestellt. T2 - DIN-Ausschussitzung des NA 062-01-77 AA "Korrosionsprüfverfahren" CY - Berlin, Germay DA - 19.10.2022 KW - Korrosion KW - Spannstahl KW - Spannbetonbauwerke KW - Spannungsrisskorrosion KW - Wasserstoffversprödung PY - 2022 AN - OPUS4-56059 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer A1 - Zirker, Stefan T1 - Photothermal determination of thermal properties of concrete – a method evaluation N2 - The evaluation of thermal properties is probably an underrated tool for the onsite health monitoring of concrete structures. The photothermal approach offers a possibility to realize a real onsite measurement. This contribution presents the application of the photothermal approach under lab conditions on three different concrete types. The obtained results were compared with those of a commercial device based on the Transient Plane Source (TPS) method. Both agreed well within the estimated uncertainty ranges and therefore demonstrate the applicability of the photothermal method for this kind of investigations. First results of a concrete sample with different water contents support the potential of this method for the characterization of concrete in general. T2 - NDTCE 2022 CY - Zurich, Switzerland DA - 16.8.2022 KW - Thermal effusivity KW - Thermal conductivity KW - Moisture PY - 2022 AN - OPUS4-56063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Committee Meeting to WIPANO "Safety of Prestressing Steels" N2 - A conclusion on the WIPANO research project "Safety of Prestressing Steel" was presented in the final committee meeting at the end of the project. The project's exciting findings and recommendations for a new method were discussed with the audience of national and international stakeholders of the prestressing steel industry and representatives of inspection bodies and standardization. T2 - Committee Meeting to WIPANO research Project CY - Online meeting DA - 29.09.2022 KW - ISO 15630-3 KW - Prestressing Steels KW - Hydrogen-induced Stress Corrosion Cracking KW - Hydrogen PY - 2022 AN - OPUS4-56101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Mythos oder Wahrheit - die kalte Pyrotechnik N2 - Beschreibung akktueller Gefährdungen beim Missbrauch von Pyrotechnik in Stadien, insbesondere Fackeln. Produktentwicklung "kalte Pyrotechnik" wurde bewertet im Hinblick auf Temperatur und Aerosolemissionen. T2 - 22. Internationales Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 28.11.2022 KW - Pyrotechnik KW - Fackeln KW - Aerosole KW - Fussballstadien PY - 2022 AN - OPUS4-56448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunert, Wiebke T1 - EU project ODYSSEUS - year 1 N2 - Vorstellung EU-Projekt ODYSSEUS zum Thema Home-Made-Explosives sowie erste Ergebnisse bzgl. Rezepten, Ausgangsstoffen und Home-Made-Explosives in diesem Zusammenhang. T2 - 22. Internationales Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 28.11.2022 KW - Home-Made-Explosives KW - Precurser PY - 2022 AN - OPUS4-56449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liebner, Christian A1 - Patzelt, Anne-Katrin A1 - Krentel, Daniel T1 - BAM Testgelände Technische Sicherheit (TTS) N2 - Die Präsentation zeigt in Bild und Video die Möglichkeiten auf dem BAM TTS zur Durchführung von Versuchen unterschiedlicher Gefährlichkeitsstufen auf. Sie wendet sich an potentielle künftige Kooperationspartner aus dem Bereich der zivilen Sicherheitsforschung (Polizeibehörden, Feuerwehr, THW, andere Forschungseinrichtungen), um deren Forschungsbedarf mit den an der BAM vorhandenen Testmöglichkeiten abzugleichen und so ebenfalls dem Aufbau von überflüssigen konkurrierenden Parallelstrukturen an anderen Forschungseinrichtungen vorzubeugen. T2 - ForAn Anwendertreffen zum BMBF-Innovationsforum "Zivile Sicherheitsforschung" CY - Berlin, Germany DA - 02.05.2022 KW - Zivile Sicherheitsforschung KW - Großversuche KW - Testgelände PY - 2022 AN - OPUS4-54847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Wellenausbreitung und Pfähle im inhomogenen Boden – Gesetzmäßigkeiten für die Gründung von Windenergieanlagen und für die Prognose von Bahnerschütterungen aus Tunneln N2 - Es wird eine gekoppelte Finite-Element-Randelementmethode zur Berechnung von Pfahlgrün-dungen in inhomogenen (geschichteten) Böden vorgestellt. Sie beruht auf den Greenschen Funktionen (Punktlastlösungen) für inhomogene Böden. Diese Lösungen können auch für die Wellenausbreitung in der Tiefe, zum Beispiel von einem Bahntunnel zu einem eingebetteten Gebäude, dem Kellergeschoss benutzt werden. Die Punktlastlösungen in der Tiefe werden mit der Halbraumlösung an der Bodenoberfläche und mit der Vollraumlösung verglichen und Gesetzmäßigkeiten für geschichtete Böden abgeleitet. Zu den Pfahlgründungen werden die Horizontalnachgiebigkeiten von Pfählen in geschichteten Böden dargestellt. Für den homoge-nen und den kontinuierlich steifer werdenden Boden werden Potenzgesetze für den Boden- und Pfahleinfluss aufgestellt. Der Vergleich mit dem Winkler-Modell der rein lokalen Boden-reaktion zeigt, dass die Winkler-Bettung in allen Fällen einen zu kleinen Bodeneinfluss ergibt. T2 - 7. VDI-Fachtagung Baudynamik CY - Würzburg, Germany DA - 27.4.2022 KW - Wellenausbreitung in der Tiefe KW - Pfahlnachgiebigkeiten KW - Erschütterungen KW - Tunnel PY - 2022 AN - OPUS4-54769 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kremberg, Jan A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Fire tests of carbon tension members for lightweight constructions N2 - Vorstellung der Brandversuche im Rahmen des Projektes NeZuCa an Carbonzuggliedern für den Brückenbau. T2 - ClimateChange@FireScience CY - Berlin, Germany DA - 10.11.2022 KW - Fire tests KW - Carbon KW - Lightweight constructions KW - Fire Science PY - 2022 AN - OPUS4-56302 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilrich, Cordula T1 - TRGS 510 Lagerung von Gefahrstoffen in ortsbeweglichen Behältern N2 - Der Vortrag stellt die wesentlichen Inhalte sowie die wichtigsten Änderungen der TRGS 510 "Lagerung von Gefahrstoffen in ortsbeweglichen Behältern" vor. Die TRGS 510 zeichnet sich durch ein gestuftes Maßnahmenkonzept in Abhängigkeit von der Art und Menge der gelagerten Gefahrstoffe aus. Folgende Maßnahmenstufen werden durch die TRGS 510 beschrieben: 1. Kleinmengen -> Allgemeine Maßnahmen 2. Überschreitung der Kleinmengen -> Lagerung im Lager 3. Überschreitung bestimmter Mengen für spezielle Gefahrstoffe -> Spezielle Maßnahmen 4. Verschiedene Gefahrstoffe und Lagerung im Lager erforderlich -> ggf. Getrenntlagerung und Separatlagerung T2 - Fachfortbildung im Umgang mit Chemikalien beim Bildungszentrum der Bundeswehr CY - Mannheim, Germany DA - 21.11.2022 KW - Gefahrstoffe KW - Lagerung KW - TRGS KW - Technische Regeln Gefahrstoffe KW - Arbeitsschutz PY - 2022 AN - OPUS4-56365 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abraham, O. A1 - Niederleithinger, Ernst A1 - Schmidt, F. A1 - Dalsgaard-Soerensen, J. A1 - Thoens, S. A1 - Chapeleau, X. A1 - Ferria, H. T1 - Infrastar Training School on Fatigue and Reliability Analysis of Structures - Training for Assessment of Risk N2 - The Infrastar training school provides lectures and hands-on training to Master and PhD students, early-stage researchers and (young) professionals on all aspects of asset management of civil infrastructures with respect to fatigue of materials. It is organized yearly since 2019 and up to 20 profiles are selected to attend the 3.5-day training. A team of 7 teachers provides insight in multi-disciplinary and intersectoral basic concepts in three core fields, ranging from the design to the dismantling of the structures (bridges and wind turbines): 1. Monitoring and auscultation, 2. Structural and action models, 3. Reliability, risk and decision analyses. Each year, a recognized expert is invited to deliver a keynote lecture to raise interest in a specific aspect of one of the fields covered. The presentation is recorded and published on the training school website. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Doctoral School KW - Fatigue KW - Reliability KW - Concrete PY - 2022 AN - OPUS4-56349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia A1 - Hubert, T. T1 - metabuilding labs: OITB presentation and how BAM an NBK can contribute N2 - The aim of the project metabuilding labs to establish an EU wide network of testing facilities and innovation services for new building envelope technologies & products is presented. Further the envisaged contribution of BAM and the private Frech research center NOBATEK is explained. T2 - ENBRI/BBRI workshop “Hygrothermal testing – a necessity to guarantee durable buildings” CY - Brussels, Belgium DA - 21.09.2022 KW - Building envelope KW - Building facade KW - Test bench KW - Pilot building KW - Open innovation testbed PY - 2022 AN - OPUS4-56389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Seifert, Lando A1 - Ebell, Gino T1 - Abschlussvorstellung Wipano Vorhaben Spanntahlsicherheit N2 - In dem Vortrag werden die Highlights und Ergebnisse des abgeschlossenen Wipano Forschungsprojekts "Spannstahlsicherheit" berichtet. In dem Vorhaben wurde das Projektziel ein neues Prüfverfahren für die Prüfung von Spannstählen auf Spannungsrisskorrosionsempfindlichkeit zu entwickeln erfolgreich abgeschossen. Weiterhin wurden neue Erkenntnisse zu den Ursachen der Ergebnisstreuung der bisherigen Prüfung gemäß ISO 15630-3 gewonnen. Das neue Prüfverfahren soll bei der nächsten Überarbeitungsrunde der ISO 15630-3 als Verfahren zunächst in den informativen Anhang aufgenommen werden. T2 - Arbeitskreissitzung des GfKorr-Arbeitskreises Eisen und Stahl CY - Online meeting DA - 08.12.2022 KW - Korrosion KW - Spannstahl KW - Spannbetonbauwerke KW - Spannungsrisskorrosion KW - Wasserstoffversprödung PY - 2022 AN - OPUS4-56510 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Die Einfügedämmung bei Schienenfahrwegen Definition, Messung und Berechnung N2 - Die Definition und Beschreibung der Einfügedämmung im Normentwurf DIN 45673-4 ist noch nicht richtig. Es wird die Beschreibung aus DIN 45673-3 herangezogen, die für Messungen gilt. Für die drei Rechenverfahren gibt es jeweils eine passende Beschreibung. Mit diesen Vorlagen ist eine vernünftige Definition der Einfügungsdämmung zu finden. Es bedarf einer Abgrenzung gegenüber anderen (falschen) Möglichkeiten. Des Weiteren ist der Anhang 2 erweitert und der Parametersatz im Anhang 1 auf das Wesentliche reduziert worden. T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Online meeting DA - 14.12.2022 KW - Einfügungsdämmung KW - Schienenfahrwege KW - Kraft auf den Boden KW - Erschütterungen im Fernfeld PY - 2022 AN - OPUS4-56601 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Königsbauer, Korbinian A1 - Schaller, M.-B. A1 - Nöther, N. A1 - Wosniok, Aleksander T1 - Entwicklung eines praxistauglichen auf POF basierenden Messsystems mittels digitaler I-OFDR zur Dehnungsdetektion N2 - Es wird ein faseroptisches Messsystem vorgestellt, welches auf Basis der Rayleigh-Rückstreumessung eine ortsauflösende Detektion von signifikant großen Dehnungen bei Bauvorhaben im von Anwendern geforderten Größenordnungsbereich von 3 % bis 10 % ermöglicht. Mit dem Verfahren der digitalen inkohärenten optischen Frequenzbereichsreflek-tometrie (I-OFDR) werden materialspezifische Vorteile robuster perfluorierter polymeroptischer Fasern (PF-POF) erschlossen. Für den angestrebten industriellen Einsatz für die Zustandsüberwachung im Bereich des Tunnel- und Spezialtiefbaus soll die spezifische Rückstreuzunahme in der PF-POF hochauflösend gemessen werden. In diesem Vortrag wird gezeigt, dass sich in ersten Projektergebnissen das digitale I-OFDR für eine Dehnungsdetektion von bis zu 10% eignet. T2 - 21. ITG/GMA-Fachtagung CY - Nuremberg, Germany DA - 10.05.2022 KW - I-OFDR KW - Structure health monitoring KW - Dehnungsdetektion KW - Reyleigh-Rückstreumessung PY - 2022 AN - OPUS4-56717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Königsbauer, Korbinian A1 - Schaller, M.-B. A1 - Nöther, N. A1 - Wosniok, Aleksander T1 - Distributed POF sensors for structural health monitoring in civil construction applications N2 - In this presentation, a cost-efficient distributed fiber optic measurement system based on Rayleigh scattering is shown. The distributed digital incoherent optical frequency domain reflectometry (I-OFDR) method is devel-oped for detection of significantly large strain in the range from 3 % up to 10 % as required by end users. For this purpose, a vector network analyzer used in the I-OFDR is replaced by a compact and costeffective digital data acquisition system. This digital emitting/receiving unit enables the recording of the complex transfer function carrying information about the local deformations along the entire sensing fiber. T2 - POF 2022 The 30th International Conference on Plastic Optical Fibers CY - Bilbao, Spain DA - 26.09.2022 KW - I-OFDR KW - Perfluorinated polymer optical fiber (PF-POF) KW - Strain detection KW - Structural health monitoring. PY - 2022 AN - OPUS4-56714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Korrosion metallener Werkstoffe-Grundlagen N2 - Im Vortrag werden die wesentlichen Grundlagen zum Verständnis der Korrosion metallener Werkstoffe in komprimierter Form vorgestellt. Der Schwerpunkt liegt auf der Betrachtung der atmosphärischen Korrosion und den sich daraus ergebenden Anforderungen an den Korrosionsschutz. T2 - CORPAC Seminar: Wie lassen sich VCI-Korrosionsschutz und Nachhaltigkeit vereinbaren? CY - Weidhausen b. Coburg, Germany DA - 30.03.2022 KW - Einflussgrößen KW - Atmosphärische Korrosion KW - Befeuchtungsdauer PY - 2022 AN - OPUS4-54594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Corrosion of Steel in Concrete and Corrosion Behavior of Stainless Steel N2 - In order to obtain a statement on the corrosion resistance of stainless steel against pitting corrosion, a well-tested measuring arrangement is required. For this purpose, the so-called ECISS test can be used to determine the critical chloride content. This makes it possible to assess the corrosion resistance of various stainless steels that have different chromium contents. T2 - ISO-TC17-SC16-WG13 Expertensitzung CY - Online meeting DA - 11.01.2022 KW - Corrosion KW - Lochkorrosion KW - Chloride induced corrosion KW - Concrete KW - Stainless steel PY - 2022 AN - OPUS4-54239 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Hüllmann, Dino A1 - Winkler, Nicolas P. A1 - Kohlhoff, Harald A1 - Bartholmai, Matthias A1 - Hirschberger, Paul A1 - Bennetts, V. H. A1 - Lilienthal, A. J. T1 - Aerial Robot Olfaction - An Overview of Research @BAM N2 - This presentation gives an introduction to the gas-sensitive aerial robots developed at BAM, including various application examples in the field of mobile robot olfaction: gas source localization, gas distribution mapping, and trial following. T2 - The 6th Meeting of the Investigation Committee on Measurement of Odors and Applications of Their Psychological/Physiological Effects CY - Online meeting DA - 21.01.2022 KW - Mobile Robot Olfaction KW - Gas Tomography KW - Tunable Diode Laser Absorption Spectroscopy (TDLAS) KW - Gas Source Localization KW - Gas Distribution Mapping KW - Trial Following PY - 2022 AN - OPUS4-54241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Die Berechnung der Einfügedämmung bei Schienenfahrwegen – die Impedanzmethode mit einem Freiheitsgrad N2 - Mit dieser Methode kann man die Einfügedämmung eines Schienenstützpunkts/einer Schwelle korrekt berechnen. Sie gilt in ihrer ursprünglichen Form für eine Unterschottermatte in einem Tunnel T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Online meeting DA - 20.1.2022 KW - Impedanzmethode KW - Elastische Elemente KW - Schienenfahrweg PY - 2022 AN - OPUS4-54243 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - Update nach 10 Jahren Bewitterung - Langzeitkorrosionsverhalten nichtrostender Stähle in maritimer Atmosphäre N2 - Durch Fortführung der Untersuchungen aus einem Forschungsvorhaben wurden neun verschiedene Stahllegierungen unter maritimen Umgebungsbedingungen über zehn Jahre ausgelagert und deren Korrosionsverhalten untereinander verglichen und bewertet. Anhand der Ergebnisse der Auslagerungsprüfungen konnten Rückschlüsse auf die Einflüsse der Legierungszusammensetzung, der Oberfächenausführung und der Auslagerungszeit unter maritimen Auslagerungsbedingungen gewonnen werden. Die Proben der drei untersuchten Duplexwerkstoffe zeigten über den Auslagerungszeitraum von zehn Jahren sowohl mit als auch ohne Spaltgeometrie die beste Korrosionsbeständigkeit. Ebenso konnte der molybdänlegierte Ferrit 1.4521 eine vergleichbar gute Korrosonsbeständigkeit erzielen, wie die klassischen austenitischen Werkstoffe 1.4301 und 1.4404. T2 - Korrosionsschutz in der maritimen Technik 2022 CY - Online meeting DA - 27.01.2022 KW - Auslagerungsversuche KW - Korrosionsschutz KW - Korrosion KW - Nichtrostende Stähle PY - 2022 AN - OPUS4-54276 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Monitoring von Strukturverhalten mittels integrierter verteilter faseroptischer Sensorik - Verteilte akustische Sensorik (DAS) N2 - Die verteilte faseroptische akustische Sensorik (DAS) wird vorgestellt, hinsichtlich ihrer Leistungsfähigkeit beschrieben und verschiedenste Anwendungsfelder, z.B. für das Zustandsmonitoring oder für seismische Messungen, beispielhaft gezeigt. Zudem werden mögliche Anwendungsfelder von DAS für den Kontext Kerntechnische Entsorgung (KTE) und Rückbau aufgezeigt. T2 - Online-Workshop „Dauerhafte Verschlussbauwerke für Endlager“ CY - Online meeting DA - 14.02.2022 KW - Verteilte faseroptische Sensorik KW - Verteilte akustische Sensorik KW - DAS KW - KTE KW - Monitoring Endlager PY - 2022 AN - OPUS4-54348 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasch, Thomas A1 - Thomas, Brock A1 - Hesse, Olaf T1 - Assessment Criteria to Evaluate Test Results on Compatibility of Nonmetallic Materials for Oxygen Service Based on BAM’s Safety Philosophy N2 - The general requirement, that nonmetallic materials for oxygen service must be tested and found suitable for their intended use in plants and components is the current state of technical safety. However, numerous requests of manufacturers, sales offices, and users show, that there is still a strong need for information on how these materials are tested and evaluated. Based on more than 60 years of expertise, this paper provides background information on BAM’s test approach. It explains why BAM applies additional assessment criteria on nonmetallic materials for certain use conditions. Hence, the test schedule as well as the final evaluation shall reflect the practical application in a more customer-related way in combination with a higher safety level. That is the demand of BAM’s safety philosophy. T2 - 15th international symposium on flammability and sensitivity of materials in oxygen-enriched atmospheres CY - Online meeting DA - 03.05.2022 KW - Oxygen compatibility KW - Background information on test approaches KW - Evaluation of test results KW - Assessment criteria KW - BAM’s safety philosophy PY - 2022 AN - OPUS4-54887 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Elastische Elemente in der Emission, Transmission und Immission von Bahnerschütterungen N2 - Dieser Vortrag präsentiert einige Prinzipien und einige Beispiele zur Minderung von Eisenbahnerschütterungen. Die Prinzipien unterscheiden sich für die Minderungsmaßnahmen im Gleis, im Boden und bei Gebäuden. Kraftübertragungsfunktionen isolierter und nicht isolierter Gleissysteme, reflektierte und durchgelassene Wellenamplituden bei gefüllten Bodenschlitzen und die Übertragung der Freifeldschwingungen ins Gebäude werden analysiert. Bei den einfachen Gleismodellen muss der richtige Anteil der unabgefederte Fahrzeugmasse zum eindimensionalen Gleismodell hinzugefügt werden. Der Minderungseffekt eines gefüllten Bodenschlitzes ist von der Steifigkeit und nicht von der Impedanz des Schichtmaterials bestimmt. Bei einer elastischen Gebäudelagerung muss die Minderungswirkung mit der richtigen Boden- (Fundament-) Steifigkeit berechnet werden, und das abgeminderte Gebäudeverhalten hängt wesentlich von der effektiven Gebäudemasse ab, die mit zunehmender Frequenz deutlich kleiner als die starre Gebäudemasse ist. T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Bludenz, Austria DA - 17.5.2022 KW - Erschütterungsminderung KW - Bahngleis KW - Bodenschlitz KW - Gebäudelagerung KW - Elastische Elemente PY - 2022 AN - OPUS4-54916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel T1 - Wehrmedizinisches Sonderforschungsvorhaben 29K4 "Primäres Explosionstrauma": „Entwicklung und Validierung eines Körpermodells und eines Stoßwellengenerators zur Simulation der intrakorporalen Stoßwellenausbreitung nach Explosionen“ N2 - Im Rahmen dieses Vortrags wurden aktuelle Arbeiten im Rahmen der Forschungszusammenarbeit mit dem Bundeswehrkrankenhaus Berlin zum primären Explosionstrauma vorgestellt. T2 - 8. KSK Symposium Rüstung 2022 CY - Altensteig/Wart, Germany DA - 13.09.2022 KW - Blast KW - Primäres Explosionstrauma KW - Einsatzkräfte KW - Polizei KW - Körpermodell PY - 2022 AN - OPUS4-55841 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Bewertung von Fallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen N2 - Bericht über die Vorgehensweise der systematischen Untersuchungen zur Entwicklung angepasster Kriterien für die Bewertung von Aufprallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen T2 - AK Prüfstellen CY - Berlin, Germany DA - 21.09.2022 KW - Fallprüfung KW - Aufprallfundament KW - Gefahrgutverpackung KW - Fallfundament KW - Mechanische Sicherheitsprüfung PY - 2022 AN - OPUS4-55842 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Johann, Sergej A1 - Zehn, M. W. T1 - Bewertung von Fallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen N2 - Bericht über die Vorgehensweise der systematischen Untersuchungen zur Entwicklung angepasster Kriterien für die Bewertung von Aufprallfundamenten in der mechanischen Sicherheitsprüfung von Gefahrgutverpackungen T2 - ERFA Verpackungen CY - Berlin, Germany DA - 22.09.2022 KW - Fallprüfung KW - Aufprallfundament KW - Gefahrgutverpackung KW - Fallfundament KW - Mchanische Sicherheitsprüfung PY - 2022 AN - OPUS4-55843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lengas, Nikolaos A1 - Johann, Sergej A1 - Kadoke, Daniel A1 - Müller, Karsten A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel A1 - Zehn, M. W. T1 - Damage assessment of complete, filled fibreboard boxes in regulative vertical impact tests by dropping N2 - Due to the high damping mechanical properties of fibreboard materials, corrugated fibreboard boxes are widely used as transport packages of dangerous goods. Since there is a hazard of vertical impact within the distribution system, drop tests are performed as design type tests to assess the package’s ability to withstand damage. However, there is little information in this context regarding the mechanical response of a filled fibreboard box. This work aims to propose a concept utilizing experimental drop test results by means of finite-element (FE) analyses in order to predict the damage resistance of complete, filled corrugated fibreboard boxes which are ready for transportation. T2 - 38th Danubia Adria Symposium on Advances in Experimental Mechanics CY - Poros Island, Greece DA - 20.09.2022 KW - Drop test KW - Dangerous goods packagings KW - Corrugated fibreboard box KW - Finite-element-analysis KW - Explicit transient simulation KW - Crash simulation PY - 2022 AN - OPUS4-55845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Prestressed Concrete Structures with Concentrated Tendons - Structural Damage due to Hydrogen-Induced Stress Corrosion Cracking N2 - In the course of the deconstruction of the "Bridge of the 20th anniversary of the GDR" at the Altstädter Bahnhof in Brandenburg a. d. Havel, new information on the initiation of hydrogen-induced stress cracks was obtained. BAM was commissioned by the Brandenburg State Road Administration to participate in a corresponding joint project which is financed by the Federal Ministry for Digital and Transport. The added value of the new information gained in this project goes beyond the specific structure. It describes unexpected new damage patterns that can be transferred to other structures with concentrated tendons (tendon block method and Baur-Leonhardt method) and were previously unknown in this form. These should be made known to other developers to enable them to initiate any necessary actions. T2 - Eurocorr 2022 CY - Berlin, Gemany DA - 29.08.2022 KW - Korrosion KW - Corrosion KW - Hydrogen KW - Stress Cracking PY - 2022 AN - OPUS4-55613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fürst, Richard A1 - Häßler, Dustin A1 - Hothan, Sascha T1 - Research Project FIRESTEMIC - Results and Recommendations N2 - The presentation summarizes the results of the research project. T2 - Workshop 2022 - Feuerwiderstand von Stahlzuggliedern mit reaktiver Brandschutzbeschichtung CY - Berlin, Germany DA - 06.09.2022 KW - Fire tests KW - Intumescent coating KW - Steel KW - Tension member PY - 2022 AN - OPUS4-55700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin A1 - Hothan, Sascha A1 - Fürst, Richard T1 - Neue Prüfnorm für reaktive Brandschutzsysteme auf Stahlzuggliedern N2 - Der Vortrag stellt den Entwurf der neuentwickelten Prüfnorm vor. T2 - Workshop 2022 - Feuerwiderstand von Stahlzuggliedern mit reaktiver Brandschutzbeschichtung CY - Berlin, Germany DA - 06.09.2022 KW - Feuerwiderstand KW - Brandschutz KW - Stahlzugglieder KW - Reaktives Brandschutzsystem KW - Prüfnorm PY - 2022 AN - OPUS4-55701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jauregui-Correa, J. C. A1 - Otremba, Frank A1 - Hurtado-Hurtado, G. A1 - Romero-Navarrete, J. A. T1 - Experimental test rig for simulating dynamic loads on subway systems N2 - Degradation in substructures, Mexico’s City Subway. Improve predictions using vibration Measurements. Ability to test operating conditions at Laboratory. Improve previous laboratory rig. Control operating conditions. Produce enough data for evaluating actual conditions. T2 - Fifth International Conference on Railway Technology CY - Montpellier, France DA - 22.08.2022 KW - Test rig KW - Simulating KW - Dynamic loads KW - Subway PY - 2022 AN - OPUS4-55568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Thoralf A1 - Wagner, Adrian A1 - Burkert, Andreas T1 - Field exposure studies of austenitic and duplex stainless steels in tunnel atmospheres N2 - Due to the high corrosivity that are present in road tunnel structures, cleaning and maintenance work on stainless steel components in the tunnels is carried out at regular intervals in the tunnels, which means that parts of the lanes or the whole tunnel have to be temporarily closed. To reduce these traffic disruptions and maintenance costs, it is important to reduce the work that is needed for cleaning and maintenance of stainless steel components in road tunnels. One possibility is the identification and utilization of better suited alternatives to the commonly used austenitic stainless steels AISI 316L and AISI 316Ti. Thus, a field exposure study was carried out in different road tunnels throughout Germany to qualify different duplex and lean duplex stainless steels for tunnel constructions. The proposed scientific poster gives an overview of results after the first three years of exposure in three different road tunnels. Samples of different stainless steels were placed in different areas of the tunnel – at lane height and at the ceiling. Some samples were exposed under sheltered conditions. Pit depths were evaluated on the free surface and in crevice areas after each year of exposure. The investigations show that duplex stainless steels have a comparable or even better corrosion resistance than austenitic steels in tunnel atmospheres. T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Corrosion KW - Atmosphere KW - Tunnel KW - Stainless Steel PY - 2022 AN - OPUS4-55595 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moye, Janis A1 - Sturm, Patrick A1 - Kühne, H.-C. A1 - Keßler, S. A1 - Pistol, K. T1 - Entwicklung und Charakterisierung von alkalisch aktivierten Mörteln für die Betoninstandsetzung - Robustheits- und Dauerhaftigkeitsbetrachtungen N2 - Für die flächige Instandsetzung von Stahlbetonkonstruktionen kommen nahezu ausschließlich zementgebundene Systeme mit hohem Zementgehalt zum Einsatz (1). Bereits 2008 war die Zementproduktion für 5% des weltweiten, anthropogenen CO2-Ausstoßes verantwortlich (2). Um die prozessbedingten CO2-Emissionen zu senken, wird der Zement bereits durch gewisse Mengen an Sekundärrohstoffen wie Flugasche, Silicastaub oder Hüttensandmehl (Hochofenschlacke) substituiert. Das Potenzial für weitere Modifikationen ist inzwischen begrenzt (3). Zudem ist eine hohe Lebensdauer der Konstruktionen in vielen Anwendungsbereichen nur bedingt realisierbar. Spätestens mit Erreichen der geplanten Nutzungsdauer müssen Stahlbetonkonstruktionen mit zementgebundenen Systemen instandgesetzt werden, was im ökonomischen und ökologischen Sinne keine nachhaltige Lösung darstellt. Die Verwendung neuer Baustoffe wie alkalisch aktivierte Mörtel hält sich bisher in Grenzen (4), sodass die Akzeptanz durch praxisnahe Forschung adressiert werden muss. Vorangegangene Forschungsergebnisse zeigen, dass alkalisch aktivierte Bindemittel vielversprechende technische Eigenschaften besitzen. So zeigen sich im Vergleich zu herkömmlichem Portlandzement ein ausgesprochen wirkungsvoller Verbund zu Stahl und Zementmörtel (5), (6), eine hohe chemische Beständigkeit sowie ein Erfolg versprechendes Abwitterungsverhalten bei Frost-Tau-Wechseln (7). Mit diesen Eigenschaften können alkalisch aktivierte Mörtel einen erheblichen Beitrag zur dauerhaften Betoninstandsetzung leisten und somit durch die verringerten CO2-Emmissionen dem Prinzip des nachhaltigen Bauens gerecht werden. Wichtig für die Produktion im größeren Maßstab ist die Verfügbarkeit der möglichen Reststoffe, um eine CO2-positivere Bilanz abzubilden. Im Zuge des Forschungsvorhabens sollen Rezepturen für Instandsetzungsprodukte entworfen werden, die auf alkalisch aktivierte industrielle Reststoffe zurückgreifen und die Anforderungen an konventionelle Instandsetzungsprodukte erfüllen. Hierzu wurden potenzielle Ausgangs-stoffe mit Natriumcarbonat aktiviert und die Verarbeitbarkeit der Leime sowie die Druckfestigkeiten nach sieben Tagen verglichen. Hüttensandmehl reagiert ausreichend mit diesem Aktivator, was sich mit Ergebnissen von (8) und (9) deckt. Es werden 〖CO〗_3^(2-)-Ionen in das System eingebaut, was zu einer anfänglichen Erstarrung des Gefüges durch die Bildung von Carbonaten (Calcit und Hydrotalcit) führt. Nach einer längeren dormanten Phase bilden sich zusätzlich Hydratphasen, die die Festigkeit weiter erhöhen. Weiterhin ist die chemische Zusammensetzung der Schlacken für die Erhärtung und die späteren Eigenschaften von großer Bedeutung (10), (11), was mit einer Parameterstudie im laufenden Jahr an natriumcarbonataktivierten Schlacken näher betrachtet werden soll. Erkenntnisse aus vergleichenden Versuchen durch (12) bestätigen die Einflussnahme der chemischen Zusammensetzung. Die übrigen Reststoffe konnten mit anderen Aktivatoren (z. B. Natriumsilicat und -hydroxid) zu einer Reaktion angeregt werden. Im Hinblick auf die Akzeptanz der alkalisch aktivierten Bindemittel stellen diese Aktivatoren jedoch bei der Herstellung höhere technische Anforderungen an das Personal und die verwendeten Geräte im Vergleich zur konventionellen Beton- und Mörteltechnik. Die Aktivierung mittels Alkalicarbonaten ermöglicht die Herstellung von Beton bzw. Mörtel nach dem üblichen „just add water“-Prinzip (13). Aktuell wird unter Einbindung einer studentischen Abschlussarbeit eine Rezeptur mit Hüttensandmehl hinsichtlich der Frisch- und Festeigenschaften charakterisiert und einer Referenzmischung – basierend auf Portlandzement – gegenübergestellt. Hieraus resultierende Ergebnisse sollen neben den Erkenntnissen aus den Vorversuchen zur Konferenz vorgestellt und ein Ausblick auf die weitere Forschungsarbeit gegeben werden. T2 - Nachwuchswissenschaftler*innenkonferenz 2022 CY - Brandenburg an der Havel, Germany DA - 11.05.2022 KW - Alternative Bindemittel KW - Alkalische Aktivierung KW - Instandsetzung KW - Realkalisierung PY - 2022 AN - OPUS4-55517 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Potential Mapping - What could we measure and what should we able to detect – guideline B03 of DGZfP N2 - “Electrochemical potential mapping according to guideline B3 of DGZfP (German Society for Non-Destructive Testing) is a recognized technique for the localization of corroding reinforcing steels. Areas of corroding reinforcement steel can be located in a non-destructive manner by means of this procedure. Half‐cell potential measurements are used in order to detect chloride‐induced corrosion. However, it is not recommended in order to assess the risk of carbonation‐induced corrosion. For this purpose, determining the carbonation depth and the concrete cover appears more appropriate. The content of this specification exclusively refers to the application of mobile, local variable reference electrodes, which are only placed on the concrete surface while measuring. The technique distinguishes itself thereby from the range of corrosion monitoring systems with stationary installed reference electrodes and sensor systems, respectively, whereby it is possible to continuously track measurements within the area of the installed electrodes. However, these methods are not dealt with in this specification.” T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Korrosion KW - Potentialfeldmessung KW - Corrosion KW - Half-cell potential KW - Potential mapping PY - 2022 AN - OPUS4-55524 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, S. A1 - Algernon, D. A1 - Arndt, R. A1 - Ebell, Gino A1 - Friese, M. A1 - Grosse, C. U. A1 - Holstein, R. A1 - Niederleithiger, Ernst A1 - Schickert, M. A1 - Schulze, S. A1 - Taffe, A. A1 - Walther, A. A1 - Wolf, J. A1 - Zoega, A. A1 - Zwanzig, M. T1 - Introduction to DIN 4871: Qualification of NDT Personnel in Civil Engineering (NDT‐CE) N2 - Recently, non-destructive testing in civil engineering (NDT-CE), in particular of concrete components, has successfully mastered the leap from research to practice. Several methods have been established for field inspections to determine the concrete cover of reinforcement or to estimate the compressive strength as well as other parameters related to the concrete material. In addition, the application of non-destructive testing is indispensable, if information about the inner structure - such as the location of rebars and tendon ducts or the damage-related condition assessment to detect grouting defects, honeycombs, delamination, or corrosion - is required. Besides the selection of a suitable NDT method and an appropriate inspection system, the reliability of the results depends largely on the person who applies the non-destructive inspection technique and evaluates the inspection results. To ensure a high quality of non-destructive concrete evaluation as well as to keep the uncertainty caused by the inspection personnel to a minimum, structured, consistent, and regulated theoretical as well as practical training of inspection personnel is essential. To close this gap, the subcommittee of education and training (UA-A) within the committee for NDT-CE of the German Society for Non-Destructive Testing (DGZfP) has been reactivated in 2018 to establish uniform training standards for non-destructive concrete inspections in the long term. The subcommittee consists of scientists, practitioners, authorities, and clients. So far, the national standard DIN 4871 “Non-destructive testing - Qualification of NDT personnel in Civil Engineering (NDT-CE)” was developed. This standard considers the civil-industry-specifics, for example, that standards for NDT of concrete, as well as related product standards with a few exceptions, still do not exist at the moment. Within this presentation, the concept, the connection to ISO 9712 and other standards as well as an overview of the recently developed German standard DIN 4871 will be presented. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Non-destrucive testing KW - Civil engineering PY - 2022 AN - OPUS4-55526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, W. A1 - Wilsch, Gerd A1 - Katsumi, N. A1 - Ebell, Gino A1 - Völker, Tobias T1 - Ion distribution in concrete overlay, mapped by laser induced breakdown spectroscopy (LIBS), modified by an embedded zinc anode N2 - Galvanic corrosion protection by embedded zinc anodes is an accepted technique for the corrosion protection of reinforcing steel in concrete. Galvanic currents flow between the zinc anode and the steel reinforcement due to the potential difference that is in the range of a few hundred mV. The ion distribution was studied on two steel reinforced concrete specimens admixed with 3 wt.% chloride/wt. cement and galvanically protected by a surface applied EZ-anode. On both specimens, a zinc anode was embedded and glued to the concrete surface by a geo-polymer-based chloride-free binder. At one specimen, the EZ-anode was operated for 2,5 years, the EZ-anode at the other specimen was not electrically connected to the reinforcement, this specimen serves as a reference. Both specimens have been stored under identical conditions. The ion distribution between the anode (EZ-anode) and cathode (steel reinforcement) was studied by laser-induced breakdown spectroscopy (LIBS) after 7 months, 12 months, and 2,5 years. Results of the LIBS studies on the specimen with activated EZ-anode after 7 months, 12 months, and 2,5 years and of the reference specimen after 2,5 years are reported. Results show that diffusion of ions contributes to the changes in the ion distribution but migration, especially of chlorides towards the EZ-anode is significant despite the weak electric field – several hundred millivolts - generated by the galvanic current. Results show that chloride ions accumulate near the zinc-anode as in water-insoluble zinc-hydroxy chlorides - Simonkolleit. T2 - ICCRRR 2022 CY - Capetown, South Africa DA - 03.10.2022 KW - Korrosion KW - Corrosion KW - LIBS KW - Zinc PY - 2022 AN - OPUS4-55948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klimek, André A1 - Stelzner, Ludwig T1 - Screening-tests on the susceptibility to spalling of two ordinary concretes N2 - Investigating the spalling behaviour of a concrete mixture using large scale members is complex and expensive. Thus, the susceptibility of concrete to spalling is investigated by means of fire tests on small scale specimens. However, the reduction of the fire exposed surface increases the influence of boundary effects. Macrocracking and the water loss via the lateral surfaces reduce the impact of the thermomechanical and thermohydraulic damage mechanisms and therefore, lower the risk of spalling. Thus, the influence of different restraints on the spalling behaviour of intermediate scaled specimens (Ø0.47 m; h=0.29 m) was investigated for two ordinary concrete mixtures. Both mixtures had the same composition except the type of aggregate. One mixture contained only quartzitic aggregates, whereas the other mixture was made with basalt grit as coarse aggregates. Applied steel rings restrained the thermal expansion of the specimen and prevented the loss of water, whereas applied steel sheet primarily reduced the loss of water during the fire test. Additionally, the fire exposed surface of one specimen of each mixture was pre-dried under controlled climate conditions and fire tested with applied steel rings. The results show a higher spalling volume for the ring restrained specimens compared to the other covering types. Further, the pre-dried boundary zone leads to delayed and decreased occurrence of spalling compared to the non-dried specimens for the concrete with quartzitic aggregates and to a prevention of spalling for the mixture with basalt aggregates. Additionally, the results show that the influence of the thermomechanical behaviour of the coarse aggregates increases with increasing restraint. The restrained conditions of the specimens with applied steel ring are comparable to the conditions in the centre of a large scale member. This test series is a further step for possible concept of steel ring restraint concrete specimens as “screening-tests” in upcoming projects. T2 - 7th International Workshop on Concrete Spalling due to Fire Exposure CY - Berlin, Germany DA - 12.10.2022 KW - Spalling KW - Fire test KW - Concrete KW - Restraint PY - 2022 AN - OPUS4-56023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst A1 - Hindersmann, I. A1 - Sodeikat, C. A1 - Groschup, R. T1 - Monitoring of a German Road Bridge Using Embedded Ultrasonic Transducers and Coda Waves N2 - The ‘G¨anstorbr¨ucke’ bridge between the cities of Ulm and Neu-Ulm is one of the best-monitored bridges all over Germany. In addition to an already active bride monitoring system, we have equipped the bridge with 30 ultrasonic transducers to explore the monitoring possibilities at an in-service large-scale reinforced concrete structure with continuous active ultrasonic measurements. The monitoring system is based on the detection of small changes in the entire signal, especially the multiply scattered parts of the recording, the so-called coda. Applying Coda Wave Interferometry (CWI), subtle changes in the signal can be detected and related to changing velocities in the area between source and receiver. A comparison of the results from coda wave interferometry with the strain measurements of the permanent monitoring system shows a correlation between strain measurements and CWI results. We discuss the challenges of changing environmental conditions, pose for interpretation of the results, and highlight the advantages of embedded versus externally attached ultrasonic transducers in permanent bridge monitoring, especially when coda wave interferometry is applied. T2 - EWSHM 2022 CY - Palermo, Italy DA - 04.07.2022 KW - Bridge monitoring KW - Ultrasound KW - Embedded sensors KW - Coda wave interferometry PY - 2022 AN - OPUS4-55383 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Ebell, Gino T1 - Safety of Prestressing Steels N2 - This talk reports the findings of the WIPANO "Knowledge and Technology Transfer via Patents and Standards" research project "Safety of Prestressing Steels," founded by the German Ministry of Economic Affairs and Climate Action (BMWK). A new test method for assessing the susceptibility of prestressing steels to hydrogen-induced stress corrosion cracking (SCC) is presented, which serves the demands of a lower scattering compared with the present standard. Moreover, the ability to differentiate between high susceptible and low susceptible prestressed wires is possible, modifying the method by hydrogen charging and surface preparation. T2 - Konferenz EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - ISO 15630-3 KW - Stress Corrosion Cracking KW - Prestressing Steels KW - Hydrogen KW - Constant Load Test PY - 2022 AN - OPUS4-55661 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Neue Erkenntnisse zu wasserstoffinduzierten Spannungsrissen infolge korrosiver Belastung hochempfindlicher Spannstähle in Spannblockverfahren nach TGL 173-33 N2 - Brückenbauwerke, die im Spannblockverfahren hergestellt wurden, können bauartbedingt wasserstoffinduzierte Spannungsrisse über den gesamten Querschnitt eines Spannkanals aufweisen. Das Risswachstum kann infolge dynamischer Beanspruchung über die Nutzungsdauer fortschreiten und zu Spanndrahtbrüchen führen. T2 - 5. Brückenkoloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Korrosion KW - Spannungsrisskorrosion KW - Brücke KW - Wasserstoff PY - 2022 AN - OPUS4-55663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Schmidt, Sebastian A1 - Steinbock, Oliver T1 - B1 - Brücke am Altstädter Bahnhof in Brandenburg an der Havel - Detektion von Spanndrahtbrüchen mit Schallemissionsanalyse N2 - Bei einer turnusmäßigen Inspektion der B1 Brücke am Altstädter Bahnhof in Brandenburg an der Havel wurden im Dezember 2019 Risse und Hohlstellen entlang der Längsträger festgestellt. Als Ursache wurde das Versagen eines signifikanten Anteils der Spanndrähte der konzentrierten Spannglieder vermutet. Die Brücke wurde umgehend für den Verkehr gesperrt und nach weiteren, umfassenden Untersuchungen im Mai 2021 abgebrochen. Um die Sicherheit des unter der Brücke geführten Verkehrs zu gewährleisten, wurde die Brücke unter anderem mit einem Schallemissionsmesssystem überwacht. Mit diesem Verfahren ist es möglich, Spanndrahtbrüche zuverlässig zu detektieren und zu lokalisieren. In dem gut einjährigen Überwachungszeitraum wurden mehr als einhundert Spanndrahtbrüche detektiert, die in einigen Bereichen der Brücke besonders konzentriert auftraten. Vor dem Abbruch der Brücke war es möglich, den Nachweis der Detektion von Spanndrahtbrüchen mit der Schallemissionsanalyse und ihre Ortungsgenauigkeit anhand von künstlich erzeugten Drahtbrüchen zu validieren. Weiterhin konnte das sichtbare Schadensbild, Längsrisse und Hohlstellen über den Spannkanälen, auf die lokale Schädigung der Spanndrähte zurückgeführt werden. Derzeit wird ein Merkblatt erarbeitet, in dem die Erfahrungen in der bisherigen Anwendung der Schallemissionsanalyse zum Monitoring von Spanndrahtbrüchen zusammengefasst werden. In diesem Beitrag werden die Grundlagen der Schallemissionsanalyse und die Ergebnisse der Validierungsversuche an der Brücke in Brandenburg dargestellt. Weiterhin werden die Vorteile und Grenzen der Brückenüberwachung mittels Schallemissionsanalyse sowie Maßnahmen zur Sicherstellung der Qualität und der Zuverlässigkeit diskutiert. T2 - 5. Brückenkolloquium CY - Esslingen, Germany DA - 05.09.2022 KW - Spannbetonbrücke KW - Spannstahlbruch KW - Schallemission KW - Fotogrammetrie KW - Faseroptik PY - 2022 AN - OPUS4-55686 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin T1 - Distributed fiber optic sensing @BAM N2 - Research and developement activities of BAM regarding Distributed Fiber Optic Sensing are portrayed using exemplary previous and current projects. Shown results pertain to distributed acoustic sensing (DAS), distributed temperagture sensing (DTS) and distributed strain sensing (DSS). T2 - Seismic seminar FU Berlin (group Prof. Shapiro) CY - Online meeting DA - 15.09.2022 KW - Distributed fiber optic sensing KW - Distributed acoustic sensing KW - Distributed temperature sensing KW - Distributed strain sensing KW - Infrastructure monitoring PY - 2022 AN - OPUS4-55721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fürst, Richard A1 - Häßler, Dustin A1 - Hothan, Sascha T1 - European test standard for intumescent coatings applied to steel tension bars with solid section N2 - Description of the FIRESTEMIC project and the newly developed test standard for reactive fire protection systems on steel tension members. T2 - Symposium 2022 Heißbemessung - Structural Fire Engineering CY - Brunswick, Germany DA - 13.09.2022 KW - Fire tests KW - Tension member KW - Intumescent coating KW - Steel KW - Test standard PY - 2022 AN - OPUS4-55702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kremberg, Jan A1 - Häßler, Dustin A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Brandversuche an mechanisch belasteten Carbonzuggliedern N2 - Präsentation zu den Ergebnissen des Forschungsprojektes NeZuCa. T2 - 8th Symposium Structural Fire Engineering CY - Brunswick, Germany DA - 13.09.2022 KW - Carbon KW - Brandschutz KW - Feuerwiderstand KW - Brandversuch KW - Zugglied PY - 2022 AN - OPUS4-55705 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Zündgefahren durch Funken – Grundlagen und Maßnahmen zum Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm DIN EN ISO 80079-36:2016 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. VA22-00800) ; Außeninstitut der RWTH Aachen CY - Lübeck, Germany DA - 09.08.2022 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanischer Explosionsschutz KW - Nichtelektrischer Explosionsschutz PY - 2022 AN - OPUS4-55483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Geophysical methods delivering input to geostatistical methods for geotechnical site characterization N2 - Geophysical methods are able to contribute significantly to geotechnical site characterization. In-situ parameters are collected and gaps between boreholes or other direct tests are filled with information. However the limited resolution has to be considered and the indirect geophysical parameters have to be translated into something geotechnically useful. Moreover, the limitations have to be evaluated when including geophysical data into geostatistical models. If done properly, the use of geophysics will help in an efficient and effective site characterization. A comprehensive overview on existing geophysical (mostly seismic) methods is given as well as information on the calibration of geophysical against geotechnical parameters, pitfalls and limitations and some hints how to include these data into geostatistical/geotechnical models. T2 - ICGoES International Conference on Geologicalk Engineering and Geosciences CY - Yogyakarta, Indonesia DA - 21.09.2022 KW - Geophysics KW - Geostatistics KW - Geotechnics PY - 2022 AN - OPUS4-55806 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John T1 - Fließeigenschaften von festen Gefahrgütern - Vergleich der Messung des Schüttwinkels und der Bestimmung des Hausner-Faktors N2 - Fazit: Nachteile der Schüttwinkel-Messmethoden: Einschränkungen bei der Anwendbarkeit auf Füllgüter mit bestimmten Eigenschaften; Die einzelnen Methoden liefern dann unterschiedliche Ergebnisse (statist. signifikante Abweichung der Mittelwerte); Schlechte Wiederholbarkeit; Bedienereinfluss spielt Rolle; Gewährleistung des Arbeitsschutzes schwierig; Bestimmung des Hausner-Faktors: Keins dieser Defizite Mögliche Abhilfemaßnahmen: Prüfbericht und Zulassungsschein sollten zumindest die Methode angeben, die zur Messung des Schüttwinkels 𝛼 eingesetzt wurde; Einheitliches Verfahren zur Schüttwinkelmessung (DIN-Methode)? Umstellung des Systems auf einen alternativen Parameter zur Bestimmung der Fließeigenschaften: Hausner-Faktor 𝐻: Bessere Wiederholbarkeit der Ergebnisse; Zuverlässige Anwendbarkeit auch auf Extremfälle von Schüttgütern; Sicherere Handhabung von Gefahrgütern T2 - 35. Sitzung des BAM AK Prüfstellen CY - Berlin, Germany DA - 21.09.2022 KW - Gefahrgutverpackungen KW - Schüttwinkel KW - Hausner-Faktor KW - Pulver PY - 2022 AN - OPUS4-55810 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino T1 - Das B 03 - Merkblatt - Übersicht N2 - Der Vortrag gibt eine Übersicht zu den Inhalten des B03 Merkblattes zur Potentialfeldmessung mit praktischen Anwendertipps. T2 - Lehrgang zum Erwerb des Sachkundenachweises zur Durchführung von Potentialfeldmessungen CY - Aachen, Germany DA - 12.09.2022 KW - Potentialfeldmessung KW - Korrosion KW - Stahlbeton KW - Spannbeton PY - 2022 AN - OPUS4-55726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klimek, André A1 - Stelzner, Ludwig A1 - Hothan, Sascha T1 - Auswirkung von passivem Zwang auf das Abplatzverhalten von Beton im Brandfall N2 - Beschreibung des Abplatzverhaltens von vier Prüfkörpertypen in Abhängigkeit der Ummantelungsart und Lagerungsbedingungen für zwei Betonrezepturen T2 - 8th Symposium Structural Fire Engineering CY - Brunswick, Germany DA - 13.09.2022 KW - Brand KW - Beton KW - Abplatzen KW - Zwang PY - 2022 AN - OPUS4-55734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fladt, Matthias A1 - Weise, Frank T1 - Internal water-repellent treatment – a novel strategy for mitigating alkali-aggregate reaction in concrete pavements N2 - To prevent future alkali-aggregate reaction (AAR) damage, which has occurred frequently in the German highway network in recent years, a new regulation has been drafted. This regulation severely limits the use of alkali-sensitive aggregates by requiring that their suitability be verified by certified inspectors using newly developed AAR concrete tests that involve the external supply of alkali. This has led to a significant limitation in the number of aggregates usable for concrete pavements. A novel AAR avoidance strategy is now being pursued, which aims to enable the use of borderline alkali-sensitive aggregates through the application of an internal water-repellent treatment. The addition of water repellents during concrete production should significantly reduce the ingress of water and external de-icing salts into the concrete pavement, thus reducing the potential for AAR damage. This paper presents the results of laboratory tests to assess the suitability of this new AAR prevention strategy. Representative, highly AAR-susceptible road paving concrete made with an alkali-sensitive greywacke and various water repellents were used as the basis for these experiments. The tests for concrete suitability included determining the conventional fresh and hardened concrete properties as well as concrete prism tests with external alkaline supply. Building on these results, laser-induced breakdown spectroscopy (LIBS) analyses of de-icing-salt intrusion as well as microscopic examinations for verification of the AAR characteristics were carried out. The results of the AAR concrete tests with external alkaline supply support the conclusion that, when hydrophobic agents containing a suitable active ingredient are used, the AAR damage process in road paving concrete can be sufficiently prevented. T2 - 16th International Conference on Alkali-Aggregate Reaction in Concrete CY - Lisboa, Portugal DA - 31.05.2022 KW - Concrete pavements KW - Internal water-repellent treatment KW - Preventive measures KW - Testing for potential AAR PY - 2022 AN - OPUS4-56870 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grohmann, Maria A1 - Niederleithinger, Ernst T1 - Anwendung der Reverse-Time Migration auf Ultraschall-Echo-Daten in der zerstörungsfreien Prüfung von Betonbauteilen N2 - Das Ultraschall-Echo-Verfahren ist eine klassische zerstörungsfreie Prüftechnik zur Geometriebestimmung sowie Schadensanalyse von Betonkonstruktionen. Um die Abbildung der Ultraschalldaten von komplexen Betonstrukturen zu verbessern, haben wir die Reverse-Time Migration (RTM) aus der Seismik auf die zerstörungsfreie Prüfung im Bauwesen übertragen. In einer Vorstudie haben wir einen 2D akustischen RTM Code verwendet und an realen Ultraschalldaten, die an einer Betonfundamentplatte aufgenommen wurden, getestet. Im Vergleich mit dem herkömmlichen Rekonstruktionsalgorithmus für Ultraschalldaten, der Synthetic Aperture Focusing Technique (SAFT), zeigten die akustischen RTM-Ergebnisse eine deutliche Verbesserung in der Abbildung der inneren Struktur der Betonfundamentplatte. Vertikale Reflektoren konnten rekonstruiert werden, was mit dem herkömmlichen Abbildungsverfahren nicht möglich war. RTM ist, im Gegensatz zu SAFT, eine wellengleichungsbasierte Migrationsmethode und beruht auf der numerischen Lösung der vollständigen Wellengleichung. Die Vorteile sind, dass der Algorithmus sämtliche Informationen des Wellenfeldes verwendet und daher verschiedene Welleneffekte wie z.B. Multipathing berücksichtigt werden können. Die RTM bietet damit die Möglichkeit auch stark geneigte Reflektoren sowie Streukörper mit komplexen Geometrien darzustellen. Ein Nachteil ist jedoch die lange Rechenzeit und der hohe Bedarf an Speicherkapazität. Ein RTM-Algorithmus, der die elastische Wellengleichung anstatt der akustischen verwendet (wie in unserer Vorstudie angewandt), hat das Potenzial, die Abbildungsergebnisse noch weiter zu optimieren. Das liegt daran, dass unsere Ultraschallmessdaten durch Anregung elastischer Wellen generiert werden. In einem ersten Schritt haben wir zwei elastische 2D-RTM-Algorithmen an synthetischen Ultraschalldaten getestet. Diese wurden mit einem Betonmodell, bestehend aus mehreren Stufen und kreisförmigen Lufteinschlüssen, erzeugt. In einem zweiten Schritt wurden reale Ultraschalldaten mit Scherwellenprüfköpfen an einer Betonstufenplatte mit integrierten Hüllrohren aufgenommen. Die Auswertung der realen Daten mit unserem elastischen RTM-Code war ebenfalls erfolgreich. Wir konnten die Abbildungsqualität der Stufen und Hüllrohre im Vergleich zur akustischen RTM und SAFT verbessern. T2 - Tagung Deutsche Geophysikalische Gesellschaft DGG CY - Munich, Germany DA - 07.03.2022 KW - Ultraschall-Echo-Verfahren KW - Reverse Time Migration KW - Synthetic Aperture Focusing Technique PY - 2022 AN - OPUS4-56112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Hicke, Konstantin A1 - Bernauer, F. A1 - Igel, H. A1 - Hadziioannou, C. T1 - Multi-Sensor measurements on a large-scale bridge model N2 - This contribution introduces an investigation of a large-scale prestressed concrete bridge model (“BLEIB” structure at the BAM-TTS open air test site) by means of on-site cooperative measurements. This bridge has an external post-tensioning system and has been instrumented with the ultrasonic transducers, temperature sensors and optical fibers for Distributed Acoustic Sensing (DAS). Our experiment was designed to test the suitability of the novel 6C sensors developed within the framework of the GIOTTO project – the IMU50. The IMU50 sensor enables vibration measurements in translation along three axes and rotation around three axes. The geophone sensors were considered for complementary measurements of vertical velocity response. In the experiment, several perturbations were achieved by controlling the external influence factors such as loading and prestressing changes. The aim of the integrated measurement strategy was to fully observe the results of the condition change and to verify the effectiveness of multiple sensors for bridge monitoring. T2 - 5. Brückenkolloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Concrete KW - Bridge KW - Monitoring KW - Rotation KW - Distributed acoustic sensing PY - 2022 AN - OPUS4-55626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Zerstörungsfreie Prüfung von Fundamenten vor der Wiedernutzung N2 - Für die Qualitätssicherung von neuen Fundamenten steht eine Reihe von zerstörungsfreien Prüfverfahren zur Verfügung. Das Portfolio reicht von der einfachen Hammerschlagmethode („Pfahlintegritätsprüfung“) bis zu aufwändigen Ultraschallverfahren für meterstarke Fundamentplatten. Aber funktionieren die Verfahren auch im Bestand? Lassen sich die für Wieder-, Um- und Weiternutzung notwendigen Daten erfassen? Und wie werden die zerstörungsfreien Prüfverfahren erfolgreich in Untersuchungskonzepte integriert? Dies wird vor allem am Beispiel der Fundamente von Freileitungsmasten diskutiert. T2 - RWTH Forum Geotechnik CY - Online meeting DA - 20.1.2022 KW - Fundamente KW - Wiedernutzung KW - Zerstörungsfreie Prüfung KW - Parallelseismik KW - Pfahlgründung PY - 2022 AN - OPUS4-54236 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Niederleithinger, Ernst A1 - Fontoura Barroso, Daniel T1 - Coda Wave Interferometry for Monitoring Bridges with Embedded Ultrasonic Transducers – Lessons Learned at the Gänstorbrücke Bridge Ulm, Germany N2 - Ultrasonic Coda Wave interferometry has the potential to detect minute changes in scattering materials like concrete. By permanently installing ultrasonic transducers in concrete, DFG Research unit CoDA aims to develop methods for concrete damage assessment in Germany's aging infrastructure. To test the methods developed in simulations and laboratory experiments on a large scale, we have implemented several ultrasonic transducers at the Gänstorbrücke Ulm, one of Germany's most monitored road bridges. Since fall 2020 we are monitoring parts of the center of the Bridge, as well as an abutment, and compare the results to the commercial monitoring system. All data is recorded with a self-made data collection device, the so-called W-Box, and analyzed with different coda wave-based algorithms to detect signal and volumetric velocity changes. The long-term measurements show that the influence of temperature changes on strains and therefore ultrasound velocity changes calculated with coda waves can be monitored. The capabilities and limitations of the coda wave-based monitoring system are tested in a controlled experiment. Static loading using a truck with varying loads at several positions allows the calibration of the system to improve the detectability of possibly damaging loads and changes induced by this loading. A map of velocity change analyzing data from this load experiment shows that the influence of load on the material and strain distribution can be detected with array measurements. T2 - NDT-CE 2022 - The International Symposium on Nondestructive Testing in Civil Engineering CY - Zurich, Switzerland DA - 16.08.2022 KW - Coda Wave Interferometry KW - Ultrasound KW - Embedded sensors KW - Bridge Monitoring KW - Load Experiment PY - 2022 AN - OPUS4-56454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Niederleithinger, Ernst A1 - Epple, Niklas A1 - Liao, Chun-Man T1 - Recent advances in (ultra)sonic active and passive monitoring of reinforced and prestressed concrete structures N2 - In addition to already established structural monitoring methods such as deformation, inclination or strain gauges or acoustic emission sensors, sonic or ultrasonic monitoring might provide valuable information about the condition or alteration of a structure. Sensors such as geophones, recording ambient noise in the sonic and subsonic frequency range can provide information beyond modal analysis by using interferometric methods. Wave velocities determined by this method are related to the elastic properties and stiffness of material and structure and can be converted into damage indicators. Embedded active ultrasonic transducer networks can provide more detailed insight about deterioration or damages again, using interferometric technologies. This approach is extremely sensible, detecting relative change in velocity on down to 10-5. These methods, including benefits and remaining challenges, are demonstrated using data from a test structure at BAM’s test site demonstrating the case of prestress loss, and data from an actual bridge still under traffic. T2 - International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Monitoring KW - Ultrasonic KW - Non-destructive testing KW - Coda wave KW - Bridge PY - 2022 AN - OPUS4-56000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Guangliang, Y. A1 - Mahon, D. A1 - Gardner, S. T1 - Muon tomography applied to assessment of concrete structures: First experiments and simulations. N2 - Non-destructive techniques for reinforced or prestressed concrete inspection such as ultrasound or radar have found regular, successful practical application but sometimes suffer from limited resolution and accuracy, imaging artefacts or restrictions in detecting certain features. Until the 1980s X-ray transmission was used in case of special demands and showed a much better resolution than other NDT techniques. However, due to safety concerns and cost issues, this method is almost never used anymore. Muon tomography has received much attention recently. Novel detectors for cosmic muons and tomographic imaging algorithms have opened new fields of application. As a first step towards practical application in civil engineering and as a proof of concept we used an existing system to image the interior of a reference reinforced 600 kg concrete block. Even with a yet not optimized setup for this kind of investigation, the muon imaging results are at least of similar quality compared to ultrasonic and radar imaging, potentially even better. In a second step, we have performed simulations to assess the potential for a set of important testing problems such as grouting defects in tendon ducts. The next steps include the development of mobile detectors and optimizing acquisition and imaging parameters. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Muon tomography KW - Concrete KW - Inspection KW - Simulation PY - 2022 AN - OPUS4-56323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Bernauer, F. A1 - Igel, H. A1 - Hadziioannou, C. T1 - Real time bridge monitoring using ultrasonic techniques combined with six component (6-c) measurements N2 - This study aims to develop a real-time monitoring method for the structural performance by ultrasonic testing in combination with six-component (6-C) translation and rotation measurements. So far, the recordings of the velocity and acceleration response in the translation direction have been used to obtain the eigenfrequencies of structures. Recently, measurement of rotation has been used to fully characterize the dynamic behavior of structures. In this research, 6-C sensors consisting of a three-component rotational seismometer and a three-component broadband seismometer are evaluated for their suitability for bridge monitoring. Since changes in environmental conditions such as temperature during vibration recordings affect the structural evaluation results, cross-correlation function is applied here to the 6-C ambient vibration signals to reconstruct the wave propagation on the one hand, and coda wave interferometry (CWI) is applied to obtain the internal velocity variation from waveforms on the other hand. In field tests on a large-scale prestressed concrete bridge model, it was verified whether the prestress loss can also be determined in presence of temperature effects. For this purpose, measurements were performed in two scales, ultrasonic and output-only vibration measurements. The change in structural properties due to the prestress loss should be detected by the pulse velocity change. The results demonstrate both the performance and advantages of ultrasonic techniques and the capabilities of 6-C sensors. Thus, the application of CWI to wave signals can contribute comprehensively to bridge monitoring. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - 6-C vibration signals KW - Coda wave interferometry KW - Cross-correlation function KW - Prestressed bridge KW - Structural health monitoring KW - Ultrasonic PY - 2022 AN - OPUS4-55646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Günzel, Stephan A1 - Bock, Robert T1 - The maximum acceptable consequence limit as a control instrument N2 - The presentation starts with the first agreement of making a national attempt for the introduction of a pV-limit for hydrogen transport. It explains aspects of the technical development, provides an impression of catastrophic incidents, and explains the difference between risk control and consequence limitation. Then the process of determining consequences and the result from the discussion at the UN-WG are explained. The next part summarises the approach for counting the number of impacted persons as a function of the model of pressure wave, the pressure peak, the limits of injured persons and the population density. Finally, the latest state of the discussion and the subsequent recommendations for a pV-value and the adequate phrases for explanation are introduced. T2 - 29th BAM-DIN-IGV-DVFG-Meeting CY - Online meeting DA - 23.02.2022 KW - Hydrogen KW - Pressure recepacles KW - Consequence limit KW - Risk control KW - Population density KW - Pressure wave PY - 2022 AN - OPUS4-54608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jafari, Abbas A1 - Titscher, Thomas A1 - Chatzi, E. A1 - Unger, Jörg F. T1 - Variational Bayesian inference of damage in concrete material using spatially-dense data N2 - Numerical simulators, such as finite element models, have become increasingly capable of predicting the behaviour of structures and components owing to more sophisticated underlying mathematical models and advanced computing power. A common challenge lies, however, in calibrating these models in terms of their unknown/uncertain parameters. When measurements exist, this can be achieved by comparing the model response against measured data. Besides uncertain model parameters, phenomena like damage can give rise to further uncertainties; in particular, quasi-brittle materials, like concrete, experience damage in a heterogeneous manner due to various imperfections, e.g. in geometry and boundary conditions. This hardens an accurate prediction of the damaged behaviour of real structures that comprise such materials. In this study, which draws from a data-driven approach, we use the force-version of the finite element model updating method (FEMU-F) to incorporate measured displacements into the identification of the damage parameters, in order to cope with heterogeneity. In this method, instead of conducting a forward evaluation of the model and comparing the model response (displacements) against the data, we impose displacements to the model and compare the resulting force residuals with measured reaction forces. To account for uncertainties in the measurement of displacements, we endow this approach with a penalty term, which reflects the discrepancy between measured and imposed displacements, where the latter is assumed as unknown random variables to be identified as well. A Variational Bayesian approach is used as an approximating tool for computing posterior parameters. The underlying damage model considered in this work is a gradient-enhanced damage model. We first establish the identification procedure through two virtual examples, where synthetic data (displacements) are generated over a certain spatially-dense set of points over the domain. The procedure is then validated on an experimental case-study; namely a 3-point bending experiment with displacement measurements resulting from a digital image correlation (DIC) analysis. T2 - MSE 2022 CY - Online meeting DA - 27.09.2022 KW - Heterogeneity KW - Gradient damage KW - Model updating KW - Variational Bayesian KW - Concrete PY - 2022 AN - OPUS4-56625 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tamsen, Erik A1 - Unger, Jörg F. T1 - Towards an automatic optimization framework for performance oriented precast concrete design N2 - Concrete has a long history in the construction industry and is currently one of the most widely used building materials. Especially precast concrete elements are frequently utilized in construction projects for standardized applications, increasing the quality of the composite material, as well as reducing the required building time. Despite the accumulated knowledge, continuous research and development in this field is essential due to the complexity of the composite combined with the ever-growing number of applications and requirements. Especially in view of global climate change, design aspects as CO2 emissions and resource efficiency require new mix designs and optimization strategies. A result of the material’s high complexity and heterogeneity on multiple scales is that utilizing the full potential with changing demands is highly challenging, even for the established industry. We propose a framework based on an ontology, which automatically combines experimental data with numerical simulations. This not only simplifies experimental knowledge transfer, but allows the model calibration and the resulting simulation predictions to be reproducible and interpretable. This research shows a way towards a more performance oriented material design. Within this talk we present our workflow for an automated simulation of a precast element, demonstrating the interaction of the ontology and the finite element simulation. We show the automatic calibration of our early-age concrete model [1, 2], to improve the prediction of the optimal time for the removal of the form work. T2 - The 8th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS) 2022 CY - Oslo, Norway DA - 05.06.2022 KW - Performance oriented concrete design KW - Early-age concrete KW - Precast concrete KW - Ontology KW - Optimization workflow PY - 2022 AN - OPUS4-55302 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Titscher, Thomas A1 - Robens-Radermacher, Annika A1 - Unger, Jörg F. T1 - Model calibration and damage detection for a digital twin N2 - Numerical models are an essential tool in predicting and monitoring the behavior of civil structures. Inferring the model parameters is a challenging tasks as they are often measured indirectly and are affected by uncertainties. Digital twins couple those models with real-world data and can introduce additional, systematic sensor uncertainties related to the sensor calibration, i.e. uncertain offsets and calibration factors. In this work, the challenges of data processing, parameter identification, model selection and damage detection are explored using a lab-scale cable stayed bridge demonstrator. By combining force measurements in the cables with displacement measurements from both laser and stereo-photogrammetry systems, the elastic parameters of a three-dimensional finite element beam model are inferred. Depending on the number of sensors and the number of datasets used, parametrizing the sensor offsets and factors, leads to model with over 100 parameters. With a real-time solution of the problem in mind, a highly efficient analytical variational Bayesian approach is used to solve it within seconds. An analysis of the required assumptions and limitations of the approach, especially w.r.t. to the computed evidence, is provided by a comparison with dynamic nested sampling in a simplified problem. Finally, by inferring the value of additional damage parameters along the bridge, the method is successfully used to detect the location of an artificially introduced weak spot in the demonstrator bridge. T2 - ECCOMAS 2022 CY - Oslo, Norway DA - 05.06.2022 KW - Bayesian identification KW - Digital twin KW - Variational Bayesian KW - Damage detection PY - 2022 AN - OPUS4-55083 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Role of the Authority in the Approval Process of Packaging N2 - In Germany, BAM is the competent authority in the field of dangerous goods transport. The international dangerous goods transportation rules are presented and their adaptation into German law is described. BAM is responsible for dangerous goods packaging testing, manufacturer surveillance, packaging approvals and inspection of IBC and provides “Gefahrgutregeln” (GGR) to define the processes, e.g. of dangerous goods packagings approvals and surveillance.” T2 - Sino-German Workshop on Dangerous Goods Packaging CY - Online meeting DA - 18.11.2022 KW - Gefahrgutverpackungen KW - Zulassung KW - ADR PY - 2022 AN - OPUS4-56754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Birgit A1 - Pirskawetz, Stephan A1 - Tamsen, Eric A1 - Unger, Jörg F. T1 - Betondesign digital - Potenziale für das Bauwesen N2 - Beton ist weltweit einer der wichtigsten Konstruktionswerkstoffe und zeichnet sich durch eine enorme Anpassungsfähigkeit an sich verändernde Anforderungen aus. Damit verbunden ist eine hohe und kontinuierlich zunehmende Komplexität hinsichtlich der Ausgangsstoffe, Rezepturen und des Herstellungsprozesses. Folglich setzt eine Ausschöpfung des technischen und umweltbezogenen Potenzials der Betonbauweise höchste Expertise bei den Einzelakteuren der Bauindustrie voraus. T2 - MatFo2022 „Vom Material zur Innovation: Digital, Neutral, Vital“ CY - Cologne, Germany DA - 14.11.2022 KW - Beton KW - Zement KW - Digitalisierung KW - Ontologien PY - 2022 UR - https://www.werkstofftechnologien.de/veranstaltungen/matfo2022-vom-material-zur-innovation-digital-neutral-vital AN - OPUS4-59140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strobl, Dominic A1 - Robens-Radermacher, Annika A1 - Ghnatios, C. A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Unger, Jörg F. T1 - PGD model with domain mapping of Bead-on-Plate weld simulation for wire arc additive manufacturing N2 - Numerical simulations are essential in predicting the behavior of systems in many engineering fields and industrial sectors. The development of accurate virtual representations of actual physical products or processes allows huge savings in cost and resources. In fact, digital twins would allow reducing the number of real, physical prototypes, tests, and experiments, thus also increasing the sustainability of the production processes and products’ lifetime. Standard numerical methods fail in providing real time simulations, especially for complex processes such as additive manufacturing applications. This work aims to build up a reduced order model for efficient wire arc additive manufacturing simulations by using the proper generalized decomposition (PGD) [1,2] method. Model order reduction is a popular concept to decrease the computational effort, where each evaluation of the reduced forward model is faster than evaluations using classical methods, even for complex models. The simulation of a moving heat source leads to a hardly separable parametric problem, which is solved by a new mapping approach [3]. Using this procedure, it is possible to create a simple separated representation of the forward model. In this contribution, a PGD model is derived for the first part of wire arc additive manufacturing: bead-on-plate weld. An excellent agreement with a standard finite element method is shown. The reduced model is further used in a model calibration set up, speeding up calibrations and ultimately leading to an optimized real-time simulation. T2 - The 8th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS) 2022 CY - Oslo, Norway DA - 05.06.2022 KW - PGD KW - Model calibration KW - Hardly separable problem KW - Additive manufacturing PY - 2022 AN - OPUS4-55111 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. T1 - Combining Data and Simulation Models in real time - A Digital Twin for Bridge monitoring N2 - Im Rahmen des Vortrages wurde das Konzept eines digitalen Zwillings vorgestellt und an verschiedenen Beispielen angefangen von einem Laborversuch über Kleinversuche bis zum Realmaßstab dargestellt. N2 - During the lecture, the concept of a digital twin was presented and illustrated with various examples starting from a laboratory experiment to small-scale and real-scale experiments. T2 - EURAD Second Annual Event (2022) CY - Online meeting DA - 28.03.2022 KW - Digital Twin KW - Bridge Monitoring KW - Simulation Models PY - 2022 UR - https://igdtp.eu/event/eurad-annual-event-2/ AN - OPUS4-54639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Diercks, Philipp A1 - Veroy, K. A1 - Robens-Radermacher, Annika A1 - Unger, Jörg F. T1 - Multiscale modeling of heterogeneous structures based on a localized model order reduction approach N2 - Many of today’s problems in engineering demand reliable and accurate prediction of failure mechanisms of mechanical structures. Herein, it is necessary to take into account the heterogeneous structure on the lower scale, to capture the underlying physical phenomena. However, this poses a great challenge to the numerical solution as the computational cost is significantly increased by resolving the lower scale in the model. Moreover, in applications where scale separation as the basis of classical homogenization schemes does not hold, the influence of the lower scale on the upper scale has to be modelled directly. This work aims to develop an efficient concurrent methodology to model heterogeneous structures combining the variational multiscale method (VMM) [1] and model order reduction techniques (e. g. [2]). First, the influence of the lower scale on the upper scale can be taken into account following the additive split of the displacement field as in the VMM. Here, also a decomposition of the global domain into subdomains, each containing a fine grid discretization of the lower scale, is introduced. Second, reduced approximation spaces for the upper and lower scale solution are constructed by exploring possible solutions for each subdomain based on a representative unit cell. The local reduced spaces are designed such that local contributions of each subdomain can be coupled in a conforming way. Thus, the resulting global system is sparse and reduced in size compared to the direct numerical simulation, leading to a faster solution of the problem. The authors gratefully acknowledge financial support by the German Research Foundation (DFG), project number 394350870, and by the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (ERC Grant agreement No. 818473). T2 - The 8th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS) 2022 CY - Oslo, Norway DA - 05.06.2022 KW - Multiscale methods KW - Variational multiscale method KW - Domain decomposition KW - Model order reduction PY - 2022 AN - OPUS4-55117 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -