TY - JOUR A1 - Strommer, Bettina A1 - Battig, Alexander A1 - Frasca, Daniele A1 - Schulze, Dietmar A1 - Huth, Christian A1 - Böhning, Martin A1 - Schartel, Bernhard T1 - Multifunctional Property Improvements by Combining Graphene and Conventional Fillers in Chlorosulfonated Polyethylene Rubber Composites N2 - The incorporation of nanoparticles like multilayer graphene (MLG) into elastomeric composites boosts their technical performance, such as their mechanical behavior and electrical conductivity. Common filler types (carbon black (CB) and aluminum trihydroxide (ATH)) generally fulfill single, specific purposes and are often used in high loadings. CB typically reinforces rubber mechanically, while ATH increases flame retardancy. Small amounts of MLG reduce these high filler contents and maintain the multifunctional characteristics of rubber composites. In chlorosulfonated polyethylene (CSM) + ATH, an intrinsically flame-retardant rubber was designed to achieve the highest standards such as maximum average of heat emission (MARHE) <90 kW m−2, 3 phrMLG was substituted for 15 phr CB and/or 3 phr ATH via an industrially applicable processing approach. Replacing either CB or ATH resulted in a property profile that was multifunctionally improved in terms of features such as mechanical performance, reduced sorption, and flame retardance. MLG nanocomposites are reported to show promise as an industrially utilizable route to obtain multifunctional high-performance rubbers. KW - Nanocomposites KW - Rubber KW - Multilayer graphene KW - Flame retardancy KW - Synergy KW - Nanoparticles KW - Elastomers PY - 2022 DO - https://doi.org/10.1021/acsapm.1c01469 SN - 2637-6105 VL - 4 IS - 2 SP - 1021 EP - 1034 PB - ACS Publ. CY - Washington, DC AN - OPUS4-54330 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Diercks, Philipp T1 - Multiscale modeling of heterogeneous structures based on a localized model order reduction approach N2 - Many of today’s problems in engineering demand reliable and accurate prediction of failure mechanisms of mechanical structures. Herein, it is necessary to take into account the heterogeneous structure on the lower scale, to capture the underlying physical phenomena. However, this poses a great challenge to the numerical solution as the computational cost is significantly increased by resolving the lower scale in the model. Moreover, in applications where scale separation as the basis of classical homogenization schemes does not hold, the influence of the lower scale on the upper scale has to be modelled directly. This work aims to develop an efficient concurrent methodology to model heterogeneous structures combining the variational multiscale method (VMM) [1] and model order reduction techniques (e. g. [2]). First, the influence of the lower scale on the upper scale can be taken into account following the additive split of the displacement field as in the VMM. Here, also a decomposition of the global domain into subdomains, each containing a fine grid discretization of the lower scale, is introduced. Second, reduced approximation spaces for the upper and lower scale solution are constructed by exploring possible solutions for each subdomain based on a representative unit cell. The local reduced spaces are designed such that local contributions of each subdomain can be coupled in a conforming way. Thus, the resulting global system is sparse and reduced in size compared to the direct numerical simulation, leading to a faster solution of the problem. The authors gratefully acknowledge financial support by the German Research Foundation (DFG), project number 394350870, and by the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (ERC Grant agreement No. 818473). T2 - The 8th European Congress on Computational Methods in Applied Sciences and Engineering (ECCOMAS) 2022 CY - Oslo, Norway DA - 05.06.2022 KW - Multiscale methods KW - Variational multiscale method KW - Domain decomposition KW - Model order reduction PY - 2022 AN - OPUS4-55117 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Diercks, Philipp T1 - Multiscale modeling of heterogeneous structures based on a localized model order reduction approach N2 - Many of today’s problems in engineering demand reliable and accurate prediction of failure mechanisms of mechanical structures. Thus, it is necessary to take into account the heterogeneous structure on the smaller scale, to capture the underlying physical phenomena. However, this poses a great challenge to the numerical solution since the computational cost is significantly increased by resolving the smaller scale in the model. Moreover, in applications where scale separation as the basis of classical homogenization schemes does not hold, the influence of the smaller scale on the larger scale has to be modelled directly. This work aims to develop an efficient concurrent methodology to model heterogeneous structures combining the variational multiscale method (VMM) and model order reduction techniques. First, the influence of the smaller scale on the larger scale can be taken into account following the additive split of the displacement field as in the VMM. Here, also a decomposition of the global domain into subdomains, each containing a fine grid discretization of the smaller scale, is introduced. Second, local reduced approximation spaces for the smaller scale solution are constructed by exploring possible solutions for each subdomain based on the concept of oversampling and the solution of the associated transfer operator problem. Herein, we propose to choose the training data based on the solution of a reduced global problem to incorporate the actual physical behaviour of the structure of interest and to extend it by random samples to ensure sufficient approximation capabilities in general. The local reduced spaces are designed such that local contributions of each subdomain can be coupled in a conforming way. Thus, the resulting global system is sparse and reduced in size compared to the direct numerical simulation, leading to a faster solution of the problem. The authors gratefully acknowledge financial support by the German Research Foundation (DFG), project number 394350870, and by the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (ERC Grant agreement No. 818473). T2 - Model Reduction and Surrogate Modeling (MORE) CY - Berlin, Germany DA - 19.09.2022 KW - Domin decomposition KW - Model oder reduction KW - Multiscale methodes KW - Variational multiscale method PY - 2022 AN - OPUS4-57332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Guangliang, Y. A1 - Mahon, D. A1 - Gardner, S. T1 - Muon tomography applied to assessment of concrete structures: First experiments and simulations. N2 - Non-destructive techniques for reinforced or prestressed concrete inspection such as ultrasound or radar have found regular, successful practical application but sometimes suffer from limited resolution and accuracy, imaging artefacts or restrictions in detecting certain features. Until the 1980s X-ray transmission was used in case of special demands and showed a much better resolution than other NDT techniques. However, due to safety concerns and cost issues, this method is almost never used anymore. Muon tomography has received much attention recently. Novel detectors for cosmic muons and tomographic imaging algorithms have opened new fields of application. As a first step towards practical application in civil engineering and as a proof of concept we used an existing system to image the interior of a reference reinforced 600 kg concrete block. Even with a yet not optimized setup for this kind of investigation, the muon imaging results are at least of similar quality compared to ultrasonic and radar imaging, potentially even better. In a second step, we have performed simulations to assess the potential for a set of important testing problems such as grouting defects in tendon ducts. The next steps include the development of mobile detectors and optimizing acquisition and imaging parameters. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Muon tomography KW - Concrete KW - Inspection KW - Simulation PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-563224 UR - https://www.ndt.net/article/ndtce2022/paper/60943_manuscript.pdf SP - 1 EP - 8 PB - NDT.net AN - OPUS4-56322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Muon tomography applied to assessment of concrete structures: First experiments and simulations. N2 - Non-destructive techniques for reinforced or prestressed concrete inspection such as ultrasound or radar have found regular, successful practical application but sometimes suffer from limited resolution and accuracy, imaging artefacts or restrictions in detecting certain features. Until the 1980s X-ray transmission was used in case of special demands and showed a much better resolution than other NDT techniques. However, due to safety concerns and cost issues, this method is almost never used anymore. Muon tomography has received much attention recently. Novel detectors for cosmic muons and tomographic imaging algorithms have opened new fields of application. As a first step towards practical application in civil engineering and as a proof of concept we used an existing system to image the interior of a reference reinforced 600 kg concrete block. Even with a yet not optimized setup for this kind of investigation, the muon imaging results are at least of similar quality compared to ultrasonic and radar imaging, potentially even better. In a second step, we have performed simulations to assess the potential for a set of important testing problems such as grouting defects in tendon ducts. The next steps include the development of mobile detectors and optimizing acquisition and imaging parameters. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Muon tomography KW - Concrete KW - Inspection KW - Simulation PY - 2022 AN - OPUS4-56323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Mythos oder Wahrheit - die kalte Pyrotechnik N2 - Beschreibung akktueller Gefährdungen beim Missbrauch von Pyrotechnik in Stadien, insbesondere Fackeln. Produktentwicklung "kalte Pyrotechnik" wurde bewertet im Hinblick auf Temperatur und Aerosolemissionen. T2 - 22. Internationales Symposium des Bundeskriminalamtes für Sprengstoffermittelnde und Entschärfende unkonventioneller Spreng- und Brandvorrichtungen CY - Magdeburg, Germany DA - 28.11.2022 KW - Pyrotechnik KW - Fackeln KW - Aerosole KW - Fussballstadien PY - 2022 AN - OPUS4-56448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Mögliche Fehlerquellen in der Praxis N2 - Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. Bei der Durchführung dieser Messung gibt es jedoch messtechnikspezifische Fehlerquellen und äußere Einflüsse aus dem zu untersuchenden Bauwerk die eine Interpretation der Messergebnisse signifikant beeinflussen können. T2 - Sachkundelehrgang zur Durchführung von Potentialfeldmessungen 2022 CY - Baruth/Mark, Germany DA - 16.05.2022 KW - Korrosion KW - Potentialfeldmessung PY - 2022 AN - OPUS4-54872 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Neue Erkenntnisse zu wasserstoffinduzierten Spannungsrissen infolge korrosiver Belastung hochempfindlicher Spannstähle in Spannblockverfahren nach TGL 173-33 N2 - Brückenbauwerke, die im Spannblockverfahren hergestellt wurden, können bauartbedingt wasserstoffinduzierte Spannungsrisse über den gesamten Querschnitt eines Spannkanals aufweisen. Das Risswachstum kann infolge dynamischer Beanspruchung über die Nutzungsdauer fortschreiten und zu Spanndrahtbrüchen führen. T2 - 5. Brückenkoloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Korrosion KW - Spannungsrisskorrosion KW - Brücke KW - Wasserstoff PY - 2022 AN - OPUS4-55663 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Neue Erkenntnisse zu wasserstoffinduzierten Spannungsrissen infolge korrosiver Belastung hochempfindlicher Spannstähle in Spannblockverfahren nach TGL 173-33 N2 - Brückenbauwerke, die im Spannblockverfahren hergestellt wurden, können bauartbedingt wasserstoffinduzierte Spannungsrisse über den gesamten Querschnitt eines Spannkanals aufweisen. Das Risswachstum kann infolge dynamischer Beanspruchung über die Nutzungsdauer fortschreiten und zu Spanndrahtbrüchen führen. T2 - 5. Brückenkolloquium CY - Ostfildern, Germany DA - 06.09.2022 KW - Korrosion KW - Spannungsrisskorrosion KW - Spannstahl PY - 2022 SP - 567 EP - 572 PB - Expert -TAE CY - Esslingen AN - OPUS4-55662 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin A1 - Hothan, Sascha T1 - Neue Prüfnorm für reaktive Brandschutzsysteme auf Stahlzuggliedern N2 - Der Vortrag stellt den Entwurf der neuentwickelten Prüfnorm vor. T2 - Workshop 2022 - Feuerwiderstand von Stahlzuggliedern mit reaktiver Brandschutzbeschichtung CY - Berlin, Germany DA - 06.09.2022 KW - Feuerwiderstand KW - Brandschutz KW - Stahlzugglieder KW - Reaktives Brandschutzsystem KW - Prüfnorm PY - 2022 AN - OPUS4-55701 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -