TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Wie weiter in Ressourcenfragen? N2 - Entwicklung der gesetzlichen Anforderungen an die Ressourceneffizienz und aktuelle Aktivitäten der Europäischen Kommission. T2 - Praxisworkshop Marktüberwachung CY - Gernsbach, Germany DA - 16.05.2018 KW - Ressourcen KW - Energiepolitik KW - Ökodesign PY - 2018 AN - OPUS4-44950 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Ökodesign: Mehr als nur „Licht aus!“ - Die Europäische Kommission und die Ressourceneffizienz N2 - - Bisherige und zukünftige gesetzliche Anforderungen an die Ressourcen- und Materialeffizienz - Entwicklungsstand der Normen zur Umsetzung des Circular Economy Action Plan (M/543) - Wann kommt das „Winterpaket“ und was beinhaltet es? T2 - ExFo 2018 – Global Environmental Compliance CY - Stuttgart, Germany DA - 13.11.2018 KW - Circular economy KW - Durability KW - Reparability KW - Recycability KW - Ecodesign PY - 2018 AN - OPUS4-46588 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Gut Ding braucht Weile - Ressourceneffizienz im Ökodesign und das „Winterpaket“ N2 - Die Kreislaufwirtschaftsinitiative der Europäischen Kommission fordert klar grundlegende Aspekte der Kreislaufwirtschaft in bereits bestehende Rechtsrahmen einzubetten. Anforderungen zur gesetzlich vorgeschriebenen Lebensdauer, Reparierbarkeit und Recyclingfähigkeit von Produkten sollen zukünftig auf europäischer Ebene ins Leben gerufen werden. Ein geeignetes Spielfeld ist die Ökodesign-Richtlinie. Momentan regelt sie primär die Energieeffizienz von energieverbrauchsrelevanten Produkten, doch der Fokus wird aktuell um Anforderungen an den nachhaltigen Einsatz von Ressourcen erweitert. Bei den gegenwärtigen Aktivitäten im Ökodesign steht der Normungsauftrag M/543 im Zentrum. Es wurde 2015 von der Europäischen Kommission an CEN/CENELEC vergeben und später stieß auch ETSI dazu. Bislang sind acht generische EN-Normen und zwei Fachberichte (Technical Report (TR)) geplant. Sie sollen grundlegende Aspekte der Nachhaltigkeit von energieverbrauchsrelevanten Produkten, die von der Ökodesign-Richtlinie betroffen sind, abdecken. Trotz der zu erwartenden hohen Reichweite dieses Vorhabens scheinen die Inhalte und der eigentliche Zweck der zu erarbeitenden Normen vielen Marktakteuren noch nicht vollständig bekannt zu sein. Daher hat ein nationaler Zentralverband eingeladen zu berichten. In dem Vortrag werden Antworten auf folgende Fragen gegeben: Warum im Ökodesign? Was ist geplant? Was ist betroffen? Worum geht es in den Normen? T2 - AK-Sitzung CY - ZVEI, Frankfurt a. Main, Germany DA - 19.09.2018 KW - Normung KW - Ressourceneffizienz KW - Ökodesign KW - Kreislaufwirtschaft PY - 2018 AN - OPUS4-45992 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Elektro"älter"geräte N2 - Inhalte: (i) Gründe für Ressourceneffizienzanforderungen im Ökodesign. (ii) Bisherige und zukünftige gesetzliche Anforderungen an die Ressourcen-/Materialeffizienz (iii) Entwicklungsstand der Normen zur Umsetzung des Circular Economy Action Plan – M/543 T2 - VDI Wissensforum CY - Dusseldorf, Germany DA - 05.12.2018 KW - Kreislaufwirtschaft KW - Ökodesign KW - Ressourceneffizienz KW - Normung KW - Europäische Kommission PY - 2018 AN - OPUS4-46921 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Nicht nur „unter Strom“ - Ressourceneffizienz im Ökodesign N2 - Zusammenfassung des aktuellen Standes der Entwicklungen im Ökodesign mit dem Schwerpunkt auf zukünftige Geltungsbereiche. T2 - Abteilungskolloquium Abetilung S CY - BAM AH, Berlin, Germany DA - 28.06.2018 KW - Ressourceneffizienz KW - Kreislaufwirtschaft KW - Ökdoesign KW - Rechtssetzung PY - 2018 AN - OPUS4-46156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ringleben-Fricke, Thomas A1 - Schlegel, Moritz-Caspar T1 - Einführung in die Nutzung der Internetplattform Erfahrungsaustausch N2 - Einführungsveranstaltung zur Nutzung einer Internetplattform für die Marktüberwachung (erstellt von einer AG des BLA EVPG/EnVKG, Vorsitz HH und BAM) T2 - Praxisworkshop Marktüberwachung CY - Gernsbach, Germany DA - 16.05.2018 KW - Internetplattform KW - Marktüberwachung KW - Ökodesign KW - Energieverbrauchskennzeichnung PY - 2018 AN - OPUS4-44951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten A1 - Zottl, A. T1 - Dynamische Energieeffizienzprüfung von Wärmepumpen N2 - Die bisher üblichen Verfahren zur Bewertung der Effizienz einer Wärmepumpe durch Labormessungen berücksichtigen kaum transiente Zustände. Können dynamische Bewertungsverfahren im Labor ein realistischeres Verhalten im Feld wiederspiegeln und damit zu sinnvolleren Entscheidungen führen? T2 - Chillventa 2018 CY - Nuremberg, Germany DA - 15.10.2018 KW - Wärmepumpen KW - Energieeffizienz KW - Dynamische Prüfung KW - Methodenentwicklung KW - Energielabel PY - 2018 AN - OPUS4-46343 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten A1 - Schlegel, Moritz-Caspar A1 - Akkerman, Floris A1 - Simo, Anne T1 - How cool? - Energy label for air conditioners and possibilities for circumvention N2 - In this study, the test method EN 14825 for testing air conditioners is validated by verifying the sensitivity of the seasonal energy efficiency ratio SEER (declared on the energy efficiency label) in relation to the nominal cooling capacity Pdesign. Therefore, the two major parts of the test method, the measurement part and the calculation part, were investigated. Measurements were conducted on several single-split units. The calculation part was subjected to a sensitivity analysis in order to identify the properties of an air conditioner which have a strong influence on the SEER. The analysis revealed that the measurement procedure delivers reproducible results. However, the energy consumption in special operating states, the duration in active-mode and seasonal performance values in active mode (SEERon) significantly affect the sensitivity of the SEER. Especially assumption of short operating times for a cooling active mode leads to large changes in the SEER with varying Pdesign. In addition, the range of power of Pdesign turned out to have an increasing impact on the SEER with decreasing Pdesign. For Pdesign values ≤10 kW, which is the most popular type of ACs in the EU, the sensitivity of the SEER increases tremendously. Especially the determination of the SEER for devices with short operating times in cooling active-mode (350 h) and low values for Pdesign (≤10 kW) cannot be reproduced anymore. In consequence, manufacturer could use the sensitivity of the SEER on Pdesign to artificially “increase” the energy efficiency of their air conditioner for the Energy label about 10 %. T2 - World Sustainable Energy Days CY - Wels, Austria DA - 28.02.2018 KW - Air Conditioner KW - Energy Efficiency KW - Circumvention KW - Energy Label PY - 2018 AN - OPUS4-47480 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mirtsch, Mona ED - Jakobs, K. ED - O'Connor, R.V. T1 - The Role of Conformity Assessment in the Digital Transformation: Focusing on Cybersecurity N2 - Digital transformation and especially the dramatic rise of products and services connected to the Internet of Things raise the questions on how to deal with the increasing risks related to Privacy and Cybersecurity. Presumably, these risks seem to be insufficiently reflected in the European Union’s current regulative system – by being neither part of the traditional definition of a safe product nor part of product-specific vertical or horizontal directives. Certification based on standards as underlying requirements has been identified by policymakers as an instrument to address this issue. The latest European draft regulation aims at increasing security and trust in ICT products and services, and reducing current European market fragmentation with a new Cybersecurity Certification Framework. Based on the results of a qualitative analysis of stakeholder statements on the current proposal on the Cybersecurity Act, this paper discusses elements of the proposed Cybersecurity Certification Framework. As a theoretical background, this paper provides definitions of the terms Safety, IT-security, and Cybersecurity, presents selected Cybersecurity-related standards and provides an outlook on future challenges to Conformity Assessment in the digital transformation. T2 - 23rd EURAS Annual Standardisation Conference "Standards for a Smarter Future" CY - Dublin, Irland DA - 13.06.2018 KW - Conformity Assessment KW - Cybersecurity KW - Certification KW - IT-Security PY - 2018 SN - 978-3-95886-229-6 VL - 2018 SP - 183 EP - 202 PB - Verlagshaus Mainz GmbH Aachen CY - Aachen AN - OPUS4-45686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mirtsch, Mona T1 - The Role of Conformity Assessment in the Digital Transformation: Focusing on Cybersecurity N2 - Digital transformation and especially the dramatic rise of products and services connected to the Internet of Things raise the questions on how to deal with the increasing risks related to Privacy and Cybersecurity. Presumably, these risks seem to be insufficiently reflected in the European Union’s current regulative system – by being neither part of the traditional definition of a safe product nor part of product-specific vertical or horizontal directives. Certification based on standards as underlying requirements has been identified by policymakers as an instrument to address this issue. The latest European draft regulation aims at increasing security and trust in ICT products and services, and reducing current European market fragmentation with a new Cybersecurity Certification Framework. Based on the results of a qualitative analysis of stakeholder statements on the current proposal on the Cybersecurity Act, this paper discusses elements of the proposed Cybersecurity Certification Framework. As a theoretical background, this paper provides definitions of the terms Safety, IT-security, and Cybersecurity, presents selected Cybersecurity-related standards and provides an outlook on future challenges to Conformity Assessment in the digital transformation. T2 - 23rd EURAS Annual Standardisation Conference "Standards for a Smarter Future" CY - Dublin, Irland DA - 13.06.2018 KW - Cybersecurity KW - Certification KW - Conformity Assessment KW - IT-Security PY - 2018 AN - OPUS4-45687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -