TY - CONF A1 - Chaudhuri, Somsubhro T1 - WTB-IRT: Modelling and Measurement of Thermal Contrast in wind turbine rotor blades (WTBs) N2 - To understand the results that can be obtained with thermography of operational wind turbine blades, a climate chamber based experiment was performed. The results of these experiments were additionally modelled using COMSOL Multiphysics. The results have been presented at the conference. T2 - Advanced Infrared Technology and Applications (AITA) 2025 CY - Kobe, Japan DA - 15.09.2025 KW - Thermography KW - Thermografie KW - Wind turbine rotor blades KW - Windenergie Anlage Rotorblätter KW - FEA PY - 2025 AN - OPUS4-64222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro A1 - Krankenhagen, Rainer A1 - Lapšanská, Ivana A1 - Stamm, Michael T1 - WTB-IRT: Modelling and Measurement of Thermal Contrast in Wind Turbine Rotor Blades (WTBs) N2 - The rapid growth of wind energy infrastructure over the past two to three decades has led to an urgent need for advanced non-destructive testing (NDT) methods—both for newly installed wind turbine blades (WTBs) and for ageing components nearing the end of their service life. Among emerging techniques, passive infrared thermography (IRT) offers a promising solution by enabling contactless, time-efficient inspection based on naturally occurring thermal variations. The effectiveness of passive IRT depends on the presence of sufficient thermal contrast to distinguish surface features, subsurface structures, and defects. To better understand the possibility of obtaining such contrast in composite structures such as WTBs, a controlled study was carried out on a blade section exposed to programmed temperature transients in a climate chamber. Infrared measurements were recorded, and the thermal behaviour of the specimen was simulated using finite element models (FEM) in COMSOL Multiphysics 6.3. Although direct validation is limited by measurement uncertainties and transient effects, the comparison provides insight into the capabilities and limitations of FEM in replicating real-world thermal behaviour. This paper focuses specifically on the challenges related to the modelling approach. T2 - 18th International Workshop on Advanced Infrared Technology and Applications (AITA 2025) CY - Kobe, Japan DA - 15.09.2025 KW - Thermography KW - Wind energy KW - Wind turbine rotor blades KW - Windenergie Anlage Rotorblätter KW - FEA PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-642308 DO - https://doi.org/10.3390/proceedings2025129015 VL - 129 IS - 1 SP - 1 EP - 5 PB - MDPI CY - Basel AN - OPUS4-64230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael A1 - Krankenhagen, Rainer T1 - Weather-dependent passive thermography of unheated wind turbine blades N2 - Up to now, the inspection of wind turbines with industrial climbers has been considered ”state of the art”. However, ever-larger wind turbines and advancing digitization make modern and automated inspection methods indispensable. Passive thermography can serve as such a digital and atomized method while it is well known for its applications in the inspection of buildings or electrical circuits. However, its application relies on thermal gradients in the inspected object such that a temperature contrast exists between damaged and sound areas. This also holds for unheated structures like rotor blades of wind turbines which show no intrinsic temperature gradient and can hardly be heated. Under certain weather conditions with sufficient solar loading and diurnal temperature variations, passive thermography is suitable for the in-service inspection of rotor blades. However, for a reliable use of passive thermography on ”thermal passive” components, the incorporation of these environmental conditions in the planning and evaluation of thermal inspections is crucial. Additionally, the complex inner structure of wind turbine blades in comparison to other objects and buildings require a specific method referencing the individual rotor blades to each other. This allows the distinction between the thermal response of design-specific structural features and damages or irregularities between the three blades. We show thermal signatures of damage in rotor blades and contrast them with structural characteristics by comparing the three blades. In addition to measurements in industrial environments, laboratory measurements are shown and compared to simulations. The long-term goal is to simulate the influence of different weather parameters and thus gain a better understanding of measurements in the field. The results shown here can be seen as one step towards industrial application. T2 - SPIE Defense + Commercial Sensing CY - Orlando, Florida, USA DA - 03.04.2022 KW - Passive thermography KW - Wind energy KW - FEM simulations PY - 2022 DO - https://doi.org/10.1117/12.2618740 VL - 12109 SP - 1 EP - 8 PB - Society of Photo-Optical Instrumentation Engineers (SPIE) AN - OPUS4-54943 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Weather-dependent passive thermography of unheated wind turbine blades N2 - Up to now, the inspection of wind turbines with industrial climbers has been considered ”state of the art”. However, ever-larger wind turbines and advancing digitization make modern and automated inspection methods indispensable. Passive thermography can serve as such a digital and atomized method while it is well known for its applications in the inspection of buildings or electrical circuits. However, its application relies on thermal gradients in the inspected object such that a temperature contrast exists between damaged and sound areas. This also holds for unheated structures like rotor blades of wind turbines which show no intrinsic temperature gradient and can hardly be heated. Under certain weather conditions with sufficient solar loading and diurnal temperature variations, passive thermography is suitable for the in-service inspection of rotor blades. However, for a reliable use of passive thermography on ”thermal passive” components, the incorporation of these environmental conditions in the planning and evaluation of thermal inspections is crucial. Additionally, the complex inner structure of wind turbine blades in comparison to other objects and buildings require a specific method referencing the individual rotor blades to each other. This allows the distinction between the thermal response of design-specific structural features and damages or irregularities between the three blades. We show thermal signatures of damage in rotor blades and contrast them with structural characteristics by comparing the three blades. In addition to measurements in industrial environments, laboratory measurements are shown and compared to simulations. The long-term goal is to simulate the influence of different weather parameters and thus gain a better understanding of measurements in the field. The results shown here can be seen as one step towards industrial application. T2 - Defense + Commercial Sensing 2022 CY - Orlando, Florida, USA DA - 3.4.2022 KW - Passive thermography KW - Wind energy KW - FEM simulations PY - 2022 UR - https://spie.org/defense-commercial-sensing/presentation/Weather-dependent-passive-thermography-of-unheated-wind-turbine-blades/12109-19?SSO=1 AN - OPUS4-54944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chaudhuri, Somsubhro A1 - Stamm, Michael A1 - Krankenhagen, Rainer T1 - Weather-dependent passive thermography and thermal simulation of in-service wind turbine blades N2 - . To cope with the increase in the manufacturing and operation of wind turbines, wind farm operators need inspection tools that are able to provide reliable information while keeping the downtime low. Current inspection techniques require to stop the wind turbine. This work presents the current progress in the project EvalTherm, in which passive thermography is evaluated as a possible non-destructive inspection tool for operational wind turbine blades (WTBs). A methodology to obtain thermal images of rotating WTBs has been established in this project. However, the quality of the results is heavily dependent on various aspects such as weather conditions, information on the inspected WTB, damage history, etc. In this work, a section of a used WTB is simulated using finite-element modelling (FEM) as well as experimentally tested for evaluating the accuracy of the model. Such a model will provide insight into the potential thermal response of a certain structure (with specific material properties) in given weather (boundary) conditions. The model is able to provide satisfactory predictions of the thermal response of the structure, as well as indicate what thermal contrast(s) result from artificial defects introduced in the structure. T2 - WindEurope Annual Event 2023 CY - Copenhagen, Denmark DA - 25.04.2023 KW - FEM KW - Thermografie KW - Wind turbine rotor blades KW - Windenergie Anlage Rotorblätter PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582777 DO - https://doi.org/10.1088/1742-6596/2507/1/012025 VL - 2507 SP - 1 EP - 12 PB - IOP Publishing Ltd. AN - OPUS4-58277 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro T1 - Weather-dependent passive thermography and thermal simulation of in-service wind turbine blades N2 - The thermographic methods NDT division of BAM is aiming to develop a wind turbine blade (WTB) inspection tool using infrared thermographic scanning of operational wind turbines in the project EvalTherm. T2 - WindEurope Annual Event 2023 CY - Copenhagen, Denmark DA - 25.04.2023 KW - FEM KW - Thermografie KW - Wind turbine rotor blades KW - Windenergie anlage rotorblätte PY - 2023 AN - OPUS4-58275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheuschner, Nils A1 - Altenburg, Simon A1 - Pignatelli, Giuseppe A1 - Maierhofer, Christiane A1 - Straße, Anne A1 - Gornushkin, Igor B. A1 - Gumenyuk, Andrey T1 - Vergleich der Messungen der Schmelzbadtemperatur bei der Additiven Fertigung von Metallen mittels IR-Spektroskopie und Thermografie T1 - Comparison of measurements of the melt pool temperature during the additive production of metals by means of IR spectroscopy and thermography N2 - Im Rahmen des Themenfeldprojektes „Process Monitoring of AM“ (ProMoAM) evaluiert die Bundesanstalt für Materialforschung und -Prüfung (BAM) gegenwärtig die Anwendbarkeit verschiedenster ZfP-Verfahren zur in-situ Prozessüberwachung in der additiven Fertigung (AM) von Metallen in Hinblick auf die Qualitätssicherung. Einige der wichtigsten Messgrößen sind hierbei die Temperatur des Schmelzbades und die Abkühlrate, welche starken Einfluss auf das Gefüge und die Eigenspannung haben. Aufgrund der Zugänglichkeit zum Werkstück während des Bauprozesses bieten sich optische Verfahren zu Temperaturbestimmung an. Hierbei stellen jedoch u. a. die hohe Bandbreite der zu messenden Temperaturen, die Bestimmung der Emissivität und ihre Änderung bei Phasenübergängen der verwendeten Legierung große experimentelle Herausforderungen dar. Eine weitere Herausforderung stellt für die IR-Spektroskopie die Absorption durch das Schutzgas und weitere optische Elemente dar. Um diese auch in einem industriellen Umfeld kompensieren zu können, wurde eine Methode entwickelt, die das gemessene Spektrum bei der Verfestigung des Werkstoffes als Referenz nutzt. In diesem Beitrag wird die Anwendung dieser Methode für die IR-Spektrometrie als auch Thermografische Messungen beim Laser-Pulver-Auftragschweißen von 316L gezeigt, wobei beide Methoden weiterhin in Hinblick auf ihre individuellen Vor- und Nachteile miteinander verglichen werden. N2 - Within the topic area project “Process Monitoring of AM” (ProMoAM) the Federal Institute for Materials Research and Testing is currently evaluating the applicability of various NDT methods for in-situ process Monitoring in the additive manufacturing (AM) of metals with regard to quality assurance. Two of the most important variables to measure are the temperature of the molten pool and the cooling rate, which have a strong influence on the microstructure and the residual stress. Due to the accessibility of the workpiece during the construction process, optical methods for temperature determination are suitable. However, the wide range of temperatures to be measured, the determination of emissivity and its change during phase transitions of the alloy pose great experimental challenges. Another challenge for IR spectroscopy is the absorption by the inert gas and other optical elements. In order to be able to compensate for this in an industrial environment, a method was developed which uses the measured spectrum as a reference when the material is solidified. This paper shows the application of this method for IR spectrometry as well as thermographic measurements during laser powder cladding of 316L. Furthermore both methods are compared with respect to their individual Advantages and disadvantages. KW - Laser-Pulver-Auftragschweißen KW - Thermografie KW - Direct Energy Deposition KW - IR-Spektroskopie KW - Additive Fertigung KW - Laser metal deposition KW - Thermography KW - IR-spectroscopy KW - Additive manufacturing PY - 2021 DO - https://doi.org/10.1515/teme-2021-0056 VL - 88 IS - 10 SP - 626 EP - 632 PB - De Gruyter CY - Oldenburg AN - OPUS4-52987 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Lecompagnon, Julien A1 - Hassenstein, Christian A1 - Thiel, Erik A1 - Pech May, Nelson Wilbur T1 - Using spatial and temporal shaping of laser-induced diffuse thermal wave fields in thermography N2 - The diffuse nature of thermal waves is a fun-damental limitation in thermographic nonde-structive testing. In our studies we investigated different approaches by shaping the thermal wave fields which result from heating. We have used high-power laser sources to heat metallic samples. Using these spatial and temporal shaping techniques leads to a higher detection sensitivity in our measurements with the infra-red camera. In this contribution we show our implementation of shaping laser-induced diffuse thermal wave fields and the effect on the defect reconstruction quality. T2 - SMSI 2020 Conference CY - Online meeting DA - 22.06.2020 KW - Thermal wave KW - Diffusion KW - High-power laser KW - Thermography KW - Spatiotemporal shaping PY - 2020 DO - https://doi.org/10.5162/SMSI2020/C5.1 SP - 179 EP - 180 AN - OPUS4-50897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon T1 - Unraveling thermal radiation by multispectral thermography: Real temperatures in LMD N2 - Additive manufacturing of metals offers the opportunity to build parts with a high degree of complexity without additional costs, opening a new space for design optimization. However, the processes are highly complex and due to the rapid thermal cycles involved, high internal stresses and peculiar microstructures occur, which influence the parts mechanical properties. To systematically examine the formation of internal stresses and the microstructure, in-process spatially resolved measurements of the part temperature are needed. If the emissivity of the inspected part is known, its thermodynamic temperature can be reconstructed by a suited radiometric model. However, in additive manufacturing of metals, the emissivity of the part surface is strongly inhomogeneous and rapidly changing due to variations of, e.g., the degree of oxidation, the material state and temperature. Thus, here, the applicability of thermography in the determination of thermodynamic temperatures is limited. However, measuring the process thermal radiation at different wavelengths simultaneously enables one to separate temperature and emissivity spatially resolved to obtain further insight into the process. Here, we present results of an initial study using multispectral thermography to obtain real temperatures and emissivities in the powderfree LMD process. T2 - 2nd Workshop on In-situ Monitoring and Microstructure Development in Additive Manufactured Alloys CY - Online meeting DA - 19.04.2021 KW - Additive Manufacturing KW - Process monitoring KW - Multispectral thermography KW - Laser metal deposition KW - TES KW - LMD KW - Temperature emissivity separation PY - 2021 AN - OPUS4-52514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Walter, Keven A1 - Hoch, Dominik P. A1 - Hertweck, Leon A1 - Balasubramanian, Kannan A1 - Geisler, Jonas A1 - Röllig, Mathias A1 - Neubert, Tilmann J. A1 - Börner, Hans G. T1 - Unlocking the Essence of Lignin: High‐Performance Adhesives That Bond via Thiol‐Catechol Connectivities and Debond on Electrochemical Command N2 - AbstractThe next generation of adhesives requires effective debonding capabilities that can be triggered on demand to enable advanced circular repair and recycling strategies. A new class of lignin‐inspired, two‐component (2K) structural adhesives offers bonding strengths of up to 20 MPa and clean, on‐command electrochemical debonding within 5–30 min. The debonding is induced by a distinct electrochemical oxidation of thiol‐catechol connectivities (TCCs) within the entire adhesive network, enforcing rapid and clean adhesive failure on the cathodic substrate side. The TCC‐functionalities are formed during curing by a thiol‐quinone Michael‐type polyaddition, reacting polyester‐based trithiols with tris‐quinones as lignin‐inspired minimal building blocks. The structural adhesive can be fine‐tuned by adjusting the formulation. The addition of carbon black and ionic liquids facilitates the desired electrochemical transformation of TCC‐catechols to TCC‐quinones. Applying only 9 V for 5–30 min, leads to clean debonding with 72–86% loss of shear strength. A comprehensive study of curing, bonding, and debonding behavior by rheological, spectroscopic, and electrochemical investigations reveals the debonding mechanism by correlating catechol oxidation to adhesive performance. The electrochemical debonding capability of TCC‐structural adhesives is demonstrated in a functional prototype, where on‐command detachment of a cover glass from a display device is achieved within 6.5 min. KW - Lignin-inspired KW - Electrochemical-Debonding KW - Thiol-Catechol-Connectivity (TCC) KW - Michael-Type Polyaddition KW - On-Demand Adhesive Failure PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639674 DO - https://doi.org/10.1002/adma.202510463 SN - 0935-9648 SP - 1 EP - 10 PB - Wiley VHC-Verlag CY - 69451 Weinheim AN - OPUS4-63967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -