TY - CONF A1 - Chaudhuri, Somsubhro T1 - WTB-IRT: Modelling and Measurement of Thermal Contrast in wind turbine rotor blades (WTBs) N2 - To understand the results that can be obtained with thermography of operational wind turbine blades, a climate chamber based experiment was performed. The results of these experiments were additionally modelled using COMSOL Multiphysics. The results have been presented at the conference. T2 - Advanced Infrared Technology and Applications (AITA) 2025 CY - Kobe, Japan DA - 15.09.2025 KW - Thermography KW - Thermografie KW - Wind turbine rotor blades KW - Windenergie Anlage Rotorblätter KW - FEA PY - 2025 AN - OPUS4-64222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro A1 - Krankenhagen, Rainer A1 - Lapšanská, Ivana A1 - Stamm, Michael T1 - WTB-IRT: Modelling and Measurement of Thermal Contrast in Wind Turbine Rotor Blades (WTBs) N2 - The rapid growth of wind energy infrastructure over the past two to three decades has led to an urgent need for advanced non-destructive testing (NDT) methods—both for newly installed wind turbine blades (WTBs) and for ageing components nearing the end of their service life. Among emerging techniques, passive infrared thermography (IRT) offers a promising solution by enabling contactless, time-efficient inspection based on naturally occurring thermal variations. The effectiveness of passive IRT depends on the presence of sufficient thermal contrast to distinguish surface features, subsurface structures, and defects. To better understand the possibility of obtaining such contrast in composite structures such as WTBs, a controlled study was carried out on a blade section exposed to programmed temperature transients in a climate chamber. Infrared measurements were recorded, and the thermal behaviour of the specimen was simulated using finite element models (FEM) in COMSOL Multiphysics 6.3. Although direct validation is limited by measurement uncertainties and transient effects, the comparison provides insight into the capabilities and limitations of FEM in replicating real-world thermal behaviour. This paper focuses specifically on the challenges related to the modelling approach. T2 - 18th International Workshop on Advanced Infrared Technology and Applications (AITA 2025) CY - Kobe, Japan DA - 15.09.2025 KW - Thermography KW - Wind energy KW - Wind turbine rotor blades KW - Windenergie Anlage Rotorblätter KW - FEA PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-642308 DO - https://doi.org/10.3390/proceedings2025129015 VL - 129 IS - 1 SP - 1 EP - 5 PB - MDPI CY - Basel AN - OPUS4-64230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scheuschner, Nils A1 - Altenburg, Simon A1 - Pignatelli, Giuseppe A1 - Maierhofer, Christiane A1 - Straße, Anne A1 - Gornushkin, Igor B. A1 - Gumenyuk, Andrey T1 - Vergleich der Messungen der Schmelzbadtemperatur bei der Additiven Fertigung von Metallen mittels IR-Spektroskopie und Thermografie T1 - Comparison of measurements of the melt pool temperature during the additive production of metals by means of IR spectroscopy and thermography N2 - Im Rahmen des Themenfeldprojektes „Process Monitoring of AM“ (ProMoAM) evaluiert die Bundesanstalt für Materialforschung und -Prüfung (BAM) gegenwärtig die Anwendbarkeit verschiedenster ZfP-Verfahren zur in-situ Prozessüberwachung in der additiven Fertigung (AM) von Metallen in Hinblick auf die Qualitätssicherung. Einige der wichtigsten Messgrößen sind hierbei die Temperatur des Schmelzbades und die Abkühlrate, welche starken Einfluss auf das Gefüge und die Eigenspannung haben. Aufgrund der Zugänglichkeit zum Werkstück während des Bauprozesses bieten sich optische Verfahren zu Temperaturbestimmung an. Hierbei stellen jedoch u. a. die hohe Bandbreite der zu messenden Temperaturen, die Bestimmung der Emissivität und ihre Änderung bei Phasenübergängen der verwendeten Legierung große experimentelle Herausforderungen dar. Eine weitere Herausforderung stellt für die IR-Spektroskopie die Absorption durch das Schutzgas und weitere optische Elemente dar. Um diese auch in einem industriellen Umfeld kompensieren zu können, wurde eine Methode entwickelt, die das gemessene Spektrum bei der Verfestigung des Werkstoffes als Referenz nutzt. In diesem Beitrag wird die Anwendung dieser Methode für die IR-Spektrometrie als auch Thermografische Messungen beim Laser-Pulver-Auftragschweißen von 316L gezeigt, wobei beide Methoden weiterhin in Hinblick auf ihre individuellen Vor- und Nachteile miteinander verglichen werden. N2 - Within the topic area project “Process Monitoring of AM” (ProMoAM) the Federal Institute for Materials Research and Testing is currently evaluating the applicability of various NDT methods for in-situ process Monitoring in the additive manufacturing (AM) of metals with regard to quality assurance. Two of the most important variables to measure are the temperature of the molten pool and the cooling rate, which have a strong influence on the microstructure and the residual stress. Due to the accessibility of the workpiece during the construction process, optical methods for temperature determination are suitable. However, the wide range of temperatures to be measured, the determination of emissivity and its change during phase transitions of the alloy pose great experimental challenges. Another challenge for IR spectroscopy is the absorption by the inert gas and other optical elements. In order to be able to compensate for this in an industrial environment, a method was developed which uses the measured spectrum as a reference when the material is solidified. This paper shows the application of this method for IR spectrometry as well as thermographic measurements during laser powder cladding of 316L. Furthermore both methods are compared with respect to their individual Advantages and disadvantages. KW - Laser-Pulver-Auftragschweißen KW - Thermografie KW - Direct Energy Deposition KW - IR-Spektroskopie KW - Additive Fertigung KW - Laser metal deposition KW - Thermography KW - IR-spectroscopy KW - Additive manufacturing PY - 2021 DO - https://doi.org/10.1515/teme-2021-0056 VL - 88 IS - 10 SP - 626 EP - 632 PB - De Gruyter CY - Oldenburg AN - OPUS4-52987 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Lecompagnon, Julien A1 - Hassenstein, Christian A1 - Thiel, Erik A1 - Pech May, Nelson Wilbur T1 - Using spatial and temporal shaping of laser-induced diffuse thermal wave fields in thermography N2 - The diffuse nature of thermal waves is a fun-damental limitation in thermographic nonde-structive testing. In our studies we investigated different approaches by shaping the thermal wave fields which result from heating. We have used high-power laser sources to heat metallic samples. Using these spatial and temporal shaping techniques leads to a higher detection sensitivity in our measurements with the infra-red camera. In this contribution we show our implementation of shaping laser-induced diffuse thermal wave fields and the effect on the defect reconstruction quality. T2 - SMSI 2020 Conference CY - Online meeting DA - 22.06.2020 KW - Thermal wave KW - Diffusion KW - High-power laser KW - Thermography KW - Spatiotemporal shaping PY - 2020 DO - https://doi.org/10.5162/SMSI2020/C5.1 SP - 179 EP - 180 AN - OPUS4-50897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Towards the in-service blade inspection by ground-based passive thermography N2 - Until today, the optical inspection of rotor blades by industrial climbers is considered state of the art. However, both more and larger rotor blades and the increasing digitalization of maintenance work make modern inspection methods increasingly necessary. In this context, passive thermography can serve as a useful digital technique for in-service inspection of wind turbine blades. Unlike active thermography, this inspection method does not require an active heat source but takes advantage of heating by the sun and diurnal temperature fluctuations. This allows inspections from the ground during operation and does not require shutting down the wind turbine. However, an inspection with passive thermography is highly weather dependent. Thus, the already weak thermal signatures formed due to internal structures and possible internal damage are only strong enough under certain weather conditions. To obtain meaningful inspection results despite the relatively small thermal differences between intact and defective components, three aspects are crucial: 1. Measurements should be taken at the time of optimum weather conditions. It must be kept in mind that different internal damage will be revealed by thermal signatures under different weather conditions. 2. The thermal signature of the rotor blades, including possible damages, must be simulated with FEM simulations. In this way, the influence of different weather conditions can be predicted but also understood in the aftermath. 3. The temperature differences between identically designed and assembled rotor blades must be considered to analyze variations between blades. This work will address all these aspects and show, based on field measurements under industrial conditions (exemplarily shown in figure 1), laboratory measurements and FEM simulations, which steps must be taken to establish passive thermography as an industrial inspection method. T2 - EERA SP7 Rotor Blade workshop CY - Roskilde, Denmark DA - 23.06.2022 KW - Thermography KW - Wind energy KW - Maintenance KW - Rotor blades KW - Passive IRT PY - 2022 AN - OPUS4-55819 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon T1 - Towards hyperspectral in-situ temperature measurement in metal additive manufacturing N2 - The industrial use of additive manufacturing for the production of metallic parts with high geometrical complexity and lot sizes close to one is rapidly increasing as a result of mass individualisation and applied safety relevant constructions. However, due to the high complexity of the production process, it is not yet fully understood and controlled, especially for changing (lot size one) part geometries. Due to the thermal nature of the Laser-powder bed fusion (L-PBF) process – where parts are built up layer-wise by melting metal powder via laser - the properties of the produced part are strongly governed by its thermal history. Thus, a promising route for process monitoring is the use of thermography. However, the reconstruction of temperature information from thermographic data relies on the knowledge of the surface emissivity at each position on the part. Since the emissivity is strongly changing during the process due to phase changes, great temperature gradients, possible oxidation, and other potential influencing factors, the extraction of real temperature data from thermographic images is challenging. While the temperature development in and around the melt pool, where melting and solidification occur is most important for the development of the part properties. Also, the emissivity changes are most severe in this area, rendering the temperature deduction most challenging. A possible route to overcome the entanglement of temperature and emissivity in the thermal radiation is the use of hyperspectral imaging in combination with temperature emissivity separation (TES) algorithms. As a first step towards the combined temperature and emissivity determination in the L-PBF process, here, we use a hyperspectral line camera system operating in the short-wave infrared region (0.9 µm to 1.7 µm) to measure the spectral radiance emitted. In this setup, the melt pool of the L-PBF process migrates through the camera’s 1D field of view, so that the radiation intensities are recorded simultaneously for multiple different wavelength ranges in a spatially resolved manner. At sufficiently high acquisition frame rate, an effective melt pool image can be reconstructed. Using the grey body approximation (emissivity is independent of the wavelength), a first, simple TES is performed, and the resulting emissivity and temperature values are compared to literature values. Subsequent work will include reference measurements of the spectral emissivity in different states allowing its analytical parametrisation as well as the adaption and optimisation of the TES algorithms. An illustration of the proposed method is shown in Fig.1. The investigated method will allow to gain a deeper understanding of the L-PBF process, e.g., by quantitative validation of simulation results. Additionally, the results will provide a data basis for the development of less complex and cheaper sensor technologies for L-PBF in-process monitoring (or for related process), e.g., by using machine learning. T2 - 21st International Conference on Photoacoustic and Photothermal Phenomena CY - Bled, Slovenia DA - 19.06.2022 KW - Thermography KW - Additive manufacturing KW - L-PBF KW - Hyperspectral PY - 2022 AN - OPUS4-55152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Towards automated passive thermography of wind turbine blades N2 - Up to now, the inspection of wind turbines by industrial climbers has been considered "state of the art". However, many aspects like ever-larger wind turbines, minimizing the risk for man and machine and the advancing digitalization make modern and automated inspection methods indispensable. A particular interest here is contactless and remote methods that can be used with drones instead of climbing robots. The work presented here contributes to the long-term goal of making autonomous and advanced inspections of wind turbine rotor blades using drones ready for industrial use. Besides visual inspection, only a few inspection methods are capable of non-contact inspection on an industrial scale. Passive thermography can serve as such a contactless and digital inspection method and is well known for its applications in the inspection of buildings or electrical circuits. It can even sense both near-surface and subsurface defects. The sensitivity to subsurface defects makes one advantage of thermography over visual inspections. As a digital inspection method, it is generally also more objective and offers more comparability. For example, defects and their extent can be easily monitored and compared over time. However, its industrial application relies on thermal gradients in the inspected object such that a temperature contrast exists between damaged and sound areas. This also applies to large unheated structures such as wind turbine rotor blades, which do not have an intrinsic temperature gradient and at the same time cannot be easily heated externally. Under certain weather conditions, a change of the environmental temperature or the solar loading conditions can provide the necessary thermal gradients to make passive thermography viable for the in-service inspection of rotor blades. For a reliable use of passive thermography on "thermal passive" components, the incorporation of these environmental conditions in the planning and evaluation of thermal inspections is crucial. Compared to many other objects and buildings, wind turbine blades have varying and often unknown complex internal structures depending on the model. A special method is therefore required, that can be used independently of the internal structure of the blades and that relates the individual thermograms of the three rotor blades to each other. This allows the distinction between the thermal response of design-specific structural features and damages or irregularities between the three blades. In this work we present thermal signatures of rotating in-service rotor blades taken under industrial relevant conditions. These thermograms show surface and subsurface damages and irregularities which we contrast with structural design features by referencing the three blades to each other. In addition, we examine the strong influence of different weather conditions on the inspection results. A direct comparison of measured results with inspection reports from industrial climbers serves as a benchmark. T2 - EERA DeepWind conference CY - Trondheim, Norway DA - 19.01.2022 KW - Thermography KW - Wind energy KW - Passve IR KW - Rotor blades KW - Maintenance PY - 2022 AN - OPUS4-55818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro A1 - Purayil, Sruthi Krishna Kunji A1 - Kruse, Julius A1 - Madia, Mauro A1 - Nielsen, Sören T1 - Thermography-Assisted Mechanical Testing of Cold-Spray (AM) Repair N2 - Cold Spray Additive Manufacturing (CSAM) is a solid-state process that is being increasingly used for structural repairs in aerospace and energy sectors. It enables the deposition of dense material at low temperatures by accelerating metal particles to supersonic velocities, thereby reducing thermal distortion. However, the structural integrity of CSAM repairs—particularly at the interface between the deposited layer and the substrate—remains a critical concern. Various post-treatments and characterization methods have been explored to optimize performance. While X-ray Computed Tomography (XCT) is effective for sub-surface inspection, it cannot be applied in situ during mechanical testing. Digital Image Correlation (DIC), a surface-based method, also lacks sub-surface sensitivity. To address this, Infrared Thermography (IRT) was employed alongside DIC during the tensile and fatigue testing of aluminum CSAM-repaired specimens. A cooled IRT camera operating at 200 FPS captured thermal data, with lock-in processing subsequently applied in post-processing. IRT successfully detected early interfacial damage and enabled the tracking of crack propagation, which was later confirmed through fracture surface analysis. This extended abstract presents findings from fatigue tests using IRT. T2 - 18th International Workshop on Advanced Infrared Technology and Applications (AITA 2025) CY - Kobe, Japan DA - 15.09.2025 KW - Thermography KW - Thermografie KW - Thermal stress analysis KW - Cold spray KW - Damage detection PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-642299 DO - https://doi.org/10.3390/proceedings2025129018 VL - 129 IS - 1 SP - 1 EP - 5 PB - MDPI CY - Basel AN - OPUS4-64229 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaudhuri, Somsubhro T1 - Thermography-Assisted Mechanical Testing of Cold-Spray (AM) Repair N2 - Cold Spray Additive Manufacturing (CSAM) is a solid-state process that is being increasingly used for structural repairs in aerospace and energy sectors. It enables the deposition of dense material at low temperatures by accelerating metal particles to supersonic velocities, thereby reducing thermal distortion. However, the structural integrity of CSAM repairs—particularly at the interface between the deposited layer and the substrate—remains a critical concern. Various post-treatments and characterization methods have been explored to optimize performance. While X-ray Computed Tomography (XCT) is effective for sub-surface inspection, it cannot be applied in situ during mechanical testing. Digital Image Correlation (DIC), a surface-based method, also lacks sub-surface sensitivity. To address this, Infrared Thermography (IRT) was employed alongside DIC during the tensile and fatigue testing of aluminum CSAM-repaired specimens. A cooled IRT camera operating at 200 FPS captured thermal data, with lock-in processing subsequently applied in post-processing. IRT successfully detected early interfacial damage and enabled the tracking of crack propagation, which was later confirmed through fracture surface analysis. T2 - Advanced Infrared Technology and Applications (AITA) 2025 CY - Kobe, Japan DA - 15.09.2025 KW - Thermography KW - Thermografie KW - Thermal stress analysis KW - Cold spray KW - Damage detection PY - 2025 AN - OPUS4-64227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon A1 - Scheuschner, Nils A1 - Maierhofer, Christiane A1 - Mohr, Gunther A1 - Hilgenberg, Kai T1 - Thermography in laser powder bed fusion of metals: time over threshold as feasible feature in thermographic data N2 - Thermography is one on the most promising techniques for in-situ monitoring of metal additive manufacturing processes. Especially in laser powder bed fusion processes, the high process dynamics and the strong focus of the laser beam cause a very complex thermal history within the produced specimens, such as multiple heating cycles within single layer expositions. This complicates data interpretation, e.g., in terms of cooling rates. A quantity that is easily calculated is the time a specific area of the specimen is at a temperature above a chosen threshold value (TOT). Here, we discuss variations occurring in time-over-threshold-maps during manufacturing of an almost defect free cuboid specimen. T2 - 15th Quantitative InfraRed Thermography conference CY - Online meeting DA - 21.09.2020 KW - Additive Manufacturing KW - Process monitoring KW - Thermography KW - L-PBF KW - Time over threshold PY - 2020 DO - https://doi.org/10.21611/qirt.2020.005 SP - 1 EP - 5 PB - QIRT Council CY - Quebec, Canada AN - OPUS4-52014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -