TY - CONF A1 - Munsch, Sarah Mandy A1 - Strangfeld, Christoph A1 - Kruschwitz, Sabine T1 - Interpretation of NMR signals from partly saturated sandstones N2 - The development of prevention methods and the detection of moisture related damages in buildings and transport infrastructure at an early stage are current issues in the field of non-destructive testing in civil engineering. Especially the subject of partial saturation requires further research since it is more likely to occur than full saturation of the material. In fact, partial saturation in porous media is even more complicated because both fully and partly saturated pores (i.e. pores in which the surfaces are covered with thin water layers) are present. As the non-destructive method nuclear magnetic resonance (NMR) enables the measurement and quantification of relative low moisture contents, it is suitable for the investigation of partly saturated porous building materials. Nevertheless, the differentiation between partly and fully saturated pores is still a challenge. Therefore, in this study, we investigate two sandstones types (Bozanov and Schönbrunner sandstone) at various defined saturation states by using NMR. Furthermore, we measure the relative humidities within the samples and compute the water layer thicknesses (WLT) along the pore walls of all pore sizes to calculate the corresponding degree of pore saturation. To finally assign the NMR signals to pore sizes and to differentiate between partly and fully saturated pores, the water content distribution obtained from the WLT calculation is used for calibration of the relaxation-time distribution. In this extended abstract, selected results only for Schönbrunner sandstone are presented. T2 - ISEMA 2021 CY - Online meeting DA - 26.07.2021 KW - NMR KW - Relative humidity KW - Water layer thickness KW - Partial pore saturation KW - Pore-size distribution PY - 2021 SN - 978-1-7281-8736-5 VL - 2021 SP - 111 EP - 115 PB - IEEE AN - OPUS4-53045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Munsch, Sarah Mandy A1 - Strangfeld, Christoph A1 - Kruschwitz, Sabine T1 - Möglichkeiten und Grenzen der zerstörungsfreien Erfassung niedriger Feuchtegehalte in teilgesättigten Sandsteinen mit 1H-NMR N2 - Die zerstörungsfreie Ermittlung der Materialfeuchte in Baustoffen ist für das Bauwesen von großer Bedeutung, denn ein erhöhter Feuchteeintrag kann zu Schimmelbildung, Alkali-Kieselsäure-Reaktionen, Korrosion etc. führen und somit ein hohes Schadenspotential mit sich bringen. Auch wenn zur qualitativen Lokalisierung möglicher Schad- und Risikostellen bereits zahlreiche zerstörungsfreie Verfahren in der Praxis Anwendung finden, besteht ein Mangel an quantitativen Verfahren, die auch bei niedrigen Feuchtegehalten sensitiv sind. Eine Methode zur zerstörungsfreien und quantitativen Bestimmung des Feuchtegehaltes und der effektiven Porosität ist die 1H-Kernspinresonzanzmethode (NMR). Da NMR sensitiv für die molekulare Beweglichkeit von Wasserstoffprotonen ist, lassen sich Informationen über die Bindungsform und -stärke sowie der Umgebung (Porengröße und Mineralzusammensetzung) der Wasserstoffprotonen gewinnen. Obwohl es bereits seit über 20 Jahren mobile NMR-Messeräte gibt, wird NMR heutzutage immer noch weitestgehend im Labor eingesetzt. Dies liegt daran, dass sie aufgrund der verwendeten Permanentmagnete schwer sind und nur äußerst geringe Eindringtiefen ermöglichen. In einer derzeit laufenden Forschungsarbeit wird deshalb ein speziell für Bohrkerne entworfener NMR-Tomograph eingesetzt. Mit seiner minimalen Echozeit von 50 µs lässt sich (abhängig von der Oberflächenrelaxivität) Wasser bis in nanometergroßen Poren erfassen. Um die Sensitivität von NMR bei Teilsättigung zu untersuchen, wurden verschiedene Sandsteinproben in Exsikkatoren mit relativen Luftfeuchten im Bereich von 33 % bis 96 % gelagert. Als Referenzen dienen zum einen das NMR-Signal bei Vollsättigung und zum anderen die Porengrößenverteilung aus Quecksilberporosimetriemessungen (MIP). Um die NMR-Sensitivität zu bewerten, wird die Korrelation der NMR-Amplitude mit den gravimetrisch ermittelten Feuchtegehalten sowie ein Vergleich der Porosität aus NMR und MIP betrachtet. Zu beachten ist in diesem Zusammenhang, dass sowohl die Reduzierung der Wasserfilmdicke als auch die Verkleinerung von Porengrößen zu einer ähnlichen Verkürzung der T2-Relaxationszeit führt. Als Ausblick wird ein Lösungsansatz vorgestellt, bei dem die NMR-Signale mit der Wasserfilmdickenberechnung basierend auf der relativen Luftfeuchte im Material korreliert werden. T2 - 81. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Online meeting DA - 01.03.2021 KW - NMR KW - Sandsteine KW - Porosität KW - Oberflächenrelaxivität KW - Feuchtegehalt PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-522271 DO - https://doi.org/10.23689/fidgeo-3957 N1 - Geburtsname von Munsch, Sarah Mandy: Nagel, S. M. - Birth name of Munsch, Sarah Mandy: Nagel, S. M. AN - OPUS4-52227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Petryna, Y. T1 - Damage assessment of civil structures using wave propagation analysis and transmissibility functions N2 - This presentation shows the applicaiton of seismic interferometry to vibration recordings. The Normalized-Input-Output-Minimization (NIOM) method to reconstruct the virtual impulse wave propagation is introduced. We obtain wave velocities and transmissibility functions and consider them as reference values for the damage detection method. At the end, the evaluation results are presented by two examples: a 14-story RC building and a 64 m long pedestrian bridge. T2 - EVACES2021 9th International Conference on Experimental Vibration Analysis for Civil Engineering Structures CY - Online meeting DA - 14.09.2021 KW - Damage detection KW - Damage indices KW - Normalized-Input-Output-Minimization KW - Transmissibility function KW - Wave propagation PY - 2021 AN - OPUS4-53437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Johann, Sergej A1 - Baensch, Franziska A1 - Strurm, Patrick A1 - Tiebe, Carlo A1 - Pötschke, Samuel A1 - Lay, Vera ED - Hall, H. T1 - HF RFID-based Measurement Comparison for Method Optimization in M2 Concrete and Alkali-Activated Mortars N2 - The internal project "SealWasteSafe" of the Federal Institute for Materials Research and Testing is dedicated to the further improvement in the construction of sealing systems for underground repositories of radioactive waste. Particularly, a multi-sensory concept is developed to ensure quality assurance and continuous long-term monitoring on the engineered barriers. Therefore, beside other measures, the temperature and equilibrium moisture of the construction shall be monitored and respective multi-sensoric monitoring concepts are tested first on the laboratory scale. One focus in this project is on embedded application in alkali-activated mortars (AAM), which results in special requirements for the resistance of the sensors to strongly alkaline environments with up to pH 14. In addition, the ingress of water along cables or at sensor positions is critical for sensors embedded in concrete, as the cable access of the sensor housing is a major weak point. It is therefore advisable to equip wireless high frequent radio frequency identification-based sensors, so called HF RFID sensors (short: RFID), that do not require cable access and thus have a stable and leak-proof sensor housing for long-term monitoring. In this contribution, the results from temperature, moisture and transmitted power monitoring of a AAM and a M2 specimens by means of HF RFID sensor systems are presented. T2 - 35th Danubia - Adria Symposium on Advances in Experimental Mechanics CY - Linz, Österreich DA - 21.09.2021 KW - Passive sensor interface KW - RFID KW - Structural Health Monitoring KW - Alkali-Activated Mortars PY - 2021 SN - 978-3-9504997-0-4 SP - 116 EP - 117 AN - OPUS4-53397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Johann, Sergej A1 - Baensch, Franziska A1 - Sturm, Patrick A1 - Tiebe, Carlo A1 - Pötschke, Samuel A1 - Lay, Vera T1 - HF RFID-based Measurement Comparison for Method Optimization in M2 Concrete and Alkali-Activated Mortars N2 - The internal project "SealWasteSafe" of the Federal Institute for Materials Research and Testing is dedicated to the further improvement in the construction of sealing systems for underground repositories of radioactive waste. Particularly, a multi-sensory concept is developed to ensure quality assurance and continuous long-term monitoring on the engineered barriers. Therefore, beside other measures, the temperature and equilibrium moisture of the construction shall be monitored and respective multi-sensoric monitoring concepts are tested first on the laboratory scale. One focus in this project is on embedded application in alkali-activated mortars (AAM), which results in special requirements for the resistance of the sensors to strongly alkaline environments with up to pH 14. In addition, the ingress of water along cables or at sensor positions is critical for sensors embedded in concrete, as the cable access of the sensor housing is a major weak point. It is therefore advisable to equip wireless high frequent radio frequency identification-based sensors, so called HF RFID sensors (short: RFID), that do not require cable access and thus have a stable and leak-proof sensor housing for long-term monitoring. In this contribution, the results from temperature, moisture and transmitted power monitoring of a AAM and a M2 specimens by means of HF RFID sensor systems are presented. T2 - 35th Danubia - Adria Symposium on Advances in Experimental Mechanics CY - Linz, Austria DA - 21.09.2021 KW - Passive sensor interface KW - RFID KW - Structural Health Monitoring KW - Alkali-Activated Mortars PY - 2021 AN - OPUS4-53398 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Bühling, Benjamin A1 - Maack, Stefan T1 - Adaption of fluidic devices for SHM of hydrogen tanks N2 - Frequency analysis of the tank during every filling Passive actuator is integrated inside filling nozzle/ pressure vessel Frequency from 5 kHz to 150 kHz Frequency sweep (Chirp) can be performed Works with every fluid: air, hydrogen, oxygen, argon, water. T2 - H2Safety Kompetenzzentrum CY - BAM Berlin, Germany DA - 07.07.2021 KW - Fluidic device KW - Structural health monitoring KW - Hydrogen tank KW - Ultrasound PY - 2021 AN - OPUS4-52930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Hille, Falk A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst T1 - Monitoring of a prestressed bridge model by ultrasonic measurement and vibration recordings N2 - Nowadays, civil engineers have applied prestressing technique to long span bridges to enhance the structural strength and to improve the structural performance in their life time. However, it‘s not easy to avoid prestress loss during the construction or in service time. This problem will influence the function of the structures and worse make our life in danger. Therefore, it‘s important to focus on the topic „bridge monitoring“ to make sure the structural property is "health". This presentation introduces the work which fulfills the research goal - birdge monitoring. A large-scale prestressed concrete bridge model was considered in this work. We obteined various damaged condition due to the different prestressed levels which we can change every time in the experiment. The experimental measurement in two scales were demonstrated by ultrasonics and natural vibration of the bridge. T2 - COMPDYN 2021 8th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering CY - Online meeting DA - 28.06.2021 KW - Bridge monitoring KW - Prestressed concrete bridge KW - Ultrasonic KW - Natural vibration PY - 2021 AN - OPUS4-52955 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan T1 - CASPAR - FKZ: 19F2178A "Plattform für die beweissichere und rückführbare Datennutzung im Bauwesen" N2 - Bestandsunterlagen von älteren Bauwerken sind oft nicht in ausreichendem Umfang verfügbar. Soll jedoch der Zustand von z.B. Gebäude oder Brücken bewertet werden, stellen Bestandsunterlagen die Grundlage dafür dar. Ansonsten muss die Bauweise des Bauwerkes kostenintensiv nachvollzogen und mit nachträglichen Untersuchungsverfahren bewertet werden. Heute spielt die digitale Planung im Bauwesen eine immer größere Rolle und Bauvorhaben werden in sogenannten BIM Modellen (Building Information Modelling) geplant. Diese Daten müssen langfristig und manipulationssicher gespeichert werden. In diesem Projekt erarbeiten wir die technologischen Grundlagen, um Daten effizient und sicher zu speichern. Wir erarbeiten eine digitale Schnittstelle, um Daten aus unterschiedlichsten Quellen sicher zusammenzuführen und Informationen semantisch zu verknüpfen. Um den Nachweis für die Nutzbarkeit unserer Technologie zu erbringen, entwickeln wir im Rahmen des beantragten Projekts eine prototypische objektbezogene Datenablage in Form eines Demonstrators, in die digitale Informationen einer realen Brücke überführt werden. T2 - Online-Fachaustausch der mFUND-Begleitforschung Move Mobility | iRights.Lab CY - Online meeting DA - 07.05.2021 KW - Digitalisierung KW - Messdaten KW - Brücken KW - Qualitätssicherung KW - Bauwesen PY - 2021 AN - OPUS4-53221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wang, Xin A1 - Niederleithinger, Ernst A1 - Hindersmann, Iris T1 - The installation of embedded ultrasonic transducers inside a bridge to monitor temperature and load influence using coda wave interferometry technique N2 - This article presents a unique method of installing a special type of embedded ultrasonic transducers inside a 36-m-long section of an old bridge in Germany. A small-scale load test was carried out by a 16 ton truck to study the temperature and load influence on the bridge, as well as the performance of the embedded transducers. Ultrasonic coda wave interferometry technique, which has high sensitivity in detecting subtle changes in a heterogeneous medium, was used for the data evaluation and interpretation. The separation of two main influence factors (load effect and temperature variation) is studied, and future applications of wave velocity variation rate Φ for structural health condition estimation are discussed. As a preliminary research stage, the installation method and the performance of the ultrasonic transducer are recognized. Load- and temperature-induced weak wave velocity variations are successfully detected with a high resolution of 10−4%. The feasibility of the whole system for long-term structural health monitoring is considered, and further research is planned. KW - Ultrasound KW - Bridge KW - Monitoring KW - coda wave interferometry KW - embedded PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-527978 DO - https://doi.org/10.1177/14759217211014430 SN - 1475-9217 VL - 21 IS - 3 SP - 913 EP - 927 PB - SAGE AN - OPUS4-52797 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph T1 - Quantification of the Knudsen Effect on the Effective Gas diffusion Coefficient in Partially Saturated Pore Distributions N2 - The effective gas diffusion coefficient describes the process of gas diffusion in porous materials. Several materials have a significant number of micropores in the lower nanometre range leading to a reduction of gas diffusion (Knudsen effect). In the case of partial pore saturation during adsorption, the available pore space is further reduced, as is the gas diffusion. In this study, the influence of partially saturated pores on the Knudsen effect and on the gas diffusion is quantified. Three different pore geometries are investigated (slit, cylindrical and spherical pores) and three different types of pore size distribution, including a broad equal distribution, three narrow normal distributions and two measured distributions of concrete. Besides the intensive computation of the exact pore saturation, a simplified model with low computational requirements is suggested. This study shows that the influence of the water layer thickness on the effective diffusion becomes significant for pore radii below 50 nm and the assumed pore geometry is important. At the end, the overall effect is quantified for an amorphous material with most pore radii below 30 nm. At a moisture level of 50% relative humidity, the effective diffusion is reduced by 35% due to partial saturation. KW - Effective gas diffusion coefficient KW - Gas transport in porous media KW - Knudsen diffusion KW - Moisture transport KW - Nanopores PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-528509 DO - https://doi.org/10.1002/adem.202100106 VL - 23 IS - 10 SP - 2100106 PB - Wiley AN - OPUS4-52850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lay, Vera A1 - Buske, S. A1 - Kleine, F. A1 - Townend, J. A1 - Kellett, R. A1 - Savage, M. A1 - Schmitt, D. R. A1 - Constantinou, A. A1 - Eccles, J. A1 - Lawton, D. A1 - Bertram, M. A1 - Hall, K. A1 - Kofman, R. A1 - Gorman, A. T1 - 3D seismic imaging of the Alpine Fault and the glacial valley at Whataroa, New Zealand N2 - The Alpine Fault at the West Coast of the South Island (New Zealand) is a major plate boundary that is expected to rupture in the next 50 years, likely as a magnitude 8 earthquake. The Deep Fault Drilling Project (DFDP) aimed to deliver insight into the geological structure of this fault zone and its evolution by drilling and sampling the Alpine Fault at depth. Here we present results from a seismic survey around the DFDP-2 drill site in the Whataroa Valley where the drillhole almost reached the fault plane. This unique 3D seismic survey includes several 2D lines and a 3D array at the surface as well as borehole recordings. Within the borehole, the unique option to compare two measurement systems is used: conventional three-component borehole geophones and a fibre optic cable (heterodyne Distributed Vibration Sensing system (hDVS)). Both systems show coherent signals but only the hDVS system allowed a recording along the complete length of the borehole. Despite the challenging conditions for seismic imaging within a glacial valley filled with sediments and steeply dipping valley flanks, several structures related to the valley itself as well as the tectonic fault system are imaged. The pre-processing of the seismic data also includes wavefield separation for the zero-offset borehole data. Seismic images are obtained by prestack depth migration approaches. Within the glacial valley, particularly steep valley flanks are imaged directly and correlate well with results from the P-wave velocity model obtained by first arrival travel-time tomography. Additionally, a glacially over-deepened trough with nearly horizontally layered sediments is identified about 0.5 km south of the DFDP-2B borehole. With regard to the expected Alpine fault zone, a set of several reflectors dipping 40-56° to the southeast are identified in a ~600 m wide zone between depths of 0.2 and 1.2 km that is interpreted to be the minimum extent of the damage zone. Different approaches image one distinct reflector dipping at 40°, which is interpreted to be the main Alpine Fault reflector. This reflector is only ~100 m ahead from the lower end of the borehole. At shallower depths (z<0.5 km), additional reflectors are identified as fault segments and generally have steeper dips up to 56°. About 1 km south of the drill site, a major fault is identified at a depth of 0.1-0.5 km that might be caused by the regional tectonics interacting with local valley structures. A good correlation is observed among the separate seismic data sets and with geological results such as the borehole stratigraphy and the expected surface trace of the fault. In conclusion, several structural details of the fault zone and its environment are seismically imaged and show the complexity of the Alpine Fault at the Whataroa Valley. Thus, a detailed seismic characterization clarifies the subsurface structures, which is crucial to understand the transpressive fault’s tectonic processes. T2 - EGU 2021 General Assembly CY - Online meeting DA - 19.04.2021 KW - Imaging KW - Signal processing KW - Seismic KW - Borehole KW - DAS PY - 2021 AN - OPUS4-52614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Towards digital tools for waste package and facility monitoring and prediction N2 - To provide better means for a safe and effective monitoring of cemented waste packages including prediction tools to assess the future integrity development during pre-disposal activities, several digital tools are evaluated and improved in the frame of the EC funded project PREDIS. Safety enhancement (e. g. less exposure of testing personnel) and cost effectiveness are part of the intended impact. The work includes but is not limited to inspection methods such as muon imaging, wireless sensors integrated into waste packages as well as external package and facility monitoring such as remote fiber optical sensors. The sensors applied will go beyond radiation monitoring and include Proxy parameters important for long term integrity assessment (e. g. internal pressure). Sensors will also be made cost effective to allow the installation of much more sensors compared to current practice. The measured data will be used in digital twins of the packages for specific simulations (geochemical, integrity) providing a prediction of future behavior. Machine Learning techniques trained by the characterization of older packages will help to connect the models to the actual data. All data (measured and simulated) will be collected in a joint data base and connected to a decision framework to be used at actual facilities. The presentation includes detailed information about the various tools under consideration, their connection and first results of our research. T2 - DigiDecom 2021 DIGITAL – Online event focusing on innovation within nuclear decommissioning CY - Online Meeting DA - 23.03.2021 KW - Radioactive waste KW - Waste package KW - Monitoring KW - Digital twin PY - 2021 AN - OPUS4-52622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man T1 - Investigation of ambient noise seismological methods on a bridge model N2 - Structural health monitoring is a big issue of the prevention measure for civil structures in the seismic hazard region. The GIOTTO project aims to develop of the real time monitoring in civil engineering by use of the 6 DOFs sensors. This presented work is part of the GIOTTO Project. BAM offered the idea test structure BLEIB bridge for experiment. This prestressed concrete bridge model benefits us to have the various structural condition with different pre-stress. The passive and active monitoring were carried out. The seismic interferometry technique was considered to extract the virtual wave propagation in the structure comparable to the real impulse response excited by the hammer impact. Meanwhile the ultrasonic measurement was performed during the monitoring. The coda wave interferometry (CWI) was applied to investigate the wave velocity variation in two kinds of scale recordings at different prestressed states. The experimental result approves that the seismological noise- based methods are the appropriate evaluation tool for the measurement data. T2 - Seminar WP 2.2 Special Topics in Seismology CY - Online meeting DA - 04.05.2021 KW - Real time monitoring KW - Seismological noise-based methods KW - Coda wave interferometry PY - 2021 AN - OPUS4-52572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Völker, Tobias A1 - Klewe, Tim A1 - Kruschwitz, Sabine T1 - Laser-based building material sorting for the processing of construction and demolition waste for the circular economy N2 - A joint project of partners from industry and research institutions for the research and construction of an analysis system for an automated, sensor-supported sorting of construction and demolition waste will be presented. This is intended to supplement or replace the previously practiced manual sorting, which harbors many risks and dangers for the staff and only enables obvious, visually detectable differences for separation. The method of laser-induced breakdown spectroscopy is to be used in combination with hyperspectral sensors. Due to the jointly processed information (data fusion), this should lead to a significant improvement in the separation of types. In addition to the sorting of different materials (concrete, main masonry building materials, organic components, glass, etc.), impurities such as SO3-containing building materials (gypsum, aerated concrete, etc.) could also be detected and separated. The subsequent recycling and sales opportunities are examined, such as the use of recycled aggregates in concrete, the recycling of building materials containing sulphate as a gypsum substitute for the cement industry or the agglomeration of synthetic lightweight aggregates for lightweight concrete or as a substrate for green roofs. At the same time, it is investigated whether soluble components (sulfates, heavy metals, etc.) can be detected by LIBS without a wet chemical analysis and what impact the recycling materials have on the environment. The entire value chain is examined using the example of the Berlin location in order to minimize economic / technological barriers and obstacles on a cluster level and to sustainably increase the recovery and recycling rates. T2 - Materials Week 2021 CY - Online meeting DA - 07.09.2021 KW - Laser induced breakdown spectroscopy KW - Building waste KW - Circular economy KW - Material sorting PY - 2021 AN - OPUS4-53286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liao, Chun-Man A1 - Petryna, Y. T1 - Damage Assessment of Civil Structures Using Wave Propagation Analysis and Transmissibility Functions N2 - A common damage detection method in civil engineering is to monitor dynamic characteristics such as natural frequencies and modal shapes, which are directly related to the structural stiffness. However, the discrepancy in measured natural frequencies may result from environmental changes, the soil-structure interaction or effects caused by earthquakes. This makes it difficult to decide whether the local change in structural properties is caused by damage or other factors. To address this challenge and thus improve the current damage detection method, the wave propagation analysis method and the transmissibility relationship were considered. In our study, the wave propagation field in structures was reconstructed by applying the Normalized-Input-Output-Minimization (NIOM) method to vibration recordings. Wave velocities and transmissibility functions were considered as reference values for the damage indicators. This paper demonstrates the evaluation of local property changes in two examples of large-scale structures: a 14-story RC building and a 64 m long pedestrian bridge. The proposed damage indicators show a clear correspondence to structural changes. T2 - EVACES2021 9th International Conference on Experimental Vibration Analysis for Civil Engineering Structures CY - Online meeting DA - 14.09.2021 KW - Damage detection KW - Damage indices KW - Normalized-Input-Output-Minimization KW - Transmissibility function KW - Wave propagation PY - 2022 SN - 978-3-030-93235-0 SN - 978-3-030-93236-7 DO - https://doi.org/10.1007/978-3-030-93236-7_2 SP - 3 EP - 13 PB - Springer CY - Cham AN - OPUS4-55565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feistkorn, S. A1 - Algernon, D. A1 - Arndt, R. A1 - Ebell, Gino A1 - Friese, M. A1 - Grosse, C. U. A1 - Holstein, R. A1 - Niederleithiger, Ernst A1 - Schickert, M. A1 - Schulze, S. A1 - Taffe, A. A1 - Walther, A. A1 - Wolf, J. A1 - Zoega, A. A1 - Zwanzig, M. T1 - Introduction to DIN 4871: Qualification of NDT Personnel in Civil Engineering (NDT‐CE) N2 - Recently, non-destructive testing in civil engineering (NDT-CE), in particular of concrete components, has successfully mastered the leap from research to practice. Several methods have been established for field inspections to determine the concrete cover of reinforcement or to estimate the compressive strength as well as other parameters related to the concrete material. In addition, the application of non-destructive testing is indispensable, if information about the inner structure - such as the location of rebars and tendon ducts or the damage-related condition assessment to detect grouting defects, honeycombs, delamination, or corrosion - is required. Besides the selection of a suitable NDT method and an appropriate inspection system, the reliability of the results depends largely on the person who applies the non-destructive inspection technique and evaluates the inspection results. To ensure a high quality of non-destructive concrete evaluation as well as to keep the uncertainty caused by the inspection personnel to a minimum, structured, consistent, and regulated theoretical as well as practical training of inspection personnel is essential. To close this gap, the subcommittee of education and training (UA-A) within the committee for NDT-CE of the German Society for Non-Destructive Testing (DGZfP) has been reactivated in 2018 to establish uniform training standards for non-destructive concrete inspections in the long term. The subcommittee consists of scientists, practitioners, authorities, and clients. So far, the national standard DIN 4871 “Non-destructive testing - Qualification of NDT personnel in Civil Engineering (NDT-CE)” was developed. This standard considers the civil-industry-specifics, for example, that standards for NDT of concrete, as well as related product standards with a few exceptions, still do not exist at the moment. Within this presentation, the concept, the connection to ISO 9712 and other standards as well as an overview of the recently developed German standard DIN 4871 will be presented. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Non-destrucive testing KW - Civil engineering PY - 2022 AN - OPUS4-55526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Büyüksahin, Kaan A1 - Stolpe, Heiko A1 - Lay, Vera T1 - Bore hole probe for ultrasound-based quality control of sealing constructions N2 - Several countries, which use or used nuclear power, started to destruct nuclear power plants. Thus, large amounts of radioactive waste have to be stored safely during the next decades. Large underground caverns will be used a nuclear waste disposal. Once the cavern is full, a sealing construction is required. The sealing should avoid the contact to any fluids or substances of the storage barrels and reduce hazardous radiation. T2 - International Symposium Non-Destructive Testing in Civil Engineering CY - Zurich, Switzerland DA - 16.08.2022 KW - Ultrasonic testing KW - Nuclear waste PY - 2022 AN - OPUS4-55530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, W. A1 - Wilsch, Gerd A1 - Katsumi, N. A1 - Ebell, Gino A1 - Völker, Tobias T1 - Ion distribution in concrete overlay, mapped by laser induced breakdown spectroscopy (LIBS), modified by an embedded zinc anode N2 - Galvanic corrosion protection by embedded zinc anodes is an accepted technique for the corrosion protection of reinforcing steel in concrete. Galvanic currents flow between the zinc anode and the steel reinforcement due to the potential difference that is in the range of a few hundred mV. The ion distribution was studied on two steel reinforced concrete specimens admixed with 3 wt.% chloride/wt. cement and galvanically protected by a surface applied EZ-anode. On both specimens, a zinc anode was embedded and glued to the concrete surface by a geo-polymer-based chloride-free binder. At one specimen, the EZ-anode was operated for 2,5 years, the EZ-anode at the other specimen was not electrically connected to the reinforcement, this specimen serves as a reference. Both specimens have been stored under identical conditions. The ion distribution between the anode (EZ-anode) and cathode (steel reinforcement) was studied by laser-induced breakdown spectroscopy (LIBS) after 7 months, 12 months, and 2,5 years. Results of the LIBS studies on the specimen with activated EZ-anode after 7 months, 12 months, and 2,5 years and of the reference specimen after 2,5 years are reported. Results show that diffusion of ions contributes to the changes in the ion distribution but migration, especially of chlorides towards the EZ-anode is significant despite the weak electric field – several hundred millivolts - generated by the galvanic current. Results show that chloride ions accumulate near the zinc-anode as in water-insoluble zinc-hydroxy chlorides - Simonkolleit. T2 - ICCRRR 2022 CY - Capetown, South Africa DA - 03.10.2022 KW - Korrosion KW - Corrosion KW - LIBS KW - Zinc PY - 2022 AN - OPUS4-55948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Moisture distribution in amorphous porous materials N2 - Mesopores dominate the material moisture and influence the gas diffusion through materials such as concrete or sandstone T2 - Nano@bam Round Table Nano Materials CY - Berlin, Germany DA - 14.10.2022 KW - Physisorption KW - Mesopores KW - Amorphous materials PY - 2022 AN - OPUS4-55998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Fontoura Barroso, Daniel A1 - Niederleithinger, Ernst A1 - Hindersmann, I. A1 - Sodeikat, C. A1 - Groschup, R. T1 - Monitoring of a German Road Bridge Using Embedded Ultrasonic Transducers and Coda Waves N2 - The ‘G¨anstorbr¨ucke’ bridge between the cities of Ulm and Neu-Ulm is one of the best-monitored bridges all over Germany. In addition to an already active bride monitoring system, we have equipped the bridge with 30 ultrasonic transducers to explore the monitoring possibilities at an in-service large-scale reinforced concrete structure with continuous active ultrasonic measurements. The monitoring system is based on the detection of small changes in the entire signal, especially the multiply scattered parts of the recording, the so-called coda. Applying Coda Wave Interferometry (CWI), subtle changes in the signal can be detected and related to changing velocities in the area between source and receiver. A comparison of the results from coda wave interferometry with the strain measurements of the permanent monitoring system shows a correlation between strain measurements and CWI results. We discuss the challenges of changing environmental conditions, pose for interpretation of the results, and highlight the advantages of embedded versus externally attached ultrasonic transducers in permanent bridge monitoring, especially when coda wave interferometry is applied. T2 - EWSHM 2022 CY - Palermo, Italy DA - 04.07.2022 KW - Bridge monitoring KW - Ultrasound KW - Embedded sensors KW - Coda wave interferometry PY - 2022 AN - OPUS4-55383 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -