TY - CONF A1 - Strangfeld, Christoph A1 - Bühling, Benjamin A1 - Maack, Stefan T1 - OsciCheck - A novel fluidic transducer for air coupled ultrasonic measurements N2 - Ultrasonic measurement technology has become indispensable in NDT-CE. Air-coupled ultrasonic (ACU) measurement techniques promise to reduce measurement time. However, the signal quality suffers from large specific impedance mismatch at the transducer-air and air-specimen interface. Additionally, large pressure amplitudes are necessary for the penetration depth required in NDT-CE applications. To address the specific requirements of ultrasonic testing in NDT-CE, a robust ACU transducer was developed, that generates ultrasound by quickly switching a pressurized air flow. The simple design of the fluidic transducer makes the device maintenance free and resilient against harsh environmental conditions. Since the signal is generated by aeroacoustics, there is no specific impedance mismatch between the transducer and the surrounding air. The ultrasonic signal exhibits frequencies in the 30-60 kHz range and is therefore well suited to penetrate heterogenous materials such as concrete. This contribution gives an introduction in the working principle and signal characteristics of the fluidic transducer. A detailed outlook is given to discuss the future potential of fluidic ultrasonic actuators. T2 - International Symposium Non-Destructive Testing in Civil Engineering CY - Zurich, Switzerland DA - 16.08.2022 KW - Air-coupled ultrasound KW - Nondestructive testing KW - Fluidics KW - Bistable amplifier KW - Aeroacoustics PY - 2022 AN - OPUS4-55529 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - On the Treatment of Measurement Uncertainty in Stochastic Modeling N2 - Measurement uncertainty calculations in stochastic moddeling of time-independent, NDT-based random variables to be used in refined assessment of existing structures T2 - International Probabilistic Workshop 2022 (IPW2022) CY - Stellenbosch, South Africa DA - 08.09.2022 KW - Reliability KW - Assessment KW - Existing structures KW - Measurement uncertainty PY - 2022 AN - OPUS4-55657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Towards NDT supported decisions on the reliability of existing bridges N2 - 1) Concept for the NDT-supported assessment of existing structures 2) Demonstration: Shear force analysis of a prestressed concrete bridge T2 - ICOSSAR 2021-2022,13th International Conference on Structural Safety & Reliability CY - Online meeting DA - 13.09.2022 KW - Nachrechnung KW - Zuverlässigkeitsbewertung KW - Messunsicherheit KW - Querkraftnachweis PY - 2022 AN - OPUS4-55796 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - On the accuracy of tendon localization in concrete using ultrasound N2 - Approaches to the development of a (GUM-) measurement model for the calculation of measurement uncertainties in the localization of tendons in concrete structures using the ultrasonic echo method including demonstration were presented. T2 - 6th International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Reliability KW - Measurement Uncertainty KW - Non-Destructive Testing KW - Existing Concrete Structures PY - 2022 AN - OPUS4-55991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Moisture distribution in amorphous porous materials N2 - Mesopores dominate the material moisture and influence the gas diffusion through materials such as concrete or sandstone T2 - Nano@bam Round Table Nano Materials CY - Berlin, Germany DA - 14.10.2022 KW - Physisorption KW - Mesopores KW - Amorphous materials PY - 2022 AN - OPUS4-55998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Bühling, Benjamin A1 - Hauke, M. A1 - Schweitzer, T. A1 - Maack, Stefan T1 - Frequency modulated, air-coupled ultrasound generated by fluidic oscillators N2 - The majority of ultrasonic devices used for non-destructive testing in civil engineering require contact with the surface of the concrete (specimen), which significantly increases the time required for the measurement. This makes it impractical for extensive investigation of large-scale structures such as bridge decks, foundations, or tunnels. In a pioneering approach, fluidic oscillators are used as contact free ultrasonic sources to overcome the aforementioned limitations. These robust and cost-effective actuators require only pressurised air and are ideally suited for harsh environments. At a constant supply pressure, they generate a continuous mono-frequent actuation signal. Further, varying the supply pressure via a fast pressure regulator was found to generate a frequency modulated signal which enabled time-of-flight measurement with an added advantage of increased signal to noise ratio. To demonstrate the feasibility of this novel idea of non-contact ultrasound, the results of the initial tests are presented. T2 - IEEE International Ultrasound Symposium CY - Venice, Italy DA - 11.10.2022 KW - Air-coupled ultrasound KW - Frequency modulation KW - Non-destructive testing KW - Civil engineering KW - Building materials KW - Fluidic oscillators PY - 2022 DO - https://doi.org/10.1109/IUS54386.2022.9958740 SP - 1 EP - 4 AN - OPUS4-56073 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Frequency modulated, air-coupled ultrasound generated by fluidic oscillators N2 - The majority of ultrasonic devices used for non-destructive testing in civil engineering require contact with the surface of the concrete (specimen), which significantly increases the time required for the measurement. This makes it impractical for extensive investigation of large-scale structures such as bridge decks, foundations, or tunnels. In a pioneering approach, fluidic oscillators are used as contact free ultrasonic sources to overcome the aforementioned limitations. These robust and cost-effective actuators require only pressurised air and are ideally suited for harsh environments. At a constant supply pressure, they generate a continuous monofrequent actuation signal. Further, varying the supply pressure via a fast pressure regulator was found to generate a frequency modulated signal which enabled time-of-flight measurement with an added advantage of increased signal to noise ratio. To demonstrate the feasibility of this novel idea of non-contact ultrasound, the results of the initial tests are presented. T2 - IEEE International Ultrasound Symposium CY - Venice, Italy DA - 11.10.2022 KW - Air coupled ultrasound KW - Frequency modulation KW - Non-destructive testing KW - Civil engineering KW - Building materials KW - Fluidic oscillators PY - 2022 AN - OPUS4-56069 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Frequency modulated, air-coupled ultrasound generated by fluidic oscillators N2 - The majority of ultrasonic devices used for non- destructive testing in civil engineering require contact with the surface of the concrete (specimen), which significantly increases the time required for the measurement. This makes it impractical for extensive investigation of large-scale structures such as bridge decks, foundations, or tunnels. In a pioneering approach, fluidic oscillators are used as contact free ultrasonic sources to overcome the aforementioned limi- tations. These robust and cost-effective actuators require only pressurised air and are ideally suited for harsh environments. At a constant supply pressure, they generate a continuous mono- frequent actuation signal. Further, varying the supply pressure via a fast pressure regulator was found to generate a frequency modulated signal which enabled time-of-flight measurement with an added advantage of increased signal to noise ratio. To demonstrate the feasibility of this novel idea of non-contact ultrasound, the results of the initial tests are presented. T2 - IEEE International Ultrasound Symposium CY - Venice, Italy DA - 11.10.2022 KW - Air-coupled ultrasound KW - Frequency modulation KW - Non-destructive testing KW - Civil engineering KW - Building materials KW - Fluidic oscillators PY - 2022 AN - OPUS4-56072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - In situ Prozessüberwachung und Qualitätskontrolle bei der additiven Fertigung von Betonbauteilen N2 - In der additiven Fertigung von Beton wird kontinuierlich Material gemischt und verarbeitet. Dies erfordert eine kontinuierliche in situ Prozessüberwachung und Qualitätskontrolle. An der BAM wurde ein 3D-Betondrucker aufgebaut, der eine umfängliche Prozessüberwachung ermöglicht. Druck-, Temperatur- und Feuchtesensoren in der Pumpe und im Fördersystem erlauben ein kontinuierliches Monitoring des Frischbetons, während ein Laserlinienscanner am Druckkopf unmittelbar die gedruckte Ist-Kontur verfolgt. Die so gewonnenen Daten können Grundlage für die Erarbeitung von Normen für die additive Fertigung von Betonbauteilen sein und somit deren Standsicherheit gewährleisten. T2 - 63. For‍schungs‍kol‍lo‍qui‍um des Deutschen Ausschuss für Stahlbeton CY - Berlin, Germany DA - 16.10.2024 KW - Additive Fertigung KW - Beton KW - Frischbetoncharakterisierung KW - Extrusionsdruck PY - 2024 AN - OPUS4-61390 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jeyifous, Olubunmi Anthony A1 - Schönsee, Eric A1 - Strangfeld, Christoph A1 - Hüsken, Götz T1 - Correlation of continuously measured in-line process parameters and extruded geometry in 3D concrete printing experiments N2 - Additive manufacturing of concrete structures is a novel and emerging tech-nology. Free contouring in civil engineering, which allows for entirely new designs, is a significant advantage. Although several techniques and ap-proaches demonstrate these advantages, quality control during printing is highly challenging and rarely applied. Due to the continuous mixing process used in 3D concrete printing, it is impossible to exclude variations in the dry mixture or water content, and a single test sample is insufficient to represent the whole structure. A defect in one layer during printing can affect the in-tegrity of the entire structure. Therefore, continuous and real-time process monitoring is required to record and document the printing process. At the Bundesanstalt für Materialforschung und -prüfung (BAM), a test rig for 3D concrete printing was developed to monitor the properties during the printing process. This study investigates the relationship between geometric accuracy and process parameters (pressure, pump torque, print speed, layer height, water content) in extrusion-based 3D concrete printing. Using a high-precision laser scanner, the geometric measurements of printed concrete ele-ments are evaluated in real-time. The concrete elements are printed under controlled conditions with varied process parameters. Preliminary findings indicate a significant correlation between process variables and geometric ac-curacy. T2 - Fourth RILEM International Conference on Concrete and Digital Fabrication CY - Munich, Germany DA - 04.09.2024 KW - 3D concrete printing KW - Geometric accuracy KW - Process monitoring KW - Quality control PY - 2024 DO - https://doi.org/10.1007/978-3-031-70031-6_15 SP - 127 EP - 133 AN - OPUS4-61534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jeyifous, Olubunmi Anthony T1 - Correlation of continuously measured in-line process parameters and extruded geometry in 3D concrete printing experiments N2 - Additive manufacturing of concrete structures is a novel and emerging tech-nology. Free contouring in civil engineering, which allows for entirely new designs, is a significant advantage. Although several techniques and ap-proaches demonstrate these advantages, quality control during printing is highly challenging and rarely applied. Due to the continuous mixing process used in 3D concrete printing, it is impossible to exclude variations in the dry mixture or water content, and a single test sample is insufficient to represent the whole structure. A defect in one layer during printing can affect the in-tegrity of the entire structure. Therefore, continuous and real-time process monitoring is required to record and document the printing process. At the Bundesanstalt für Materialforschung und -prüfung (BAM), a test rig for 3D concrete printing was developed to monitor the properties during the printing process. This study investigates the relationship between geometric accuracy and process parameters. T2 - Fourth RILEM International Conference on Concrete and Digital Fabrication CY - Munich, Germany DA - 04.09.2024 KW - 3D concrete printing KW - Geometric accuracy KW - Process monitoring KW - Quality control PY - 2024 AN - OPUS4-61535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -