TY - CONF A1 - Wilsch, Gerd A1 - Völker, Tobias T1 - Laser-based building material sorting for the processing of construction and demolition waste for the circular economy N2 - A joint project of partners from industry and research institutions for the research and construction of an analysis system for an automated, sensor-supported sorting of construction and demolition waste will be presented. This is intended to supplement or replace the previously practiced manual sorting, which harbors many risks and dangers for the staff and only enables obvious, visually detectable differences for separation. The method of laser-induced breakdown spectroscopy is to be used in combination with hyperspectral sensors. Due to the jointly processed information (data fusion), this should lead to a significant improvement in the separation of types. In addition to the sorting of different materials (concrete, main masonry building materials, organic components, glass, etc.), impurities such as SO3-containing building materials (gypsum, aerated concrete, etc.) could also be detected and separated. The subsequent recycling and sales opportunities are examined, such as the use of recycled aggregates in concrete, the recycling of building materials containing sulphate as a gypsum substitute for the cement industry or the agglomeration of synthetic lightweight aggregates for lightweight concrete or as a substrate for green roofs. At the same time, it is investigated whether soluble components (sulfates, heavy metals, etc.) can be detected by LIBS without a wet chemical analysis and what impact the recycling materials have on the environment. The entire value chain is examined using the example of the Berlin location in order to minimize economic / technological barriers and obstacles on a cluster level and to sustainably increase the recovery and recycling rates. T2 - Materials Week 2021 CY - Online meeting DA - 07.09.2021 KW - Laser induced breakdown spectroscopy KW - Building waste KW - Circular economy KW - Material sorting PY - 2021 AN - OPUS4-53286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Küttenbaum, Stefan T1 - Zur Validierung von zerstörungsfreien Messverfahren für die probabilistische Beurteilung von Bestandsbauwerken mit gemessenen Daten T1 - Validation of non-destructive measurement procedures for reliability assessments of existing structures using measured data N2 - The aging of existing bridge structures coincides with the progressing degradation and increasing requirements on the bridge stock caused by increasing traffic densities as well as heavy traffic. The resulting demand for structural assessments of existing bridges is of substantial importance, both nationally and internationally. The information available about the considered system provides the basis for reassessments. Both the structural reliability and the validity of the computation results depend primarily on the condition, i.e. the quality and the relevance of this information. The purposeful measurement of quality-evaluated and relevant information can significantly increase the engineer’s power of judgement regarding the structural reliability. It is advisable to keep the destructive structural interventions necessary to obtain such information to a minimum. The purpose of the present thesis is the development and evaluation of a methodology for the probabilistic reassessment of existing structures using non-destructively measured data and for the validation of the suitability of non-destructive measurement procedures for the application in the context of reassessments. For this purpose, the applicability of the rules established within the Guide to the Expression of Uncertainty (GUM)-framework for evaluating the quality of the measured information to be used later in the reassessment is emphasized. The requirements on measured data-based basic variables are derived from the First Order Reliability Method (FORM), a probabilistic approximation procedure. Based on this, the metrology and the reassessment are brought together. The measurement-based basic variables are explicitly appreciated as random variables in reliability analyses. The developed methodology is evaluated by means of two prestressed concrete bridges and four basic variables. Geometrical measurement results gathered by radar and ultrasound measurements are incorporated into reassessments regarding the limit states ULS bending, ULS shear and SLS decompression. The modelling of the measurements is an essential part in order to calculate the measurement results, each consisting of a measured value and the attributed measurement uncertainty. It is shown that the incorporation of the non-destructively collected measurement results reduces the uncertainty to be covered and increases the level of approximation of the considered models. The measurement results are reliable and comparable. Extensive sensitivity analyses provide information about crucial structure parameters to be measured, since they significantly influence the structural reliability. This way, the relevance of the information is derived. Such analyses are suitable for the design and commissioning of investigations meeting the demands as well as for the purposeful refinement of initially insufficient computation models. Furthermore, the appreciation of measured data-based basic variables can increase the robustness of structural analyses. Measurement-based reliability reassessments are particularly useful if required information is missing or doubts have arisen about the available information. In the best case, the incorporation of non-destructively measured data results in the extension of estimated remaining service lives, in the enhancement of infrastructural availabilities and in the optimization of the consumption of resources. N2 - Die Alterung bestehender Brückenbauwerke fällt mit dem sich verschlechternden Zustand und zunehmenden Anforderungen an die Bausubstanz zusammen, die eine Folge von steigenden Verkehrszahlen und der Zulassung des Schwerlastverkehrs sind. Der daraus erwachsende Bedarf an Beurteilungen von bestehenden Brücken ist national und international fortwährend groß. Die Grundlage für Nachrechnungen sind die über das System verfügbaren Informationen. Sowohl die rechnerische Zuverlässigkeit eines Tragwerks als auch die Validität der Ergebnisse hängen im Wesentlichen vom Zustand, also von der Qualität und der Relevanz dieser Informationen ab. Die gezielte Messung von gütebewerteten, relevanten Informationen kann die Urteilsfähigkeit des Beurteilenden über die Zuverlässigkeit eines Tragwerks signifikant steigern. Wünschenswert ist die Erhebung derartiger Informationen ohne signifikante Eingriffe in die Bausubstanz. Das Ziel der vorliegenden Arbeit ist die Entwicklung und Erprobung einer Vorgehensweise für die probabilistische Beurteilung von bestehenden Bauwerken mit zerstörungsfrei gemessenen Daten und einer Methodik zum objektiven Nachweis der Eignung von zerstörungsfreien Messverfahren zur Anwendung im Zuge einer Nachrechnung. Herausgestellt wird die Eignung der im Guide to the Expression of Uncertainty in Measurement (GUM) publizierten Regeln zur Bewertung der Qualität der gemessenen Informationen, die später im statischen Nachweis verwendet werden sollen. Die Anforderungen an die Basisvariablen, d. h. an die Eingangsgrößen im probabilistischen Nachweis, werden aus den Vorschriften zur Zuverlässigkeitsanalyse mit dem probabilistischen Näherungsverfahren FORM, der First Order Reliability Method, abgeleitet. Darauf basiert die Entwicklung der Schnittstelle zwischen der Messtechnik und der Nachrechnung. Im Kern werden die messdatenbasierten Basisvariablen explizit als Zufallsgrößen bei der Zuverlässigkeitsanalyse berücksichtigt. Die entwickelte Vorgehensweise wird am Beispiel von zwei Spannbetonbrücken und vier Basisvariablen erprobt. In die Nachweise der Biege- und der Querkrafttragfähigkeit sowie in einen Nachweis der Dekompression fließen geometrische Messergebnisse ein, die mithilfe von Radar- und Ultraschallmessungen generiert werden. Ein wichtiger Bestandteil ist die Bildung von Modellen zur Auswertung der Messungen und zur Berechnung der Messergebnisse. Es wird gezeigt, dass die Einbeziehung der zerstörungsfrei generierten Messergebnisse die Unsicherheit in den Berechnungsmodellen reduzieren und den Grad der Annäherung der Modelle an die Realität steigern kann. Die Messergebnisse sind zuverlässig und vergleichbar. Umfassende Sensitivitätsanalysen geben Aufschluss über sinnvollerweise zu messende Bauwerksparameter, die einen maßgeblichen Einfluss auf die Tragwerkszuverlässigkeit ausüben. Auf diese Weise wird die Relevanz der Informationen ermittelt. Das Potential derartiger Analysen für die gezielte Planung und Beauftragung von Messungen sowie für die bedarfsgerechte Zuschärfung von initial unzureichenden Berechnungsmodellen erscheint groß. Die messdatenbasierten Modelle können darüber hinaus die Robustheit einer Tragwerksanalyse steigern. Die Berücksichtigung von Messergebnissen ist dann besonders nützlich, wenn zur Beurteilung erforderliche Informationen fehlen oder Zweifel an den verfügbaren Informationen aufgekommen sind. Im besten Fall resultiert daraus die Verlängerung von rechnerischen Restnutzungsdauern, die Steigerung der Verfügbarkeit der Infrastruktur, die Optimierung des Ressourcenverbrauchs und insgesamt eine realitätsnahe Bauwerksbewertung. KW - Zerstörungsfreie Prüfung im Bauwesen KW - Nachrechnung KW - Spannbetonbrücken KW - Zuverlässigkeitsanalyse KW - Messunsicherheit PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:bvb:706-7686 SN - 1431-5122 VL - 21/2 SP - I EP - 314 PB - Universität der Bundeswehr München CY - Neubiberg AN - OPUS4-53851 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lay, Vera A1 - Buske, S. A1 - Townend, J. A1 - Kellett, R. A1 - Savage, M. A1 - Schmitt, D. R. A1 - Constantinou, A. A1 - Eccles, J. D. A1 - Gorman, A. A1 - Bertram, M. A1 - Hall, K. A1 - Lawton, D. A1 - Kofman, R. T1 - 3D Active Source Seismic Imaging of the Alpine Fault Zone and the Whataroa Glacial Valley in New Zealand N2 - The Alpine Fault zone in New Zealand marks a major transpressional plate boundary that is late in its typical earthquake cycle. Understanding the subsurface structures is crucial to understand the tectonic processes taking place. A unique seismic survey including 2D lines, a 3D array, and borehole recordings, has been performed in the Whataroa Valley and provides new insights into the Alpine Fault zone down to ∼2 km depth at the location of the Deep Fault Drilling Project (DFDP)-2 drill site. Seismic images are obtained by focusing prestack depth migration approaches. Despite the challenging conditions for seismic imaging within a sediment filled glacial valley and steeply dipping valley flanks, several structures related to the valley itself as well as the tectonic fault system are imaged. A set of several reflectors dipping 40°–56° to the southeast are identified in a ∼600 m wide zone that is interpreted to be the minimum extent of the damage zone. Different approaches image one distinct reflector dipping at ∼40°, which is interpreted to be the main Alpine Fault reflector located only ∼100 m beneath the maximum drilled depth of the DFDP-2B borehole. At shallower depths (z < 0.5 km), additional reflectors are identified as fault segments with generally steeper dips up to 56°. Additionally, a glacially over-deepened trough with nearly horizontally layered sediments and a major fault (z < 0.5 km) are identified 0.5–1 km south of the DFDP-2B borehole. Thus, a complex structural environment is seismically imaged and shows the complexity of the Alpine Fault at Whataroa. KW - Imaging KW - Signal processing KW - Seismic KW - Borehole KW - DAS PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-539163 DO - https://doi.org/10.1029/2021JB023013 VL - 126 IS - 12 SP - 1 EP - 21 PB - American Geophysical Union AN - OPUS4-53916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan T1 - Zur Validierung von ZfP-Verfahren für die Nachrechnung von Brücken N2 - "Die effiziente Verwendung von Messergebnissen bei der Nachrechnung und von Ergebnissen aus zerstörungsfreien Prüfungen im Speziellen setzt voraus, dass die Relevanz der messbaren Informationen beziffert, die Qualität der gemessenen Information berechnet und die Anforderungen an die Genauigkeit der Inspektionen aus der statischen Berechnung abgeleitet werden können. Der Vergleich der Anforderungen an eine zu messende Information mit der Qualität der gemessenen Information wird in diesem Aufsatz als Validierung eines Messverfahrens aufgefasst. Es wird gezeigt, wie zerstörungsfreie Prüfverfahren für die Nachrechnung validiert werden können. Die Methodik wird anhand einer mit der Ultraschallecho- und Impulsradarmethode untersuchten Spannbetonbrücke demonstriert." KW - Bestandsbauwerke KW - Zuverlässigkeitsbewertung KW - Messunsicherheit PY - 2021 UR - https://www.dgzfp.de/Portals/24/Zeitung/Ausgaben/Zeitung176.pdf SN - 1616-069X IS - 176 SP - 41 EP - 48 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung e.V. (DGZfP), Österreichische Gesellschaft für Zerstörungsfreie Prüfung (ÖGfZP), Schweizerische Gesellschaft für Zerstörungsfreie Prüfung (SGZP) AN - OPUS4-53470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Tobias T1 - Round robin test for chloride analysis in cement pastes with LIBS N2 - In civil engineering, clear regulations and standards, such as the European standard DIN EN 206 apply to ensure that the existing infrastructure is sufficiently resistant to a wide range of exposure conditions. Despite these regulations, in practice concrete structures often show severe damage during their service life. One of these damages is pitting corrosion of the reinforcement, which can be caused by chloride ingress into the structure. Therefore, determining the distribution and depth of chloride ingress is important in predicting the service life. LIBS provides an alternative method to conventional wet chemistry in civil engineering. Despite many advantages, the use of LIBS has been severely limited due to a lack of regulations. Together with project partners from research and industry, we are currently working on a leaflet that will regulate chloride analysis in civil engineering using LIBS. This year, an international round robin test was organized to evaluate the performance of LIBS for chloride analysis in cement pastes. No specifications were given for the experimental LIBS setup and data evaluation. The preliminary results are presented. T2 - 11th Euro-Mediterranean Symposium on Laser-Induced Breakdown Spectroscopy (EMSLIBS) CY - Online meeting DA - 29.11.2021 KW - LIBS KW - Cement KW - Chloride KW - Round robin KW - Interlaboratory comparison PY - 2021 AN - OPUS4-53898 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gottlieb, C. T1 - Optimization of LIBS experiments using Design of experiment (DoE) N2 - To conduct a reliable, repeatable and accurate LIBS analysis, the optimization of the experimental setup is an important task. Hardware parameters of lasers and spectrometers used in the setup as well as additionally required components such as optics or process gas pipes must be carefully aligned and adjusted because factors like (i) focal conditions of the optics, (ii) alignment of the sample, (iii) process purge gas (types, flow rate) or (iv) measurement settings (integration time, accumulation of pulses) have a big impact on the signal quality. Therefore, in most cases the effect of different factors is evaluated empirically due to changing one factor at a time while keeping the overall configuration the same. In the end, the optimal configuration is selected based on the best parameters for each influencing factor. During optimization, a configuration of the experimental setup is aimed at, which allows e.g. the highest signal intensity or the lowest variation. In most cases, cross-correlation, interference and interaction among the various factors are not considered. For this reason, the possibilities of using Design of Experiment (DoE) to optimize a LIBS experiment will be shown and advantages of (i) reduction of testing plans using a feature space, (ii) identifying and considering cross-correlations and interactions, (iii) evaluating individual impacts on the measurement (e.g. contour and surface plots) as well as (iv) multivariate models for prediction of impacts will be presented. T2 - 11th Euro-Mediterranean Symposium on Laser-Induced Breakdown Spectroscopy (EMSLIBS) CY - Online meeting DA - 29.11.2021 KW - LIBS KW - Chlorine KW - DoE PY - 2021 AN - OPUS4-53899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Aßmann, Norman A1 - Bühling, Benjamin T1 - Impact-echo dataset "Radarplatte" N2 - This dataset contains raw data resulting from Impact-Echo measurements at the reference conrete block "Radarplatte", located at BAM (German Federal Institute for Materials Research and Testing). This specimen has been described in detail by Niederleithinger et al. (2021), who applied muon tomography, ultrasonic echo measurements, radar and X-ray laminography to visualize its internal structure. The Impact-Echo method is based on the excitation of the zero-group-velocity frequency of the first symmetric Lamb mode of a plate-like structure, in order to assess its thickness. Numerous publication elaborate on Impact-Echo theory, examples are (Gibson and Popovics 2005, Schubert and Köhler 2008 , Abraham and Popovics 2010). The measurements have been conducted using a setup that contains only commercially available components. The setup consists of an Olson CTG-2 concrete thickness gauge (Olsen Instruments, USA) for actuation and sensing and an 8-bit NI USB-5132 digital storage oscilloscope (National Instruments, USA) combined with the Echolyst software (Schweizerischer Verein für technische Inspektionen (SVTI), Switzerland) for data acquisition. Measurements were conducted using a grid of 23x23 points with a spacing of 50 mm. At each point 8192 samples were recorded at a sampling rate of 1 MS/s. The dataset contains the (X,Y) location in mm of the individual measurement points as well as the raw measurement data at those points. The data is provided in the formats *.mir/*.mhdr (Echolyst), *.npy (Python) and *.mat (Matlab) and *.csv to ease the import in various post-processing tools. KW - Nondestructive testing KW - Impact-echo KW - S1-ZGV mode KW - Concrete PY - 2021 DO - https://doi.org/10.7910/DVN/UNOH2U PB - Harvard College CY - Cambridge, MA, USA AN - OPUS4-53886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schweitzer, T. A1 - Hörmann, M. A1 - Bühling, Benjamin A1 - Bobusch, B. T1 - Switching Action of a Bistable Fluidic Amplifier for Ultrasonic Testing N2 - Air-coupled ultrasonic testing is widely used in the industry for the non-destructive testing of compound materials. It provides a fast and efficient way to inspect large concrete civil infrastructures for damage that might lead to catastrophic failure. Due to the large penetration depths required for concrete structures, the use of traditional piezoelectric transducer requires high power electric systems. In this study, a novel fluidic transducer based on a bistable fluidic amplifier is investigated. Previous experiments have shown that the switching action of the device produces a high-power broadband ultrasonic signal. This study will provide further insight into the switching behaviour of the fluidic switch. Therefore, parametric CFD simulations based on compressible supersonic RANS simulations were performed, varying the inlet pressure and velocity profiles for the control flow. Switching times are analyzed with different methods, and it was found that These are mostly independent of the slope of the velocity profile at the control port. Furthermore, it was found that an inversely proportional relationship exists between flow velocity in the throat and the switching time. The results agree with the theoretical background established by experimental studies that can be found in the literature. KW - Ultrasound KW - Non-destructive testing KW - Fluidic devices KW - Computational fluid dynamics KW - Concrete KW - Bistable fluidic amplifier PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-525115 DO - https://doi.org/10.3390/fluids6050171 SN - 2311-5521 VL - 6 IS - 5 SP - 171 PB - MDPI CY - Basel, Switzerland AN - OPUS4-52511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lay, Vera T1 - 3D seismic imaging of the Alpine Fault and the glacial valley at Whataroa, New Zealand N2 - The Alpine Fault at the West Coast of the South Island (New Zealand) is a major plate boundary that is expected to rupture in the next 50 years, likely as a magnitude 8 earthquake. The Deep Fault Drilling Project (DFDP) aimed to deliver insight into the geological structure of this fault zone and its evolution by drilling and sampling the Alpine Fault at depth. Here we present results from a seismic survey around the DFDP-2 drill site in the Whataroa Valley where the drillhole almost reached the fault plane. This unique 3D seismic survey includes several 2D lines and a 3D array at the surface as well as borehole recordings. Within the borehole, the unique option to compare two measurement systems is used: conventional three-component borehole geophones and a fibre optic cable (heterodyne Distributed Vibration Sensing system (hDVS)). Both systems show coherent signals but only the hDVS system allowed a recording along the complete length of the borehole. Despite the challenging conditions for seismic imaging within a glacial valley filled with sediments and steeply dipping valley flanks, several structures related to the valley itself as well as the tectonic fault system are imaged. The pre-processing of the seismic data also includes wavefield separation for the zero-offset borehole data. Seismic images are obtained by prestack depth migration approaches. Within the glacial valley, particularly steep valley flanks are imaged directly and correlate well with results from the P-wave velocity model obtained by first arrival travel-time tomography. Additionally, a glacially over-deepened trough with nearly horizontally layered sediments is identified about 0.5 km south of the DFDP-2B borehole. With regard to the expected Alpine fault zone, a set of several reflectors dipping 40-56° to the southeast are identified in a ~600 m wide zone between depths of 0.2 and 1.2 km that is interpreted to be the minimum extent of the damage zone. Different approaches image one distinct reflector dipping at 40°, which is interpreted to be the main Alpine Fault reflector. This reflector is only ~100 m ahead from the lower end of the borehole. At shallower depths (z<0.5 km), additional reflectors are identified as fault segments and generally have steeper dips up to 56°. About 1 km south of the drill site, a major fault is identified at a depth of 0.1-0.5 km that might be caused by the regional tectonics interacting with local valley structures. A good correlation is observed among the separate seismic data sets and with geological results such as the borehole stratigraphy and the expected surface trace of the fault. In conclusion, several structural details of the fault zone and its environment are seismically imaged and show the complexity of the Alpine Fault at the Whataroa Valley. Thus, a detailed seismic characterization clarifies the subsurface structures, which is crucial to understand the transpressive fault’s tectonic processes. T2 - EGU 2021 General Assembly CY - Online meeting DA - 19.04.2021 KW - Imaging KW - Signal processing KW - Seismic KW - Borehole KW - DAS PY - 2021 AN - OPUS4-52614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - NDE4.0 in civil engineering - obstacles and opportunities N2 - Civil engineering industry is one of the most important industry sectors in the world-wide economy. It contributes significantly to the gross economic product and general employment. Even more important, it provides many of the basic needs of the society (e. g. housing, infrastructure, protection from natural hazards). The concept of “Industry 4.0” or “Smart Production” has not yet made significant progress in the civil engineering industry. The design, build and operate processes are still widely dominated by the exchange of printed documents and drawings. Most objects (buildings and other constructions) are unique, and a large part of the production still requires a large amount of manual labor. As-built documentation and quality assurance are often neglected. Civil engineering is among the industries sectors with the lowest level of digitalization and the lowest gain in productivity. However, this is going to change. In the past decade, several drivers have challenged the ways clients, contractors, and authorities currently operate. These drivers include but are not limited to an increasing demand for serialization and automatization, the mandatory introduction of “Building Information Modeling” (BIM) in public procurement, the availability of construction equipment with sensors and digital interfaces or emerging automated construction technologies such as 3D-printing. NDE (referred to as NDT-CE in this sector), after a rapid technological development in the last two decades, plays an increasing role in quality assurance, condition assessment and monitoring of structures. However, with very few exceptions, applications are mostly non-standardized and performed only at selected sites. To change this, the NDT-CE community including manufacturers, service providers, clients and the scientific community must work consistently on open data formats, interfaces to BIM, standardization and validated ways for a quantitative use of the results in the assessment of constructions. T2 - International Virtual Conference on NDE 4.0 CY - Online Meeting DA - 14.04.2021 KW - NDT KW - BIM KW - SHM KW - NDE 4.0 PY - 2021 AN - OPUS4-52623 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Validierung von ZfP-Verfahren für die Nachrechnung von Brücken N2 - Vortrag über die Bewertung der Zuverlässigkeit von bestehenden Brücken mit gezielt am Bauwerk erhobenen ZfP-Ergebnissen im Rahmen der Verleihung des DGZfP-Nachwuchspreises 2021 auf der Jahrestagung der DGZfP. T2 - DGZfP-Jahrestagung 2021 CY - Online meeting DA - 10.05.2021 KW - Zuverlässigkeit KW - Messunsicherheit KW - Reliability assessment KW - Existing structures PY - 2021 AN - OPUS4-52630 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -