TY - CONF A1 - Liao, Chun-Man A1 - Petryna, Y. T1 - Damage Assessment of Civil Structures Using Wave Propagation Analysis and Transmissibility Functions N2 - A common damage detection method in civil engineering is to monitor dynamic characteristics such as natural frequencies and modal shapes, which are directly related to the structural stiffness. However, the discrepancy in measured natural frequencies may result from environmental changes, the soil-structure interaction or effects caused by earthquakes. This makes it difficult to decide whether the local change in structural properties is caused by damage or other factors. To address this challenge and thus improve the current damage detection method, the wave propagation analysis method and the transmissibility relationship were considered. In our study, the wave propagation field in structures was reconstructed by applying the Normalized-Input-Output-Minimization (NIOM) method to vibration recordings. Wave velocities and transmissibility functions were considered as reference values for the damage indicators. This paper demonstrates the evaluation of local property changes in two examples of large-scale structures: a 14-story RC building and a 64 m long pedestrian bridge. The proposed damage indicators show a clear correspondence to structural changes. T2 - EVACES2021 9th International Conference on Experimental Vibration Analysis for Civil Engineering Structures CY - Online meeting DA - 14.09.2021 KW - Damage detection KW - Damage indices KW - Normalized-Input-Output-Minimization KW - Transmissibility function KW - Wave propagation PY - 2022 SN - 978-3-030-93235-0 SN - 978-3-030-93236-7 DO - https://doi.org/10.1007/978-3-030-93236-7_2 SP - 3 EP - 13 PB - Springer CY - Cham AN - OPUS4-55565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lay, Vera T1 - Geophysikalische Methoden für die Zerstörungsfreie Prüfung im Bauwesen N2 - Im Rahmen des Seminars "Angewandte Forschungsthemen (SAFT)" am Institut für Geowissenschaften der Christian-Albrechts-Universität zu Kiel werden verschiedene geophysikalische Methoden vorgestellt, die bei der zerstörungsfreien Prüfung im Bauwesen zum Einsatz kommen. Neben einem Überblick der Arbeiten an der BAM im Allgemeinen und dem Fachbereich im Besonderen geht es vor allem um den Einsatz von Ultraschallmethoden. Drei wesentliche Schwerpunkte werden dabei beleuchtet: 1) (Geophysikalische) Antworten auf Herausforderungen bei Ultraschall-Anwendungen 2) Material research and multi-sensory monitoring for concrete sealing structures in rock salt unterground repositories (Projekt SealWasteSafe) und 3) Untersuchung von Spritzbeton-Probekörpern unter Tage mit Ultraschall zur Qualitätssicherung von Verschlussbauwerken. Insgesamt werden diverse Möglichkeiten für die Geophysik für Forschung und Studierende im Bereich der zerstörungsfreien Prüfung im Bauwesen aufgezeigt. T2 - Seminar Angewandte Forschungsthemen CY - Kiel, Germany DA - 14.06.2023 KW - SealWasteSafe KW - Ultraschall KW - Verschlussbauwerke KW - Abbildungsverfahren PY - 2023 AN - OPUS4-57828 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Tobias T1 - Laserbasierte Baustoffsortierung zur Aufbereitung von Bau und Abbruchabfällen für die Kreislaufwirtschaft (LIBS ConSort) N2 - Geschlossene Materialkreisläufe und sortenreine Materialfraktionen sind erforderlich, um hohe Verwertungs und Recyclingquoten in der Bauindustrie zu erreichen Beim Recycling von Bau und Abbruchabfällen wurden bisher bevorzugt einfache, aber bewährte Techniken eingesetzt, um große Mengen Bauschutt in kurzer Zeit zu verarbeiten Dies steht im Gegensatz zu den immer komplexer werdenden Verbundwerkstoffen in der Mineralbaustoffindustrie Die aktuell oft praktizierte händische Klaubung bürgt viele Risiken und Gefahren für das ausführende Personal und basiert lediglich auf offensichtlichen, visuell erkennbaren Unterschieden zur Trennung Eine automatisierte, sensorgestützte Sortierung dieser Baustoffe könnte diese Praxis ergänzen oder ersetzen, um die Verarbeitungsgeschwindigkeit, die Recyclingraten, die Sortierqualität und die vorherrschenden Gesundheitsbedingungen zu verbessern. T2 - ReMin Statuskonferenz 2023 CY - Clausthal Zellerfeld, Germany DA - 20.06.2023 KW - LIBS PY - 2023 AN - OPUS4-57752 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Tobias T1 - LIBS ConSort Laserbasierte Baustoffsortierung zur Aufbereitung von Bau und Abbruchabfällen für die Kreislaufwirtschaft N2 - Geschlossene Materialkreisläufe und sortenreine Materialfraktionen sind erforderlich, um hohe Verwertungs und Recyclingquoten in der Bauindustrie zu erreichen Beim Recycling von Bau und Abbruchabfällen wurden bisher bevorzugt einfache, aber bewährte Techniken eingesetzt, um große Mengen Bauschutt in kurzer Zeit zu verarbeiten Dies steht im Gegensatz zu den immer komplexer werdenden Verbundwerkstoffen in der Mineralbaustoffindustrie Die aktuell oft praktizierte händische Klaubung bürgt viele Risiken und Gefahren für das ausführende Personal und basiert lediglich auf offensichtlichen, visuell erkennbaren Unterschieden zur Trennung Eine automatisierte, sensorgestützte Sortierung dieser Baustoffe könnte diese Praxis ergänzen oder ersetzen, um die Verarbeitungsgeschwindigkeit, die Recyclingraten, die Sortierqualität und die vorherrschenden Gesundheitsbedingungen zu verbessern. T2 - ReMin Statuskonferenz 2023 CY - Clausthal Zellerfeld, Germany DA - 20.06.2023 KW - LIBS PY - 2023 AN - OPUS4-57753 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Tobias T1 - Laser Induced Breakdown Spectroscopy A Tool for Imaging the Chemical Composition of Concrete N2 - One of the most common causes of damage is the ingress of harmful ions into the concrete, which can lead to deterioration processes and affect structural performance. Therefore, the increasingly aging infrastructure is regularly inspected to assess durability. Regular chemical analysis can be useful to determine the extent and evolution of ion ingress and to intervene in a timely manner. This could prove more economical than extensive repairs for major damage, particularly for critical infrastructure. In addition to already established elemental analysis techniques in civil engineering such as potentiometric titration or X-ray fluorescence analysis, laser-induced breakdown spectroscopy (LIBS) can provide further important complementary information and benefits. The possibilities of LIBS are demonstrated using the example of a drill core taken from a parking garage. T2 - 6th International Conference on Concrete Repair, Rehabilitation and Retrofitting CY - Cape Town, South Africa DA - 03.10.2022 KW - LIBS KW - Concrete KW - Cement KW - Chlorine PY - 2022 AN - OPUS4-56061 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Völker, Tobias A1 - Klewe, Tim A1 - Kruschwitz, Sabine T1 - Laser Induced Breakdown Spectroscopy – A Tool for Imaging the Chemical Composition of Concrete N2 - One of the most common causes of damage is the ingress of harmful ions into the concrete, which can lead to deterioration processes and affect structural performance. Therefore, the increasingly aging infrastructure is regularly inspected to assess durability. Regular chemical analysis can be useful to determine the extent and evolution of ion ingress and to intervene in a timely manner. This could prove more economical than extensive repairs for major damage, particularly for critical infrastructure. In addition to already established elemental analysis techniques in civil engineering such as potentiometric titration or X-ray fluorescence analysis, laser-induced breakdown spectroscopy (LIBS) can provide further important complementary information and benefits. The possibilities of LIBS are demonstrated using the example of a drill core taken from a parking garage. T2 - 6th International Conference on Concrete Repair, Rehabilitation and Retrofitting CY - Kapstadt, South Africa DA - 03.10.2022 KW - LIBS KW - Concrete KW - Chlorine PY - 2022 UR - https://iccrrr2022.org/downloads SP - 126 EP - 127 AN - OPUS4-56062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scherr, J. F. A1 - Kollofrath, J. A1 - Popovics, J. S. A1 - Bühling, Benjamin A1 - Grosse, C. U. T1 - Detection of Delaminations in Concrete Plates Using a Laser Ablation Impact Echo Technique N2 - This study investigates the non-destructive detection of delaminations in concrete plates using non-contact laser ablation, instead of the conventional hammer excitation, as part of the impact echo method. We performed tests on five concrete specimens of different sizes, two of which contained artificial delaminations. A range of steel ball hammers was used as reference impulse sources, the responses of which were compared with wave excitation generated by a 7 ns pulsed 1064 nm Nd:YAG laser with 150 mJ pulse energy. Signals were recorded by surface-mounted accelerometers and two contactless methods: microphones and a laser Doppler vibrometer. The laser generates frequencies across a broad range of frequencies (0 to 150 kHz) but with much less energy than the hammers' narrower frequency spectra; the laser pulse energy transferred into the specimen is 0.07 mJ, corresponding to about 0.5 ‰ of the impulse source energy. Because of this, the thick intact plates' characteristic thickness stretch resonance frequency can be reliably detected by the hammer excitations but not when using laser excitation. However, the laser can excite low-frequency flexural vibration modes over a shallow delamination at 3 cm depth. The low-frequency flexural vibration results are verified by numerical natural frequency analysis. KW - Concrete testing KW - Defect detection KW - Lamb waves KW - Impact echo KW - Non-destructive testing KW - Vibration PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567932 DO - https://doi.org/10.1007/s10921-022-00921-x SN - 0195-9298 VL - 42 IS - 1 SP - 1 EP - 14 PB - Springer AN - OPUS4-56793 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd T1 - Laser induced breakdown spectroscopy to investigate the chemical composition of concrete N2 - Laser-induced breakdown spectroscopy (LIBS) is a spectroscopic method for detecting the chemical composition of optically accessible surfaces. In principle, the measurement of all elements of the periodic table is possible. System calibrations allow the quantification of element concentrations. In combination with scanner systems, the two-dimensional element distribution can be determined. Even rough surfaces can be measured by online adjustment of the laser focus. To detect element ingress into the concrete, typically cores are taken, cut in half, and LIBS measurements are performed on the cross-section. The high spatial resolution as well as the simultaneous multi-element analysis enables a separate evaluation of the binder-matrix and aggregates. Therefore, the element concentrations can be determined directly related to the cement paste. LIBS measurements are applicable in the laboratory, on-site and also over a distance of several meters. Common applications include the investigation of material deterioration due to the ingress of harmful ions and their interaction in porous building materials. LIBS is able to provide precise input parameters for simulation and modelling of the remaining lifetime of a structure. Besides the identification of materials, also their composition can be determined on hardened concrete, such as the type of cement or type of aggregate. This also involves the identification of environmentally hazardous elements contained in concrete. Another possible application is the detection of the composition of material flows during dismantling. Non-contact NDT for “difficult to assess” structures as an example application through safety glass or in combination with robotics and automation are also possible. This work presents the state of the art concerning LIBS investigations on concrete by showing exemplary laboratory and on-site applications. T2 - NDE NucCon 2023 CY - Espoo, Finland DA - 25.01.2023 KW - LIBS KW - Concrete PY - 2023 AN - OPUS4-57323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Völker, Tobias A1 - Klewe, Tim A1 - Kruschwitz, Sabine T1 - Laser-induced breakdown spectroscopy to investigate the chemical composition of concrete N2 - Laser-induced breakdown spectroscopy (LIBS) is a spectroscopic method for the analysis of the chemical composition of sample materials. Generally, the measurement of all elements of the periodic table is possible. In particular, light elements such as H, Li, Be, S, C, O, N and halogens can be measured. Calibration with matrix-matching standards allows the quantification of element concentrations. In combination with scanner systems, the two-dimensional element distribution can be determined. Even rough surfaces can be measured by online adjustment of the laser focus. LIBS can also be used on-site with mobile systems. Hand-held systems are available for point measurements. Common applications include the investigation of material deterioration due to the ingress of harmful ions and their interaction in porous building materials. Due to the high spatial resolution of LIBS and the consideration of the heterogeneity of concrete, the determination of precise input parameters for simulation and modelling of the remaining lifetime of a structure is possible. In addition to the identification of materials, it is also possible to assess the composition for example of hardened concrete, which involves the cement or aggregate type used. Other important fields of application are the detection of environmentally hazardous elements or the material classification for sorting heterogeneous material waste streams during dismantling. Non-contact NDT for “difficult to assess” structures as an example application through safety glass or in combination with robotics and automation are also possible. In this work, an overview of LIBS investigations on concrete is given based on exemplary laboratory and on-site applications. T2 - NDE NucCon 2023 CY - Espoo, Finland DA - 25.01.2023 KW - LIBS KW - Concrete KW - Chemical analysis PY - 2023 UR - https://www.aalto.fi/en/nde-nuccon-2023 SP - 351 EP - 359 AN - OPUS4-57303 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Völker, Tobias A1 - Gornushkin, Igor B. T1 - Extension of the Boltzmann plot method for multiplet emission lines N2 - The Boltzmann plot method is widely used to determine the temperature of laser induced plasma. It involves the use of individual lines that are not easy to find in complex spectra and/or in the spectral range available. If the number of such lines is not enough to build a reliable Boltzmann plot, overlapping lines are often used, which are separated by software. However, line separation is a rather imprecise procedure, which, in addition, requires significant computational costs. This study proposes an extension of the Boltzmann plot method that allows a specific group of unresolved lines to be included in a Boltzmann plot without the need to separate them. This group of lines are multiplets, lines of the same element with similar upper and lower transition states. The multiplet lines along with the individual lines are included in the algorithm, which also includes a correction for self-absorption and is used to determine the plasma temperature. The algorithm is tested on synthetic spectra which are consistent with the model of a homogeneous isothermal plasma in local thermodynamic equilibrium and is shown to be superior to the standard Boltzmann plot method both in more accurate determination of the plasma temperature and in a significant reduction in the computational time. The advantages and disadvantages of the method are discussed in the context of its applications in laser induced breakdown spectroscopy. KW - LIBS KW - Spectroscopy KW - Boltzmann plot KW - Multiplet KW - Spectral overlap PY - 2023 DO - https://doi.org/10.1016/j.jqsrt.2023.108741 SN - 1879-1352 VL - 310 SP - 1 EP - 5 PB - Elsevier AN - OPUS4-58058 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas T1 - Ultrasonic monitoring of large-scale structures – input to engineering assessment N2 - Ultrasonic coda wave interferometry can detect small changes in scattering materials like concrete. We embedded ultrasonic transducers in the Gänstorbrücke Ulm, a monitored road bridge in Germany, to test the methodology. Since fall 2020, we've been monitoring parts of the bridge and comparing the results to commercial monitoring systems. We calculate signal and volumetric velocity changes using coda waves, and long-term measurements show that the influence of temperature on strains and ultrasound velocity changes can be monitored. Velocity change maps indicate that different parts of the bridge react differently to environmental temperature changes, revealing local material property differences. A load experiment with trucks allows calibration to improve detectability of possibly damaging events. Our work focuses on measurement reliability, potential use of and distinction from temperature effects, combination with complementary sensing systems, and converting measured values to information for damage and life cycle assessment. T2 - IALCCE 2023 CY - Milano, Italy DA - 02.07.2023 KW - Ultrasonic KW - Monitoring KW - Bridges KW - NDT KW - Coda PY - 2023 AN - OPUS4-58046 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas A1 - Sanchez Trujillo, Camila Andrea A1 - Niederleitinger, Ernst T1 - Ultrasonic monitoring of large-scale structures – input to engineering assessment N2 - Ultrasonic coda wave interferometry can detect small changes in scattering materials like concrete. We embedded ultrasonic transducers in the Gänstorbrücke Ulm, a monitored road bridge in Germany, to test the methodology. Since fall 2020, we've been monitoring parts of the bridge and comparing the results to commercial monitoring systems. We calculate signal and volumetric velocity changes using coda waves, and long-term measurements show that the influence of temperature on strains and ultrasound velocity changes can be monitored. Velocity change maps indicate that different parts of the bridge react differently to environmental temperature changes, revealing local material property differences. A load experiment with trucks allows calibration to improve detectability of possibly damaging events. Our work focuses on measurement reliability, potential use of and distinction from temperature effects, combination with complementary sensing systems, and converting measured values to information for damage and life cycle assessment. T2 - IALCCE 2023 CY - Milano, Italy DA - 02.07.2023 KW - Ultrasonic KW - Monitoring KW - Bridge KW - NDT KW - coda PY - 2023 SP - 1 EP - 8 PB - IALCCE CY - Milan AN - OPUS4-58047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Christian T1 - Eignungsprüfungen geophysikalischer Sensoren zur Rissdetektion an Demonstrationsbauwerken N2 - Bei der Betonage von Abdichtbauwerken können Temperaturen bis 110 °C und hohe Drücke bis 5 MPa erreicht werden. Mittels Technikumsversuchen wurde nachgewiesen, dass Mikroakustik- und Ultraschallsensoren zum Einbau in Demonstrationsbauwerke geeignet sind. Die Untersuchungen wurden bei der BAM (Bundesanstalt für Materialforschung und -prüfung) in Berlin durchgeführt. Es ist vorgesehen, die Sensoren in Morsleben am Demonstrationsbauwerk im Anhydrit einzusetzen. T2 - 84. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Jena, Germany DA - 10.03.2024 KW - Ultraschall KW - Eignungsprüfung KW - Risse KW - Abdichtbauwerk KW - Anhydrit PY - 2024 AN - OPUS4-59772 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Reliability reassessment of bridges with geometrical NDT results N2 - This presentation summarizes recent developments within the scope of the national pre-standardization project “ZfPStatik”, which aims to prepare a guideline about NDT-supported structural analyses. The focus is on the purposeful and explicit utilization of geometrical tendon and reinforcement bar positions measured on-site in reliability analysis — shown by means of a prestressed concrete bridge as case study. T2 - 13th German Japanese Bridge Symposium CY - Osaka, Japan DA - 28.08.2023 KW - Existing structures KW - Probabilistic methods KW - Data-supported assessment PY - 2023 AN - OPUS4-58268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Kainz, C. A1 - Braml, T. T1 - Reliability assessment of existing concrete bridges with geometrical NDT results - Case studies N2 - The results of and the validity in reliability assessment of existing bridges essentially depend on the information available about the considered system. Information about the actual condition as well as structural and material characteristics can be observed on-site to refine the computation models used in assessment. Non-destructive testing (NDT) methods for concrete structures are capable of reconstructing missing, questioned, or inconsistent as-built plans. This contribution summarizes recent developments within the scope of the national pre-standardization project “ZfPStatik”, which aims to prepare a guideline about NDT-supported structural analyses. The focus is on the purposeful and explicit utilization of geometrical tendon and reinforcement bar positions (measured on-site using the ultrasound echo and ground penetrating radar (GPR) techniques) in probabilistic reliability analyses — shown by means of real case studies. The well-established first order reliability method is applied to different concrete bridges, which are typical for the German road bridge stock, to demonstrate the utility of incorporating quality-evaluated NDT-results in terms of changes in structural reliability. T2 - 13th German-Japanese Bridge Symposium CY - Osaka, Japan DA - 28.08.2023 KW - Non-destructive testing KW - Prestressed concrete KW - Data-informed reliability analysis PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582727 SP - 29 EP - 40 PB - Osaka Metropolitan University CY - Osaka AN - OPUS4-58272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epple, Niklas T1 - Coda Measurements for monitoring infrastructure durability N2 - Presentation about the advancements in the DFG Research unit CoDA, with focus on Coda Wave Monitoring of Infrastructure. With some case studies, possibilities and challenges are discussed on the way towards infrastructural monitoring with CWI. T2 - PhD-Seminar Department 8.2 CY - Berlin, Germany DA - 07.09.2023 KW - CWI KW - Embedded Sensors KW - Ultrasound KW - Bridge Monitoring PY - 2023 AN - OPUS4-58196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Relevant, abgesichert, vergleichbar – ZfP-Ergebnisse bei der Zuverlässigkeitsbewertung von Bauwerken N2 - Die Nachrechnung, d. h. die Zuverlässigkeitsbewertung von bestehenden Brücken, ist aufgrund der alternden Infrastruktur und sich verändernden Anforderungen an die Bauwerke eine fortwährend große Herausforderung in Wissenschaft, Praxis und Standardisierung. Ein wesentlicher Vorteil bei der Nachrechnung besteht gegenüber dem Neubauentwurf in der Möglichkeit, Informationen über den tatsächlichen Zustand der Bauwerke zu erheben – im Idealfall ohne wesentliche destruktive Eingriffe in die Bausubstanz. Deren Verwendung bei der Zuverlässigkeitsanalyse dient der Zuschärfung von Berechnungsmodellen und ermöglicht realitätsnähere Bauwerksbeurteilungen. Die Einbeziehung von Messdaten bei der Zuverlässigkeitsbewertung setzt jedoch voraus, dass die Qualität der gemessenen Informationen bekannt und deren Vergleichbarkeit sichergestellt ist. Darüber hinaus sollte die Relevanz der messbaren Informationen beziffert werden, um wirtschaftliche Inspektionen am Bauwerk gezielt durchführen zu können. In diesem Beitrag wird am Beispiel von Ultraschall- und Radarmessungen an einer Spannbetonbrücke gezeigt, wie ZfP-Ergebnisse bei der Zuverlässigkeitsbewertung von Bestandsbauwerken mit probabilistischen Methoden genutzt werden können. Betrachtet werden innere geometrische Abmessungen wie die Lage der Bewehrung oder von Spanngliedern. Die Relevanz der messbaren Informationen wird anhand von Sensitivitätsanalysen beziffert. Messunsicherheitsbetrachtungen dienen der Bezifferung der Qualität der gemessenen Informationen und der Gewährleistung deren Vergleichbarkeit. Abschließend werden die möglichen Auswirkungen der Berücksichtigung von ZfP-Ergebnissen auf die Bauwerkszuverlässigkeit in einem Nachweis einer Spannbetonbrücke gemäß Eurocode demonstriert. T2 - Fachtagung Bauwerksdiagnose 2024 CY - Berlin, Germany DA - 29.02.2024 KW - ZfPStatik KW - Nachrechnung KW - Zuverlässigkeitsbewertung KW - Bestandsbauwerke KW - Betonbrücke PY - 2024 AN - OPUS4-59585 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ballio, F. A1 - Chatzi, E. A1 - Cigada, A. A1 - Darò, P. A1 - Elfgren, L. A1 - Gentile, C. A1 - Górski, M. A1 - Küttenbaum, Stefan A1 - Limongelli, M. P. A1 - Mancini, G. A1 - Oliveira, S. A1 - Rasol, M. A1 - Schmidt, F. A1 - Shan, J. A1 - Sousa, H. A1 - Torrent, R. A1 - Ueda, T. A1 - Verstrynge, E. T1 - Chapter 6: Case studies N2 - This chapter contains a selection of case studies that show the implementation of the methods and tools that have been described in the previous chaprters of fib Bulletin 109 on actual large-scale structures. KW - Structural engineering KW - Structural Health Monitoring KW - Non-destructive testing KW - Static and dynamic reassessment KW - Existing structures PY - 2023 SN - 978-2-88394-172-4 DO - https://doi.org/10.35789/fib.BULL.0109.Ch06 SN - 1562-3610 VL - fib Bulletin 109 SP - 104 EP - 126 PB - Fédération internationale du béton (fib) CY - Lausanne AN - OPUS4-59341 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Guideline on NDT-supported reliability assessment of existing structures N2 - The presentation summarizes the idea and the methodology of the ZfPStatik project and gives insight into three case studies, showing how non-destructive testing results can be utilized beneficially in the recalculation of existing prestressed concrete and reinforced concrete bridges. T2 - 2nd Conference of the European Association on Quality Control of Bridges and Structures – EUROSTRUCT2023 CY - Vienna, Austria DA - 26.09.2023 KW - Reliability KW - Assessment KW - Existing structures KW - Non-destructive testing PY - 2023 AN - OPUS4-58485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Völker, Tobias A1 - Gornushkin, Igor B. T1 - Investigation of a method for the correction of self-absorption by Planck function in laser induced breakdown spectroscopy N2 - The electron density and temperature of a laser-induced plasma can be determined from the width and intensity of the spectral lines, provided that the corresponding optical transitions are optically thin. However, the lines in laser induced plasma are often self-absorbed. One of the methods of correction of this effect is based on the use of the Planck function and an iterative numerical calculation of the plasma temperature. In this study, the method is further explored and its inherent errors and limitations are evaluated. For this, synthetic spectra are used that fully correspond to the assumed conditions of a homogeneous isothermal plasma at local thermodynamic equilibrium. Based on the error analysis, the advantages and disadvantages of the method are discussed in comparison with other methods of self-absorption correction. KW - LIBS KW - Self-absorption KW - Planck function PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572677 DO - https://doi.org/10.1039/D2JA00352J SN - 0267-9477 SP - 1 EP - 6 PB - Royal Society of Chemistry (RSC) AN - OPUS4-57267 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - ZfPStatik - Verbesserte Beurteilung von Bestandsbauwerken N2 - Vorgestellt werden - die Projektziele - das Konsortium - die allgemeine Vorgehensweise - und aktuelle Fortschritte im WIPANO-Projekt "ZfPStatik" (Stand: Februar 2023). T2 - 3. vierteljährliche Versammlung des Projektkonsortiums CY - Neubiberg, Germany DA - 07.02.2023 KW - Zerstörungsfreie Prüfung KW - Nachrechnung KW - Zuverlässigkeitsbewertung KW - Bestandsbauwerke PY - 2023 AN - OPUS4-57239 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hicke, Konstantin A1 - Liao, Chun-Man A1 - Chruscicki, Sebastian A1 - Breithaupt, Mathias T1 - Vibration Monitoring of Large-Scale Bridge Model using Distributed Acoustic Sensing N2 - Results of DAS measurements along a large-scale concrete bridge model are presented. The improvement of measurable dynamic strain range is demonstrated. Vibration modes obtained by DAS correspond well to those determined from broadband seismometer measurements. T2 - 27th International Conference on Optical Fiber Sensors (OFS-27) CY - Alexandria, VA, USA DA - 29.08.2022 KW - Distributed acoustic sensing KW - Vibration modes KW - Bridge monitoring KW - WS-COTDR KW - Fiber-optic vibration monitoring PY - 2022 SP - 1 EP - 4 PB - Optica CY - Washington D.C., USA AN - OPUS4-56082 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lay, Vera T1 - Innovations in cemented waste handling and pre-disposal storage (WP7 project PREDIS) N2 - During the webinar "Dismantling and waste management: a playground for innovation" the innovative aspects of the PREDIS work package "innovations in cemented waste handling and pre-disposal storage" are presented. The webinar is jointly organised by Women in Nuclear Decommissioning (WINDI) and Women in Nuclear Innovation (WINI). The shown innovations include quality assurance (mainly NDE) and monitoring technologies with associated sensor systems, digital twin technology, and appropriate data handling including a decision framework. An overview of the on-going research in the field of pre-disposal waste management in the project Predis (WP7) is summarised. T2 - Webinar "Dismantling and waste management: a great playground for innovation" CY - Online meeting DA - 13.10.2022 KW - Predis KW - Waste management KW - Concrete PY - 2022 AN - OPUS4-56926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd T1 - Application of LIBS in civil engineering – status, trends and challenges N2 - The main application of LIBS in civil engineering is the detection of harmful ions in concrete, which can penetrate the component through the porous concrete structure. The advantages of LIBS over standard methods are the possibility of multi-element analysis, measurement speed, spatially resolved measurements, and minimal sample preparation. The spatially resolved measurements of LIBS allow the assessment of the heterogeneity of the concrete by measuring separately the chemical composition of the aggregates and the binder matrix. The latter is particularly relevant because the determined elemental distribution can be directly related to the binder matrix. This is not possible with standard methods, since the material is homogenized to powder during sample preparation stage and the determined concentration is thus related to the total mass. In addition to the use of LIBS for the specific analysis of individual harmful ions, LIBS can also be used to estimate the concrete composition and thus determine, for example, the type of cement used. Corresponding information are relevant for the estimation of the remaining service life and for the preparation of a maintenance concept. In recent years, LIBS has been increasingly used in civil engineering. Currently, however, it is primarily used in research institutions and only occasionally in building materials laboratories. Special commercial devices have also been developed, which greatly simplify the application due to the high degree of automation. Mobile LIBS systems allow on-site application. A central point, which limits the use of LIBS in the commercial sector, is the lack of norms and standards. Therefore, within the framework of a project funded by the German government, work has been carried out on the preparation of a leaflet on quantitative chlorine determination in concrete, which will be published this year. In interlaboratory comparisons the robustness and accuracy for the practical application was demonstrated. LIBS also has great potential in the recycling of construction waste in conjunction with hyperspectral sensors. This issue is currently being addressed in a national project. During the presentation, the state of the art of LIBS in civil engineering will be presented, next steps will be discussed, and future challenges will be outlined. T2 - XII international conference on laser induced breakdown spectroscopy (LIBS 2022) CY - Bari, Italy DA - 04.09.2022 KW - LIBS KW - Concrete KW - Chlorine KW - Civil engineering PY - 2022 AN - OPUS4-56535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd T1 - Condition assessment of concrete infrastructure with LIBS N2 - Due to the ageing of the infrastructure facilities, a reliable assessment of the condition of concrete structures is of great interest to plan timely and appropriate measures. In concrete structures, pittingcorrosion of the reinforcement is the predominant deterioration mechanism affecting serviceability and eventually structural performance. Determination of quantitative chloride ingress is not only necessary to obtain valuable information on the current condition of a structure, but the data obtained can also be used to predict future developments and the associated risks. An overview of the progress and the possibilities of the application of laser-induced breakdown spectroscopy for concrete analysis in daily civil engineering practice is given. High-resolution 2D measurements of drill cores to determine the penetration of harmful species into concrete is presented. Furthermore, the application of a mobile LIBS system in a parking garage is shown. The system consists of a diode-pumped low-energy laser (3 mJ, 1.5 ns, 100 Hz) and a compact NIR spectrometer. A scanner allows two-dimensional element mapping. Progress towards the establishment of LIBS in a leaflet for the analysis of chlorine ingress into concrete in civil engineering is presented. T2 - Euro-Mediterranean Symposium on Laser-Induced Breakdown Spectroscopy 2021 CY - Gijón, Spain DA - 29.11.2021 KW - LIBS KW - Concrete KW - Chlorine KW - Civil engineering PY - 2021 AN - OPUS4-56536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd T1 - Laser Induced Breakdown Spectroscopy – A Tool for the Chemical Investigation of Concrete N2 - LIBS is a complementary method to XRF and can detect all elements without the need for vacuum conditions. Automated systems are already commercially available capable of scanning surfaces with a resolution of up to 0.1 mm within a few minutes. In addition to possible applications in R&D, LIBS is also used for practical applications in building materials laboratories and even on-site. In view of ageing infrastructure facilities, a reliable assessment of the condition of concrete structures is of increasing interest. For concrete structures, the ingress of potential harmful ions is affecting the serviceability and eventually structural performance. Pitting corrosion induced by penetrating chlorides is the dominant deterioration mechanism. Condition assessment based on frequently performed chloride profiling can be useful to identify the extent and evolution of chloride ingress. This could prove to be more economical than extensive repairs, especially for important infrastructure facilities. Currently the most common procedure for determining the chloride content is wet chemical analysis with standard resolution of 10 mm. The heterogeneity is not considered. LIBS is an economical alternative for determining the chloride content at depth intervals of 1 mm or less. It provides 2D distributions of multiple elements and can locate spots with higher concentrations. The results are directly correlated to the mass of binder and can also be performed on-site with a mobile LIBS-System. The application of a LIBS-system is presented. Calibration is required for quantitative analysis. Concrete cores were drilled, sliced and analyzed to determine the 2D-distribution of harmful elements. By comparing the chloride ingress and the carbonation, the interaction of both processes can be visualized in a measurement that takes less than 10 minutes for a 50 mm x 100 mm drill core. A leaflet on the use of LIBS for the chloride ingress assessment has been completed. T2 - NDT-CE 2022 - The International Symposium on Nendestructive Testing in Civil Engineering CY - Zurich, Switzerland DA - 16.08.2022 KW - Chlorides KW - Corrosion KW - Imaging KW - Service life KW - Damage assessment KW - LIBS PY - 2022 AN - OPUS4-56540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Völker, Tobias A1 - Wilsch, Gerd A1 - Gornushkin, Igor B. A1 - Kratochvilo, L. A1 - Pořízka, P. A1 - Kaiser, J. A1 - Millar, S. A1 - et al., T1 - Interlaboratory comparison for quantitative chlorine analysis in cement pastes with laser induced breakdown spectroscopy N2 - Concrete structures experience severe damage during service, for example due to pitting corrosion of rebars caused by the ingress of chlorine (Cl) into the porous concrete structure. The ingress can be monitored using laser-induced breakdown spectroscopy (LIBS), a recently introduced civil engineering technique used to detect Cl in concrete structures in addition to conventional wet chemistry methods. The key advantages of LIBS are high spatial resolution, which is important when analyzing heterogeneous concrete samples, as well as the almost complete absence of sample preparation. To assess LIBS as a reliable analytical method, its accuracy and robustness must be carefully tested. This paper presents the results of an interlaboratory comparison on the analysis of Cl in cement paste samples conducted by 12 laboratories in 10 countries. Two sets of samples were prepared with Cl content ranging from 0.06 to 1.95 wt% in the training set and 0.23–1.51 wt% in the test set, with additional variations in the type of cement and Cl source (salt type). The overall result shows that LIBS is suitable for the quantification of the studied samples: the average relative error was generally below 15%. The results demonstrate the true status quo of the LIBS method for this type of analysis, given that the laboratories were not instructed on how to perform the analysis or how to process the data. KW - LIBS KW - Interlaboratory comparison KW - Round robin test KW - Cement KW - Chlorine PY - 2023 DO - https://doi.org/10.1016/j.sab.2023.106632 SN - 0584-8547 VL - 202 SP - 1 EP - 8 PB - Elsevier B.V. AN - OPUS4-57102 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Küttenbaum, Stefan A1 - Kainz, C. A1 - Braml, T. ED - Matos, J.C. T1 - Non-destructively Measurable Quantities Relevant to Reliability Assessment of Existing Concrete Bridges – Case Studies N2 - In reliability assessment of existing bridges, collected information about the structure can be utilized to modify partial safety factors and to refine characteristic values individually. In this way, uncertainties covered in initial calculation models and arising from assumptions can be reduced as well as biases identified and corrected. This allows for more realistic assessments and more appropriate decisions on actions to be taken. However, the on-site observation of information is generally associated with certain costs. For this reason, an efficient data-supported reassessment requires that only the individually relevant testing tasks are solved. Additional sensitivity analyses can further be used to specify the requirements on certain inspections, such as the testing result quality to be achieved, in order to avoid too imprecise or too expensive measurements on-site. In this contribution, the methodology for the demand-actuated definition of measurement objectives is demonstrated using the example of non-destructive concrete testing methods and findings from reassessments of two prestressed concrete bridges. Each case study includes the semi-probabilistic identification of structural weak points in ultimate and serviceability limit states, a comparison with respective probabilistic sensitivity analyses, and the subsequent derivation of parameters that are a) measurable and b) highly relevant in the individual reliability analyses. KW - Reliability KW - Assessment KW - Existing structures KW - Non-destructive testing PY - 2024 SN - 978-3-031-60270-2 DO - https://doi.org/10.1007/978-3-031-60271-9_18 VL - 494 SP - 209 EP - 219 PB - Springer CY - Cham AN - OPUS4-60613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Kainz, C. A1 - Braml, T. A1 - Keuser, M. A1 - Soukup, A. A1 - Küttenbaum, Stefan ED - Matos, J.C. T1 - Reassessment of Existing Concrete Bridges with Full Probabilistic Methods – Case Studies and Discussion of Relevant Input Parameters N2 - This article presents two case studies for a full-probabilistic assessment of existing concrete bridges combined with the use of the finite element method for the evaluation of the internal forces. Since the structures already exist, additional information about material parameters and loading conditions can be collected. With a sensitivity analysis, the contribution of each parameter to the total uncertainty is examined and the relevance of their actual value and variation is shown. The first case study is a single-span reinforced concrete frame bridge on the German highway A92 constructed in the year 1985. With a span of around 5 m, but a width of 27 m and a skewness of 70 gon, the bridge is modelled as a three-dimensional finite element model. The second case study is a two-span reinforced concrete frame bridge from 1986 with span lengths of about 7,50 m each. The superstructure is a 45 cm thick slab and the base plate has a thickness of 80 cm. The assessment is performed based on the semi-probabilistic safety concept according to the codes first and secondly with a full-probabilistic calculation. In this article the selection of parameters for the relevant input data are presented and discussed. The results of the sensitivity analysis are used for the setup of measurements to acquire important data for the modelling in the critical limit states. KW - Reliability KW - Assessment KW - Existing structures PY - 2024 SN - 978-3-031-60271-9 DO - https://doi.org/10.1007/978-3-031-60271-9_41 VL - 494 SP - 440 EP - 451 PB - Springer CY - Cham AN - OPUS4-60614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Özlü, C. A1 - Küttenbaum, Stefan A1 - Kainz, C. A1 - Braml, T. A1 - Taffe, A. T1 - Probabilistischer Nachweis einer Spannbetonbrücke – Teil 1 N2 - AbstractDer Erhalt der bestehenden Verkehrsinfrastruktur ist eine große Herausforderung, da die Bauwerke fortwährend altern, die Verkehrsbeanspruchung zunehmend steigt und deren umfassender Ersatz mit Blick auf begrenzte Budgets und Ressourcen nicht möglich ist. An Bestandsbauten können tatsächliche Materialkennwerte, Geometrien oder Einwirkungen objektspezifisch erfasst werden. Die Nachrechnung von Bestandsbrücken erfolgt in Deutschland gemäß Nachrechnungsrichtlinie nach Stufen 1 und 2 mit dem semiprobabilistischen Teilsicherheitskonzept. Nur im Ausnahmefall wird eine messbasierte Bewertung oder eine wissenschaftliche Betrachtung gemäß Stufen 3 und 4 durchgeführt. Die Einbeziehung zusätzlicher Informationen aus der Zustandserfassung bietet jedoch viele Vorteile für eine realitätsnahe Bewertung. In probabilistischen Berechnungsmethoden können solche Kenntnisse direkt in der Berechnung berücksichtigt werden. Ziel dieses zweiteiligen Beitrags ist die Vorstellung der Potenziale und Vorteile bei der direkten Berücksichtigung der Ergebnisse von zerstörungsfreien Prüfverfahren bei der Zustandsbewertung von Brückenbauwerken. Das Konzept wird an einer Spannbetonbrücke vorgestellt. Der erste Teil befasst sich mit den Möglichkeiten zur Überführung der Eingangswerte der üblichen semiprobabilistischen Berechnung in stochastische Modelle. Ausgehend von der semiprobabilistischen Nachrechnung nach derzeitigem Regelwerk wird die probabilistische Modellierung aller relevanten Basisvariablen für die Grenzzustände der Tragfähigkeit Biegung, Querkraft und Torsion ausgeführt. KW - Zuverlässigkeitsanalyse KW - Nachrechnung KW - Bestandsbauwerk PY - 2024 DO - https://doi.org/10.1002/best.202400018 VL - 119 IS - 7 SP - 509 EP - 523 PB - Wiley AN - OPUS4-60615 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Özlü, C. A1 - Küttenbaum, Stefan A1 - Kainz, C. A1 - Braml, T. A1 - Taffe, A. T1 - Probabilistischer Nachweis einer Spannbetonbrücke – Teil 2 N2 - AbstractIm zweiten Teil dieses Beitrags werden die Grenzzustandsfunktionen für die Nachweise im Grenzzustand der Tragfähigkeit für Biegung mit Normalkraft, Querkraft mit Querkraftbewehrung und Torsion vorgestellt. Die Eingangsgrößen der mechanischen Widerstandsmodelle werden durch zahlreiche Abbildungen illustriert. Auf Grundlage der probabilistischen Modelle aus dem ersten Teil dieses Aufsatzes und der mechanischen Modelle aus diesem zweiten Teil werden die probabilistischen Nachweise geführt. Die Ergebnisse aus der Zuverlässigkeitsanalyse werden mit den semiprobabilistischen Berechnungsergebnissen verglichen. Mittels Parameterstudien wird gezeigt, welche Eingangsgrößen im Standsicherheitsnachweis die größten Einflüsse auf die Bauwerkszuverlässigkeit haben. Die Messung dieser Parameter ist entsprechend besonders nützlich. Auf dieser Basis wird abschließend gezeigt, welche Chancen sich aus der Durchführung von zerstörungsfreien Bauwerksprüfungen für die Nachrechnung ergeben. KW - Zuverlässigkeitsanalyse KW - Nachrechnung KW - Bestandsbauwerk PY - 2024 DO - https://doi.org/10.1002/best.202400020 SN - 1437-1006 VL - 119 SP - 1 EP - 14 PB - Ernst & Sohn CY - Berlin AN - OPUS4-60616 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Imaging of results in NDT-CE: Strength and limitations in the use of Radar vs. Ultrasonic Echo N2 - Presentation on behalf of the co-author specified in BAM-Publica. Study on capabilities of volume methods (GPR, Ultrasonic Echo) regarding lateral and depth localisation of reinforcement and tendons in concrete components. Varied boundary conditions: spacing and diameter of both the near surface rebars of the mesh, and the reflectors of interest, as well as component thickness and concrete cover. Please find corresponding references on slide 2. T2 - 6th International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR2022) CY - Cape Town, South Africa DA - 03.10.2022 KW - Reinforcement KW - Tendon duct KW - Concrete KW - NDT KW - Localisation PY - 2022 AN - OPUS4-55987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grohmann, Maria T1 - Anwendung der Reverse-Time Migration auf Ultraschall-Echo-Daten in der zerstörungsfreien Prüfung von Betonbauteilen N2 - Das Ultraschall-Echo-Verfahren ist eine klassische zerstörungsfreie Prüftechnik zur Geometriebestimmung sowie Schadensanalyse von Betonkonstruktionen. Um die Abbildung der Ultraschalldaten von komplexen Betonstrukturen zu verbessern, haben wir die Reverse-Time Migration (RTM) aus der Seismik auf die zerstörungsfreie Prüfung im Bauwesen übertragen. In einer Vorstudie haben wir einen 2D akustischen RTM Code verwendet und an realen Ultraschalldaten, die an einer Betonfundamentplatte aufgenommen wurden, getestet. Im Vergleich mit dem herkömmlichen Rekonstruktionsalgorithmus für Ultraschalldaten, der Synthetic Aperture Focusing Technique (SAFT), zeigten die akustischen RTM-Ergebnisse eine deutliche Verbesserung in der Abbildung der inneren Struktur der Betonfundamentplatte. Vertikale Reflektoren konnten rekonstruiert werden, was mit dem herkömmlichen Abbildungsverfahren nicht möglich war. RTM ist, im Gegensatz zu SAFT, eine wellengleichungsbasierte Migrationsmethode und beruht auf der numerischen Lösung der vollständigen Wellengleichung. Die Vorteile sind, dass der Algorithmus sämtliche Informationen des Wellenfeldes verwendet und daher verschiedene Welleneffekte wie z.B. Multipathing berücksichtigt werden können. Die RTM bietet damit die Möglichkeit auch stark geneigte Reflektoren sowie Streukörper mit komplexen Geometrien darzustellen. Ein Nachteil ist jedoch die lange Rechenzeit und der hohe Bedarf an Speicherkapazität. Ein RTM-Algorithmus, der die elastische Wellengleichung anstatt der akustischen verwendet (wie in unserer Vorstudie angewandt), hat das Potenzial, die Abbildungsergebnisse noch weiter zu optimieren. Das liegt daran, dass unsere Ultraschallmessdaten durch Anregung elastischer Wellen generiert werden. In einem ersten Schritt haben wir zwei elastische 2D-RTM-Algorithmen an synthetischen Ultraschalldaten getestet. Diese wurden mit einem Betonmodell, bestehend aus mehreren Stufen und kreisförmigen Lufteinschlüssen, erzeugt. In einem zweiten Schritt wurden reale Ultraschalldaten mit Scherwellenprüfköpfen an einer Betonstufenplatte mit integrierten Hüllrohren aufgenommen. Die Auswertung der realen Daten mit unserem elastischen RTM-Code war ebenfalls erfolgreich. Wir konnten die Abbildungsqualität der Stufen und Hüllrohre im Vergleich zur akustischen RTM und SAFT verbessern. T2 - Tagung Deutsche Geophysikalische Gesellschaft DGG CY - Munich, Germany DA - 07.03.2022 KW - Ultraschall-Echo-Verfahren KW - Reverse Time Migration KW - Synthetic Aperture Focusing Technique PY - 2022 AN - OPUS4-56112 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grohmann, Maria T1 - Application of Elastic Reverse Time Migration to Ultrasonic Echo Data in Civil Engineering N2 - The ultrasonic echo technique is widely used in non-destructive testing for investigation and damage analysis of concrete constructions. Important applications include thickness measurements, geometry determination, the localization and characterization of built-in components as well as the detection of quality issues (cracks, honeycombing, low concrete strength). To improve ultrasonic data imaging of complicated structures in concrete, we transferred a seismic migration technique, the Reverse Time Migration (RTM), to non-destructive testing in civil engineering. In a preliminary study, we tested a 2D acoustic RTM algorithm on measured ultrasonic echo data acquired at a concrete foundation slab. Compared to the conventional used synthetic aperture focusing technique algorithms (SAFT) for ultrasonic data reconstruction, our acoustic RTM results showed a significant improvement in imaging the interior structure of the concrete slab. Vertical reflectors were reconstructed which was not possible by traditional imaging. In contrast to SAFT, RTM is a wavefield-continuation method in time and uses the full wave equation. RTM is, thus, able to include multiple reflections and to handle multi-pathing as well as many other complex situations. As a drawback RTM requires extensive computing power and memory capacity. Nevertheless, due to progresses in parallel processing and other computational technologies RTM has become appealing for the application in the field of non-destructive testing. An RTM algorithm, which uses the full elastic wave equation instead of the full acoustic one (as applied in our preliminary work) has the potential to optimize the imaging results even further. This is due to the fact, that our ultrasonic measurement data are generated by exciting elastic waves. Thus, in a first step, two 2D elastic RTM algorithms were tested on synthetic ultrasonic echo data generated with a concrete model consisting of several steps and circular shaped air inclusions. In addition, two imaging conditions were evaluated to reduce migration artifacts. Our synthetic elastic RTM results showed an enhancement in imaging the features inside the test model compared to acoustic RTM and SAFT. In a second step, we acquired ultrasonic measurement data at a concrete test specimen consisting of three steps and four air filled tendon ducts. The evaluation of the real data with our elastic RTM code was also successful and the reconstruction of the geometries of the steps and tendon ducts could be improved. With our study we have shown that elastic RTM is a step forward for ultrasonic testing in civil engineering. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Ultrasonic Echo Technique KW - Reverse Time Migration KW - Synthetic Aperture Focusing Technique PY - 2022 AN - OPUS4-56113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - PREDIS The pre-disposal management of radioactive waste N2 - This presentation summarizes the opbjectives and the progress of the EURATOM project PREDIS (pre-disposal management of radioactive waste) and its workpackage 7 in particular. Focus is on the development of wireless sensors for monitoring radioactive waste packages, measuring radiation, temperature, pressure and humidity. T2 - DigiDecom 2022 CY - Halden, Norway DA - 18.10.2022 KW - Radioactive waste KW - Monitoring KW - Wireless KW - RFID PY - 2022 AN - OPUS4-56321 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Imani, A. A1 - Niederleithinger, Ernst T1 - Nondestructive Evaluation of Bridges without Structural Plans for Load Rating Purposes N2 - According to the NBI database, more than 21,000 in-service U.S. bridges lack sufficient structural documentation necessary for analytical load rating. Among these are a significant proportion of older prestressed concrete bridges. Given the lack of documentation on the reinforcing layout, such structures cannot be load rated analytically and are often subject to engineering judgement as the basis for rating. Otherwise, the typical approach for load rating such bridges is to conduct costly proof load testing and destructive probing together with making conservative assumptions. Therefore, any improvement to current practices will benefit DOTs and taxpayers alike. Accurately reconstructed 3D images of the girders to reflect the internal reinforcement could mitigate the need for costly, if not impractical, destructive testing and proof load testing, and help reduce dependency on conservative assumptions. This study examines a comprehensive NDE approach using ultrasonic tomography and GPR to aid in gathering structural information for load rating purposes. Different types of AASHTO and hollow core girders were tested. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Ultrasound KW - Radar KW - Bridges KW - Load rating PY - 2022 AN - OPUS4-56356 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Völker, Tobias A1 - Gottlieb, Cassian A1 - Kapteina, Gesa A1 - Wilsch, Gerd A1 - Millar, Steven A1 - Reichling, Kenji T1 - Neues DGZfP-Merkblatt B14: Quantifizierung von Chlorid in Beton mittels LIBS N2 - Bei der Erhaltung von Stahlbetonbauwerken ist der Chloridgehalt im Beton ein wichtiger Parameter zur Festlegung geeigneter Instandsetzungsmaßnahmen. Die bisher etablierten Verfahren basieren auf der nasschemischen Analyse einer Probe, Bohrmehl oder aufgemahlener Segmente eines Bohrkerns. Das Verfahren liefert einen Chloridgehalt je Tiefensegment, was mit einer starken Homogenisierung der Probe einhergeht, wodurch detaillierte Informationen zu Chloridunterschieden im Millimeterbereich verloren gehen. Eine alternative Methode ist die laserinduzierte Plasmaspektroskopie (LIBS), die nicht nur die quantitative ortsaufgelöste Bestimmung des Chloridgehalts im Bezug zur Zementmasse ermöglicht, sondern auch simultan detaillierte Informationen über die Verteilung vieler anderer chemischer Elemente liefert. Die räumliche Auflösung liegt in der Regel im Bereich von einigen Millimetern, kann aber bei Bedarf auf 0,1 mm oder weniger erhöht werden. Das neue Merkblatt B14 „Quantifizierung von Chlorid in Beton mit der laserinduzierten Plasmaspektroskopie (LIBS)“ der Deutschen Gesellschaft für Zerstörungsfreie Prüfungen (DGZfP) regelt und vereinheitlicht erstmals die zuverlässige und reproduzierbare Ermittlung des Chloridgehalts mit LIBS. In diesem Beitrag wird das Merkblatt vorgestellt und anhand praktischer Anwendungsbeispiele das Potenzial von LIBS für Fragestellungen in der Betonerhaltung verdeutlicht. KW - LIBS KW - Chlor KW - Chlorid KW - Beton KW - Bauwerksdiagnostik PY - 2024 DO - https://doi.org/10.1002/best.202400014 SP - 1 EP - 7 AN - OPUS4-60005 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Johann, Sergej A1 - Stürenberg, Jan A1 - Tandon, Aditya T1 - Robotergestütztes Bauwerksmonitoring basierend auf eingebetteter Sensorik N2 - In den letzten Jahrzehnten hat sich das Bauwerksmonitoring (engl. „Structural Health Monitoring“, SHM) zu einer nützlichen Ergänzung routinemäßiger Inspektionen entwickelt. SHM ermöglicht die frühzeitige Erkennung von Schäden an Bauwerken und dadurch die frühe, und somit kostengünstige, Durchführung von Reparatur- und Wartungsarbeiten. Mit dem Aufkommen drahtloser Technologien und Fortschritten in der Informations- und Kommunikationstechnologie werden Bauwerke zunehmend mit drahtlosen Sensorknoten ausgestattet, um für SHM relevante Bauwerksdaten zu erfassen, zu analysieren und zu übertragen. Eine vielversprechende Methode für SHM ist die direkte Einbettung von Sensoren in den Beton. In diesem Beitrag wird ein Sensorsystem zur Einbettung in Beton vorgestellt, das in der Lage ist, die im Beton aufgenommenen Bauwerksdaten auszuwerten. Die Sensoren werden bei Bedarf von vierbeinigen Robotern mittels Radio Frequency Identification (RFID) ausgelesen und mit Energie versorgt, was einen automatisierten und effizienten Prozess ermöglicht. Der prototypische Prozess zur automatischen Erfassung von Bauwerksdaten mit eingebetteter Sensorik und vierbeinigen Robotern wird durch Tests in einer Büroumgebung validiert. Die Ergebnisse der Tests bestätigen die automatische und effiziente Erfassung von Bauwerksdaten, die eine frühzeitige Erkennung von Bauwerksschäden, auch von nicht sichtbaren Schäden, ermöglicht, und eine folgerichtige Weiterentwicklung des modernen Bauwerksmonitorings repräsentiert. T2 - 35. Forum Bauinformatik CY - Hamburg, Germany DA - 18.09.2024 KW - Radio Frequency Identification (RFID) KW - Bauwerksmonitoring (SHM) KW - Eingebettete Sensorik KW - Vierbeinige Roboter KW - Autonome Navigation PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-621890 DO - https://doi.org/10.15480/882.13502 SP - 139 EP - 146 AN - OPUS4-62189 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stührenberg, Jan T1 - Robotergestütztes Bauwerksmonitoring basierend auf eingebetteter Sensorik N2 - In den letzten Jahrzehnten hat sich das Bauwerksmonitoring (engl. „Structural Health Monitoring“, SHM) zu einer nützlichen Ergänzung routinemäßiger Inspektionen entwickelt. SHM ermöglicht die frühzeitige Erkennung von Schäden an Bauwerken und dadurch die frühe, und somit kostengünstige, Durchführung von Reparatur- und Wartungsarbeiten. Mit dem Aufkommen drahtloser Technologien und Fortschritten in der Informations- und Kommunikationstechnologie werden Bauwerke zunehmend mit drahtlosen Sensorknoten ausgestattet, um für SHM relevante Bauwerksdaten zu erfassen, zu analysieren und zu übertragen. Eine vielversprechende Methode für SHM ist die direkte Einbettung von Sensoren in den Beton. In diesem Beitrag wird ein Sensorsystem zur Einbettung in Beton vorgestellt, das in der Lage ist, die im Beton aufgenommenen Bauwerksdaten auszuwerten. Die Sensoren werden bei Bedarf von vierbeinigen Robotern mittels Radio Frequency Identification (RFID) ausgelesen und mit Energie versorgt, was einen automatisierten und effizienten Prozess ermöglicht. Der prototypische Prozess zur automatischen Erfassung von Bauwerksdaten mit eingebetteter Sensorik und vierbeinigen Robotern wird durch Tests in einer Büroumgebung validiert. Die Ergebnisse der Tests bestätigen die automatische und effiziente Erfassung von Bauwerksdaten, die eine frühzeitige Erkennung von Bauwerksschäden, auch von nicht sichtbaren Schäden, ermöglicht, und eine folgerichtige Weiterentwicklung des modernen Bauwerksmonitorings repräsentiert. T2 - 35. Forum Bauinformatik CY - Hamburg, Germany DA - 18.09.2024 KW - Radio Frequency Identification (RFID) KW - Bauwerksmonitoring (SHM) KW - Eingebettete Sensorik KW - Vierbeinige Roboter KW - Autonome Navigation PY - 2024 AN - OPUS4-62190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Duddi, M. A1 - Kocherla, Amarteja A1 - Subramaniam, K. V. L. T1 - Evaluation of boundary and material influences on the dynamic electromechanical impedance response of the embedded PZT sensor in concrete N2 - The article explores the material and structural size effects on the electrical impedance response of the embedded PZT sensors which are used as an sensors/actuator in the smart sensing concrete. An embedded sensor for use in concrete monitoring is developed using Lead Zirconate Titanate (PZT). The electrical impedance (EI) response of the sensor placed inside concrete cubes of varying sizes are recorded for an applied electrical input of varying frequency. The dynamic response of the embedded PZT sensor to the applied electrical input is determined by the mechanical impedance offered by the surrounding medium. In specimens of finite size, the mechanical impedance to the motion of the PZT is influenced by the combination of dynamic material resistance and structural stiffness (size of the structure). The current study examined the effects of material resistance and size of structure on the EI response of the PZT sensor embedded in concrete medium. The influence of the size of the medium from small-sized specimens is seen in the form of secondary peaks, identified as structural peaks, on the resonance spectrum of the embedded PZT sensor. The structural peaks on the EI response are very dominant in the concrete cube of small sizes. Magnitude and intensity of these structural peaks attenuate with an increase in the size of the concrete cube. Also, the EI response from the smaller-sized specimens registered a significant leftward shift in the spectrum. The observations from the numerical simulations also showed the mechanical impedance of the surrounding concrete medium to the motion of the PZT also increases and converges at 150 mm. At sizes below 150 mm, the structural effects that are influenced by the specimen boundary must be separated to access the material properties of the concrete medium from the measured EI response of an embedded PZT sensor. At sizes, larger than 150 mm, the dynamic motion of the PZT patch and the measured EI response of the PZT patch depend only on the dynamic material properties of the concrete medium around the sensor. The zone of influence and its importance in standardization of PZT sensor for SHM of concrete structures is discussed. KW - PZT KW - Concrete sensor KW - Embedded KW - Electrical impedance KW - Mechanical impedance KW - Zone of influence PY - 2023 DO - https://doi.org/10.1016/j.sna.2023.114575 SN - 0924-4247 SN - 1873-3069 VL - 361 SP - 1 EP - 12 PB - Elsevier CY - Amsterdam AN - OPUS4-61791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Narayanan, A. A1 - Duddi, M. A1 - Kocherla, Amarteja A1 - Subramaniam, K. V. L. T1 - Continuous monitoring of the early-age strength development of cement paste using embeddable piezoelectric-based ultrasonic transducers N2 - A piezoelectric-based ultrasonic transducer that can be embedded at the time of casting is developed for the purpose of continuously monitoring the early-age strength development of cement paste. The transducers that have been developed are equipped with various levels of protection in order to enhance their resilience in an alkaline environment and mitigate the risk of short-circuits. The transducers are operated in actuator-receiver mode. The obtained ultrasonic signal is analyzed in frequency domain. The initial and final setting time estimated from calorimetry measurements demonstrated a strong agreement with the proposed frequency domain approach. The observed behavior of concrete in wave transmission measurements exhibits similarities to that of an electronic filter. Initially, concrete behaves similar to a low-pass filter, but as time elapses, it transitions into a high-pass filter. T2 - 9th Civil Structural Health Monitoring Workshop (CSHM-9) CY - Kuwait City, Kuwait DA - 12.02.2024 KW - Hydration KW - Embedded sensor KW - Early-age KW - Cementitious KW - PZT KW - Ultrasonic PY - 2024 SN - 978-3-031-62252-6 SN - 978-3-031-62255-7 SN - 978-3-031-62253-3 DO - https://doi.org/10.1007/978-3-031-62253-3_4 SN - 2366-2557 N1 - Serientitel: Lecture notes in civil engineering – Series title: Lecture notes in civil engineering VL - 516 SP - 44 EP - 51 PB - Springer Nature Switzerland CY - Cham AN - OPUS4-62593 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duddi, M. A1 - Kocherla, Amarteja A1 - Subramaniam, K. V. L. T1 - Real-time monitoring of concrete properties using an embedded smart piezoelectric sensor with active and passive sensing abilities N2 - Concrete undergoes physical and chemical changes from the time of casting. These changes in early stage of hydration of concrete, highly influence the final properties and overall performance of concrete structures. Comprehensive health monitoring sensors can help to improve the quality and performance of concrete structures by providing detailed and accurate real-time information about the properties and condition of concrete at different stages of its life cycle. In this study, an embedded smart PZT (Lead Zirconate and Titanium) sensor is developed and its potential for comprehensive health monitoring of concrete structures is explored. To protect the PZT sensor from short-circuiting and alkaline environment, a robust and sensitive protection scheme is developed. The developed embedded smart PZT sensor was placed in the concrete during casting to infer the in-situ properties of concrete through active and passive sensing techniques. Through active sensing techniques Electrical Impedance (EI) and wave propagation (WP), the hydration and damage are monitored, respectively; through passive sensing techniques vibration, and acoustic emission (AE), the development of Young’s modulus and cracking in concrete are monitored. The methodology to infer the changes inworkability, complete set behavior, property development, and crack opening in concrete structures is developed. The reproducibility of all these techniques using the developed embedded smart PZT sensor is established. Since the developed sensor is capable of both active and passive sensing, it allows for a more comprehensive and flexible approach to health monitoring. This contributes to increased data accuracy, reliability, and a more holistic understanding of the concrete structure’s condition. T2 - 1st Interdisciplinary Symposium on Smart & Sustainable Infrastructure (ISSSI 2023) CY - Vancouver, BC, Canada DA - 04.09.2023 KW - Embedded smart PZT sensor KW - Electrical impedance (EI) KW - Wave propagation (WP) KW - Acoustic emission (AE) KW - Vibration monitoring KW - Hydration KW - Damage PY - 2024 SN - 978-3-031-53388-4 SN - 978-3-031-53389-1 SN - 978-3-031-53391-4 DO - https://doi.org/10.1007/978-3-031-53389-1_96 SN - 2211-0844 N1 - Serientitel: RILEM bookseries – Series title: RILEM bookseries VL - 48 SP - 1089 EP - 1100 PB - Springer Nature CY - Cham AN - OPUS4-62681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Machbarkeitsstudie zur Zustandserfassung von Spannbetonschwellen mit dem Ultraschallverfahren N2 - Das niederfrequente Ultraschallverfahren zur zerstörungsfreien Zustandserfassung von Stahlbetonkomponenten findet im Bauwesen umfangreiche Anwendung. Multistatische Arrays sind am Markt verfügbar und ausgelegt für die Prüfung großflächiger Betonstrukturen. In einer Machbarkeitsstudie wird überprüft, ob eine Zustandserfassung an schlanken Spannbetonschwellen möglich ist. B70-Schwellen und B90-Weichenschwellen wurden hierfür im Labor, im Schienennetz und während der Wiederaufbereitung mit dem Ultraschallverfahren untersucht. Fokus ist die Detektion von Sickenrisse, Kopfrissen und Treibrissen im Bereich des Schwellenkopfes. Die rekonstruierten Ultraschalldaten zeigen für intakt-klassifizierte Schwellen ein reproduzierbares Rückwandecho und weitere Reflexionen an den Schwellenaußenkanten. Die Ausprägung der Amplitude variiert je nach Degradation durch Belastung und Verwitterung. Defekt-klassifizierte Schwellen mit z. B. Kopfrissen oder unterseitigen Abplatzungen unterscheiden sich im Signalbild deutlich durch oberflächennahe Reflexionen bzw. verschobene Rückwandechos. Basierend auf den untersuchten Schwellen zeigt die Machbarkeitsstudie, dass eine zerstörungsfreie Zustandserfassung mit Hilfe des Ultraschallverfahrens grundsätzlich möglich ist. T2 - 13. Fachtagung ZfP im Eisenbahnwesen CY - Erfurt, Germany DA - 12.03.2024 KW - Zerstörungsfreie Prüfung KW - Spannbetonschwelle KW - Ultraschallverfahren KW - Beton KW - Zustandsermittlung PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-596536 AN - OPUS4-59653 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Klewe, Tim T1 - Comparison of the Calcium Carbide Method and Darr Drying to Quantify the Amount of Chemically Bound Water in Early Age Concrete N2 - Hydration is the exothermic reaction between anhydrous cement and water, which forms the solid cement matrix of concrete. Being able to evaluate the hydration is of high interest for the use of both conventional and more climate-friendly building materials. The experimental monitoring is based on temperature or moisture measurements. The first needs adiabatic conditions, which can only be achieved in laboratory. The latter is often measured comparing the weight of the material sample before and after oven drying, which is time-consuming. This study investigates the moisture content of two cement-based and two calcium sulphate based mixtures for the first 90 days by using the calcium carbide method and oven drying at 40 °C and 105 °C (Darr method). Thereby, the amount of chemically bound water is determined to derive the degree of hydration. The calcium carbide measurements highly coincide with oven drying at 40 °C. The calcium carbide method is therefore evaluated as a suitable alternative to the time-consuming Darr drying. The prompt results are seen as a remarkable advantage and can be obtained easily in laboratory as well as in the field. KW - Concrete KW - Hydration KW - Material moisture KW - Calcium carbide method KW - Bound water KW - Darr method KW - Oven drying KW - Chemisorption KW - Physisorption PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-564519 DO - https://doi.org/10.3390/ma15238422 VL - 15 IS - 23 SP - 1 EP - 16 PB - MDPI AN - OPUS4-56451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (< 1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Earth masonry KW - Material moisture KW - Molecular diffusion KW - Chemisoprtion KW - Knudsen effect KW - Physisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-571391 SP - 1 EP - 8 PB - RILEM CY - Champs-sur-Marne AN - OPUS4-57139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Johann, Sergej A1 - Strangfeld, Christoph A1 - Zimmek, David A1 - Bartholmai, Matthias T1 - Smart electronic helper for long-term monitoring of bridges and building structures N2 - Increasing traffic volume on the one hand and ageing infrastructure on the other hand have created many new challenges for maintenance and structural health monitoring of roads and bridges. In the past, many bridges and road structures have been neglected, often resulting in traffic congestion, road closure, and increased repair costs. This research is concerned with the development of a system to improve the challenge of maintenance and early detection of damage, particularly moisture penetration and corrosion of steel reinforced concrete components. The objective is to develop a method that will also work after 30 years and longer. Many new IoT solutions are equipped with internal energy storage elements (accumulators or batteries) which are inappropriate here, since most relevant signs of concrete degradation occur after decades, where the functioning of such elements are more than questionable. The presented technology approach uses radio-frequency identification (RFID) and enables connectivity to sensors. It offers the advantage of an passive, completely independent energy supply without any energy storage components. Since the system should be permanently embedded in concrete, it is crucial to develop a long-term stable device which is adapted to the environmental influences of the structure, e.g., long-term resistance in very alkaline environment of pH 13. In numerous experiments, the robustness of the system was tested and evaluated. Various tests with encapsulations to protect the electronics were performed, and for long-term validation different concrete specimens were instrumented with RFID-sensor-systems. Their operating time is now around two years and investigations for signs of fatigue and damage to the encapsulation and the electronics are ongoing. T2 - SMAR 2019 CY - Potsdam, Germany DA - 27.08.2019 KW - Sensors KW - Passive RFID KW - Smart structures KW - SHT KW - Long term monitoring PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-501931 UR - https://www.ndt.net/?id=25011 SN - 1435-4934 VL - 25 IS - 1 SP - 1 EP - 6 PB - NDT.net CY - Kirchwald AN - OPUS4-50193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (less than1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. These effects are prominent in the meso-pore range and might significantly alter the effective diffusion coefficient. KW - Earth material KW - Material moisture KW - Physisoprtion KW - Chemisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-583811 DO - https://doi.org/10.1016/j.matpr.2023.09.034 SN - 2214-7853 SP - 1 EP - 8 PB - Elsevier Ltd. CY - Amsterdam, Niederlande AN - OPUS4-58381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Küttenbaum, Stefan T1 - Zur Visualisierung von Schäden in Betonschwellen durch zerstörungsfreie Ultraschallprüfung N2 - Die bildgebende Ultraschalltechnik liefert Hinweise auf verdeckte Schäden in Spannbetonschwellen. Dieses zerstörungsfreie Prüfverfahren schafft eine objektive und vergleichbare Basis für die Zustandsbestimmung der Schwellen und ermöglicht die Optimierung von baulichen Erhaltungsstrategien. KW - Spannbetonschwellen KW - Zustandsbewertung KW - Verkehrsinfrastruktur PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-592914 UR - https://www.eurailpress.de/magazine.html SN - 0013-2845 IS - 12/23 SP - 26 EP - 31 PB - DVV Media Group CY - Hamburg AN - OPUS4-59291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Küttenbaum, Stefan T1 - Zur Visualisierung von Schäden in Betonschwellen durch zerstörungsfreie Ultraschallprüfung N2 - Die bildgebende Ultraschalltechnik liefert Hinweise auf verdeckte Schäden in Spannbetonschwellen. Dieses zerstörungsfreie Prüfverfahren schafft eine objektive und vergleichbare Basis für die Zustandsbestimmung der Schwellen und ermöglicht die Optimierung von baulichen Erhaltungsstrategien. KW - Betonschwellen KW - Ultraschall KW - Schieneninfrastruktur KW - Gleisoberbau KW - Spannbetonschwelle PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-591889 UR - https://www.eurailpress.de/etr SN - 0013-2845 IS - 12 SP - 26 EP - 31 PB - DVV Media Group, Eurailpress CY - Hamburg AN - OPUS4-59188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan A1 - Braml, T. A1 - Taffe, A. A1 - Keßler, S. A1 - Maack, Stefan T1 - Reliability assessment of existing structures using results of nondestructive testing N2 - Making optimal decisions about the reliability of existing structures requires that the information used in assessment adequately represents the properties and the condition of the structures. The knowledge gap regarding a structure to be assessed can be successively filled by individually purposeful observations on site. This paper gives an overview of an approach for utilizing nondestructively gathered measurement results in reliability assessment of existing structures. An essential part of measurement-based stochastic modeling of basic variables is the calculation of measurement uncertainties, which serves to establish confidence in measurement, to ensure the comparability of unambiguously expressed measurement results, and to quantify the quality of the measured information. Regarding the current discourse on how to treat information collected on-site in the context of assessment, the authors recommend that measurement uncertainty becomes an uncertainty component mandatorily to be represented in measurement-based stochastic models. The main steps of the proposed concept are presented, and the advantages of its application are emphasized by means of a prestressed concrete bridge as case study. The bridge is assessed regarding the serviceability limit state decompression using ultrasonic and radar data measured at the structure. KW - Bridge KW - Measurement uncertainty KW - Prestressed concrete KW - Stochastic modeling KW - Probabilistic methods PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-529927 DO - https://doi.org/10.1002/suco.202100226 SN - 1751-7648 VL - 22 IS - 5 SP - 2895 EP - 2915 PB - John Wiley & Sons Ltd CY - Oxford AN - OPUS4-52992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -