TY - JOUR ED - Rossignol, S. ED - Gluth, Gregor T1 - Special issue: Alkali-activated materials and geopolymers in ceramics and beyond N2 - Geopolymers and alkali-activated materials have emerged as a complement, and partly as an alternative, to traditional materials in various applications, such as traditional ceramics, energy saving, waste management, building construction, and filtration. These new materials can play an important role in mitigating climate change and promoting a circular economy, which is one of the reasons why they are being actively researched in many laboratories around the world. Open Ceramics, the official, peer-reviewed, Open Access journal of the European Ceramic Society, is dedicated to foster this research and is compiling a Special Issue with the title “Alkali-activated and geopolymer materials in ceramics and various applications”. The aim of this Special Issue is to promote new applications, the use of previously underused raw materials, and in particular a better understanding of the chemical and mechanical behavior of these materials. The scope of the Special Issue includes, but is not limited to, research on the following topics: - valorization of previously underused raw materials - a better understanding of established raw materials - detailed spectroscopic characterization of alkali-activated materials and geopolymers to elucidate their phase assemblage - the mechanism of formation of the phase(s) that comprise these binders - control of their mechanical properties - the effect of fillers/aggregates on their mechanical properties - their durability under various conditions and the underlying deterioration mechanisms - special applications and recycling-related considerations. KW - Alkali-activated materials KW - Geopolymers PY - 2021 UR - https://www.sciencedirect.com/journal/open-ceramics/special-issue/10789KQV7BR SN - 2666-5395 SP - 100013-1 EP - 100184-12 PB - Elsevier CY - Amsterdam AN - OPUS4-51984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Durlo Tambara, Luís Urbano T1 - Influence of dredging mud on the calcium sulfoaluminate cement hydration N2 - Dredging sediment refers to materials removed from the bottom of a water body during dredging operations. Mainly the dreading mud contains clay, silt, sand, water, and alkalis. This work incorporated dredging mud into the calcium sulfoaluminate cement at replacement levels of 0%, 10%, 30%, and 50% by weight. Pastes were evaluated after 1d, 28d, and 90d- hydration through mechanical strengths and the reaction rate by isothermal conduction calorimetry. XRD and MIP characterized the reaction products. The findings showed that small replacements (10% and 30%) increased early strength with higher ettringite formation in the system at 1d of curing. However, the evolution of mechanical strength was lower than the reference (0% replacement) over time. The results showed that in low replacement dosages, the dredging mud act as a nucleation site for the hydration of calcium sulfoaluminate phases. T2 - 7th International Conference Non-Traditional Cement & Concrete (NTCC) CY - Brno, Czech Republic DA - 25.06.2023 KW - Calcium sulfoaluminate cement KW - Dredging mud KW - Hydration KW - Paste PY - 2023 AN - OPUS4-58054 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sittner, Jonathan T1 - Calcined clays: Innovative production of cost-effective and sustainable supplementary cementitious materials N2 - Calcined clays are promising sustainable alternative materials for cement production. By calcining natural clay minerals (usually 600–900 °C), they become reactive and can be used as a partial replacement for Portland clinker in cement production. This results in a lower carbon footprint and reduced energy consumption in the production process. Replacing cement clinker with so-called supplementary cementitious materials (SCM) such as fly ash and blast furnace slag has been done for several decades. Calcined clays have also been used, mostly in the form of metakaolin, which significantly improves the strength and durability of mortar and concrete. However, its limited availability and high cost restrict its practical application to a few specialist applications. In comparison, 2:1 clay minerals such as illite or smectites are more widely available and economically attractive due to their lower costs. Recent research has explored the use of calcined 2:1 clay minerals as SCM, but their properties and efficient production are still not fully understood. In the present work, different clays from Germany are characterized and tested as potential calcined clay. Besides conventional calcination using a rotary kiln, fluidized bed calcination is used to improve the reactivity of the calcined clays while being less time-consuming and therefore more energy efficient. T2 - GeoSaxonia 2024 CY - Dresden, Germany DA - 23.09.2024 KW - Calcined clay KW - Supplementary cementitious material (SCM) PY - 2024 AN - OPUS4-61973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mezhov, Alexander A1 - Kulisch, D. A1 - Goncharov, A. A1 - Zhutovsky, S. T1 - A Comparative Study of Factors Influencing Hydration Stoppage of Hardened Cement Paste N2 - There is no consensus on which hydration stoppage method is optimal to preserve the microstructure and mineral composition of samples, especially considering the specific aspects of different testing methods, such as TGA, MIP, or XRD. This paper presents a quantitative comparison between the most popular hydration stoppage strategies and parameters such as the sample piece size, the soaking time in a solvent, and the type, as examined on cement paste hydrated for 7 days. It was found that the carbonation appears either for samples smaller than 2.36 mm and bigger than 4.75 mm or samples soaked in a solvent for longer than 1 h. Fast solvent replacement leads to ettringite diminution and total pore volume increase. Among others, solvent replacement with subsequent gentle heating under a vacuum was found to be the most efficient, whereas it was experimentally demonstrated that isopropyl alcohol stops hydration faster than ethanol and acetone. KW - Hydration stoppage KW - Solvent replacement KW - Soaking time KW - Sample piece size PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-582430 DO - https://doi.org/10.3390/su15021080 VL - 15 IS - 2 SP - 1 EP - 21 PB - MDPI CY - Basel, Switzerland. AN - OPUS4-58243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Schönsee, Eric A1 - Jeyifous, Olubunmi Anthony A1 - Mezhov, Alexander A1 - Hüsken, Götz T1 - Introduction of a monitoring system for Bingham fluids in additive manufacturing with concrete N2 - Freeform additive manufacturing of concrete structures is a rising technology in civil engineering with several fascinating advantages. Nonetheless, to ensure reliability and structural integrity, standards and quality control are required in the future to bring this technology into the market. As the concrete is manufactured continuously, continuous quality control of the printing process is also required, i.e. comprehensive process monitoring. At BAM, a test rig will be installed, enabling the printing of concrete structures with a maximum size of 2 m x 1 m x 1 m (l x w x h). Here, process monitoring is the focus of the test rig. In this study, we show the results of the first pump tests, including the measurement of several parameters such as temperature and pressure along the supply system, i.e. from the concrete pump to the printer head. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Additive manufacturing of concrete KW - Process monitoring KW - Non-destructive testing KW - Bingham fluid PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-556367 SP - 1 EP - 12 AN - OPUS4-55636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Introduction of a monitoring system for Bingham fluids in additive manufacturing with concrete N2 - Freeform additive manufacturing of concrete structures is a rising technology in civil engineering with several fascinating advantages. Nonetheless, to ensure reliability and structural integrity, standards and quality control are required in the future to bring this technology into the market. As the concrete is manufactured continuously, continuous quality control of the printing process is also required, i.e. comprehensive process monitoring. At BAM, a test rig will be installed, enabling the printing of concrete structures with a maximum size of 2 m x 1 m x 1 m (l x w x h). Here, process monitoring is the focus of the test rig. In this study, we show the results of the first pump tests, including the measurement of several parameters such as temperature and pressure along the supply system, i.e. from the concrete pump to the printer head. T2 - NDT-CE 2022 CY - Zurich, Switzerland DA - 16.08.2022 KW - Additive manufacturing of concrete KW - Process monitoring KW - Non-destructive testing KW - Bingham fluid PY - 2022 AN - OPUS4-55637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmidt, Wolfram A1 - Rübner, Katrin A1 - Schneider, Joachim A1 - von Werder, Julia A1 - Gluth, Gregor T1 - 63. DAfStb-Forschungskolloquium in der BAM - Themenblock 2: Nachhaltigkeitspotentiale N2 - Die Bauindustrie ist für rd. 40 % des weltweiten Energieverbrauchs und der Kohlenstoffemissionen verantwortlich. Mit der technologischen Entwicklung wird der Energiebedarf in Zukunft sinken, während sich das Problem grauer Emission verschärft. Daher ist ein verantwortungsvoller Umgang mit Ressourcen der Schlüssel zur Erreichung der Pariser Klimaziele. Der Einsatz klimaschonender Baustoffe weist dabei ein erhebliches Nachhaltigkeitspotential auf. Recycling, Rückgewinnung, Ressourcenschonung und Kreislaufwirtschaft können zu unersetzlichen Bestandteilen der Bautechnik werden. Im Folgenden werden einige Möglichkeiten vorgestellt, die bei der Dekarbonisierung der Bautechnik zukünftig hohe Potentiale aufweisen. Diese wurden beim 63. Forschungskolloquium des DAfStb an der BAM vorgestellt und Details können dem Tagungsband (DOI 10.26272/opus4-61338) entnommen werden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Bindemittel KW - Klimaschonende Baustoffe KW - Dekarbonisierung PY - 2025 SN - 0005-9846 VL - 75 IS - 4 SP - 131 EP - 134 PB - concrete content UG CY - Schermbeck AN - OPUS4-63068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hüsken, Götz A1 - Strangfeld, Christoph A1 - Robens-Radermacher, Annika A1 - von Werder, Julia A1 - Weigel, Sandra A1 - Mezhov, Alexander T1 - 63. DAfStb-Forschungskolloquium in der BAM - Themenblock 3: Innovative Technologien N2 - Innovationen sind der Treiber des technologischen Fortschritts. Durch die Anwendung innovativer Technologien, Produktionsverfahren und neuer Materialien können Effizienzsteigerungen erzielt werden, die sowohl zu einer Kosten- als auch Materialreduzierung führen können. Gerade vor dem Hintergrund einer nachhaltigen Entwicklung sind Innovationen der Schlüssel zu einem verantwortungsvollen Umgang mit Ressourcen und Rohstoffen. Im Rahmen des 63. DAfStb-Forschungskolloquiums (Tagungsband: DOI 10.26272/opus4-61338) an der BAM wurden innovative Ansätze im Bereich effizienter Fertigungstechnologien und neuer Materialien vorgestellt, die nachfolgend kurz zusammengefasst werden. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Additive Fertigung KW - Biorezeptive Oberflächen KW - Biopolymere PY - 2025 SN - 0005-9846 VL - 75 IS - 4 SP - 134 EP - 135 PB - concrete content UG CY - Schermbeck AN - OPUS4-63069 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robens-Radermacher, Annika T1 - Modellierung und Simulation von 3D Betondruck – Design- und Prozessoptimierung N2 - Der 3D Betondruck ermöglicht die effiziente und ressourcenschonendere Herstellung maßgeschneiderter Betonstrukturen. Trotz des großen Potentials gibt es bisher keine einheitlichen Normen und Standards für den sicheren und robusten 3D Betondruck. Der Beitrag zeigt das Potential numerischer Methoden und Modelle zur effizienten und ressourcenschonenden Design- und Prozessoptimierung des 3D Betondrucks. Dazu werden die aktuellen Forschungsarbeiten im Bereich der Entwicklung robuster und zuverlässiger numerischer Zwillinge, geeigneter Optimierungstools sowie digitaler Workflows diskutiert. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - 3D Betondruck KW - Design- und Prozessoptimierung KW - Modellierung KW - Simulation PY - 2024 AN - OPUS4-61575 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kocherla, Amarteja A1 - Strangfeld, Christoph A1 - Hüsken, Götz T1 - Embedded Sensors for Quality Control and Structural Integrity Monitoring of Large-scale 3DCP Structures N2 - In extrusion-based 3D concrete printing (3DCP), addressing challenges related to safety, reliability, and quality control is crucial for widespread adoption. Yet current limitations in monitoring material properties during and after printing hinder the development of effective 3DCP guidelines. Therefore, the development of an inline sensing system capable of real-time monitoring and adjustment of process parameters is necessary to overcome these challenges. Building upon an existing inline sensing system developed by BAM, which currently monitors material properties during printing and the geometry of the print post-extrusion, this study extends its capabilities to post-extrusion monitoring using embedded piezoelectric (PZT) sensors. These PZT sensors provide localized measurements of material changes through electrical impedance (EI) measurements without disrupting the printing process. By embedding these sensors in 3D printed structures, continuous monitoring is achieved from layer deposition through 1-day of hydration. To achieve this, initially, PZT sensors were developed with multiple layers of protective coatings. Two different 3D printed mixtures, each with different hydration behaviors, were utilized, and PZT sensors were strategically placed between printed layers to maintain their integrity. EI measurements were collected continuously from printing through 1 day of hydration. Analysis of amplitude and frequency changes in the EI response spectrum provided insights into material behavior post-printing. The study highlights how continuous monitoring of frequency and conductance can track structural builtup and property development of the material. Rapid changes in conductance measurements, immediately post-printing indicate swift structural built-up, while key hydration phases are reflected in frequency measurements. T2 - 34th Annual Conference and Exhibition on Non Destructive Evaluation & Enabling Technologies CY - Chennai, India DA - 12.12.2024 KW - Embedded Sensors KW - 3D Concrete Printing KW - Quality Control KW - Inline Sensing KW - Structural Integrity PY - 2025 SP - 1 EP - 8 PB - Springer Nature CY - Heidelberg AN - OPUS4-65305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Grengg, C. A1 - Ukrainczyk, N. A1 - Mittermayr, F. A1 - Dietzel, M. T1 - Acid resistance of alkali-activated materials: Recent advances and research needs N2 - Cementitious materials are frequently applied in environments in which they are exposed to acid attack, e.g., in sewer systems, biogas plants, and agricultural/food-related industries. Alkali-activated materials (AAMs) have repeatedly been shown to exhibit a remarkably high resistance against attack by organic and inorganic acids and, thus, are promising candidates for the construction and the repair of acid-exposed structures. However, the reaction mechanisms and processes affecting the acid resistance of AAMs have just recently begun to be understood in more detail. The present contribution synthesises these advances and outlines potentially fruitful avenues of research. The interaction between AAMs and acids proceeds in a multistep process wherein different aspects of deterioration extend to different depths, complicating the overall determination of acid resistance. Partly due to this indistinct definition of the ‘depth of corrosion’, the effects of the composition of AAMs on their acid resistance cannot be unambiguously identified to date. Important parallels exist between the deterioration of low-Ca AAMs and the weathering/corrosion of minerals and glasses (dissolution-reprecipitation mechanism). Additional research requirements relate to the deterioration mechanism of high-Ca AAMs; how the character of the corroded layer influences the rate of deterioration; the effects of shrinkage and the bond between AAMs and substrates. KW - Alkali-activated materials KW - Acid attack KW - Acid resistance KW - Concrete repair KW - MIC PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557376 DO - https://doi.org/10.21809/rilemtechlett.2022.157 SN - 2518-0231 VL - 7 SP - 58 EP - 67 PB - RILEM Publications SARL CY - Paris AN - OPUS4-55737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Henning, Ricky A1 - Sturm, Patrick A1 - Geddes, D.A. A1 - Keßler, S. A1 - Walkley, B. A1 - Gluth, Gregor T1 - The influence of curing temperature on the strength and phase assemblage of hybrid cements based on GGBFS/FA blends N2 - Hybrid cements are composites made of Portland cement or Portland clinker and one or more supplementary cementitious materials like slag, fly ash or metakaolin, activated with an alkali salt. To date, their hydration mechanism and the phase formation at various temperatures is insufficiently understood, partly due to the large variability of the raw materials used. In the present study, three hybrid cements based on ground granulated blast furnace slag, fly ash, Portland clinker and sodium sulfate, and an alkali-activated slag/fly ash blend were cured at 10 and 21.5°C, and subsequently analyzed by XRD, 27Al MAS NMR, and TGA. The compressive strength of the hybrid cements was higher by up to 27% after 91-day curing at 10°C, compared to curing at 21.5°C. The experimental results as well as thermodynamic modeling indicate that the differences in compressive strength were related to a different phase assemblage, mainly differing amounts of strätlingite and C-N-A-S-H, and the associated differences of the volume of hydration products. While the strätlingite was amorphous to X-rays, it could be identified by 27Al MAS NMR spectroscopy, TGA and thermodynamic modeling. The microstructural properties of the hybrid cements and the alkali-activated slag/fly ash blend as well as the compatibility between thermodynamic modeling results and experimental data as a function of curing temperature and time are discussed. KW - Hybrid cements KW - Strätlingite KW - Thermodynamic modelling KW - Hydration PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557767 DO - https://doi.org/10.3389/fmats.2022.982568 SN - 2296-8016 VL - 9 SP - 1 EP - 16 PB - Frontiers AN - OPUS4-55776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Ke, X. A1 - Vollpracht, A. A1 - Weiler, L. A1 - Bernal, S. A. A1 - Cyr, M. A1 - Dombrowski-Daube, K. A1 - Geddes, D. A. A1 - Grengg, C. A1 - Le Galliard, C. A1 - Nedeljkovic, M. A1 - Provis, J. L. A1 - Valentini, L. A1 - Walkley, B. T1 - Carbonation rate of alkali-activated concretes and high-volume SCM concretes: a literature data analysis by RILEM TC 281-CCC N2 - The current understanding of the carbonation and the prediction of the carbonation rate of alkali-activated concretes is complicated inter alia by the wide range of binder chemistries used and testing conditions adopted. To overcome some of the limitations of individual studies and to identify general correlations between mix design parameters and carbonation resistance, the RILEM TC 281-CCC ‘Carbonation of Concrete with Supplementary Cementitious Materials’ Working Group 6 compiled and analysed carbonation data for alkali-activated concretes and mortars from the literature. For comparison purposes, data for blended Portland cement-based concretes with a high percentage of SCMs (≥ 66% of the binder) were also included in the database. The analysis indicates that water/CaO ratio and water/binder ratio exert an influence on the carbonation resistance of alkali-activated concretes; however, these parameters are not good indicators of the carbonation resistance when considered individually. A better indicator of the carbonation resistance of alkali-activated concretes under conditions approximating natural carbonation appears to be their water/(CaO + MgOeq + Na2Oeq + K2Oeq) ratio, where the subscript ‘eq’ indicates an equivalent amount based on molar masses. Nevertheless, this ratio can serve as approximate indicator at best, as other parameters also affect the carbonation resistance of alkali-activated concretes. In addition, the analysis of the database points to peculiarities of accelerated tests using elevated CO2 concentrations for low-Ca alkali-activated concretes, indicating that even at the relatively modest concentration of 1% CO2, accelerated testing may lead to inaccurate predictions of the carbonation resistance under natural exposure conditions. KW - Alkali-activated materials KW - Durability KW - Carbonation KW - Accelerated testing PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-560037 DO - https://doi.org/10.1617/s11527-022-02041-4 VL - 55 IS - 8 SP - 1 EP - 15 PB - Springer Nature AN - OPUS4-56003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Sebastian A1 - Bertmer, M. A1 - Gluth, Gregor T1 - Sol–gel synthesis and characterization of lithium aluminate (L–A–H) and lithium aluminosilicate (L–A–S–H) gels N2 - Hydrous lithium aluminosilicate (L–A–S–H) and lithium aluminate (L–A–H) gels are candidate precursors for glass-ceramics and ceramics with potential advantages over conventional processing routes. However, their structure before calcination remained largely unknown, despite the importance of precursor structure on the properties of the resulting materials. In the present study, it is demonstrated that L–A–S–H and L–A–H gels with Li/Al ≤ 1 can be produced via an organic steric entrapment route, while higher Li/Al ratios lead to crystallization of gibbsite or nordstrandite. The composition and the structure of the gels was studied by thermogravimetric analysis, X-ray diffraction, 27Al and 29Si magic-angle spinning nuclear magnetic resonance, and Raman spectroscopy. Aluminium was found to be almost exclusively in six-fold coordination in both the L–A–H and the L–A–S–H gels. Silicon in the L–A–S–H gels was mainly in Q4 sites and to a lesser extent in Q3 sites (four-fold coordination with no Si–O–Al bonds). The results thus indicate that silica-rich and aluminium-rich domains formed in these gels. KW - Lithium aluminosilicates KW - Raman spectroscopy KW - Sol-gel PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-558756 DO - https://doi.org/10.1111/ijac.14187 SN - 1546-542X VL - 19 IS - 6 SP - 3179 EP - 3190 PB - Wiley AN - OPUS4-55875 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bernal, S. A. A1 - Dhandapani, Y. A1 - Elakneswaran, Y. A1 - Gluth, Gregor A1 - Gruyaert, E. A1 - Juenger, M. C. G. A1 - Lothenbach, B. A1 - Olonade, K. A. A1 - Sakoparnig, M. A1 - Shi, Z. A1 - Thiel, C. A1 - Van den Heede, P. A1 - Vanoutrive, H. A1 - von Greve-Dierfeld, S. A1 - De Belie, N. A1 - Provis, J. L. T1 - Report of RILEM TC 281-CCC: A critical review of the standardised testing methods to determine carbonation resistance of concrete N2 - The chemical reaction between CO2 and a blended Portland cement concrete, referred to as carbonation, can lead to reduced performance, particularly when concrete is exposed to elevated levels of CO2 (i.e., accelerated carbonation conditions). When slight changes in concrete mix designs or testing conditions are adopted, conflicting carbonation results are often reported. The RILEM TC 281-CCC ‘Carbonation of Concrete with Supplementary Cementitious Materials’ has conducted a critical analysis of the standardised testing methodologies that are currently applied to determine carbonation resistance of concrete in different regions. There are at least 17 different standards or recommendations being actively used for this purpose, with significant differences in sample curing, pre-conditioning, carbonation exposure conditions, and methods used for determination of carbonation depth after exposure. These differences strongly influence the carbonation depths recorded and the carbonation coefficient values calculated. Considering the importance of accurately determining carbonation potential of concrete, not just for predicting their durability performance, but also for determining the amount of CO2 that concrete can re-absorb during or after its service life, it is imperative to recognise the applicability and limitations of the results obtained from different tests. This will enable researchers and practitioners to adopt the most appropriate testing methodologies to evaluate carbonation resistance, depending on the purpose of the conclusions derived from such testing (e. g. materials selection, service life prediction, CO2 capture potential). KW - Concrete KW - Cement KW - Carbonation KW - Testing KW - Standards PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-609364 DO - https://doi.org/10.1617/s11527-024-02424-9 VL - 57 SP - 1 EP - 31 PB - Springer Nature AN - OPUS4-60936 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Henning, Ricky A1 - Sturm, Patrick A1 - Keßler, S. A1 - Gluth, Gregor ED - Lothenbach, B. ED - Wieland, E. ED - Altmaier, M. T1 - Influence of salt aggregate on the degradation of hybrid alkaline cement (HAC) concretes in magnesium chloride-rich saline solution simulating evaporite rock N2 - Concretes produced from salt aggregate and hybrid alkaline cements, an alkali-activated slag/fly ash blend, or a Portland cement were exposed to a magnesium chloride-rich saline solution ([Mg2+] = 3.6 m, [Cl−] = 8.3 m), representing a solution formed after contact of surface water with evaporite rock (rock salt) in a nuclear waste repository. The hydration and deterioration of the concretes were studied with X-ray diffraction, thermogravimetric analysis, pH mapping and permeability measurements. The results show that calcium silicate hydrate (C-S-H) or sodium-substituted calcium aluminium silicate hydrate (C-N-A-S-H) and Friedel's salt were the major reaction products in the concretes prior to exposure to the saline solution. During exposure to the saline solution, increasing amounts of C-S-H/C-N-A-S-H dissolved, and gypsum and a secondary AFm phase formed. The durability of the concretes improved with increasing amounts of Portland clinker in the cements, due to the associated differences in permeability and chemical resistance. Nevertheless, a massive increase of permeability occurred for all concretes, likely caused by crack formation due to the formation of gypsum from anhydrite in the salt aggregate. Thus, the behavior of the concretes differed from, and was more complex than, the behavior of plain cement pastes. T2 - Joint 6th International Workshop on Mechanisms and Modelling of Waste/Cement Interactions (JCCW 2023) CY - Prague, Czech Republic DA - 20.11.2023 KW - Nuclear waste repository KW - Evaporite rock KW - Magnesium chloride brine KW - Concrete KW - Hybrid alkaline cement PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-599928 DO - https://doi.org/10.1016/j.apgeochem.2024.106027 SN - 0883-2927 SN - 1872-9134 VL - 168 SP - 1 EP - 14 PB - Elsevier AN - OPUS4-59992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grengg, C. A1 - Gluth, Gregor A1 - Mittermayr, F. A1 - Ukrainczyk, N. A1 - Bertmer, M. A1 - de Oliveira Guilherme Buzanich, Ana A1 - Radtke, Martin A1 - Leis, A. A1 - Dietzel, M. T1 - Deterioration mechanism of alkali-activated materials in sulfuric acid and the influence of Cu: A micro-to-nano structural, elemental and stable isotopic multi-proxy study N2 - In this study, a multi-proxy approach combining 29Si, 27Al and 1H MAS-NMR, FEG-EPMA, XANES at the Cu K-edge and XRD analytics with hydrochemical tools such as ICP-OES analyses, oxygen-isotope signatures, and thermodynamic modelling was applied to K-silicate-activated metakaolin specimens - with and without CuSO4·5H2O addition - exposed to sulfuric acid at pH = 2 for 35 days. The results revealed a multistage deterioration mechanism governed by (i) acid diffusion, (ii) leaching of K-A-S-H, (iii) microstructural damage related to precipitation of expansive (K,Ca,Al)-sulfate-hydrate phases (iv) complete dissolution of the K-A-S-H framework, (v) and formation of silica gel in the outermost corroded regions. Copper ions were mainly located in layered spertiniite-chrysocolla-like phases in the as-cured materials. The results demonstrate an overall negative effect of Cu addition on chemical material durability, implying that the reported higher durability of Cu-doped AAM in biocorrosion environments can be best explained by bacteriostatic effects. KW - Alkali-activated materials KW - Acid resistance KW - Microbially induced corrosion KW - MIC PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-520567 DO - https://doi.org/10.1016/j.cemconres.2021.106373 SN - 0008-8846 VL - 142 SP - 1 EP - 15 PB - Elsevier CY - Oxford AN - OPUS4-52056 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gluth, Gregor A1 - Ebell, Gino A1 - Hlavacek, Petr A1 - Mietz, Jürgen T1 - Chloride‐induced steel corrosion in alkali‐activated fly ash mortar: Increased propensity for corrosion initiation at defects N2 - Chloride contents at the steel–mortar interface that initiate steel corrosion were determined for carbon steel in alkali‐activated fly ash mortar for three different exposure conditions: exposure to 1 M NaCl solution; leaching in deionized water and then exposure to 1 M NaCl solution; and leaching in deionized water, aging in air at 20°C and natural CO2 concentration, and then exposure to 1 M NaCl solution. For comparison, a Portland cement mortar, exposed to 1 M NaCl solution, was studied. The median values of the corrosion‐initiating chloride contents (average over the full length of the rebar) in the alkali‐activated fly ash mortar varied between 0.35 and 1.05 wt% Cl with respect to binder, consistently lower than what was obtained for the Portland cement mortar, but with no clear trend regarding the exposure conditions. For most of the alkali‐activated fly ash mortar specimens, preferential corrosion at the connection between the working electrode and the external measurement setup was observed, while preferential corrosion did not occur for the Portland cement mortar. Scanning electron microscopy and auxiliary experiments in synthetic solutions indicated that this behavior was caused by inhomogeneities at the steel–mortar interface in the alkali‐activated mortar, likely due to its peculiar rheological properties in the fresh state. KW - Alkali-activated materials KW - Steel corrosion KW - Critical chloride content KW - Steel-concrete interface PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507268 DO - https://doi.org/10.1002/maco.202011541 VL - 71 IS - 5 SP - 749 EP - 758 PB - Wiley-VCH AN - OPUS4-50726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kazlagić, Anera A1 - Vogl, Jochen A1 - Gluth, Gregor A1 - Stephan, D. T1 - Provenancing of cement using elemental analyses and isotope techniques – The state-of-the-art and future perspectives N2 - With the aim of identifying the origin and the manufacturer of a cement, a reliable procedure that provides unambiguous results is needed. Such procedure could resolve practical issues in damage research, liability issues and forensic investigations. A substantial number of attempts for fingerprinting of building materials, including cement, has already been carried out during the last decades. Most of them were based on concentration analysis of the main elements/components. This review provides an overview of provenance studies of cement and the main approaches commonly used. Provenance studies of cement via isotope techniques are also presented and discussed as representatives of the state-of-the-art in the field. Due to the characteristic properties and the occurrence of carefully selected isotope ratios, unique fingerprints of different kinds of materials can be provided by these methods. This property has largely been explored in various scientific fields such as geo- and cosmochemistry, food forensics, archaeology, geochronology, biomedical studies, and climate change processes. However, the potential of isotope techniques in cement and concrete research for provenance studies has barely been investigated. Therefore, the review outlines a suitable approach using isotope ratios, which could lead to reliable provenancing of cementitious materials in the future. KW - Cement KW - Sr isotopes KW - Provenance PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-533762 DO - https://doi.org/10.1039/d1ja00144b VL - 36 IS - 10 SP - 2030 EP - 2042 PB - The Royal Society of Chemistry CY - Cambridge, UK AN - OPUS4-53376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Priebe, Nsesheye Susan T1 - Influence of calcination conditions and varying compositions on the reactivity and performance of brick clays as supplementary cementitious materials T1 - Der Einfluss von Kalzinierungsbedingungen und verschiedenen Zusammensetzungen auf die Reaktivität und Eigenschaften von Ziegeltonen verwendet als Zusatzstoffe in Beton N2 - Calcined clays as supplementary cementitious materials (SCMs) have been identified and credited to be a viable solution in mitigating the CO2 emissions related to cement production and consumption. Calcined clays range from a variety of different clay types based on an assortment of varying minerals and compositions. While extensive data is available on kaolinitic clays (based on the 1:1 clay type), other clays such as brick clays (based on the 2:1 clay type) are currently understudied, although such clays are largely more available than the kaolinitic clays. The aim of this thesis is to draw attention to the varying compositions present in two selected brick clays in Germany and elaborate on how such compositions affect their suitability to be used as SCMs in blended cement systems. The novelty of this thesis explains the relationship between the reactivity of the bricks to their varying compositions and their suitability for their employment as SCMs. This was based on their chemical and physical transformations in the calcination temperature range 650–900 or 950 °C, and the performance of the calcined brick clays in blended cement systems measured by their heat evolution, strength development and durability-related properties. The results of their performance were compared to two kaolinitic clays with varying compositions. While the kaolinitic clays generally exhibited the best performance as SCMs, the brick clay with a lower Fe2O3 content showed promising results similar to the kaolinitic clays when an optimum calcination temperature is applied and when substituted at a moderate cement substitution rate. Thus, this finding promoted further efforts made to improve the reactivity of the brick clay by producing a mixed clay composed of 50 % brick clay (with lower Fe2O3 content) and 50 % kaolinitic clay. The mixed clay was compared to the two individual brick clays and one kaolinitic clay, whereby optimum calcination conditions were performed in large-scale simulating an industrial-scale production of SCMs. All calcined clays exhibited pozzolanic reactivity, with the performance of the brick clays inferior to the kaolinitic clay, however, the mixed clay performed very similar to the kaolinitic clay. At a similar degree of hydration compared to plain Portland cement, the good performance of the mixed clays was especially evident in the strength development and improved chloride penetration resistance, which was caused by a refinement in the pore structure in the cementitious systems. Moreover, it was deduced that not only the high surface area, but also, the solubility of Si and Al ions in the resulting calcinate of the mixed clays plays a significant role when calcined at ~600–700 °C, which points to viable options for optimal employment of brick clays in cementitious systems. N2 - Die bei der Zementproduktion freigesetzte CO2-Menge und die daraus resultierenden Folgen für das Klima machen die Entwicklung von Zementersatzstoffen mit geringerem CO2-Fußabdruck erforderlich. Als besonders vielversprechend haben sich dabei die kalzinierten Tone erwiesen. Bei diesen handelt es sich um komplexe Systeme, bestehend aus einer Vielzahl verschiedener Tonminerale in variierender Konzentration und Zusammensetzung. Während für kaolinitische Tone (basierend auf 1:1 Tonmineralarten) bereits umfangreiche Daten gesammelt werden konnten, ist der Kenntnisstand zu anderen Tonarten z.B. Ziegeltonen (basierend auf 2:1 Tonmineralarten) derzeit noch unzureichend. Besonders vor dem Hintergrund der erheblich größeren Verfügbarkeit dieser Tonarten stellt dies einen erheblichen Nachteil dar. Ziel dieser Arbeit ist es, anhand zweier Ziegeltone aus Deutschland, aufzuzeigen welche Auswirkung die unterschiedliche Zusammensetzung der Tone sowohl auf die Reaktivität als auch auf den Einsatz als Zementersatzstoffen in Mischzementsystemen hat. Entsprechende Änderungen in der Zusammensetzung der kalzinierten Tone wurden durch die Variation der Kalzinierungstemperatur im Temperaturbereich zwischen 650 °C und 900 °C bzw. 950 °C und den folglich unterschiedlich ablaufenden chemischen und physikalischen Umwandlungsprozessen der Tonminerale erreicht. Die Leistungsfähigkeit dieser Systeme wurde anhand der Wärme- und Festigkeitsentwicklung sowie den Dauerhaftigkeitseigenschaften bewertet. Als Referenzsysteme dienten zwei 1:1 Tone mit unterschiedlicher Zusammensetzung. Die bei den 1:1 Tonen erzielten Reaktivitäten waren im Vergleich zu den Ziegeltonen zwar höher, aber bei entsprechender Kalzinierungstemperatur und moderater Zementersatzrate konnten auch bei den Ziegeltonen vielversprechende Ergebnisse erzielt werden. Basierend auf diesen Ergebnissen wurden in einem weiteren Schritt Mischtone, bestehend aus kaolinitischem Ton und Ziegelton mit geringerem Fe2O3 Gehalt (50:50), untersucht. Zur Bewertung wurden die zuvor untersuchten Ziegeltone und ein 1:1 Ton herangezogen. Bei allen kalzinierten Tonen konnte die pozzolanische Reaktion nachgewiesen werden, wobei der Ziegelton die geringsten und die 1:1 Tone die höchsten Werte lieferte. Das Mischtonsysteme sind leistungstechnisch bei den 1:1 Tonen einzuordnen. Die strukturverfeinernde Wirkung des Mischtons beim Einsatz als Zementersatz in Portlandzementsystemen führte sowohl bei der Festigkeitsentwicklung als auch beim Chlorideindringwiderstand zu einer Leistungssteigerung. Zudem konnte gezeigt werden, dass nicht nur die große spezifische Oberfläche, sondern auch die hohe Löslichkeit der Si- und Al-Ionen in den Kalzinaten der bei ~600-700 °C kalzinierten Mischtone einen großen Einfluss hat und den Einsatz der Ziegeltone in zementären Systemen begünstigt. Die Möglichkeit zur Herstellung von Zementersatzstoffen im industriellen Maßstab konnte durch Versuche im Großmaßstab ebenfalls nachgewiesen werden. KW - Blended cement KW - Brick clay KW - Calcined clay KW - Hydration KW - Illite KW - Kalzinierte Tone KW - Ziegelton PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:co1-opus4-58816 DO - https://doi.org/10.26127/BTUOpen-5881 SP - i EP - 153 PB - Brandenburgische Technische Universität Cottbus-Senftenberg CY - Cottbus AN - OPUS4-55048 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -