TY - JOUR A1 - Hüsken, Götz A1 - Shamsuddoha, Md A1 - Pirskawetz, Stephan A1 - Hofmann, Detlef A1 - Baeßler, Matthias A1 - Kühne, Hans-Carsten T1 - Potential of a Repair System for Grouted Connections in Offshore Structures: Development and Experimental Verification N2 - Grouted connections are intensively used in offshore rigs, platforms as well as jacket and monopile offshore wind turbine structures. Being located in remote offshore conditions, these connections can experience considerable adverse loading during their lifetimes. Degradation was reported inside similar connections, which were installed in the last three decades. Grouting in the offshore sites may often be proven difficult, which eventually leads to reduced load-bearing capacity of connections in the long run. Thus, repair and rehabilitation of such connections should be planned ahead to minimize operational delays and costs. In this study, scaled grouted connections were manufactured using a novel mould, whose integrity were monitored using digital image correlation (DIC). The connections were loaded under static load to visualize the main failure pattern using distributed fibre optic sensors and acoustic emission (AE) analysis. Grouted connections were then repaired using a cementitious injectable grout. The effectiveness of the grout injection was monitored using dye penetration technique. Finally, specimens are reloaded to identify the potential of such repair for grouted connections. KW - Offshore KW - Grouted connection KW - Fibre optic sensors KW - Acoustic emission analysis KW - Cracks KW - Repair KW - Rehabilitation KW - Static loading PY - 2021 DO - https://doi.org/10.1016/j.marstruc.2021.102934 VL - 77 SP - 102934 PB - Elsevier Ltd. AN - OPUS4-52059 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten T1 - Handlungshilfe zur Betoninstandsetzung N2 - Die TR Instandhaltung des Deutschen Instituts für Bautechnik wird als maßgebliches Bezugswerk der Betoninstandsetzung ür die Fachöffentlichkeit hinsichtlich ihrer Inhalte und Zielrichtung vorgestellt KW - Beton KW - Instandsetzung KW - Technische Regel KW - Planung KW - Ausführung KW - DIBt PY - 2021 UR - https://www.ingenieur.de/fachmedien/bauingenieur/ PB - VDI Fachmedien GmbH & Co. KG Unternehmen für Fachinformationen CY - Düsseldorf AN - OPUS4-52117 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rübner, Katrin A1 - Seher, Julia A1 - Müller, Constanze A1 - Müller, Anette A1 - Liebezeit, Steffen A1 - Schnell, Alexander A1 - Martin, Falk ED - Schermer, Detleff ED - Brehm, Eric T1 - REALight - Leichtgranulate und REA-Gips aus feinkörnigen sulfatbelasteten Bau- und Abbruchabfällen und industriellen Nebenprodukten N2 - Die Zielstellung des Forschungsprojekts REALight ist die Entwicklung eines Verfahrens zur Herstellung von Leichtgranulaten auf der Grundlage der Ergebnisse des BMBF-Projekts „Aufbaukörnungen“ unter Erweiterung der Technologie, um Gips zurückzugewinnen und weitere mineralische Einsatzstoffe zu nutzen. In einem thermischen Verfahren werden mineralische Bau- und Abbruchabfälle über ein rohstoffliches Recycling, d. h. einen thermisch-chemischen Stoffumwandlungsprozess, zu leichten Gesteinskörnungen verarbeitet. Dabei werden im Bauschutt vorhandene Sulfate zersetzt. In einer anschließenden Rauchgaswäsche werden die Sulfate abgetrennt. Sie können als Ersatz für REA-Gips verwendet werden. Dies ist Voraussetzung für die Übertragung der Produkt- und Verfahrensidee in die Praxis und für den Nachweis der Sulfatabtrennung und -rückgewinnung aus gipshaltigem Inputmaterial. Es werden Untersuchungen zur Verbreiterung der Rohstoffbasis durch Einkopplung spezifischer mineralischer Stoffströme durchgeführt, die im Ergebnis zu einer Reduktion des Blähmittelbedarfs und einer Absenkung der Brenntemperatur führen sollen. Die Herstellung ausreichender Mengen Leichtgranulate für eine umfassende Charakterisierung nach Norm und die Praxiserprobung in bekannten Anwendungen und neuen Einsatzfeldern ist ein weiteres Projektziel. KW - Bau- und Abbruchabfälle KW - Bauschutt KW - Leichtgranulat KW - Leichte Gesteinskörnung KW - Gipsrückgewinnung PY - 2024 UR - https://www.ernst-und-sohn.de/mauerwerk-kalender-2024-schwerpunkte-klimagerechtes-und-nachhaltiges-bauen-befestigungen-bauen-im?tab=inhalt#rs SN - 978-3-433-03408-8 SP - 515 EP - 518 PB - Ernst & Sohn CY - Berlin AN - OPUS4-60356 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seher, Julia T1 - Lightweight aggregates made from construction and demolition waste - Application in lightweight concrete and mortars N2 - Heterogeneous construction and demolition waste can be used as raw material to produce lightweight aggregates (LWA) similar to expanded clays. In the joint research project “REALight”, LWA were produced from masonry rubble in a thermal expanding process using a pilot production plant with a rotary kiln. Our research focuses on the characterisation of the novel LWA and their use in different hydraulically bound applications. Infra-lightweight concrete (ILC) was produced with the novel LWA, which accounts for two thirds of total aggregate volume, and Celitement, which is a hydraulic binder with a low carbon footprint. Its dry bulk density is ≤ 800 kg/m³. Strength and durability properties are comparable to ILC data from the literature. Lime-based repair mortars (LRM) containing LWA are beneficial for sandstone conservation due to their similar properties regarding porosity, water absorption and strength. A two-layer repair mortar system, which consists of a filling mortar to fill large voids and a covering mortar to modulate the surface texture to the historic sandstone, was developed. In our contribution, we present results of the LWA characterisation according to the European standard EN 13055:2016. Requirements and challenges of the use of the novel LWA in ILC and LRM are discussed. T2 - V. International Conference Progress of Recycling in the Built Environment (V. PRE) CY - Weimar, Germany DA - 10.10.2023 KW - CDW recycling KW - Lightweight aggregates KW - Masonry rubble KW - Lightweight concrete KW - Repair mortar PY - 2023 AN - OPUS4-58540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seher, Julia T1 - Anwendung der Leichtgranulate in Mörtel und Beton N2 - Im Verbundforschungsprojekt REALight wurden Leichtgranulate aus gemischtem Mauerwerkbruch in einem thermischen Blähverfahren im Pilotmaßstab hergestellt. Im Teilprojekt der BAM stand die Charakterisierung dieser Leichtgranulate und ihre Anwendung in gebundenen Systemen im Vordergrund. Im Rahmen des Abschlussvortrags wurden Ergebnisse zur Entwicklung von Steinergänzungsmörteln sowie Infraleichtbeton vorgestellt. T2 - Kolloquium "Nachhaltig effizient - Ressourcen des zukünftigen Bauens" CY - Berlin, Germany DA - 18.01.2024 KW - Leichtgranulat KW - Mauerwerkbruch KW - Steinergänzungsmörtel KW - Denkmalpflege KW - Infraleichtbeton KW - Leichtbeton PY - 2024 AN - OPUS4-59398 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Constanze A1 - Seher, Julia A1 - Martin, Falk A1 - Schnell, Alexander A1 - Rübner, Katrin T1 - Leichtgranulate aus gemischtem Mauerwerkbruch für die Anwendung in Infraleichtbeton T1 - Lightweight granular materials made from mixed masonry rubble for use in infra-lightweight concrete N2 - Infraleichtbeton zeichnet sich durch eine äußerst geringe Trockenrohdichte von maximal 800 kg/m³ aus, bei gleichzeitig ausreichender Festigkeit. Daraus resultieren geringe Wärme- und Schallleitfähigkeiten. Dies ermöglicht den Einsatz als Sichtbeton in Wandelementen ohne die Notwendigkeit einer zusätzlichen Dämmschicht. Vielversprechend erscheint der Einsatz von Leichtgranulaten in Infraleichtbeton, um seinen ökologischen Fußabdruck zu reduzieren und somit ein energieeffizientes und zugleich nachhaltiges Bauen zu ermöglichen. Die Leichtgranulate werden in einem thermo-chemischen Prozess aus gemischtem Mauerwerkbruch hergestellt. Ihre Verwendung bietet neben der Alternative zu herkömmlichen leichten Gesteinskörnungen auch die Möglichkeit, Abfallprodukte sinnvoll zu nutzen. In diesem Artikel werden die Leichtgranulate vorgestellt, ihre Anwendung in Infraleichtbeton geprüft und mit konventionellem Blähton verglichen. N2 - Infra-lightweight concrete exhibits an extremely low dry bulk density of up to 800 kg/m³ while also providing sufficient strength, resulting in low thermal and acoustic conductivity. This allows it to be used as exposed concrete in wall panels without requiring an additional insulating layer. Using lightweight granular materials in infra-lightweight concrete appears to be promising for reducing its environmental footprint and thus enabling energy-efficient and sustainable construction. Lightweight granules are produced from mixed masonry rubble in a thermo-chemical process. In addition to being an alternative to conventional lightweight aggregates, their use also provides the opportunity to put waste products to good use. This article reports on lightweight granules, their use in infra-lightweight concrete, and related tests in comparison to conventional expanded clay. KW - Infraleichtbeton KW - Leichtgranulat KW - Mauerwerkbruch KW - Recycling KW - Leichte Gesteinskörnungen PY - 2024 VL - 90 IS - 7 SP - 52 EP - 59 PB - Bauverlag CY - Gütersloh AN - OPUS4-60557 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hering, Marcus A1 - Agasty, Amit A1 - Costard, René A1 - Hüsken, Götz A1 - Chruscicki, Sebastian A1 - Hicke, Konstantin T1 - Explosion effects on reinforced concrete structures – A preliminary study of scaling laws N2 - Blast tests are required to investigate accidental or intentional blast events and to assess the level of protection for people and facilities in critical infrastructures. Conducting large-scale field tests for complex scenarios is very resource intensive. Reliable small-scale experiments are a promising alternative. However, the scaling laws for the design of reinforced concrete structures under blast loads are not sufficiently established. In our research work, a consortium made up of three BAM departments, focuses on reinforced concrete structures that are suitable for the standardization of scaled blast tests. As part of the feasibility study, blast tests were carried out on test specimens of different sizes on the BAM Test Site for Technical Safety (TTS). Various reinforced concrete plates were tested and subjected to different blast loads. The blast tests included various measurement techniques to quantify the blast load and the behavior of the reinforced concrete plate. The blast load was measured with flush-mounted piezoelectric pressure gauges, while accelerometers and embedded fiber optic sensor cables were used to characterize the dynamic behavior of the plate under blast loading. In addition, damage characteristics were also determined using distributed fiber optic sensing. The application of these measurement techniques as well as the use of different numerical software tools offer the possibility to verify or adapt the scaling laws. T2 - 19th International Symposium on Interaction of the Effects of Munitions with Structures (19th ISIEMS) CY - Bonn, Germany DA - 09.12.2024 KW - Scaling KW - Blast KW - Fiber optic sensing PY - 2024 SP - 1 EP - 9 AN - OPUS4-62258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit T1 - Replica scaling of RC slabs under blast loading: a preliminary assessment N2 - Blast testing is undoubtedly the most straightforward and direct method of evaluating the blast resistance of a structure. For the calibration and validation of numerical models as well, blast tests must be carried out. However, true-scale prototype testing under different blast loading scenarios is not always feasible. Reliable small-scale experiments are a promising alternative. Application of dimensional analysis and similarity principals can be found in different engineering fields. For applications to the phenomenon of shock wave propagation, Hopkinson-Cranz or cube-root scaling is a well-established concept. When it comes to the scaling the structural response, research has predominantly focused on structures made of metallic materials. Scaled investigations with concrete or reinforced concrete (RC) structures remain limited, specifically under blast loading. In a preliminary study, we tested RC slabs at two different scales under near-field blast loading. Replica scaling, which is geometrical scaling while using the same materials at different scales, was implemented in the construction of the test specimens. The assessment of scaling and the discrepancy in its application was investigated by characterizing the blast loads, dynamic response, and damage. The experiments were supplemented by numerical simulations of these scenarios. The quantification of scenario-and-response-specific discrepancy can be used to modify the scaling laws, so that a blast assessment can be performed based on resource efficient small-scale tests. T2 - 25th International Physical Security Forum CY - Schwarzenburg, Switzerland DA - 11.05.2025 KW - Blast KW - RC slabs KW - Scaling PY - 2025 AN - OPUS4-63184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Hering, Marcus T1 - Experimental and Numerical Analysis of Reinforced Concrete Structures Under Blast Loading: Scopes and Challenges N2 - Protection against terrorist or accidental scenarios in industrial settings requires suitable designs of structures to resist blast loads. Field testing as well as finite element simulations are among the techniques available to engineers in the understanding of the structural behavior against blast loading. As blast testing of complex scenarios can be very resource intensive, tests are generally performed for simplified scenarios. Numerical tools can be used to model these scenarios in order to get a better insight into blast loading, structural response and the resulting damage to the structure. In the next steps, the simplified scenario is successively modified in numerical simulations to incorporate complexities that cannot be covered in blast testing experiments. One of the conditions for this approach to work is that the original simplified numerical simulation is valid. The scopes and challenges encountered in such a validation are the focus of this presentation. A relatively ‘simple’ field test of a horizontal reinforced concrete (RC) slab subjected to blast loading is taken as an example for validation of the performance of numerical tools. The blast test incorporated various measurement techniques to quantify the blast load as well as the behavior of the RC slab. Blast load was measured using flush-mounted piezoelectric pressure gauges, whereas acceleration sensors and fiber-optic sensor cables were used to characterize the dynamic behavior of the slab under blast loading. Additionally, damage characteristics were ascertained also using fiber-optic sensing. The application of such measurement techniques, along with different numerical software available for the analysis of the scenario in question, demonstrate the scope of our contribution. T2 - 24th International Physical Security Forum Brussels CY - Brussels, Belgium DA - 15.04.2024 KW - Blast KW - Reinforced Concrete Structures KW - Numerical simulations PY - 2024 AN - OPUS4-60880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hering, Marcus T1 - Explosion effects on reinforced concrete structures: A preliminary study of scaling laws N2 - Blast tests are required to investigate accidental or intentional blast events and to assess the level of protection for people and facilities in critical infrastructures. Conducting large-scale field tests for complex scenarios is very resource intensive. Reliable small-scale experiments are a promising alternative. However, the scaling laws for the design of reinforced concrete structures under blast loads are not sufficiently established. In our research work, a consortium made up of three BAM departments, focuses on reinforced concrete structures that are suitable for the standardization of scaled blast tests. As part of the feasibility study, blast tests were carried out on test specimens of different sizes on the BAM Test Site for Technical Safety (TTS). Various reinforced concrete plates were tested and subjected to different blast loads. The blast tests included various measurement techniques to quantify the blast load and the behavior of the reinforced concrete plate. The blast load was measured with flush-mounted piezoelectric pressure gauges, while accelerometers and embedded fiber optic sensor cables were used to characterize the dynamic behavior of the plate under blast loading. In addition, damage characteristics were also determined using distributed fiber optic sensing. The application of these measurement techniques as well as the use of different numerical software tools offer the possibility to verify or adapt the scaling laws. T2 - 19th International Symposium on Interaction of the Effects of Munitions with Structures (19th ISIEMS) CY - Bonn, Germany DA - 09.12.2024 KW - Blast KW - Fiber optic sensing KW - Scaling PY - 2024 AN - OPUS4-62260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -