TY - JOUR A1 - Titscher, Thomas A1 - van Dijk, T. A1 - Kadoke, Daniel A1 - Robens-Radermacher, Annika A1 - Herrmann, Ralf A1 - Unger, Jörg F. T1 - Bayesian model calibration and damage detection for a digital twin of a bridge demonstrator N2 - Using digital twins for decision making is a very promising concept which combines simulation models with corresponding experimental sensor data in order to support maintenance decisions or to investigate the reliability. The quality of the prognosis strongly depends on both the data quality and the quality of the digital twin. The latter comprises both the modeling assumptions as well as the correct parameters of these models. This article discusses the challenges when applying this concept to realmeasurement data for a demonstrator bridge in the lab, including the data management, the iterative development of the simulation model as well as the identification/updating procedure using Bayesian inference with a potentially large number of parameters. The investigated scenarios include both the iterative identification of the structural model parameters as well as scenarios related to a damage identification. In addition, the article aims at providing all models and data in a reproducibleway such that other researcher can use this setup to validate their methodologies. KW - Damage detection KW - Finite element analysis KW - Load identification KW - Model updating KW - Estimation KW - System identification KW - Variational Bayesian statistics PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-574496 DO - https://doi.org/10.1002/eng2.12669 SN - 2577-8196 SP - 1 EP - 27 PB - Wiley CY - Hoboken, NJ AN - OPUS4-57449 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (< 1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. This effect becomes most prominent in the meso-pore range and might alter the effective diffusion coefficient by more than 100 %. T2 - 4th International Congress on Materials & Structural Stability CY - Rabat, Morocco DA - 08.03.2023 KW - Earth masonry KW - Material moisture KW - Molecular diffusion KW - Chemisoprtion KW - Knudsen effect KW - Physisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-571391 SP - 1 EP - 8 PB - RILEM CY - Champs-sur-Marne AN - OPUS4-57139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Stolpe, Heiko A1 - Wiehle, Philipp T1 - Moisture diffusion affected by the Knudsen effect in temporal changing pore networks N2 - Almost all building materials in civil engineering have an open porosity and interact with or are affected by the environmental conditions. Structures might suffer from effects such as moisture adsorption, carbonation, corrosion, penetration of salt ions and chemical substances, etc. In the hygroscopic range, these processes are mostly driven by diffusion. Due to the confinement of small pores (less than1 µm), the Knudsen effect reduces the molecular diffusion. This reduction can become more significant in case of temporal changing pore systems because of physisorption of water vapor, carbonation, or chemisorption. In this study, unstabilised earth blocks and earth masonry are investigated. In a first step, the pore size distribution of the blocks is measured and sorption isotherms are recorded in experiments. Besides the ordinary physisorption, the involved clay minerals undergo swelling or shrinking due to chemisorption. The following two effects must be considered: first, the reduction of the available pore space by the adsorbed water layer. For this, the Hillerborg sorption theory is used, which is a combination of the well-known Brunauer-Emmett-Teller sorption theory and the Kelvin equation. This allows the computation of adsorbed water layers even in curved pore geometries. Second, the variation of the initial pore size distribution due to chemisorption needs to be modelled. Based on these two models, the effective diffusion coefficient can be predicted. For validation, arrays of relative humidity sensors were embedded into a free-standing earth masonry wall. This monitoring was carried out over more than a year to have a broad variety of environmental conditions and was located in Berlin, Germany. The prediction of the effective diffusion coefficient can also be transferred to other processes and allows the investigation of materials having temporarily changing pore systems. Examples are the carbonation of cementitious materials, alkali silica reaction, calcium leaching of long-lasting structures, etc. These effects are prominent in the meso-pore range and might significantly alter the effective diffusion coefficient. KW - Earth material KW - Material moisture KW - Physisoprtion KW - Chemisorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-583811 DO - https://doi.org/10.1016/j.matpr.2023.09.034 SN - 2214-7853 SP - 1 EP - 8 PB - Elsevier Ltd. CY - Amsterdam, Niederlande AN - OPUS4-58381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Pitters, S. A1 - Wedel, F. A1 - Hindersmann, I. T1 - Developing a guideline for structural health monitoring of road bridges in Germany N2 - In recent years, Structural Health Monitoring (SHM) has become a useful and increasingly widely used tool for supporting lifetime extensions of existing bridges with known structural deficiencies or indications of potentially critical damages or damage processes. At the same time, methods and tools are emerging, which enable monitoring-informed predictive maintenance of new and existing bridges based on digital twins. The monitoring process – starting from the definition of monitoring actions and ending with decisions based on monitoring outcomes – is complex and requires expertise in structural engineering, operation and maintenance of bridges, metrology, and data analytics. To support German road authorities, engineering consultancies, building contractors and other stakeholders of the bridge management, the Federal Highway Research Institute (BASt) has initiated the development of a new guideline for applying SHM as part of the management of road bridges. The guideline will present various use cases and for each identified use case, it will propose a proven monitoring scheme. In addition, the guideline will provide guidance on assessing the benefits of SHM as well as a common approach to managing monitoring data as a systematic basis for integrating monitoring data in the bridge management. This contribution discusses the motivation, objectives, and scope of the guideline, describes its use case centric structure and outlines the proposed data management. T2 - IABMAS 2024 CY - Kopenhagen, Danmark DA - 24.06.2024 KW - Guideline KW - Structural health monitoring KW - Road bridges KW - Infrastructure PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613947 SN - 978-1-032-77040-6 DO - https://doi.org/10.1201/9781003483755-236 SP - 2009 EP - 2017 PB - CRC Press AN - OPUS4-61394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Herrmann, Ralf A1 - Degener, Sebastian A1 - Pirskawetz, Stephan A1 - Loewe, Anna ED - Rogge, Andreas ED - Meng, Birgit T1 - Monitoring an Türmen von Onshore Windenergieanlagen in Betonbauweise im Hinblick auf Ermüdung N2 - Der Beitrag stellt das Messkonzept sowie dessen Umsetzung für ein umfassendes Monitoringsystem an einer onshore Windenergieanlage mit einem Hybridturm vor. Dieses ist Bestandteil des Forschungsvorhabens Win-ConFat – Structure, welches neben der Validierung geeigneter Sensorik auch die Bewertung des Zustands und der möglichen Restlebensdauer der ermüdungsbeanspruchten Betonstruktur zum Ziel hat. Neben dem Monitoringsystem werden erste Messergebnisse aus den Betriebsdaten sowie vom Verhalten der Turmstruktur vorgestellt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Monitoring KW - Windenergieanlage und Hybridturm KW - Ermüdung KW - WinConFat – Structure PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613276 SN - 978-3-9818564-7-7 SP - 286 EP - 293 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61327 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hering, Marcus A1 - Fiedler, Georg A1 - Schubert, T. A1 - Hille, Falk A1 - Hüsken, Götz A1 - Beckmann, B. ED - Rogge, Andreas ED - Meng, Birgit T1 - Großmaßstäbliche Impaktversuche mit Stahlbetonplatten – Konzeptionierung und Vorbereitung N2 - Seit 1977 ist der Flugzeugabsturz ein wesentliches Belastungsszenario bei der Auslegung von Kernkraftwerken. Zur Untersuchung dieses Szenarios wurden umfassende Studien durchgeführt, welche die Reaktion von Stahlbetonkonstruktionen unter Stoßbelastung analysieren. Da großmaßstäbliche Experimente teuer und aufwendig sind, gewinnen skalierte Versuche zunehmend an Bedeutung. Im Rahmen eines Forschungsprojekts der TU Dresden und der BAM wurden Grundlagen für skalierte Impaktversuche im großen Maßstab geschaffen, um die Übertragbarkeit vom Labor- auf Realmaßstab zu ermöglichen. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Fallturm KW - Impakt KW - Stahlbetonbauteile PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613257 SN - 978-3-9818564-7-7 SP - 278 EP - 285 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61325 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deresse, N. E. A1 - Thiele, Marc A1 - Pirskawetz, Stephan A1 - Sarem, M. A1 - Francois, St. A1 - Verstrynge, E. T1 - Evaluation of Concrete Fatigue Damage with Elastic Wave-based Measurement Techniques N2 - The fatigue damage evolution and the fatigue life of quasi-brittle materials such as concrete are not yet completely understood. Accordingly to get better insights, researchers have recently been incorporating advanced measuring techniques in their fatigue experiments. In this research, acoustic emission techniques (AET), active ultrasonic, and deformation measurements are used to track the damage evolution of concrete samples subjected to fatigue loading. The samples are subjected to constant amplitude and stepwise fatigue loading in Brazilian splitting test set-ups. Initially, a good agreement is observed between the deformation and the ultrasonic measurements in capturing the crack propagation during Brazilian splitting tests. The three fatigue damage phases could be identified with all of the three techniques. The Phase II damage rates quantified by deformation measurements and AET in stepwise fatigue tests were used to predict the number of cycles to failure at various stress levels. The predictions were validated using the number of cycles to failure of the constant amplitude fatigue tests. T2 - 36th Conference of the European Working Group on Acoustic Emission CY - Potsdam, Germany DA - 18.09.2024 KW - Concrete KW - Acoustic emission KW - Ultrasonic testing KW - Fatigue PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-615677 DO - https://doi.org/10.58286/30228 SN - 1435-4934 VL - 29 IS - 10 SP - 1 EP - 10 PB - NDT.net AN - OPUS4-61567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferrier, Emmanuel A1 - Michel, Laurent A1 - Thiele, Marc A1 - Mercier, Julien T1 - Strain-rate effect on the bond strength of external bonded reinforced carbon fiber-reinforced polymer for concrete structure N2 - The aim of the presented study is to investigate the dynamic loading strength of an external bonded fiber-reinforced polymers (FRP) system under seismic loading. 16 bonded FRP samples under different loading speeds ranging as 0.0000167–0.8 m /s were examined to determine the characteristics of the FRP bond strength on the concrete. The mechanical tests involved measuring the concrete/FRP shear properties using a double-lap shear test. Sixteen concrete specimens were cast, strengthened and surface preparation, instrumented, and driven to failure in the LMC laboratory and the BAM laboratory (Germany). Dynamic loading increased the bonded strength mainly because of an increase in the concrete tensile strength. Experimental data are then analysed and competed with the equation given by the new European standard that develop the design of external bonded FRP. The characteristic properties and bonded strength obtained by design equation were compared. Based on the results design equation are modified. KW - EBR strengthening system KW - Desing bond strength KW - Durability PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625354 DO - https://doi.org/10.1016/j.conbuildmat.2025.140216 SN - 1879-0526 VL - 466 SP - 1 EP - 14 PB - Elsevier Ltd. AN - OPUS4-62535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Frei, Vivian A1 - Pirskawetz, Stephan A1 - Thiele, Marc A1 - Rogge, Andreas T1 - Ermüdungsverhalten von Beton für unterschiedliche Probekörpergeometrien N2 - Die heute in der Anwendung befindlichen Bemessungskonzepte für Ermüdung von Beton stammen zum Teil noch aus den 1990er Jahren und sind speziell hinsichtlich hochfester Betone konservativ ausgelegt. Um die Vorteile von Türmen für Windkraftanlagen, vor allem auch aus hochfesten Betonen, im Zuge des geplanten Ausbaus der Windenergieversorgung in Deutschland wirtschaftlich nutzbar zu machen, müssen diese Bemessungskonzepte weiterentwickelt werden. Dafür sind umfangreiche Untersuchungen zur Ermittlung von Bruchlastwechselzahlen und zur Charakterisierung der Schädigungsentwicklung unter Ermüdungsbeanspruchung erforderlich. Allgemein anerkannte bzw. verbindliche Regelwerke oder Verfahren zur experimentellen Bestimmung der Ermüdungsfestigkeit (Bruchlastwechselzahlen) an Betonproben gibt es zurzeit aber nicht und die bisher durchgeführten Untersuchungen variieren in Parametern wie Probengeometrie, Probengröße und Prüffrequenz. Eine vergleichende Analyse der Ergebnisse der Studien und insbesondere die Übertragbarkeit auf bauteilrelevante Abmessungen ist auf dieser Grundlage nur sehr eingeschränkt möglich. KW - Ermüdungsverhalten KW - Probekörpergeometrien KW - Druckschwellenversuch KW - Bruchlastwechselzahlen KW - Beton PY - 2023 UR - https://www.betonverein.de/dbv-heft-52-materialermuedung-von-stahl-und-spannbeton-unter-hochzyklischer-beanspruchung-ergebnisse-des-verbundforschungsvorhabens-win-con-fat IS - 52 SP - 19 EP - 22 PB - Deutscher Beton- und Bautechnik-Verein E.V. CY - Berlin AN - OPUS4-58746 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Viefhues, Eva A1 - Döhler, M. A1 - Hille, Falk A1 - Mevel, L. T1 - Fault detection for linear parameter varying systems under changes in the process noise covariance N2 - Detecting changes in the eigenstructure of linear systems is a comprehensively investigated subject. In particular, change detection methods based on hypothesis testing using Gaussian residuals have been developed previously. In such residuals, a reference model is confronted to data from the current system. In this paper, linear output-only systems depending on a varying external physical parameter are considered. These systems are driven by process noise, whose covariance may also vary between measurements. To deal with the varying parameter, an interpolation approach is pursued, where a limited number of reference models – each estimated from data measured in a reference state – are interpolated to approximate an adequate reference model for the current parameter. The problem becomes more complex when the different points of interpolation correspond to different noise conditions. Then conflicts may arise between the detection of changes in the eigenstructure due to a fault and the detection of changes due to different noise conditions. For this case, a new change detection approach is developed based on the interpolation of the eigenstructure at the reference points. The resulting approach is capable of change detection when both the external physical parameter and the process noise conditions are varying. This approach is validated on a numerical simulation of a mechanical system. T2 - 21st IFAC World Congress CY - Online meeting DA - 13.07.2020 KW - Linear parameter varying systems KW - Fault detectionchanging KW - Process noise KW - Subspace-based residual KW - Model interpolation PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-524652 DO - https://doi.org/10.1016/j.ifacol.2020.12.868 SN - 2405-8963 VL - 53 IS - 2 SP - 13668 EP - 13673 PB - Elsevier AN - OPUS4-52465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weise, Frank A1 - Stelzner, Ludwig A1 - Recknagel, Christoph A1 - Pittrich, Tim A1 - Neugum, Tim A1 - Hering, Marcus A1 - Fiedler, Georg A1 - Thiele, Marc A1 - Simon, Patrick A1 - Maack, Stefan T1 - 63. DAfStb-Forschungskolloquium in der BAM - Themenblock 5: Bauteile und Bauwerke N2 - Ein weiterer Fokus des 63. DAfStb-Forschungskolloquiums (Tagungsband: DOI 10.26272/opus4-61338) lag auf den Bauteil- und Bauwerksuntersuchungen. Insbesondere wurde hier ein Einblick in die Forschungsaktivitäten in den BAM-Themenfeldern „Infrastruktur“ und „Energie“ gegeben. Thematisch wird dabei der Bogen von der Dauerhaftigkeit von Betonfahrbahndecken über die Extrembeanspruchung von Bauteilen und Bauwerken mittels Brand und Impact bis zum Bauwerksmonitoring und der Zustandsanalyse von Bestandsbauwerken gespannt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Dauerhaftigkeit von Betonfahrbahndecken KW - Alkali-Kieselsäurereaktion KW - Brand Impact KW - Bauwerksmonitoring PY - 2025 SN - 0005-9846 VL - 75 IS - 4 SP - 138 EP - 140 PB - concrete content UG CY - Schermbeck AN - OPUS4-63071 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bartels, Jan-Hauke A1 - Xu, Ronghua A1 - Kang, Chongjie A1 - Herrmann, Ralf A1 - Marx, Steffen T1 - Experimental Investigation on the Transfer Behavior and Environmental Influences of Low-Noise Integrated Electronic Piezoelectric Acceleration Sensors N2 - Acceleration sensors are vital for assessing engineering structures by measuring properties like natural frequencies. In practice, engineering structures often have low natural frequencies and face harsh environmental conditions. Understanding sensor behavior on such structures is crucial for reliable masurements. The research focus is on understanding the behavior of acceleration sensors in harsh environmental conditions within the low-frequency acceleration range. The main question is how to distinguish sensor behavior from structural influences to minimize errors in assessing engineering structure conditions. To investigate this, the sensors are tested using a long-stroke calibration unit under varying temperature and humidity conditions. Additionally, a mini-monitoring system configured with four IEPE sensors is applied to a small-scale support structure within a climate chamber. For the evaluation, a signal-energy approach is employed to distinguish sensor behavior from structural behavior. The findings show that IEPE sensors display temperature-dependent nonlinear transmission behavior within the low-frequency acceleration range, with humidity having negligible impact. To ensure accurate engineering structure assessment, it is crucial to separate sensor behavior from structural influences using signal energy in the time domain. This study underscores the need to compensate for systematic effects, preventing the underestimation of vibration energy at low temperatures and overestimation at higher temperatures when using IEPE sensors for engineering structure monitoring. KW - Acceleration sensors KW - Environmental influence KW - IEPE KW - Structural Health Monitoring KW - Low-frequency shaker PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594623 UR - https://www.mdpi.com/2673-8244/4/1/4/ DO - https://doi.org/10.3390/metrology4010004 SN - 2673-8244 VL - 4 IS - 1 SP - 46 EP - 65 PB - MDPI CY - Basel AN - OPUS4-59462 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Glienke, R. A1 - Kalkowsky, F. A1 - Hobbacher, A. F. A1 - Holch, A. A1 - Thiele, Marc A1 - Marten, F. A1 - Kersten, R. A1 - Henkel, K.-M. T1 - Evaluation of the fatigue resistance of butt‑welded joints in towers of wind turbines - A comparison of experimental studies with small scale and component tests as well as numerical based approaches with local concepts N2 - Wind turbines are exposed to a high number of load cycles during their service lifetime. Therefore, the fatigue strength verification plays an important role in their design. In general, the nominal stress method is used for the fatigue verification of the most common used butt-welded joints. The Eurocode 3 part 1–9 is the current design standard for this field of application. This paper presents recent results of fatigue tests on small-scaled specimens and large components with transverse butt welds to discuss the validity of the FAT-class. Furthermore, results from numerical simulations for the verification with the effective notch stress and the crack propagation approach are used for comparison. Based on the consistency between the numerical results and the fatigue tests, the influence of the seam geometry on the fatigue resistance was investigated. Finally, a prediction of the fatigue strength of butt-welded joints with plate thicknesses up to 80 mm was carried out. KW - Transverse butt weld KW - Weld imperfections KW - Wind turbine tower KW - Fatigue strength KW - Local approaches KW - Large components KW - Wind energy PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-596648 DO - https://doi.org/10.1007/s40194-023-01630-3 SN - 1878-6669 SP - 1 EP - 26 PB - Springer CY - Berlin AN - OPUS4-59664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wedel, F. A1 - Pitters, S. A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Hille, Falk A1 - Hindersmann, I. T1 - Guideline for the strategic application of monitoring of road bridges in Germany N2 - Engineering structures are an important part of our transport infrastructure. Their failure is associated with high safety risks and economic damage. Ensuring the availability of these constructions and guaranteeing their operational safety are thus important tasks. Currently, maintenance of engineering structures is a reactive process and therefore not yet a predictive process. Every 3 to 6 years, the structures are visually inspected, all damages are documented and a condition grade is assigned to the structure based on the detected damages. Continuous data-providing methods such as monitoring are used only very occasionally. With the help of monitoring, condition data about the structures are continuously collected, which can be used for a better assessment of the structures. On the one hand, this would increase safety of engineering structures, and on the other hand, it makes the shift towards predictive maintenance management based on real-time data and predictions, where the onset of damage is detected before it occurs, possible in the first place. Monitoring plays therefore an important role in the management of the infrastructure. It is a crucial a step towards the digitalisation of our infrastructure and existing processes. Although there are many use cases for monitoring that have already been successfully implemented, monitoring is not yet widely used by German road authorities due to several challenges that were also identified within the scope of the project. Therefore, a guide has been developed in which the current obstacles related to monitoring are identified and possibilities for integrating monitoring into existing processes are offered. To ensure optimal alignment with the needs of road authorities, both an online survey and a workshop have been conducted. The results are summarised in a brochure that is made available to authorities to improve the use of monitoring in Germany. This paper presents the guideline and the brochure. T2 - 10th European Workshop on Structural Health Monitoring (EWSHM 2024) CY - Potsdam, Germany DA - 10.06.2024 KW - Verkehrsinfrastrukturen KW - Engineering Structures KW - Bridges KW - Structural Health Monitoring KW - Guideline PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612821 UR - https://www.ndt.net/search/docs.php3?id=29582 DO - https://doi.org/10.58286/29582 SN - 1435-4934 VL - 29 IS - 7 SP - 1 EP - 8 PB - NDT.net GmbH & Co. KG CY - Mayen AN - OPUS4-61282 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Thiele, Marc A1 - Löhr, Manuel A1 - Loewe, Anna A1 - Degener, Sebastian A1 - Herrmann, Ralf T1 - Acoustic emission for monitoring of fatigue damage in concrete elements of wind turbine towers N2 - Wind energy has become an important player in the energy transition in Germany. Towers of onshore wind turbines are often designed as hybrid structures: the lower part is made of prestressed concrete whereas the upper part is made of steel tubes. The tall structures are permanently subjected to cyclic loads. A research project of BAM as part of the joint project WinConFat - Structure focusses on the evelopment of techniques to monitor fatigue damage evolution in the concrete part. Results of a previous project show that a combination of ultrasonic and acoustic emission testing can give an indication for critical conditions near the end of the fatigue life of the concrete. In the ongoing project acoustic emission sensors have been installed at the base and at the transition piece between concrete and steel of a hybrid wind turbine tower. Beside of acoustic emission measurement the sensor spacing allows for measuring the concrete ultrasonic velocity along the circumference in both levels. Additional measurements like strain, temperature, inclination, or acceleration allow for comparison of environmental loads and change of acoustic properties of the concrete. The paper focusses on first acoustic measurements recorded since December 2023 in comparison to operating data of the wind turbine. T2 - EWGAE2024: 36th Conference of the European Working Group on Acoustic Emission CY - Potsdam, Germany DA - 18.09.2024 KW - Concrete fatigue monitoring KW - Acoustic emission KW - Ultrasound KW - Hybrid wind turbine tower PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612197 DO - https://doi.org/10.58286/30234 SN - 1435-4934 VL - 29 IS - 10 SP - 1 EP - 9 AN - OPUS4-61219 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Pitters, S. A1 - Ramasetti, Eshwar Kumar A1 - Schneider, Ronald A1 - Wedel, F. A1 - Hindersmann, I. ED - Rogge, Andreas ED - Meng, Birgit T1 - Föderiertes Datenmanagement von Monitoringdaten aus Structural Health Monitoring Anwendungen und daraus gewonnenen Trainingsdaten bei Spannbetonbrücken N2 - Beim Structural Health Monitoring entstehen eine Vielzahl von Daten, Metadaten und Modellen mit hohem Wert für die Beurteilung des Bauwerkszustands und der Prognose von Veränderungen. Kontinuierlich anwachsende Datenbestände müssen nachhaltig geteilt, genutzt und über die Bauwerkslebensdauer archiviert werden. Dabei stellen die Vielfalt der Messaufgaben, die Heterogenität der Daten, die dezentrale Erfassung und z. T. der Umfang eine Herausforderung für die beteiligten Akteure dar. Für den Datentransfer der Monitoringdaten zwischen der Straßenbauverwaltung und den Monitoringausführenden wird ein flexibles Abstimmungsverfahren vorgeschlagen und ein Lösungskonzept für ein föderiertes Datenmanagement skizziert. Eine weitere Herausforderung stellt die bauwerksübergreifende Zusammenstellung von Trainingsdaten für konkrete KI-Anwendungen dar. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Structural Health Monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612902 SN - 978-3-9818564-7-7 SP - 178 EP - 185 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61290 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Pitters, S. A1 - Hindersmann, I. A1 - Schneider, Ronald A1 - Wedel, F. ED - Rogge, Andreas ED - Meng, Birgit T1 - Leitfaden für den strategischen Einsatz von Monitoring an Straßenbrücken N2 - Für die Anwendung von Structural Health Monitoring (SHM) im Rahmen des Managements von Straßenbrü-cken wurde zur Unterstützung von Straßenbauverwaltungen, Ingenieurbüros, Bauunternehmen und weiteren Akteuren die Erstellung eines Leitfadens initiiert. Dieser Leitfaden stellt typische Anwendungsfälle für Monito-ring vor und schlägt für diese bewährte Herangehensweisen vor. Darüber hinaus bietet der Leitfaden Empfeh-lungen für Ausschreibung und Vergabe von Monitoringleistungen, eine Anleitung zur Bewertung des wirt-schaftlichen Nutzens von SHM, Hinweise zur optimal einsetzbaren Messtechnik sowie einen Ansatz für das Datenmanagement zur Integration der Monitoringdaten in das Brückenmanagement. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Leitfaden KW - Monitoring KW - Straßenbrücke PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612931 SN - 978-3-9818564-7-7 SP - 186 EP - 191 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61293 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiehle, Philipp A1 - Härder, M. A1 - Strangfeld, Christoph T1 - Moisture behaviour of earth block masonry under natural climate conditions – experimental and numerical studies N2 - The compressive stength of unstabilised earth masonry depends on the moisture content. Knowledge of the moisture content is necessary in order to be able to account for the impact of moisture on the structural design of earth block masonry. For conventional building materials it is possible to precisely forecast the component moisture according to the layered structure on the basis of hygrothermal simulations. However , it is still not clear to what degree these numerical calculations can offer valid results for earth building materials. Earth building materials have a number of special properties related to moisture storage and moisture transport that differ significantly from the physical simplifications that are a component of existing material models. The swelling and shrinking of earth materials and their organic components results in changes to the pore space, the sorption behaviour exhibits a clear hysteresis, and the experimental determination of hygrothermal parameters in continuous contact with liquid water is almost impossible. To adequately forecast the moisture content of earth block masonry under natural climate conditions, extensive investigations of the moisture behaviour of load-bearing earth block masonry have been carried out within the framework of this project. These efforts began with the performance of magnetic resonance spectroscopic tests on two load-bearing earth blocks, in order to quantify the adsorption and desorption processes at relative humidities of between 50 % and 90 % under controlled, isothermal laboratory conditions. Once this had been done, a modified test setup was used to determine the water absorption coefficient , from which the liquid transport coefficients were derived. Based on the hygrothermal parameters values that were thus determined, the model was calibrated using the WUFI software program [7]. Finally, long-term moisture measurements were conducted on an earth block masonry wall that was ex-Increasing shortages of raw materials and rising energy prices are resulting in continuous growth in the demand for earth construction. In comparison to conventional building materials, earth building materials offer three significant advantages that have become even more important in light of the energy crisis in 2021 and the associated increase in the price of building supplies by approx. 40 percent [1]. Firstly, water solubility makes it possible to fully separate and recover all of the material components, and in particular the sand component. Secondly, energy-intensive firing processes, such as those required for cement production or brick manufacture, are eliminated. And thirdly, earth is a local raw material that is available in large quantities [1]. However, the load-bearing capacity of earth building materials is very much dependent on the moisture content. An increase in the relative humidity results in a reduction in the clay mineral cohesion , and this in turn results in a decline in both the compressive strength and the modulus of elasticity. In this regard, the mechanical properties of earth block masonry change in inverse proportion to the relative humidity. In other words, with every percentage point increase in relative humidity, both the compressive strength and the modulus of elasticity decline by one percent [2] [4]. The internal walls of heated living areas are generally only subject to relatively small fluctuations in relative humidity (between 40 % and 60 %) [5], and short periods in excess of these levels (such as in bathrooms or kitchens) only lead to a significant increase in the moisture content of the uppermost layers [6]. Exterior walls, on the other hand, are subject to large seasonal fluctuations in temperate climates, with a relative humidity in excess of 90 % in winter months. However, the exterior walls of heated living areas must be insulated in accordance with the German Buildings Energy Act (GEG), and with masonry this is generally done us T2 - LEHM 2024 – 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Earth stone KW - Masonry KW - Material moisture KW - Moisture monitoring KW - Hygrothermal simulations PY - 2024 SP - 1 EP - 10 AN - OPUS4-61220 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Signorini, C. A1 - Bracklow, F. A1 - Hering, Marcus A1 - Butler, M. A1 - Leicht, L. A1 - Schubert, T. A1 - Beigh, M. A. B. A1 - Beckmann, B. A1 - Curbach, M. A1 - Mechtcherine, V. T1 - Ballistic limit and damage assessment of hybrid fibre-reinforced cementitious thin composite plates under impact loading N2 - Impact resistance of reinforced concrete (RC) structures can be significantly improved by strengthening RC members with thin composite layers featuring high damage tolerance. Indeed, to limit the well-known vulnerability of cement-based materials against impact loading, the synergistic effects of short fibres and continuous textile meshes as hybrid reinforcement has been proved to be highly beneficial. This paper addresses the characterisation of novel cement-based hybrid composites through accelerated drop-weight impact tests conducted on rectangular plates at different impact energies. Two distinct matrices are assessed, with particular interest in a newly developed limestone calcined clay cement (LC3)-based formulation. Important parameters quantifying energy dissipation capability, load bearing capacity and damage are cross-checked to compute the ballistic limit and estimate the safety-relevant characteristics of the different composites at hand. Although textiles alone can improve the damage tolerance of fine concrete to some extent, the crack-bridging attitude of short, well-dispersed fibres in hybrid composites imparts a certain ductility to the cement-based matrices, allowing a greater portion of the textile to be activated and significantly reducing the amount of matrix spalling under impact. KW - Impact loading KW - Cement-based composites KW - SHCC KW - TRC KW - Sustainable binders PY - 2023 DO - https://doi.org/10.1016/j.jobe.2023.108037 VL - 80 SP - 1 EP - 21 PB - Elsevier Ltd. AN - OPUS4-58793 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Hering, Marcus T1 - Eine Machbarkeitsstudie zur Skalierung von Sprengversuchen an Stahlbetonbauteilen N2 - Sprengversuche sind erforderlich, um Explosionsereignisse auf Grund von Unfällen oder Anschlägen zu untersuchen und um das Schutzniveau für Menschen und Anlagen in kritischen Infrastrukturen zu bewerten. Die Durchführung von Feldversuchen in großem Maßstab für komplexe Szenarien ist sehr ressourcenintensiv. Verlässliche Experimente im kleinen Maßstab sind eine vielversprechende Alternative. Die Skalierungsgesetze für die Bemessung von Stahlbetonkonstruktionen unter Explosionsbelastung sind jedoch nicht hinreichend etabliert. Die Forschungsarbeit fokussiert sich auf Stahlbetonstrukturen, die für die Standardisierung von skalierten Sprengversuchen in Frage kommen. Im Rahmen der Machbarkeitsstudie wurden auf dem TTS-Gelände Sprengversuche an Probekörpern unterschiedlicher Größe durchgeführt. Dabei wurden verschiedene horizontal gelagerte Stahlbetonplatten getestet und unterschiedlichen Explosionsbelastungen ausgesetzt. Die Sprengversuche umfassten verschiedene Messtechniken zur Quantifizierung der Explosionslast sowie des Verhaltens der Stahlbetonplatten. Die Explosionslast wurde mit bündig eingebauten piezoelektrischen Druckmessern gemessen, während Beschleunigungssensoren und flächig applizierte verteilte faseroptische Sensorik verwendet wurden, um das dynamische Verhalten der Platte unter Explosionsbelastung zu charakterisieren. Darüber hinaus wurden Schädigungsmerkmale ebenfalls mit verteilter faseroptischer Sensorik ermittelt. Die Anwendung solcher Messtechniken sowie die Nutzung verschiedener numerischer Softwaretools bieten die Möglichkeit die Skalierungsgesetze zu verifizieren bzw. anzupassen. T2 - BBK - Fachkongress Forschung für den Bevölkerungsschutz 2025 CY - Bonn, Germany DA - 05.02.2025 KW - Sprengversuch KW - Skalierung KW - Faseroptik PY - 2025 AN - OPUS4-62509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lehmann, F. A1 - Hille, Falk T1 - Dauerüberwachung von Ingenieurbauwerken - Das neue Merkblatt B 09 der DGZfP T1 - Permanent monitoring of engineering structures The new leaflet B 09 of the DGZFP N2 - Messtechnische Systeme zur Dauerüberwachung von Bauwerken ermöglichen Einblicke in deren reale Trag- und Verformungsverhalten. Die Planung und technische Umsetzung solcher Maßnahmen erfordern für die erfolgreiche Erfüllung der Aufgabenstellungen eine hohe Fachkompetenz, sowohl auf der planerischen Seite, als auch für die fachliche Bewertung von angebotenen Monitoringlösungen. Als Hilfestellung dafür wurde von der Deutschen Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) das Merkblatt „Dauerüberwachung von Ingenieurbauwerken“ erarbeitet, welches nun verfügbar ist. In diesem Beitrag werden die Inhalte des neuen Merkblatts vorgestellt und dieses in die vorhandene Literatur eingeordnet. KW - Structural Health Monitoring KW - Brücken KW - Windenergieanlagen KW - Merkblatt KW - Bauwerksüberwachung KW - Richtlinie PY - 2023 DO - https://doi.org/10.1002/best.202200122 VL - 118 IS - 4 SP - 275 EP - 280 PB - Ernst & Sohn AN - OPUS4-57302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, T. A1 - Bracklow, F. A1 - Unger, N. A1 - Hering, Marcus A1 - Beckmann, B. T1 - Impact Tests on Reinforced Concrete Slabs – Variation in Results and Residual Load Bearing Capacity due to Hard Impact N2 - Structures such as concrete slabs and concrete barriers of critical infrastructure facilities must be able to withstand impact events or severe accidents. In particular, the structural safety of the confinements of nuclear power plants against a possible aircraft impact is essential to ensure the safety of inhabitants and environment. This article presents research results of hard impact on reinforced concrete slabs, which have been carried out at the Institute of Concrete Structures (IMB) at TUD Dresden University of Technology Technische Universität (TU Dresden). A specially designed drop tower is available for this purpose on the premises of the Otto Mohr Laboratory of TU Dresden. In the framework of a research project many reinforced concrete slabs of dimension 1.5 x 1.5 x 0.2 m³ were tested by hard impact. The investigation on some already carried out impact tests on reinforced concrete slabs intend to show the range of deviation of impact tests. In particular, the possible standard deviations that should be regarded in impact tests are estimated for the applied test setup. Furthermore, the residual structural capacity of an undamaged and damaged reinforced concrete slab has been investigated. T2 - Conference: 27th International Conference on Structural Mechanics in Reactor Technology (SMiRT) CY - Yokohama, Japan DA - 04.03.2024 KW - Reinforced Concrete KW - Drop Tower KW - Hard Impact PY - 2024 SP - 1 EP - 10 PB - IASMiRT CY - Yokohama, Japan AN - OPUS4-61915 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Munsch, Sarah Mandy A1 - Telong, Melissa A1 - Unger, Jörg F. A1 - Andrés Arcones, Daniel A1 - Pirskawetz, Stephan T1 - 63. DAfStb-Forschungskolloquium in der BAM - Themenblock 4: Digitalisierung im Bauwesen N2 - Die Digitalisierung hat sich in vielen Bereichen des Bauwesens durchgesetzt. So sind Planung und Entwurf selbst kleinerer Bauvorhaben heute vollständig digitalisiert. Auch das Monitoring von Bestandsbauwerken ist ohne digitale Datenerfassung, -verarbeitung und -speicherung nicht denkbar. Trotzdem sind Fragen hinsichtlich der strukturierten Speicherung und künftigen Nutzung von Daten noch offen. Einige Aspekte der Digitalisierung wurden im Rahmen des 63. DAfStb-Forschungskolloquiums (Tagungsband: DOI 10.26272/opus4-61338) in Vorträgen und Veröffentlichungen aufgegriffen und werden im Folgenden zusammengefasst. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Digitalisierung KW - Infrastruktur KW - Structural Health Monitoring KW - Digitaler Zwilling PY - 2025 SN - 0005-9846 VL - 75 IS - 4 SP - 136 EP - 138 PB - concrete content UG CY - Schermbeck AN - OPUS4-63070 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mendler, A. A1 - Döhler, M. A1 - Hille, Falk T1 - Detecting changes in boundary conditions based on sensitivity-based statistical tests N2 - Structural health monitoring is a promising technology to automatically detect structural changes based on permanently installed sensors. Vibration-based methods that evaluate the global system response to ambient excitation are suited to diagnose changes in boundary conditions, i.e., changes in member prestress or imposed displacements. In this paper, these changes are evaluated based on sensitivity-based statistical tests, which are capable of detecting and localizing parametric structural changes. The main contribution is the analytical calculation of sensitivity vectors for changes in boundary conditions (i.e., changes in prestress or support conditions) based on stress stiffening, and the combination with a numerically efficient algorithm, i.e., Nelson’s method. One of the main advantages of the employed damage diagnosis algorithm is that, although it uses physical models for damage detection, it considers the uncertainty in the data-driven features, which enables a reliabilitybased approach to determine the probability of detection. Moreover, the algorithm can be trained and the probability of detecting future damages can be predicted based on data and a model from the undamaged structure, in an unsupervised learning mode, making it particularly relevant for unique structures, where no data from the damaged state is available. For proof of concept, a numerical case study is presented. The study assesses the loss of prestress in a two-span reinforced concrete beam and showcases suitable validation approaches for the sensitivity calculation. T2 - International Symposium on Non-Destructive Testing in Civil Engineering (NDT-CE 2022) CY - Zurich, Switzerland DA - 16.08.2022 KW - Nelson’s method KW - Global ambient vibrations KW - Asymptotic local approach KW - Sensitivity vectors KW - Probability of detection KW - Stress stiffening PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-566632 DO - https://doi.org/10.58286/27311 SN - 1435-4934 VL - 27 IS - 9 SP - 1 EP - 13 PB - NDT.net CY - Kirchwald AN - OPUS4-56663 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiehle, Philipp T1 - Feuchteverhalten von Lehmsteinmauerwerk unter natürlichen Klimabedingungen N2 - Druckfestigkeit und Elastizitätsmodul von Lehmsteinmauerwerk nehmen mit steigendem Feuchtegehalt ab, weswegen die Mauerwerksdruckfestigkeit bei der Bemessung gemäß DIN 18940 in Abhängigkeit der maximal zu erwartenden Ausgleichsfeuchte abgemindert wird. Da bisher allerdings keine Messdaten zum Feuchtegehalt von Lehmsteinmauerwerk unter natürlichen Klimabedingungen vorliegen, stellen die normativen Grenzwerte lediglich eine konservative Abschätzung dar. Um die Feuchtegehalte von Lehmsteinmauerwerk und somit die Tragfähigkeit realitätsnah einschätzen zu können, wurden im Rahmen der vorliegenden Arbeit sowohl experimentelle als auch numerische Untersuchungen zum feuchtetechnischen Verhalten durchgeführt. Dabei wurden erstmalig magnetresonanzspektroskopische Untersuchungen an tragenden Lehmsteinen unterschiedlicher Herstellungsmethoden angewandt Weiterhin wurden Luftfeuchtesensoren in Lehmsteinmauerwerk eingebettet, um hygrische Langzeitfeuchtemessungen unter natürlichen Klimabedingungen durchzuführen. Auf Basis dieser Erkenntnisse wurde schließlich ein numerisches Modell kalibriert und Parameterstudien durchgeführt, um den unter realen Klimabedingungen tatsächlich auftretenden Feuchtegehalt im Lehmmauerwerk sowie dessen Verteilung über den Querschnitt einschätzen zu können und die normativen Grenzwerte zu überprüfen. Gezeigt wurde, dass die realitätsnahe instationäre Berechnung des Feuchtetransports mit üblichen hygrothermischen Simulationsprogrammen auf Basis einfacher feuchtetechnischer Kennwerte auch bei Lehmbaustoffen möglich ist. Der Einfluss des Quellens und Schwindens der enthaltenen Tonminerale und organischen Bestandteile wurde durch eine Modifikation bei der Ermittlung des Wasseraufnahmekoeffizienten explizit berücksichtigt und ist somit auch in den daraus abgeleiteten Transportkoeffizienten enthalten. Darüber hinaus wurde die Feuchtespeicherfunktion im überhygroskopischen Bereich auf Grundlage der Porenvolumenverteilung abgeschätzt. Die Approximation der Transportkoeffizienten und der Feuchtespeicherfunktion stellt dabei eine wesentliche Vereinfachung für Lehmbaustoffe dar, da ihre experimentelle Bestimmung aufgrund des Kontaktes mit Flüssigwasser kaum möglich ist. In Bezug auf das Feuchteverhalten üblicher Außenwandaufbauten von Wohnräumen konnte festgestellt werden, dass die Ausgleichsfeuchte im Lehmsteinmauerwerk stets unterhalb des in Nutzungsklasse 1 gemäß DIN 18940 zulässigen Grenzwertes von 65 % liegt. Je nach Putzsystem und Dämmstoff reduziert sich die Ausgleichsfeuchte auf Werte unter 60 %, wobei sich eine annähernd gleichmäßige Verteilung der Feuchte über den Mauerwerksquerschnitt hinweg einstellt. Bei Außenwänden von unbeheizten Räumen ergab sich eine maximale Ausgleichsfeuchte, die über weite Teile des Querschnitts unterhalb von 80 % lag. Der Ansatz einer maximalen Ausgleichsfeuchte von 90 % in Nutzungsklasse 2 ist folglich zu hoch angesetzt. Die zulässige Ausgleichsfeuchte bzw. der Umgebungsfeuchtefaktor in Nutzungsklasse 2 sollte dementsprechend angepasst werden. T2 - LEHM 2024 - 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Mauerwerk KW - Feuchte KW - Tragverhalten KW - Bemessung PY - 2024 AN - OPUS4-61904 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baier, Johanna T1 - Structural design of rammed earth considering the impact of moisture N2 - In March 2024, a research project was initiated at BAM with the aim of developing a design concept for rammed earth construction. It is based on experimental and numerical investigations into the mechanical load-bearing behaviour at both material and component level. As the mechanical parameters of earth building materials are strongly dependent on material moisture, the moisture behaviour of rammed earth is also being investigated in more detail. T2 - LEHM 2024 - 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Rammed earth KW - Structral design KW - Material moisture PY - 2024 AN - OPUS4-62031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Deborah T1 - Impact damage characterization at RC plates with planar tomography and FEM N2 - Prediction of dynamic effects of reinforced concrete structures under impact loading is a technical challenge. This is a consequence of the great variability of the physical properties resulting from the wide adaptability of reinforced concrete and a consequence of the wide range of impact loading. Experiments and numerical investigations are normally used on a small scale to address the problem. In this paper, impact tests on reinforced conrete plates with the lateral dimensions of 1.5 m x 1.5 m and a thickness of 30 cm are presented. In bending reinforcement, besides the velocity two properties are varied, the diameter and the spatial distribution of the rebars. Experiments are performed at the Otto-Mohr-Laboratory of the Institute of Concrete Structures of the Technische Universit¨at Dresden. Due to the accelerated fall of the impactor the velocity ranges between 20 and 70 m/s. In addition to the measured quantities such as bearing forces, accelerations are also measured at 4 different positions on and under the plate, as well as the deflection at several positions. The measured data are used for the analysis of the damage form and the numerical examinations with the program Ansys Autodyn and the material model after Drucker-Prager. Numerical investigations support the tests, with detailed analysis of individual effects. These numerical computations and the planar tomographic investigations were carried out at BAM in Berlin. With the help of planar tomographic evaluation, the damaged structure is made visible and compared with the numerical results. Influences of the bending reinforcement are explained on the basis of damage evaluation in the local area and on selected measured values. In addition to the test evaluation, the tomographic and numerical methods are presented. T2 - XI International Conference on Structural Dynamics (EURODYN 2020) CY - Online meeting DA - 23.11.2020 KW - Post-impact evaluation KW - Damage characterization KW - Planar tomography KW - Drucker-Prager KW - Ansys Autodyn PY - 2020 AN - OPUS4-51768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bartels, Jan-Hauke A1 - Gündogdu, Berk A1 - Herrmann, Ralf A1 - Marx, Steffen T1 - Beschleunigungssensoren zur Zustandsüberwachung von Ingenieurbauwerken unter Einfluss von Umweltfaktoren bei tiefen Frequenzen T1 - Acceleration sensors for structural health monitoring of engineering structures under the influence of environmental factors at low frequencies N2 - Structural Health Monitoring (SHM) wird zunehmend zur kontinuierlichen Zustandsbewertung von Ingenieurbauwerken eingesetzt. Wichtige Bewertungsparameter sind globale Systemeigenschaften, wie z. B. Eigenfrequenzen, zu deren Bestimmung Beschleunigungssensoren eingesetzt werden. Häufig werden sog. MEMS-Sensoren (Micro Electro Mechanical Systems) verwendet, die jedoch ein hohes Rauschniveau aufweisen. Alternativ können rauschärmere IEPE-Sensoren (Integrated Electronics Piezo Electric) eingesetzt werden, die auch bei geringster Strukturanregung Schwingungen zuverlässig erfassen. Ferner besteht das Problem, dass Änderungen der Eigenfrequenzen infolge Bauwerksschädigung schwer von Änderungen der Eigenfrequenzen infolge Umwelteinflüssen zu unterscheiden sind. Letztere verändern die Eigenschaften der Struktur und die des Messsystems. Um Umwelteinflüsse auf das Messsystem im Anwendungsgebiet Ingenieurbau zu untersuchen, wurden IEPE-Beschleunigungsaufnehmer hinsichtlich ihres Übertragungsverhaltens im niederfrequenten Beschleunigungsbereich analysiert. Es zeigt sich, dass das Verhalten nicht nur frequenz-, sondern auch temperaturabhängig ist, während die Luftfeuchte keinen Einfluss hat. Diese für das Bauwerk unbedenklichen Einflüsse müssen für eine robuste Zustandsüberwachung kompensiert werden. Für die Anwendung im Ingenieurbau werden IEPE-Sensoren empfohlen, da sie ein hohes Signal-zu-Rausch-Verhältnis aufweisen und niederfrequente Bauwerksschwingungen zuverlässig erfassen. N2 - Acceleration sensors for structural health monitoring of engineering structures under the influence of environmental factors at low frequencies. Structural health monitoring (SHM) is increasingly used to continuously assess the condition of engineering structures. Important assessment parameters are global system properties, such as eigenfrequency, which are measured by accelerometers. Micro-electro-mechanical systems (MEMS) sensors are often used, but have a high noise level. Alternatively, low-noise IEPE (integrated electronics piezo electric) sensors can be used, which reliably detect vibrations even with the slightest structural excitation. Another problem is that changes in eigenfrequency due to structural damage are difficult to distinguish from changes in eigenfrequency due to environmental effects. The latter change the properties of both the structure and the measurement system. In order to investigate environmental effects on the measurement system in the field of civil engineering, IEPE accelerometers have been analyzed for their transmission behavior in the low-frequency acceleration range. It was found that the behavior is not only frequency dependent, but also temperature dependent, while humidity has no influence. These nonstructural effects must be compensated for to ensure robust condition monitoring. IEPE sensors are recommended for civil engineering applications because of their high signal-to-noise ratio and ability to reliably detect low-frequency structural vibrations. KW - Beschleunigungssensoren KW - Kalibrierung KW - Structural Health Monitoring KW - Umwelteinflüsse KW - Übertragungsverhalten KW - acceleration sensors KW - calibration KW - environmental influences KW - transmission behavior PY - 2024 DO - https://doi.org/10.1002/bate.202300056 SN - 1437-0999 SN - 0932-8351 VL - 101 IS - 10 SP - 1 EP - 11 PB - Ernst & Sohn CY - Berlin AN - OPUS4-60772 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Makris, Ralf ED - Aign, J. T1 - Reinforcement bar and reinforcement bar splicing systems under impact loading – Experimental tests and test specification N2 - Reinforced concrete is a widely used material for power generation structures, where load scenarios like impact loadings need to be considered. In this context mechanical splicing systems for the connection of reinforcement bars are of specific interest and impact resistance for the splicing systems has to be verified. High speed tensile tests need to be performed on splicing systems for reinforcement bars to confirm the capability of the coupler to resist impact loading. Furthermore, the ability of the reinforcement steel to dissipate energy by ductile behaviour with pronounced plastic strains should be confirmed by these tests. During the last decades comprehensive experiences were developed at BAM performing high speed tensile tests on reinforcement bars as well as on several splicing systems. For the lack of available standards defining these tests in detail an appropriate test procedure was developed and continuously optimized during this period at BAM. The test procedure is partially based on testing principles adapted from available standards. The main intention behind this test procedure is to perform high-speed tensile tests with a specific constant strain rate generated at the specimen. Furthermore, main objective was to establish a procedure to guarantee the comparability of test results for different diameter of reinforcement as well as for different types of couplers. Besides the pure execution of the high-speed tensile tests, the test specification also declares how to evaluate the measurements and the test results. Finally, some typical results will be presented in this contribution. T2 - SMIRT 26 CY - Potsdam, Germany DA - 10.07.2022 KW - Impact KW - Coupler systems KW - High-speed KW - Reinforcement PY - 2022 SP - 1 EP - 10 AN - OPUS4-55422 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pirskawetz, Stephan A1 - Bösche, Thomas A1 - Carstens, Ole A1 - Hille, Falk A1 - Holst, Ralph A1 - Käding, Max A1 - Kaplan, Felix A1 - Löhr, Manuel A1 - Richter, Walter A1 - Saloga, Katrin A1 - Schmidt, Sebastian A1 - Sodeikat, Christian A1 - Thenikl, Thomas T1 - Detektion von Spanndrahtbrüchen mit Schallemissionsanalyse N2 - Dieses Dokument beschreibt das Verfahren Schallemissionsanalyse zur Detektion von Spanndrahtbrüchen in Spannbetonbrücken im Rahmen einer kontinuierlichen Überwachung. Die Überwachung mit Schallemission liefert eine Aussage über die Anzahl von Spanndrahtbrüchen innerhalb des Überwachungszeitraumes und innerhalb der Reichweite der installierten Sensoren. Mit dem Verfahren können die Spanndrahtbrüche lokalisiert werden. Auf Basis einer weitgehend automatisierten Datenanalyse stehen Informationen über Drahtbrüche kurzfristig nach dem Ereignis zur Verfügung. Der Anwendungsbereich des Dokuments umfasst Brücken- und Ingenieurbauwerke mit Spanndrähten mit sofortigem oder nachträglichem Verbund. Spannsysteme ohne Verbund fallen nicht in den Anwendungsbereich. Die beschriebenen Verfahren können auf Spannsysteme ohne Verbund übertragen werden. Mit dem Verfahren Schallemissionsanalyse ist es nicht möglich, Spanndrahtbrüche zu finden, die vor dem Beginn der Überwachung entstanden sind. Das Dokument richtet sich an Baulastträger, Anbieter und Betreiber von Monitoringsystemen auf Basis der Schallemissionsanalyse sowie Ingenieurbüros, welche die Ergebnisse der Überwachung bewerten und Maßnahmen daraus ableiten. Es gibt Hinweise zur Planung, Ausschreibung, Installation und zum Betrieb von Monitoringsystemen zur Detektion von Spanndrahtbrüchen mit Schallemission sowie zur Überprüfung der Funktion installierter Systeme. Zur Funktionskontrolle werden Signale mit der Referenzquelle am Bauwerk ausgelöst. Diese Signale sind zu detektieren, innerhalb der vorgegebenen Genauigkeit zu lokalisieren und die vorgegebene Alarmkette muss angestoßen werden. KW - Schallemission KW - Brücke KW - Spannbeton KW - Spannstahlbruch PY - 2024 SN - 978-3-947971-34-3 VL - Richtlinie SE 05 SP - 1 EP - 33 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin ET - Ausgabe Mai 2024 AN - OPUS4-60679 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thibaux, Philippe A1 - Thiele, Marc A1 - Van Wittenberghe, Jeroen A1 - Baeßler, Matthias T1 - Comparison of resonance and hydraulic testing on large scale fatigue tests of welded tubular joints for offshore wind turbine foundations N2 - Jackets structures as foundations for offshore wind energy converters are efficient solutions. But these structures require the welding of a large number of joints. The design of the Jacket structures is typically driven by fatigue. Therefore, consequently the fatigue strength of the joints is a primary parameter for an optimized design. The present paper investigates if tubular joints produced by manual welding using the current techniques have an improved performance compared to the relevant standards that are applied for the design of the foundations. To investigate this, 4 full-scale tests in geometry representative of a structure were performed, 2 using a resonance method and 2 using a three-point bending method with hydraulic actuators. The results are similar, with cracks initiated early and extending extensively before failure. The results are very close to the current T-curve from DNV RP-C203 applied for tubular joints. KW - Fatigue KW - Tubular joints KW - Resonance testing KW - Steel welds PY - 2025 DO - https://doi.org/10.1016/j.ijfatigue.2024.108797 SN - 0142-1123 VL - 193 SP - 1 EP - 16 PB - Elsevier Ltd. AN - OPUS4-62373 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ratkovac, Mirjana T1 - Perspectives on Wind and Wave Load Reconstruction from SHM Data for Offshore Wind Turbines N2 - As many wind turbines approach the end of their design lifetime, from a technical point of view, comprehensive fatigue analysis of all critical parts is necessary to decide what comes after – continued operation, repowering, or decommissioning. Typically, it is a two-stage evaluation process consisting of a physical inspection of the structure and an analytical part to compare the design and actually experienced loading conditions. Structural health monitoring helps to reduce the uncertainties in the estimations by providing insight into deviations between the designed and the built structure. Furthermore, it allows the evaluation of the consumed fatigue lifetime by analyzing the strain measurements that mirror the actual structural response to experienced environmental and operational conditions. However, the measurement values are limited to a sparse number of instrumented spots on the structure, and further extrapolation to the non-instrumented (critical) sections is required to perform a complete fatigue assessment. One known approach is the external force reconstruction, which has only scarcely been considered for application in offshore wind turbines. In order to extend the previously developed thrust force reconstruction framework, this work discusses the possibilities and challenges of wind and wave loading reconstruction in offshore wind turbine support structures. T2 - 4th International Conference on Health Monitoring of Civil & Maritime Structures (HeaMES 2023) CY - Online meeting DA - 12.06.2023 KW - Wind turbines KW - Force reconstruction KW - Structural Health Monitoring PY - 2023 AN - OPUS4-57687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schepers, Winfried A1 - Brinkgreve, Ronald B. J. A1 - Holtzendorff, Kira A1 - Wegener, Dirk A1 - Appel, Silke A1 - Efthymiou, Georgia A1 - Krajewski, Wolfgang A1 - Machaček, Jan A1 - Meier, Thomas A1 - Nseir, Bashar A1 - Rangelow, Peter A1 - Schmitt, Jürgen A1 - Staubach, Patrick A1 - Vrettos, Christos T1 - Numerische Ermittlung von Baugrundschwingungen bei dynamisch belasteten Fundamenten: Empfehlungen zur Modellierung T1 - Numerical analysis of soil vibrations due to vibrating foundations: Guidance for model design N2 - AbstractIn der Praxis tätige geotechnisch Planende kommen in zunehmendem Maße mit dynamischen Fragestellungen in Berührung. Hersteller von geotechnischer Berechnungssoftware haben entsprechend ihre ursprünglich für statische Aufgabenstellungen konzipierten Produkte um die Möglichkeit zur Lösung von Wellenausbreitungsproblemen im Baugrund erweitert. Den Anwendern fehlt aber häufig die notwendige Erfahrung zur Durchführung dieser Art von numerischen Berechnungen. Die Arbeitskreise 1.4 „Baugrunddynamik“ und 1.6 „Numerik in der Geotechnik“ der Deutschen Gesellschaft für Geotechnik (DGGT) haben diese Entwicklung aufgegriffen und einen gemeinsamen Unterarbeitskreis „Numerik in der Baugrunddynamik“ gegründet. Der vorliegende Beitrag stellt die aktuellen Ergebnisse der Arbeit des Unterarbeitskreises vor und fasst die gewonnenen Erkenntnisse in Form von Empfehlungen zusammen. N2 - Geotechnical engineers are increasingly concerned with wave propagation problems. Manufacturers of geotechnical analysis software added features for soil dynamic analyses to their products initially devised for static geotechnical analyses. Though, users often lack the experience for conducting such advanced numerical analyses. Working groups 1.4 "Soil dynamics" and 1.6 "Numerical analyses in geotechnical engineering" of DGGT German Society for Geotechnical Engineering established a joint subgroup "Numerical analyses in soil dynamics" to address this shortcoming. The present paper presents the work of the subgroup so far and provides some guidance on conducting numerical analyses in soil dynamics. KW - Wellenausbreitung KW - Numerische Methoden KW - Empfehlungen KW - Modellgröße KW - Zeitschrittweite PY - 2024 DO - https://doi.org/10.1002/gete.202400016 SN - 0172-6145 VL - 47 IS - 4 SP - 254 EP - 268 PB - Ernst CY - Berlin AN - OPUS4-62078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Ronald A1 - Simon, Patrick A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Baeßler, Matthias T1 - Bestandteile Digitaler Zwillinge im Erhaltungsmanagement von Verkehrsbrücken T1 - Components of digital twins in the operation and maintenance management of traffic bridges N2 - Digitale Zwillinge werden zukünftig ein integraler Bestandteil des Erhaltungsmanagements von Verkehrsbrücken sein. In diesem Beitrag wird argumentiert, dass sie nicht nur als digitale Abbilder physikalischer Bauwerke verstanden werden sollten, sondern als eine umfassende digitale Methode, die durch die Integration von Datenerfassung, Erhaltungsmaßnahmen, Datenmanagement, Bauwerksbewertung und Entscheidungsunterstützung die Bauwerksüberwachung und ‐erhaltung verbessert. In diesem Zusammenhang wird betont, dass der Übergang von der reaktiven zur prädiktiven Erhaltung durch den Einsatz von Digitalen Zwillingen nur dann realisierbar ist, wenn neben den erforderlichen diagnostischen und prognostischen Zustandsanalysen auch Methoden zur Optimierung von Entscheidungen über Datenerfassung und Erhaltungsmaßnahmen implementiert werden. Zur Veranschaulichung der Diskussion werden in diesem Beitrag exemplarisch zwei Bestandteile eines Digitalen Zwillings für das Erhaltungsmanagement von Verkehrsbrücken am Beispiel einer Eisenbahnbrücke demonstriert. Dabei wird zum einen gezeigt, wie Monitoringdaten mittels eines Datenmanagementsystems strukturiert verwaltet und für angeknüpfte Analysen bereitgestellt werden. Zum anderen erfolgt im Rahmen einer bauwerksspezifischen Einwirkungsermittlung eine Zugidentifikation anhand von gemessenen Schwellenschwingungen. N2 - Digital twins will become an integral part of the operation and maintenance management of traffic bridges in the future. This paper argues that they should not only be understood as digital representations of physical structures but as a digital methodology that enhances the operation and maintenance of bridges through the integration of data collection, maintenance actions, data management, structural assessment, and decision support. In this context, it is emphasized that the transition from reactive to predictive maintenance using digital twins can only be achieved if, in addition to the necessary diagnostic and prognostic condition analyses, methods for optimizing decisions on data collection and maintenance actions are also implemented. To illustrate this discussion, two key components of a digital twin for the operation and maintenance management of traffic bridges are demonstrated using a railway bridge as an example. First, it is shown how monitoring data can be systematically managed and made available for subsequent analyses through a data management system. Second, train identification based on measured sleeper vibrations is conducted as part of an object-specific load assessment. KW - Digitale Zwillinge KW - Erhaltung KW - Inspektion KW - Monitoring KW - Brücken PY - 2025 DO - https://doi.org/10.1002/bate.202400101 SN - 1437-0999 SP - 1 EP - 11 PB - Ernst & Sohn CY - Berlin AN - OPUS4-62837 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Patrick A1 - Helmrich, M. A1 - Herrmann, Ralf A1 - Schneider, Ronald A1 - Baeßler, Matthias A1 - Lorelli, S. A1 - Morgenthal, G. T1 - Maintalbrücke Gemünden: Bauwerksmonitoring und -identifikation aus einem Guss T1 - Maintalbrücke Gemünden – Integrated structural health monitoring and UAS diagnostics N2 - Die Infrastruktursysteme der Industriestaaten erfordern heute und in Zukunft ein effizientes Management bei alternder Bausubstanz, steigenden Lasten und gleichbleibend hohem Sicherheitsniveau. Digitale Technologien bieten ein großes Potenzial zur Bewältigung der aktuellen und künftigen Herausforderungen im Infrastrukturmanagement. Im BMBF-geförderten Projekt Bewertung alternder Infrastrukturbauwerke mit digitalen Technologien (AISTEC) wird untersucht, wie unterschiedliche Technologien und deren Verknüpfung gewinnbringend eingesetzt werden können. Am Beispiel der Maintalbrücke Gemünden werden ein sensorbasiertes Bauwerksmonitoring, bildbasierte Inspektion mit durch Kameras ausgestatteten Drohnen (UAS) und die Verknüpfung digitaler Bauwerksmodelle umgesetzt. Die aufgenommenen Bilder dienen u. a. als Grundlage für spätere visuelle Anomaliedetektionen und eine 3D-Rekonstruktion, welche wiederum für die Kalibrierung und Aktualisierung digitaler Tragwerksmodelle genutzt werden. Kontinuierlich erfasste Sensordaten werden ebenfalls zur Kalibrierung und Aktualisierung der Tragwerksmodelle herangezogen. Diese Modelle werden als Grundlage für Anomaliedetektionen und perspektivisch zur Umsetzung von Konzepten der prädiktiven Instandhaltung verwendet. Belastungsfahrten und historische Daten dienen in diesem Beitrag der Validierung von kalibrierten Tragwerksmodellen. N2 - Infrastructure systems of industrialised countries today and in the future require efficient management with an ageing stock, increasing loads while simultaneously maintaining a high level of safety. Digital technologies offer great potential for the current and future challenges in infrastructure management. The BMBF-funded project AISTEC is investigating how the individual technologies and their interconnection can be used beneficially. With the Maintalbrücke in Gemünden as an exemplary application, sensor-based structural monitoring, image-based inspection using unmanned aircraft systems (UAS) equipped with cameras and the integration of digital structural models are being implemented. The recorded images serve, among others, as basis for subsequent anomaly detection and a 3D reconstruction, which in turn are used for updating digital structural models. Continuously recorded sensor data is used to update the parameters of the structural models, which in turn provide the basis for predictive maintenance. Load tests are used to validate the models. KW - Bauwerksüberwachung KW - Strukturmonitoring KW - Structural Health Monitoring KW - Modell-Update KW - UAS KW - Belastungstest KW - Structural system identification KW - Structural health monitoring KW - Model update KW - UAS KW - Load tests PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-554924 DO - https://doi.org/10.1002/bate.202100102 SN - 0932-8351 VL - 99 IS - 3 SP - 163 EP - 172 PB - Ernst & Sohn CY - Berlin AN - OPUS4-55492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schneider, Ronald A1 - Simon, Patrick A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Baeßler, Matthias T1 - Vibration-based system identification of a large steel box girder bridge N2 - The Bundesanstalt für Materialforschung und -prüfung (BAM) collaborates with TNO to develop a software framework for automated calibration of structural models based on monitoring data. The ultimate goal is to include such models in the asset management process of engineering structures. As a basis for developing the framework, a multi-span road bridge consisting of ten simply supported steel box girders was selected as a test case. Our group measured output-only vibration data from one box girder under ambient conditions. From the data, we determined eigenfrequencies and mode shapes. In parallel, we developed a preliminary structural model of the box girder for the purpose of predicting its modal properties. In this contribution, we provide an overview of the measurement campaign, the operational modal analysis, the structural modeling and qualitatively compare the identified with the predicted modes. As an outlook, we discuss the further steps in the calibration process and future applications of the calibrated model. T2 - XII International Conference on Structural Dynamics (EURODYN 2023) CY - Delft, The Netherlands DA - 02.07.2023 KW - Verkehrsinfrastukturen KW - SHM KW - Model updating KW - System identification KW - Operational modal analysis PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-605041 DO - https://doi.org/10.1088/1742-6596/2647/18/182039 SN - 1742-6596 VL - 2647 IS - 18 SP - 1 EP - 9 PB - IOP Publishing CY - Bristol AN - OPUS4-60504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fiedler, Georg A1 - Hering, Marcus A1 - Schubert, T. A1 - Bracklow, F. A1 - Nerger, Deborah A1 - Hille, Falk A1 - Beckmann, B. ED - Wuttke, F. ED - Aji, H. ED - Özarmut, A. T1 - Schädigung von Stahlbetonplatten infolge eines harten Anpralls - Vergleich von halb-empirischen Methoden und experimentellen Ergebnissen N2 - Schutzbauwerke von systemkritischen Infrastruktureinrichtungen wie Betonwände und Betonbarrieren müssen Anprallereignissen oder schweren Unfällen in einem vertretbaren Maße widerstehen können. Anprallereignisse können verschiedenster Natur sein. Hierzu zählen Steinschlag, Fahrzeug- oder Flugzeuganprall oder auch Geschosseinschlag. Geschosseinschläge bzw. Bei den Anprall- oder Impaktereignissen wird zwischen hartem und weichem Anprall unterschieden, bei hartem Anprall verformt sich der Anprallkörper nicht oder nur geringfügig, bei weichem Anprall stark. In diesem Artikel werden Forschungsergebnisse zum harten Anprall auf bewehrte Stahlbetonplatten vorgestellt, welche über die letzten Jahre im Rahmen eines Kooperationsprojekts zwischen dem Institut für Massivbau (IMB) der Technischen Universität Dresden (TUD) und der Bundesanstalt für Materialforschung und -prüfung (BAM) durchgeführt wurden. Auf dem Gelände des Otto-Mohr-Labors (OML) der TUD steht hierfür ein speziell konzipierter Fallturm zur Verfügung. Der Aufbau im Fallturm lässt aktuell druckluftbeschleunigte Impaktversuche mit mittleren Anprallgeschwindigkeiten zu. Die durch Anprall geschädigten Stahlbetonplatten wurden anschließend bei der BAM mit Strahlung tomographisch untersucht. Diese Untersuchungen ermöglichen einen Blick auf die Schädigung und Rissstruktur im Inneren der Stahlbetonplatten. Ein Schwerpunkt der durchgeführten Untersuchung ist der Vergleich von Testergebnissen mit den häufig angewendeten halbempirischen Berechnungsmethoden zu den erforderlichen Wandstärken und den sich daraus ergebenden zulässigen Anprallgeschwindigkeiten. Bei diesem Vorgehen wird auch die mit analytischen Methoden abschätzbare Durchdringungsgeschwindigkeit bzw. Austrittgeschwindigkeit eines Projektils ermittelt und mit den realen Testergebnissen verglichen. Außerdem wird der Einfluss von sowohl externen als auch internen Strukturparametern auf Risse betrachtet und ein Fazit abgeleitet. Weiterhin werden laufende und zukünftige wissenschaftliche Untersuchungen zum Anprall auf Betonstrukturen am IMB und der BAM genannt. T2 - 18. D-A-CH-Tagung CY - Kiel, Germany DA - 13.09.2023 KW - Impakt KW - Harter Anprall an Stahlbetonstrukturen KW - Fallturm PY - 2023 SN - 978-3-930108-15-1 SP - 471 EP - 479 PB - Deutsche Gesellschaft für Erdbebeningenieurwesen und Baudynamik (DGEB) e.V. AN - OPUS4-58341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc T1 - Detection and monitoring of the fatigue crack growth on welds – Application-oriented use of NDT methods N2 - Early detection of fatigue cracks and accurate measurements of the crack growth play an important role in the maintenance and repair strategies of steel structures exposed to cyclic loads during their service life. Observation of welded connections is especially of high relevance due to their higher susceptibility to fatigue damage. The aim of this contribution was to monitor fatigue crack growth in thick welded specimens during fatigue tests as holistically as possible, by implementing multiple NDT methods simultaneously in order to record the crack initiation and propagation until the final fracture. In addition to well-known methods such as strain gauges, thermography, and ultrasound, the crack luminescence method developed at the Bundesanstalt für Materialforschung und -prüfung (BAM), which makes cracks on the surface particularly visible, was also used. For data acquisition, a first data fusion concept was developed and applied in order to synchronize the data of the different methods and to evaluate them to a large extent automatically. The resulting database can ultimately also be used to access, view, and analyze the experimental data for various NDT methods. During the conducted fatigue tests, the simultaneous measurements of the same cracking process enabled a comprehensive comparison of the methods, highlighting their individual strengths and limitations. More importantly, they showed how a synergetic combination of different NDT methods can be beneficial for implementation in large-scale fatigue testing but also in monitoring and inspection programs of in-service structures - such as the support structures of offshore wind turbines. T2 - Fatigue Design 2023 CY - Senlis, France DA - 29.11.2023 KW - Crack growth KW - Fatigue KW - NDT KW - Welded PY - 2023 AN - OPUS4-62374 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Digitaler Zwilling im Erhaltungsmanagement von Straßenbrücken N2 - Digitale Zwillinge werden zukünftig ein integraler Bestandteil des Erhaltungsmanagements von Straßenbrücken sein. In diesem Beitrag wird argumentiert, dass sie nicht nur als digitale Abbilder physikalischer Bauwerke verstanden werden sollten, sondern als eine umfassende digitale Methode, die durch die Integration von Datenerfassung, Erhaltungsmaßnahmen, Datenmanagement, Bauwerksbewertung und Entscheidungsunterstützung die Bauwerksüberwachung und -erhaltung verbessert. In diesem Zusammenhang wird betont, dass der Übergang von der reaktiven zur prädiktiven Erhaltung durch den Einsatz von Digitalen Zwillingen nur dann realisierbar ist, wenn neben den erforderlichen diagnostischen und prognostischen Zustandsanalysen auch Methoden zur Optimierung von Entscheidungen über Datenerfassung und Erhaltungsmaßnahmen implementiert werden. Zur Veranschaulichung der Diskussion werden in diesem Beitrag exemplarisch zwei Bestandteile eines Digitalen Zwillings für das Erhaltungsmanagement von Verkehrsbrücken am Beispiel einer Eisenbahnbrücke demonstriert. Dabei wird zum einen gezeigt, wie Monitoringdaten mittels eines Datenmanagementsystems strukturiert verwaltet und für angeknüpfte Analysen bereitgestellt werden. Zum anderen erfolgt im Rahmen einer bauwerksspezifischen Einwirkungsermittlung eine Zugidentifikation anhand von gemessenen Schwellenschwingungen T2 - Workshop „Digitaler Zwilling im Lebenszyklusmanagement" der AG BIM in der Bauwerkserhaltung des Koordinierungsausschusses Erhaltung (KoA-Erhaltung) der B/L-DB Konstruktiver Ingenieurbau CY - Potsdam, Germany DA - 09.04.2025 KW - Digitale Zwillinge KW - Erhaltung KW - Inspektion KW - Monitoring KW - Brücken PY - 2025 AN - OPUS4-62951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hille, Falk A1 - Sowietzki, D. A1 - Makris, R. T1 - Luminescence-based early detection of fatigue cracks N2 - Classic non-destructive fatigue crack detection methods reveal the state of the fatigue damage evolution at the moment of application, generally not under operational conditions. The here introduced crack luminescence method realizes a clear visibility of the occurred and growing crack in loaded components during operation. Different established experiments show that due to the sensitive coating a crack Formation can be detected even in early stage under the premise the crack reached the surface. The coating consists of two layers with different properties and functions. The bottom layer emits light as fluorescence under UV radiation. The top layer covers the fluorescing one and prevents the emitting of light in case of no damage at the surface. In case of surface crack occurrence, the luminescent light is clearly noticeable by visual observations and also by standard camera equipment which makes automated crack detection possible as well. It is expected that crack luminescence can increase structural safety as well as reduce costs and time for inspections and preventive maintenance. KW - Coating KW - Fatigue KW - Crack damage detection KW - Luminescence PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-510517 DO - https://doi.org/10.1016/j.matpr.2020.02.338 SN - 2214-7853 SP - 1 EP - 5 PB - Elsevier CY - Amsterdam AN - OPUS4-51051 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk T1 - Developing a guideline for SHM of road bridges in Germany N2 - In recent years, Structural Health Monitoring (SHM) has become a useful and increasingly widely used tool for supporting lifetime extensions of existing bridges with known structural deficiencies or indications of potentially critical damages or damage processes. At the same time, methods and tools are emerging, which enable monitoring-informed predictive maintenance of new and existing bridges based on digital twins. The monitoring process – starting from the definition of monitoring actions and ending with decisions based on monitoring outcomes – is complex and requires expertise in structural engineering, operation and maintenance of bridges, metrology, and data analytics. To support German road authorities, engineering consultancies, building contractors and other stakeholders of the bridge management, the Federal Highway Research Institute (BASt) has initiated the development of a new guideline for applying SHM as part of the management of road bridges. The guideline will present various use cases and for each identified use case, it will propose a proven monitoring scheme. In addition, the guideline will provide guidance on assessing the benefits of SHM as well as a common approach to managing monitoring data as a systematic basis for integrating monitoring data in the bridge management. This contribution discusses the motivation, objectives, and scope of the guideline, describes its use case centric structure and outlines the proposed data management. T2 - IABMAS 2024 CY - Kopenhagen, Danmark DA - 24.06.2024 KW - Guideline KW - Infrastructure KW - Structural health monitoring KW - Road bridges PY - 2024 AN - OPUS4-61395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Patrick A1 - Schneider, Ronald A1 - Baeßler, Matthias A1 - Morgenthal, Guido ED - Cha, Young-Jin T1 - A Bayesian Probabilistic Framework for Building Models for Structural Health Monitoring of Structures Subject to Environmental Variability N2 - Managing aging engineering structures requires damage identification, capacity reassessment, and prediction of remaining service life. Data from structural health monitoring (SHM) systems can be utilized to detect and characterize potential damage. However, environmental and operational variations impair the identification of damages from SHM data. Motivated by this, we introduce a Bayesian probabilistic framework for building models and identifying damage in monitored structures subject to environmental variability. The novelty of our work lies (a) in explicitly considering the effect of environmental influences and potential structural damages in the modeling to enable more accurate damage identification and (b) in proposing a methodological workflow for model‐based structural health monitoring that leverages model class selection for model building and damage identification. The framework is applied to a progressively damaged reinforced concrete beam subject to temperature variations in a climate chamber. Based on deflections and inclinations measured during diagnostic load tests of the undamaged structure, the most appropriate modeling approach for describing the temperature‐dependent behavior of the undamaged beam is identified. In the damaged state, damage is characterized based on the identified model parameters. The location and extent of the identified damage are consistent with the cracks observed in the laboratory. A numerical study with synthetic data is used to validate the parameter identification. The known true parameters lie within the 90% highest density intervals of the posterior distributions of the model parameters, suggesting that this approach is reliable for parameter identification. Our results indicate that the proposed framework can answer the question of damage identification under environmental variations. These findings show a way forward in integrating SHM data into the management of infrastructures. KW - Verkehrsinfrastukturen KW - SHM KW - Model Updating KW - Environmental and Operational Variability KW - Damage Identification KW - Model Building PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-605027 DO - https://doi.org/10.1155/2024/4204316 SN - 1545-2255 VL - 2024 IS - 1 SP - 1 EP - 23 PB - Wiley AN - OPUS4-60502 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baeßler, Matthias A1 - Simon, Patrick T1 - Ballasted track on vibrating bridge decks: physical mechanisms, empirical findings, and a proposal for assessment N2 - This paper summarizes the key findings and physical mechanisms and provides information on open questions and the assessment of railway bridge superstructure vibrations. Bridges are classic disruption points on a railway track. If bridge superstructures are dynamically excited by train traffic, the vertical accelerations of the track must be considered. For a ballasted track, this can lead to the destabilization of the ballast track, as the bridge superstructure acts like a vibrating table. In this respect, the paper explains in more detail what is meant by destabilization, when this destabilization occurs and how various influencing parameters such as acceleration amplitude, the vibration sequence and frequency affect its occurrence. In the InBridge4EU project, gaps in knowledge such as the effect of single impulse loads are being investigated experimentally. A new test facility has been set up for this purpose, the initial results of which are presented here. An essential element in the assessment of this scenario is the stability of the track under high compression forces with simultaneous dynamic excitation of the superstructure. A new approach for the assessment of bridge vibrations with respect to lateral stability is presented. KW - Railway bridge dynamics KW - Bridge deck acceleration KW - Ballast destabilization KW - Lateral track stability KW - Track buckling PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630972 DO - https://doi.org/10.1142/S0219455425400243 SN - 0219-4554 SN - 1793-6764 IS - 2540024 SP - 1 EP - 27 PB - World Scientific CY - Singapore AN - OPUS4-63097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herrmann, Ralf A1 - Ramasetti, Eshwar Kumar A1 - Degener, Sebastian A1 - Hille, Falk A1 - Baeßler, Matthias T1 - A living lab for Structural Health Monitoring at the Nibelungen Bridge Worms for Transfer Learning of Structural Dynamics N2 - The Nibelungen Bridge in Worms, Germany has been selected as a national demonstration structure for advanced non-destructive testing (NDT) and structural health monitoring concepts to extend the lifetime of civil structures and to optimize O&M actions. Parts of the research that involves this bridge as a demonstrator belong to the focus area program SPP100+. In this program, the bridges SHM System has been extended and combined with an additional setup of vibration sensors. The used digital smart sensor with pre-processing functions, the arrangement of the sensors at the structure and additional edge computing capability allows the investigation of transfer learning and other methods directly into the real structure. The living lab with seven triaxial accelerometers can be reconfigured in real-time and adjusted to the needs of AI models for classification. The comparison with the existing conventional SHM sensors has been made possible by hardware synchronization to the existing SHM System and collocating sensors at similar positions, so that a hardware exchange can be an investigated use-case for the transfer learning. During idle times, the system collects vibration data like a conventional SHM system. T2 - 10th European Workshop on Structural Health Monitoring (EWSHM 2024) CY - Potsdam DA - 10.06.2024 KW - Nibelungen Bridge KW - Living Lab KW - Transfer Learning KW - Transfer Structures KW - Modal Analysis PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612810 UR - https://www.ndt.net/search/docs.php3?id=29853 DO - https://doi.org/10.58286/29853 SN - 1435-4934 VL - 29 IS - 7 SP - 1 EP - 8 PB - NDT.net GmbH & Co. KG CY - Mayen AN - OPUS4-61281 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick A1 - Baeßler, Matthias ED - Rogge, Andreas ED - Meng, Birgit T1 - Temperatureinfluss auf Strukturmonitoring – Aktuelle Versuche N2 - Strukturmonitoring kann wertvolle Daten für die Zustandsbewertung und Schadensdetektion von Infrastrukturbauwerken liefern. Umgebungsbedingungen wie die Temperatur beeinflussen die Bauwerke und somit die Messdaten jedoch erheblich. Um Methoden für den Umgang mit Temperatureinflüssen zu entwickeln, wurden an der BAM Versuche an Stahlbeton- und Asphaltbalken unter kontrollierten Temperaturen von -40 °C bis 60 °C und definierten Schädigungen durchgeführt. Die Daten ermöglichen die Erforschung und Validierung neuer, auch unter Temperatureinfluss zuverlässiger Methoden des Strukturmonitorings. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Strukturmonitoring KW - Temperatureinfluss KW - Infrastrukturbauwerke KW - Stahlbeton- und Asphaltbalken PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613289 SN - 978-3-9818564-7-7 SP - 294 EP - 302 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ramasetti, Eshwar Kumar A1 - Herrmann, Ralf A1 - Degener, Sebastian A1 - Baeßler, Matthias T1 - Development of generic AI models to predict the movement of vehicles on bridges N2 - For civil, mechanical, and aerospace structures to extend operation times and to remain in service, structural health monitoring (SHM) is vital. SHM is a method to examining and monitoring the dynamic behavior of essential constructions. Because of its versatility in detecting unfavorable structural changes and enhancing structural dependability and life cycle management, it has been extensively used in many engineering domains, especially in civil bridges. Due to the recent technical developments in sensors, high-speed internet, and cloud computing, data-driven approaches to structural health monitoring are gaining appeal. Since artificial intelligence (AI), especially in SHM, was introduced into civil engineering, these modern and promising methods have attracted significant research attention. In this work, a large dataset of acceleration time series using digital sensors was collected by installing a structural health monitoring (SHM) system on Nibelungen Bridge located in Worms, Germany. In this paper, a deep learning model is developed for accurate classification of different types of vehicle movement on the bridge from the data obtained from accelerometers. The neural network is trained with key features extracted from the acceleration dataset and classification accuracy of 98 % was achieved. KW - Structural Health Monitoring KW - Artifical Intelligence KW - Machine Learning KW - Nibelungen Bridge PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-620289 DO - https://doi.org/10.1016/j.prostr.2024.09.307 VL - 64 SP - 557 EP - 564 PB - Elsevier B.V. AN - OPUS4-62028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf T1 - Managing Structural Health Monitoring with the Research Data Management Platform BAM Data Store N2 - Structural Health Monitoring (SHM) is an interdisciplinary challenge involving the assessment and prediction of the condition of civil structures, such as bridges, based on measurements and models. This presentation provides insight into how the BAM Data Store is used to represent a SHM project including the metadata and the monitoring data, itself. It describes the structure of the core elements of a typical SHM and introduces metadata profiles. This enables linking objects within the BAM Data Store to create a hierarchical structure. N2 - Structural Health Monitoring (SHM) ist eine interdisziplinäre Aufgabe bei der es um die Bewertung und Zustandsprognose von Bauwerken, wie z. B. Brücken, auf der Grundlage von Messungen und Modellen geht. Die Präsentation gibt einen Einblick in die Verwendung des BAM Data Stores zur Abbildung eines SHM Projekts zum Datenmanagement aller relevanten Metadaten und der Monitoringdaten selbst. Es werden die Struktur der Kernelemente eines typischen SHM beschrieben und Metadatenprofile für diese vorgestellt. Im BAM Data Store werden damit die strukturierte Verknüpfung von Objekten ermöglicht, um eine hierarchische Struktur zu erzeugen. T2 - Data Store Days 2025 CY - Berlin, Germany DA - 09.04.2025 KW - Structural Health Monitoring (SHM) KW - BAM Data Store KW - Verkehrsinfrastrukturen PY - 2025 AN - OPUS4-62942 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - SysPark: a software tool for system-wide adaptive planning of inspections of turbine support structures in offshore wind farms N2 - Fatigue is one of the main deterioration processes affecting the performance of welded steel support structures of wind turbines in offshore wind farms. In this contribution, we present a probabilistic physics-based fatigue deterioration model of a wind farm that accounts for the stochastic dependence among the fatigue behavior of different hotspots at turbine and wind farm level. The dependence exists because of uncertain common influencing factors such as similar material properties, fabrication qualities and load conditions. These system effects signify that an inspection of one hotspot provides indirect information of the condition of the remaining hotspots and thus enable an optimization of the inspection effort for a wind farm. The wind farm model consists of two levels: A turbine support structure (level 1 system model) is represented by its fatigue hotspots and their stochastic dependence. The fatigue performance of a hotspot is described by a probabilistic fracture mechanics (FM) fatigue model. The probabilistic model of the parameters of the FM fatigue model is calibrated based on design data and is thus directly linked to the design of the turbine support structures. Dependence among the fatigue performances of different hotspots in a turbine support structure is modeled by introducing correlations between the stochastic parameters of the FM fatigue models. A wind farm (level 2 system model) consists of different turbine support structures (level 1 system models). Additional correlations are introduced at wind farm level to account for the dependence among the fatigue behavior of hotspots belonging to different turbine support structures. The wind farm model enables the computation of (marginal) hotspot fatigue reliabilities, system fatigue reliabilities of individual turbine support structures and the system fatigue reliability of an entire wind farm. The probabilistic model of the parameters of the two-level system model can be consistently updated with inspection outcomes using Bayesian methods. The updated probabilistic model of the model parameters then forms the basis for updating the estimates of the fatigue reliabilities. We implement the wind farm model in a software tool named SysPark. The tool provides the means for planning inspections at wind farm level using an adaptive reliability-based threshold approach. In this approach, the first inspection campaign is planned in the year before the fatigue failure rates of the hotspots with the lowest fatigue reliabilities exceed a threshold failure rate. Once inspection results become available, the probabilistic model of the parameters of the wind farm model is updated. If repairs are performed, the wind farm model is additionally modified to describe the behavior of the repaired hotspots. The updated and modified model then enables the planning of the next inspection campaign and so on. The software tool is demonstrated in a case study considering a generic wind farm consisting of turbines with jacket support structures. T2 - Wind Energy Science Conference (WESC 2021) CY - Online Meeting DA - 25.05.2021 KW - Fatigue deterioration KW - Offshore wind farm KW - Inspection planning PY - 2021 AN - OPUS4-52767 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eichner, Lukas T1 - Probabilistische Systemidentifikation einer Versuchsstruktur für Substrukturen von Offshore-Windenergieanlagen mit statischen und dynamischen Messdaten N2 - In diesem Beitrag wird ein probabilistischer Ansatz zur Systemidentifikation für Tragstrukturen von Offshore-Windkraftanlagen vorgestellt. Der Schwerpunkt der Forschung liegt auf der Integration von globalen Systemantworten in Form von Eigenfrequenzen und -formen sowie Verschiebungen und Dehnungen als lokale Messdaten. Die unterschiedlichen Daten werden kombiniert für die Aktualisierung der Parameter eines Finite-Elemente-Modells genutzt. Zu diesem Zweck wird ein probabilistischer Ansatz nach Bayes verfolgt, um Vorwissen sowie Unsicherheiten einzubeziehen. Die Methodik wird bei einer Versuchsstruktur angewandt, die eine Jacket-Substruktur von Offshore-Windenergieanlagen nachbildet. Eine Systemidentifikation mit Hilfe von Überwachungsdaten ist wertvoll für Jacket-Substrukturen, da eine Zustandsanalyse für die Gewährleistung der strukturellen Integrität unerlässlich ist, aber hinsichtlich der schwierigen Offshore-Bedingungen möglichst effizient sein muss. In diesem Zusammenhang schafft diese Arbeit die Grundlage für eine Schadenserkennung, eine verbesserte Vorhersage der Ermüdungslebensdauer und optimierte Instandhaltungsstrategien. Während das Modell hinsichtlich der statischen Messdaten erfolgreich aktualisiert werden kann, sind Schwierigkeiten bei der Identifizierung der dynamischen Systemeigenschaften erkennbar. T2 - 8. VDI-Fachtagung Baudynamik 2025 CY - Würzburg, Germany DA - 02.04.2025 KW - Systemidentifikation KW - Versuchsstruktur KW - Jacket KW - Offshore-Windenergie PY - 2025 AN - OPUS4-62880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Integrating vibration monitoring into risk-based inspection and maintenance planning for deteriorating structural systems N2 - A reliability and risk-based framework for integrating vibration monitoring data in the planning of inspection and maintenance of deteriorating structural systems is discussed and demonstrated in a numerical example. T2 - Wind Energy Science Conference (WESC 2021) CY - Online Meeting DA - 25.05.2021 KW - Deterioration KW - Structural systems KW - Inspection KW - Vibration monitoring KW - Maintenance PY - 2021 AN - OPUS4-52766 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -