TY - CONF A1 - Auersch, Lutz T1 - Prognoseverfahren für Bahnerschütterungen – DIN 45672-3, VDI 3837, HighSpeed2 und die Fahrzeug-Fahrweg-Boden Wechselwirkung N2 - Die VDI Richtlinie 3837 enthält detaillierte Angaben zur Erschütterungsemission. Die DIN 45672-3 enthält nur den Tunnel- oder einen Bodenmesspunkt als Ausgangspunkt der Prognose. Die Erschütterungsanregung durch die Fahrzeug-Fahrweg-Wechselwirkung wird beschrieben. Die ERgebnisse der BAM stimmen sehr gut mit dem Prognosekonzept von Highspeed 2 überein. Dies wird an den Punkten 1. Störgrößen, 2. Achsimpulse, 3. Tunnelstrecken aufgezeigt. T2 - Norm-Arbeitsausschuss Schwingungsminderung in der Umgebung von Verkehrswegen CY - Frankfurt/M., Germany DA - 08.02.2023 KW - Normung KW - Bahnerschütterungen KW - Emission KW - Fahrzeug-Fahrweg-Boden-Wechselwirkung KW - Störgrößen KW - Achsimpulse KW - Tunnelstrecke PY - 2023 AN - OPUS4-56978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Modal analysis of road and rail bridges for damage detection and resonance prediction N2 - In the 1980s, the Federal Institute of Material Research and Testing started with modal analysis measurements of some bridges before and after repair. For one of the bridges, a structural health monitoring was installed 1994 which is still working up to now. It has been modified and extended several times. The monitoring was extended from the critical span to three neighbouring spans. A modal analysis of the whole bridge with seven spans have been done three times, twice together with EMPA of Switzerland. Additional calibration measurements have been done and additional evaluation procedures have been implemented for the monitoring of the steadily increasing loads from the road traffic. Additional sensors were installed such as strain gauges, crack-width, and temperature sensors. The strong influence of the temperature on the natural frequencies has been studied over the years. Later, a temperature compensation has been established and a weak aging trend has been found in the monitoring data. Now, the bridge will be demolished and replaced by a new bridge. Some results of this long-term monitoring will be shown and possible damages (changes of the pre-stress or the support structure) will be discussed. A second application of modal analysis will be demonstrated: the prediction of the resonances due to passing trains. The response of a bridge to passing trains can be calculated in frequency domain as the multiplication of three spectra, the axle sequence spectrum of the train, the transfer function of the bridge, and the modal force spectrum of a single passing load. A resonance occurs if a maximum of the train spectrum coincides with the maximum of the bridge spectrum. The amplitude at this resonance is strongly influenced by the modal force spectrum which is identical to the frequency or wavenumber spectrum of the corresponding mode shape. Therefore, modal analysis from calculation, impact measurements, wind and train measurements are necessary for the prediction of the resonance occurrence and amplification. Examples of mode shape spectra for single or multi-span bridges with simply supported or continuous spans will be shown, and some relations between mode shapes and resonance amplifications will be concluded. T2 - 11th International Operational Modal Analysis Conference (IOMAC) CY - Rennes, France DA - 20.05.2025 KW - Bridge monitoring KW - Multi-span bridges KW - Damage detection KW - Resonance PY - 2025 AN - OPUS4-63472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rogge, Andreas T1 - Large scale impact tests with reinforced concrete plates for impact safety N2 - As part of a nuclear safety research project, large-scale impact tests were conducted on reinforced concrete slabs to investigate the structural integrity of containment structures under aircraft crash scenarios. The aim was to experimentally validate numerical models for both hard and soft impact conditions. Using a drop tower, concrete slabs were subjected to controlled impacts with a 404 kg impactor dropped from a height of 9.5 meters. The tests included force measurements, photogrammetric evaluations, and 3D scans to analyze deformations and damage. A total of six impact experiments were performed (2x hard impact, 2x combined hard/soft impact). The results provide a robust basis for advancing safety assessments of nuclear facilities. T2 - SMiRT28 - 28th International Conference on Structural Mechanics In Reactor Technology CY - Toronto, Canada DA - 10.08.2025 KW - Experimental mechanics KW - Aircraft crash scenario KW - Coupled impact loading PY - 2025 AN - OPUS4-64126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schepers, Winfried T1 - Kritische Betrachtung der Impedanzfunktionen harmonisch angeregter Fundamente N2 - In den aktuellen Entwürfen des Eurocode 8 Teil 5 (FprEN 1998-5:2024) und auch des Euro-codes 7 Teil 3 (E DIN EN 1997-3:2022-10) werden Formeln für die Steifigkeiten eines Hal-braums mit einem darin eingebetteten starren masselosen Rechteckfundament gegenüber einer harmonischen Anregung angegeben. Die Formeln sind im Wesentlichen eine Kombination der Ergebnisse der Veröffentlichungen von Gazetas (1991) und Pais et al. (1988) über Forschungs-arbeiten, die in den 1980er Jahren durchgeführt wurden. Sie basieren auf numerischen Berech-nungen, deren Ergebnisse durch Ausgleichskurven approximiert wurden. Eine genauere Analyse der den Formeln zugrunde liegenden Veröffentlichungen zeigt einige Inkonsistenzen zwischen Eurocodes und den ursprünglichen Veröffentlichungen, deren Ursache nicht ohne weiteres er-kennbar ist. Darüber hinaus werden in den Eurocodes nur frequenzunabhängige Steifigkeiten angegeben. Das führt zu der Frage, wie verlässlich die Formeln sind. An zwei Beispielen wird nachfolgend die Notwendigkeit einer kritischen Verwendung der Impedanzfunktionen gezeigt. T2 - 19. D-A-CH Tagung Erdbebeningenieurwesen und Baudynamik CY - Vienna, Germany DA - 18.9.2025 KW - Impedanzen KW - Wellenausbreitung KW - Erschütterungen PY - 2025 AN - OPUS4-64188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Anwendungsszenarien und Referenzanwendungen sensorbasiertes Monitoring N2 - Präsentiert wird eine Kategorisierung von Anwendungsszenarien für sensorbasiertes Monitoring und die Planung für die Referenzbauwerke mit SHM-Anwendungen. Im Rahmen des Forschungsvorhabens Aistec Pro werden Anwendungsszenarien für sensorbasiertes Monitoring kategorisiert und in Referenzanwendungen umgesetzt. Der Vortrag gibt einen Überblick über die abgeschlossene Planung. T2 - Jahrestreffen Verbund Aistec-Pro CY - Bonn, Germany DA - 17.09.2025 KW - SHM KW - Monitoring KW - Brückensicherheit KW - Aistec Pro PY - 2025 AN - OPUS4-64124 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Haake, Gerrit T1 - ReNEW - Entscheidungstools für die Nutzungsverlängerung und das Repowering von Windenergieanlagen N2 - Der Vortrag gibt einen Überblick über gängige Nachnutzungskonzepte, die im Rahmen des Forschungsvorhabens ReNEW untersucht werden. Hierzu wir eine probabilistisches Entscheidungsmodell eingeführt. Die Möglichkeiten von Bauwerksertüchtigungen werden erörtert. T2 - RAVE ROWD Workshop 2024 CY - Hannover, Germany DA - 10.12.2024 KW - Windenergieanlagen KW - Bauwerksertüchtigung KW - Offshore-Windparks KW - Repowering PY - 2024 AN - OPUS4-62237 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Vibration-based system identification of a large steel box girder bridge N2 - The Bundesanstalt für Materialforschung und -prüfung (BAM) collaborates with TNO to develop a software framework for automated calibration of structural models based on monitoring data. The ultimate goal is to include such models in the asset management process of engineering structures. As a basis for developing the framework, a multi-span road bridge consisting of ten simply supported steel box girders was selected as a test case. Our group measured output-only vibration data from one box girder under ambient conditions. From the data, we determined eigenfrequencies and mode shapes. In parallel, we developed a preliminary structural model of the box girder for the purpose of predicting its modal properties. In this contribution, we provide an overview of the measurement campaign, the operational modal analysis, the structural modeling and qualitatively compare the identified with the predicted modes. As an outlook, we discuss the further steps in the calibration process and future applications of the calibrated model. T2 - XII International Conference on Structural Dynamics (EURODYN 2023) CY - Delft, Netherlands DA - 02.07.2023 KW - Bridge KW - Safety KW - Fatigue KW - Modal system identification KW - Model updating PY - 2023 AN - OPUS4-57863 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Balscheit, Hagen A1 - Schepers, Winfried A1 - Victor, Albrecht A1 - Daryaei, Reza A1 - Bianco, Marcelo A1 - Starost, Christina T1 - Close-out Webinar OWA VERBATIM N2 - The risk of pile base buckling is a major reason for high pile wall thicknesses in monopiles. The VERBATIM project - Verification of the buckling detection and behaviour of large monopiles - aimed to investigate buckling phenomena related to both the plastic deformation of the pile tip during installation and the buckling of the embedded pile near the seabed. Numerical models were developed and validated on the basis of extensive tests. This enables a better understanding of the buckling behaviour in order to reduce the wall thickness, which allows cost savings in the amount of steel and the development of safer and optimised structures. The previous design procedures were able to ensure the successful installation of the monopiles. However, as the size of monopiles continues to increase, the development of improved design methods for safe and cost-effective foundations is becoming increasingly important. The presentation provides an overview of the investigations carried out and the results. T2 - Webinar Carbon Trust Offshore Wind Accelerator CY - Online meeting DA - 22.05.2024 KW - Offshore Windenergy Pile Buckling PY - 2024 AN - OPUS4-60348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eichner, Lukas A1 - Thiele, Marc A1 - Hille, Falk A1 - Baeßler, Matthias T1 - Digitale Modellierungsprozesse in der wiederkehrenden Prüfung von Windenergieanlagen - DiMoWind-Inspect - Abschlusstreffen N2 - Dieses Dokument enthält die Präsentationsfolien des BAM-Teams beim Abschlusstreffen des Forschungsprojekts DiMoWind-Inspect. Es wurden die Arbeitspakete Datenmanagement, Referenzkennzeichnungssystem, Grundlagen der Schadensbewertung, Risikobasierte Inspektions- und Instandhaltungsplanung und Schadensdetektion mittels Risslumineszenz sowie eine abschließende Bewertung des Projekts vorgestellt. T2 - DiMoWind-Inspect - Abschlusstreffen CY - Berlin, Germany DA - 12.09.2024 KW - Building Information Modeling (BIM) KW - Referenzkennzeichnungssystem KW - Risslumineszenz (Riluminati) KW - Risikobasierte Inspektionsplanung (RBI) PY - 2024 AN - OPUS4-61054 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen T1 - Evaluation of pile tip buckling based on large scale tests N2 - Der Vortrag zum zugehörigen Konferenzbeitrag beschreibt eine groß angelegte Feldtestkampagne mit 16 Rammversuchen, um das Risiko des plastischen Versagens der Pfahlspitzen besser zu verstehen Ein numerisches Modell mit transientem Bodenkontakt zeigt eine gute Übereinstimmung mit den Testergebnissen. Parametervariationen verdeutlichen, wie empfindlich die Pfahlreaktion auf Imperfektionen und Randbedingungen ist. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG) CY - Nantes, France DA - 09.06.2025 KW - Pile Tip Buckling KW - Monopile KW - Offshore Windenergy KW - Driving Refusal KW - Large Scale Test PY - 2025 AN - OPUS4-63391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Probabilistic approaches to the design and assessment of offshore foundations considering spatially varying site conditions N2 - In this presentation, we discuss the potential of probabilistic approaches to the design and assessment of offshore foundations. The potential is demonstrated in a numerical example considering a laterally loaded monopile. As an outlook, we present a concept for managing the risk associated with installing large monopiles. T2 - 3rd International Conference on Structural Integrity for Offshore Energy Industry (SI 2021) CY - Online meeting DA - 15.11.2021 KW - Offhore KW - Foundations KW - Probabilistic KW - Design KW - Assessment PY - 2021 AN - OPUS4-53748 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis T1 - 3D spatial modelling of CPT data for probabilistic preliminary assessment of potential pile tip damage upon collision with boulders N2 - Tip damage of monopiles from boulder collisions during installation has emerged as a critical design issue, primarily due to the combination of the widespread use of large-diameter piles and the complexity of the ground conditions at the available sites. Recently, a framework relating potential pile tip damage to cone tip resistance from Cone Penetration Tests (CPTs) has been proposed in the literature. Gaussian processes are powerful stochastic models that enable probabilistic spatial interpolation of soil data at any location within a site. On this basis, this study utilizes sparse CPT data from a site in the North Sea, to first develop an efficient Gaussian process regression model, which is used to derive a three-dimensional (3D) probabilistic predictive map of the cone tip resistance. Assuming deterministic loading conditions and a factual collision with a boulder of pre-defined properties, the cone tip resistance predictive model is subsequently used for a probabilistic preliminary assessment of potential pile tip damage. Results of the analysis are realistic 3D probability maps of potential damage that aim to support engineering judgment and contribute towards cost-effective site investigation planning and offshore wind farm design. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG) CY - Nantes, France DA - 09.06.2025 KW - CPT data KW - Gaussian process regression KW - Boulder impact KW - Preliminary pile tip damage assessment PY - 2025 AN - OPUS4-63444 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kemmler, Samuel T1 - Gekoppelte Fluid Partikel Simulationen einer Suction Bucket Gründung zur Analyse von Piping Erosion während der Installation von Offshore Windkraftanlagen N2 - Wir stellen unseren Ansatz und unsere Methodik zur Simulation von Piping-Erosion vor, welche während des Installationsprozesses von Suction Bucket Fundamenten für Offshore-Windkraftanlagen auftreten kann und ein kritisches Versagen des Installationsprozesses darstellt. Wir zeigen die Ergebnisse mehrere Simulationen und analysieren die hydrodynamischen und Kontaktkräfte, die auf das granulare Medium wirken, sowie die Druckdifferenz der flüssigen Phase. Solche Simulationen können zum besseren Verständnis von Piping-Erosion und letztendlich zu dessen Verhinderung beitragen. T2 - Gesinus-Treffen 2024 CY - Stuttgart, Germany DA - 20.06.2024 KW - Suction Bucket KW - Gekoppelte Fluid-Partikel Simulationen KW - Offshore-Windkraftanlagen PY - 2024 AN - OPUS4-60516 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Numerical Modelling of Local Pile Deformations and Buckling incorporating the Pile-Soil-Interaction N2 - Pile Tip Buckling and Buckling of embedded piles both depend very much on the pile-soil-interaction and its modelling. The presentation gives an overview about current problems and research activities in the light of the development of numerical models. T2 - WESC Wind Energy Science Conference CY - Hannover, Germany DA - 25.05.2021 KW - Offshore Wind Energy Converter KW - Pile Foundation KW - Monopile Buckling KW - Pile Tip Buckling PY - 2021 AN - OPUS4-53033 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis T1 - Stochastic variational Gaussian process for 3D site characterization N2 - This work was presented at the the 2nd Workshop on Future of Machine Learning in Geotechnics (2FOMLIG) & the 5th Machine Learning in Geotechnics Dialogue (5MLIGD), in Chengdu, China. In this study, we propose an efficient multivariate Gaussian process regression model, utilizing the Linear Model of Coregionalization, stochastic variational inference and Dirichlet-based transformations, to jointly model continuous CPT and categorical (USCS) borehole variables. The predictive performance of the model is assessed using a real dataset from a site located in Christchurch, New Zealand. T2 - 2nd Workshop on Future of Machine Learning in Geotechnics (2FOMLIG) & the 5th Machine Learning in Geotechnics Dialogue (5MLIGD) CY - Chengdu, China DA - 11.10.2024 KW - Geotechnical site-characterization KW - Cone Penetration Tests KW - Multivariate Gaussian process regression KW - Categorical borehole data KW - Stratigraphy prediction KW - Linear Model of Coregionalization PY - 2024 AN - OPUS4-61775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Die Minderung von Bahnerschütterungen – Messergebnisse aus Österreich, Deutschland und der Schweiz N2 - Die Minderung von Bahnerschütterungen neben Eisenbahnstrecken ist an vielen Stellen gemessen worden. Dabei ist neben der hochfrequenten Wirkung von elastischen Gleiselementen wie Schienenlager, Schwellensohlen und Unterschottermatten auch oft eine tieffrequente Minderung beobachtet worden. Diese tieffrequente Minderung wird interpretiert und mit der weiteren Lastverteilung der statischen Last erklärt. T2 - Wiener Dynamik Tage CY - Vienna, Austria DA - 25.07.2027 KW - Bahnerschütterungen KW - Minderung KW - Messungen KW - Schwellensohlen KW - Unterschottermatte KW - Gleistrog PY - 2024 AN - OPUS4-61228 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Vibraciones de estructuras multi vanos como forjados, puentes ferroviarios y de carreteras N2 - Se han analizado las frecuencias y las formas modales de las estructuras multi-vanos en teoría y mediante ocho ejemplos medidos. Como consecuencia por los puentes de ferrocarril, se han calculado las amplitudes de resonancia en el dominio de las frecuencias con los espectros del tren, de la fuerza modal, y de la resonancia. Para los vanos (idénticos) continuos resp. simplemente apoyados el acoplamiento es fuerte resp. debil, las frecuencias son separadas resp. agrupadas, las formas modales son globales y globales, la resonancia es menor resp. menor – (igual). Los resultados en el dominio del tiempo se obtiene con la transformación inversa de Fourier o – más robusto – el valor de eficaz por la superposición. T2 - DinEst 2024 Third Conference on Structural Dynamics CY - Seville, Spain DA - 12.09.2024 KW - Multi-span bridges KW - Train passage KW - Resonance PY - 2024 AN - OPUS4-61225 LA - spa AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - The excitation, propagation, and mitigation of train-induced ground vibrations from the axle impulses on the track N2 - Train-induced vibrations in soft ground usually have a strong low-frequency component. This component has a characteristic spectrum which is related to the axle sequence and the speed of the train. Its attenuation with distance is weaker than the attenuation for higher frequencies, and it always dominates the far-field ground vibration. Narrow-band frequency analyses clearly show that this ground vibration component is due to the static axle loads. Axle box vibrations have a different characteristic where the first out-of-roundness of the wheels is the only remarkable low-frequency component. Therefore, the dynamic axle loads from wheel and track irregularities are not the reason for the strong ground vibration component. The moving static axle loads generate the quasi-static response of the soil at very low frequencies and at very near distances. A part of the original impulse spectrum is scattered when it propagates through an inhomogeneous ballast and soil with a randomly varying stiffness. The axle impulses are smoother for a higher bending stiffness or a lower support stiffness (under sleeper pads, under ballast mats) of the track. This mitigation of the ground vibration will be demonstrated by measurements at three sites in Switzerland as well as the characteristic of the soil and axle-box vibrations. T2 - Railways Conference CY - Prague, Czech Republic DA - 02.09.2024 KW - Soil and vehicle measurements KW - Train passages KW - Ground vibration KW - Excitation mechanisms KW - Mitigation KW - Under sleeper pads KW - Under ballast mat PY - 2024 AN - OPUS4-61226 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz A1 - Song, Jiaojiao T1 - Analysis of intact and damaged (floating) slab tracks by finite-element boundary-element models and by measurements N2 - The damage detection and repair control have become important tasks for slab tracks. Different intact and damaged slab tracks have been investigated theoretically and experimentally for train passages and hammer impacts. The following damages have been considered: The loss of contact between the sleeper and the track slab, between the track slab and the base slab, and between the base slab and the base layer. At first, a slab track with a gap between the track slab and the base layer has been calculated by the combined finite-element boundary-element method which correctly incorporates the behaviour of the infinite soil. The basic results are the track displacements of the rail, the track slab, and the base layer along the track which are caused by a single axle load. These solutions are properly superposed for to get the complete train load. The influence of track and soil parameters and of the track damage has been analysed. For the intact track, the compliance of the soil is dominant whereas the track bending stiffness becomes more important for the damaged track. By comparing the calculated results with the measurements, the length of the gap could be quantified. A slab track with a loose sleeper (without contact to the supporting track slab) was analysed by the transfer function between the displacements and the hammer force (receptance functions) where a resonance appeared in case of the damage. Differences between the different track elements confirmed the detection of the damage. A floating slab track with a thin rubber layer has been investigated for a possible gap between the base slab and the base layer. The behaviour of the intact track has been calculated by a wavenumber-domain method, and the same behaviour has been found in the measurements at several track sections, indicating that there is no damage. Finally, a floating slab track with steel springs and viscous fluid dampers has been measured in the Tongji laboratory. The modes of the floating track slab and the transfer function with corresponding resonances have been calculated and successfully compared with results from wheelset drop tests. T2 - 3rd International Conference of Rail Transportation CY - Shanghai, China DA - 07.08.2024 KW - Slab tracks KW - Damage KW - Vibration measurements KW - Finite-element boundary-element method PY - 2024 AN - OPUS4-61227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - System and damage identification for cars, floors and roofs, bridges, tracks and foundations by modal analyses, frequency response functions and moving load responses N2 - The following objects have been analysed by frequency response functions and moving load responses. A simple modal analysis which is based on the transformed and weighted system equations has been tested for an automotive test car and for many floors in many buildings to get some rules for their natural frequency and damping. Moreover, six neighboured equal, weakly coupled, wooden floors in a castle have been measured by ambient and hammer excitation, and a special method to extract the different mode shapes of the closely spaced natural frequencies has been developed and tested. Different foundations, for which the soil-structure interaction is generally important, have been measured and compared with finite-element boundary-element models of varying soil properties. Similarly by FEBEM calculations, damages in railway tracks have been identified from flexibility functions (frequency response functions) and from the moving-load responses to normal train operation. Rail and foot bridges have been measured during train passages and by quasi-static tests with moving vehicles. The repeatability of the inclinometer measurements has been checked for different passages, passage directions, and measurement campaigns at a six-span foot bridge. Two rail bridges at the Hanover-Würzburg high-speed line have been measured and evaluated for integrity and for the train- and speed-dependent bridge resonances. The relation between the multi-axle and the single-axle excitation can be solved in frequency domain by the axle-sequence spectrum of the vehicle or the whole train. The single axle response has been used to identify track and bridge damages in laboratory and in situ. T2 - 10th International Operational Modal Analysis Conference (IOMAC 2024) CY - Naples, Italy DA - 21.05.2024 KW - Weakly coupled floors KW - Bridge passage KW - Track damage KW - Foundation-soil interaction KW - Flexibility function KW - Moving load response PY - 2024 AN - OPUS4-61233 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -