TY - CONF A1 - Balscheit, Hagen T1 - Buckling Design of Soil Embedded Piles N2 - Monopiles sind die gängigste Gründungskonstruktion für Offshore-Windkraftanlagen, doch größere Turbinen erfordern Pfahldurchmesser über 10 m und Pfahllängen über 60 m, was das Risiko von lokalem Beulen in den eingebetteten Bereichen erhöht. Aktuelle Richtlinien berücksichtigen die Pfahl-Boden-Interaktion nicht ausreichend so dass nur ein vollständig numerischer GMNIA-Nachweis geführt werden kann. Für derartige Berechnungsmodelle fehlen allerdings derzeit noch validierungswerte für eingebettete Schalen. Experimente im Rahmen des VERBATIM-Projekts schließen diese Lücke. T2 - Phd Conference Univiersity Innsbruck CY - Innsbruck, Austria DA - 05.02.2025 KW - Buckling KW - Wind Energy KW - Monopile Foundation PY - 2025 AN - OPUS4-62534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit A1 - Hering, Marcus T1 - Eine Machbarkeitsstudie zur Skalierung von Sprengversuchen an Stahlbetonbauteilen N2 - Sprengversuche sind erforderlich, um Explosionsereignisse auf Grund von Unfällen oder Anschlägen zu untersuchen und um das Schutzniveau für Menschen und Anlagen in kritischen Infrastrukturen zu bewerten. Die Durchführung von Feldversuchen in großem Maßstab für komplexe Szenarien ist sehr ressourcenintensiv. Verlässliche Experimente im kleinen Maßstab sind eine vielversprechende Alternative. Die Skalierungsgesetze für die Bemessung von Stahlbetonkonstruktionen unter Explosionsbelastung sind jedoch nicht hinreichend etabliert. Die Forschungsarbeit fokussiert sich auf Stahlbetonstrukturen, die für die Standardisierung von skalierten Sprengversuchen in Frage kommen. Im Rahmen der Machbarkeitsstudie wurden auf dem TTS-Gelände Sprengversuche an Probekörpern unterschiedlicher Größe durchgeführt. Dabei wurden verschiedene horizontal gelagerte Stahlbetonplatten getestet und unterschiedlichen Explosionsbelastungen ausgesetzt. Die Sprengversuche umfassten verschiedene Messtechniken zur Quantifizierung der Explosionslast sowie des Verhaltens der Stahlbetonplatten. Die Explosionslast wurde mit bündig eingebauten piezoelektrischen Druckmessern gemessen, während Beschleunigungssensoren und flächig applizierte verteilte faseroptische Sensorik verwendet wurden, um das dynamische Verhalten der Platte unter Explosionsbelastung zu charakterisieren. Darüber hinaus wurden Schädigungsmerkmale ebenfalls mit verteilter faseroptischer Sensorik ermittelt. Die Anwendung solcher Messtechniken sowie die Nutzung verschiedener numerischer Softwaretools bieten die Möglichkeit die Skalierungsgesetze zu verifizieren bzw. anzupassen. T2 - BBK - Fachkongress Forschung für den Bevölkerungsschutz 2025 CY - Bonn, Germany DA - 05.02.2025 KW - Sprengversuch KW - Skalierung KW - Faseroptik PY - 2025 AN - OPUS4-62509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Digitaler Zwilling im Erhaltungsmanagement von Straßenbrücken N2 - Digitale Zwillinge werden zukünftig ein integraler Bestandteil des Erhaltungsmanagements von Straßenbrücken sein. In diesem Beitrag wird argumentiert, dass sie nicht nur als digitale Abbilder physikalischer Bauwerke verstanden werden sollten, sondern als eine umfassende digitale Methode, die durch die Integration von Datenerfassung, Erhaltungsmaßnahmen, Datenmanagement, Bauwerksbewertung und Entscheidungsunterstützung die Bauwerksüberwachung und -erhaltung verbessert. In diesem Zusammenhang wird betont, dass der Übergang von der reaktiven zur prädiktiven Erhaltung durch den Einsatz von Digitalen Zwillingen nur dann realisierbar ist, wenn neben den erforderlichen diagnostischen und prognostischen Zustandsanalysen auch Methoden zur Optimierung von Entscheidungen über Datenerfassung und Erhaltungsmaßnahmen implementiert werden. Zur Veranschaulichung der Diskussion werden in diesem Beitrag exemplarisch zwei Bestandteile eines Digitalen Zwillings für das Erhaltungsmanagement von Verkehrsbrücken am Beispiel einer Eisenbahnbrücke demonstriert. Dabei wird zum einen gezeigt, wie Monitoringdaten mittels eines Datenmanagementsystems strukturiert verwaltet und für angeknüpfte Analysen bereitgestellt werden. Zum anderen erfolgt im Rahmen einer bauwerksspezifischen Einwirkungsermittlung eine Zugidentifikation anhand von gemessenen Schwellenschwingungen T2 - Workshop „Digitaler Zwilling im Lebenszyklusmanagement" der AG BIM in der Bauwerkserhaltung des Koordinierungsausschusses Erhaltung (KoA-Erhaltung) der B/L-DB Konstruktiver Ingenieurbau CY - Potsdam, Germany DA - 09.04.2025 KW - Digitale Zwillinge KW - Erhaltung KW - Inspektion KW - Monitoring KW - Brücken PY - 2025 AN - OPUS4-62951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf T1 - Managing Structural Health Monitoring with the Research Data Management Platform BAM Data Store N2 - Structural Health Monitoring (SHM) is an interdisciplinary challenge involving the assessment and prediction of the condition of civil structures, such as bridges, based on measurements and models. This presentation provides insight into how the BAM Data Store is used to represent a SHM project including the metadata and the monitoring data, itself. It describes the structure of the core elements of a typical SHM and introduces metadata profiles. This enables linking objects within the BAM Data Store to create a hierarchical structure. N2 - Structural Health Monitoring (SHM) ist eine interdisziplinäre Aufgabe bei der es um die Bewertung und Zustandsprognose von Bauwerken, wie z. B. Brücken, auf der Grundlage von Messungen und Modellen geht. Die Präsentation gibt einen Einblick in die Verwendung des BAM Data Stores zur Abbildung eines SHM Projekts zum Datenmanagement aller relevanten Metadaten und der Monitoringdaten selbst. Es werden die Struktur der Kernelemente eines typischen SHM beschrieben und Metadatenprofile für diese vorgestellt. Im BAM Data Store werden damit die strukturierte Verknüpfung von Objekten ermöglicht, um eine hierarchische Struktur zu erzeugen. T2 - Data Store Days 2025 CY - Berlin, Germany DA - 09.04.2025 KW - Structural Health Monitoring (SHM) KW - BAM Data Store KW - Verkehrsinfrastrukturen PY - 2025 AN - OPUS4-62942 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eichner, Lukas T1 - Probabilistische Systemidentifikation einer Versuchsstruktur für Substrukturen von Offshore-Windenergieanlagen mit statischen und dynamischen Messdaten N2 - In diesem Beitrag wird ein probabilistischer Ansatz zur Systemidentifikation für Tragstrukturen von Offshore-Windkraftanlagen vorgestellt. Der Schwerpunkt der Forschung liegt auf der Integration von globalen Systemantworten in Form von Eigenfrequenzen und -formen sowie Verschiebungen und Dehnungen als lokale Messdaten. Die unterschiedlichen Daten werden kombiniert für die Aktualisierung der Parameter eines Finite-Elemente-Modells genutzt. Zu diesem Zweck wird ein probabilistischer Ansatz nach Bayes verfolgt, um Vorwissen sowie Unsicherheiten einzubeziehen. Die Methodik wird bei einer Versuchsstruktur angewandt, die eine Jacket-Substruktur von Offshore-Windenergieanlagen nachbildet. Eine Systemidentifikation mit Hilfe von Überwachungsdaten ist wertvoll für Jacket-Substrukturen, da eine Zustandsanalyse für die Gewährleistung der strukturellen Integrität unerlässlich ist, aber hinsichtlich der schwierigen Offshore-Bedingungen möglichst effizient sein muss. In diesem Zusammenhang schafft diese Arbeit die Grundlage für eine Schadenserkennung, eine verbesserte Vorhersage der Ermüdungslebensdauer und optimierte Instandhaltungsstrategien. Während das Modell hinsichtlich der statischen Messdaten erfolgreich aktualisiert werden kann, sind Schwierigkeiten bei der Identifizierung der dynamischen Systemeigenschaften erkennbar. T2 - 8. VDI-Fachtagung Baudynamik 2025 CY - Würzburg, Germany DA - 02.04.2025 KW - Systemidentifikation KW - Versuchsstruktur KW - Jacket KW - Offshore-Windenergie PY - 2025 AN - OPUS4-62880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Maßgeblicher Einfluss geotechnischer Interaktionsprobleme auf den Tragwerksentwurf: Zwei spezielle Fallbeispiele N2 - Geotechnische Interaktionsprobleme können den Entwurf eines Tragwerks maßgeblich beeinflussen. Anhand zweier Fallbeispiele - dem Schotteroberbau auf Brücken im HGV und der Installation großer Monopiles - werden aktuelle Fälle aus dem Forschungsrepertoire der BAM vorgestellt. T2 - Geotechnische Seminarreihe am IBF des KIT CY - Karlsruhe, Germany DA - 23.01.2025 KW - Schotter auf Brücken im Hochgeschwindigkeitsverkehr KW - Pfahlfussbeulen KW - Beschleunigungsgrenzwert KW - Rammung KW - Monopiles PY - 2025 AN - OPUS4-62451 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Characteristic Frequencies of Train-Induced Bridge, Track, Ground and Building Vibrations – Excitation and Mitigation N2 - The characteristic frequencies of train-induced vibrations are discussed in theory and experiment following the propagation of vibrations from the source to the receiver: 1. Out-of-roundness frequencies of the wheels, 2. sleeper-passage frequency, 3. the vehicle-track eigenfrequency, 4. band frequency of the impulses of the passing static axle loads, 5. car-length frequency and multiples, 6. axle-distance frequencies with two characteristic zeros, 7. bridge eigenfrequencies, 8. the cut-on frequency due to the layering, and 9. the cut-off frequency due to the material damping of the soil, 10. the building-soil eigenfrequency, 11. as a rigid building or flexible wall/column mode, 12. floor eigenfrequencies, 13. acoustic room resonances, 14. the „resonance“ frequency or cut-off frequency of a base isolation. Coincidences of some of these characteristic frequencies or frequency ranges can be typically problematic and mitigation measures at the track or at the building can be necessary. The bridge response to the passing static loads is deter¬mined by the axle-sequence spectrum, the eigenfrequency (transfer function) of the bridge, and the modal force or mode shape spectrum. The ground vibration has typically high frequencies for a stiff soil and low frequencies for a soft soil. The high amplitudes between the zeros of the axle-sequence spectrum are often measured in the ground vibrations, and they can be mitigated by soft support elements or a higher bending stiffness of the track. T2 - EVACES 2025 CY - Porto, Portugal DA - 02.07.2025 KW - Train-induced vibration KW - Axle-sequence spectrum KW - Vehicle-track eigenfrequency KW - Axle impulses PY - 2025 AN - OPUS4-63654 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agasty, Amit T1 - Replica scaling of RC slabs under blast loading: a preliminary assessment N2 - Blast testing is undoubtedly the most straightforward and direct method of evaluating the blast resistance of a structure. For the calibration and validation of numerical models as well, blast tests must be carried out. However, true-scale prototype testing under different blast loading scenarios is not always feasible. Reliable small-scale experiments are a promising alternative. Application of dimensional analysis and similarity principals can be found in different engineering fields. For applications to the phenomenon of shock wave propagation, Hopkinson-Cranz or cube-root scaling is a well-established concept. When it comes to the scaling the structural response, research has predominantly focused on structures made of metallic materials. Scaled investigations with concrete or reinforced concrete (RC) structures remain limited, specifically under blast loading. In a preliminary study, we tested RC slabs at two different scales under near-field blast loading. Replica scaling, which is geometrical scaling while using the same materials at different scales, was implemented in the construction of the test specimens. The assessment of scaling and the discrepancy in its application was investigated by characterizing the blast loads, dynamic response, and damage. The experiments were supplemented by numerical simulations of these scenarios. The quantification of scenario-and-response-specific discrepancy can be used to modify the scaling laws, so that a blast assessment can be performed based on resource efficient small-scale tests. T2 - 25th International Physical Security Forum CY - Schwarzenburg, Switzerland DA - 11.05.2025 KW - Blast KW - RC slabs KW - Scaling PY - 2025 AN - OPUS4-63184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Costard, René T1 - Explosionsauswirkungen auf Strukturen Versuche und Simulationen N2 - Vorstellung der Versuche von Explosionsversuchen auf dem TTS. Diese werden ergänzt durch die Ergebnisse durchgeführter Simulationen und zeigen die Wirkung von zivilen Explosivstoffen auf Gebäudestrukturen und die aufgetretenen Schädigungen. T2 - 46. Informationstagung Sprengtechnik CY - Siegen, Germany DA - 25.04.2025 KW - Explosivstoff KW - Skalierung KW - Strukturauswirkung KW - Numerische Simulation PY - 2025 AN - OPUS4-62998 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Erschütterungsprognose mit KI? Schnelle Ersatzmodelle und physikbasiertes maschinelles Lernen in der Bauwerk-Boden-Dynamik N2 - Erschütterungsprognosen können mit sehr detaillierten Modellen durchgeführt werden. Dies ist sowohl bei der Erstellung des Modells (zum Beispiel für ein Finite-Element-Modell für Boden und Bauwerk), als auch bei der Berechnung zeitaufwändig, von einigen Minuten für die Wellenausbreitung in geschichteten Böden mit Wellenzahlintegralen bis zu mehreren Stunden für Randelementlösungen für die korrekte Bauwerk-Boden-Wechselwirkung. Hier sind einfache und schnelle Ersatzmodelle von Vorteil, die die Ergebnisse der detaillierten Berechnungen gut wiedergeben. Diese Ersatzmodelle können vollständig auf physikalischen Überlegungen beruhen (white-box Modelle) oder mit Hilfe von maschinellem Lernen aus einer Vielzahl von detaillierten Rechenergebnissen erzeugt werden (black-box Modelle). Erfahrungen mit black-box Modellen zeigen, dass es sinnvoll ist das maschinelle Lernen mit physikalischen Informationen anzureichern (grey-box Modelle). Es werden Anwendungsmöglichkeiten für physikbasiertes maschinelles Lernen im Bereich von Bahnerschütterungen aufgezeigt, die Erschütterungsemission durch die Fahrzeug-Fahrweg-Wechselwirkung, die Wellenausbreitung im Boden, die Erschütterungsimmission in Gebäude, Gleisschäden und das Monitoring von Eisenbahnbrücken. T2 - VDI-Tagung Baudynamik CY - Würzburg, Germany DA - 02.04.2025 KW - Bahnerschütterungen KW - Emissionsmodell KW - Immissionsmodell KW - Transmissionsmodell KW - Tunnelausbreitung KW - Gleisüberwachung PY - 2025 AN - OPUS4-62889 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Frequency-wavenumber method for the wave propagation through the soil and the soil-structure interaction of railway tracks and building foundations near railway lines N2 - In soil-structure interaction, the soil and the (flexible) structures are modelled as elastic continua. The partial differential equations of elasticity can be transformed to algebraic equations in frequency-wavenumber domain where they can be solved by matrix methods. The results for the soil and a structure can be coupled in frequency-wavenumber domain, and the solution in space domain is obtained by an infinite wavenumber integral (the back-transformation). This method has several applications for the prediction of the emission, transmission and immission of railway-induced vibrations. The wave propagation in homogeneous or layered soils is calculated for surface and tunnel lines by a single wavenumber integration (transmission). The response of ballast or slab tracks (for the emission problem) and the foundation stiffness (for the immission problem) need an additional integration across the track or foundation width. In wavenumber domain, tracks and foundations of infinite length are analysed. Finite structures can be calculated by finite element models where the soil is calculated by the boundary element method. The Green’s functions for the boundary element method are calculated by a wavenumber integration as for the transmission problem. Some example results for all these tasks will be shown. The immission into buildings will be analysed in detail, and the effect of stiff slab foundations and (basement) walls on the incoming wavefield is quantified in a parameter study. The transfer function (the amplitude ratio) structure to free field usually starts with 1 at 0 Hz and decreases continuously with frequency. The reduction is due to the structural stiffness against wave deformation which turns to be higher than the stiffness of the soil, for example above the structure-soil coincidence frequency of the slab foundation. The reduction is better for a high structural stiffness and for a low soil stiffness. Walls are stiffer than plates for the relevant frequency range, but even walls and especially low basement walls are not infinitely rigid and can follow the wave deformation to a certain extent. These basic rules from frequency-wavenumber analysis can well be used for real building projects near railway lines where stiff foundations can be an alternative reduction method to the commonly used base isolation by elastic elements. T2 - COMPDYN 2025 CY - Rhodos, Greece DA - 15.06.2025 KW - Frequency-wavenumber method KW - Wave propagation KW - Soil-structure interaction KW - Building foundations KW - Mitigation measures PY - 2025 AN - OPUS4-63468 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Artinov, Antoni T1 - Fracture Mechanics-Based Approach for Fatigue Life Assessment of Welded Structures: The Role of Real Weld Geometries and Welding Residual Stresses N2 - Fatigue failure is a critical concern in offshore wind structures, where welded joints are subjected to cyclic loading over extended service lifetimes. The combined effects of weld geometry [1, 2] and welding residual stresses (WRS) significantly influence the fatigue strength of welds [3-5]. In offshore wind applications, fatigue behavior is further complicated by cyclic loading conditions, where externally applied loads from wind, waves, and ocean currents interact with WRS, causing localized plastic deformation due to high-stress concentrations. Additionally, under prolonged cyclic loading, the redistribution of WRS can result in a shift of the fatigue-prone regions over time, meaning that locations identified as high-risk may not remain the dominant failure sites throughout the structure’s service life [6]. This presents a significant challenge for inspection and maintenance strategies, as conventional monitoring approaches may fail to detect the most vulnerable zones at later stages of operation. Early experimental studies on low-carbon steel plates and butt joints have shown that tensile WRS can reduce fatigue limits by up to 50% compared to stress-relieved specimens [7]. This effect is particularly pronounced in regions with welding defects, such as porosity, lack of fusion, and undercuts, as well as at geometric discontinuities, including weld toes and sharp notches, which induce localized stress gradients. The combined effect of tensile WRS and stress concentrations amplifies the local stress fields, promoting crack initiation and accelerating crack propagation, ultimately reducing the service life of offshore wind structures. Despite the critical role of weld geometry and WRS in fatigue performance, conventional fatigue assessment methods frequently neglect or oversimplify their effects, leading to overly conservative predictions and suboptimal structural designs. Current engineering standards, including BS 7910 (2019), BS 7608 (1993), EN 13001-3-1 (2020), and EN 1993-1-9 (2013), assume high tensile WRS in welded joints and apply simplified fatigue life prediction approaches that eliminate the need for explicit mean stress considerations. While some standards introduce correction factors for different WRS states, these remain highly generalized and lack accuracy. More sophisticated approaches, such as the Integrated Approach to Fatigue Strength Determination of Welded Structures (IBESS) [8], attempt to incorporate WRS into fatigue life assessments but rely on effective load ratios rather than explicitly modeling and considering real WRS distributions in the analysis. Additionally, IBESS does not fully integrate real weld geometries, limiting its predictive accuracy. These limitations result in significant scatter in fatigue life predictions, excessive conservatism, and inefficiencies in structural design. Although existing fatigue models improve on traditional methodologies, to the best of the authors' knowledge a unified framework that fully captures the combined effects of real weld geometries, WRS, and cyclic loading does not exist yet. The present research aims to develop an advanced fracture mechanics-based numerical framework for fatigue life assessment that explicitly accounts for these influencing factors at the specimen level, establishing the foundation for future scaling to component-level applications. T2 - Wind Energy Science Conference CY - Nantes, France DA - 23.06.2025 KW - Fatigue Assessment KW - Wind Offshore Structures KW - Fracture Mechanics KW - Digital Weld Geometries KW - Welding Residual Stresses KW - Numerical Modeling PY - 2025 AN - OPUS4-63591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Costard, Rene A1 - Hering, Marcus T1 - Explosionsauswirkungen auf Strukturen N2 - Wir berichten über die Entwicklungen des AP2 im Hinblick auf Explosionsauswirkungen auf Strukturen und den Weg zur systematischen messtechnischen Erfassung zur ganzheitlichen Bewertung der Bauwerksicherheit unter Detonationsbelastung. Zusätzlich werden die Vorführungen zu Kontaktdetonationen während der 16. Informationsveanstaltung Sprengstoffe und Pyrotechnik vorgeführt. T2 - 16. Informationsveranstaltung Sprengstoffe und Pyrotechnik CY - Berlin, Germany DA - 20.05.2025 KW - Explosion KW - Kontaktdetonation KW - Blast PY - 2025 AN - OPUS4-63192 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Modal analysis of road and rail bridges for damage detection and resonance prediction N2 - In the 1980s, the Federal Institute of Material Research and Testing started with modal analysis measurements of some bridges before and after repair. For one of the bridges, a structural health monitoring was installed 1994 which is still working up to now. It has been modified and extended several times. The monitoring was extended from the critical span to three neighbouring spans. A modal analysis of the whole bridge with seven spans have been done three times, twice together with EMPA of Switzerland. Additional calibration measurements have been done and additional evaluation procedures have been implemented for the monitoring of the steadily increasing loads from the road traffic. Additional sensors were installed such as strain gauges, crack-width, and temperature sensors. The strong influence of the temperature on the natural frequencies has been studied over the years. Later, a temperature compensation has been established and a weak aging trend has been found in the monitoring data. Now, the bridge will be demolished and replaced by a new bridge. Some results of this long-term monitoring will be shown and possible damages (changes of the pre-stress or the support structure) will be discussed. A second application of modal analysis will be demonstrated: the prediction of the resonances due to passing trains. The response of a bridge to passing trains can be calculated in frequency domain as the multiplication of three spectra, the axle sequence spectrum of the train, the transfer function of the bridge, and the modal force spectrum of a single passing load. A resonance occurs if a maximum of the train spectrum coincides with the maximum of the bridge spectrum. The amplitude at this resonance is strongly influenced by the modal force spectrum which is identical to the frequency or wavenumber spectrum of the corresponding mode shape. Therefore, modal analysis from calculation, impact measurements, wind and train measurements are necessary for the prediction of the resonance occurrence and amplification. Examples of mode shape spectra for single or multi-span bridges with simply supported or continuous spans will be shown, and some relations between mode shapes and resonance amplifications will be concluded. T2 - 11th International Operational Modal Analysis Conference (IOMAC) CY - Rennes, France DA - 20.05.2025 KW - Bridge monitoring KW - Multi-span bridges KW - Damage detection KW - Resonance PY - 2025 AN - OPUS4-63472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rogge, Andreas T1 - Large scale impact tests with reinforced concrete plates for impact safety N2 - As part of a nuclear safety research project, large-scale impact tests were conducted on reinforced concrete slabs to investigate the structural integrity of containment structures under aircraft crash scenarios. The aim was to experimentally validate numerical models for both hard and soft impact conditions. Using a drop tower, concrete slabs were subjected to controlled impacts with a 404 kg impactor dropped from a height of 9.5 meters. The tests included force measurements, photogrammetric evaluations, and 3D scans to analyze deformations and damage. A total of six impact experiments were performed (2x hard impact, 2x combined hard/soft impact). The results provide a robust basis for advancing safety assessments of nuclear facilities. T2 - SMiRT28 - 28th International Conference on Structural Mechanics In Reactor Technology CY - Toronto, Canada DA - 10.08.2025 KW - Experimental mechanics KW - Aircraft crash scenario KW - Coupled impact loading PY - 2025 AN - OPUS4-64126 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schepers, Winfried T1 - Kritische Betrachtung der Impedanzfunktionen harmonisch angeregter Fundamente N2 - In den aktuellen Entwürfen des Eurocode 8 Teil 5 (FprEN 1998-5:2024) und auch des Euro-codes 7 Teil 3 (E DIN EN 1997-3:2022-10) werden Formeln für die Steifigkeiten eines Hal-braums mit einem darin eingebetteten starren masselosen Rechteckfundament gegenüber einer harmonischen Anregung angegeben. Die Formeln sind im Wesentlichen eine Kombination der Ergebnisse der Veröffentlichungen von Gazetas (1991) und Pais et al. (1988) über Forschungs-arbeiten, die in den 1980er Jahren durchgeführt wurden. Sie basieren auf numerischen Berech-nungen, deren Ergebnisse durch Ausgleichskurven approximiert wurden. Eine genauere Analyse der den Formeln zugrunde liegenden Veröffentlichungen zeigt einige Inkonsistenzen zwischen Eurocodes und den ursprünglichen Veröffentlichungen, deren Ursache nicht ohne weiteres er-kennbar ist. Darüber hinaus werden in den Eurocodes nur frequenzunabhängige Steifigkeiten angegeben. Das führt zu der Frage, wie verlässlich die Formeln sind. An zwei Beispielen wird nachfolgend die Notwendigkeit einer kritischen Verwendung der Impedanzfunktionen gezeigt. T2 - 19. D-A-CH Tagung Erdbebeningenieurwesen und Baudynamik CY - Vienna, Germany DA - 18.9.2025 KW - Impedanzen KW - Wellenausbreitung KW - Erschütterungen PY - 2025 AN - OPUS4-64188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Anwendungsszenarien und Referenzanwendungen sensorbasiertes Monitoring N2 - Präsentiert wird eine Kategorisierung von Anwendungsszenarien für sensorbasiertes Monitoring und die Planung für die Referenzbauwerke mit SHM-Anwendungen. Im Rahmen des Forschungsvorhabens Aistec Pro werden Anwendungsszenarien für sensorbasiertes Monitoring kategorisiert und in Referenzanwendungen umgesetzt. Der Vortrag gibt einen Überblick über die abgeschlossene Planung. T2 - Jahrestreffen Verbund Aistec-Pro CY - Bonn, Germany DA - 17.09.2025 KW - SHM KW - Monitoring KW - Brückensicherheit KW - Aistec Pro PY - 2025 AN - OPUS4-64124 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen T1 - Evaluation of pile tip buckling based on large scale tests N2 - Der Vortrag zum zugehörigen Konferenzbeitrag beschreibt eine groß angelegte Feldtestkampagne mit 16 Rammversuchen, um das Risiko des plastischen Versagens der Pfahlspitzen besser zu verstehen Ein numerisches Modell mit transientem Bodenkontakt zeigt eine gute Übereinstimmung mit den Testergebnissen. Parametervariationen verdeutlichen, wie empfindlich die Pfahlreaktion auf Imperfektionen und Randbedingungen ist. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG) CY - Nantes, France DA - 09.06.2025 KW - Pile Tip Buckling KW - Monopile KW - Offshore Windenergy KW - Driving Refusal KW - Large Scale Test PY - 2025 AN - OPUS4-63391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis T1 - 3D spatial modelling of CPT data for probabilistic preliminary assessment of potential pile tip damage upon collision with boulders N2 - Tip damage of monopiles from boulder collisions during installation has emerged as a critical design issue, primarily due to the combination of the widespread use of large-diameter piles and the complexity of the ground conditions at the available sites. Recently, a framework relating potential pile tip damage to cone tip resistance from Cone Penetration Tests (CPTs) has been proposed in the literature. Gaussian processes are powerful stochastic models that enable probabilistic spatial interpolation of soil data at any location within a site. On this basis, this study utilizes sparse CPT data from a site in the North Sea, to first develop an efficient Gaussian process regression model, which is used to derive a three-dimensional (3D) probabilistic predictive map of the cone tip resistance. Assuming deterministic loading conditions and a factual collision with a boulder of pre-defined properties, the cone tip resistance predictive model is subsequently used for a probabilistic preliminary assessment of potential pile tip damage. Results of the analysis are realistic 3D probability maps of potential damage that aim to support engineering judgment and contribute towards cost-effective site investigation planning and offshore wind farm design. T2 - 5th International Symposium on Frontiers in Offshore Geotechnics (ISFOG) CY - Nantes, France DA - 09.06.2025 KW - CPT data KW - Gaussian process regression KW - Boulder impact KW - Preliminary pile tip damage assessment PY - 2025 AN - OPUS4-63444 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis T1 - CPT-based probabilistic analysis of monopile foundations considering spatial and transformation uncertainties N2 - This study utilizes cone penetration testing data data from a real offshore windfarm project in the North Sea and presents a method for incorporating both, statistical and spatial uncertainties, in a reliability-based assessment of monopile foundations. Initially, a Gaussian Process regression model is constructed to predict a 3D map of the cone tip resistance and the associated uncertainties in the predictions and the hyperparameters, leveraging Markov Chain Monte Carlo methods. The CPT-based prediction is combined with a correlation derived from data collected at a nearby site to predict the probability distribution of the friction angle at a test location, which is subsequently used to evaluate the probability of failure for a monopile foundation with a finite element model. T2 - 9th International Symposiumon Geotechnical Safety and Risk (ISGSR) CY - Oslo, Norway DA - 25.08.2025 KW - Monopile design KW - Cone Penetration Test KW - Gaussian process regression KW - Bayesian Inference PY - 2025 AN - OPUS4-64001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -