TY - CONF A1 - Auersch, Lutz T1 - Impacts between different drop masses and different targets in different scales N2 - The Federal Institute of Material Research and Testing has performed many impact tests from very small laboratory tests to very big “free-field” tests with heavy containers on stiff foundations. The first measurements have been done on a big foundation where it should be guaranteed that the foundation is rigid and the container is tested properly. Later on, a smaller drop test facility has been built on the ground inside an existing building. It had to be controlled by prediction and measurements that the drop test will not damage the building. Tests from different heights on soft, medium, and stiff targets have been done to find out rules which allow to identify acceptable and unacceptable drop tests. Later on, the biggest drop test facility has been built for masses up to 200 t. It was necessary for the design of the foundation to estimate the forces which oc-cur during the drop tests. In addititon, the acceptable tests should be selected and controlled by measurements where the impact duration is important. Dif-ferent sensors, accelerometers, accelerometers with mechanical filters, geo-phones (velocity transducers), strain gauges, and pressure cells have been ap-plied for these tasks. Signal transformations and model calculations have been used to check and understand the dynamic measurements. The simplest law is the conservation of the momentum which is a good approximation if the impact is short. If the soil under the foundation has an influence on the deceleration of the container, the maximum foundation velocity is lower than the simple esti-mation. T2 - 10th International Conference on Experimental Vibration Analysis for Civil Engineering Structures CY - Milano, Italy DA - 30.08.2023 KW - Drop test KW - Vibration measurements KW - Container loading KW - Foundation load PY - 2023 AN - OPUS4-58504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen T1 - Experimental Investigation on Buckling Behavior of soil-embedded Piles N2 - Monopile-Gründungen sind die mit Abstand am häufigsten verwendete Gründungskonstruktion für Offshore-Windenergieanlagen. Ein wesentliches Problem bei der Bemessung ist das lokale Beulen des Gründungspfahls, welches typischerweise im Bereich der Bettung auftritt. Aufgrund der Nichtlinearität der Bettungsrandbedingung sind klassische Bemessungsansätze nicht anwendbar, so dass der Bemessungsingenieur auf eine vollständig numerische Berechnung zurückgreifen muss. In diesem Vortrag wird eine experimentelle Versuchskampagne zur Erzeugung von Kalibrierungsdaten für solche numerischen Modelle vorgestellt. Eine ausführlichere Darstellung findet sich im gleichnamigen Artikel. T2 - EUROSTEEL 2023 CY - Amsterdam, Netherlands DA - 11.09.2023 KW - Wind KW - Wind Energy KW - Offshore KW - Shell Buckling KW - Soil-Structure-Interaction PY - 2023 AN - OPUS4-58365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Design challenges for Offshore wind-farms. From foundation mechanics to wind-farm aerodynamics N2 - This talk provides a brief introduction on general engineering design challenges for the offshore wind energy production. Some general features of the offshore wind-energy field from a civil engineering perspective are firstly presented, followed by a brief discussion of some of the main geomechanical issues for the foundation of the offshore turbines into the seabed. In the following part, an overview of relevant fluid-structure interactions and some options for an efficient numerical analysis are provided, where the hydromechanical Wave–Tower interaction is firstly discussed. Then, some general aspects of the windfarm aerodynamics are introduced. On the one hand, some modelling possibilities for the wake analysis of single turbines and turbine groups are discussed. And on the other hand the relevance of such analyses for a proper windfarm layout optimization is pointed out. In particular, this talk shows that: i) The performance and behavior of the turbine's foundation is often conditioned by the appearance of large deformations, fluid couplings and grain-scale phenomena, whereby specific physical testing (both in field and lab conditions) and ad-hoc simulation techniques can provide useful insights for design; ii) Numerical analysis of a turbine’s interaction with wind/waves is already affordable in engineering scales, while simplified models can already provide a useful insight into the windfarm aerodynamics. iii) Turbulent wake analysis is very relevant for the windfarm layout. T2 - Colloquium "Energy systems compared", Winter semester 22/23, Faculty of Physics CY - Duisburg, Germany DA - 24.01.2023 KW - Offshore wind-turbine foundations KW - Water-structure interaction KW - Wind-farm aerodynamics PY - 2023 AN - OPUS4-56888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines - 1st part: axial behavior T1 - Cimentaciones profundas para aerogeneradores marinos. 1a parte: Comportamiento axial N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The first lecture presents a brief introduction to the context and peculiarities of such foundations, and then focuses on the particular case of axially loaded piles. This part is most relevant for the relatively slender piles of the multi-pile substructures (i.e. jackets and tripods). A clear distinction between physical phenomenology and practical design is drawn here. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Online meeting DA - 17.03.2023 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods KW - Numerical modelling KW - Physical testing PY - 2023 AN - OPUS4-57176 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Large Monopiles: Experimental and numerical investigation of monopile tip buckling during installation as well as of local pile buckling under operational conditions N2 - The research project Verification of Buckling Assessment and Behaviour in Large Monopiles (VERBATIM) focuses on challenges arising due to the ongoing increase of dimensions of monopiles as foundation for offshore wind turbines. This project is focused on two main topics: - Monopile tip buckling during pile installation - Local buckling of embedded piles during operation It is known from previous investigations and experiences in practice that large deformations of a monopile tip during offshore installation works can occur. These large deformations initiated at the tip of the monopile are commonly referred to as “pile tip buckling”. Own research focuses on optimising monopile dimensions to reduce the cost of monopile foundations for offshore wind turbines while preventing pile tip buckling. Buckling of embedded cylindrical shells for offshore structures is a common engineering task. Structures can be analysed using standard software and have been done so in recent studies e.g., Gottschalk. However, the trend towards larger monopile and optimised structures has led to a fundamental need for better and verified models. A main challenge is the submodelling of the structure-soil-interaction. Developing such complex models is one main goal of the VERBATIM project. For both main topics model tests were performed at the laboratories of BAM and TU Berlin. These experimental results were used to verify related numerical models and simulations. T2 - WindEurope CY - Copenhagen, Denmark DA - 25.04.2023 KW - Monopiles KW - Tip Buckling KW - Pile Buckling KW - Foundations KW - Offshore KW - Windenergy PY - 2023 AN - OPUS4-57405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cuéllar, Pablo T1 - Deep foundations for offshore wind turbines - 2nd part: lateral behavior & advanced topics T1 - Cimentaciones profundas para aerogeneradores marinos. 2a parte: Comportamiento Lateral + Temática avanzada N2 - This presentation deals with the phenomenology and design of pile foundations for offshore wind turbines, and is divided into two lectures. The second lecture continues with the case of laterally loaded offshore piles, which bears most relevance for the case of the monopile foundations. Here again, a clear separation between physical reality and design methods is intended. Finally, the last part of the second lecture introduces several advanced topics which lie outside the classical design approaches, namely the hydromechanical coupling effects (i.e. the excess pore-pressure generation around the monopiles), the cyclic pile fatigue and the so-called pile setup (i.e. the time effects on the axial pile capacity). The relevance of the latter two topics is illustrated with experimental results from a field testing campaign on real large-scale piles. T2 - Masters course on Soil Mechanics and Geotechnical Engineering. Geotechnical Laboratory of CEDEX CY - Online meeting DA - 17.03.2023 KW - Pile foundations KW - Offshore wind turbines KW - Physical phenomenology KW - Design methods KW - Numerical modelling KW - Physical testing PY - 2023 AN - OPUS4-57178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Balscheit, Hagen T1 - Soil Embedded Piles - Reference Tests for Model Validation N2 - This presentation shows buckling tests on embedded piles conducted within the VERBATIM project. The generated data may serve as a valuable validation basis for numerical buckling design verification of Windenergy foundations in terms of the GMNIA concept. T2 - Buckling of Offshore Wind Energy Structures : 2-Day Buckling Colloquium CY - Berlin, Germany DA - 14.02.2024 KW - Wind Energy KW - Shell Buckling KW - Offshore Structures KW - GMNIA PY - 2024 AN - OPUS4-59536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eichner, Lukas T1 - LUKAS’ JACKET: A test structure for model and monitoring based lifetime management of offshore jacket support structures N2 - The goal of the experiments is to demonstrate that systems like three-dimensional jackets possess redundancies that, despite the reduced fatigue life of individual components, enable reliable operation if an appropriate maintenance concept is in place. In practice, individual potentially faulty components in the structure have been handled conservatively so far. To move away from this approach, methods and strategies in the field of life cycle management that enable economically optimal and reliable operation must be transferred from scientific research to practice. Experiments are the preferred method to establish the proof of concept. To realistically simulate the operational lifetime of a jacket structure through an experiment, cyclic loads must be applied to the structure to replicate typical fatigue processes. To ensure that the test structure is not a "disposable product" and can undergo multiple test cycles, the experimental concept includes system-level and component-level tests. The latter are conducted on removable joints. These elements at the nodes of the structure have been manufactured in multiple variations, both to potentially contain mentioned flaws and to undergo more load cycles individually than the main structure. Once the removable joint is sufficiently pre-damaged and thus the reduced remaining fatigue life is established, the element is inserted into the overall structure. The defined maintenance strategy is then implemented on the entire system. This strategy consists of structural health monitoring (SHM), inspections, and repairs. At defined intervals, cyclic loading is interrupted to apply dynamic loads. Using the installed monitoring system and coupled operational modal analysis (OMA), the modal parameters of the structure are determined, which can help identify potential system damage. Optimal sensor placement (OSP) can be determined based on a maximum value of information (VoI) across the entire pre-posterior predicted service life. For detailed investigations at the hotspots, inspections are conducted using non-destructive methods, among others. Overall global and local information about the structure's condition is gathered these methods, which are then incorporated into models describing the structure through Bayesian updating. This allows for initial system identification based on different system responses and later updating of the predicted parameters of analytical and numerical models. Utilizing the updated models, decisions regarding maintenance actions, such as further inspections or repairs, are made, which are subject to uncertainties. The probabilistic models enable a reliability- and risk-based maintenance strategy, where, for example, maximum failure rates can act as triggers for maintenance actions. These decisions are relevant for the planned duration of the simulated operational lifetime, as well as for potential lifetime extensions, which are currently of significant importance in practice. Optimizing the maintenance strategy for the operational lifetime of the structures with these methods will lead to a higher utility of the offshore wind farm. The work associated with the test structure encompasses a variety of topics (including fatigue, damage detection and identification, reliability, Bayesian updating, system identification, SHM, maintenance planning, decisions under uncertainties), which are integrated through corresponding models and methods. All these models have been and are being applied in the numerical accompaniment of the experiments. By applying them to a structure that includes the relevant locations and aspects of real-world structures, both well-functioning and suboptimal parts of the established framework will be revealed. T2 - 20th EAWE PhD Seminar on Wind Energy CY - Visby, Sweden DA - 23.09.2024 KW - Offshore Jacket Support Structure KW - Test Structure KW - Fatigue KW - Lifetime Management KW - Structural Health Monitoring PY - 2024 AN - OPUS4-61146 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Impulsvortrag: Ermüdungslebensdauerbewertung mittels Informationen aus Monitoring und Inspektionen N2 - Kontext: Ermüdungsbeanspruchte Tragstrukturen von Windenergieanlagen, Bestimmung der Ermüdungsbeanspruchungen und -zuverlässigkeit auf der Grundlage von Simulationen aus dem Design unter Berücksichtigung von Modellunsicherheiten, Aktualisierung der Ermüdungsbeanspruchungen und -zuverlässigkeit auf der Grundlage von globalen Monitoring- und lokalen Inspektionsinformationen aus dem Betrieb unter Berücksichtigung von Modell- und Messunsicherheiten T2 - 3. Verbundtreffen ReNEW CY - Berlin, Germany DA - 05.09.2024 KW - Modellunsicherheiten KW - Windenergie KW - Ermüdungslebensdauer KW - Tragstrukturen KW - Monitoring KW - Inspektionen PY - 2024 AN - OPUS4-61427 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kemmler, Samuel T1 - Simulating Piping Erosion in Suction Buckets N2 - This presentation gives an overview of the recent achievements in simulating piping erosion during the installation process of suction bucket foundations for offshore wind turbines. The physical correctness of the code is validated, and the simulation code's performance on the LUMI supercomputer is presented. The simulation results are compared to experimental data. T2 - Forschungsbesuch CY - Aix-en-Provence, France DA - 14.05.2024 KW - Offshore wind turbine KW - Suction bucket KW - Coupled fluid-particle simulation KW - High-performance computing PY - 2024 AN - OPUS4-60136 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Degener, Sebastian T1 - Load Identification and Damage Detection by a Digital Twin of a Bridge applying Bayesian Model Calibration N2 - A digital twin for decision making during the life cycle of civil infrastructure is a promising concept combining simulation models with corresponding structure-specific sensor data to support maintenance decisions or to investigate the reliability. The sensor data quality as well as the model quality of the digital twin, comprising on modeling assumptions and correct model parameters strongly influences the prognosis results. T2 - 10th European Workshop on Structural Health Monitoring (EWSHM 2024) CY - Potsdam, Germany DA - 10.06.2024 KW - Load identification KW - Damage detection KW - Digital Twin KW - Bayesian Model Calibration KW - Bridge model PY - 2024 AN - OPUS4-62186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zinas, Orestis A1 - Wilhelm, Sigrid T1 - CPT-based probabilistic design of monopile foundations N2 - This work was presented in the two-day workshop ‘Reliability-based methods in geotechnics’ organized by BAM and DGGT AK 2.15 in cooperation with the DGGT Academy. The presentation provides an overview of the sources of uncertainty in geotechnical analyses. A probabilistic 3D ground model of the cone-tip resistance from CPTs is developed utilizing sparse CPT data from a real offshore wind farm site in the North Sea. The predictive cone tip resistance model is used to derive a design property, such as the friction angle, using geotechnical transformation models. The friction angle profiles are then used to show an example of monopile design under uncertainty. T2 - Workshop: Einführung in die zuverlässigkeitsbasierte Bemessung in der Geotechnik 2024 CY - Berlin, Germany DA - 19.11.2024 KW - Geotechnical site-characterization KW - CPT KW - Spatial variability KW - Gaussian process regression KW - Design of monopiles KW - Offshore wind farms PY - 2024 AN - OPUS4-61716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald T1 - Zuverlässigkeitsbasierte Bemessung und Monte Carlo Simulation N2 - Am 19. und 20.11.2024 veranstaltete die BAM und der DGGT AK 2.15 „Zuverlässigkeitsbasierte Methoden in der Geotechnik“ in Zusammenarbeit mit der DGGT-Akademie einen zweitägigen Workshop zur Einführung in die zuverlässigkeitsbasierte Bemessung. Am ersten Tag wurden in einem Short Course die Grundlagen der Zuverlässigkeitsanalyse in der Geotechnik vermittelt, wobei den Teilnehmenden die Möglichkeit geboten wurde, unter Anleitung Aufgaben mit Hilfe geeigneter Software am PC selbstständig zu bearbeiten. In diesem Vortrag wurde die Grundlagen der zuverlässigkeitsbasierten Bemessung und die Monte Carlo Simulation zur Abschätzung der Versagenswahrscheinlichkeit dargestellt. T2 - 2. Workshop des DGGT AK 2.15 „Zuverlässigkeitsbasierte Methoden in der Geotechnik“ CY - Berlin, Germany DA - 19.11.2024 KW - Zuverlässigkeitsanalyse KW - Geotechnik KW - Monte Carlo Simulation PY - 2024 AN - OPUS4-61905 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Ronald A1 - Schwiersch, Niklas T1 - Betrieb und Planung - Ausgewählte Vorteile von Risikoanalysen im Ingenieur- und Wasserbau N2 - Am 19. und 20.11.2024 veranstaltete die BAM und der DGGT AK 2.15 „Zuverlässigkeitsbasierte Methoden in der Geotechnik“ in Zusammenarbeit mit der DGGT-Akademie einen zweitägigen Workshop zur Einführung in die zuverlässigkeitsbasierte Bemessung. Im Rahmen der Vortragsveranstaltung am zweiten Tag wurden zum einen die unterschiedlichen Sicherheits- und Bemessungsphilosophien nach dem bewährten Teilsicherheitskonzept sowie nach dem zuverlässigkeitsbasierten Konzept vorgestellt. Zum anderen werden verschiedene Anwendungen zuverlässigkeitsbasierter Verfahren aus der Ingenieurpraxis und Wissenschaft präsentiert. In diesem Vortrag wurden aus Sicht des Ingenieur- und Wasserbaus Vorteile von Risikoanalysen u. a. für die Planung von Inspektionszyklen, die Ursachenforschung im Versagensfall und die Konzeption von Hochwasserrisikomanagement-Maßnahmen präsentiert. T2 - 2. Workshop des DGGT AK 2.15 „Zuverlässigkeitsbasierte Methoden in der Geotechnik“ CY - Berlin, Germany DA - 19.11.2024 KW - Risikoanalyse KW - Offshore-Strukturen KW - Hochwasserschutz PY - 2024 AN - OPUS4-61906 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baier, Johanna A1 - Ziegert, Christof T1 - DIN 18940 für tragendes Lehmsteinmauerwerk – Potenzial und erste Anwendungserfahrungen N2 - Mit der Veröffentlichung der DIN 18940 Juni 2023 steht in Deutschland eine zeitgemäße Bemessungsgrundlage für tragendes Lehmmauerwerk zur Verfügung, die derzeit europaweit einmalig ist. Während nach bisherigen Vorschriften lediglich zweigeschossige Gebäude mit tragendem Lehmsteinmauerwerk realisierbar waren, ermöglicht die DIN 18940 nun den Einsatz von Lehmsteinmauerwerk in fünfgeschossigen, bis zu 13 m hohen Gebäuden. Das Bemessungskonzept der DIN 18940 lehnt sich an die Grundprinzipien der vereinfachten Berechnungsmethoden für unbewehrte Mauerwerksbauten nach DIN EN 1996-3/NA an und berücksichtigt dabei die materialspezifischen Eigenschaften von Lehmsteinmauerwerk. Anpassungen waren aufgrund der feuchteabhängigen Festigkeits- und Verformungskenngrößen sowie der im Vergleich zu herkömmlichem Mauerwerk geringen Steifigkeit erforderlich. Ein Vergleich mit konventionellem Mauerwerk aus Ziegeln, Porenbeton und Kalksandsteinen zeigt, dass Lehm hinsichtlich Tragfähigkeit und bauphysikalischen Eigenschaften im Bereich der Gebäudeklasse 1-4 konkurrenzfähig ist. Besonders die geringen CO2-Emissionen und die vollständige Rezyklierbarkeit machen Lehmsteinmauerwerk zu einer klimagerechten Alternative. Weiterhin werden erste Projekte vorgestellt, die nach DIN 18940 geplant wurden. Aus den Anwendungserfahrungen werden materialgerechte Entwurfsgrundsätze für Gebäude aus Lehmsteinmauerwerk formuliert. Abschließend zeigen Einblicke in laufende Forschung und zukünftige Entwicklung, wie das Potenzial von Lehmsteinmauerwerk weiter gesteigert werden kann. T2 - LEHM 2024 - 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Lehmmauerwerk KW - Ökobilanzierung KW - Normung PY - 2024 SP - 1 AN - OPUS4-62034 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiehle, Philipp T1 - Feuchteverhalten von Lehmsteinmauerwerk unter natürlichen Klimabedingungen N2 - Druckfestigkeit und Elastizitätsmodul von Lehmsteinmauerwerk nehmen mit steigendem Feuchtegehalt ab, weswegen die Mauerwerksdruckfestigkeit bei der Bemessung gemäß DIN 18940 in Abhängigkeit der maximal zu erwartenden Ausgleichsfeuchte abgemindert wird. Da bisher allerdings keine Messdaten zum Feuchtegehalt von Lehmsteinmauerwerk unter natürlichen Klimabedingungen vorliegen, stellen die normativen Grenzwerte lediglich eine konservative Abschätzung dar. Um die Feuchtegehalte von Lehmsteinmauerwerk und somit die Tragfähigkeit realitätsnah einschätzen zu können, wurden im Rahmen der vorliegenden Arbeit sowohl experimentelle als auch numerische Untersuchungen zum feuchtetechnischen Verhalten durchgeführt. Dabei wurden erstmalig magnetresonanzspektroskopische Untersuchungen an tragenden Lehmsteinen unterschiedlicher Herstellungsmethoden angewandt Weiterhin wurden Luftfeuchtesensoren in Lehmsteinmauerwerk eingebettet, um hygrische Langzeitfeuchtemessungen unter natürlichen Klimabedingungen durchzuführen. Auf Basis dieser Erkenntnisse wurde schließlich ein numerisches Modell kalibriert und Parameterstudien durchgeführt, um den unter realen Klimabedingungen tatsächlich auftretenden Feuchtegehalt im Lehmmauerwerk sowie dessen Verteilung über den Querschnitt einschätzen zu können und die normativen Grenzwerte zu überprüfen. Gezeigt wurde, dass die realitätsnahe instationäre Berechnung des Feuchtetransports mit üblichen hygrothermischen Simulationsprogrammen auf Basis einfacher feuchtetechnischer Kennwerte auch bei Lehmbaustoffen möglich ist. Der Einfluss des Quellens und Schwindens der enthaltenen Tonminerale und organischen Bestandteile wurde durch eine Modifikation bei der Ermittlung des Wasseraufnahmekoeffizienten explizit berücksichtigt und ist somit auch in den daraus abgeleiteten Transportkoeffizienten enthalten. Darüber hinaus wurde die Feuchtespeicherfunktion im überhygroskopischen Bereich auf Grundlage der Porenvolumenverteilung abgeschätzt. Die Approximation der Transportkoeffizienten und der Feuchtespeicherfunktion stellt dabei eine wesentliche Vereinfachung für Lehmbaustoffe dar, da ihre experimentelle Bestimmung aufgrund des Kontaktes mit Flüssigwasser kaum möglich ist. In Bezug auf das Feuchteverhalten üblicher Außenwandaufbauten von Wohnräumen konnte festgestellt werden, dass die Ausgleichsfeuchte im Lehmsteinmauerwerk stets unterhalb des in Nutzungsklasse 1 gemäß DIN 18940 zulässigen Grenzwertes von 65 % liegt. Je nach Putzsystem und Dämmstoff reduziert sich die Ausgleichsfeuchte auf Werte unter 60 %, wobei sich eine annähernd gleichmäßige Verteilung der Feuchte über den Mauerwerksquerschnitt hinweg einstellt. Bei Außenwänden von unbeheizten Räumen ergab sich eine maximale Ausgleichsfeuchte, die über weite Teile des Querschnitts unterhalb von 80 % lag. Der Ansatz einer maximalen Ausgleichsfeuchte von 90 % in Nutzungsklasse 2 ist folglich zu hoch angesetzt. Die zulässige Ausgleichsfeuchte bzw. der Umgebungsfeuchtefaktor in Nutzungsklasse 2 sollte dementsprechend angepasst werden. T2 - LEHM 2024 - 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Mauerwerk KW - Feuchte KW - Tragverhalten KW - Bemessung PY - 2024 AN - OPUS4-61904 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baier, Johanna T1 - Structural design of rammed earth considering the impact of moisture N2 - In March 2024, a research project was initiated at BAM with the aim of developing a design concept for rammed earth construction. It is based on experimental and numerical investigations into the mechanical load-bearing behaviour at both material and component level. As the mechanical parameters of earth building materials are strongly dependent on material moisture, the moisture behaviour of rammed earth is also being investigated in more detail. T2 - LEHM 2024 - 9. Internationale Fachtagung für Lehmbau CY - Weimar, Germany DA - 27.09.2024 KW - Rammed earth KW - Structral design KW - Material moisture PY - 2024 AN - OPUS4-62031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk T1 - Developing a guideline for SHM of road bridges in Germany N2 - In recent years, Structural Health Monitoring (SHM) has become a useful and increasingly widely used tool for supporting lifetime extensions of existing bridges with known structural deficiencies or indications of potentially critical damages or damage processes. At the same time, methods and tools are emerging, which enable monitoring-informed predictive maintenance of new and existing bridges based on digital twins. The monitoring process – starting from the definition of monitoring actions and ending with decisions based on monitoring outcomes – is complex and requires expertise in structural engineering, operation and maintenance of bridges, metrology, and data analytics. To support German road authorities, engineering consultancies, building contractors and other stakeholders of the bridge management, the Federal Highway Research Institute (BASt) has initiated the development of a new guideline for applying SHM as part of the management of road bridges. The guideline will present various use cases and for each identified use case, it will propose a proven monitoring scheme. In addition, the guideline will provide guidance on assessing the benefits of SHM as well as a common approach to managing monitoring data as a systematic basis for integrating monitoring data in the bridge management. This contribution discusses the motivation, objectives, and scope of the guideline, describes its use case centric structure and outlines the proposed data management. T2 - IABMAS 2024 CY - Kopenhagen, Danmark DA - 24.06.2024 KW - Guideline KW - Infrastructure KW - Structural health monitoring KW - Road bridges PY - 2024 AN - OPUS4-61395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Artinov, Antoni T1 - Modeling the Relationship between Weld Pool Dynamics and Centerline Solidification Cracking in High Power Laser Beam Welding N2 - The present work deals with the recently confirmed widening of the weld pool interface, known as a bulging effect, and its relevance in high power laser beam welding. A combined experimental and numerical approach is utilized to study the influence of the bulge on the hot cracking formation and the transport of alloying elements in the molten pool. A technique using a quartz glass, a direct-diode laser illumination, a high-speed camera, and two thermal imaging cameras is applied to visualize the weld pool geometry in the longitudinal section. The study examines the relevance of the bulging effect on both, partial and complete penetration, as well as for different sheet thicknesses ranging from 8 mm to 25 mm. The numerical analysis shows that the formation of a bulge region is highly dependent on the penetration depth and occurs above 10 mm penetration depth. The location of the bulge correlates strongly with the cracking location. The obtained experimental and numerical results reveal that the bulging effect increases the hot cracking susceptibility and limits the transfer of alloying elements from the top of the weld pool to the weld root. T2 - Gastvortrag an der Universität Innsbruck, Institut für Konstruktion und Materialwissenschaften CY - Innsbruck, Austria DA - 18.06.2023 KW - Laser beam welding KW - Centerline solidification cracking KW - Bulging KW - Numerical simulation PY - 2024 AN - OPUS4-60333 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramasetti, Eshwar Kumar A1 - Herrmann, Ralf A1 - Degener, Sebastian A1 - Baeßler, Matthias T1 - Development of generic AI models to predict the movement of vehicles on bridges N2 - For civil, mechanical, and aerospace structures to extend operation times and to remain in service, structural health monitoring (SHM) is vital. SHM is a method to examining and monitoring the dynamic behavior of essential constructions. Because of its versatility in detecting unfavorable structural changes and enhancing structural dependability and life cycle management, it has been extensively used in many engineering domains, especially in civil bridges. Due to the recent technical developments in sensors, high-speed internet, and cloud computing, data-driven approaches to structural health monitoring are gaining appeal. Since artificial intelligence (AI), especially in SHM, was introduced into civil engineering, these modern and promising methods have attracted significant research attention. In this work, a large dataset of acceleration time series using digital sensors was collected by installing a structural health monitoring (SHM) system on Nibelungen Bridge located in Worms, Germany. In this paper, a deep learning model is developed for accurate classification of different types of vehicle movement on the bridge from the data obtained from accelerometers. The neural network is trained with key features extracted from the acceleration dataset and classification accuracy of 98 % was achieved. T2 - SMAR 2024 - 7th International Conference on Smart Monitoring, Assessment and Rehabilitation of Civil Structures CY - Salerno, Italy DA - 04.09.2024 KW - Machine learning KW - Structural Health Monitoring (SHM) PY - 2024 AN - OPUS4-61375 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -