TY - JOUR A1 - Omar, Hassan A1 - Ahmadi, Shayan A1 - Szymoniak, Paulina A1 - Schönhals, Andreas T1 - Molecular Mobility of Thin Films of Poly (bisphenol-A carbonate) Capped and with one Free Surface: From Bulk-like Samples down to the Adsorbed Layer N2 - The molecular mobility of thin films of poly(bisphenol A carbonate) (PBAC) was systematically investigated using broadband dielectric spectroscopy, employing two distinct electrode configurations. First, films were prepared in a capped geometry between aluminum electrodes employing a crossed electrode capacitor (CEC) configuration, down to film thicknesses of 40 nm. The Vogel temperature, derived from the temperature dependence of relaxation rate of the α-relaxation, increases with decreasing film thickness characterized by an onset thickness. The onset thickness depends on the annealing conditions, with less intense annealing yielding a lower onset thickness. Additionally, a broadening of the β-relaxation peak was observed with decreasing thickness, attributed to the interaction of phenyl groups with thermally evaporated aluminum, resulting in a shift of certain relaxation modes to higher temperatures relative to the bulk material. A novel phenomenon, termed the slow Arrhenius process (SAP), was also identified in proximity to the α-relaxation temperature. For films with thicknesses below 40 nm, nanostructured electrodes (NSE) were utilized, incorporating nanostructured silica spacers to establish a free surface with air. This free surface causes an enhancement in the molecular mobility for the 40 nm sample, preserving the β-relaxation as a distinct peak. The α-relaxation was detectable in the dielectric loss down to 18 nm, shifting to higher temperatures as film thickness is decreased. Notably, the onset thickness for the increase in Vogel temperature was lower in the NSE configuration compared to the CEC setup, attributed to the presence of the polymer-air interface. KW - Thin polymer films PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623422 DO - https://doi.org/10.1039/d4sm01238k SN - 1744-6848 VL - 21 IS - 2 SP - 241 EP - 254 PB - RSC AN - OPUS4-62342 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Omar, Hassan A1 - Hiid, Gundula A1 - Szymoniak, Paulina A1 - Hertwig, Andreas A1 - Schönhals, Andreas T1 - Growth kinetics of the adsorbed layer of poly(bisphenol A carbonate) and its effect on the glass transition behavior in thin films N2 - The glass transition behavior of thin films of poly(bisphenol A carbonate) (PBAC) was studied employing ellipsometry. The glass transition temperature increases with the reduction of the film thickness. This result is attributed to the formation of an adsorbed layer with a reduced mobility compared to bulk PBAC. Therefore, for the first time, the growth kinetics of the adsorbed layer of PBAC was investigated, prepared by leaching samples from a 200 nm thin film which were annealed for several times at three different temperatures. The thickness of each prepared adsorbed layer was measured by multiple scans using atomic force microscopy (AFM). Additionally, an unannealed sample was measured. Comparison of the measurements of the unannealed and the annealed samples provides proof of a pre-growth regime for all annealing temperatures which was not observed for other polymers. For the lowest annealing temperature after the pre-growth stage only a growth regime with a linear time dependence is observed. For higher annealing temperatures the growth kinetics changes from a linear to a logarithmic growth regime at a critical time. At the longest annealing times the films showed signs of dewetting where segments of the adsorbed film were removed from the substrate (dewetting by desorption). The dependence of the surface roughness of the PBAC surface on annealing time also confirmed that the films annealed at highest temperatures for the longest times desorbed from the substrate. KW - Ultra thin polymer films PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-574531 DO - https://doi.org/10.1039/D3RA02020G SN - 2046-2069 VL - 13 IS - 21 SP - 14473 EP - 14483 PB - RSC Publishing CY - London AN - OPUS4-57453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kimiaei, E. A1 - Farooq, M. A1 - Szymoniak, Paulina A1 - Ahmadi, Shayan A1 - Babaeipour, S. A1 - Schönhals, Andreas A1 - Österberg, M. T1 - The role of lignin as interfacial compatibilizer in designing lignocellulosic-polyester composite films N2 - Advancing nanocomposites requires a deep understanding and careful design of nanoscale interfaces, as interfacial interactions and adhesion significantly influence the physical and mechanical properties of these materials. This study demonstrates the effectiveness of lignin nanoparticles (LNPs) as interfacial compatibilizer between hydrophilic cellulose nanofibrils (CNF) and a hydrophobic polyester, polycaprolactone (PCL). In this context, we conducted a detailed analysis of surface-to-bulk interactions in both wet and dry conditions using advanced techniques such as quartz crystal microbalance with dissipation (QCM-D), atomic force microscopy (AFM), water contact angle (WCA) measurements, broadband dielectric spectroscopy (BDS), and inverse gas chromatography (IGC). QCM-D was employed to quantify the adsorption behavior of LNPs on CNF and PCL surfaces, demonstrating LNPs’ capability to interact with both hydrophilic and hydrophobic phases, thereby enhancing composite material properties. LNPs showed extensive adsorption on a CNF model film (1186 ± 178 ng.cm−2) and a lower but still significant adsorption on a PCL model film (270 ± 64 ng.cm−2). In contrast, CNF adsorption on a PCL model film was the lowest, with a sensed mass of only 136 ± 35 ng.cm−2. These findings were further supported by comparing the morphology and wettability of the films before and after adsorption, using AFM and WCA analyses. Then, to gain insights into the molecular-level interactions and molecular mobility within the composite in dry state, BDS was employed. The BDS results showed that LNPs improved the dispersion of PCL within the CNF network. To further investigate the impact of LNPs on the composites’ interfacial properties, IGC was employed. This analysis showed that the composite films containing LNPs exhibited lower surface energy compared to those composed of only CNF and PCL. The presence of LNPs likely reduced the availability of surface hydroxyl groups, thus modifying the physicochemical properties of the interface. These changes were particularly evident in the heterogeneity of the surface energy profile, indicating that LNPs significantly altered the interfacial characteristics of the composite materials. Overall, these findings emphasize the necessity to control the interfaces between components for next-generation nanocomposite materials across diverse applications. KW - Lignin KW - Nanocomposites PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-615098 DO - https://doi.org/10.1016/j.jcis.2024.10.083 SN - 0021-9797 VL - 679 SP - 263 EP - 275 PB - Elsevier Inc. AN - OPUS4-61509 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Xu, Q. A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed A. A1 - Yang, Z. A1 - Wang, S. A1 - Gao, Y. A1 - Shang, J. A1 - Hunger, J. A1 - Aldiyarov, A. A1 - Schönhals, Andreas A1 - Ge, Y. A1 - Qi, Z. T1 - Molecular engineering of supramolecular polymer adhesive with confined water and a single crown ether N2 - Here, we report a water-induced supramolecular polymer built from confined structural water and an intrinsic amphiphilic macrocyclic self-assembly in a nanophase separated structure. The newly designed crown ether macrocycle, featuring strong hydrophilic hydrogen bonding receptor selenoxide and a synergistical hydrophobic selenium-substituted crown core, confines the structural water in a segregated, interdigitated architecture. Although water molecules typically freeze around 0 °C, the confined structural water in this supramolecular polymer remains in a liquid-like state down to 80 °C. Previous studies suggest that multiple crown ether units are needed to generate structural water. However, here, one unit is sufficient to control the formation and disappearance of structural water and consequent supramolecular polymerization. Typically, the DC conductivity of water shows Arrhenius temperature dependency (lnσDC ∝ 1/T). In contrast, this new crown unit maintains water in confined states, which exhibit a Vogel/Fulcher/Tammann behavior (lnσDC ∝ 1/(T-T0)) at temperatures above the glass transition temperature. Moreover, this water-induced supramolecular polymer exhibits remarkable adhesion properties to hydrophilic surfaces and maintains tough adhesion at low temperatures. These findings show how a single small macrocycle can govern the complex structure and functionality of water in supramolecular systems. KW - Supramolecular polymerization PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623631 DO - https://doi.org/10.1039/D4SC06771A SN - 2041-6539 VL - 16 SP - 1 EP - 9 PB - RSC AN - OPUS4-62363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Omar, Hassan A1 - Ahamadi, Shayan A1 - Hülagü, Deniz A1 - Hidde, Gundula A1 - Hertwig, Andreas A1 - Szymoniak, Paulina A1 - Schönhals, Andreas T1 - Investigations of the adsorbed layer of polysulfone: Influence of the thickness of the adsorbed layer on the glass transition of thin films N2 - This work studies the influence of the adsorbed layer on the glass transition of thin films of polysulfone. Therefore, the growth kinetics of the irreversibly adsorbed layer of polysulfone on silicon substrates was first investigated using the solvent leaching approach, and the thickness of the remaining layer was measured with atomic force microscopy. Annealing conditions before leaching were varied in temperature and time (0–336 h). The growth kinetics showed three distinct regions: a pre-growth step where it was assumed that phenyl rings align parallel to the substrate at the shortest annealing times, a linear growth region, and a crossover from linear to logarithmic growth observed at higher temperatures for the longest annealing times. No signs of desorption were observed, pointing to the formation of a strongly adsorbed layer. Second, the glass transition of thin polysulfone films was studied in dependence on the film thickness using spectroscopic ellipsometry. Three annealing conditions were compared: two with only a tightly bound layer formed in the linear growth regime and one with both tightly bound and loosely adsorbed layers formed in the logarithmic growth regime. The onset thickness and increase in the glass transition temperature increases with annealing time and temperature. These differences were attributed to the distinct conformations of the formed adsorbed layers. KW - Glass transition KW - Adsorbed Layer PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-607701 DO - https://doi.org/10.1063/5.0223415 SN - 0021-9606 VL - 161 IS - 5 SP - 1 EP - 12 PB - AIP Publishing AN - OPUS4-60770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Szymoniak, Paulina A1 - Juranyi, F. A1 - Kruteva, M. A1 - Zorn, R. A1 - Schönhals, Andreas T1 - Low-Frequency Vibrational Density of States of Nanophase- Separated Poly(n‑alkyl methacrylate)s: Confined Phonons and Relationship to Specific Heat N2 - This study investigates the low-frequency vibrational Density of states of nanophase-separated poly(n-alkyl methacrylate)s (PnMAs) and its relationship to specific heat. This system undergoes a nanophase separation for n > 1 in alkyl side chain-rich domains and a backbone-rich matrix. Using inelastic neutron scattering, the low-frequency vibrational density of states (Boson peak, BP) of PnMAs with varying alkyl side chain lengths (methyl, butyl, hexyl, and octyl) is measured. The results reveal that the BP shifts to higher frequencies with increasing side chain length reaching a maximum. This result indicates a counterbalance of confinement effects and the scattering of the matrix. The behavior of the Boson peak of the PnMAs is compared to other nanophase-separated systems, such as Janus-polynorbornenes and hexakis(n-alkyloxy)triphenylene discotic liquid crystals. The study also explores the connection between the BP and specific heat capacity, showing a linear relationship between the maximum frequency of the BP and the maximum temperature of the specific heat capacity anomaly. Moreover, from the measured vibrational density of states, the specific heat capacity is calculated and compared to experimental results. The comparison reveals qualitative agreement between the calculated and experimental data. These findings provide evidence for the sound wave interpretation of the Boson peak. KW - Inelastic Neutron Scattering PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636928 DO - https://doi.org/10.1021/acs.macromol.5c00898 SN - 1520-5835 SP - 1 EP - 12 PB - ACS Publications AN - OPUS4-63692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gawek, Marcel A1 - Szymoniak, Paulina A1 - Hülagü, Deniz A1 - Hertwig, Andreas A1 - Schönhals, Andreas T1 - Molecular Mobility of Thin Films and the Adsorbed Layer of Poly(2-vinylpyridine) N2 - The molecular dynamics of thin films and the adsorbed layer of poly(2-vinylpyridine) (P2VP) were investigated using broadband dielectric spectroscopy (BDS) and spectroscopic ellipsometry. Thin films of P2VP were prepared on silicon substrates and characterized to understand the influence of film thickness on the thermal glass transition temperature (Tg) and molecular mobility. The ellipsometric study revealed a decrease in Tg with decreasing film thickness, attributed to the enhanced mobility at the polymer/air interface. The adsorbed layer, prepared via the solvent leaching approach, exhibited a higher Tg compared to the bulk, indicating reduced molecular mobility due to strong polymer substrate interactions. The dielectric measurements were carried out in two different electrode configurations, crossed electrode capacitors (CEC) and nanostructured electrodes (NSE), where the latter allows for a free surface layer at the polymer/air interface. The relaxation rates of the α-relaxation measured in the CEC geometry collapse into one chart independent from the film thickness. For the thin films measured in the NSE arrangement the relaxation rates slow down with decreasing film thickness which was discussed as related to a stronger interaction of the P2VP segments with the native SiO2 at the surface of the silicon substrate compared to aluminum. It is worth to note that the effect of the enhanced mobility at the polymer/air interface is not observed in the dielectric measurements. BDS measurements in NSE geometry identified an additional relaxation process (α*-relaxation) in thin films, which was more pronounced in the adsorbed layer. This process is hypothesized to be related to molecular fluctuations within the adsorbed layer including the adsorption/desorption dynamics of segments or to a Slow Arrhenius Process (SAP) related to the equilibration dynamics deep in the glassy state. KW - Thin polymer films PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637181 DO - https://doi.org/10.1039/d5sm00539f SN - 1744-6848 SP - 1 EP - 12 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63718 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed A. A1 - Böhning, Martin A1 - De Souza, N. R. A1 - Juranyi, F. A1 - Zorn, R. A1 - Schönhals, Andreas T1 - Inelastic and Quasielastic Neutron Scattering on Polynorbornenes with Bulky Carbocyclic Side groups N2 - This study investigates the molecular mobility and vibrational properties of polynorbornenes with bulky carbocyclic side groups using inelastic and quasielastic neutron scattering techniques. The polymers, synthesized via metathesis and addition polymerization, exhibit varying degrees of microporosity, which ignificantly influences their gas separation performance. By inelastic neutron scattering experiments, it could be shown that all considered polymers have excess contributions to the low frequency vibrational density of states known as the Boson peak. The maximum frequency of the Boson peak correlates to the microporosity of the polymers. This correlation supports the sound wave interpretation of the Boson peak, suggesting that the microporous structure enhances the compressibility of the material at a microscopic length scale. The molecular mobility, particularly the methyl group rotation, was characterized using elastic scans and quasielastic neutron scattering. The study revealed a temperature dependent relaxation process, with the onset of molecular fluctuations observed around 200 K for the polymer containing methyl groups. For the polymer having no methyl groups only elastic scattering is observed. The methyl group rotation was analyzed in terms of a jump diffusion in a threefold potential with three equivalent energy minima. This leads to an almost correct description of the q dependence of the elastic incoherent scattering function when the number of hydrogen nuclei undergoing the methyl group rotation is considered. It was further evidenced that the fraction of methyl undergoing the methyl group rotation increases with increasing temperature. KW - Polymers of Intrinsic Microporosity KW - Neutron scattering PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630297 DO - https://doi.org/10.1016/j.polymer.2025.128358 SN - 1873-2291 VL - 328 SP - 241 PB - Elsevier Ltd. AN - OPUS4-63029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yildirim, Arda A1 - Haug, T. C. V. A1 - Fröba, M. A1 - Huber, P. A1 - Schönhals, Andreas T1 - Molecular fluctuations in mixed-metal MOF-74: influence of the metal composition N2 - A selected series of metal–organic frameworks M-MOF-74 (M = Mg, Co, Ni) and mixed metal MM-MOF-74 (Mg/Co or Mg/Ni) with different compositions of metal atoms have been prepared and further investigated by broadband dielectric spectroscopy (BDS) in a wide temperature range. The dielectric spectra show at least two relaxation processes. Process-A is observed only for the Ni-containing MOFs and is attributed to localized fluctuations of the metal oxide corners. Relaxation processes-B and -C are observed for all prepared MOFs, except that process-B is not observed for Ni-MOF-74. Large-angle fluctuations such as free rotations of the linkers can be excluded due to the structure of MOF-74, but small-angle fluctuations such as torsions are possible. According to numerical simulations carried out for MOF-74, process-B can be attributed to inward and outward fluctuations of the linkers relative to the pore center. Process-C is related to small-angle rotational fluctuations of the linker together with co-rotations of the metal nodes. The latter interpretation is supported by the dependence of the activation energy of the relaxation rate of process-C on the metal composition of the MOFs, which is discussed in terms of the bond lengths between the metal atoms and the linker which decrease in the sequence Mg, Co and Ni. KW - Metal Organic Frameworks PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639378 DO - https://doi.org/10.1039/d5ra05357a SN - 2046-2069 VL - 15 IS - 35 SP - 29109 EP - 29118 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolmangadi, Mohamed A. A1 - Raab, A. R. A1 - Szymoniak, Paulina A1 - Li, Z. A1 - Huber, P. A1 - Laschat, S. A1 - Schönhals, Andreas T1 - Molecular mobility and electrical conductivity of amino acid-based (DOPA) ionic liquid crystals in the bulk state and nanoconfinement N2 - This study explores the molecular mobility, phase behavior, and electrical conductivity of dihydroxyphenylalanine-based ionic liquid crystals (DOPAn, with alkyl side chains n = 12, 14, 16) featuring cyclic guanidiniumchloride headgroups, in both bulk and nanoconfined states. Using broadband dielectric spectroscopy, differential scanning calorimetry, and fast scanning calorimetry, the research uncovers a complex interplay between molecular structure, self-assembly, and molecular mobility. In bulk, DOPAn shows a phase sequence from plastic crystalline to hexagonal columnar and isotropic phases, driven by superdisc formation and columnar organization. Multiple relaxation processes are identified: localized side-chain dynamics (γ-relaxation), ionic headgroup or core motions (α1-relaxation), and cooperative alkyl domain fluctuations (α2-relaxation). Conductivity decreases with increasing side chain length. Under nanoconfinement in anodic aluminum oxide membranes, phase behavior changes: the Colh–Iso transition is suppressed, and a new α3-relaxation appears, linked to dynamics in an adsorbed interfacial layer. DC conductivity drops by up to four orders of magnitude due to confinement effects, altered molecular orientation, and phase transitions—especially the emergence of a nematic-like state in DOPA16. These findings highlight the importance of molecular design, pore geometry, and surface chemistry in tuning ionic liquid crystal properties for advanced applications in nanofluidics, ion transport, and responsive materials. KW - Ionic Liquid Crystals PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639657 DO - https://doi.org/10.1039/d5cp02406d SN - 1463-9084 SP - 1 EP - 17 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -