TY - CONF A1 - Gaal, Mate A1 - Ahmadzadeh, Majid A1 - Weise, Matthias T1 - Air-coupled ultrasonic transmission using thermoacoustic transmitters and optical microphones N2 - Background, Motivation and Objective Air-coupled ultrasonic transducers are usually applied for testing of some lightweight components. To increase the bandwidth or air-coupled testing systems and thus increase their application range, thermoacoustic transducers can be paired with optical microphones in a transmission mode. Thermoacoustic transmitters are based on the thermal excitation of sound waves, while optical microphones are based on laser interferometry and Fabri-Pérot etalon. We studied the spectrum and the efficiency of the transmission of an air gap using a thermoacoustic transmitter and an optical microphone. Statement of Contribution/Methods Thermoacoustic transmitters with an electrically conductive layer of indium tin oxide (ITO) on a curved quartz glass substrate were developed. Their sound field was measured using a commercially available optical microphone Eta450 Ultra based on Fabri-Perot etalon. The curvature and the conductive layer thickness of the thermoacoustic transmitter were systematically varied to investigate their impact on the sound field and the spectrum of the measured signal for frequencies up to 1 MHz. The transmitters were excited using rectangular burst signals with a varied width. We examined the influence of all parameters on the focusing, spectrum, and sensitivity. The directivity of the microphone was evaluated as well. Results/Discussion The focusing of the sound fields of all transmitters most strongly depends on the curvature radius of the substrate. The spectrum recorded in the focus of each transducer has several maxima and minima, as shown in the left-hand diagram, which are mostly a consequence of the irregularities of the microphone spectrum. These irregularities are visible also in the directivity diagram on the right, which was recorded by rotating the microphone. The 20 dB bandwidth of the measurement system covers the range up to about 1 MHz, depending strongly on the width of the excitation pulse (left-hand diagram). This highlights a key advantage of thermoacoustic transmitters: their spectral characteristics can be controlled through the excitation conditions, offering a potentially broader range of applications compared to conventional air-coupled transmitters. One promising example is localized ultrasound spectroscopy based on the detection of local resonances. T2 - IEEE International Ultrasonic Symposium CY - Utrecht, The Netherlands DA - 15.09.2025 KW - Air-coupled ultrasound KW - Thermoacoustic transmitter KW - Sound field PY - 2025 SP - 1 EP - 4 AN - OPUS4-64541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dittmann, Daniel A1 - Saal, L. A1 - Zietzschmann, F. A1 - Mai, M. A1 - Altmann, Korinna A1 - Al-Sabbagh, Dominik A1 - Ruhl, A. S. A1 - Jekel, M. A1 - Braun, U. T1 - Aktivkohlecharakterisierung als weiterer Schlüssel für Adsorptionsprognosen organischer Spurenstoffe in der vierten Reinigungsstufe N2 - In diesem Beitrag wird der Einfluss des Aktivkohleprodukts auf die Adsorption von Spurenstoffen aus Kläranlagenablauf gezeigt und diskutiert. Im zweiten Teil wird das Material Aktivkohle analytisch charakterisiert und die Eigenschaften systematisiert. Die gewonnenen Erkenntnisse werden mit Bezug zu Praxislösungen zusammengefasst. T2 - Wasser 2021 CY - Online meeting DA - 10.05.2021 KW - Aktivkohle KW - Thermogravimetrie KW - Zersetzungsgasanalyse KW - Proximatanalyse PY - 2021 SP - 373 EP - 378 AN - OPUS4-52740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph A1 - John, Elisabeth A1 - Firdous, Rafia A1 - Hirsch, Tamino A1 - Kaczmarek, Daria A1 - Ziesack, Kevin A1 - Buchwald, Anja A1 - Stephan, Dietmar A1 - Kruschwitz, Sabine ED - Ferrara, Liberato ED - Muciaccia, Giovanni ED - di Summa, Davide T1 - Beyond Theory: Pioneering AI-Driven Materials Design in the Sustainable Building Material Lab N2 - This work focuses on Artificial Intelligence (AI)-driven materials design, addressing the challenge of improving the sustainability of building materials amid complex formulations. These formulations involve various components, such as binders, additives, and recycled aggregates, necessitating a balance between environmental impact and performance. Traditional experimental methods often fall short in managing the complexity of material composition, hindering fast enough development of optimal solutions. Our research explores complex composition materials design through a comprehensive, comparative lab study between Data-Driven Design, using SLAMD - an open-source AI materials design tool, and traditional Design of Experiments (DOE). We aimed to develop a high-performance, alkali-activated material using secondary precursors, aiming for a compressive strength exceeding 100 MPa after 7-days. The findings reveal that AI-driven design outperforms DOE in development speed and material quality, successfully identif. T2 - 4 RILEM Spring Convention and Conference on advanced construction materials and processes for a carbon neutral society 2024 CY - Milano, Italy DA - 07.04.2024 KW - Secondary Raw Materials KW - Data-Driven Design KW - Sequential Learning KW - Design of Experiments KW - Alkali-Activated Binder PY - 2024 SN - 978-3-03170281-5 DO - https://doi.org/10.1007/978-3-031-70281-5_31 SN - 2211-0852 VL - 2 SP - 274 EP - 282 PB - Springer AN - OPUS4-61662 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid (HNO3) on HDPE jerrycans – comparison of outdoor and lab test N2 - A damaging action of HNO3-55% only occurs in combination with its decomposition into nitrous gases, which can be caused by UV radiation. In a laboratory test, transparent HDPE jerrycans have been exposed to both UV radiation and 55 wt-% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The respective damages are compared with FTIR spectroscopy in ATR and HT-gel permeation chromatography (GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. The gradual increase in oxidative damage shows the good reproducibility of the lab exposure. The decomposition of nitric acid into nitrous gases by UV radiation – as well as the jerrycan oxidation – is also observed at lower HNO3 concentration (28 wt- %). Similar results are obtained after outdoor tests. Again, the damage occurs only after combined exposure, in contrast to the exposures to UV only and to HNO3 only, which were conducted in parallel. Outdoor exposures are most readily accepted as they represent possible end-use conditions. However, the reproducibility of these exposures is poor due to the large temporal variations in weather. There are also several safety risks, which is why the number of replicates remains limited. Since the outdoor and lab exposure tests show the same qualitative results, it is appropriate to conduct systematic studies in the laboratory. After 6 days of lab exposure, the oxidation damage is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. It should be noted that this amount can also occur in two sunny weeks. T2 - 24th iapri World Packaging Conference CY - Valencia, Spain DA - 17.06.2024 KW - Ppolyethylene KW - UV exposure KW - Nitric acid KW - Oxidation PY - 2024 VL - 2 SP - 30 EP - 37 PB - ITENE AN - OPUS4-60414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Kömmling, Anja A1 - Böhning, Martin A1 - Silbernagl, Dorothee T1 - Comparison of ageing behavior of O-ring seals under hydrogen and air N2 - Elastomeric seals are essential components in the infrastructure which prevent leakage of gas and ensure proper function of technical devices and are therefore highly safety relevant. For proper function a remaining resilience and tolerance to pressure changes is required. The ageing of elastomers is an undesirable but inevitable process leading to a limited lifetime of rubber products such as seals. Independent of the application, as e.g. automotive, piping or container applications, a long lifetime or at least a timely exchange of a seal before occurrence of critical failure is desired. Hydrogen is a key element for the energy turnaround and therefore the compatibility of seals with hydrogen is essential. In addition to the effect of hydrogen uptake and release, which might also cause destructive effects such as rapid gas decompression, ageing at high temperature under hydrogen atmosphere is of interest too. Most of the existing work is addressing the performance of new materials and comprises only very limited investigations concerning long-term use and the behaviour of aged materials in contact with hydrogen. As ageing can lead to substantial changes of material properties, it must be evaluated whether these changes are beneficial or deteriorating for the component function. In this work we present and compare results of the characterization of three sealing materials (EPDM, HNBR, FKM) after ageing at high temperature under hydrogen and air. Despite the common assumption that ageing under hydrogen atmosphere should be less severe for the material in comparison to air ageing, this is not the case for every material. T2 - ASME PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Aging KW - Seal KW - Compression set KW - Atomic force microscopy PY - 2025 SP - 1 EP - 7 AN - OPUS4-63889 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cornelsen Sampaio Kling, I. A1 - Pauw, Brian Richard A1 - Agudo Jácome, Leonardo A1 - Archanjo, B. S. A1 - Simão, R. A. T1 - Development and characterization of starch film and the incorporation of silver nanoparticles N2 - Starch is one of the biopolymers being used for bioplastic synthesis. For production, starch can be combined with different plasticizers, starches from different plant sources and even with nanomaterials to improve or to add film properties. The challenge of adding these, e.g. in the form of silver nanoparticles (AgNp) is to determine the concentration so as to avoid impairing the properties of the film, agglomeration or altering the visual characteristics of the film. In this study, a starch film synthesis route and the incorporation of silver nanoparticles has been proposed in order not to alter the properties of the film while maintaining the transparency and a clear colour of the starch film. The results showed that the proposed synthesis route is promising, efficient, reproducible, fast and the film has good mechanical properties. T2 - Semana MetalMat & Painal PEMM 2020 CY - Online meeting DA - 23.11.2020 KW - Biofilm KW - Silver nanoparticle KW - Starch KW - Starch nanoparticle PY - 2020 SP - 1 EP - 2 AN - OPUS4-51940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ermilova, Elena A1 - Hertwig, Andreas A1 - Döhring, Thorsten A1 - Stanik, Eva A1 - Cotroneo, Vincenzo A1 - Gibertini, Eugenio T1 - Ellipsometrical characterization of poly-dopamine layers considered for technical applications N2 - Although the organic molecule dopamine (3,4-dihydroxyphenethylamine) is commonly known as the “hormone of happiness”, thin films of poly-dopamine also have interesting technical properties. When produced by dip coating, the self-organizing layers grow in a reproducible thickness of single or multiple molecule monolayers of a few nanometer thickness only. In this work, we introduce a method of determining the layer thickness of poly-dopamine on mirrors for astronomical X-ray telescopes. This work is based on spectroscopic ellipsometry measurements and involves the development of an optical model for the poly-dopamine layers including the dielectric function. Thereby the complex refractive index of the produced layers was determined, covering the range from the ultraviolet to the near infrared spectral region. These measurement results and the corresponding technical challenges are presented in this contribution. Furthermore, an outlook to potential technical applications of this interesting material is given and poly-dopamine layers will make scientist and engineers hopefully happy as an innovative and fascinating technical solution for the future. T2 - SPIE PHOTONICS EUROPE CY - Strasbourg. France DA - 08.04.2024 KW - Polydopamine KW - Thin Solid Layers KW - X-ray optics KW - Spectroscopic Ellipsometry PY - 2024 SN - 978-1-5106-7344-1 DO - https://doi.org/10.1117/12.3015281 VL - 13013 SP - 1 EP - 8 PB - SPIE digital library AN - OPUS4-60954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Legall, Herbert A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - Emission of X-rays during ultrashort pulse laser processing N2 - Ultrashort pulse laser materials processing can be accompanied by the production of X-rays. Small doses per laser pulse can accumulate to significant dose rates at high laser pulse repetition rates which may exceed the permitted X-ray limits for human exposure. Consequently, a proper radiation shielding must be considered in laser machining. A brief overview of the current state of the art in the field of undesired generation of X-ray radiation during ultrashort pulse laser material processing in air is presented. T2 - Lasers in Manufacturing Conference 2021 CY - Online meeting DA - 21.06.2021 KW - Ultra-short pulse laser processing KW - Laser-induced X-ray emission KW - Radiation protection PY - 2021 SP - 1 EP - 5 AN - OPUS4-53866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Oliveira Guilherme Buzanich, Ana A1 - Radtke, Martin A1 - Emmerling, Franziska ED - Rogge, Andreas ED - Meng, Birgit T1 - Exploring new materials for Green Intelligent Building - How can our BAMline help? N2 - In the scope of exploring and characterizing new materials related to Green Intelligent Building (GIB), we will provide an overview of the X-ray spectroscopy and diffraction analytical methods available at the BAMline /1/. and Myspot beamlines. These are two universal beamlines at the Berlin Synchrotron BESSY-II, where BAM has access and supervision role. Overarching electronic and structural properties at different time and length scales, such measurements enable a real-time characterization of materials properties. We will show-case in situ and ex situ deterioration and hydration studies on cement-based constructure materials. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - BAMline KW - Scope of exploring KW - Green intelligent building PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612882 SN - 978-3-9818564-7-7 SP - 30 EP - 36 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61288 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Florian, Camilo A1 - Deziel, J.-L. A1 - Kirner, Sabrina V. A1 - Siegel, J. A1 - Bonse, Jörn T1 - Femtosecond laser-induced oxidation in the formation of periodic surface structures N2 - Micro- and nanostructuring with laser-induced periodic surface structures (LIPSS) has been demonstrated to be feasible in a wide variety of materials including metals, semiconductors and dielectrics. Suitable processing regimes for flat, curved and complex surfaces have been identified for many materials, allowing the generation of diverse applications in fields such as optics, tribology and medicine, to name a few. A common side effect when producing such structures in air environment is the formation of a thin surface oxide layer in the laser irradiated areas. Previous studies have shown that oxidation plays an important role in the tribological performance for which the structures where created, and very recently it has been shown that the laser-induced oxide graded layers may contribute to the formation of a new type of embedded low-spatial frequency LIPSS (LSFL) with annomalous orientation parallel to the laser polarization, in addition to the appearance of the well-known high-spatial frequency LIPSS (HSFL) at the surface. In this contribution, we explore this effect experimentally for chromium nitride (CrN) irradiated with femtosecond laser pulses and compare the findings to finite-difference time-domain (FDTD) simulations of the intensity distributions at different depth positions. T2 - 2021 Conference on Lasers and Electro-Optics/Europe – European Quantum Electronics Virtual Conferences CY - Munich, Germany DA - 21.06.2021 KW - Femtosecond laser ablation KW - Finite-difference time-domain calculations KW - Laser-induced periodic surface structures (LIPSS) KW - Surface oxidation PY - 2021 SN - 978-1-6654-1876-8 DO - https://doi.org/10.1109/CLEO/Europe-EQEC52157.2021.9542774 VL - 2021 SP - 1 PB - Institute of Electrical and Electronics Engineers (IEEE) CY - Piscataway, NJ, USA AN - OPUS4-53457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -