TY - JOUR
A1 - Vogel, Christian
A1 - Hoffmann, Marie
A1 - Krüger, O.
A1 - Murzin, V.
A1 - Caliebe, W.
A1 - Adam, Christian
T1 - Chromium (VI) in phosphorus fertilizers determined with the diffusive gradients in thin-films (DGT) technique
N2 - Phosphorus (P) fertilizers from secondary resources became increasingly important in the last years. However, these novel P-fertilizers can also contain toxic pollutants such as chromium in its hexavalent state (Cr(VI)). This hazardous form of chromium is therefore regulated with low limit values for agricultural products even though the correct determination of Cr(VI) in these fertilizers may be hampered by redox processes, leading to false results. Thus, we applied the novel diffusive gradients in thin-films (DGT) technique for Cr(VI) in fertilizers and compared the results with the standard wet chemical extraction method (German norm DIN EN 15192) and Cr K-edge X-ray Absorption near-edge structure (XANES) spectroscopy. We determined an overall good correlation between the wet chemical extraction and the DGT method. DGT was very sensitive and for most tested materials selective for the analysis of Cr(VI) in P-fertilizers. However, hardly soluble Cr(VI) compounds cannot be detected with the DGT method since only mobile Cr(VI) is analyzed. Furthermore, Cr K-edge XANES spectroscopy showed that the DGT binding layer also adsorbs small amounts of mobile Cr(III) so that Cr(VI) values are overestimated. Since certain types of the P fertilizers contain mobile Cr(III) or partly immobile Cr(VI), it is necessary to optimize the DGT binding layers to avoid aforementioned over- or underestimation. Furthermore, our investigations showed that the Cr K-edge XANES spectroscopy technique is unsuitable to determine small amounts of Cr(VI) in fertilizers (below approx. 1% of Cr(VI) in relation to total Cr).
KW - Phosphorus fertilizer
KW - Sewage sludge ash
KW - Diffusive Gradients in thin films (DGT)
KW - Chemical extraction
KW - XANES spectroscopy
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509578
DO - https://doi.org/10.1007/s11356-020-08761-w
SN - 0944-1344
VL - 27
SP - 24320
EP - 24328
PB - Springer
AN - OPUS4-50957
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Herzel, Hannes
A1 - Aydin, Zeynep
A1 - Adam, Christian
T1 - Crystalline phase analysis and phosphorus availability after thermochemical treatment of sewage sludge ash with sodium and potassium sulfates for fertilizer production
N2 - Phosphorus rich sewage sludge ash is a promising source to produce phosphorus recycling fertilizer. However, the low plant availability of phosphorus in these ashes makes a treatment necessary. A thermochemical treatment (800–1000 °C) with alkali additives transforms poorly plant available phosphorus phases to highly plant available calcium alkali Phosphates (Ca,Mg)(Na,K)PO4. In this study, we investigate the use of K2SO4 as additive to produce a phosphorus potassium fertilizer in laboratory-scale experiments (crucible). Pure K2SO4 is not suitable as high reaction temperatures are required due to the high melting point of K2SO4.
To overcome this barrier, we carried out series of experiments with mixtures of K2SO4 and Na2SO4 resulting in a lower economically feasible reaction temperature (900–1000 °C). In this way, the produced phosphorus potassium fertilizers (8.4 wt.% K, 7.6 wt.% P) was highly plant available for phosphorus indicated by complete extractable phosphorus in neutral ammonium citrate solution. The added potassium is, in contrast to sodium, preferably incorporated into silicates instead of phosphorus phases. Thus, the highly extractable phase (Ca,Mg)(Na,K)PO4 in the thermochemical products contain less potassium than expected. This preferred incorporation is confirmed by a pilot-scale trial (rotary kiln) and thermodynamic calculation.
KW - Phosphorus recovery
KW - Recycling fertilizer
KW - Calcium alkali phosphate
KW - Silicate
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-536276
DO - https://doi.org/10.1007/s10163-021-01288-3
SN - 1611-8227
IS - 23
SP - 2242
EP - 2254
PB - Springer
AN - OPUS4-53627
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Raniro, H.R.
A1 - Soares, T.de M.
A1 - Adam, Christian
A1 - Pavinato, P.S.
T1 - Waste-derived fertilizers can increase phosphorus uptake by sugarcane and availability in a tropical soil
N2 - The use of highly water-soluble phosphorus (P) fertilizers can lead to P fixation in the soil, reducing fertilization efficiency. Waste-derived, low water-solubility sources can potentially increase sugarcane’s P uptake compared to triple superphosphate by reducing adsorption to the soil.
Aims:We aimed to test struvite, hazenite, and AshDec® for their agronomic potential as recycled fertilizers for sugarcane production in a typical tropical soil.We hypothesize that these sources can reduce P fixation in the soil, increasing its availability and sugarcane’s absorption.
Methods: In a greenhouse pot experiment, two consecutive sugarcane cycles, 90 days each, were conducted in a Ferralsol. The recovered sources struvite, hazenite, AshDec®, and the conventional triple superphosphate were mixed in the soil in three P doses (30, 60, and 90 mg kg–1), aside a control (nil-P). At both harvests, sugarcane number of sprouts, plant height, stem diameter, dry mass yield, shoot phosphorus, and soil P fractionation were investigated.
Results: At 90 days, struvite and hazenite performed better for dry mass yield (70.7 and 68.3 g pot–1, respectively) than AshDec® and triple superphosphate (59.8 and 57.4 g pot–1, respectively) and for shoot P, with 98.1, 91.6, 75.6, and 66.3 mg pot–1, respectively. At 180 days, struvite outperformed all treatments for dry mass yield (95.3 g pot–1) and AshDec® (75.5 mg pot–1) for shoot P. Struvite was 38% and hazenite 21% more efficient than triple superphosphate in P uptake, while AshDec® was 6% less efficient. Soil had higher labile P under struvite, hazenite, and AshDec® than triple superphosphate by the end of the first cycle, while only the later increased nonlabile P by the end of the experiment (180 days).
Conclusions:Waste-derived P sources were more efficient in supplying P for sugarcane and delivering labile P in 180 days than triple superphosphate.
KW - AshDec
KW - Hazenite
KW - P-efficiency
KW - Recycled sources
KW - Struvite
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-544216
DO - https://doi.org/10.1002/jpln.202100410
SN - 1436-8730
SP - 1
EP - 12
PB - Wiley-VCH GmbH
AN - OPUS4-54421
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Schraut, Katharina
A1 - Kargl, F.
A1 - Adam, Christian
A1 - Ivashko, O.
T1 - In situ synchrotron XRD measurements during solidification of a melt in the CaO–SiO2 system using an aerodynamic levitation system
N2 - Phase formation and evolution was investigated in the CaO–SiO2 system in the range of 70–80 mol% CaO. The samples were container-less processed in an aerodynamic levitation system and crystallization was followed in situ by synchrotron x-ray diffraction at the beamline P21.1 at the German electron synchrotron (DESY). Modification changes of di- and tricalcium silicate were observed and occurred at lower temperatures than under equilibrium conditions. Despite deep sample undercooling, no metastable phase formation was observed within the measurement timescale of 1 s. For the given cooling rates ranging from 300 K s−1 to about 1 K s−1, no decomposition of tricalcium silicate was observed. No differences in phase evolution were observed between reducing and oxidizing conditions imposed by the levitation gas (Ar and Ar + O2). We demonstrate that this setup has great potential to follow crystallization in refractory oxide liquids in situ. For sub-second primary phase formation faster detection and for polymorph detection adjustments in resolution have to be implemented.
KW - Aerodynamic levitation
KW - Calcium silicate
KW - Phase formation
KW - Oxide melts
KW - In situ synchrotron x-ray diffraction
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526952
DO - https://doi.org/10.1088/1361-648X/abf7e1
VL - 33
IS - 26
SP - 264003 (12pp)
PB - IOP Publishing
AN - OPUS4-52695
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Sichler, Theresa Constanze
A1 - Adam, Christian
A1 - Barjenbruch, M.
A1 - Montag, D.
A1 - Mauch, Tatjana
A1 - Sommerfeld, Thomas
A1 - Ehm, J.H.
T1 - Variation of the element composition of municipal sewage sludges in the context of new regulations on phosphorus recovery in Germany
N2 - Phosphorus (P) recovery is obligatory for all sewage sludges with more than 20 g P/kg dry matter (DM) from 2029 in Germany. Nine wastewater treatment plants (WWTPs) were chosen to investigate variations of phosphorus contents and other parameters in sewage sludge over the year. Monthly sewage sludge samples from each WWTP were analyzed for phosphorus and other matrix elements (C, N, H, Ca, Fe, Al, etc.), for several trace elements (As, Cr, Mo, Ni, Pb, Sn) and loss of ignition. Among the nine WWTPs, there are four which have phosphorus contents both above and below the recovery limit of 20 g/kg DM along the year. Considering the average phosphorus content over the year, only one of them is below the limit. Compared to other matrix elements and parameters, phosphorus fuctuations are low with an average of 7% over all nine WWTPs. In total, only hydrogen and carbon are more constant in the sludge.
In several WWTPs with chemical phosphorus elimination, phosphorus fuctuations showed similar courses like iron and/or aluminum. WWTPs with chamber flter presses rather showed dilution efects of calcium dosage. As result of this study, monthly phosphorus measurement is highly recommended to determine whether a WWTP is below the
20 g/kg DM limit.
KW - Sewage sludge
KW - Phosphorus recovery
KW - Wastewater
KW - Phosphorus elimination
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557499
DO - https://doi.org/10.1186/s12302-022-00658-4
SN - 2190-4707
VL - 34
IS - 1
SP - 1
EP - 12
PB - Springer Nature
CY - Berlin
AN - OPUS4-55749
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Sichler, Theresa Constanze
A1 - Adam, Christian
A1 - Becker, Roland
A1 - Sauer, Andreas
A1 - Ostermann, Markus
A1 - Barjenbruch, M.
T1 - Phosphorus determination in sewage sludge: comparison of different aqua regia digestion methods and ICP-OES, ICP-MS and photometric determination
N2 - Phosphorus recycling from sewage sludge will be obligatory in Germany from 2029. Phosphorus content determination in sewage sludge is crucial to assess the prescribed recycling rates. Currently, German law regards sample preparation using aqua regia digestion in a microwave or under reflux conditions as well as instrumental phosphorus determination by ICP-OES, ICP-MS, or photometric determination with ammonium molybdate as equivalent. However, it is questionable whether these methods are indeed equivalent regarding phosphorus quantification in sludges near the limit of 20 g/kg for mandatory recycling. To answer this question, 15 sewage sludges of 11 different wastewater treatment plants were investigated with all permitted method (digestion and measurement) combinations. Moreover, one sewage sludge was also examined in an interlaboratory comparison (ILC) with 28 participants. This study shows that the above-mentioned methods differ in some cases significantly but across all method combinations and sludges, phosphorus recovery was between 80 and 121% after normalization to the grand mean (average of 15 sludges between 85 and 111%). The ILC and the examination of 15 sludges produced largely similar results. There is a tendency to higher phosphorus recovery after microwave digestion compared to reflux digestion and ICP-OES measurements determine higher phosphorus contents than ICP-MS and photometric phosphorus determination. As a result, the authors recommend ICP-OES determination of phosphorus in sewage sludge after microwave digestion.
KW - Sewage sludge
KW - ICP-OES
KW - Phosphous recovery
KW - ICP-MS
KW - Photometric P determination
KW - Interlaboratory comparison
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-558869
DO - https://doi.org/10.1186/s12302-022-00677-1
VL - 34
IS - 99
SP - 1
EP - 14
PB - Springer
AN - OPUS4-55886
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Dombinov, V.
A1 - Herzel, Hannes
A1 - Meiller, M.
A1 - Müller, F.
A1 - Willbold, S.
A1 - Zang, J. W.
A1 - da Fonseca-Zang, W. A.
A1 - Adam, Christian
A1 - Klose, H.
A1 - Poorter, H.
A1 - Jablonowski, N. D.
A1 - Schrey, S. D.
T1 - Sugarcane bagasse ash as fertilizer for soybeans: Effects of added residues on ash composition, mineralogy, phosphorus extractability and plant availability
N2 - Sugarcane bagasse is commonly combusted to generate energy. Unfortunately, recycling strategies rarely consider the resulting ash as a potential fertilizer. To evaluate this recycling strategy for a sustainable circular economy, we characterized bagasse ash as a fertilizer and measured the effects of co-gasification and co-combustion of bagasse with either chicken manure or sewage sludge: on the phosphorus (P) mass fraction, P-extractability, and mineral P phases. Furthermore, we investigated the ashes as fertilizer for soybeans under greenhouse conditions. All methods in combination are reliable indicators helping to assess and predict P availability from ashes to soybeans. The fertilizer efficiency of pure bagasse ash increased with the ash amount supplied to the substrate. Nevertheless, it was not as effective as fertilization with triple-superphosphate and K2SO4, which we attributed to lower P availability. Co-gasification and co-combustion increased the P mass fraction in all bagasse-based ashes, but its extractability and availability to soybeans increased only when co-processed with chicken manure, because it enabled the formation of readily available Ca-alkali phosphates. Therefore, we recommend co-combusting biomass with alkali-rich residues to increase the availability of P from the ash to plants.
KW - Combustion and gasification
KW - Phosphate extractability and availability
KW - X-ray diffraction (XRD)
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567632
DO - https://doi.org/10.3389/fpls.2022.1041924
SN - 1664-462X
VL - 13
SP - 1
EP - 13
PB - Frontiers Media
CY - Lausanne
AN - OPUS4-56763
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Herzel, Hannes
A1 - Grevel, K.-D.
A1 - Emmerling, Franziska
A1 - Dachs, E.
A1 - Benisek, A.
A1 - Adam, Christian
A1 - Majzlan, J.
T1 - Thermodynamic properties of calcium alkali phosphates Ca(Na,K)PO4
N2 - Calcium alkali phosphates Ca(Na,K)PO4 are main constituents of bioceramics and thermochemically produced phosphorus fertilizers because of their bioavailability. Sparse thermodynamic data are available for the endmembers CaNaPO4 and CaKPO4. In this work, the missing data were determined for the low-temperature phase modifications of the endmembers CaNaPO4 and CaKPO4 and three intermediate Ca(Na,K)PO4 compositions. Standard enthalpy of formation ranges from - 2018.3 ± 2.2 kJ mol-1 to - 2030.5 ± 2.1 kJ mol-1 and standard entropy from 137.2 ± 1.0 J mol-1 K-1 to 148.6 ± 1.0 J mol-1 K-1 from sodium endmember b-CaNaPO4 to potassium endmember b0-CaKPO4.
Thermodynamic functions are calculated up to 1400 K for endmembers and the sodium-rich intermediate phase b-Ca(Na0.93K0.07)PO4. Functions above 640 K are extrapolated because of the phase transition from low- to high-temperature phase. Impurities in the synthesized intermediate phases c-Ca(Na0.4K0.6)PO4 and c-Ca Na0.35K0.65)PO4 and one additional phase transition around 500 K impeded the determination of high-temperature thermodynamic functions. In general, data for phase transition temperatures agree with the previously reported phase diagrams.
KW - Formation enthalpy
KW - Heat capacity
KW - Phase transformation
KW - Bioceramics
KW - Phosphorus fertilizer
KW - Entropy
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507640
DO - https://doi.org/10.1007/s10853-020-04615-5
VL - 55
SP - 8477
EP - 8490
PB - Springer
AN - OPUS4-50764
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -