TY - JOUR A1 - Kalbe, Ute A1 - Simon, Franz-Georg T1 - Potential use of incineration bottom ash in construction – Evaluation of the environmental impact N2 - Knowledge of the long-term leaching behavior of potentially harmful substances is crucial for the assessment of the environmental compatibility of reusing municipal solid-waste incineration bottom ash (MSWI BA) in construction, i.e., as a road base layer. BA fractions obtained from wet-processing aiming at the improvement of environmental quality were used to investigate the mobility of relevant substances. Eluates from laboratory-scaled leaching procedures (column percolation and lysimeters) were analyzed to learn about the long-term release of substances. Unsaturated conditions and artificial rainwater (AR) were used in the lysimeter tests to simulate field conditions. In addition, batch test eluates were generated at usual liquid-to-solid ratios (L/S) for compliance testing purposes. A variety of cations and anions was measured in the eluates. The wet treatment reduces the leaching of chloride and particularly sulfate by more than 60%. The release of typical contaminants for the treated MSWI BA such as the heavy metals Cu and Cr was well below 1% in the conducted leaching tests. An increase in the Sb concentration observed in the lysimeter experiments starting at L/S 0.75 L/kg and in the column experiment at L/S 4 L/kg is assumed to be related to decreasing concentrations of Ca and thus to the dissolution of sparingly soluble calcium antimonate. The same leaching mechanism applies with V, but the concentration levels observed are less critical regarding relevant limit values. However, on the long term the behavior of Sb could be problematic for the application of MSWI BA in construction. KW - MSWI bottom ash KW - Leaching KW - Batch tests KW - Lysimeter KW - Antimony PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-508421 DO - https://doi.org/10.1007/s12649-020-01086-2 SN - 1877-2641 VL - 11 IS - 12 SP - 7055 EP - 7065 PB - Springer AN - OPUS4-50842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heisterkamp, I. A1 - Ratte, M. A1 - Schoknecht, Ute A1 - Gartiser, S. A1 - Kalbe, Ute A1 - Ilvonen, O. T1 - Ecotoxicological evaluation of construction products: inter-laboratory test with DSLT and percolation test eluates in an aquatic biotest battery N2 - Background A European inter-laboratory test with 29 participating laboratories investigated whether a battery of four ecotoxicological tests is suitable for assessing the environmental compatibility of construction products. For this purpose, a construction product was investigated with the dynamic surface leaching test (DIN CEN/TS 16637-2) and the percolation test (DIN CEN/TS 16637-3). The eluates were produced centrally by one laboratory and were tested by the participants using the following biotests: algae test (ISO 8692), acute daphnia test (ISO 6341), luminescent bacteria test (DIN EN ISO 11348), and fish egg test (DIN EN ISO 15088). As toxicity measures, EC50 and LID values were calculated. Results Toxic effects of the eluates were detected by all four biotests. The bacteria test was by far the most sensitive, followed by the algae test and the daphnia test; the fish egg test was the least sensitive for eluates of both leaching tests. The toxicity level of the eluates was very high in the bacteria, daphnia, and algae test, with lowest ineffective dilution values of LID = 70 to LID = 13,000 and corresponding EC50 values around or even below 1 volume percent. The reproducibility (approximated by interlaboratory variability) of the biotests was good (< 53%) to very good (< 20%), regardless of the toxicity level of the eluates. The reproducibility of the algae test was up to 80%, and thus still acceptable. Conclusion It can be confirmed that the combination of leaching and ecotoxicity tests is suitable to characterize with sufficient reproducibility the environmental impact posed by the release of hazardous substances from construction products. KW - Inter-laboratory test KW - Construction products KW - Leaching tests KW - Ecotoxicity tests KW - Grouts PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-529198 DO - https://doi.org/10.1186/s12302-021-00514-x VL - 33 IS - 1 SP - Article number: 75 PB - Springer AN - OPUS4-52919 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Per- and polyfluoroalkyl substances (PFAS) in ski waxes and snow from cross-country skiing in Germany - Comparative study of target analysis and sum parameters N2 - Per- and polyfluoroalkyl substances (PFAS) can enter the environment in different ways. Possible sources are PFAS containing consumer products. One common product that makes use of the material properties of PFAS is ski wax. Here, the PFAS ensure less frictional resistance, thus allows for increased speed. However, people who wax their ski with these waxes could absorb PFAS in their body, which can lead to health problems in the long term. Moreover, PFAS applied in ski wax abrade onto snow during use, which contaminates the environment. In our study, we analyzed various currently available ski waxes (2020s) and ski waxes from the 1980s with PFAS target analysis and with the sum parameters extractable organically bound fluorine (EOF), hydrolysable organically bound fluorine (HOF) and total fluorine (TF). Moreover, snow samples from the long-distance cross-country ski trail “Kammloipe” in the Ore mountains in Germany where sampled and analyzed with PFAS target analysis and the adsorbable organically bound fluorine (AOF) sum parameter to document the entry of PFAS from ski waxes into the environment. In opposite to the ski waxes from the 1980s much more ski waxes from the 2020s contain high (total) fluorine values. The highly fluorinated ski waxes contain up to approx. 6% of fluorine. The EOF and HOF sum parameters of the ski waxes are strongly decreased in comparison to the TF values (max. approx. 1000 mg/kg = 0.1%). But even the PFAS-free labeled ski waxes have EOF/HOF values in the low mg/kg range. In the snow samples from different spots of the ski trail, both the AOF sum parameter and the PFAS target analysis identified PFAS. Moreover, on a PFAS hotspot also soil samples were analyzed, which indicate that PFAS from the ski waxes adsorb after snow melting into the soil. Thus, our results show that the use of ski waxes is a possible contribution to the environmental contamination of PFAS, which is hopefully drastically reduced with the ban on fluorinated waxes by the International Ski and Snowboard Federation (FIS). T2 - SETAC Europe CY - Vienna, Austria DA - 11.05.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Contaminated Soil KW - Ski wax PY - 2025 AN - OPUS4-63096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN ED - Simon, Franz-Georg ED - Kalbe, Ute T1 - Measurement of the Environmental Impact of Materials N2 - Throughout their life cycles—from production, usage, through to disposal—materials and products interact with the environment (water, soil, and air). At the same time, they are exposed to environmental influences and, through their emissions, have an impact on the environment, people, and health. Accelerated experimental testing processes can be used to predict the long-term environmental consequences of innovative products before these actually enter the environment. We are living in a material world. Building materials, geosynthetics, wooden toys, soil, nanomaterials, composites, wastes and more are research subjects examined by the authors of this book. The interactions of materials with the environment are manifold. Therefore, it is important to assess the environmental impact of these interactions. Some answers to how this task can be achieved are given in this Special Issue. KW - Leaching KW - Recycling KW - Emissions PY - 2023 UR - https://www.mdpi.com/books/book/6546 SN - 978-3-0365-5983-4 SN - 978-3-0365-5984-1 DO - https://doi.org/10.3390/books978-3-0365-5983-4 SP - 1 EP - 264 PB - MDPI CY - Basel ET - 1 AN - OPUS4-56770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weiler, L. A1 - Pfingsten, J. A1 - Eickhoff, H. A1 - Geist, I. A1 - Hilbig, H. A1 - Hornig, U. A1 - Kalbe, Ute A1 - Krause, K. A1 - Kautetzky, D. A1 - Linnemann, V. A1 - Gschwendtner, M. A1 - Lohmann, D. A1 - Overeem-Bos, E. A1 - Schwerd, R. A1 - Vollpracht, A. T1 - Improving consistency at testing cementitious materials in the Dynamic Surface Leaching Test on the basis of the European technical specification CENTS 16637–2 – Results of a round robin test N2 - The environmental impact assessment of materials is usually based on laboratory tests, mostly in combination with models describing the longterm fate of the substances of interest in the targeted environmental compartment. Thus, laboratory tests are the fundamental link to achieve appropriate assessment conclusions which makes it essential to generate consistent results. This just as applies to the leaching of cementitious materials. In Europe, the leaching behavior of monolithic building materials is tested in the Dynamic Surface Leaching Test following the specification CEN/TS 16637–2. An interlaboratory comparison on European level regarding this technical specification showed relatively high intra- and interlaboratory variations for the tested materials (monolithic copper slag and cement stabilized coal fly ash). Therefore the German Committee for Structural Concrete (DAfStb) framed a guideline to specify additional testing conditions for cementitious materials. To assess the possible improvement by this guidelines measures, a round robin test with 11 participants from Germany and the Netherlands was conducted. This work aims to provide insight into the factors to be considered in the testing of alkaline materials, including sample preparation, and highlights crucial procedures and their manifestation in the results. All evaluated parameters showed improved results compared to the earlier round robin test. The relative standard deviations for repeatability (RSDr) and reproducibility (RSDR) of the elements calcium, barium, antimony, chromium, molybdenum and vanadium, which are the parameters evaluated in both round robin tests, were RSDr = 4%, 4%, 2%, 5%, 5%, and 5% respectively (4% in average) for this work, in comparison to the European round robin test with an average RSDr of 29% (17%, 17%, 20%, 40%, 36%, and 42%). The RSDR improved from 41% (30%, 36%, 29%, 57%, 40%, and 56%) to 14% (12%, 8%, 6%, 28%, 15%, and 12%). CO2 ingress during testing and the inaccuracy of eluate analytics for concentrations close to the determination limits were identified as the main sources of error. KW - Environmental assessment KW - Leaching KW - Heavy metals KW - Round robin test KW - Building Material PY - 2022 DO - https://doi.org/10.1016/j.jenvman.2022.114959 SN - 0301-4797 VL - 314 SP - 1 EP - 9 PB - Elsevier CY - Amsterdam AN - OPUS4-54647 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Diffusive Gradients in Thin-films (DGT) technique as screening tool for per- and polyfluoroalkyl substances (PFAS) contamination in wastewater-based fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of organofluorine surfactants used in the formulations of thousands of consumer goods, including aqueous film-forming foams (AFFF) used to suppress aviation fires in training scenarios, non-stick cookware, fast-food wrappers, water-repellent fabrics, medical equipment, and plastic and leather products. As a result of the perpetual use of PFAS containing products, effluents and sewage sludge from wastewater treatment plants (WWTPs) have been observed to be an important pathway for PFAS into the environment. In Germany, phosphorus and other nutrients from sewage sludge and wastewater should be recycled in WWTPs of cities with a large population. However, it is not clear if PFAS contamination from wastewater and sewage sludge end up in novel wastewater-based fertilizers. Normally, PFAS are analyzed using PFAS protocols typically with time-consuming extraction steps and LC-MS-MS quantification. However, for screening of PFAS contaminations in sewage sludge or wastewater-based fertilizers also passive sampler based on the Diffusive Gradients in Thin-films (DGT) technique can be used for the PFAS extraction. Afterwards, combustion ion chromatography (CIC) can be applied to analyse the “total” amount of PFAS on the passive sampler. Here, we show results from the DGT method in comparison to those of the extractable organic fluorine (EOF) method for a variety of wastewater-based fertilizers. Additionally, we analysed the adsorption of PFAS on the weak anion exchanger (WAX) based DGT passive sampler binding layer by infrared and fluorine K-edge X-ray adsorption near-edge structure (XANES) spectroscopy. T2 - SETAC Europe 2022 CY - Copenhagen, Denmark DA - 15.05.2022 KW - Passive sampling KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge KW - Wastewater PY - 2022 AN - OPUS4-54883 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute A1 - Kalbe, Ute A1 - Happel, O. T1 - Combination of leaching tests with ecotoxicity and chemical analysis – Lessons learnt N2 - The presentation describes analytical methods to characterize eluates from leaching tests and identify organic substances in leachates. Chances to obtain complementary information from ecotoxtests and chemical analysis are discussed. T2 - Workshop: Ecotoxicological evaluation of construction products – test results, implementation in Guidance, Technical Standards and Ecolabelling CY - Online meeting DA - 21.03.2022 KW - Leaching KW - Ecotoxicity KW - Construction products PY - 2022 AN - OPUS4-55276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Heisterkamp, I. A1 - Gartiser, S. A1 - Kretzschmar, M. A1 - Schoknecht, Ute A1 - Kalbe, Ute A1 - Happel, O. A1 - Ratte, M. T1 - Methoden und Kriterien zur Bewertung der Ökotoxizität von Produkten N2 - Die Umweltverträglichkeit von Bauprodukten, die in Kontakt mit Regen- oder Sickerwasser kommen, wurde durch Kombination normierter Elutions- (DSLT, Perkolationstest) und Ökotoxizitätstests (Algen, Daphnien, Fischeier, Leuchtbakterien) sowie Gentoxizitätstests (Ames, umu) untersucht. Ziel des Projektes war es einerseits, einen Beitrag zur Harmonisierung der Prüfmethoden unter CEN/TC 351 zu leisten und andererseits potentielle Produktgruppen, die sich für die Umweltzeichenvergabe des Blauen Engels eignen würden, zu erkennen. Durch umfangreiche qualitative und quantitative chemische Analysen (u. a. GC-MS- sowie LC-MS-Screening) wurden einige der freigesetzten Stoffe identifiziert und anhand von Literaturdaten ökotoxikologisch charakterisiert. Insgesamt wurden 34 Bauprodukte (Dachbahnen, Lacke, Wood-Plastic-Composites, Pflasterfugenmörtel, Korkgranulate, Schaumglasschotter, Wegedecken, Dichtmassen) untersucht. Hierbei wurden insbesondere bei den Fugenmörteln und Korkgranulaten sehr hohe Ökotoxizitäten (bis LID = 16384 bei den Fugenmörteln und LID = 24578 bei den Korkgranulaten) beobachtet. Algen- und Leuchtbakterientests waren in der Regel deutlich empfindlicher als der Daphnien- und Fischeitest. Die untersuchten Dachbahnen, Lacke, Wood-Plastic-Composites und Schaumglasschotter zeigten hingegen keine oder nur sehr geringe Ökotoxizitäten. Zur Qualitätssicherung und Validierung wurde ein Europäischer Ringversuch gemäß den Vorgaben der DIN ISO 5725 organisiert, durchgeführt und ausgewertet. Hierzu wurde ein Fugenmörtel als flächiges Produkt im DSLT und als gebrochenes körniges Produkt im Perkolationstests eluiert und die Eluate nachfolgend in den 29 teilnehmenden Laboren hinsichtlich ihrer Ökotoxizität untersucht. Hierbei wurden insgesamt plausible Ergebnisse und gute (<50 %) bis sehr gute (<20 %) Reproduzierbarkeiten erzielt. Es wird empfohlen, für die Produktgruppen Dachbahnen, Kunstrasen und Sportböden sowie Fugenmörtel Vergabekriterien für den Blauen Engel zu entwickeln KW - Bauprodukte KW - Umweltbewertung KW - Ökotoxizität PY - 2022 UR - https://www.umweltbundesamt.de/publikationen/methoden-kriterien-zur-bewertung-der-oekotoxizitaet SN - 1862-4804 VL - 151/2022 SP - 1 EP - 135 PB - Umweltbundesamt CY - Dessau-Roßlau AN - OPUS4-56679 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Roesch, Philipp T1 - How to investigate potential emission sources of PFAS in consumer product materials? Comparative extraction approaches and sum parameter analysis by combustion ion chromatography (CIC) N2 - Besides classical per- and polyfluorinated alkylated substances (PFAS), side-chain fluorinated polymers (SFPs) are widely applied as efficient anti-wetting and anti-greasing coatings in various daily applicated consumer products such as outdoor apparel, carpetry or paper-based food contact materials. Although the fluorinated sidechains are chemically bound to a base polymer, their release can be triggered by environmental influences or wear-off, thus contribute as significant sources of PFAS in the environment. Since only little knowledge of PFAS and SFP composition in consumer products is available, a comprehensive analytical approach might be beneficial. T2 - SETAC Konferenz 2023 CY - Dublin, Ireland DA - 30.04.2023 KW - PFAS KW - Combustion Ion Chromatography KW - Comsumer good samples PY - 2023 AN - OPUS4-57422 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Vogel, Christian A1 - Simon, Franz-Georg T1 - Antimony in incineration bottom ash – Leaching behavior and conclusions for treatment processes N2 - Antimony (Sb) is used in industrial products mainly as flame retardant in plastic material. Due to such additives in plastics, about a half of Sb ends up in municipal solid waste incineration at the end-of-life and consequently in relevant amounts in the generated bottom ash. In contact with water, the initial leachability is low, as antimonates form sparingly soluble compounds with Ca2+. Following the carbonation of the incineration bottom ash (IBA) during the proceeding ageing the pH in the leachates decreases. With decreasing concentration of Ca in the eluate the solution equilibrium changes and antimonates dissolve. In Germany it is intended to regulate Sb in IBA with the planned implementation of the so called Mantelverordnung (MantelVO, containing provisions on the utilisation of mineral waste) in the near future. The limit values set in the draft might be critical for IBA and therefore pose a risk for the utilisation of the mineral fraction of IBA in the well-established recycling routes. T2 - SUM 2020 – 5th Symposium on Urban Mining and Circular Economy CY - Online meeting DA - 18.11.2020 KW - Bottom ash KW - Leaching KW - Antimony PY - 2020 SP - 1 EP - 4 AN - OPUS4-51622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kalbe, Ute T1 - Wie steht es um die Zukunft der „neuen“ Elutionsverfahren? N2 - Es wird ein historischer Abriss der Entwicklung von Elutionsverfahren insbesondere im Zusammenhang mit der Erarbeitung der Mantelverordnung gegeben. KW - Elutionsverfahren KW - Mantelverordnung KW - Boden KW - Ersatzbaustoffe KW - Abfälle PY - 2020 SN - 0942-3818 VL - 29 IS - 5 SP - 169 EP - 170 PB - Erich Schmidt Verlag GmbH CY - Berlin AN - OPUS4-51447 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Wie naturnah simulieren die Elutionsverfahren? N2 - Die Untersuchung altlastverdächtiger Flächen umfasst viele einzelne Schritte von der Probenahme über die Probenvorbehandlung bis hin zur eigentlichen Analyse, die zur Ergebnisunsicherheit beitragen. Beim Vergleich der Ergebnisse mit Bewertungsmaßstäben, um Entscheidungen zur Bewertung von Altlasten zu treffen, sind diese Faktoren zu berücksichtigen. Die Rolle von verschiedenen Unsicherheitskomponenten wird mit Blick auf Elutionsverfahren diskutiert. T2 - Messen, schätzen und bewerten – Theorie und Praxis der Altlastenbewertung: Online-Altlastenseminar des LLUR CY - Online meeting DA - 27.09.2021 KW - Altlasten KW - Schadstofftransfer KW - Elutionsverfahren KW - BBodSchV KW - Ergebnisunsicherheit PY - 2021 AN - OPUS4-53623 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Roesch, Philipp A1 - Vogel, Christian A1 - Kalbe, Ute A1 - Simon, Franz-Georg T1 - Entwicklung von PFAS-Summenparametern mittels Combustion Ion Chroma- tography (CIC) N2 - Wie können industriell synthetisierte Schadstoffe aus einer Stoffklasse quantifiziert werden, deren genauer Umfang unbekannt ist und auf mehrere tausend Verbindungen geschätzt wird? Im Falle der per- und polyfluorierten alkylierten Substanzen (PFAS) stellen sich Wissenschaftler*innen weltweit seit über zehn Jahren diese Frage. Neben der etablierten Methodik der Einzelstoffanalytik (engl. target analytic) existieren Summenparameteranalysen zur Quantifizierung organisch gebundener fluorierter Verbindungen in Umweltmedien und Konsumprodukten. An der Bundesanstalt für Materialforschung und -prüfung (BAM) beschäftigen wir uns mit der Weiterentwicklung von Summenparametermethoden am Beispiel von PFAS-belasteten Umweltkompartimenten wie Böden, Klärschlämmen und Gewässerproben sowie PFAS-haltigen Konsumgütern. In diesem Beitrag stellen wir zwei ausgewählte Fallbeispiele vor und diskutieren die Vor- und Nachteile der Methoden im Vergleich zur Einzelstoffanalytik. KW - PFAS KW - Combustion Ion Chromatography KW - LC-MS/MS KW - Water analysis KW - Environmental analysis KW - Sum parameter analysis PY - 2023 SN - 1618-3258 VL - 29 IS - 2 SP - 40 EP - 44 AN - OPUS4-57611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Utilization of recycling materials in Germany - Regulations, assessment framework and leaching tools N2 - Der Vortrag wurde im Rahmen des 9th Geoenvironmental Assessment Seminars gehalten der auf Leaching- und Adsorptionstests fokussiert war. Der Vortrag enthielt einen Überblick über die Standardisierung von Leachingverfahren in DIN, CEN und ISO. Die Vorgehensweise der Bewertung des Schadstofftransfers bei der Wiederverwertung von Bodenmaterialien und der Verwertung mineralischer Ersatzbaustoffe in Deutschland wurde hinsichtlich der neuen rechtlichen Rahmenbedingungen dargestellt. Spezielle Herausforderungen bei der Untersuchung von PFAS mit Elutionsverfahren wurden aufgezeigt. T2 - 9th Geoenvironmental Assessment Seminar AIST (National Institute of Advanced Industrial Science and Technology) CY - Tsukuba, Japan DA - 25.03.2024 KW - Recycling of mineral waste KW - Contaminant transfer KW - Leaching KW - Assessment KW - Legislation KW - PFAS PY - 2024 AN - OPUS4-62057 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Susset, Bernd A1 - Kalbe, Ute T1 - Spezifische Herausforderungen bei der PFAS-Elution N2 - Im Teil des Workshops, der sich mit Praxiserfahrungen zu den Elutionsverfahren DIN 19528 und DIN 19529 befasste, wurden spezifische Herausforderungen bei Elutionsuntersuchungen von Bodenproben mit einer PFAS-Kontamination vorgestellt. Aus durchgeführten Robustheitsuntersuchungen im ZAG der Universität Tübingen sowie in der BAM wurden praxisrelevante Schlussfolgerungen erläutert und für einzelne PFAS-Verbindungen und Vorläufersubstanzen konkretisiert. Dabei wurde auch auf die Vergleichbarkeit von Schüttel- und Säulenversuchen beim bewertungsrelevanten Wasser/Feststoff-Verhältnis von 2 l/kg und die Bedeutung des Fest/Flüssigtrennschrittes beim Schüttelverfahren eingegangen. Die Untersuchung von Böden auf PFAS mit Elutionsversuchen ist generell möglich, aber es besteht eine komplexe Abhängigkeit der Konzentrationen im Eluat vom Gesamtgehalt, der Löslichkeit und des Verteilungsmusters der einzelnen PFAS, der Art der Bodenmatrix und dem Einfluss der Probenaufbereitung vor der Analytik. Die geringere Sensitivität der Feststoffanalytik für PFAS im Vergleich zur Eluatanalytik erschwert die Berechnung von Massenbilanzen. T2 - Workshop / Anwendertreffen Elutionsverfahren im Regelungsbereich der Mantelverordnung (ErsatzbaustoffV / BBodSchV) und der EU-BauPVO CY - Berlin, Germany DA - 07.05.2024 KW - Elution KW - PFAS KW - Prekursoren KW - Boden KW - Säulenversuch KW - Schüttelversuch PY - 2024 AN - OPUS4-62065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Ergebnisvergleich Teil 4 – Untersuchung von BM/BG mit und ohne CaCl2-Lösung als Elutionsmittel N2 - Im Teil des Workshops, der sich mit Praxiserfahrungen und Methodenvergleichen zu den Elutionsverfahren DIN 19528 und DIN 19529 befasste, wurden Robustheitsuntersuchungen für die Wahl des Eluenten besonders für Böden mit hohem Humusgehalt und/oder Tongehalt vorgestellt und die Einführung einer neuen Option in die Normen begründet. Der Einsatz 0,001 molarer CaCl2-Lösung als Elutionsmittel führt zu niedrigeren Trübungen im Eluat und reduziert den Aufwand zur Vorbereitung der Eluate für die Folgeanalytik, erleichtert den Fest-Flüssig-Trennschritt bei Schütteleluaten und hat Auswirkungen auf die Mobilisierung/Freisetzungspotenziale bestimmter Analyten, die häufig an Kolloide im Boden binden. T2 - Workshop / Anwendertreffen Elutionsverfahren im Regelungsbereich der Mantelverordnung (ErsatzbaustoffV / BBodSchV) und der EU-BauPVO CY - Berlin, Germany DA - 07.05.2024 KW - Elutionsverfahren KW - Eluent KW - Kolloide PY - 2024 AN - OPUS4-62063 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Robustheit und Validierung der Elutionsnormen N2 - Im Vortrag wurden die den deutschen Elutionsnormen DIN 19528 und DIN 19529 zugrunde liegenden Validierungsdaten erörtert. Dabei wurde auf die Herstellung von Referenzmaterialien durch die BAM, die Vorgehensweise bei den Robustheitsuntersuchungen und die Ableitung der Versuchsbedingungen der Normen erläutert. Die Verfahrenskenndaten aus den durch die BAM veranstalteten Ringversuchen zur Validierung der Elutionsverfahren DIN 19528 und DIN 19527/19529 wurden mit besonderem Focus auf die Vergleichbarkeit von Schüttel- und Säulenversuchen beim bewertungsrelevanten Wasser/Feststoff-Verhältnis von 2 l/kg diskutiert. Des Weiteren wurden Hintergründe für die Überarbeitung der deutschen Elutionsnormen und notwendige Angleichung an die zukünftige harmonisierte europäische Säulenversuchsnorm im Bereich Bauprodukte beleuchtet. T2 - Workshop / Anwendertreffen Elutionsverfahren im Regelungsbereich der Mantelverordnung (ErsatzbaustoffV / BBodSchV) und der EU-BauPVO CY - Berlin, Germany DA - 07.05.2024 KW - Elutionsverfahren KW - Robustheitsuntersuchungen KW - Validierung KW - Ringversuche KW - Verfahrenskenndaten PY - 2024 AN - OPUS4-62061 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Elutionsverfahren im Wandel der Zeit - ISO, CEN, DIN N2 - Ein historischer Abriss der Entwicklung und Standardisierung von Elutionsverfahren auf nationaler, europäischer und internationaler Ebene im Zusammenhang mit deutschen und europäischen Regularien im Bereich der Verwertung von mineralischen Abfällen und der Zertifizierung von Bauprodukten wurde gegeben. Die Bedeutung der Elutionsverfahren für die BBodSchV und EBV (Mantelverordnung), die im Juli 2023 in Kraft getreten sind wurde dabei in den Focus gestellt. T2 - Workshop / Anwendertreffen Elutionsverfahren im Regelungsbereich der Mantelverordnung (ErsatzbaustoffV / BBodSchV) und der EU-BauPVO CY - Berlin, Germany DA - 07.05.2024 KW - Elutionsverfahren KW - Organische und anorganische Schadstoffe KW - Quelltermbestimmung KW - Standardisierung PY - 2024 AN - OPUS4-62058 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Investigating the Thermal Decomposition of PFAS in a Full-Scale Commercial Hazardous Waste Incinerator N2 - Incineration is currently the only commercial full-scale technology available to destroy per- and polyfluoroalkyl substances (PFAS) in large solid and liquid waste streams. Given previous experience of dioxin formation during halogenated waste incineration, concerns about the emission of products of incomplete destruction (PIDs) from PFAS incineration exist. The overarching objective of this project is to track the fate of fluorine during full-scale hazardous waste incineration in order to demonstrate the readiness, viability, and level of safety for thermal PFAS destruction in various waste streams. The specific objectives of this project are (1) to enhance our understanding of key variables and conditions on PFAS incineration performance, (2) to identify major PIDs under insufficient treatment conditions, (3) to explore the catalytic role of fly ash and other process-relevant surfaces in thermal PFAS decomposition, and (4) to determine the potential formation of polyfluorinated dibenzodioxins and dibenzofurans. T2 - CEN/TC 264/WG48 Symposium - Emissions and ambient air - Determination of PFAS CY - Düsseldorf, Germany DA - 16.07.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration PY - 2025 AN - OPUS4-63714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Current status of monitoring of PFAS release from industrial facilities N2 - Increasing studies report per- and polyfluoroalkyl substances (PFAS) in the ambient air and emissions from diverse industrial sources. Therefore, a comprehensive framework for characterizing PFAS emissions by identifying source-specific chemical fingerprints, evaluating emission pathways and assessing the impact of remediation technologies is needed. Depending on the type of PFAS, dedicated sampling and analytical procedures are required. Here, also the detection of possible PFAS transformation products, so-called products of incomplete combustion (PICs) are more mobile or toxic, is also of great interest to evaluate these technologies in terms of mineralisation potential and fluorine mass balance. T2 - Consortium for analysis and remediation of per- and polyfluoroalkyl substances (CAR-PFAS Japan) visit Uni Örebro CY - Online meeting DA - 09.10.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration KW - Remediation PY - 2025 AN - OPUS4-64318 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Per- and Polyfluoroalkyl Substances (PFAS) in Sewage Sludge and Wastewater-based Fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are chemicals which were developed to improve humanity’s quality of life. Due to their high chemical stability and resistance to degradation by heat or acids, PFAS were used in a variety of consumer products. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system resulted in the contamination of effluents and sewage sludge from wastewater treatment plants (WWTPs) (Roesch et al. 2022). Since sewage sludge is often used as fertilizer, its application on agricultural soils has been observed as a significant entry path for PFAS into the environment, specifically in our food chain. In Germany the sewage sludge/biosolid application on agricultural land was banned with the amendment of the German Sewage Sludge Ordinance and by 2029 sewage sludge application will be totally prohibited. However, phosphorus (P) from sewage sludge should still be recycled in WWTPs of cities with a population larger than 50,000 residents. To produce high-quality P-fertilizers for a circular economy, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Due to the strong diversity of industrial PFAS usage it is not clear if a safe application of novel recycled P-fertilizers from WWTPs can be guaranteed. Therefore, we analyzed various sewage sludges and wastewater-based fertilizers. Sewage sludge (SL) samples from various WWTPs in Germany and Switzerland, six sewage sludge ashes (SSA) from Germany, six thermally treated SL and SSA samples with different additives (temperatures: 700-1050 °C), two pyrolyzed SL samples (temperature: 400 °C) and two struvite samples from Germany and Canada were analyzed. The goal was to quantify PFAS in sewage sludges and wastewater-based P-fertilizers with the sum parameter extractable organic fluorine (EOF) by combustion ion chromatography (CIC). The results were compared with data from classical LC-MS/MS target analysis as well as selected samples by HR-MS suspect screening. The EOF values of the SLs mainly range between 154 and 538 µg/kg except for one SL which showed an elevated EOF value of 7209 µg/kg due to high organofluorine contamination. For the SSA samples the EOF values were lower and values between LOQ (approx. 60 µg/kg) and 121 µg/kg could be detected. For the pyrolyzed SLs no EOF values above the LOQ were detected. Moreover, the two wastewater-based struvite fertilizers contain 96 and 112 µg/kg EOF, respectively. In contrast to the EOF values, the sum of PFAS target values were relatively low for all SLs. Additional applied PFAS HR-MS suspect screening aimed to tentatively identify PFAS that could contribute to the hitherto unknown part of the EOF value. The majority of the detected fluorinated compounds are legacy PFAS such as short- and long-chain perfluorocarboxylic acids (PFCA), perfluorosulfonic acids (PFSA), polyfluoroalkyl phosphate esters (PAPs) and perfluorophosphonic acids (PFPA). Moreover, fluorinated pesticides, pharmaceutical as well as aromatic compounds were also identified, which are all included in the EOF parameter. Our research revealed that the current PFAS limit of 100 µg/kg for the sum of PFOS + PFOA in the German Fertilizer Ordinance is no longer up to date. Since the number of known PFAS already exceeds 10,000, the ordinance limit should be updated accordingly. Recent regulations and restrictions on using long-chain PFAS (≥C8) have resulted in a significant shift in the industry towards (ultra-)short-chain alternatives, and other, partly unknown, emerging PFAS. Ultimately, also fluorinated pesticides and pharmaceuticals, which end up as ultrashort PFAS in the WWTPs, have to be considered as possible pollutants in fertilizers from wastewater, too. T2 - Dioxin Konferenz CY - Maastricht, Netherlands DA - 10.09.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge KW - Fertilizer PY - 2023 AN - OPUS4-58345 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Combining DGT and combustion ion chromatography (CIC) as screening tool for per- and polyfluoroalkyl substances (PFAS) contamination in wastewater-based fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of organofluorine surfactants used in the formulations of thousands of consumer goods. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system have been resulted in contaminated effluents and sewage sludge from wastewater treatment plants (WWTPs) which became an important pathway for PFAS into the environment. Because sewage sludge is often used as fertilizer its application on agricultural soils has been observed as significant input path for PFAS into our food chain. To produce high-quality phosphorus fertilizers for a circular economy from sewage sludge, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Normally, PFAS are analyzed using PFAS protocols typically with time-consuming extraction steps and LC-MS/MS target quantification. However, for screening of PFAS contaminations in wastewater-based fertilizers also the DGT technique can be used for the PFAS extraction. Afterwards, combustion ion chromatography (CIC) can be applied to analyze the “total” amount of PFAS on the DGT binding layer. The DGT method was less sensitive and only comparable to the extractable organic fluorine (EOF) method values of the fertilizers in samples with >150 µg/kg, because of different diffusion properties for various PFAS, but also kinetic exchange limitations. However, the DGT approach has the advantage that almost no sample preparation is necessary. Moreover, the PFAS adsorption on the DGT binding layer was investigated via surface sensitive spectroscopical methods, such as Fourier-transform infrared (FT-IR) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - DGT Konferenz CY - Paris, France DA - 11.10.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge PY - 2023 AN - OPUS4-58575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - INPR A1 - Vogel, Christian A1 - Helfenstein, J. A1 - Massey, M. A1 - Kretzschmar, R. A1 - Schade, U. A1 - Verel, R. A1 - Chadwick, O. A1 - Frossard, E. T1 - Spectroscopic analysis shows crandallite can be a major component of soil phosphorus N2 - Phosphorus (P) bioavailability is crucial for the productivity of natural and agricultural ecosystems, and soil P speciation plays a major role therein. Better understanding of P forms present in soil is thus essential to predict bioavailability. Most studies on soil P forms differentiate between Ca-bound P (e.g. apatite), organic P, Fe-bound P, and Al-bound P. In our analysis of a Ca, Al, and P rich soil from the Kohala region of Hawaii, we identified the mineral crandallite, CaAl3(PO4)2(OH)5∙H2O, a mineral previously not considered to play a significant role in soils. Crandallite was first identified with powder X-ray diffraction, and then confirmed with microfocused P K-edge X-ray absorption near edge structure (XANES) spectroscopy, micro-infrared spectroscopy, and solid-state 31P nuclear magnetic resonance (NMR) spectroscopy. Crandallite XANES spectra were distinct from other common XANES spectra due to the presence of features in the post-edge region of the spectrum. Linear combination fitting of bulk P K-edge XANES spectra allowed the determination of the proportion of crandallite to the total P content, indicating that crandallite comprises up to half, possibly even more of the soil P in the samples. Crandallite is therefore an important and potentially overlooked component of soil P, which pedogenically forms in soils with high P, Al, and Ca contents, where it likely plays an important role in P bioavailability. KW - Phosphor KW - XANES spectrosocpy KW - infrared spectroscopy PY - 2025 DO - https://doi.org/10.2139/ssrn.5556609 SP - 1 EP - 31 PB - SRN AN - OPUS4-64739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wittwer, Philipp A1 - Roesch, Philipp A1 - Vogel, Christian A1 - Simon, Fabian A1 - Gehrenkemper, Lennart A1 - Feldmann, Ines A1 - Simon, Franz-Georg T1 - Less Is More: Influence of Cross-Linking Agent Concentration on PFOS Adsorption in Chitosan N2 - As a result of the continuous use of persistent per- and polyfluoroalkyl substances (PFAS), e.g., in aviation firefighting foams, contamination with PFAS has been found in soil, groundwater, and surface water around thousands of industrial and military installations. Due to their harmful (environmental) potential, further dispersion in the environment needs to be stopped, which can be achieved by appropriate absorption materials. In this work, the influence of the cross-linking agent epichlorohydrin (ECH) concentration on the perfluorooctanesulfonic acid (PFOS) adsorption capacity of chitosan gel was investigated. It was found that higher ECH concentration during the cross-linking step decreases the PFOS adsorption capacity of the cross-linked chitosan gel from 0% to 4% ECH solution by about 15%. Using a concentration of 1%, ECH resulted still in an acid-stable material, and a maximum PFOS loading capacity of 4.04 mmol/g was obtained, one of the highest described in the literature. Furthermore, we used a rapid small-scale column test to compare the PFOS adsorption capacity of chitosan and activated carbon, each in both milled and unmilled form. Unmilled chitosan showed the highest PFOS adsorption capacity considering adsorption material dry masses (>0.9 and <0.4 mmol/g for both types of chitosan and activated carbon, respectively). Milled activated carbon proved to be the better adsorption material, considering the fixed volume of the adsorber (>99.9% PFOS adsorbed). Overall, the cross-linking agent concentration in chitosan is a crucial factor influencing its PFOS absorption potential. Our results feature cross-linked chitosan as an effective economic and ecologic alternative for PFOS adsorption in aqueous solutions. KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Remediation PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-618406 DO - https://doi.org/10.3390/app142311145 VL - 14 IS - 23 SP - 1 EP - 13 PB - MDPI AN - OPUS4-61840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogel, Christian A1 - Urban, Klaus A1 - Ackerhans, C. A1 - Gorbushina, Anna T1 - Analysis of Carbon and Nitrogen from Atmospheric Sources by Bulk Deposition Sampling at various locations in Germany N2 - Atmospheric deposition of particulate matter is an important indicator of air pollution and a significant factor in material surface fouling. The elemental composition of this nutrient-containing dust depends largely on the exposure region and time as well as on climate. Therefore, in this paper we report an analysis of atmospheric pollutions with a self-made low-cost bulk deposition sampler directed at sampling deposition via air transport and rainfall. We used the device in diverse environments - thus comparing an urban region, an area surrounded by forest and an area mainly dominated by agriculture. The total organic carbon (TOC) and total nitrogen (TN) amounts were selected as indicator parameters and analyzed in a biweekly rhythm for three and a half and two years, respectively. The TOC value responded to particulate matter in the urban area, especially significant were the influences of the New Year's firework in urban and pollen in the rural forest area. In contrast, the TN value was more under the influence of the nitrogen emissions in the agriculture-dominated area. However, the TN value did not correlate with the NOx values in the urban area because the atmospheric nitrogen emissions in the city might originate from various emission sources. Summarizing, the TOC and TN values of the self-made low-cost bulk deposition sampler were in good agreement with environmental events of their immediate surrounding. Moreover, the selected containers and sampling procedures are universally applicable to monitor and analyze organic as well as inorganic parameters (e.g. metal ions) of atmospheric deposition. KW - Passive sampling KW - Biomonitoring KW - Air Analysis PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-609373 DO - https://doi.org/10.1016/j.envadv.2024.100583 SN - 2666-7657 VL - 17 SP - 1 EP - 9 PB - Elsevier Ltd. AN - OPUS4-60937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Roland A1 - Scholz, Philipp A1 - Jung, Christian A1 - Weidner, Steffen T1 - Thermo-Desorption Gas Chromatography-Mass Spectrometry for investigating the thermal degradation of polyurethanes N2 - Thermo-Desorption Gas Chromatography-Mass Spectrometry (TD-GC-MS) was used to investigate the thermal degradation of two different polyurethanes (PU). PU samples were heated at different heating rates and the desorbed products were collected in a cold injection system and thereafter submitted to GC-MS. Prospects and limitations of the detection and quantification of semi-volatile degradation products were investigated. A temperature dependent PU depolymerization was found at temperatures above 200 °C proved by an increasing release of 1,4-butanediol and methylene diphenyl diisocyanate (MDI) representing the main building blocks of both polymers. Their release was monitored quantitatively based on external calibration with authentic compounds. Size Exclusion Chromatography (SEC) of the residues obtained after thermodesorption confirmed the initial competitive degradation mechanism indicating an equilibrium of crosslinking and depolymerization as previously suggested. Matrix-Assisted Laser Desorption Ionization (MALDI) mass spectrometry of SEC fractions of thermally degraded PUs provided additional hints on degradation mechanism. KW - Thermo-desorption KW - Mass spectrometry KW - Polyurethanes KW - Thermal degradation PY - 2023 DO - https://doi.org/10.1039/D3AY00173C SN - 1759-9660 SP - 1 EP - 6 PB - Royal Society for Chemistry AN - OPUS4-57307 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Elutionsverfahren in Forschung und regulatorischem Kontext N2 - Elutionsverfahren sind ein Tool für Umweltverträglichkeitsprüfungen verschiedenster Materialien im Kontakt mit Wasser. Im früheren Fachbereich 4.3 Schadstofftransfer und Umwelttechnologien wurden dazu umfangreiche Kompetenzen vor allem im Zusammenhang mit mineralischen Reststoffen sowie vielfältigen Bauprodukten aufgebaut und experimentelle Erfahrungen gesammelt. Darüber hinaus wurde auch der Austrag von Partikeln betrachtet und die gleichzeitige Bewertung von Mikroplastik- und Schadstoffausträgen aus Kunsstofftrasen untersucht. Es sind aber auch weitere Anwendungen beispielsweise zur Prüfung der Beständigkeit von Materialien denkbar. Im Workshop wurden Anwendungsbereiche von Elutionsverfahren diskutiert mit dem Ziel der besseren Vernetzung, der gemeinsamen Nutzung von Ressourcen und Identifikation von Synergien zwischen den Fachbereichen bzw. Aktivitätsfeldern. T2 - Workshop - Bewertung der Freisetzung von (Schad)stoffen aus Materialien mit Elutionsverfahren CY - Berlin, Germany DA - 21.01.2025 KW - Elution KW - Materialien KW - Schadstoffe PY - 2025 AN - OPUS4-65023 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Duarte-Ruiz, D. A1 - Saßnick, H.-D. A1 - Ferreira De Araujo, F. A1 - Gentzmann, Marie A1 - Huthwelker, T. A1 - Cocchi, C T1 - X-ray absorption spectroscopy of scandium oxide polymorphs N2 - Scandium oxide (Sc2O3) is a rare-earth oxide with significant potential in key technological areas, but due to its limited supply a deep understanding of its characteristics in different crystalline phases is still missing. Here, we present a combined experimental and ab initio X-ray absorption spectroscopy investigation of Sc2O3 focusing on excitations from the O K-edge and the Sc L2,3-edge. While measurements are performed on a cubic sample, the most stable phase under ambient conditions, six different polymorphs are computed, including two high-pressure phases with a trigonal and monoclinic lattice in addition to the cubic phase, as well as three computationally predicted structures. Our analysis of the structural and electronic properties reveals significant similarities between the cubic polymorph and the high-pressure trigonal phase, while the monoclinic crystal exhibits distinct features. The spectra simulated for these similar phases from the solution of the Bethe–Salpeter equation show very good agreement with measurements. Additional comparison with results computed in the independent-particle approximation highlights the dominant role of electron–hole correlations in shaping the absorption features, particularly at the O K-edge, where a common pattern with the features of other sesquioxides is identified. Our findings offer new insight into the spectral fingerprints of Sc2O3 polymorphs, aiding in situ characterization and informing sustainable materials management. KW - Scandium PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-650806 DO - https://doi.org/10.1039/d5ra06446e VL - 15 IS - 56 SP - 47814 EP - 47825 AN - OPUS4-65080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Loose, Florian T1 - End-of-Life Carbon Fiber Reinforced Polymers in Steelmaking - Accessing a C-Rich Residue Stream as Alternative Reducing Agent N2 - As one of the most energy and carbon consuming industries, steelmakers have an intrinsic interest in the development of technologies, reducing their carbon footprint as well as their carbon input. Besides generating new feedstocks from biomass or waste polymers, the valorization of carbon fiber reinforced polymer (CFRP) waste streams seems to be extremely promising based on the high carbon content of carbon fibers (CF), chars from CFRP and even unprocessed CFRP waste of >92%, 98% and 79%, respectively. Although, reduction of environmental impact from those high-performance materials was achieved by the development of smart recycling solutions, the continuous truncation by mechanical treatment of CF over multiple cycles, analogous to paper fibers, and the large global CFRP waste stream of 62 kt/a demand for a sustainable management of end-of-life (EOL) CFRP. Recently it was demonstrated that CF can be used safely as reductant in pyrometallurgical processes in a downhole electric furnace without significant WHO fiber emission. Therefore we anticipate a huge potential of CF based materials as sustainable reductant for steelmaking in an electric arc furnace (EAF). To facilitate the applicability of EOL CFRP in steelmaking, we investigated the interaction between CF based materials and liquid metal phases, appearing during the process, on different scales. Particularly, we examined the reactivity, wettability and dissolution behavior of CF and CFRP concerning liquid slag and steel. The presented results indicate that understanding the impact of the microstructure of CF on their behavior is crucial for their application in EAF steelmaking without risking potential hazards by WHO fiber emission. Besides the detailed elucidation of structure reactivity relationships of CF, the broader impact on circular economy will be presented. T2 - ESTEP Workshop Resi4Future: Residue valorization in iron and steel industry - sustainable solutions for a cleaner and more competitive future Europe CY - Online meeting DA - 20.11.2020 KW - Carbon Fibers KW - Steelmaking KW - Electric Arc Furnace KW - Secondary Recources KW - Sustainability PY - 2020 AN - OPUS4-51613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bandow, N. A1 - Aitken, M. D. A1 - Geburtig, Anja A1 - Kalbe, Ute A1 - Piechotta, Christian A1 - Schoknecht, Ute A1 - Simon, Franz-Georg A1 - Stephan, Ina T1 - Using Environmental Simulations to Test the Release of Hazardous Substances from Polymer-Based Products: Are Realism and Pragmatism Mutually Exclusive Objectives? N2 - The potential release of hazardous substances from polymer-based products is currently in the focus of environmental policy. Environmental simulations are applied to expose such products to selected aging conditions and to investigate release processes. Commonly applied aging exposure types such as solar and UV radiation in combination with water contact, corrosive gases, and soil contact as well as expected general effects on polymers and additional ingredients of polymer-based products are described. The release of substances is based on mass-transfer processes to the material surfaces. Experimental approaches to investigate transport processes that are caused by water contact are presented. For tailoring the tests, relevant aging exposure types and release quantification methods must be combined appropriately. Several studies on the release of hazardous substances such as metals, polyaromatic hydrocarbons, flame retardants, antioxidants, and carbon nanotubes from polymers are summarized exemplarily. Differences between natural and artificial exposure tests are discussed and demonstrated for the release of flame retardants from several polymers and for biocides from paints. Requirements and limitations to apply results from short-term artificial environmental exposure tests to predict long-term environmental behavior of polymers are presented. KW - Environmental simulations KW - Polymer-based products KW - Artificial weathering KW - Degradation KW - Leaching KW - Soil contact PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509310 DO - https://doi.org/10.3390/ma13122709 SN - 1996-1944 VL - 13 IS - 12 SP - Paper 2709, 22 PB - MDPI CY - Basel, Switzerland AN - OPUS4-50931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Stephan, Dietmar A1 - Meng, Birgit A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Hirsch, Tamino A1 - Manninger, Tanja T1 - Effect of gypsum on the hydration of fused cement clinker from basic oxygen furnace slag N2 - Fused cement clinker can be produced from molten basic oxygen furnace slag (BOFS) by way of a reductive thermochemical treatment. During the thermochemical treatment, oxidic iron is reduced to metallic iron and separated. The resulting low-iron slag has a chemical and mineralogical composition similar to ordinary Portland cement (OPC) clinker. In this study, the hydraulic reactivity of the fused clinker from BOFS with and without gypsum was investigated using isothermal calorimetry, differential scanning calorimetry, in situ X-ray diffraction and powder X-ray diffraction. Furthermore, a synthetic fused clinker without foreign ions and fused clinker produced by a mixture of both materials was studied. The hydraulic reaction of the fused clinker from BOFS was considerably slower than that of OPC. However, the reaction can be accelerated by adding gypsum as a sulfate carrier. Furthermore, the results showed an increased reaction rate with decreasing content of foreign ions such as Fe, P or Mn. KW - General Materials Science KW - Building and Construction PY - 2024 DO - https://doi.org/10.1680/jadcr.23.00070 SN - 0951-7197 SP - 1 EP - 19 PB - Telford AN - OPUS4-59391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, Said T1 - Aktuelle Diskussionen aus dem Fachbeirat der BAM N2 - Im Folgenden soll über aktuelle Diskussionen und Arbeitsschwerpunkte im Fachbeirat der BAM und von der Zulassungsstelle berichtet werden. Es werden Änderungen im Zusammenhang mit der Zulassungsrichtlinie für Kunststoffdichtungsbahnen vorgestellt. Es wird über die aktuelle Diskussion über die Anforderungen z. B. an metallische Sensoren für Dichtungskontrollsysteme berichtet. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden aufgezeigt. T2 - 20. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 12.03.2024 KW - Dichtungskontrollsystem KW - Deponie KW - Kunststoffdichtungsbahn PY - 2024 SN - 978-3-943443-54-7 VL - 20 SP - 16 EP - 23 CY - Leipzig AN - OPUS4-59893 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - R-Rhenania - Modifiziertes Rhenania Phosphat aus Klärschlammasche für Bayern N2 - Im Verbundprojekt R-Rhenania wird eine industrielle Demonstrationsanlage am Standort der Monoverbrennungsanlage Altenstadt der Firma Emter errichtet und im Jahr 2024 den Betrieb aufnehmen. Die vorhandene Rostfeuerung-Monoverbrennung wird so umgebaut, dass ein neues thermochemisches Verfahren integriert werden kann, welches hochwirksame und schadstoffarme Dünger produziert (bis zu 17.000 t/a). Die thermochemischen Produkte werden in Gefäß- und Feldversuchen im ökologischen Landbau auf ihre Düngewirkung getestet. Die Umweltverträglichkeit der Demonstrationsanlage wird untersucht, wie auch die Übertragbarkeit des Verfahrens auf weitere Regionen. T2 - Statusseminar RePhoR CY - Frankfurt am Main, Germany DA - 03.05.2023 KW - Phosphor KW - Monoverbrennung KW - Recycling KW - Nährstoffe KW - Dünger PY - 2023 AN - OPUS4-59486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes T1 - Klärschlammasche Monitoring 2022/23 - Erste Ergebnisse: P Löslichkeiten & Schwermetalle N2 - Im Rahmen des BMBF Projektes R-Rhenania wurden von fast allen Monoverbrennungsanlagen in Deutschland Klärschlammasche-Probeneingesammelt. Diese Aschen wurden auf die Gesamtchemie-Zusammensetzung, Schwermetalle und die Löslichkeit des Phosphates untersucht. T2 - 95. Sitzung des DWA Fachausschusses KEK 3 CY - Hannover, Germany DA - 27.11.2023 KW - Phosphor KW - Monoverbrennungsanlage KW - Neutralammoniumcitrat KW - Zitronensäure PY - 2023 AN - OPUS4-59437 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piehl, Patrick T1 - Thermochemical Treatment of Steel Work Dusts and Sludges for the Recovery of Zinc and Iron N2 - Steel work dusts and sludges usually contain severe amounts of zinc, lead, cadmium, and other heavy metals, which hinder direct recycling and make these materials potentially hazardous for the environment. To tackle this issue, here, two thermochemical treatment methods for the reductive workup of blast furnace sludge, electric arc furnace dust, and comparable steelwork dusts are presented. In the first method, carbon contained blast furnace sludge is employed as reducing agent for the material’s metal oxides. By this, heavy metals get evaporated and a metallic iron containing residue that may be reused in electric arc furnace steelmaking is formed. Additionally, the use of hydrogen for reducing iron and heavy metal oxides in steelwork dusts is presented. Here, high evaporation rates of heavy metals can be reached, and sponge iron is formed. Investigations using thermogravimetry and equilibrium simulations provide insides into the reactions taking place. For both processes an upscaling to pilot scale is ongoing. T2 - EUROSLAG 2024 CY - Bilbao, Spain DA - 23.10.2024 KW - Electric arc furnace dust KW - Blast furnace sludge KW - Recycling KW - Ressource recovery KW - Zinc PY - 2024 AN - OPUS4-61499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Smol, M. A1 - Adam, Christian A1 - Preisner, M. T1 - Circular economy model framework in the European water and wastewater sector N2 - One of the key elements in the transformation towards a circular economy (CE) is providing more sustainable practices for resources and waste management. Improvement actions focused on transformation towards a CE should be targeted at all groups of materials and waste. As water is essential for human survival and well-being and plays a significant role in sustainable development (SD), the actions related to the reuse of water and the recovery of raw materials from wastewater and other water-based waste should be taken. The paper presents a proposition for a new CE model framework in the water and wastewater sector, which includes the six following actions: reduction—prevent wastewater generation in the first place by the reduction of water usage and pollution reduction at source; reclamation (removal)—an application of effective Technologies for the removal of pollutants from water and wastewater; reuse—reuse of wastewater as an alternative source of water supply (non-potable usage), recycling—recovery of water from wastewater for potable usage; recovery—recovery of resources such as nutrients and energy from water-based waste, and rethink—rethinking how to use resources to create a sustainable economy, which is `free` of waste and emissions. The novelty of the proposed CE model framework is that it presents possible ways of implementing CE principles in the water and wastewater sector, with a strong emphasis not only technological but also organisational and societal changes. Application of the proposed model may help to further transform the European economy to the CE model. Moreover, the indicated model can be significant tool supporting an assessment of local or regional progress towards CE in the water and wastewater sector and further environmental management and planning. KW - Circular economy KW - Phosphorus recovery KW - Waste water PY - 2020 DO - https://doi.org/10.1007/s10163-019-00960-z SP - 1 EP - 16 PB - Springer AN - OPUS4-50441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Smol, M. A1 - Adam, Christian A1 - Kugler, Stefan T1 - Inventory of Polish municipal sewage sludge ash (SSA) – Mass flows, chemical composition, and phosphorus recovery potential N2 - This paper presents an inventory of sewage sludge ashes (SSA) generated in the mono-incineration plants for municipal sewage sludge in Poland. This research focused on the detailed study of mass flows, chemical composition, and phosphorus recovery potential. There are currently 11 sludge mono-incineration plants operated with a total capacity of 160,300 Mg dry weight (d.w.) of sludge annually. Recently, a significant increase in the amount of SSA generated in these plants has been observed, reaching 26,756 Mg in 2018. Chemical composition of SSA showed significant amounts of the main nutrients: calcium (~14%), phosphorus (~13%), magnesium (~3%), and potassium (~1%). Additional main elements were iron (~14.5%), silicon (~13%), and aluminium (~6%). The main trace elements in the SSA were zinc (~3750 mg/kg) and copper (~899 mg/kg). Pollutants, according to fertilizer regulations of different countries, present in Polish SSA were chromium(~703 mg/kg), nickel (~260 mg/kg), lead (~94 mg/kg), and Cadmium (~9 mg/kg). The radionuclides, uranium, and thorium often present in higher amounts in commercial phosphate rock-based fertilizers, were only detected in SSA t low levels of 4–9 mg/kg and 2–3 mg/kg, respectively. Theoretical phosphorus recovery potential from the SSA (from plants in Cracow, Lodz, Gdansk, Gdynia, Szczecin, and Kielce) was estimated at 1613.8 Mg, of which 33.9% is bioavailable. Currently, in Poland, the recommended approach is the production of fertilizers as a result of the extraction of phosphorus from the SSA with its use in the production of secondary mineral fertilizers. Further research in this area is required considering Polish conditions and legislation. KW - Municipal sewage sludge KW - Sewage sludge ash (SSA) KW - Phosphorus KW - Recovery potential PY - 2020 DO - https://doi.org/10.1016/j.wasman.2020.07.042 VL - 116 SP - 31 EP - 39 PB - Elsevier Ltd AN - OPUS4-51093 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Phosphorrückgewinnung - Ergebnisse des Projekts extraWERT N2 - Es wurden erste Ergebnisse des Projekts extraWERT vorgestellt. Im Projekt werden monatlich Klärschlammproben von 10 kommunalen Kläranlagen untersucht, deren P-Gehalt im Grenzbereich der AbfKlärV liegt zwischen 1,7 und 2,3%. Die ersten Ergebnisse lagen zu fünf Kläranlagen vor, es wurden Daten zum TS-Gehalt, zur oTS und zu den Nährstoffgehalten präsentiert. T2 - DWA-Netzwerktag des Nord-Ost CY - Berlin, Germany DA - 22.01.2020 KW - Klärschlamm KW - AbfKlärV KW - Phosphorrückgewinnung KW - Nährstoffe PY - 2020 AN - OPUS4-50300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Legislation and technology development for P-recovery in Germany N2 - New developments in legislation and technology development for P-recovery were presented with focus on the situation in Germany. T2 - SMART-Plant joint Stakeholder Workshop CY - Berlin, Germany DA - 29.01.2020 KW - P-recovery KW - Sewage sludge ordinance PY - 2020 AN - OPUS4-51764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery in Germany – recent developments N2 - The recent developments of phosphorus recovery in Germany were presented. The funding program RePhoR was introduced with focus on the demonstration project R-Rhenania that is coordinated by BAM. T2 - Green Deal 2020 conference CY - Online-Meeting DA - 14.12.2020 KW - Phopshorus recovery KW - Waste water treatment KW - Recycling fertiliser PY - 2020 AN - OPUS4-51837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - Modifiziertes Rhenania Phosphat auf Klärschlammasche für Bayern N2 - Es wurde das Projekt R-Rhenania MODIFIZIERTES RHENANIA PHOSPHAT AUS KLÄRSCHLAMMASCHE FÜR BAYERN mit seinen Inhalten und der Projektstruktur vorgestellt. T2 - 6. P-Rück-Kongress: Phosphor - ein kritischer Rohstoff mit Zukunft CY - Online meeting DA - 25.11.2020 KW - Phosphorrückgewinnung KW - Klärschlammasche PY - 2020 AN - OPUS4-51667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - The role of junction strength in the performance of geogrids N2 - Designing the performance of geogrids in reinforce soil constructions usually does not consider long-term behavior and possible failure modes of junctions between longitudinal and transverse ribs. How could behavior of junctions be included? To which extend is it necessary? On the conference Geo-Chicago 2016, Swan and Yuan presented an ultimate limit state equation for the short-term material resistance of junctions. We discuss limitations and suggest improvements to include long-term behavior of junctions. Nevertheless, the approach applies only to a specific mode of shear-tensile failure of junctions and only to strictly rigid geogrids. A new design concept presented in the same year by Jacobs on the conference GeoAmerica for the special case of the anchorage of geogrids, which reinforce capping system on long and steep slopes of landfills, tried to overcome these drawbacks. We discuss the aspects of this concept related to the long-term behavior of junctions and the interplay between the load applied to junctions and the flexibility of longitudinal ribs. This interplay and the long-term junction strength determine the long-term behavior of geogrids. T2 - GeoAmericas 2020 CY - Online meeting DA - 26.10.2020 KW - Geogitter KW - Geokunststoffe KW - Deponie PY - 2020 AN - OPUS4-51485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussion aus dem Fachbeirat der BAM N2 - Das Jahr 2020 war vor allen Dingen von der Pandemie geprägt, die alle Bereiche des Lebens und Arbeitens beeinflusst hat und immer noch beeinflusst. Dies hat sich auch auf verschiedene Maßnahmen im Zusammenhang mit zugelassenen Produkten ausgewirkt. In diesem Zusammenhang sollen die Punkte kurz aufgeführt werden. Des Weiteren soll aufgezeigt werden, wie bei der Bearbeitung der Richtlinien, der Zulassungstätigkeit und Beurteilung der Produkte an der BAM und im Fachbeirat vorgegangen wird. Darüber hinaus soll noch einmal kurz auf die Entlassung aus der Nachsorgephase eingegangen werden. Am Ende sollen verschiedene aktuelle Fragestellungen des Fachbeirat aufgezeigt werden. T2 - 17. Leipziger Deponiefachtagung CY - Online meeting DA - 02.03.2021 KW - Deponie KW - Geokunststoffe KW - Kunststoffdichtungsbahn PY - 2021 AN - OPUS4-52213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes T1 - Success-Story CaNaPO4: Erfolgreiche REACH Registrierung und Inbetriebnahme großtechnischer Anlagen N2 - Aufgrund der Vorgaben in der novellierten Klärschlammverordnung 2017 (AbfKlärV) wird für die meisten Kläranlagen ab 2029 verpflichtend das enthaltene Phosphat zurückzugewinnen bzw. einer Phosphatrückgewinnung zuzuführen. Aktuell gehen dafür einige thermochemische als auch nasschemische Verfahren in Betrieb. Die meisten thermochemischen Verfahren arbeiten mit einer vergleichbaren Grundidee. Es werden Alkali-Additive wie Na2CO3 vor der thermischen Behandlung eingemischt. Die anschließend produzierten thermochemischen Rezyklate enthalten als Phosphatphasen Calciumalkaliphosphate wie CaNaPO4, welche zu hoher Phosphatlöslichkeit und Pflanzenverfügbarkeit in den Rezyklaten führen. Aktuell werden solche thermochemischen Verfahren an den Standorten Altenstadt (Oberbayern), Michelstadt (Odenwald) und Breisach-Grezhausen (nähe Freiburg) in Betrieb genommen. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2025 KW - Phosphor KW - Recycling KW - Großtechnik KW - Dünger PY - 2025 AN - OPUS4-64710 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes T1 - Phosphorrückgewinnung in Deutschland: Thermochemisches Verfahren in Altenstadt N2 - Die Firma Emter GmbH betreibt die Klärschlammverbrennungsanlage Altenstadt und hat in die bestehende Monoverbrennung einen thermochemischen Prozess integriert, um hochwirksame und schadstoffarme Düngemittel aus Klärschlamm herzustellen. Die Anlage ist aktuell die größte Phosphor-recyclinganlage in Deutschland mit der die Vorgaben der AbfKlärV bereits frühzeitig umgesetzt werden. Im Prozess wird schwerlösliches Phosphat in pflanzen-verfügbares Phosphat umgewandelt und gleichzeitig werden Schadstoffe thermisch zerstört oder entfernt. Seit Mitte 2024 steht eine Kapazität für die jährliche Produktion von 15.000 Tonnen des sogenannten R-Rhenania- Phosphats bereit. Dieser Recyclingdünger wird nach REACH registriert, erfüllt alle Vorgaben der Düngemittelverordnung und kann in der Landwirtschaft breit eingesetzt werden. Die Eigenschaften des Phosphats, wie etwa dessen Unlöslichkeit in Wasser, entsprechen den Anforderungen des ökologischen Landbaus. Aufgrund dieser Passfähigkeit finden im Rahmen von R-Rhenania seit 2001 bis heute umfangreiche Feldversuche im ökologischen Landbau statt. Das Projekt R-Rhenania begleitet die Phosphorrecyclinganlage mit Untersuchungen zur Produktqualität, mit Gefäßversuchen und Feldversuchen im ökologischen Landbau, mit Ökobilanzierung und der Konfektionierung verschiedener Düngemittelprodukte. T2 - Eröffnungsfeier Altenstadt CY - Altenstadt, Germany DA - 16.10.2026 KW - Phosphor KW - Recycling KW - Großtechnik KW - Dünger KW - Thermochemisch PY - 2025 AN - OPUS4-64824 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Adam, Christian T1 - P-Rückgewinnung aus Klärschlammasche - AshDec® Verfahren N2 - Klärschlammaschen können eine hohe Phosphatkonzentration aufweisen und stellen damit einen geeigneten Sekundärrohstoff für die Produktion von Phosphatdüngemitteln dar. Bisher wird dieses Potential der Klärschlammaschen für die Phosphor-Rückgewinnung jedoch kaum genutzt, da die in den Aschen enthaltenen Phosphate für Pflanzen kaum verfügbar und die Aschen teilweise mit toxischen Schwermetallen belastet sind. Im AshDec®-Verfahren wird die Klärschlammaschen im Drehrohrofen im Temperaturbereich 800-1000°C unter Zugabe von Alkali-Additiven (bsp. Na2CO3) thermochemisch behandelt, um ein wirksames und schadstoffarmes Phosphatdüngemittel herzustellen. Aktuell bereitet die Firma Emter GmbH den Bau der ersten großtechnischen AshDec®-Anlage mit einer Kapazität von 30.000 Jahrestonnen Klärschlammasche am Standort ihrer Klärschlammverbrennungsanlage (Altenstadt / Oberbayern) vor. Die erste Ausbaustufe dieser Anlage wird durch das BMBF-Projekt R-Rhenania im Rahmen der Förderinitiative RePhoR begleitet. T2 - 2. Thüringer Klärschlammkommunalkonferenz CY - Thüringer Ministerium für Umwelt, Energie und Naturschutz DA - 21.06.2022 KW - Rückgewinnung KW - Phosphor KW - Klärschlamm KW - Dünger PY - 2022 AN - OPUS4-55088 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus dem Fachbeirat der BAM N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. Besondere Aufmerksamkeit gilt der Diskussion um die Einbauhilfe im Schutzschichtsystem, der Einführung einer europäischen Zugversuchsnorm für Kunststoffdichtungsbahnen sowie der Fremdüberwachung der Produktion geosynthetischer Komponenten. Darüber hinaus werden neue Anforderungen an Edelstahlelektroden in Dichtungskontrollsystemen und die Spannungsrissbeständigkeit von PE-HD-Dichtungsbahnen thematisiert. T2 - 35. Karlsruher Deponie- und Altlastenseminar CY - Karlsruhe, Germany DA - 15.10.2025 KW - Deponie PY - 2025 AN - OPUS4-64410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schneider, Joachim A1 - Schraut, Katharina T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 SN - 978-3-944310-72-5 VL - 10 SP - 222 EP - 233 PB - TK-Verlag CY - Neuruppin AN - OPUS4-57684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holm, O. A1 - Leube, Peter A1 - Vogel, Christian A1 - Kennedy, E. A1 - Stockenhuber, M. A1 - Lucas, J. A1 - Truong, T. A1 - Rappé, A. A1 - Lu, W. A1 - Blotevogel, J. T1 - Thermische Zerstörung von PFAS in der Sondermüllverbrennung: Einfluss von Temperatur und PFAS-Konzentration N2 - Aufgrund ihrer einzigartigen molekularen Beschaffenheit werden per- und polyfluorierte Alkylsubstanzen (PFAS) in vielen unterschiedlichen Produkten und Anwendungsgebieten eingesetzt. Da sie generell eine hohe Persistenz aufweisen und je nach individueller Struktur unterschiedlich mobil sind, sind sie mittlerweile in allen Umweltkompartimenten und ubiquitär nachzuweisen. Ihre potenzielle (ökologische) Toxizität birgt dabei erhebliche Umweltrisiken, weshalb PFAS in den letzten Jahren mehr und mehr in den Fokus von Umweltverbänden und -behörden gelangten. Gleichzeitig beschäftigen sich Forschungseinrichtungen mit der möglichst weitreichenden Entfernung aus der Umwelt sowie mit deren (anschließender) Zerstörung. Im Projekt ER24-4073 „Untersuchung des thermischen Abbaus von PFAS in einer kommerziellen Großanlage zur Verbrennung gefährlicher Abfälle“, welches vom U.S. Department of Defense (DoD ) über das Strategic Environmental Research and Development Program (SERDP) gefördert wird, untersuchen deutsche, australische und amerikanische Partner die Behandlung von PFAS-haltigen Abfallströmen in einer großtechnischen Verbrennungsanlage, um die Einsatzbereitschaft, Machbarkeit und Sicherheit dieser Zerstörungsmethode zu demonstrieren. T2 - Berliner Konferenz Abfallwirtschaft und Energie CY - Berlin, Germany DA - 28.01.2026 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Verbrennung KW - Kontaminierter Boden PY - 2026 SN - 978-3-911006-65-1 SP - 66 EP - 77 PB - TK Verlag AN - OPUS4-65513 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 9. Nachtrag zum Zulassungsschein 12/BAM IV.3/09/00 für eine Schutzschicht bestehend aus einer sandgefüllten Schutzbahn für Kunststoffdichtungsbahnen in Deponieabdichtungen N2 - 9. Nachtrag zum Zulassungsschein 12/BAM IV.3/09/00 für eine Schutzschicht bestehend aus einer sandgefüllten Schutzbahn für Kunststoffdichtungsbahnen in Deponieabdichtungen der Firma G quadrat GmbH, Krefeld. KW - Deponie KW - Schutzschicht KW - Abdichtungssystem PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654339 SP - 1 EP - 31 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-65433 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Identifikation und Einordnung von historischen Lehmbauteilen für die Wiederverwendung hinsichtlich Anreicherung von Schadstoffen und bauschädlichen Salzen N2 - Lehmbaustoffe, einschließlich Lehm aus dem historischen Baubestand, bieten ein hohes Potenzial für ihre Wiederverwendbarkeit und die Schonung natürlicher Ressourcen. Zur Bewertung des Wiederverwendungspotenzials gibt es nur wenige Studien hinsichtlich der Schadstoffbelastung und der Anreicherung von Salzen in Gebäuden aus dem historischen Bestand. Tonminerale, die in Lehmbaustoffen als Bindemittel fungieren, können Schadstoffe binden. Die Region Mitteldeutschland ist geprägt durch jahrzehntelange Einwirkung erheblicher Schadstoffemissionen aus der Chemie- und Braunkohleindustrie. Der Eintrag von Schadstoffen in Lehmbaustoffe ist außerdem aus geogenen Hintergrundbelastungen denkbar, z. B. in Auenböden beeinflusst durch Einträge aus dem Erzbergbau. Salzbildende Anionen wie Chloride oder Nitrate können aufgrund ihrer hohen Löslichkeit mittels kapillarer Kräfte durch die Porenstruktur transportiert werden. In Lehmwänden können sie vor allem in oberflächennahen Lagen, in denen höhere Verdunstungsraten vorherrschen, durch Bindung mit in Lösung vorliegenden oder baustoffeigenen Kationen auskristallisieren und bauschädliche Salze ausbilden. Auch durch spezifische Nutzungen akkumulierte Schadstoffe, z. B. durch die Einwirkung von Tabakrauch, könnten theoretisch einer Wiederverwendung von Lehm entgegenstehen. In Anbetracht der Herausforderungen hinsichtlich der klimatischen und gesellschaftlichen Veränderungen, sind wissenschaftliche Erkenntnisse im Lehmbau erforderlich, die eine Integration in eine nachhaltige Kreislaufwirtschaft ermöglichen. Bei bisherigen Gesetzgebungsverfahren zu rezyklierten Baustoffen wurden Lehmbaustoffe noch nicht berücksichtigt. Ziel einer Vorstudie im Rahmen der WIR!-Initiative GOLEHM ist die Überprüfung der Wiederverwendbarkeit Wiederverwendbarkeit von Lehmbaustoffen aus historischen Bauten an Stichproben hinsichtlich der Umwelt- und Nutzerverträglichkeit. Für den Raum Mitteldeutschland können damit Anhaltspunkte darüber gegeben werden, welche Schadstoffe und bauschädlichen Salze in welchem Maße in Lehmbaustoffen aus dem Gebäudebestand erwartet werden können. Daraus können Hinweise zum Umgang mit Lehmbaustoffen aus historischen Gebäuden abgeleitet werden. Darüber hinaus wurden exemplarisch an zwei Gebäuden mikrobiologische Untersuchungen zur Ermittlung einer möglichen Belastung mit Schimmelpilzen vorgenommen. T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Schadstoffe KW - Wiederverwendung KW - Historischer Baubestand PY - 2024 AN - OPUS4-61881 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogel, Christian A1 - Sekine, R. A1 - Huang, J. A1 - Steckenmesser, D. A1 - Steffens, D. A1 - Huthwelker, T. A1 - Borca, C. A1 - Pradas del Real, A. A1 - Castillo-Michel, H. A1 - Adam, Christian T1 - Effects of a nitrification inhibitor on nitrogen species in the soil and the yield and phosphorus uptake of maize N2 - Phosphorus (P) resource availability is declining and the efficiency of applied nutrients in agricultural soils is becoming increasingly important. This is especially true for P fertilizers from recycled materials, which often have low plant availability. Specific co-fertilization with ammoniumcan enhance P plant availability in soils amended with these P fertilizers, and thus the yield of plants. To investigate this effect, we performed a pot experiment with maize in slightly acidic soil (pH 6.9) with one water-soluble (triple superphosphate [TSP]) and two water-insoluble (sewage sludge-based and hyperphosphate [Hyp]) P fertilizers and anammoniumsulfate nitrate with or without a nitrification inhibitor (NI). The dry matter yield of maize was significantly increased by the NI with the Hyp (from 14.7 to 21.5 g/pot) and TSP (from 40.0 to 45.4 g/pot) treatments. Furthermore, P uptake was slightly increased in all three P treatments with the NI, but not significantly. Olsen-P extraction and P K-edge micro-X-ray absorption near-edge structure (XANES) spectroscopy showed that apatite-P of the water insoluble P fertilizers mobilized during the plant growth period. In addition, novel nitrogen (N) K-edge micro-XANES spectroscopy and the Mogilevkina method showed that the application of an NI increased the fixation of ammonium in detectable hot spots in the soil. Thus, the delay in the nitrification process by the NI and the possible slow-release of temporarily fixed ammoniumin the soil resulted in a high amount of plant available Ammonium in the soil solution. This development probably decreases the rhizosphere pH due to release of H+ by plants during ammoniumuptake, whichmobilizes phosphorus in the amended soil and increases the dry matter yield of maize. This is especially important for water-insoluble apatite-based P fertilizers (conventional and recycled), which tend to have poor plant availability. KW - Fertilzer KW - Phosphorus recovery KW - Ammonium KW - Nitrification inhibitor KW - XANES spectroscopy KW - Diffusive gradients in thin films (DGT) PY - 2020 DO - https://doi.org/10.1016/j.scitotenv.2020.136895 SN - 1879-1026 VL - 715 SP - 1 EP - 8 PB - Elsevier CY - Amsterdam AN - OPUS4-50477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes T1 - Thermochemisches P Recycling aus Klärschlamm - Erste großtechnische Anlage am Standort Altenstadt (Bayern) N2 - Im Verbundprojekt R-Rhenania wird eine industrielle Demonstrationsanlage am Standort der Monoverbrennungsanlage Altenstadt der Firma Emter errichtet und im Jahr 2024 den Betrieb aufnehmen. Die vorhandene Rostfeuerung-Monoverbrennung wird so umgebaut, dass ein neues thermochemisches Verfahren integriert werden kann, welches hochwirksame und schadstoffarme Dünger produziert (bis zu 17.000 t/a). Die thermochemischen Produkte werden in Gefäß- und Feldversuchen im ökologischen Landbau auf ihre Düngewirkung getestet. Die Umweltverträglichkeit der Demonstrationsanlage wird untersucht, wie auch die Übertragbarkeit des Verfahrens auf weitere Regionen. T2 - 13. VDI Klärschlammbehandlung CY - Koblenz, Germany DA - 14.09.2022 KW - Phosphor KW - Versuchskampagne KW - Recycling KW - Nährstoffe KW - Dünger PY - 2022 AN - OPUS4-59576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussionen aus dem Fachbeirat der BAM N2 - Im Folgenden soll über aktuelle Diskussionen und Arbeitsschwerpunkte im Fachbeirat der BAM und von der Zulassungsstelle berichtet werden. Es werden Änderungen im Zusammenhang mit der Zulassungsrichtlinie für Kunststoffdichtungsbahnen vorgestellt. Es wird über die aktuelle Diskussion über die Anforderungen z. B. an metallische Sensoren für Dichtungskontrollsysteme berichtet. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden aufgezeigt. T2 - 20. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 12.03.2024 KW - Deponie KW - Kunststoffdichtungsbahn KW - Dichtungskontrollsystem PY - 2024 AN - OPUS4-59894 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steckenmesser, D. A1 - Vogel, Christian A1 - Herzel, Hannes A1 - Félix, R. A1 - Adam, Christian A1 - Steffens, D. T1 - Thermal treatment of sewage sludge for phosphorus fertilizer production: a model experiment N2 - Phosphorus (P) resource availability and quality is declining and recycling P-fertilizers from waste materials are becoming increasingly important. One important secondary P resource is sewage sludge (SSL) where P is often bound as aluminum phosphate (Al-P), iron phosphate (Fe-P) and polyphosphate (poly-P), respectively. Thermal treatment in different ways is a promising way in P recycling to produce highly plant-available P-fertilizers. To investigate mechanisms behind transformation of hardly available P-species toward plant-available P forms we treated a model SSL containing different kinds of defined P sources by low-temperature conversion (LTC) at 500 °C and subsequent thermochemical treatment of the LTC product with Na additives (TCT) at 950 °C, respectively. Pot experiments with ryegrass were carried out to determine the plant availability of P of the different treatments. The poly-P (here pyrophosphates) based fertilizers had a very high plant availability after both thermal treatments. During LTC treatment the plant availability of the Fe-P and Al-P variants increased because of the Formation of Fe(II) phosphates and/or pyro-/polyphosphates. Especially the formation of Al-polyphosphate shows a high plant availability. The subsequent TCT further increased strongly the plant availability of the Fe-P variants because of the formation of highly plant-available CaNaPO4. Thus, a direct TCT without prior LTC probably also produce CaNaPO4 and is recommended for Fe-P based SSL. However, a molar Ca/P ratio of � 1 in the fertilizer is favorable for CaNaPO4 formation. Thus, the knowledge on the source of primary P in SSL is essential for choosing the accurate thermal treatment method to produce highly plant-available P-fertilizers from SSL. KW - Phosphorus KW - Sewage sludge KW - X-ray diffraction KW - X-ray absorption near-edge structure (XANES) spectroscopy KW - Fertilizer PY - 2021 DO - https://doi.org/10.1080/01904167.2021.1994595 SN - 0190-4167 VL - 45 IS - 8 SP - 1123 EP - 1133 PB - Taylor & Francis Online AN - OPUS4-53755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Klimaschonende Bindemittel auf der Basis von Rohstoffen der Circular Economy N2 - Die Zementindustrie und weitere energieintensive Industrien wie etwa die Stahlindustrie stehen vor dem Hintergrund der Transformation unserer Gesellschaft zur Klimaneutralität vor erheblichen Herausforderungen. Ziel dieser Branchen ist perspektivisch die vollständige Vermeidung klimaschädlicher Emissionen – mit besonderem Fokus auf Kohlendioxid. Neben der Umstellung auf regenerative Energieträger, sind im Speziellen für die Zementindustrie die erheblichen Anteile an CO2-Emissionen durch die Entsäuerung von Kalkstein zukünftig zu vermeiden. Da die hervorragenden Bindemitteleigenschaften des bisher hauptsächlich in Zementen eingesetzten Portlandklinkers jedoch auf Calciumverbindungen wie Tri- und Di-calciumsilikaten basieren, stellt die Substitution des Kalks derzeit für die Zementindustrie die größte Herausforderung dar. Neben vollständig neuen Bindemittelsystemen ohne Verwendung von Kalk und CCS/CCU-Technologien zur Vermeidung der CO2-Emissionen bei Verwendung von Kalk, können Abfälle und Nebenprodukte wie etwa Betonbrechsand, verschiedene Schlacken und weitere Massenreststoffe sinnvoll zur Einsparung von Rohstoffen und zur Vermeidung von CO2-Emissionen eingesetzt werden. Es gilt diese Potentiale von Sekundärrohstoffen branchenübergreifend zu identifizieren und Synergien zwischen den Branchen nutzbar zu machen. Hierbei werden neben der chemischen Zusammensetzung der Abfälle und Nebenprodukte auch die Verfügbarkeit und der Massenstrom relevante Kriterien sein. Die potenziellen Sekundärrohstoffe und deren Gemische mit chemisch ähnlicher Zusammensetzung wie die bisher verwendeten Bindemittel, können durch verschiedene technische Ansätze wieder in reaktive Bindemittel umgewandelt und damit nutzbar gemacht werden. Eine gezielte Umwandlung der nicht reaktiven mineralischen Phasen in neue mineralische Phasen mit guten Bindemitteleigenschaften, kann u. a. durch Schmelzprozesse erzielt werden. In Schmelzen können bei hohen Temperaturen die bestehenden, nicht reaktiven mineralischen Phasen zerstört und neue mineralische Phasen mit guten Bindemitteleigenschaften erzeugt werden. Hohe Freiheitsgrade durch gezielte Einstellung der stofflichen Zusammensetzung der Schmelze, durch Stoffseparationen und durch geregelte Abkühlregimes können eine maßgeschneiderte Erzeugung neuer Bindemitteltypen ermöglichen. Aufgrund der hohen erforderlichen Temperaturen von Schmelzprozessen ist die Umsetzung dieser neuen Verfahren nach Möglichkeit in bestehenden pyrometallurgischen Produktionsrouten wie etwa der Stahlproduktion vorzunehmen. So kann etwa der Einsatz von Betonbrechsand als Schlackebildner in der Stahlproduktion zielführend sein, wenn die Schlacke wieder zu einem Bindemittel prozessiert wird und in Zementen Verwendung findet. Eine stoffliche Kreislaufführung wäre hiermit gegeben, wobei der Einsatz von Kalkstein als Schlackebildner oder Rohstoff für die Zementproduktion, und damit die entsprechenden CO2-Emissionen, vermieden werden. Die Entwicklung neuartiger Bindemittelsysteme auf Basis von Sekundärrohstoffen sollte von erforderlichen Anpassungen und neuen Entwicklungen in der Regelsetzung und Normung begleitet werden. Vor allem muss gewährleistet sein, dass die mit neuen Bindemitteln hergestellten Betone den hohen Anforderungen an Dauerhaftigkeit und Umweltverträglichkeit genügen. Des Weiteren sollte mit den etablierten Methoden, wie etwa der Lebenszyklusanalyse, untersucht werden, inwiefern und in welchem Umfang die neuen technischen Entwicklungen zu Nachhaltigkeit und Klimaschutz beitragen. T2 - GERRI - BGR Rohstoffkonferenz 2022 CY - Hannover, Germany DA - 05.07.2022 KW - Zement KW - Schlacke KW - Rotschlamm KW - Klimaneutralität PY - 2022 AN - OPUS4-55193 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Schadstoffe/Störstoffe versus Recycling - Diskussion ausgewählter Beispiele N2 - Im Vortrag wurde anhand dreier Beispiele diskutiert, wie sich die Festlegung von Grenzwerten auf das Recycling von Sekundärrohstoffen auswirken kann. Die Diskussion mit Fachleuten soll die Ausgestaltung der Urban Mining Strategie des BMUV unterstützen. T2 - KartAL V Fachgespräch zur Entwicklung einer nationalen Urban Mining Strategie "Schadstoffe versus Recycling" CY - Dresden, Germany DA - 30.10.2024 KW - Urban Mining KW - Schadstoffgrenzwerte PY - 2024 AN - OPUS4-61512 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - extraWERT Forschungsvorhaben N2 - Die novellierte AbfKlärV (2017) beinhaltet die Verpflichtung zum P-Recycling ab einem P-Gehalt im Klärschlamm von 20 g/kg. Im Vortrag werden Ergebnisse des Forschungsvorhabens extraWERT zu diesem Themenkomplex vorgestellt. Es werden Untersuchungen zu P-Gehalten deutscher Klärschlämme und zu den zulässigen Analysemethoden dafür vorgestellt. T2 - Tagung: "Vom Abwasser zum Nährstoff": CY - Karslruhe, Germany DA - 28.09.2022 KW - Phosphorrückgewinnung KW - Klärschlamm PY - 2022 AN - OPUS4-55847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Per- und polyfluorierte Alkylsubstanzen (PFAS) während der Klärschlammverbrennung – Analytische Methoden zur Überwachung N2 - Per- and polyfluoroalkyl substances (PFAS) are a group of more than 12,000 anionic cationic, zwitterionic and neutral anthropologic substances which have been used extensively in a variety of products and industries due to their lipo- and hydrophobic properties, and inert physical and chemical stability. As a result of continuous use of fluorinated consumer products, effluents and sewage sludge from wastewater treatment plants (WWTPs) have been shown to be an important source of PFAS contamination in the environment. While environmental exposure of organic pollutants like PFAS, pesticides and pharmaceuticals have to be avoided, phosphorus from sewage sludge must be used in Germany among other things to produce high-quality P-fertilizers for a circular economy. However, the fate of legacy and emerging PFAS compounds during sewage sludge incineration or pyrolysis is for the most parts still unknown. In particular, PFAS analysis in exhaust air from industrial facilities has not yet been standardized in Germany, which means that no comparable results are available for possible regulation. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2024 KW - Klärschlamm KW - Per- and Polyfluoroalkyl substances (PFAS) PY - 2024 AN - OPUS4-61628 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vogel, Christian A1 - Hoffmann, Marie A1 - Taube, Mareike A1 - Krüger, O. A1 - Baran, R. A1 - Adam, Christian T1 - Uranium and thorium species in phosphate rock and sewage sludge ash based phosphorus fertilizers N2 - Phosphorus (P) is an essential element for all forms of life and is thus often applied as phosphate rock-based P-fertilizers in agriculture to enable continuous farming. However, these P-fertilizers contain also hazardous uranium (U) and thorium (Th), up to 660 and 220 mg/kg, respectively. On the contrary, novel P-fertilizers made from sewage sludge (ash) contain only low mass fractions of U and Th. In addition to the total amount of U and Th in P-fertilizers, their mobility and bioavailability is important, which depends to a large extent on their chemical state, especially oxidation state and chemical bonding. Thus, we analyzed their chemical state in various P-fertilizers by U and Th L3-edge HERFD-XANES spectroscopy. Phosphate rocks and sewage sludge-based P-fertilizers contain mainly U(IV) compounds which have only a low bioavailability. In contrast, acidic treatment of phosphate rock to produce super phosphates lead to an oxidation to U(VI) compounds (including formation of uranium phosphates) with a strongly increased bioavailability. On the contrary, all analyzed P-fertilizers contain Th in form of strongly insoluble phosphates and oxides with a low bioavailability. Additionally performed water extractions and Diffusive Gradients in Thin-films (DGT) experiments support these findings. KW - Phosphorus fertilizer KW - Sewage sludge KW - X-ray absorption near-edge structure (XANES) spectroscopy KW - Diffusive Gradients in Thin-films (DGT) KW - Extraction PY - 2020 DO - https://doi.org/10.1016/j.jhazmat.2019.121100 SN - 0304-3894 VL - 382 SP - 121100, 1 EP - 6 AN - OPUS4-48872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes T1 - Modifiziertes Rhenania Phosphat aus der Klärschlammverbrennung mit thermochemischem Aufschluss N2 - Der Betreiber der Klärschlammverbrennungsanlage Altenstadt (Emter GmbH) integriert einen thermochemischen Prozessschritt in die vorhandene Monoverbrennung und erweitert die Anlage entsprechend, um einen Ausgangsstoff für die Düngemittelproduktion zu erzeugen und damit zur Phosphatrückgewinnung gemäß Klärschlammverordnung (AbfKlärV) beizutragen. Die Umrüstung der Anlage fand im ersten Halbjahr 2024 statt und seit Sommer 2024 steht eine Kapazität für die jährliche Produktion von 15.000 Tonnen schadstoffarmen R-Rhenania Phosphat mit hochwirksamen Phosphatverbindungen zur Verfügung. Diese Demonstrationsanlage wird durch ein wissenschaftliches Monitoring im vom BMFTR geförderte Projekt R-Rhenania (2020-2026) mit u.a. Ökobilanzierungen, Gefäß- und Feldversuche begleitet. Der Projektpartner sePura plant den produzierten Dünger vollständig regional in Bayern zu verwerten. T2 - P-RÜCK – 11. Phosphor Kongress CY - Stuttgart, Germany DA - 19.11.2025 KW - Phosphor KW - Recycling KW - Thermochemisch KW - Großtechnik KW - Klärschlamm PY - 2025 AN - OPUS4-65018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schröder, Simon Alexander A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Stephan, Ina A1 - Hohmann, Gloria A1 - Ziegert, Christof T1 - Identifikation und Einordnung von historischen Lehmbauteilen für die Wiederverwendung hinsichtlich Anreicherung von Schadstoffen und bauschädlichen Salzen T1 - Identification and classification of historical earth construction elements for recycling in respect of accumulation of pollutants and structurally damaging salts N2 - Lehmbaustoffe, einschließlich Lehm aus dem historischen Baubestand, bieten ein hohes Potenzial für ihre Wiederverwendbarkeit und die Schonung natürlicher Ressourcen. Zur Bewertung des Wiederverwendungspotenzials gibt es nur wenige Studien hinsichtlich der Schadstoffbelastung und der Anreicherung von Salzen in Gebäuden aus dem historischen Bestand. Tonminerale, die in Lehmbaustoffen als Bindemittel fungieren, können Schadstoffe binden. Die Region Mitteldeutschland ist geprägt durch jahrzehntelange Einwirkung erheblicher Schadstoffemissionen aus der Chemie- und Braunkohleindustrie. Der Eintrag von Schadstoffen in Lehmbaustoffe ist außerdem aus geogenen Hintergrundbelastungen denkbar, z. B. in Auenböden beeinflusst durch Einträge aus dem Erzbergbau. Salzbildende Anionen wie Chloride oder Nitrate können aufgrund ihrer hohen Löslichkeit mittels kapillarer Kräfte durch die Porenstruktur transportiert werden. In Lehmwänden können sie vor allem in oberflächennahen Lagen, in denen höhere Verdunstungsraten vorherrschen, durch Bindung mit in Lösung vorliegenden oder baustoffeigenen Kationen auskristallisieren und bauschädliche Salze ausbilden. Auch durch spezifische Nutzungen akkumulierte Schadstoffe, z. B. durch die Einwirkung von Tabakrauch, könnten theoretisch einer Wiederverwendung von Lehm entgegenstehen. In Anbetracht der Herausforderungen hinsichtlich der klimatischen und gesellschaftlichen Veränderungen, sind wissenschaftliche Erkenntnisse im Lehmbau erforderlich, die eine Integration in eine nachhaltige Kreislaufwirtschaft ermöglichen. Bei bisherigen Gesetzgebungsverfahren zu rezyklierten Baustoffen wurden Lehmbaustoffe noch nicht berücksichtigt. Ziel einer Vorstudie im Rahmen der WIR!-Initiative GOLEHM ist die Überprüfung der Wiederverwendbarkeit Wiederverwendbarkeit von Lehmbaustoffen aus historischen Bauten an Stichproben hinsichtlich der Umwelt- und Nutzerverträglichkeit. Für den Raum Mitteldeutschland können damit Anhaltspunkte darüber gegeben werden, welche Schadstoffe und bauschädlichen Salze in welchem Maße in Lehmbaustoffen aus dem Gebäudebestand erwartet werden können. Daraus können Hinweise zum Umgang mit Lehmbaustoffen aus historischen Gebäuden abgeleitet werden. Darüber hinaus wurden exemplarisch an zwei Gebäuden mikrobiologische Untersuchungen zur Ermittlung einer möglichen Belastung mit Schimmelpilzen vorgenommen. N2 - Earth construction materials, including earth from historical building stock, offer high potential in terms of their recyclability and sparing use of natural resources. Yet, only a few studies have been conducted on the levels of pollutants and the accumulation of salts in buildings from the historical building stock to enable an assessment of the potential for recycling. The aim of a preliminary study as part of the GOLEHM Initiative from WIR! is to use spot checks to review the recyclability of earth construction materials from historical buildings in terms of environmental impact and tolerance by users. This could provide indicators for the Central Germany region on which pollutants and structurally damaging salts can be expected in earth construction materials from the building stock and to what extent, allowing conclusions to be drawn on how to manage earth construction materials from historical buildings. Additionally, microbiological inspections of two sample buildings were performed to assess a potential contamination with mould. T2 - Lehm 2024 Fachtagung CY - Weimar, Germany DA - 27.09.2024 KW - Lehm KW - Wiederverwendung KW - Kreislaufwirtschaft KW - Schadstoffe KW - Bauschädliche Salze PY - 2024 SP - 1 EP - 8 CY - Weimar AN - OPUS4-61883 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herzel, Hannes A1 - Dombinov, V. A1 - Vogel, Christian A1 - Willbold, S. A1 - Levandowski, G. V. A1 - Meiller, M. A1 - Müller, F. A1 - Zang, J. W. A1 - da Fonseca-Zang, W. A. A1 - Jablonowski, N. D. A1 - Schrey, S. D. A1 - Adam, Christian T1 - Soybean Fertilized by P-Phases from Bagasse-Based Materials: P-Extraction Procedures, Diffusive Gradients in Thin Films (DGT), and X-ray Diffraction Analysis (XRD) N2 - The Brazilian sugarcane industry produced around 173 million tons (Mt) of bagasse in 2018. Bagasse is a by-product of juice extraction for ethanol and sugar production and is combusted in order to generate power, producing up to 10 Mt of ash per year. This ash contains various concentrations of plant nutrients, which allow the ash to be used as a crop fertilizer. However, the concentration and extractability of phosphorus (P), an essential plant nutrient, are low in bagasse ash. To increase the P content, we co-gasified and co-combusted bagasse with P-rich chicken manure. The resulting ash was thermochemically post-treated with alkali additives (Na2SO4 and K2SO4) to increase the availability of P to plants. We aimed to: (i) investigate the effect of thermochemical post-treatment of co-gasification residue and co-combustion ash on P availability to soybeans, (ii) explore the potential of chemical extraction methods (citric acid, neutral ammonium citrate, formic acid, and Mehlich-I) and diffusive gradients in thin films (DGT) to predict the availability of P to soybeans, and (iii) identify the responsible P-phases using X-ray diffraction . We evaluated P availability to soybeans growing in Brazilian Oxisol soil in two independent greenhouse pot experiments. The positive effect of thermochemical treatment on P availability from gasification residue was confirmed through the observation of increased P uptake and biomass in soybean plants. These findings were confirmed by chemical extraction methods and DGT. The gasification residue contained whitlockite as its main P-bearing phase. Thermochemical post-treatment converted whitlockite into highly soluble CaNaPO4. In contrast, co-combustion ash already contained highly soluble Ca(Na,K)PO4 as its main P-bearing phase, making thermochemical post-treatment unnecessary for increasing P availability. In conclusion, increased extractability and availability of P for soybeans were closely connected to the formation of calcium alkali phosphate. Our findings indicate that this combined methodology allows for the prediction of P-fertilization effects of ash. KW - Sugar cane bagasse KW - Chicken manure ash KW - Thermochemical treatment KW - Nutrient KW - Plant availability PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509735 DO - https://doi.org/10.3390/agronomy10060895 VL - 10 SP - 895 EP - 6 PB - MDPI AN - OPUS4-50973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Egloffstein, T. ED - Burkhardt, G. T1 - Aktuelles aus der Arbeit des BAM-Fachbeirats N2 - Der Fachbeirat kommt bereits seit 13 Jahren in seiner jetzigen Form zusammen, um Zulassungsrichtlinien, weitere Dokumente und fachliche Fragestellungen zu beraten. Die Zeit bringt auch personelle Veränderungen mit sich, darüber wollen wir berichten. Derzeit wird die Zulassungsrichtlinie für Schutzschichten im Fachbeirat und in seiner Arbeitsgruppe Geotextilien und Kunststoff Dränelemente (AG Geotextilien) überarbeitet. Zudem wurde die Zulassungsrichtlinie für Kunststoffdichtungsbahnen auf den aktuellen Stand der Regelsetzung und Normung gebracht. Bestimmte Medien, die hier bei einigen Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Hier werden die Hintergründe und Zusammenhänge in Kürze aufgezeigt. Zuletzt wird die Diskussion in Bezug auf den Einsatz von Rezyklaten in den zugelassenen Produkten aufgeführt. T2 - Karlsruher Deponie- und Altlastenseminar 2022 CY - Karlsruhe, Germany DA - 19.10.2022 KW - Deponie KW - Abdichtungssystem KW - Schutzschichten PY - 2022 SN - 978-3-939662-31-0 VL - 42 SP - 23 EP - 32 PB - ICP Eigenverlag Bauen und Umwelt CY - Karlsruhe AN - OPUS4-56209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Die Spannungsrissbeständigkeit von Kunststoffdichtungsbahnen aus PE-HD und die Zulassungsrichtlinie für Schutzschichten N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen der Zulassungsrichtlinie für Schutzschichten im und durch den Fachbeirat vorgestellt werden. T2 - 19. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 14.03.2023 KW - Spannungsrissbeständigkeit KW - Deponie KW - Kunststoffdichtungsbahn PY - 2023 SN - 978-3-943443-53-0 VL - 19 SP - 25 EP - 32 PB - PRESSEL Digitaler Produktionsdruck AN - OPUS4-57194 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Leers, K. A1 - Herzel, Hannes A1 - Emter, J. A1 - Brey, C. A1 - Leimkötter, D. A1 - Künstler, J. A1 - Arnold, U. A1 - Burkhardt, J. A1 - Adam, Christian T1 - Untersuchungen zur agronomischen Wirksamkeit des R-Rhenania Phosphats aus der ersten großtechnischen Anlage N2 - Aufgrund ihrer Phosphorgehalte bieten Klärschlammaschen (KSA) Potentiale für die Herstellung von Phosphatdüngern. Da die agronomische Wirksamkeit von KSA häufig gering ist, bedarf es einer Aufbereitung. Diese kann sowohl vor oder während der Verbrennung des Klärschlamms als auch nachgeschaltet durch eine Aufbereitung der KSA erfolgen. Mit dem nachgeschalteten, thermochemischen AshDec® Verfahren können unter Hinzugabe eines Natrium-Additivs bereits wirksame aschebasierte Düngerprodukte aus KSA hergestellt werden. Im Rahmen des BMBF-Projekts „R-Rhenania“ wurde auf dieser Basis ein thermochemisches Verfahren für eine Rostfeuerung entwickelt, bei dem die Zugabe des Natrium-Additivs direkt bei der Klärschlammverbrennung erfolgt. So sollen die hochwirksamen aschebasierten Dünger direkt bei der Klärschlammverbrennung entstehen (R-Rhenania-Prozess). Der Vergleich von Produkten aus beiden Prozessen (R-Rhenania und nachgeschaltetes AshDec Verfahren) zeigt, dass die chemische Zusammensetzung vergleichbar ist. In Versuchskampagnen in der Monoverbrennungsanlage der Firma Emter GmbH in Altenstadt (Oberbayern) konnte gezeigt werden, dass die Phosphatlöslichkeit in neutraler Ammoniumcitratlösung (PNAC-Löslichkeit) der R-Rhenania Produkte von der Dosierung des Natrium-Additivs abhängt. Am Standort Altenstadt korreliert eine Konzentration von über 8 Gew.-% Na im Produkt mit einer relativen PNAC-Löslichkeit von mindestens 80 % und eine vollständige Löslichkeit mit einem Na-Gehalt von 10,5 Gew.-% Na. Beim Einsatz von R-Rhenania Produkten als P-Dünger für Sommerweizen konnte eine hohe agronomische Wirksamkeit nachgewiesen werden. In den Gefäßversuchen zeigte sich zudem ein Zusammenhang zwischen der PNAC-Löslichkeit und der Düngerwirksamkeit, wobei diese Wirksamkeit der Produkte mit zunehmender Löslichkeit anstieg. Während die Wirksamkeit unbehandelter KSA vergleichbar war zu einer ungedüngten Kontrollvariante, erwiesen sich R-Rhenania Produkte mit einer PNAC-Löslichkeit von mehr als 80 % als besonders effektiv. Die Düngewirkung bei diesen Produkten war sowohl vergleichbar zu einem AshDec-Produkt als auch zu einem konventionellen, wasserlöslichen P-Düngemittel. Auf Grund der erfolgreichen Prozessentwicklung und der nachgewiesenen agronomischen Wirksamkeit der Produkte, wurde am Standort Altenstadt das thermochemische R-Rhenania-Verfahren in die vorhandene Klärschlammmonoverbrennungsanlage integriert. Ab dem Sommer 2024 können dort 15.000 t/a R-Rhenania Dünger hergestellt werden. T2 - Berliner Klärschlamm Konferenz CY - Berlin, Germany DA - 11.11.2024 KW - Phosphor KW - Recycling KW - Dünger KW - Monoverbrennung KW - Klärschlamm PY - 2024 SN - 978-3-911006-83-5 SP - 316 EP - 328 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin AN - OPUS4-61907 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Joachim T1 - Usage of BOF slag and next generation EAF slag in the cement industry N2 - Increasing amounts of new types of EAFS from the DRP-EAF-route and still significant amounts of BOFS from the DRP-SAF-BOF-route will be produced while BFS will vanish. In two BMBF funded research projects, BAM and FEhS examine the application of slags from future steel production in the cement industry. The project “SlagCEM” investigated the recovery of iron from BOFS while producing a mineral product with good cementitious properties. The reduction of BOFS to recover metallic iron along with the generation of a clinker-like material for the cement industry increases the viscosity of the BOFS. This would require a process at unfeasibly high temperatures of >1.700 °C. Therefore, SlagCEM aimed to modify the BOFS to reduce the viscosity to suitable ranges at lower temperatures of ~1.600 °C. A demonstration trial (20 tons) was carried out and the potential for substitution of OPC was determined. DRI-EOS investigates the utilization of increasing amounts of DRI-based EAFS in the cement industry to compensate the reduced production of GBFS. This requires an adjustment of the slag’s chemical composition and a rapid quenching to create an amorphous structure with latent hydraulic characteristics. The project studies the behavior of the modified slag during the metallurgical process and during solidification, any possibly negative impact on the cementitious or environmental properties as well as the potential to recover metals such as Fe, Cr, Mo and V. The final results of the project “SlagCEM”, finished in 2024, as well as the current state and insights of the project “DRI-EOS”, started in July 2022, shall be presented in this talk. T2 - 9th International Slag Valorisation Symposium CY - Leuven, Belgium DA - 08.04.2025 KW - Steel slags KW - Basic oxygen furnace (BOF) KW - Electric arc furnace (EAF) KW - Cement KW - Slag valorisation PY - 2025 AN - OPUS4-64712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 8. Nachtrag zum Zulassungsschein 12/BAM IV.3/09/00 für eine Schutzschicht bestehend aus einer sandgefüllten Schutzbahn für Kunststoffdichtungsbahnen in Deponieabdichtungen N2 - 8. Nachtrag zum Zulassungsschein 12/BAM IV.3/09/00 für eine Schutzschicht bestehend aus einer sandgefüllten Schutzbahn für Kunststoffdichtungsbahnen in Deponieabdichtungen der Fa. G quadrat GmbH, Krefeld. KW - Zulassung KW - Deponie KW - Schutzschicht KW - Kunststoffdichtungsbahn PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-604877 SP - 1 EP - 29 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60487 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 6. Nachtrag zum Zulassungsschein 08/BAM 4.3/02/14 für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen N2 - 6. Nachtrag zum Zulassungsschein für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen der Fa. Naue GmbH & Co. KG. KW - Deponie KW - Zulassung KW - Kunststoff-Dränelement PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601339 SP - 1 EP - 27 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60133 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 08/BAM IV.3/04/04 für eine geotextile Schutzlage als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen N2 - 3. Nachtrag zum Zulassungsschein für eine geotextile Schutzlage als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen der Fa. HUESKER Synthetic GmbH, Gescher. KW - Deponie KW - Zulassung KW - Schutzschicht PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601315 SP - 1 EP - 21 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60131 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 6. Nachtrag zum Zulassungsschein 08/BAM IV.3/08/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 6. Nachtrag zum Zulassungsschein für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Fa. Naue GmbH & Co. KG, Espelkamp. KW - Deponie KW - Zulassung KW - Geotextilien PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601324 SP - 1 EP - 19 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60132 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 11. Nachtrag zum Zulassungsschein 08/BAM 8.3/10/94 für eine Vliesstoffmatte als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen N2 - 11. Nachtrag zum Zulassungsschein für eine Vliesstoffmatte als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen der Fa. Naue GmbH & Co. KG. KW - Deponie KW - Zulassung KW - Schutzschicht PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601343 SP - 1 EP - 20 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60134 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 08/BAM IV.3/10/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 3. Nachtrag zum Zulassungsschein für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Fa. HUESKER Synthetic GmbH, Gescher. KW - Deponie KW - Zulassung KW - Geotextilien PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601307 SP - 1 EP - 25 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60130 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 06/BAM IV.3/03/07 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 3. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH, Bad Hall, Österreich. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601285 SP - 1 EP - 9 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 06/BAM IV.3/04/99 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 3. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH, Bad Hall, Österreich. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601298 SP - 1 EP - 6 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60129 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 1. Nachtrag zum Zulassungsschein 06/BAM 4.3/01/19 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 1. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH, Bad Hall, Österreich. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-601159 SP - 1 EP - 6 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Joachim A1 - Adamczyk, Burkart A1 - Ebert, D. A1 - Ehrenberg, A. A1 - Schraut, Katharina A1 - Gerlach, J. A1 - Wendt, K. A1 - Algermissen, D. A1 - Adam, Christian ED - Rogge, Andreas ED - Meng, Birgit T1 - Erzeugung von Bindemitteln aus Stahlwerksschlacken N2 - Die geplante Transformation der Stahlindustrie innerhalb der nächsten 20 Jahre hat aufgrund des mit ihr verbundenen Auslaufens der Hüttensanderzeugung Konsequenzen für die Zementindustrie, deren Abmilderung Gegenstand der Forschungsprojekte SlagCEM und DRI-EOS ist. Ersteres untersucht die Rückgewinnung von Eisen aus LD-Konverter-Schlacke bei gleichzeitiger Herstellung eines mineralischen Produktes mit zementä- ren Eigenschaften. Zweiteres befasst sich mit der Generierung eines Hüttensandersatzes aus Lichtbogen- ofenschlacke mit Rückgewinnung von Schwermetallen sowie deren Umwelteffekt bei Verbleib in der Schlacke. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Bindemittel KW - Stahlwerksschlacke PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613127 SN - 978-3-9818564-7-7 SP - 78 EP - 89 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61312 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 8. Nachtrag zum Zulassungsschein 08/BAM IV.3/12/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen N2 - 8. Nachtrag zum Zulassungsschein 08/BAM IV.3/12/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen der Firma HUESKER Synthetic GmbH, Gescher. KW - Deponie KW - Bewehrungsgitter KW - Abdichtungssystem PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624020 SP - 1 EP - 25 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62402 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 8. Nachtrag zum Zulassungsschein 08/BAM IV.3/11/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen N2 - 8. Nachtrag zum Zulassungsschein 08/BAM IV.3/11/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen der Firma Naue GmbH & Co. KG, Espelkamp. KW - Deponie KW - Bewehrungsgitter KW - Abdichtungssystem PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624056 SP - 1 EP - 24 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62405 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 11. Nachtrag zum Zulassungsschein 11/BAM IV.3/03/09 für ein Dichtungskontrollsystem (DKS) für Deponieoberflächenabdichtungen N2 - 11. Nachtrag zum Zulassungsschein 11/BAM IV.3/03/09 für ein Dichtungskontrollsystem (DKS) für Deponieoberflächenabdichtungen der Firma Sensor Dichtungs-Kontroll-Systeme GmbH, Bremen. KW - Deponie KW - Kunststoffdichtungsbahn KW - Dichtungskontrollsystem PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-611001 SP - 1 EP - 15 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61100 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 4. Nachtrag zum Zulassungsschein 08/BAM IV.3/10/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 4. Nachtrag zum Zulassungsschein 08/BAM IV.3/10/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Firma HUESKER Synthetic GmbH, Gescher. KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624038 SP - 1 EP - 19 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - Zulassungsschein 12/BAM 4.3/01/23 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - Zulassungsschein 12/BAM 4.3/01/23 für Kunststoffdichtungsbahnen in Basis- und Oberflächenabdichtungen von Deponien der Firma JUTA a. s., Tschechische Republik (deutscher Vertriebspartner: KAT GmbH, Wiesmoor). KW - Deponie KW - Kunststoffdichtungsbahn KW - Abdichtungssystem PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624049 SP - 1 EP - 16 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62404 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Walsh, Michael A1 - Schenk, Gerhard A1 - Robinson, Nicole A1 - John, Samuel A1 - Dayananda, Buddhi A1 - Krishnan, Vithya A1 - Adam, Christian A1 - Hermann, Ludwig A1 - Schmidt, Susanne T1 - The Circular Phosphorus Economy: Agronomic Performance of Recycled Fertilizers and Target Crops N2 - ABSTRACTBackgroundThe circular phosphorus (P) economy addresses economic and environmental penalties inherent to the current linear P economy. Phosphorus sources recovered from waste steams (recyclates) offer an alternative to conventional fertilizers.AimThis research aimed to assess the agronomic performance of P recyclates derived from wastewater (hazenite, struvite), treated sewage sludge ash (SSA) and compost (FOGO food organics/garden organics) with crops previously characterized for P use efficiency (PUE).MethodsPhosphorus was supplied as granules and benchmarked against conventional fertilizers or mineral solution. Grown in controlled conditions, crops received recyclates individually or as amalgamates, with or without additional water‐soluble P. We quantified P uptake, yield and phytate content, and calculated agronomic performance indicators.ResultsResults revealed that (1) crop genotypes with purportedly lower or higher PUE showed similar performance when grown with limiting P supply and/or less soluble P recyclates, (2) crop performance improved when less soluble P recyclates were combined with water‐soluble P, (3) crops produced similar yield and biomass when supplied with an organo‐mineral formulation, hazenite, or conventional fertilizer, (4) grain accumulated higher levels of the antinutrient phytate with excess soluble P.ConclusionWe conclude that suitably formulated P recyclates can supplement or replace conventional fertilizers, and that fertilizer design should consider the solubility of recyclates and a crop's ability to access less soluble P. This adds to the growing body of evidence that well‐formulated next‐generation fertilizers can efficiently nourish crops. Integrating insights from controlled experiments and field trials is a cost‐effective strategy to actualize the circular P economy. KW - Recycling fertilizer KW - Phosphate recovery KW - Sewage sludge ash KW - Struvite KW - Hazenite PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627116 DO - https://doi.org/10.1002/jpln.202400299 SP - 1 EP - 14 PB - Wiley AN - OPUS4-62711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 6. Nachtrag zum Zulassungsschein 13/BAM 4.3/04/12 für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen N2 - 6. Nachtrag zum Zulassungsschein 13/BAM 4.3/04/12 für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen der Firma Solmax Geosynthetics GmbH, Hamburg. KW - Deponie KW - Kunststoff-Dränelement KW - Abdichtungssystem PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628702 SP - 1 EP - 31 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62870 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 6. Nachtrag zum Zulassungsschein 02/BAM 4.3/03/12 für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen N2 - 6. Nachtrag zum Zulassungsschein 02/BAM 4.3/03/12 für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen der Firma Freudenberg Performance Materials GmbH & Co. KG, Erlenbach am Main. KW - Deponie KW - Kunststoff-Dränelement KW - Abdichtungssystem PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628693 SP - 1 EP - 34 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62869 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 7. Nachtrag zum Zulassungsschein 08/BAM IV.3/08/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 7. Nachtrag zum Zulassungsschein 08/BAM IV.3/08/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Firma Naue GmbH & Co. KG, Espelkamp. KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624075 SP - 1 EP - 17 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62407 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 9. Nachtrag zum Zulassungsschein 08/BAM IV.3/12/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen N2 - 9. Nachtrag zum Zulassungsschein 08/BAM IV.3/12/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen der Firma HUESKER Synthetic GmbH, Gescher. KW - Deponie KW - Bewehrungsgitter KW - Abdichtungssystem PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636691 SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-63669 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Adam, Christian A1 - Wöhlecke, Andreas T1 - 9. Nachtrag zum Zulassungsschein 08/BAM IV.3/11/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen N2 - 9. Nachtrag zum Zulassungsschein 08/BAM IV.3/11/10 für Bewehrungsgitter aus Kunststoff für Deponieoberflächenabdichtungen der Firma Naue GmbH & Co. KG, Espelkamp. KW - Deponie KW - Bewehrungsgitter KW - Abdichtungssystem PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636700 SP - 1 EP - 4 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-63670 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Erzeugung klimaschonender Bindemittel als Alternativen zu Zement N2 - Die Zementindustrie und weitere energieintensive Industrien wie etwa die Stahlindustrie stehen vor dem Hintergrund der Transformation unserer Gesellschaft zur Klimaneutralität vor erheblichen Herausforderungen. Ziel dieser Branchen ist perspektivisch die vollständige Vermeidung klimaschädlicher Emissionen – mit besonderem Fokus auf Kohlendioxid. Neben der Umstellung auf regenerative Energieträger, sind im Speziellen für die Zementindustrie die erheblichen Anteile an CO2-Emissionen durch die Entsäuerung von Kalkstein zukünftig zu vermeiden. Da die hervorragenden Bindemitteleigenschaften des bisher hauptsächlich in Zementen eingesetzten Portlandklinkers jedoch auf Calciumverbindungen wie Tri- und Di-calciumsilikaten basieren, stellt die Substitution des Kalks derzeit für die Zementindustrie die größte Herausforderung dar. Neben vollständig neuen Bindemittelsystemen ohne Verwendung von Kalk und CCS/CCU-Technologien zur Vermeidung der CO2-Emissionen bei Verwendung von Kalk, können Abfälle und Nebenprodukte wie etwa Betonbrechsand, verschiedene Schlacken und weitere Massenreststoffe sinnvoll zur Einsparung von Rohstoffen und zur Vermeidung von CO2-Emissionen eingesetzt werden. Es gilt diese Potentiale von Sekundärrohstoffen branchenübergreifend zu identifizieren und Synergien zwischen den Branchen nutzbar zu machen. Hierbei werden neben der chemischen Zusammensetzung der Abfälle und Nebenprodukte auch die Verfügbarkeit und der Massenstrom relevante Kriterien sein. Die potenziellen Sekundärrohstoffe und deren Gemische mit chemisch ähnlicher Zusammensetzung wie die bisher verwendeten Bindemittel, können durch verschiedene technische Ansätze wieder in reaktive Bindemittel umgewandelt und damit nutzbar gemacht werden. Eine gezielte Umwandlung der nicht reaktiven mineralischen Phasen in neue mineralische Phasen mit guten Bindemitteleigenschaften, kann u. a. durch Schmelzprozesse erzielt werden. In Schmelzen können bei hohen Temperaturen die bestehenden, nicht reaktiven mineralischen Phasen zerstört und neue mineralische Phasen mit guten Bindemitteleigenschaften erzeugt werden. Hohe Freiheitsgrade durch gezielte Einstellung der stofflichen Zusammensetzung der Schmelze, durch Stoffseparationen und durch geregelte Abkühlregimes können eine maßgeschneiderte Erzeugung neuer Bindemitteltypen ermöglichen. Aufgrund der hohen erforderlichen Temperaturen von Schmelzprozessen ist die Umsetzung dieser neuen Verfahren nach Möglichkeit in bestehenden pyrometallurgischen Produktionsrouten wie etwa der Stahlproduktion vorzunehmen. So kann etwa der Einsatz von Betonbrechsand als Schlackebildner in der Stahlproduktion zielführend sein, wenn die Schlacke wieder zu einem Bindemittel prozessiert wird und in Zementen Verwendung findet. Eine stoffliche Kreislaufführung wäre hiermit gegeben, wobei der Einsatz von Kalkstein als Schlackebildner oder Rohstoff für die Zementproduktion, und damit die entsprechenden CO2-Emissionen, vermieden werden. Die Entwicklung neuartiger Bindemittelsysteme auf Basis von Sekundärrohstoffen sollte von erforderlichen Anpassungen und neuen Entwicklungen in der Regelsetzung und Normung begleitet werden. Vor allem muss gewährleistet sein, dass die mit neuen Bindemitteln hergestellten Betone den hohen Anforderungen an Dauerhaftigkeit und Umweltverträglichkeit genügen. Des Weiteren sollte mit den etablierten Methoden, wie etwa der Lebenszyklusanalyse, untersucht werden, inwiefern und in welchem Umfang die neuen technischen Entwicklungen zu Nachhaltigkeit und Klimaschutz beitragen. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 25.04.2022 KW - Zement KW - Thermochemische Prozesse KW - Sekundärrohstoffe PY - 2022 AN - OPUS4-54738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Gewinnung von grünem Eisen und weiteren Wertstoffen aus Rotschlamm mittels Wasserstoffplasma N2 - Rotschlamm fällt in sehr großen Mengen bei der Herstellung von Aluminiumoxid an und wird fast ausschließlich deponiert. Es wird eine neue Technologie vorgestellt bei der das im Rotschlamm enthaltene Eisenoxid mittels Wasserstoffplasma reduziert wird. Es wird ein Reaktionsmechanismus über Titanomagnetit und Hercynit vorgeschlagen. T2 - Berliner Konferenz Metallkreisläufe CY - Berlin, Germany DA - 13.03.2024 KW - Rotschlamm KW - Wasserstoffplasma PY - 2024 AN - OPUS4-59722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Wiesler, F. A1 - Hund-Rinke, K. A1 - George, E. A1 - Greef, J.-M. A1 - Holz, F. A1 - Hölze, L.E. A1 - Hülsbergen, K.-J. A1 - Martin, S. A1 - Severin, K. A1 - Spielvogel, S. A1 - Geiger, P. A1 - Nawotke, C. A1 - Kehlenbeck, H. A1 - Schenkel, H. A1 - Adam, Christian A1 - Bloem, E. A1 - Frank, D. A1 - Goldbach, H.E. A1 - Heene, M. A1 - Kratz, S. A1 - Kruse, A. A1 - Möller, K. A1 - Pinnekamp, J. A1 - Schoumans, O.F. A1 - Vogel, Christian A1 - Wulf, S. T1 - Recyclingphosphate in der Düngung – Nutzen und Grenzen N2 - Weltweit werden etwa 80–85 % aller abgebauten Rohphosphate für die Produktion von Düngemitteln verwendet. Bei noch steigendem Bedarf an Phosphor (P) geht man derzeit davon aus, dass die weltweiten P-Reserven noch über 200 Jahre ausreichen. Um den P-Vorrat langfristig abzusichern, sollte der in Reststoffen enthaltene Phosphor möglichst umfänglich genutzt werden. Dieser Forderung trägt das von der Bundesregierung 2012 erstmals beschlossene Deutsche Ressourceneffizienzprogramm ProgRess Rechnung. Rohphosphat wird auch seitens der Europäischen Kommission aufgrundseiner ökonomischen Bedeutung und des unsicheren Angebots als „kritischer Rohstoff“ eingestuft. Vor diesem Hintergrund hat die Bundesregierung in der Verordnung zur Neuordnung der Klärschlammverwertung vom 27. September 2017 in Deutschland eine verpflichtende technische Rückgewinnung von Phosphor für Abwasserbehandlungsanlagen ab einer Ausbaugröße von 100.000 Einwohnerwerten (12 Jahre nach Inkrafttreten der Verordnung) bzw. ab einer Ausbaugröße von über 50.000 Einwohnerwerten (15 Jahre nach Inkrafttreten der Verordnung) vorgeschrieben. Die Verordnung enthält keine Vorgaben hinsichtlich der anzuwendenden Technologie bei der Phosphorrückgewinnung. Ausgenommen von der Rückgewinnungspflicht sind Klärschlämme mit niedrigen Phosphorgehalten (weniger als 20 Gramm Phosphor je Kilogramm Klärschlamm-Trockenmasse). Auch die im Jahre 2017 verabschiedeten neuen Rechtsvorschriften für die Düngung verlangen zukünftig einen nachhaltigen und ressourceneffizienten Umgang mit Nährstoffen bei der landwirtschaftlichen Erzeugung und schränken die P-Zufuhr insbesondere auf hoch versorgten Böden ein (Düngeverordnung vom 26. Mai 2017). Dies wird zu einem mehr am Pflanzenbedarf orientierten und ggf. vermehrt überbetrieblichen Einsatz von wirtschaftseigenen Düngern führen. Um den politischen und gesetzlichen Anforderungen gerecht zu werden, müssen einerseits wirksame und kosteneffiziente technische Verfahren zum P-Recycling (weiter)entwickelt werden. Andererseits müssen die Recyclingprodukte die Anforderungen für eine direkte Verwendung in der Landwirtschaft oder als Rohstoff für die Herstellung von Düngemitteln erfüllen. In dem vorliegenden Standpunkt wird zunächst der potenzielle Beitrag von Reststoffen zur Deckung des P-Bedarfs in der deutschen Pflanzenproduktion geschätzt. Für die wichtigsten Reststoffe werden technische Verfahren zur P-Rückgewinnung bzw. Aufarbeitung skizziert. Auf Basis der Anforderungen der Landwirtschaft bzw. der Düngemittelindustrie an die P-Recyclingprodukte werden deren Herstellungsverfahren bewertet. Schließlich wird der Regelungs- und Forschungsbedarf formuliert. KW - Phosphor KW - Düngemittel KW - Diffusive Gradients in thin films (DGT) PY - 2020 SP - 1 EP - 19 PB - Bundesministerium für Ernährung und Landwirtschaft (BMEL) CY - Berlin AN - OPUS4-51011 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hamann, Christopher A1 - Spanka, M. A1 - Stolle, Dirk A1 - Auer, G. A1 - Weingart, Eric A1 - Al-Sabbagh, Dominik A1 - Ostermann, Markus A1 - Adam, Christian T1 - Recycling of blast-furnace sludge by thermochemical treatment with spent iron(II) chloride solution from steel pickling N2 - One of the typical wastes produced in blast-furnace (BF) ironmaking is BF sludge, which mostly consists of carbon and iron oxides, but also contains toxic trace metals such as Zn, Pb, Cd, As, and Hg that render the material hazardous. Due to the lack of an established recycling process, BF sludges are landfilled, which is ecologically questionable and costly. Here, we investigate selective removal of Zn, Pb, and Cd from BF sludge by chlorination–evaporation reactions using thermodynamic modelling and laboratory-scale experiments. Specifically, BF sludge was thermochemically treated at 650–1000 °C with a spent iron(II) chloride solution from steel pickling and the effects of process temperature and retention time on removal of Zn, Pb, and Cd were investigated. Zinc and Pb were quantitatively removed from BF sludge thermochemically treated at 900–1000 °C, whereas Fe and C as well as other major elements were mostly retained. The Zn, Pb, and Cd contents in the thermochemically treated BF sludge could be lowered from ∼56 g/kg, ∼4 g/kg, and ∼0.02 g/kg to ≤0.7 g/kg, ≤0.02 g/kg, and ≤0.008 g/kg, respectively, thus rendering the processed mineral residue a non-hazardous raw material that may be re-utilized in the blast furnace or on the sinter band. KW - Blast-furnace sludge KW - Selective chlorination KW - Zinc chloride PY - 2021 DO - https://doi.org/https://doi.org/10.1016/j.jhazmat.2020.123511 SN - 0304-3894 VL - 402 IS - 123511 SP - 1 EP - 12 PB - Elsevier CY - Amsterdam AN - OPUS4-51141 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Smol, M. A1 - Adam, Christian A1 - Krüger, O. T1 - Use of nutrients from wastewater for the fertilizer industry - approaches towards the implementation of the circular economy (CE) N2 - More sustainable waste management practices are an important element in the Transformation towards a circular economy (CE). Activities in this area should be dedicated to all groups of waste, including those generated in the water and sewage sector. This paper presents the characteristics of sewage sludge ash (SSA) coming from Polish municipal waste incineration plants. Due to the high content of nutrients such as phosphorus (8.01% P2O5), calcium (5.11% CaO) and magnesium (2.75% MgO), the analyzed SSA may constitute a valuable source of raw materials for the fertilizer industry. Despite the good fertilizing properties of the SSA, in some cases the presence of heavy metals such as cadmium (0.74–1.4 mg/kg dry matter), lead (49.8–99 mg/kg dry matter), mercury (3.93 mg/kg dry matter) and arsenic (4.23–4.43 mg/kg dry matter) and poor bioavailability of P from SSA disqualifies this waste from direct use as a fertilizer. Therefore, it is necessary to look for methods that will allow the municipal SSA to be processed, for example, technologies for the extraction of phosphorus and the production of phosphate fertilizer. This way of SSA management is in the line with the CE assumptions, in which waste becomes a valuable source of secondary raw materials. Fertilizer produced from waste meeting quality, safety and labelling requirements and limits of organic, microbiological and physical contaminants will be able to be traded freely within the European Union (EU) and receive the CE marking. The idea of use of SSA for fertilizer purposes is consistent not only with the objectives of the CE but also with the Polish National Waste Management Plan 2022 and the Municipal Sewage Sludge Strategy 2019–2022, which emphasizes the necessity to maximize the use of biogenic substances contained in wastewater. Therefore, sustainable management of SSA, in particular its storage in a way enabling the recovery of phosphorus, should be promoted. KW - Wastewater KW - Circular economy KW - Fertilizer KW - Sewage sludge KW - Phosphorus PY - 2020 DO - https://doi.org/10.5004/dwt.2020.25113 VL - 1 SP - 1 EP - 9 PB - Desalination Publications CY - Hopkinton, MA 01748, USA AN - OPUS4-50646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus der Arbeit des Fachbeirats der BAM N2 - Es wird über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet. So wurde in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert. Die Unterarbeitsgruppe Fremdüberwachung in der Produktion hat getagt. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoffdichtungsbahnen, Kunststoff-Dränelemente und für die Fremdüberwachung kurz vorgestellt. T2 - 16. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 03.03.2020 KW - Deponie KW - Geogitter KW - Kunststoffdichtungsbahn PY - 2020 SN - 978-3-943443-49-3 VL - 16 SP - 35 EP - 43 PB - HTWK Leipzig CY - Leipzig AN - OPUS4-50507 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schraut, Katharina A1 - Weingart, Eric A1 - Hamann, C. T1 - Technische Möglichkeiten der Abfallvermeidung in der Stahlproduktion N2 - Bei der Stahlproduktion fallen verfahrensbedingt große Mengen an Nebenprodukten und Abfällen wie Stahlwerksschlacken, Filterstäube und Gichtgasschlämme an. Hohe Anteile dieser Stoffströme werden aufgrund ihrer Zusammensetzung immer noch deponiert, obwohl sie ein hohes Wertstoffpotential aufweisen. An der Bundesanstalt für Materialforschung und -prüfung (BAM) werden Verfahren untersucht und entwickelt, welche eine Verwertung und Kreislaufführung dieser Materialströme ermöglichen. Aus sogenannten Linz-Donawitz-(LD)-Schlacken können durch carbothermische Nachbehandlung Roheisen und ein dem Portlandzementklinker (PZK) ähnliches Bindemittel erzeugt werden. Aus Elektroofenstäuben und Gichtgasschlämmen kann Zink gewonnen und die Anteile an Eisen und Kohlenstoff in den Stahlproduktionsprozess zurückgeführt werden. Durch diese technischen Maßnahmen kann es gelingen die Deponierung von Abfällen der Stahlproduktion zukünftig deutlich zu reduzieren. T2 - Recy&Depotech 2020 CY - Online meeting DA - 18.11.2020 KW - Stahlwerksschlacke KW - Filterstaub KW - Gichtgasschlamm PY - 2020 SP - 1 EP - 9 PB - Montanuniversität Leoben CY - 8700 Leoben, Österreich AN - OPUS4-51605 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Technische Möglichkeiten der Abfallvermeidung in der Stahlproduktion N2 - Bei der Stahlproduktion fallen verfahrensbedingt große Mengen an Nebenprodukten und Abfällen wie Stahlwerksschlacken, Filterstäube und Gichtgasschlämme an. Hohe Anteile dieser Stoffströme werden aufgrund ihrer Zusammensetzung immer noch deponiert, obwohl sie ein hohes Wertstoffpotential aufweisen. An der Bundesanstalt für Materialforschung und -prüfung (BAM) werden Verfahren untersucht und entwickelt, welche eine Verwertung und Kreislaufführung dieser Materialströme ermöglichen. Aus sogenannten Linz-Donawitz-(LD)-Schlacken können durch carbothermische Nachbehandlung Roheisen und ein dem Portlandzementklinker (PZK) ähnliches Bindemittel erzeugt werden. Aus Elektroofenstäuben und Gichtgasschlämmen kann Zink gewonnen und die Anteile an Eisen und Kohlenstoff in den Stahlproduktionsprozess zurückgeführt werden. Durch diese technischen Maßnahmen kann es gelingen die Deponierung von Abfällen der Stahlproduktion zukünftig deutlich zu reduzieren. T2 - Recy&Depotech 2020 CY - Online meeting DA - 18.11.2020 KW - Stalwerksschlacke KW - Gichtgasschlamm KW - Filterstaub PY - 2020 AN - OPUS4-51607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus der Arbeit des Fachbeirats der BAM N2 - Es wird über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet. So wurde in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert. Die Unterarbeitsgruppe Fremdüberwachung in der Produktion hat getagt. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoffdichtungsbahnen, Kunststoff-Dränelemente und für die Fremdüberwachung kurz vorgestellt. T2 - 16. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 03.03.2020 KW - Deponie KW - Geogitter KW - Kunststoffdichtungsbahnen PY - 2020 AN - OPUS4-50509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. ED - Reiser, B. T1 - Recycling von metallurgischen Rückständen - Schmelzversuche zeigen, wie die Tantalrückgewinnung aus Zinnschlacken und weiteren Reststoffen optimiert werden kann N2 - Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment. In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided. Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases. N2 - Da das Recycling von tantalhaltigen Post-Consumer-Abfällen praktisch nicht existiert, stellen metallurgische Reststoffe eine äußerst wichtige Rohstoffquelle für das Tantalrecycling dar. Die meisten Zinnerze enthalten von Natur aus erhebliche Mengen an Refraktärmetallen. Diese Elemente werden in den Schlacken der pyrometallurgischen Primärzinngewinnung angereichert. Aufgrund ihrer vergleichsweise hohen Wertstoffkonzentration und ihrer Funktion als zusätzlicher Schlackenbildner stellen diese Schlacken einen wertvollen Rohstoff für die Verhüttung tantalhaltiger Reststoffe dar. In der vorliegenden Arbeit wird ein existierendes Verfahren zur Tantalrückgewinnung diskutiert, dem hauptsächlich pyrometallurgische Rückstände geringer Wertstoffkonzentration als Einsatzstoff dienen. Mit Hilfe des Verfahrens sollte dasoxidisch vorliegende Tantal vollständig reduziert und in der Metallphase angereichert werden. Weiterhin sollte vermieden werden, dass unerwünschte Elemente wie Titan in die Metallphase überführt werden. Ziel der Untersuchung war es, die ablaufenden Reduktionsprozesse besser zu verstehen, um so Ansätze für die Prozessoptimierung identifizieren zu können. KW - Lichtbogenofen KW - Pyrometallurgie KW - Recycling KW - Tantal KW - Zinnschlacke PY - 2020 SN - 0934-3482 VL - 33 SP - 10 EP - 17 PB - Rhombos-Verlag CY - Berlin AN - OPUS4-50656 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Taube, Mareike Carolin A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Feldmann, Ines A1 - Ostermann, Markus A1 - Reuter, M. A1 - Stelter, M. T1 - Tantalrecycling aus pyrometallurgischen Rückständen N2 - Gegenstand dieser Arbeit ist die Untersuchung eines bestehenden pyrometallurgischen Prozesses zur Rückgewinnung von Tantal und Niob aus metallurgischen Reststoffen mit vorwiegend niedriger Wertstoffkonzentration. Zur näheren Erforschung der im vorliegenden Stoffsystem ablaufenden Reduktionsprozesse wurden in einem Elektrolichtbogenofen Schmelzversuche im Pilotmaßstab durchgeführt. Als Reduktionsmittel diente Koks, welcher mithilfe einer Argon-gespülten Eisenlanze in die flüssige mineralische Schmelze eingebracht wurde. Während der Reduktionsbehandlung werden Refraktärmetalle wie Tantal und Niob in ihre Carbide überführt und anschließend in der erschmolzenen eisenbasierten Metallphase am Boden des Reaktors angereichert. Neben Tantal und Niob gelangt auch ein Teil des im Einsatzmaterial enthaltenen Titans als unerwünschtes Begleitelement in die Metallphase. Sein Großteil verbleibt jedoch als Oxid in der Schlacke und wird dort hauptsächlich im Mineral Perowskit (CaTiO3) gebunden. Die erstarrten Schlackeproben wurden mit verschiedenen Methoden wie Röntgenfluoreszensanalyse, Röntgenbeugung und Rasterelektronenmikroskopie mit gekoppelter energiedispersiver Röntgenanalyse untersucht, um die Bildung tantalhaltiger Mineralphasen zu verschiedenen Stadien des Reduktionsprozesses zu verfolgen. Die hier gewonnenen Erkenntnisse zeigen, dass weniger die durch das Einblasen von Koks verursachte Reduktionsreaktion, sondern das Absinken der tantalreichen Eisentröpfchen in der flüssigen mineralischen Schmelze, gefolgt von ihrer Anreicherung in die Metallphase, für die Kinetik ausschlaggebend ist. N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Melting experiments were carried out in a pilot-scale electric arc furnace to study the material system during the reduction process caused by blowing coke into the liquid mineral melt. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are converted into their carbides and enriched in the molten iron-based metal phase. Titanium is also enriched in the metal phase as an unwanted accompanying element, but most of it remains in oxidic form in the slag and is mainly bound in the mineral perovskite. Cooled down slag samples were analysed using XRF, XRD, SEM and EDX to investigate the formation of mineral phases rich in tantalum during various stages of the reduction process. The results show that the settling of the tantalum-rich iron droplets in the molten slag into the metal phase May play a greater role for the kinetics than the actual reduction reaction caused by blowing in coke. KW - Tantal KW - Recycling KW - Reduktionsprozess KW - Perowskit KW - Elektrolichtbogenofen PY - 2020 SN - 1613-2394 VL - 73 IS - 4 SP - 196 EP - 205 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-51064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Gypsum plasterboard recycling - a sustainable approach N2 - Gypsum (calcium sulfate dihydrate) has excellent building material properties and has been widely used in constructions in the last decades in many countries. Accordingly, an increase of waste gypsum in C&D waste is expected in the upcoming years. On one hand, sulfates are unwanted in other secondary building materials (particularly in recycled concrete aggregates) and should be minimized for quality reasons. On the other hand, used gypsum from CDW can also be used in gypsum production if the high quality requirements for the recycled gypsum – especially regarding the sorting accuracy - are met. A large percentage of the gypsum from buildings was installed as gypsum plasterboards in interior fittings so far. Gypsum plasterboards are comparatively simple to remove and to separate during selective dismantling. Therefore, a high sorting purity can be achieved. In addition, techniques for the recycling of gypsum plasterboards already exist and high quality standards can be achieved. Also, the reuse in gypsum production has been improved in the last decade. Furthermore, an environmental evaluation of the whole process of gypsum plasterboard recycling and reuse showed that this approach can be environmentally advantageous. Therefore, a closed-loop recycling of gypsum plasterboards is feasible. This poster will show the development of gypsum consumption in different countries as well as a prognosis for the upcoming of gypsum in CDW in the future decades in Germany. Furthermore, a simplified scheme of the recycling process and selected results from an environmental evaluation will be presented. T2 - Conference on Mining the European Anthroposphere: Poster session CY - Bologna, Italy DA - 20.02.2020 KW - LCA KW - Gypsum recycling PY - 2020 AN - OPUS4-51435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -