TY - JOUR
A1 - Montag, D.
A1 - Adam, Christian
T1 - Rechtliche Vorgaben der Klärschlammverordnung und deren Auswirkungen auf die Phosphor-Rückgewinnung
N2 - Im Abfalltechnik-Ausschuss der Bund/Länder-Arbeitsgemeinschaft Abfall (LAGA) wurde eine Vollzugshilfe zur Klärschlammverordnung erarbeitet, die nach Verabschiedung durch die Umweltministerkonferenz Mitte Mai 2020 als LAGA-Merkblatt M-39 veröffentlicht wurde. Im vorliegenden vierten Arbeitsbericht der DWA-Arbeitsgruppe KEK-1.1 werden verschiedene Aspekte der ab dem Jahr 2029 geltenden Regelungen aufgegriffen und damit einige Punkte des LAGA M-39 hinsichtlich der technischen Auswirkungen für den Kläranlagenbetreiber konkret ausgeführt.
KW - Klärschlamm
KW - Klärschlammverordnung
KW - Phosphor-Rückgewinnung
PY - 2022
SN - 1866-0029
VL - 5
IS - 69
SP - 406
EP - 413
PB - Gesellschaft zur Förderung der Abwassertechnik
CY - Hennef
AN - OPUS4-55009
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Raniro, H.R.
A1 - Soares, T.de M.
A1 - Adam, Christian
A1 - Pavinato, P.S.
T1 - Waste-derived fertilizers can increase phosphorus uptake by sugarcane and availability in a tropical soil
N2 - The use of highly water-soluble phosphorus (P) fertilizers can lead to P fixation in the soil, reducing fertilization efficiency. Waste-derived, low water-solubility sources can potentially increase sugarcane’s P uptake compared to triple superphosphate by reducing adsorption to the soil.
Aims:We aimed to test struvite, hazenite, and AshDec® for their agronomic potential as recycled fertilizers for sugarcane production in a typical tropical soil.We hypothesize that these sources can reduce P fixation in the soil, increasing its availability and sugarcane’s absorption.
Methods: In a greenhouse pot experiment, two consecutive sugarcane cycles, 90 days each, were conducted in a Ferralsol. The recovered sources struvite, hazenite, AshDec®, and the conventional triple superphosphate were mixed in the soil in three P doses (30, 60, and 90 mg kg–1), aside a control (nil-P). At both harvests, sugarcane number of sprouts, plant height, stem diameter, dry mass yield, shoot phosphorus, and soil P fractionation were investigated.
Results: At 90 days, struvite and hazenite performed better for dry mass yield (70.7 and 68.3 g pot–1, respectively) than AshDec® and triple superphosphate (59.8 and 57.4 g pot–1, respectively) and for shoot P, with 98.1, 91.6, 75.6, and 66.3 mg pot–1, respectively. At 180 days, struvite outperformed all treatments for dry mass yield (95.3 g pot–1) and AshDec® (75.5 mg pot–1) for shoot P. Struvite was 38% and hazenite 21% more efficient than triple superphosphate in P uptake, while AshDec® was 6% less efficient. Soil had higher labile P under struvite, hazenite, and AshDec® than triple superphosphate by the end of the first cycle, while only the later increased nonlabile P by the end of the experiment (180 days).
Conclusions:Waste-derived P sources were more efficient in supplying P for sugarcane and delivering labile P in 180 days than triple superphosphate.
KW - AshDec
KW - Hazenite
KW - P-efficiency
KW - Recycled sources
KW - Struvite
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-544216
DO - https://doi.org/10.1002/jpln.202100410
SN - 1436-8730
SP - 1
EP - 12
PB - Wiley-VCH GmbH
AN - OPUS4-54421
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Sichler, Theresa Constanze
A1 - Adam, Christian
A1 - Montag, D.
A1 - Barjenbruch, M.
T1 - Future nutrient recovery from sewage sludge regarding three different scenarios - German case study
N2 - Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, German wastewater treatment plants (WWTPs) must recover phosphorus (P) from sewage sludge if it contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs >100,000 population equivalents (pe) from 2029 and >50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 16% of the total disposal in 2019. The reports of 10 states were evaluated for 2016 and 2017 representing approx. 60% of the total agriculturally used sludge volume. In 2016, 60% of the WWTPs’ sludges exceeded the recovery limit of 2 wt % P which is 70% of the amount of sludge and 85% of the phosphorus load. Other nutrients are not affected by the recovery obligation. However, many P recovery processes recover other nutrients, too. Considering three different scenarios for future German sewage sludge disposal shows that 70–77% of the P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0–16% nitrogen, 36–52% of calcium, 31–53% of potassium, and 40–52% of magnesium. However, these recovered nutrients loads can substitute only 1% or less of the commercial fertilizer demand except from phosphorus which is up to 43% of the demand.
KW - Sewage sludge
KW - Phosphorus recovery
KW - Wastewater
KW - Sewage sludge disposal
PY - 2022
DO - https://doi.org/10.1016/j.jclepro.2021.130130
VL - 333
SP - 1
EP - 10
PB - Elsevier Ltd.
CY - Amsterdam
AN - OPUS4-54186
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Raniro, H.R.
A1 - Teles, A.P.
A1 - Pavinato, P.S.
A1 - Adam, Christian
T1 - Phosphorus solubility and dynamics in a tropical soil under sources derived from wastewater and sewage sludge
N2 - Conventional phosphate fertilizers are usually highly water-soluble and rapidly solubilize when moistened by the soil solution. However, if this solubilization is not in alignment with plants demand, P can react with the soil colloidal phase, becoming less available over time. This is more pronounced in acidic, oxidic tropical soils, with
high P adsorption capacity, reducing the efficiency of P fertilization. Furthermore, these fertilizers are derived from phosphate rock, a non-renewable resource, generating an environmental impact. To assess these concerns, waste-recycled P sources (struvite, hazenite and AshDec®) were studied for their potential of reducing P Fixation by the soil and improving the agronomic efficiency of the P fertilization. In our work, we compared the solubilization dynamics of struvite, hazenite, AshDec® to triple superphosphate (TSP) in a sandy clay loam Ferralsol, as well as their effect on solution pH and on soil P pools (labile, moderately-labile and non-labile) via an incubation experiment. Leaching columns containing 50 g of soil with surface application of 100 mg per column (mg col 1) of P from each selected fertilizer and one control (nil-P) were evaluated for 60 days. Daily leachate samples from the column were analyzed for P content and pH. Soil was stratified in the end and submitted to P
fractionation. All results were analyzed considering p < 0.05. Our findings showed that TSP and struvite promoted an acid P release reaction (reaching pHs of 4.3 and 5.5 respectively), while AshDec® and hazenite reaction was alkaline (reaching pHs of 8.4 and 8.5 respectively). Furthermore, TSP promoted the highest P release among all sources in 60 days (52.8 mg col 1) and showed rapid release dynamic in the beginning, while struvite and hazenite showed late release dynamics and lower total leached P (29.7 and 15.5 mg col 1 P respectively). In contrast, no P-release was detected in the leachate of the AshDec® over the whole trial period. Struvite promoted
the highest soil labile P concentration (7938 mg kg 1), followed by hazenite (5877 mg kg 1) and AshDec® (4468 mg kg 1), all higher than TSP (3821 mg kg 1), while AshDec® showed high moderately-labile P (9214 mg kg 1), reaffirming its delayed release potential.
KW - Phosphate dynamics
KW - Struvite
KW - Wastewater
KW - Sewage sludge ash
KW - CaNaPO4
KW - P speciation
PY - 2022
DO - https://doi.org/10.1016/j.jenvman.2021.113984
VL - 302
IS - Part A
SP - 113984
PB - Elsevier Ltd.
AN - OPUS4-53600
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Herzel, Hannes
A1 - Aydin, Zeynep
A1 - Adam, Christian
T1 - Crystalline phase analysis and phosphorus availability after thermochemical treatment of sewage sludge ash with sodium and potassium sulfates for fertilizer production
N2 - Phosphorus rich sewage sludge ash is a promising source to produce phosphorus recycling fertilizer. However, the low plant availability of phosphorus in these ashes makes a treatment necessary. A thermochemical treatment (800–1000 °C) with alkali additives transforms poorly plant available phosphorus phases to highly plant available calcium alkali Phosphates (Ca,Mg)(Na,K)PO4. In this study, we investigate the use of K2SO4 as additive to produce a phosphorus potassium fertilizer in laboratory-scale experiments (crucible). Pure K2SO4 is not suitable as high reaction temperatures are required due to the high melting point of K2SO4.
To overcome this barrier, we carried out series of experiments with mixtures of K2SO4 and Na2SO4 resulting in a lower economically feasible reaction temperature (900–1000 °C). In this way, the produced phosphorus potassium fertilizers (8.4 wt.% K, 7.6 wt.% P) was highly plant available for phosphorus indicated by complete extractable phosphorus in neutral ammonium citrate solution. The added potassium is, in contrast to sodium, preferably incorporated into silicates instead of phosphorus phases. Thus, the highly extractable phase (Ca,Mg)(Na,K)PO4 in the thermochemical products contain less potassium than expected. This preferred incorporation is confirmed by a pilot-scale trial (rotary kiln) and thermodynamic calculation.
KW - Phosphorus recovery
KW - Recycling fertilizer
KW - Calcium alkali phosphate
KW - Silicate
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-536276
DO - https://doi.org/10.1007/s10163-021-01288-3
SN - 1611-8227
IS - 23
SP - 2242
EP - 2254
PB - Springer
AN - OPUS4-53627
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Rieger, J.
A1 - Colla, V.
A1 - Matino, I.
A1 - Branca, T. A.
A1 - Stubbe, G.
A1 - Panizza, A.
A1 - Brondi, C.
A1 - Falsafi, M.
A1 - Hage, J.
A1 - Wang, X.
A1 - Voraberger, B.
A1 - Fenzl, T.
A1 - Masaguer, V.
A1 - Faraci, E. L.
A1 - di Sante, L.
A1 - Cirilli, F.
A1 - Loose, Florian
A1 - Thaler, C.
A1 - Soto, A.
A1 - Frittella, P.
A1 - Foglio, G.
A1 - di Cecca, C.
A1 - Tellaroli, M.
A1 - Corbella, M.
A1 - Guzzon, M.
A1 - Malfa, E.
A1 - Morillon, A.
A1 - Algermissen, D.
A1 - Peters, K.
A1 - Snaet, D.
T1 - Residue Valorization in the Iron and Steel Industries: Sustainable Solutions for a Cleaner and More Competitive Future Europe
N2 - The steel industry is an important engine for sustainable growth, added value, and high-quality employment within the European Union. It is committed to reducing its CO2 emissions due to production by up to 50% by 2030 compared to 1990′s level by developing and upscaling the technologies required to contribute to European initiatives, such as the Circular Economy Action Plan (CEAP) and the European Green Deal (EGD). The Clean Steel Partnership (CSP, a public–private partnership), which is led by the European Steel Association (EUROFER) and the European Steel Technology Platform (ESTEP), defined technological CO2 mitigation pathways comprising carbon direct avoidance (CDA), smart carbon usage SCU), and a circular economy (CE). CE ap-proaches ensure competitiveness through increased resource efficiency and sustainability and consist of different issues, such as the valorization of steelmaking residues (dusts, slags, sludge) for internal recycling in the steelmaking process, enhanced steel recycling (scrap use), the use of secondary carbon carriers from non-steel sectors as a reducing agent and energy source in the steelmaking process chain, and CE business models (supply chain analyses). The current paper gives an overview of different technological CE approaches as obtained in a dedicated workshop called “Resi4Future—Residue valorization in iron and steel industry: sustainable solutions for a cleaner and more competitive future Europe” that was organized by ESTEP to focus on future challenges toward the final goal of industrial deployment.
KW - Circular economy
KW - Steelmaking residues
KW - Clean steel
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-530350
DO - https://doi.org/10.3390/met11081202
VL - 11
IS - 8
SP - 1202
PB - MDPI
AN - OPUS4-53035
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Weimann, Karin
A1 - Adam, Christian
A1 - Buchert, M.
A1 - Sutter, J.
T1 - Environmental Evaluation of Gypsum Plasterboard Recycling
N2 - Gypsum is widely used in the construction sector and its worldwide consumption has been increasing for several decades. Depending on the life-time of the used gypsum products, an increase of gypsum in construction and demolition waste follows. Especially against the background of a circular economy, the recycling of waste gypsum is of growing importance. However, the use of recycled gypsum makes only sense if it is environmentally friendly. Therefore, an evaluation of the environmental impacts of an industrial-scale processing for the recycling of post-consumer gypsum waste was conducted. The evaluation was performed with an established life cycle assessment software. Original data provided by industry and complementary data from a database for life cycle assessments were used for the calculations. Two scenarios for recycled gypsum with different transportation distances were calculated. These results are compared with results of the environmental evaluation of gypsum derived from coal-fired power plants (FGD gypsum) and natural gypsum. The results show that utilization of recycled gypsum can be environmentally advantageous compared to the use of natural gypsum or FGD gypsum, especially in the impact categories land transformation and resource consumption (abiotic depletion potential). For most environmental impact categories the specific transportation distances have a strong influence.
KW - Gypsum plasterboards
KW - Gypsum waste
KW - Recycled gypsum
KW - Environmental evaluation
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-522321
DO - https://doi.org/10.3390/min11020101
SN - 2075-163X
VL - 11
IS - 2
SP - 101
PB - MDPI
CY - Basel, Schweiz
AN - OPUS4-52232
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Schraut, Katharina
A1 - Adamczyk, Burkart
A1 - Adam, Christian
A1 - Stephan, D.
A1 - Meng, Birgit
A1 - Simon, Sebastian
A1 - von Werder, Julia
T1 - Synthesis and characterisation of alites from reduced basic oxygen furnace slags
N2 - Basic oxygen furnace slags (BOFS) are by-products of the steelmaking process. Several researchers have studied the production of Portland cement clinker and metallic iron from BOFS via a reductive treatment.
In this study, we applied a carbothermal reduction of BOFS in a technical-scale electric arc furnace and characterised the clinker-like products. Those clinker-like non-metallic products (NMPs) had a chemical and mineralogical composition comparable to clinker for ordinary Portland cement (OPC) and contained large elongated alite crystals as major component. The pure NMPs reacted more slowly and achieved a lower degree of hydration compared with commercial OPC.
If the reactivity of the products can be further increased by employing specific adaptations, it can be used as a full clinker substitute for OPC. Nevertheless, it is also an option to use the material without further modifications as a cement component or concrete addition, which contributes to the strength development in both cases.
KW - BOFS
KW - Hydration products
KW - Thermal analysis
KW - X-ray diffraction
PY - 2021
DO - https://doi.org/10.1016/j.cemconres.2021.106518
SN - 0008-8846
VL - 147
SP - 6518
PB - Elsevier Ltd.
AN - OPUS4-52939
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Schraut, Katharina
A1 - Kargl, F.
A1 - Adam, Christian
A1 - Ivashko, O.
T1 - In situ synchrotron XRD measurements during solidification of a melt in the CaO–SiO2 system using an aerodynamic levitation system
N2 - Phase formation and evolution was investigated in the CaO–SiO2 system in the range of 70–80 mol% CaO. The samples were container-less processed in an aerodynamic levitation system and crystallization was followed in situ by synchrotron x-ray diffraction at the beamline P21.1 at the German electron synchrotron (DESY). Modification changes of di- and tricalcium silicate were observed and occurred at lower temperatures than under equilibrium conditions. Despite deep sample undercooling, no metastable phase formation was observed within the measurement timescale of 1 s. For the given cooling rates ranging from 300 K s−1 to about 1 K s−1, no decomposition of tricalcium silicate was observed. No differences in phase evolution were observed between reducing and oxidizing conditions imposed by the levitation gas (Ar and Ar + O2). We demonstrate that this setup has great potential to follow crystallization in refractory oxide liquids in situ. For sub-second primary phase formation faster detection and for polymorph detection adjustments in resolution have to be implemented.
KW - Aerodynamic levitation
KW - Calcium silicate
KW - Phase formation
KW - Oxide melts
KW - In situ synchrotron x-ray diffraction
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526952
DO - https://doi.org/10.1088/1361-648X/abf7e1
VL - 33
IS - 26
SP - 264003 (12pp)
PB - IOP Publishing
AN - OPUS4-52695
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gentzmann, Marie
A1 - Paul, Andrea
A1 - Serrano, Juan
A1 - Adam, Christian
T1 - Understanding scandium leaching from bauxite residues of different geological backgrounds using statistical design of experiments
N2 - The leaching behavior of scandium (Sc) from bauxite residues can differ significantly when residues of different geological backgrounds are compared. The mineralogy of the source rock and the physicochemical environment during bauxitization affect the association of Sc in the bauxite i.e., how Sc is distributed amongst different mineral phases and whether it is incorporated in and/or adsorbed onto those phases. The Sc association in the bauxite is in turn crucial for the resulting Sc association in the bauxite residue. In this study systematic leaching experiments were performed on three different bauxite residues using a statistical design of experiments approach. The three bauxite residues compared originated from processing of lateritic and karstic bauxites from
Germany, Hungary, and Russia. The recovery of Sc and Fe was determined by ICP-OES measurements. Mineralogical changes were analyzed by X-ray-diffraction and subsequent Rietveld refinement. The effects of various parameters including temperature, acid type, acid concentration, liquid-to-solid ratio and residence time were studied. A response surface model was calculated for the selected case of citric acid leaching of Hungarian bauxite residue. The investigations showed that the type of bauxite residue has a strong influence. The easily leachable fraction of Sc can vary considerably between the types, reaching ~20–25% in German Bauxite residue and ~50% in Russian bauxite residue. Mineralogical investigations revealed that a major part of this fraction was released from secondary phases such as cancrinite and katoite formed during Bayer processing of the bauxite.
The effect of temperature on Sc and Fe recovery is strong especially when citric acid is used. Based on the exponential relationship between temperature and Fe-recovery it was found to be particularly important for the selectivity of Sc over Fe. Optimization of the model for a maximum Sc recovery combined with a minimum Fe
recovery yielded results of ~28% Sc recovery at <2% Fe recovery at a temperature of 60 ◦C, a citric acid normality of 1.8, and a liquid-to-solid ratio of 16 ml/g. Our study has shown that detailed knowledge about the Sc association and distribution in bauxite and bauxite residue is key to an efficient and selective leaching of Sc
from bauxite residues.
KW - Bauxite residue
KW - Scandium
KW - Leaching
KW - Design of experiments
KW - Red mud
PY - 2022
DO - https://doi.org/10.1016/j.gexplo.2022.107041
SN - 0375-6742
VL - 2022
IS - 240
SP - 1
EP - 13
PB - Elsevier Science
CY - Amsterdam
AN - OPUS4-55531
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Sichler, Theresa Constanze
A1 - Adam, Christian
A1 - Barjenbruch, M.
A1 - Montag, D.
A1 - Mauch, Tatjana
A1 - Sommerfeld, Thomas
A1 - Ehm, J.H.
T1 - Variation of the element composition of municipal sewage sludges in the context of new regulations on phosphorus recovery in Germany
N2 - Phosphorus (P) recovery is obligatory for all sewage sludges with more than 20 g P/kg dry matter (DM) from 2029 in Germany. Nine wastewater treatment plants (WWTPs) were chosen to investigate variations of phosphorus contents and other parameters in sewage sludge over the year. Monthly sewage sludge samples from each WWTP were analyzed for phosphorus and other matrix elements (C, N, H, Ca, Fe, Al, etc.), for several trace elements (As, Cr, Mo, Ni, Pb, Sn) and loss of ignition. Among the nine WWTPs, there are four which have phosphorus contents both above and below the recovery limit of 20 g/kg DM along the year. Considering the average phosphorus content over the year, only one of them is below the limit. Compared to other matrix elements and parameters, phosphorus fuctuations are low with an average of 7% over all nine WWTPs. In total, only hydrogen and carbon are more constant in the sludge.
In several WWTPs with chemical phosphorus elimination, phosphorus fuctuations showed similar courses like iron and/or aluminum. WWTPs with chamber flter presses rather showed dilution efects of calcium dosage. As result of this study, monthly phosphorus measurement is highly recommended to determine whether a WWTP is below the
20 g/kg DM limit.
KW - Sewage sludge
KW - Phosphorus recovery
KW - Wastewater
KW - Phosphorus elimination
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557499
DO - https://doi.org/10.1186/s12302-022-00658-4
SN - 2190-4707
VL - 34
IS - 1
SP - 1
EP - 12
PB - Springer Nature
CY - Berlin
AN - OPUS4-55749
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Neuhold, S.
A1 - Algermissen, D.
A1 - Drissen, P.
A1 - Adamczyk, Burkart
A1 - Presoly, P.
A1 - Sedlazeck, K. P.
A1 - Schenk, J.
A1 - Raith, J. G.
A1 - Pomberger, R.
A1 - Vollprecht, D.
T1 - Tailoring the FeO/SiO2 Ratio in Electric Arc Furnace Slags to Minimize the Leaching of Vanadium and Chromium
N2 - Based on recently published research on leaching control mechanisms in electric arc furnace (EAF) slags, it is assumed that a FeO/SiO2 ratio of around one leads to low leached V and Cr concentrations. This ratio influences the mineral phase composition of the slag toward higher amounts of spinel and a lower solubility of calcium silicate phases by suppressing the formation of magnesiowuestite and highly soluble calcium silicate phases. To evaluate this hypothesis, laboratory and scaled up tests in an EAF pilot plant were performed on slag samples characterized by elevated V and Cr leaching and a high FeO/SiO2 ratio. Prior to the melting experiments, the optimum FeO/SiO2 ratio was calculated via FactSageTM. In the melting experiments, the ratio was adjusted by adding quartz sand, which also decreased the basicity (CaO/SiO2) of the slag. As a reference, remelting experiments without quartz sand addition were conducted and additionally, the influence of the cooling rate of the slag was examined. The remelted (without quartz sand) and the remelted modified slags (with quartz sand) were analyzed chemically and mineralogically and the leaching behavior was investigated. The modification of the slags yielded a minimized release of V and Cr, supporting the hypothesis that the FeO/SiO2 ratio influences the mineralogy and the leaching behavior.
KW - Electric arc furnace (EAF) slags
KW - FactSageTM calculations
KW - Leaching control mechanisms
KW - Melting experiments
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-571517
DO - https://doi.org/10.3390/app10072549
VL - 10
IS - 7
SP - 1
EP - 18
PB - MDPI
AN - OPUS4-57151
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Machado Ferreira de Araujo, F.
A1 - Duarte-Ruiz, D.
A1 - Saßnick, H.-D.
A1 - Gentzmann, Marie C.
A1 - Huthwelker, T.
A1 - Cocchi, C.
T1 - Electronic Structure and Core Spectroscopy of Scandium Fluoride Polymorphs
N2 - Microscopic knowledge of the structural, energetic, and electronic properties of scandium fluoride is still incomplete despite the relevance of this material as an intermediate for the manufacturing of Al−Sc alloys. In a work based on first-principles calculations and X-ray spectroscopy, we assess the stability and electronic structure of six computationally predicted ScF3 polymorphs, two of which correspond to experimentally resolved single-crystal phases. In the theoretical analysis based on density functional theory (DFT), we identify similarities among the polymorphs based on their formation energies, chargedensity distribution, and electronic properties (band gaps and density of states). We find striking analogies between the results obtained for the ow- and high-temperature phases of the material, indirectly confirming that the transition occurring between them mainly consists of a rigid rotation of the lattice. With this knowledge, we examine the X-ray absorption spectra from the Sc and F K-edge contrasting firstprinciples results obtained from the solution of the Bethe−Salpeter equation on top of all-electron DFT with high-energy-resolution fluorescence detection measurements. Analysis of the computational results sheds light on the electronic origin of the absorption maxima and provides information on the prominent excitonic effects that characterize all spectra. A comparison with measurements confirms that the sample is mainly composed of the high- and low-temperature polymorphs of ScF3. However, some fine details in the experimental results suggest that the probed powder sample may contain defects and/or residual traces of metastable polymorphs.
KW - Scandium
KW - X-ray spectroscopy
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-570727
DO - https://doi.org/10.1021/acs.inorgchem.2c04357
SN - 0020-1669
VL - 62
IS - 10
SP - 4238
EP - 4247
PB - ACS Publications
CY - Washington DC
AN - OPUS4-57072
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smol, M.
A1 - Adam, Christian
A1 - Kugler, Stefan
T1 - Analiza możliwości wykorzystania w Polsce popiołów ze spalania komunalnych osadów ściekowych na cele nawozowe
T1 - Use of municipal sewage sludge ash for fertilizing purposes. An analysis of possibilities in Poland
N2 - Popioły pochodzące z instalacji do spalania komunalnych osadów ściekowych, znajdującej się na terytorium Polski, poddano procesom termochemicznego przekształcania, dzięki czemu otrzymano produkty nawozowe spełniające kryteria dopuszczające je do obrotu jako nawozy mineralne. Ponadto dokonano analizy możliwości wykorzystania popiołów na cele nawozowe zgodnie z obecnie przyjętymi dokumentami strategicznymi i planistycznymi dotyczącymi gospodarki odpadami na poziomie krajowym i europejskim.
N2 - Ashes from thermal transformation of municipal sewage sludge were thermochem. modified at 1000°C in the presence of NaHCO3 and sewage sludge to obtain CaNaPO4 and reduce the content of heavy metals in the produced fertilizer. Its bioavailability was more than 99% higher than that of raw ashes (50%). The nutrient content was 13.56 % Ca, 6.33% P, 4.36% K and 5.0% Fe. The content of heavy metals in fertilizer products met the std. requirements and was exceeded only in the case of Pb (278.3 mg/kg d.m.).
KW - Ashes
KW - Waste
KW - Phosphorus
KW - Recovery
KW - Fertilizer
PY - 2020
DO - https://doi.org/10.15199/62.2020.8.14
VL - 99
IS - 8
SP - 1186
EP - 1191
AN - OPUS4-51267
LA - pol
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kaufmann, Felix E.D.
A1 - Hoffmann, Marie C.
A1 - Bachmann, Kai
A1 - Veksler, Ilya V.
A1 - Trumbull, Robert B.
A1 - Hecht, Lutz
T1 - Variations in composition, texture, and platinum group element mineralization in the lower group and middle group chromitites of the Northwestern Bushveld Complex, South Africa
N2 - Small-scale variations in mineral chemistry, textures, and platinum group element (PGE) mineralization were investigated in the Lower and Middle Group chromitite layers LG6, LG6a, MG1, MG2, and MG2 II from vertical drill core profiles at the Thaba mine in the northwestern limb of the Bushveld Complex. We present detailed geochemical profiles of chromite composition and chromite crystal size distribution curves to shed light on the processes of chromite accumulation and textural modification as well as mineralization. Multiple samples within each layer were assayed for PGE concentrations, and the respective platinum group mineral association was determined by mineral liberation analysis (MLA).
There is strong evidence for postcumulus changes in the chromitites. The crystal size distribution curves suggest that the primary chromite texture was coarsened by a combination of adcumulus growth and textural equilibration, while compaction of the crystal mush played only a minor role. Mineral compositions were also modified by postcumulus processes, but because of the very high modal amount of chromite and its local preservation in orthopyroxene oikocrysts, that phase retained much primary information. Vertical variations of chromite composition within chromitite layers and from one layer to another do not support the idea of chromite accumulation from crystal-rich slurries or crystal settling from a large magma chamber. Instead, we favor a successive buildup of chromitite layers by repeated injections of relatively thin layers of chromite-saturated magmas, with in situ crystallization occurring at the crystal mush-magma interface. The adcumulus growth of chromite grains to form massive chromitite required addition of Cr to the layers, which we attribute to downward percolation from the overlying magma.
The PGE concentrations are elevated in all chromitite layers compared to adjacent silicate rocks and show a systematic increase upward from LG6 (avg 807 ppb Ir + Ru + Rh + Pt + Pd + Au) to MG2 II (avg 2,062 ppb).
There are also significant internal variations in all layers, with enrichments at hanging and/or footwalls. The enriched nature of chromitites in PGEs compared to host pyroxenites is a General feature, independent of the layer thickness. The MLA results distinguish two principal groups of PGE mineral associations: the LG6, LG6, and MG1 are dominated by the malanite series, laurite, and PGE sulfarsenides, while the MG2 and MG2 II layers are characterized by laurite and PGE sulfides as well as Pt-Fe-Sn and PGE-Sb-Bi-Pb alloys. Differences in the PGE associations are attributed to postcumulus alteration of the MG2 and MG2 II layer, while the chromitites below, particularly LG6 and LG6a, contain a more pristine association.
KW - Bushveld Complex
KW - Chromitites
KW - Platinum
PY - 2019
DO - https://doi.org/10.5382/econgeo.4641
SN - 0361-0128
VL - 114
IS - 3
SP - 569
EP - 590
PB - Society of Economic Geologists
AN - OPUS4-48145
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Taube, Mareike Carolin
A1 - Adamczyk, Burkart
A1 - Adam, Christian
A1 - Feldmann, Ines
A1 - Ostermann, Markus
A1 - Reuter, M.
A1 - Stelter, M.
T1 - Tantalrecycling aus pyrometallurgischen Rückständen
N2 - Gegenstand dieser Arbeit ist die Untersuchung eines bestehenden pyrometallurgischen Prozesses zur Rückgewinnung von Tantal und Niob aus metallurgischen Reststoffen mit vorwiegend niedriger Wertstoffkonzentration.
Zur näheren Erforschung der im vorliegenden Stoffsystem ablaufenden Reduktionsprozesse wurden in einem Elektrolichtbogenofen Schmelzversuche im Pilotmaßstab durchgeführt. Als Reduktionsmittel diente Koks, welcher mithilfe einer Argon-gespülten Eisenlanze in die flüssige mineralische Schmelze eingebracht wurde. Während der Reduktionsbehandlung werden Refraktärmetalle wie Tantal und Niob in ihre Carbide überführt und anschließend in der erschmolzenen eisenbasierten Metallphase am Boden des Reaktors angereichert. Neben Tantal und Niob gelangt auch ein Teil des im Einsatzmaterial enthaltenen Titans als unerwünschtes Begleitelement in die Metallphase.
Sein Großteil verbleibt jedoch als Oxid in der Schlacke und wird dort hauptsächlich im Mineral Perowskit (CaTiO3) gebunden. Die erstarrten Schlackeproben wurden mit verschiedenen Methoden wie Röntgenfluoreszensanalyse, Röntgenbeugung und Rasterelektronenmikroskopie mit gekoppelter energiedispersiver Röntgenanalyse untersucht, um die Bildung tantalhaltiger Mineralphasen zu verschiedenen Stadien des Reduktionsprozesses zu verfolgen.
Die hier gewonnenen Erkenntnisse zeigen, dass weniger die durch das Einblasen von Koks verursachte Reduktionsreaktion, sondern das Absinken der tantalreichen Eisentröpfchen in der flüssigen mineralischen Schmelze, gefolgt von ihrer Anreicherung in die Metallphase, für die Kinetik ausschlaggebend ist.
N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Melting experiments were carried out in a pilot-scale electric arc furnace to study the material system during the reduction process caused by blowing coke into the liquid mineral melt. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are converted into their carbides and enriched in the molten iron-based metal phase. Titanium is also enriched in the metal phase as an unwanted accompanying element, but most of it remains in oxidic form in the slag and is mainly bound in the mineral perovskite. Cooled down slag samples were analysed using XRF, XRD, SEM and EDX to investigate the formation of mineral phases rich in tantalum during various stages of the reduction process.
The results show that the settling of the tantalum-rich iron droplets in the molten slag into the metal phase May play a greater role for the kinetics than the actual reduction reaction caused by blowing in coke.
KW - Tantal
KW - Recycling
KW - Reduktionsprozess
KW - Perowskit
KW - Elektrolichtbogenofen
PY - 2020
SN - 1613-2394
VL - 73
IS - 4
SP - 196
EP - 205
PB - GDMB Verlag GmbH
CY - Clausthal-Zellerfeld
AN - OPUS4-51064
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smol, M.
A1 - Adam, Christian
A1 - Kugler, Stefan
T1 - Inventory of Polish municipal sewage sludge ash (SSA) – Mass flows, chemical composition, and phosphorus recovery potential
N2 - This paper presents an inventory of sewage sludge ashes (SSA) generated in the mono-incineration plants for municipal sewage sludge in Poland. This research focused on the detailed study of mass flows, chemical composition, and phosphorus recovery potential. There are currently 11 sludge mono-incineration plants operated with a total capacity of 160,300 Mg dry weight (d.w.) of sludge annually. Recently, a significant increase in the amount of SSA generated in these plants has been observed, reaching 26,756 Mg in 2018. Chemical composition of SSA showed significant amounts of the main nutrients: calcium (~14%), phosphorus (~13%), magnesium (~3%), and potassium (~1%). Additional main elements were iron (~14.5%), silicon (~13%), and aluminium (~6%). The main trace elements in the SSA were zinc (~3750 mg/kg) and copper (~899 mg/kg). Pollutants, according to fertilizer regulations of different countries, present in Polish SSA were chromium(~703 mg/kg), nickel (~260 mg/kg), lead (~94 mg/kg), and Cadmium (~9 mg/kg). The radionuclides, uranium, and thorium often present in higher amounts in commercial phosphate rock-based fertilizers, were only detected in SSA t low levels of 4–9 mg/kg and 2–3 mg/kg, respectively. Theoretical phosphorus recovery potential from the SSA (from plants in Cracow, Lodz, Gdansk, Gdynia, Szczecin, and Kielce) was estimated at 1613.8 Mg, of which 33.9% is bioavailable. Currently, in Poland, the recommended approach is the production of fertilizers as a result of the extraction of phosphorus from the SSA with its use in the production of secondary mineral fertilizers.
Further research in this area is required considering Polish conditions and legislation.
KW - Municipal sewage sludge
KW - Sewage sludge ash (SSA)
KW - Phosphorus
KW - Recovery potential
PY - 2020
DO - https://doi.org/10.1016/j.wasman.2020.07.042
VL - 116
SP - 31
EP - 39
PB - Elsevier Ltd
AN - OPUS4-51093
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Hamann, Christopher
A1 - Spanka, M.
A1 - Stolle, Dirk
A1 - Auer, G.
A1 - Weingart, Eric
A1 - Al-Sabbagh, Dominik
A1 - Ostermann, Markus
A1 - Adam, Christian
T1 - Recycling of blast-furnace sludge by thermochemical treatment with spent iron(II) chloride solution from steel pickling
N2 - One of the typical wastes produced in blast-furnace (BF) ironmaking is BF sludge, which mostly consists of carbon and iron oxides, but also contains toxic trace metals such as Zn, Pb, Cd, As, and Hg that render the material hazardous. Due to the lack of an established recycling process, BF sludges are landfilled, which is ecologically questionable and costly. Here, we investigate selective removal of Zn, Pb, and Cd from BF sludge by chlorination–evaporation reactions using thermodynamic modelling and laboratory-scale experiments. Specifically, BF sludge was thermochemically treated at 650–1000 °C with a spent iron(II) chloride solution from steel pickling and the effects of process temperature and retention time on removal of Zn, Pb, and Cd were investigated. Zinc and Pb were quantitatively removed from BF sludge thermochemically treated at 900–1000 °C, whereas Fe and C as well as other major elements were mostly retained. The Zn, Pb, and Cd contents in the thermochemically treated BF sludge could be lowered from ∼56 g/kg, ∼4 g/kg, and ∼0.02 g/kg to ≤0.7 g/kg, ≤0.02 g/kg, and ≤0.008 g/kg, respectively, thus rendering the processed mineral residue a non-hazardous raw material that may be re-utilized in the blast furnace or on the sinter band.
KW - Blast-furnace sludge
KW - Selective chlorination
KW - Zinc chloride
PY - 2021
DO - https://doi.org/https://doi.org/10.1016/j.jhazmat.2020.123511
SN - 0304-3894
VL - 402
IS - 123511
SP - 1
EP - 12
PB - Elsevier
CY - Amsterdam
AN - OPUS4-51141
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Adam, Christian
T1 - Phosphatdüngemittel aus Klärschlammaschen
N2 - Das Element Phosphor ist für alle Lebewesen essenziell und wird beispielsweise von Pflanzen in Form von Phosphaten aufgenommen.
In der landwirtschaftlichen Produktion werden dem Boden die Phosphate durch Wachstum und Ernte der Pflanzen entzogen und müssen ihm in Form von Phosphatdüngemitteln wieder zugeführt werden, um die Nahrungsmittelproduktion zu sichern. Rohphosphat stellt die Grundlage unserer derzeitigen Phosphatdüngemittel dar, ist aber gleichzeitig ein endlicher Rohstoff.
Des Weiteren sind insbesondere sedimentäre Rohphosphate oftmals mit erheblichen Konzentrationen toxischer Schadstoffe wie Cadmium, Uran und Thorium belastet. Eine Kreislaufführung des Phosphats sollte erfolgen, um natürliche Rohstoffvorkommen zu schonen und den Eintrag von Schadstoffen auf unsere Böden zu unterbinden.
KW - Phosphat
KW - Recyclingdüngemittel
PY - 2020
SN - 1610-6563
IS - 3
SP - 14
EP - 15
PB - MuP Verlag GmbH
CY - München
AN - OPUS4-50792
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smol, M.
A1 - Adam, Christian
A1 - Kugler, Stefan
T1 - Thermochemical Treatment of Sewage Sludge Ash (SSA)—Potential and Perspective in Poland
N2 - Phosphorus (P) recovery from sewage sludge ash (SSA) is one of the most promising approaches of phosphate rock substitution in mineral fertilizers and might be a sustainable way to secure supply of this raw material in the future. In the current investigation, the process of thermochemical treatment of SSA was applied to SSA coming from selected mono-incineration plants of municipal sewage sludge in Poland (Cracow, Gdansk, Gdynia, Lodz, Kielce and Szczecin).
The Polish SSA was thermochemically converted in the presence of sodium (Na) additives and a reducing agent (dried sewage sludge) to obtain secondary raw materials for the production of marketable P fertilizers. The process had a positive impact on the bioavailability of phosphorus and reduced the content of heavy metals in the obtained products. The P solubility in neutral Ammonium citrate, an indicator of its bioavailability, was significantly raised from 19.7–45.7% in the raw ashes and 76.5–100% in the thermochemically treated SSA. The content of nutrients in the recyclates was in the range of 15.7–19.2% P2O5, 10.8–14.2% CaO, 3.5–5.4% Na2O, 2.6–3.6% MgO and 0.9–1.3% K2O. The produced fertilizer raw materials meet the Polish norms for trace elements covered by the legislation: the content of lead was in the range 10.2–73.1 mg/kg, arsenic 4.8–22.7 mg/kg, Cadmium 0.9–2.8 mg/kg and mercury <0.05 mg/kg. Thus, these products could be potentially directly used for fertilizer production. This work also includes an analysis of the possibilities of using ashes for fertilizer purposes in Poland, based on the assumptions indicated in the adopted strategic and planning documents regarding waste management and fertilizer production.
KW - Sewage Sludge Ashes
KW - Critical raw materials
KW - Phosphorus
KW - Fertilizer
KW - Sewage Sludge
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514468
DO - https://doi.org/10.3390/en13205461
VL - 13
IS - 20
SP - 5461
AN - OPUS4-51446
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smol, M.
A1 - Adam, Christian
A1 - Krüger, O.
T1 - Use of nutrients from wastewater for the fertilizer industry - approaches towards the implementation of the circular economy (CE)
N2 - More sustainable waste management practices are an important element in the Transformation towards a circular economy (CE). Activities in this area should be dedicated to all groups of waste, including those generated in the water and sewage sector. This paper presents the characteristics of sewage sludge ash (SSA) coming from Polish municipal waste incineration plants. Due to the high content of nutrients such as phosphorus (8.01% P2O5), calcium (5.11% CaO) and magnesium (2.75% MgO), the analyzed SSA may constitute a valuable source of raw materials for the fertilizer industry.
Despite the good fertilizing properties of the SSA, in some cases the presence of heavy metals such as cadmium (0.74–1.4 mg/kg dry matter), lead (49.8–99 mg/kg dry matter), mercury (3.93 mg/kg dry matter) and arsenic (4.23–4.43 mg/kg dry matter) and poor bioavailability of P from SSA disqualifies this waste from direct use as a fertilizer. Therefore, it is necessary to look for methods that will allow the municipal SSA to be processed, for example, technologies for the extraction of phosphorus and the production of phosphate fertilizer. This way of SSA management is in the line with the CE assumptions, in which waste becomes a valuable source of secondary raw materials. Fertilizer produced from waste meeting quality, safety and labelling requirements and limits of organic, microbiological and physical contaminants will be able to be traded freely within the European Union (EU) and receive the CE marking. The idea of use of SSA for fertilizer purposes is consistent not only with the objectives of the CE but also with the Polish National Waste Management Plan 2022 and the Municipal Sewage Sludge Strategy 2019–2022, which emphasizes the necessity to maximize the use of biogenic substances contained in wastewater. Therefore, sustainable management of SSA, in particular its storage in a way enabling the recovery of phosphorus, should be promoted.
KW - Wastewater
KW - Circular economy
KW - Fertilizer
KW - Sewage sludge
KW - Phosphorus
PY - 2020
DO - https://doi.org/10.5004/dwt.2020.25113
VL - 1
SP - 1
EP - 9
PB - Desalination Publications
CY - Hopkinton, MA 01748, USA
AN - OPUS4-50646
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Taube, Mareike Carolin
A1 - Adam, Christian
A1 - Adamczyk, Burkart
A1 - Beckmann, T.
A1 - Reuter, M.
A1 - Stelter, M.
ED - Reiser, B.
T1 - Recycling von metallurgischen Rückständen - Schmelzversuche zeigen, wie die Tantalrückgewinnung aus Zinnschlacken und weiteren Reststoffen optimiert werden kann
N2 - Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment. In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided. Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases.
N2 - Da das Recycling von tantalhaltigen Post-Consumer-Abfällen praktisch nicht existiert, stellen metallurgische Reststoffe eine äußerst wichtige Rohstoffquelle für das Tantalrecycling dar. Die meisten Zinnerze enthalten von Natur aus erhebliche Mengen an Refraktärmetallen. Diese Elemente werden in den Schlacken der pyrometallurgischen Primärzinngewinnung angereichert. Aufgrund ihrer vergleichsweise hohen Wertstoffkonzentration und ihrer Funktion als zusätzlicher Schlackenbildner stellen diese Schlacken einen wertvollen Rohstoff für die Verhüttung tantalhaltiger Reststoffe dar. In der vorliegenden Arbeit wird ein existierendes Verfahren zur Tantalrückgewinnung diskutiert, dem hauptsächlich pyrometallurgische Rückstände geringer Wertstoffkonzentration als Einsatzstoff dienen. Mit Hilfe des Verfahrens sollte dasoxidisch vorliegende Tantal vollständig reduziert und in der Metallphase angereichert werden. Weiterhin sollte vermieden werden, dass unerwünschte Elemente wie Titan in die Metallphase überführt werden. Ziel der Untersuchung war es, die ablaufenden Reduktionsprozesse besser zu verstehen, um so Ansätze für die Prozessoptimierung identifizieren zu können.
KW - Lichtbogenofen
KW - Pyrometallurgie
KW - Recycling
KW - Tantal
KW - Zinnschlacke
PY - 2020
SN - 0934-3482
VL - 33
SP - 10
EP - 17
PB - Rhombos-Verlag
CY - Berlin
AN - OPUS4-50656
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Smol, M.
A1 - Adam, Christian
A1 - Preisner, M.
T1 - Circular economy model framework in the European water and wastewater sector
N2 - One of the key elements in the transformation towards a circular economy (CE) is providing more sustainable practices for resources and waste management. Improvement actions focused on transformation towards a CE should be targeted at all groups of materials and waste. As water is essential for human survival and well-being and plays a significant role in sustainable development (SD), the actions related to the reuse of water and the recovery of raw materials from wastewater and other water-based waste should be taken. The paper presents a proposition for a new CE model framework in the water and wastewater sector, which includes the six following actions: reduction—prevent wastewater generation in the first place by the reduction of water usage and pollution reduction at source; reclamation (removal)—an application of effective Technologies for the removal of pollutants from water and wastewater; reuse—reuse of wastewater as an alternative source of water supply (non-potable usage), recycling—recovery of water from wastewater for potable usage; recovery—recovery of resources such as nutrients and energy from water-based waste, and rethink—rethinking how to use resources to create a sustainable economy, which is `free` of waste and emissions. The novelty of the proposed CE model framework is that it presents possible ways of implementing CE principles in the water and wastewater sector, with a strong emphasis not only technological but also organisational and societal changes. Application of the proposed model may help to further transform the European economy to the CE model. Moreover, the indicated model can be significant tool supporting an assessment of local or regional progress towards CE in the water and wastewater sector and further environmental management and planning.
KW - Circular economy
KW - Phosphorus recovery
KW - Waste water
PY - 2020
DO - https://doi.org/10.1007/s10163-019-00960-z
SP - 1
EP - 16
PB - Springer
AN - OPUS4-50441
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Adamczyk, Burkart
A1 - Neuhold, S.
A1 - Drissen, P.
A1 - Algermissen, D.
A1 - Presoly, P.
A1 - Sedlazeck, K. P.
A1 - Schenk, J.
A1 - Raith, J. G.
A1 - Pomberger, R.
A1 - Vollprecht, D.
T1 - Tailoring the FeO/SiO2 ratio in electric arc furnace slags to minimize the leaching of Vanadium and Chromium
N2 - Based on recently published research on leaching control mechanisms in electric arc furnace (EAF) slags, it is assumed that a FeO/SiO2 ratio of around one leads to low leached V and Cr concentrations. This ratio influences the mineral phase composition of the slag toward higher amounts of spinel and a lower solubility of calcium silicate phases by suppressing the formation of magnesiowuestite and highly soluble calcium silicate phases. To evaluate this hypothesis, laboratory and scaled up tests in an EAF pilot plant were performed on slag samples characterized by elevated V and Cr leaching and a high FeO/SiO2 ratio. Prior to the melting experiments, the optimum FeO/SiO2 ratio was calculated via FactSageTM. In the melting experiments, the ratio was adjusted by adding quartz sand, which also decreased the basicity (CaO/SiO2) of the slag. As a reference, remelting experiments without quartz sand addition were conducted and additionally, the influence of the cooling rate of the slag was examined. The remelted (without quartz sand) and the remelted modified slags (with quartz sand) were analyzed chemically and mineralogically and the leaching behavior was investigated. The modification of the slags yielded a minimized release of V and Cr, supporting the hypothesis that the FeO/SiO2 ratio influences the mineralogy and the leaching behavior.
KW - Electric arc furnace slags
KW - FactSage calculations
KW - EAF slags
KW - Leaching control mechanisms
KW - Melting experiments
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507748
DO - https://doi.org/10.3390/app10072549
VL - 10
IS - 7
SP - 2549
EP - 2565
AN - OPUS4-50774
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Adam, Christian
T1 - Phosphor: Von der Rückgewinnung zum Recycling
N2 - Eine entscheidende Problematik nach Inkrafttreten der neuen
Klärschlammverordnung ist, wie Phosphor nicht nur rückgewonnen,
sondern in den Markt eingeschleust und letztlich auch
in den Kreislauf zurückgeführt werden kann. Die Wege hierzu
sind noch weitgehend ungeklärt. Die DWA-Arbeitsgruppe KEK-
1.1 hat aus diesem Grund einen Workshop durchgeführt, um
rechtliche Anforderungen an Rezyklate, Aspekte der Rezyklatqualität
und -beschaffenheit sowie den aktuellen Markt für Rezyklate
zu diskutieren. Auf Basis dieses Workshops wurde ein
Arbeitsbericht erstellt, der sich schwerpunktmäßig mit dem Einsatz
von Rezyklaten zu Düngezwecken beschäftigt. Hierzu liegen
bereits Erkenntnisse vor, und es sind bereits Praxisbeispiele in
der Umsetzung.
KW - Phosphor
KW - Klärschlamm
PY - 2018
DO - https://doi.org/10.3242/kae2018.08.005
SN - 1866-0029
VL - 65
IS - 8
SP - 710
EP - 717
PB - Gesellschaft zur Förderung der Abwassertechnik (GFA)
CY - Hennef
AN - OPUS4-45661
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Auer, G.
A1 - Spanka, M.
A1 - Hamann, Christopher
A1 - Adam, Christian
T1 - Thermal zinc extraction from steel mill dust
N2 - Treatment and reusing of hazardous wastes have become significant issues of modern societies. Blast furnace sludge (BFS) and electric arc furnace dust (EAFD) are such typical wastes, because they usually contain high amounts of undesirable elements such as zinc (Zn) and lead (Pb).
These elements can cause operational problems in reusing of BFS and EAFD. In this study, the Ferro Duo GmbH and the Federal Institute for Materials Research and Testing have investigated a novel approach for eliminating and/or recovering Zn and Pb from both wastes. Applied was a selective chlorination and volatilization of Zn and Pb as chlorides at temperatures between 500 °C and 1100 °C. Both product obtained, Zn and Pb in the form of ZnCl2 and PbCl2 and the purified solid mineral compound are attractive materials for further use. Hydrochloric acid and iron(II) chloride were used as chlorination agents. Exceptionally high Zn and Pb removal efficiencies of >99.5 % could be achieved with both chlorination agents, whereby iron(II) chloride exhibited better performance.
KW - Blast furnace sludge
KW - Chlorination
KW - Electric arc furnace dust
KW - Lead
KW - Zinc
KW - Thermochemical treatment
PY - 2019
SN - 1613-2394
VL - 72
IS - 1
SP - 27
EP - 31
PB - GDMB Verlag GmbH
CY - Clausthal-Zellerfeld
AN - OPUS4-47288
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Singh, Amit Kumar
A1 - Mishra, Biswajit
A1 - Sinha, Om Prakash
T1 - Reduction Kinetics of Fluxed Iron Ore Pellets Made of Coarse Iron Ore Particles
N2 - The present work demonstrates a sustainable approach of using relatively coarser iron ore particles for ironmaking. The motivation is to reduce the energy consumption in the milling of the iron ore by utilizing coarser iron ore particles (+0.05 mm) and to select a suitable binder for improving pellet properties. Iron ore fines in the range of 0.05–0.25 mm was selected and classified into three size ranges. Fluxed iron ore pellets were prepared using lime as a binder for the basicity of 0, 1, and 2. Reduction of these pellets with a packed bed of coal fines was performed in the temperature range of 900–1200 °C for a duration of 30–120 min. The direct reduction kinetics of the iron ore pellets were studied by employing diffusion and chemical reaction control models to the experimental data. The results show that pellets made with coarser iron ore particles have improved reduction behavior and kinetics. The reduction reaction is found to be a mixed control. The activation energy for the reduction reaction varies from 44.3 to 74.76 kJ mol−1 as iron ore particle size decreases from 0.25 to 0.05 mm and basicity increases from 0 to 2.
KW - Materials Chemistry
KW - Metals and Alloys
KW - Process Metallurgy
KW - Iron making
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-598326
DO - https://doi.org/10.1002/srin.202300669
SN - 1611-3683
IS - 2300669
SP - 1
EP - 9
PB - Wiley VHC-Verlag
AN - OPUS4-59832
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Jovičević-Klug, Matic
A1 - Souza Filho, Isnaldi R.
A1 - Springer, Hauke
A1 - Adam, Christian
A1 - Raabe, Dierk
T1 - Green steel from red mud through climate-neutral hydrogen plasma reduction
N2 - AbstractRed mud is the waste of bauxite refinement into alumina, the feedstock for aluminium production1. With about 180 million tonnes produced per year1, red mud has amassed to one of the largest environmentally hazardous waste products, with the staggering amount of 4 billion tonnes accumulated on a global scale1. Here we present how this red mud can be turned into valuable and sustainable feedstock for ironmaking using fossil-free hydrogen-plasma-based reduction, thus mitigating a part of the steel-related carbon dioxide emissions by making it available for the production of several hundred million tonnes of green steel. The process proceeds through rapid liquid-state reduction, chemical partitioning, as well as density-driven and viscosity-driven separation between metal and oxides. We show the underlying chemical reactions, pH-neutralization processes and phase transformations during this surprisingly simple and fast reduction method. The approach establishes a sustainable toxic-waste treatment from aluminium production through using red mud as feedstock to mitigate greenhouse gas emissions from steelmaking.
KW - Multidisciplinary
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594424
DO - https://doi.org/10.1038/s41586-023-06901-z
SN - 0028-0836
VL - 625
IS - 7996
SP - 703
EP - 709
PB - Springer Science and Business Media LLC
AN - OPUS4-59442
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Maulas, Kryzzyl M.
A1 - Paredes, Charla S.
A1 - Tabelin, Carlito Baltazar
A1 - Jose, Mark Anthony
A1 - Opiso, Einstine M.
A1 - Arima, Takahiko
A1 - Park, Ilhwan
A1 - Mufalo, Walubita
A1 - Ito, Mayumi
A1 - Igarashi, Toshifumi
A1 - Phengsaart, Theerayut
A1 - Villas, Edrhea
A1 - Dagondon, Sheila L.
A1 - Metillo, Ephrime B.
A1 - Uy, Mylene M.
A1 - Manua, Al James A.
A1 - Villacorte-Tabelin, Mylah
T1 - Isolation and Characterization of Indigenous Ureolytic Bacteria from Mindanao, Philippines: Prospects for Microbially Induced Carbonate Precipitation (MICP)
N2 - Microbially induced carbonate precipitation (MICP), a widespread phenomenon in nature, is gaining attention as a low-carbon alternative to ordinary Portland cement (OPC) in geotechnical engineering and the construction industry for sustainable development. In the Philippines, however, very few works have been conducted to isolate and identify indigenous, urease-producing (ureolytic) bacteria suitable for MICP. In this study, we isolated seven, ureolytic and potentially useful bacteria for MICP from marine sediments in Iligan City. DNA barcoding using 16s rDNA identified six of them as Pseudomonas stutzeri, Pseudomonas pseudoalcaligenes, Bacillus paralicheniformis, Bacillus altitudinis, Bacillus aryabhattai, and Stutzerimonas stutzeri but the seventh was not identified since it was a bacterial consortium. Bio-cementation assay experiments showed negligible precipitation in the control (without bacteria) at pH 7, 8, and 9. However, precipitates were formed in all seven bacterial isolates, especially between pH 7 and 8 (0.7–4 g). Among the six identified bacterial species, more extensive precipitation (2.3–4 g) and higher final pH were observed in S. stutzeri, and B. aryabhattai, which indicate better urease production and decomposition, higher CO2 generation, and more favorable CaCO3 formation. Characterization of the precipitates by scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) and attenuated total reflectance Fourier transform spectroscopy (ATR-FTIR) confirmed the formation of three carbonate minerals: calcite, aragonite, and vaterite. Based on these results, all six identified indigenous, ureolytic bacterial species from Iligan City are suitable for MICP provided that the pH is controlled between 7 and 8. To the best of our knowledge, this is the first report of the urease-producing ability and potential for MICP of P. stutzeri, P. pseudoalcaligenes, S. stutzeri, and B. aryabhattai.
KW - Calcium carbonate
KW - Microbially induced carbonate precipitation (MICP)
KW - Ureolytic bacteria
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-600888
DO - https://doi.org/10.3390/min14040339
VL - 14
IS - 4
SP - 1
EP - 15
PB - MDPI
AN - OPUS4-60088
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Stawski, Tomasz
A1 - Karafiludis, Stephanos
A1 - Pimentel, Carlos
A1 - Montes-Hernández, German
A1 - Kochovski, Zdravko
A1 - Bienert, Ralf
A1 - Weimann, Karin
A1 - Emmerling, Franziska
A1 - Scoppola, Ernesto
A1 - Van Driessche, Alexander E.S.
T1 - Solution-driven processing of calcium sulfate: The mechanism of the reversible transformation of gypsum to bassanite in brines
N2 - Here, we show that calcium sulfate dihydrate (gypsum) can be directly, rapidly and reversibly converted to calcium sulfate hemihydrate (bassanite) in high salinity solutions (brines). The optimum conditions for the efficient production of bassanite in a short time (<5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the better-known behaviour of the bassanite phase in low-salt environments. In low-salinity aqueous solutions, bassanite is considered to be metastable with respect to gypsum and anhydrite, and therefore gypsum-to-bassanite conversion does not occur in pure water. Interestingly, the high-salinity transformation of gypsum-to-bassanite has been reported by many authors and used in practice for several decades, although its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures was inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline phase for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios.
KW - Industrial and Manufacturing Engineering
KW - Strategy and Management
KW - General Environmental Science
KW - Renewable Energy, Sustainability and the Environment
KW - Building and Construction
KW - Calcium sulfate
KW - Gypsum
KW - Bassanite
KW - Scattering
KW - Raman
KW - In situ
KW - Synchrotron
KW - BESSY
KW - MySpot
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594698
UR - https://www.sciencedirect.com/science/article/pii/S0959652624004591#appsec1
DO - https://doi.org/10.1016/j.jclepro.2024.141012
SN - 0959-6526
VL - 440
SP - 1
EP - 12
PB - Elsevier B.V.
AN - OPUS4-59469
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Schraut, Katharina
A1 - Adamczyk, Burkart
A1 - Adam, Christian
A1 - Stephan, Dietmar
A1 - Meng, Birgit
A1 - Simon, Sebastian
A1 - von Werder, Julia
A1 - Hirsch, Tamino
A1 - Manninger, Tanja
T1 - Effect of gypsum on the hydration of fused cement clinker from basic oxygen furnace slag
N2 - Fused cement clinker can be produced from molten basic oxygen furnace slag (BOFS) by way of a reductive thermochemical treatment. During the thermochemical treatment, oxidic iron is reduced to metallic iron and separated. The resulting low-iron slag has a chemical and mineralogical composition similar to ordinary Portland cement (OPC) clinker. In this study, the hydraulic reactivity of the fused clinker from BOFS with and without gypsum was investigated using isothermal calorimetry, differential scanning calorimetry, in situ X-ray diffraction and powder X-ray diffraction. Furthermore, a synthetic fused clinker without foreign ions and fused clinker produced by a mixture of both materials was studied. The hydraulic reaction of the fused clinker from BOFS was considerably slower than that of OPC. However, the reaction can be accelerated by adding gypsum as a sulfate carrier. Furthermore, the results showed an increased reaction rate with decreasing content of foreign ions such as Fe, P or Mn.
KW - General Materials Science
KW - Building and Construction
PY - 2024
DO - https://doi.org/10.1680/jadcr.23.00070
SN - 0951-7197
SP - 1
EP - 19
PB - Telford
AN - OPUS4-59391
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Hamann, Christopher
A1 - Piehl, Patrick
A1 - Weingart, Eric
A1 - Stolle, Dirk
A1 - Al-Sabbagh, Dominik
A1 - Ostermann, Markus
A1 - Auer, Gerhard
A1 - Adam, Christian
T1 - Selective removal of zinc and lead from electric arc furnace dust by chlorination–evaporation reactions
N2 - Re-melting of scrap in an electric arc furnace (EAF) results in the accumulation of filter dust from off-gas treatment that predominantly consists of iron and zinc oxides. Filter dust is classified as hazardous waste due to its high contents of potentially toxic or ecotoxic elements such as Pb, Cr, Cd, and As. A promising processing route for this waste is selective chlorination, in which the non-ferrous metal oxides are chlorinated and selectively evaporated in form of their respective chlorides from the remaining solids via the process gas flow. Here, we investigate stepwise thermochemical treatment of EAF dust with either waste iron(II) chloride solution or hydrochloric acid at 650, 800, and 1100 ◦C. The Zn and Pb contents of the thermochemically processed EAF dust could be lowered from 29.9% and 1.63% to 0.09% and 0.004%, respectively. Stepwise heating allowed high separation between zinc chloride at the 650 ◦C step and sodium-, potassium-, and lead-containing chlorides at higher temperatures. Furthermore, the lab-scale results were transferred to the use of an experimental rotary kiln highlighting the possibilities of upscaling the presented process. Selective chlorination of EAF dust with liquid chlorine donors is, therefore, suggested as a potential recycling method for Zn-enriched steelworks dusts.
KW - Electric arc furnace dust
KW - Zinc
KW - Selective Chlorination
KW - Hazardous waste
KW - Resource Recovery
PY - 2024
DO - https://doi.org/10.1016/j.jhazmat.2023.133421
SN - 0304-3894
VL - 465
SP - 1
EP - 13
PB - Elsevier
AN - OPUS4-59345
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Sichler, Theresa Constanze
A1 - Adam, Christian
A1 - Becker, Roland
A1 - Sauer, Andreas
A1 - Ostermann, Markus
A1 - Barjenbruch, M.
T1 - Phosphorus determination in sewage sludge: comparison of different aqua regia digestion methods and ICP-OES, ICP-MS and photometric determination
N2 - Phosphorus recycling from sewage sludge will be obligatory in Germany from 2029. Phosphorus content determination in sewage sludge is crucial to assess the prescribed recycling rates. Currently, German law regards sample preparation using aqua regia digestion in a microwave or under reflux conditions as well as instrumental phosphorus determination by ICP-OES, ICP-MS, or photometric determination with ammonium molybdate as equivalent. However, it is questionable whether these methods are indeed equivalent regarding phosphorus quantification in sludges near the limit of 20 g/kg for mandatory recycling. To answer this question, 15 sewage sludges of 11 different wastewater treatment plants were investigated with all permitted method (digestion and measurement) combinations. Moreover, one sewage sludge was also examined in an interlaboratory comparison (ILC) with 28 participants. This study shows that the above-mentioned methods differ in some cases significantly but across all method combinations and sludges, phosphorus recovery was between 80 and 121% after normalization to the grand mean (average of 15 sludges between 85 and 111%). The ILC and the examination of 15 sludges produced largely similar results. There is a tendency to higher phosphorus recovery after microwave digestion compared to reflux digestion and ICP-OES measurements determine higher phosphorus contents than ICP-MS and photometric phosphorus determination. As a result, the authors recommend ICP-OES determination of phosphorus in sewage sludge after microwave digestion.
KW - Sewage sludge
KW - ICP-OES
KW - Phosphous recovery
KW - ICP-MS
KW - Photometric P determination
KW - Interlaboratory comparison
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-558869
DO - https://doi.org/10.1186/s12302-022-00677-1
VL - 34
IS - 99
SP - 1
EP - 14
PB - Springer
AN - OPUS4-55886
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Vogel, Christian
A1 - Rivard, C.
A1 - Wilken, V.
A1 - Muskolus, A.
A1 - Adam, Christian
T1 - Performance of secondary P-fertilizers in pot experiments analyzed by phosphorus X-ray absorption near-edge structure (XANES) spectroscopy
N2 - A pot experiment was carried out with maize to determine the phosphorus (P) plant-availability of different secondary P-fertilizers derived from wastewater. We analyzed the respective soils by P K-edge X-ray absorption near-edge structure (XANES) spectroscopy to determine the P chemical forms that were present and determine the transformation processes. Macro- and micro-XANES spectroscopy were used to determine the chemical state of the overall soil P and identify P compounds in P-rich spots. Mainly organic P and/or P adsorbed on organic matter or other substrates were detected in unfertilized and fertilized soils. In addition, there were indications for the formation of ammonium phosphates in some fertilized soils. However, this effect was not seen in the maize yield of all P-fertilizers. The observed reactions between phosphate from secondary P-fertilizers and cofertilized nitrogen compounds should be further investigated. Formation of highly plant-available compounds such as ammonium phosphates could make secondary P-fertilizers more competitive to commercial phosphate rock-based fertilizers with positive effects on resources conservation.
KW - Phosphorus
KW - Pot experiments
KW - Secondary P-fertilizer
KW - Sewage sludge ash
KW - Soil
KW - X-ray absorption near-edge structure (XANES) spectroscopy
PY - 2018
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-433782
DO - https://doi.org/10.1007/s13280-017-0973-z
SN - 0044-7447
VL - 47
IS - 1
SP - 62
EP - 72
PB - Springer
AN - OPUS4-43378
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Vogel, Christian
A1 - Hermann, P.
A1 - Kästner, B.
A1 - Adamczyk, Burkart
A1 - Hoehl, A.
A1 - Ulm, G.
A1 - Adam, Christian
T1 - Air and chlorine gas corrosion of different silicon carbides analyzed by nano-Fourier-transform infrared (nano-FTIR) spectroscopy
N2 - The present study shows the potential of high-resolution imaging and nano-Fourier-transform infrared (nano-FTIR) spectroscopy for corrosion science. The protective oxidation layers of different chlorine-gas treated silicon
carbides (SiCs) were characterized with these techniques. A nitrified SiC showed the highest resistant strength against chlorine corrosion at 1000 °C compared to the other SiCs. Nano-FTIR spectroscopy with a lateral resolution below 40 nm detected differences in the crystallinity of the bulk-SiC and in the transitional region to the protective layer. Furthermore, high-resolution imaging provides deep insight in the interfacial layer between bulk-SiC and the protective oxidation layer on sub-micrometer scale.
KW - Nano-Fourier-transform infrared spectroscopy
KW - Scattering-type scanning near-field optical microscopy (s-SNOM)
KW - Synchrotron radiation
KW - Corrosion
KW - Silicon carbide
KW - Chlorine
PY - 2018
DO - https://doi.org/10.1016/j.corsci.2017.12.002
SN - 0010-938X
VL - 131
SP - 324
EP - 329
PB - Elsevier
AN - OPUS4-43648
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Vogel, Christian
A1 - Doolette, A.
A1 - Huang, J.
T1 - Combining diffusive gradients in thin-films (DGT) and 31P NMR spectroscopy to determine phosphorus species in soil
N2 - The diffusive gradients in thin-films (DGT) technique shows in many publications a superior correlation to the amount of plant-available phosphorus (P) in soil. However, this technique cannot give information on the plant-available P species in soil. Therefore, we combined DGT with solution 31P nuclear magnetic resonance (NMR) spectroscopy. This was achieved by using a modified DGT device in which the diffusive layer had a larger pore size, the binding layer incorporated an adsorption material with a higher capacity, and the device had a larger exposure area. The spectroscopic investigation was undertaken after elution of the deployed DGT binding layer in a NaOH solution. Adsorption tests using solutions of known organic P compounds showed that a sufficient amount of these compounds could be adsorbed on the binding layer in order for them to be analyzed by solution 31P NMR spectroscopy. Furthermore, various intermediates of the hydrolysis of trimetaphosphate in soil could be also analyzed over time.
KW - Phosphorus
KW - Diffusive gradients in thin-films (DGT)
KW - Passive sampling
KW - fertilizer
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-545759
DO - https://doi.org/10.1002/ael2.20068
VL - 7
IS - 1
SP - e20068
PB - Wiley online library
AN - OPUS4-54575
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Vogel, Christian
A1 - Roesch, Philipp
A1 - Wittwer, Philipp
A1 - Piechotta, Christian
A1 - Lisec, Jan
A1 - Sommerfeld, Thomas
A1 - Kluge, Stephanie
A1 - Herzel, Hannes
A1 - Huthwelker, T.
A1 - Borca, C.
A1 - Simon, Franz-Georg
T1 - Levels of per- and polyfluoroalkyl substances (PFAS) in various wastewater-derived fertilizers - Analytical investigations from different perspectives
N2 - Solid wastewater-based fertilizers were screened for per- and polyfluoroalkyl substances (PFAS) by the extractable organic fluorine (EOF) sum parameter method. The EOF values for ten sewage sludges from Germany and Switzerland range from 154 to 7209 mg kg−1. For thermal treated sewage sludge and struvite the EOF were lower with values up to 121 mg kg−1. Moreover, the application of PFAS targeted
and suspect screening analysis of selected sewage sludge samples showed that only a small part of the EOF sum parameter values can be explained by the usually screened legacy PFAS. The hitherto unknown part of EOF sum parameter contains also fluorinated pesticides, pharmaceutical and aromatic compounds. Because these partly fluorinated compounds can degrade to (ultra-)short PFAS in wastewater treatment plants they should be considered as significant sources of organic fluorine in the environment. The combined results of sum parameter analysis and suspect screening reveal the need to update current regulations, such as the German fertilizer ordinance, to focus not solely on a few selected PFAS such as perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) but
consider an additional sum parameter approach as a more holistic alternative. Moreover, diffusion gradient in thin-films (DGT) passive samplers were utilized as an alternative simplified extraction method for PFAS in solid wastewater-based fertilizers and subsequently quantified via combustion ion chromatography. However, the DGT method was less sensitive and only comparable to the EOF values
of the fertilizers in samples with >150 mg kg−1, because of different diffusion properties for various PFAS, but also kinetic exchange limitations.
KW - Combustion ion chromatography
KW - Per- and polyfluoroalkyl substances (PFAS)
KW - Sewage sludge
KW - Fertilizer
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-583429
DO - https://doi.org/10.1039/d3va00178d
SN - 2754-7000
VL - 2
IS - 10
SP - 1436
EP - 1445
PB - Royal Society of Chemistry (RSC)
CY - London
AN - OPUS4-58342
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Herzel, Hannes
A1 - Grevel, K.-D.
A1 - Emmerling, Franziska
A1 - Dachs, E.
A1 - Benisek, A.
A1 - Adam, Christian
A1 - Majzlan, J.
T1 - Thermodynamic properties of calcium alkali phosphates Ca(Na,K)PO4
N2 - Calcium alkali phosphates Ca(Na,K)PO4 are main constituents of bioceramics and thermochemically produced phosphorus fertilizers because of their bioavailability. Sparse thermodynamic data are available for the endmembers CaNaPO4 and CaKPO4. In this work, the missing data were determined for the low-temperature phase modifications of the endmembers CaNaPO4 and CaKPO4 and three intermediate Ca(Na,K)PO4 compositions. Standard enthalpy of formation ranges from - 2018.3 ± 2.2 kJ mol-1 to - 2030.5 ± 2.1 kJ mol-1 and standard entropy from 137.2 ± 1.0 J mol-1 K-1 to 148.6 ± 1.0 J mol-1 K-1 from sodium endmember b-CaNaPO4 to potassium endmember b0-CaKPO4.
Thermodynamic functions are calculated up to 1400 K for endmembers and the sodium-rich intermediate phase b-Ca(Na0.93K0.07)PO4. Functions above 640 K are extrapolated because of the phase transition from low- to high-temperature phase. Impurities in the synthesized intermediate phases c-Ca(Na0.4K0.6)PO4 and c-Ca Na0.35K0.65)PO4 and one additional phase transition around 500 K impeded the determination of high-temperature thermodynamic functions. In general, data for phase transition temperatures agree with the previously reported phase diagrams.
KW - Formation enthalpy
KW - Heat capacity
KW - Phase transformation
KW - Bioceramics
KW - Phosphorus fertilizer
KW - Entropy
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507640
DO - https://doi.org/10.1007/s10853-020-04615-5
VL - 55
SP - 8477
EP - 8490
PB - Springer
AN - OPUS4-50764
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Herzel, Hannes
A1 - Dombinov, V.
A1 - Vogel, Christian
A1 - Willbold, S.
A1 - Levandowski, G. V.
A1 - Meiller, M.
A1 - Müller, F.
A1 - Zang, J. W.
A1 - da Fonseca-Zang, W. A.
A1 - Jablonowski, N. D.
A1 - Schrey, S. D.
A1 - Adam, Christian
T1 - Soybean Fertilized by P-Phases from Bagasse-Based Materials: P-Extraction Procedures, Diffusive Gradients in Thin Films (DGT), and X-ray Diffraction Analysis (XRD)
N2 - The Brazilian sugarcane industry produced around 173 million tons (Mt) of bagasse in 2018. Bagasse is a by-product of juice extraction for ethanol and sugar production and is combusted in order to generate power, producing up to 10 Mt of ash per year. This ash contains various concentrations of plant nutrients, which allow the ash to be used as a crop fertilizer. However, the concentration and extractability of phosphorus (P), an essential plant nutrient, are low in bagasse ash. To increase the P content, we co-gasified and co-combusted bagasse with P-rich chicken manure. The resulting ash was thermochemically post-treated with alkali additives (Na2SO4 and K2SO4) to increase the availability of P to plants. We aimed to: (i) investigate the effect of thermochemical post-treatment of co-gasification residue and co-combustion ash on P availability to soybeans, (ii) explore the potential of chemical extraction methods (citric acid, neutral ammonium citrate, formic acid, and Mehlich-I) and diffusive gradients in thin films (DGT) to predict the availability of P to soybeans, and (iii) identify the responsible P-phases using X-ray diffraction . We evaluated P availability to soybeans growing in Brazilian Oxisol soil in two independent greenhouse pot experiments. The positive effect of thermochemical treatment on P availability from gasification residue was confirmed through the observation of increased P uptake and biomass in soybean plants. These findings were confirmed by chemical extraction methods and DGT. The gasification residue contained whitlockite as its main P-bearing phase. Thermochemical post-treatment converted whitlockite into highly soluble CaNaPO4. In contrast, co-combustion ash already contained highly soluble Ca(Na,K)PO4 as its main P-bearing phase, making thermochemical post-treatment unnecessary for increasing P availability. In conclusion, increased extractability and availability of P for soybeans were closely connected to the formation of calcium alkali phosphate. Our findings indicate that this combined methodology allows for the prediction of P-fertilization effects of ash.
KW - Sugar cane bagasse
KW - Chicken manure ash
KW - Thermochemical treatment
KW - Nutrient
KW - Plant availability
PY - 2020
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509735
DO - https://doi.org/10.3390/agronomy10060895
VL - 10
SP - 895
EP - 6
PB - MDPI
AN - OPUS4-50973
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Dombinov, V.
A1 - Herzel, Hannes
A1 - Meiller, M.
A1 - Müller, F.
A1 - Willbold, S.
A1 - Zang, J. W.
A1 - da Fonseca-Zang, W. A.
A1 - Adam, Christian
A1 - Klose, H.
A1 - Poorter, H.
A1 - Jablonowski, N. D.
A1 - Schrey, S. D.
T1 - Sugarcane bagasse ash as fertilizer for soybeans: Effects of added residues on ash composition, mineralogy, phosphorus extractability and plant availability
N2 - Sugarcane bagasse is commonly combusted to generate energy. Unfortunately, recycling strategies rarely consider the resulting ash as a potential fertilizer. To evaluate this recycling strategy for a sustainable circular economy, we characterized bagasse ash as a fertilizer and measured the effects of co-gasification and co-combustion of bagasse with either chicken manure or sewage sludge: on the phosphorus (P) mass fraction, P-extractability, and mineral P phases. Furthermore, we investigated the ashes as fertilizer for soybeans under greenhouse conditions. All methods in combination are reliable indicators helping to assess and predict P availability from ashes to soybeans. The fertilizer efficiency of pure bagasse ash increased with the ash amount supplied to the substrate. Nevertheless, it was not as effective as fertilization with triple-superphosphate and K2SO4, which we attributed to lower P availability. Co-gasification and co-combustion increased the P mass fraction in all bagasse-based ashes, but its extractability and availability to soybeans increased only when co-processed with chicken manure, because it enabled the formation of readily available Ca-alkali phosphates. Therefore, we recommend co-combusting biomass with alkali-rich residues to increase the availability of P from the ash to plants.
KW - Combustion and gasification
KW - Phosphate extractability and availability
KW - X-ray diffraction (XRD)
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567632
DO - https://doi.org/10.3389/fpls.2022.1041924
SN - 1664-462X
VL - 13
SP - 1
EP - 13
PB - Frontiers Media
CY - Lausanne
AN - OPUS4-56763
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Steckenmesser, D.
A1 - Vogel, Christian
A1 - Böhm, L.
A1 - Heyde, B.
A1 - Adam, Christian
T1 - Fate of heavy metals and polycyclic aromatic hydrocarbons (PAH) in sewage sludge carbonisates and ashes – A risk assessment to a thermochemical phosphorus-recycling process
N2 - In the near future, phosphorus (P) recycling will gain importance in terms of decreasing primary resources. Sewage sludge (SSL) is an adequate secondary P-resource for P-fertilizer production but it is also a sink for heavy metals and organic pollutants. The present study is an investigation on thermochemical P-recycling of SSL. Various temperatures and amendments were tested regarding their performance to remove heavy metals and polycyclic aromatic hydrocarbons (PAH) and simultaneous increase of the plant-availability of P. The investigations were carried out on two types of SSL originating from wastewater treatment plants with chemical P-precipitation and enhanced biological P-removal, respectively. The results show that thermochemical treatment with chlorine donors is suitable to remove the majority of heavy metals and that a combination of a gaseous chlorine donor (HCl) and sodium additives leads to both high heavy metal removal and high plant availability of P. Furthermore, plant experiments Show that almost all investigated thermochemical treatments can significantly reduce the bioavailability and plant uptake of heavy metals. Furthermore, PAHs are secondarily formed during low-temperature treatments (400–500 ° ), but can be significantly reduced by using sodium carbonate as an additive.
KW - Fertilzer
KW - Pollutant
KW - Phosphorus
PY - 2018
DO - https://doi.org/10.1016/j.wasman.2018.06.027
SN - 0956-053X
VL - 78
SP - 576
EP - 587
PB - Elsevier Ltd.
CY - Amsterdam
AN - OPUS4-45341
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kratz, S.
A1 - Adam, Christian
A1 - Vogel, Christian
T1 - Düngewirkung von P-Rezyklaten
N2 - Die agronomische Effizienz von Düngemitteln wird üblicherweise in Vegetationsversuchen geprüft. Diese erlauben die es, unterschiedliche Kulturpflanzen und deren Strategien der Nährstoffmobilisierung und -aneignung zu betrachten und verschiedene Substrattypen und deren Eigenschaften im Hinblick auf Nährstofffixierung und -freisetzung zu berücksichtigen. Solche Versuche, selbst wenn sie nicht im Feld, sondern nur im Gefäß durchgeführt werden, sind jedoch sowohl zeit- als auch kostenintensiv. In erster Näherung wird die Pflanzenverfügbarkeit insbesondere von Phosphor (P)-Düngemitteln daher in der Regel mit Hilfe standardisierter chemischer Extraktionsmethoden abgeschätzt, deren Durchführung in der deutschen ebenso wie in der europäischen Düngemittelverordnung normiert ist. Diese Methoden werden auch bei der staatlichen Düngemittelverkehrskontrolle genutzt, um zu überprüfen, ob die düngemittelrechtlichen Vorgaben eingehalten werden. Wie jüngere Arbeiten gezeigt haben, ist es jedoch schwierig, herkömmliche Standardextraktionsmethoden auf neue Dünger aus Recyclingmaterialien wie Klärschlamm zu übertragen. Korrelationen zwischen P-Aufnahme im Vegetationsversuch und chemischer Löslichkeit im Standardextrakt sind oft nur mäßig bis schwach oder überhaupt nicht signifikant. Die vorliegende Literaturübersicht gibt einen Überblick zum aktuellen Stand des Wissens über die chemische Löslichkeit von klärschlammbasierten P-Recyclingdüngern, deren Effizienz im Vegetationsversuch und statistische Relationen zwischen beiden Parametern. Anschließend werden alternative Methoden zur Abschätzung der P-Verfügbarkeit von Recyclingdüngern vorgestellt, die derzeit Gegenstand der wissenschaftlichen Diskussion sind.
KW - Abwasser
KW - Agronomische Effizienz
KW - Chemische Löslichkeit
KW - Düngemittel
KW - Extraktion
KW - Klärschlamm
KW - Pflanzenverfügbarkeit
KW - Pflanzenwurzel
KW - Phosphat
KW - Phosphor
KW - P-Recyclingdünger
KW - Relative agronomische Effizienz (RAE)
KW - Struvit
KW - Vegetationsversuche
PY - 2019
VL - 32
IS - 1
SP - 14
EP - 21
PB - Rhombos-Verlag
CY - Berlin
AN - OPUS4-47941
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Adam, Christian
T1 - Breites Leistungsspektrum - Für die Phosphorrückgewinnung aus Abwasser und Klärschlamm stehen aus technischer und ökonomischer Sicht verschiedene Verfahren zur Verfügung
N2 - Die P-Rückgewinnung aus Teilströmen mit erhöhten P-Gehalten kann direkt in den Kläranlagenbetrieb integriert werden und führt dort in vielen Fällen zu betrieblichen und ökonomischen Vorteilen. Sie ist in der Regel auf Bio-P-Kläranlagen beschränkt, da hier die anaerobe P-Rücklösung initiiert und genutzt werden kann. Durch die reine P-Rücklösung durch Schaffung anaerober Bedingungen ist allerdings das Potential der Rückgewinnung auf 5 bis 15 Prozent der Zulauffracht limitiert.
Die meisten Kläranlagen in Deutschland werden mit einer chemischen Phosphor-Fällung betrieben. Diese Anlagen können aus dem Klärschlamm Phosphat in ausreichend hoher Konzentration nur zurückgewinnen, indem zusätzlich anorganische Säuren wie Schwefelsäure zugeführt werden oder ein Aufschluss mit flüssigem Kohlendioxid stattfindet. Es wird angenommen, dass sich mit diesen Verfahren mehr als 50 Prozent der Zulauffracht einer Kläranlage zurückgewinnen lassen. Der Aufschluss von Klärschlamm mit Schwefelsäure geht aber mit vergleichsweise hohen Umweltwirkungen sowie mit höheren Kosten im Vergleich zu anderen Phosphor-Rückgewinnungsverfahren einher. Ein sehr hohes Potential der Rückgewinnung von Phosphor (P) ist bei allen Verfahren gegeben, die als Rohstoff die Asche aus der Monoverbrennung verwerten. Der Aufschluss mit anorganischen Säuren ermöglicht die sichere Phosphor-Rückgewinnung von mehr als 80% Prozent des Kläranlagenzulaufs. Die Verfahren sind zum Teil großtechnisch umgesetzt oder es befinden sich großtechnische Anlagen im Bau. Auch thermochemische Verfahren wurden entwickelt und deren Einsatzbereitschaft im großtechnischen Maßstab erfolgreich demonstriert. In dem nachfolgenden Beitrag werden unterschiedliche praxiserprobte Verfahren zur Phosphor-Rückgewinnung unter technischen und wirtschaftlichen Aspekten vorgestellt.
KW - Abwasserreinigung
KW - Bio-P-Kläranlage
KW - Elimination
KW - Fällmittel
KW - Kläranlage
KW - Klärschlamm
KW - Klärschlammasche
KW - Klärschlammverordnung
KW - Monoverbrennung
KW - Permeat
KW - Phosphat
KW - Phosphor
KW - Phosphorrückgewinnung
KW - Retentat
KW - Struvit
KW - Zentrat
PY - 2019
VL - 32
IS - 1
SP - 4
EP - 13
PB - Rhombos-Verlag
CY - Berlin
AN - OPUS4-47942
LA - deu
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Gentzmann, Marie
A1 - Schraut, Katharina
A1 - Vogel, Christian
A1 - Gäbler, H.-E.
A1 - Huthwelker, T.
A1 - Adam, Christian
T1 - Investigation of scandium in bauxite residues of different origin
N2 - This paper focuses on the scandium speciation in bauxite residues of different origin. Insights into mineralchemical similarities and differences of these materials will be presented and links to their natural geological background discussed. The presented research should provide fundamental knowledge for the future development of efficient and viable technologies for Sc-recovery from bauxite residues derived from different bauxites and accumulating at different localities. In total, five bauxite residues were investigated which originated from Greece, Germany, Hungary and Russia (North Ural & North Timan) using a combination of different analytical tools. Those included: laser ablation inductively coupled plasma mass spectrometry, X-ray absorption near Edge structure (XANES) spectroscopy, μ-Raman spectroscopy as well as scanning electron microscopy and electron microprobe analyses. X-ray fluorescence and inductively coupled plasma mass spectrometry were used to determine the overall chemical composition. The investigated samples were found to exhibit a relatively homogenous distribution of Sc between the larger mineral particles and the fine-grained matrix except for Al-phases like diaspore, boehmite and gibbsite. These phases were found to be particularly low in Sc. The only sample where Sc mass fractions in Al-phases exceeded 50 mg/kg was the Russian sample from North Ural. Fe-phases such as goethite, hematite and chamosite (for Russian samples) were more enriched in Sc than the Al-phases.
In fact, in Greek samples goethite showed a higher capacity to incorporate or adsorb Sc than hematite. Accessory minerals like zircon, rutile/anatase and ilmenite were found to incorporate higher mass fractions of Sc (>150 mg/kg), however, those minerals are only present in small amounts and do not represent major host phases for Sc. In Russian samples from North Ural an additional Ca–Mg rich phase was found to contain significant mass fractions of Sc (>500 mg/kg). μ-XANES spectroscopy was able to show that Sc in bauxite residue occurs adsorbed onto mineral surfaces as well as incorporated into the crystal lattice of certain Fe-phases. According to our observations the bauxite type, i.e. karstic or lateritic, the atmospheric conditions during bauxitization, i.e. oxidizing or reducing, and consequently the dominant Sc-bearing species in the primary Bauxite influence the occurrence of Sc in bauxite residues. In karstic bauxites, underlying carbonate rocks can work as a pH-barrier and stabilize Sc. This prevents the Sc from being mobilized and removed during bauxitization. Hence, karstic bauxites are more prone to show a Sc enrichment than lateritic bauxites. Reducing conditions during bauxitization support the incorporation of Sc into clay minerals such as chamosite, which can dissolve and reprecipitate during Bayer processing causing Sc to be redistributed and primarily adsorb onto mineral surfaces in the bauxite residue. Oxidizing conditions support the incorporation of Sc into the crystal lattice of Fe-oxides and hydroxides, which are not affected in the Bayer process. The genetic history of the bauxite is therefore the major influential factor for the Sc occurrence in bauxite residues.
KW - Sc recovery
KW - Scandium
KW - Bauxite Residue
KW - Red Mud
KW - XANES
PY - 2021
DO - https://doi.org/10.1016/j.apgeochem.2021.104898
SN - 0883-2927
VL - 126
SP - 104898
PB - Elsevier Ltd.
AN - OPUS4-52123
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kratz, S.
A1 - Vogel, Christian
A1 - Adam, Christian
T1 - Agronomic performance of P recycling fertilizers and methods to predict it: a review
N2 - Phosphorus (P) is an essential element for all life forms, and P-availability thus an important driver of a functioning agriculture. However, phosphate rock resources for P-fertilizer production are only available in a few countries. Therefore, P-recovery from waste materials has become of increasing interest during the last decade and has been investigated worldwide. In order to characterize potential novel P-fertilizers made from recycled materials, a large array of P-compound characterizations, chemical extractions and growth experiments were performed. This review bundles the work carried out in that field over the last years. Overall, P-fertilizers from recycled materials show a broad range of P-compounds with very different chemical structure and solubility. Growth experiments performed to assess their fertilizing effects display high variations for most of the products. While these experiments have demonstrated that some fertilizers made of recycled materials may reach P effects in the same order of magnitude as water-soluble phosphate rock-based fertilizers, an important limitation in their interpretation is the fact that they often vary considerably in their experimental design. The existing data show clearly that standardization of growth experiments is urgently needed to achieve comparable results. Standard chemical extractants used to assess the chemical solubility of P-fertilizers were found to be of limited reliability for predicting plant P uptake. Therefore, alternative methods such as sequential fractionation, or the extraction of incubated soil/fertilizer mixtures with standard soil extractants or with P sink methods should be tested more intensively in the future to provide alternative options to predict the P-availability of fertilizers from recycled materials.
KW - Recycling fertilizer
KW - Phosphorus
KW - Chemical extraction methods
KW - Agronomic performance
KW - Incubated soil/fertilizer mixtures
KW - P sink method
KW - Diffusive gradients in thin films (DGT)
PY - 2019
DO - https://doi.org/10.1007/s10705-019-10010-7
SN - 1385-1314
SN - 1573-0867
VL - 115
IS - 1
SP - 1
EP - 39
PB - Springer
AN - OPUS4-48713
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Steckenmesser, D.
A1 - Vogel, Christian
A1 - Steffens, D.
T1 - Medium-scale Plant Experiment of Sewage Sludge based Phosphorus Fertilizers from Large-scale Thermal Processing
N2 - Phosphorus (P) recycling from sewage sludge for agricultural needs has to meet requirements for agricultural implementation, such as short and long-term P-plant-availability under field conditions. Field experiments often bring no evaluable results, because agricultural soils got a high potential of P-supply even if they are classified as low in P-supply according to the CAL extraction method. The present study presents a possible way to investigate the P-plant-availability of P-recycling-fertilizers under field-like conditions. The plant experiments are firstly performed in small Mitscherlich pots in growth chambers and subsequently in containers with a high soil volume of 170 kg under greenhouse conditions, in which plants can grow until ripening. The tested P-recycling fertilizers were produced from sewage sludge in a large-scale thermal process. It was a two-step treatment process performed with a pyrolysis of sewage sludge at 550°C (SSC-550) and a subsequent thermochemical post-treatment at 950°C with Na2SO4 (SSA-Na) and HCl + Na2SO4 (SSA-HCl/Na) as additives. The results show, that the P-recycling-products from pyrolysis got an adequate long-term but a 65% lower short-term P-plant-availability compared to triple superphosphate. SSA-Na and SSA-HCl/Na show both a high short and longterm P-plant-availability comparable to triple-superphosphate. This can be explained by their highly plant-available P-compound CaNaPO4.
KW - Fertilzer
KW - Sewage sludge
KW - Plant Experiment
KW - Thermal treatment
PY - 2019
DO - https://doi.org/10.1080/00103624.2019.1667373
VL - 50
IS - 19
SP - 2469
EP - 2481
PB - Taylor & Francis
AN - OPUS4-49143
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Vogel, Christian
A1 - Hoffmann, Marie
A1 - Taube, Mareike
A1 - Krüger, O.
A1 - Baran, R.
A1 - Adam, Christian
T1 - Uranium and thorium species in phosphate rock and sewage sludge ash based phosphorus fertilizers
N2 - Phosphorus (P) is an essential element for all forms of life and is thus often applied as phosphate rock-based P-fertilizers in agriculture to enable continuous farming. However, these P-fertilizers contain also hazardous uranium (U) and thorium (Th), up to 660 and 220 mg/kg, respectively. On the contrary, novel P-fertilizers made from sewage sludge (ash) contain only low mass fractions of U and Th. In addition to the total amount of U and Th in P-fertilizers, their mobility and bioavailability is important, which depends to a large extent on their chemical state, especially oxidation state and chemical bonding. Thus, we analyzed their chemical state in various P-fertilizers by U and Th L3-edge HERFD-XANES spectroscopy. Phosphate rocks and sewage sludge-based P-fertilizers contain mainly U(IV) compounds which have only a low bioavailability. In contrast, acidic treatment of phosphate rock to produce super phosphates lead to an oxidation to U(VI) compounds (including formation of uranium phosphates) with a strongly increased bioavailability. On the contrary, all analyzed P-fertilizers contain Th in form of strongly insoluble phosphates and oxides with a low bioavailability. Additionally performed water extractions and Diffusive Gradients in Thin-films (DGT) experiments support these findings.
KW - Phosphorus fertilizer
KW - Sewage sludge
KW - X-ray absorption near-edge structure (XANES) spectroscopy
KW - Diffusive Gradients in Thin-films (DGT)
KW - Extraction
PY - 2020
DO - https://doi.org/10.1016/j.jhazmat.2019.121100
SN - 0304-3894
VL - 382
SP - 121100, 1
EP - 6
AN - OPUS4-48872
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Huber, F.
A1 - Herzel, Hannes
A1 - Adam, Christian
A1 - Mallow, O.
A1 - Blasenbauer, D.
A1 - Fellner, J.
T1 - Combined disc pelletisation and thermal treatment of MSWI fly ash
N2 - An environmentally friendly and cost efficient way for the management of municipal solid waste incineration (MSWI) fly ash represents its thermal co-treatment together with combustible waste. However, the safe introduction and storage of MSWI fly ash in the waste bunker is challenging and associated with severe problems (e.g. dust emissions, generation of undefined lumps and heat in case of moistened MSWI fly ash). Therefore, the aim of this study is to investigate the suitability of pelletisation as a pretreatment of MSWI fly ash. In particular, MSWI fly ash was characterised after sampling, pelletisation and thermal treatment and the transfer of constituents to secondary fly ash and flue gas was investigated. For this purpose, MSWI fly ash pellets with a water content of about 0.15 kg/kg and a diameter of about 8 mm have been produced by disc pelletiser and treated in an electrically heated pilot-scale rotary kiln at different temperatures, ranging from 450°C to 1050°C. The total contents of selected elements in the MSWI fly ash before and after thermal treatment and in the generated secondary fly ash have been analysed in order to understand the fate of each element. Furthermore, leachable contents of selected elements and total content of persistent organic pollutants of the thermally treated MSWI fly ash were determined. Due to the low total content of Hg (0.7 mg/kg) and the low leachate content of Pb (<0.36 mg/kg), even at the lowest treatment temperature of 450°C, thermally treated MSWI fly ash pellets can be classified as nonhazardous waste. However, temperatures of at least 650°C are necessary to decrease the toxic equivalency of PCDD/F and DL-PCB. The removal of toxic heavy metals like Cd and Pb is significantly improved at temperatures of 850°C, 950°C or even 1050°C. The observed metal removal led to relatively high contents of e.g. Cu (up to 11,000 mg/kg), Pb (up to 91,000 mg/kg) and Zn (up to 21,000 mg/kg) in the secondary fly ash. This metal enriched secondary fly ash might represent a potential raw material for metal recovery (e.g. via acidic leaching). Due to the high content of total dissolved solids observed in the leachate of thermally treated MSWI fly ash pellets, a wet extraction procedure is suggested to enable its safe disposal at non-hazardous waste landfills.
KW - MSWI fly ash
KW - Thermal treatment
PY - 2018
DO - https://doi.org/10.1016/j.wasman.2017.12.020
SN - 0956-053X
VL - 73
SP - 381
EP - 391
PB - Elsevier Ltd.
CY - Rotterdam
AN - OPUS4-44481
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Herzel, Hannes
A1 - Stemann, J.
A1 - Simon, Sebastian
A1 - Adam, Christian
T1 - Comparison of thermochemical treatment of sewage sludge ash with sodium sulphate in laboratory-scale and pilot-scale experiments
N2 - There is an ongoing debate on European scale concerning the criticality of phosphorus. In Switzerland and Germany, phosphorus recovery from phosphorus-rich waste streams will become obligatory. Sewage sludge ash is rich in phosphorus and may become an important secondary feedstock. Thermochemical treatment of sewage sludge ash with sodium sulphate under reducing conditions was shown to remove heavy metals from the solid product and produce the fully plant available crystalline phase CaNaPO4. Pilot-scale experiments in a rotary kiln were carried out at temperatures between 750 and 1000 °C and were compared to laboratory-scale experiments with crucibles. Process upscaling was successfully demonstrated but a series of differences were noticed: In comparison to laboratory-scale, solubility of phosphorus in samples from pilot-scale experiments was lower at all chosen treatment temperatures because of shorter retention time and incomplete decomposition of sodium sulphate. X-ray diffraction analysis revealed remaining phase fractions of whitlockite (Ca3-x(Mg,Fe)x(PO4)2) and sodium sulphate from the starting materials in products and thus indicated incomplete reaction. In contrast to the results of laboratory-scale experiments, the crystalline phase CaNaPO4 was clearly absent in the products from the rotary kiln but instead a Mg-bearing phase (Ca,Mg)NaPO4 was formed. Laboratory-scale experiments confirmed (Ca,Mg)NaPO4 is an intermediate phase between whitlockite and CaNaPO4. However, both crystalline phases are characterized by high plant availability. It was shown that heavy metal removal increased at higher temperatures whereas solubility and thus plant availability of phosphorus already reached its maxima at temperatures of 950 °C in pilot-scale and 875 °C in laboratory-scale experiments.
KW - Crystalline phase identification
KW - Heavy metal removal
KW - Phosphorus availability
KW - Process upscaling
KW - Recovery
KW - Rhenanite
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-524084
DO - https://doi.org/10.1007/s13762-021-03252-y
VL - 19
IS - 3
SP - 1997
EP - 2006
PB - Springer
AN - OPUS4-52408
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Stahl, E.
A1 - Meiller, M.
A1 - Danz, P.
A1 - Dombinov, V.
A1 - Herzel, Hannes
T1 - Recycling of nutrients from residues of thermo-chemical processing of sugarcane bagasse and straw - handling of produced fertilizers based on biomass ash
N2 - Jährlich entstehen in Brasilien ca. 2 bis 10 Millionen Tonnen Aschen aus der Verbrennung von Zuckerrohrbagasse. Die Aschen enthalten schwankende Zusammensetzungen an mineralischen Nährelementen und könnten daher zu Düngezwecken verwendet werden.
Allerdings ist (i) die Nährstoffverfügbarkeit gering, (ii), die entsprechende Nährstoffzusammensetzung nicht optimal für die Nutzung der Aschen als Düngemittel für die Hauptanbaukulturen in Brasilien und (iii) weisen die Aschen aufgrund häufig schlechter Verbrennungsqualitäten hohe organische Kohlenstoffgehalte auf. Im Rahmen des Forschungsprojekts ASHES („Rückführung von Nährstoffen aus Aschen von thermochemischen Prozessen mit Bagasse bzw. Zuckerrohrstroh“), arbeiten 7 deutsche und 4 brasilianische Partner an der Optimierung der thermochemischen Verwertung von Rückständen aus der Zuckerproduktion in Brasilien, inklusive der Formulierung von optimierten Düngemischungen auf Basis der generierten Aschen. In dieser Veröffentlichung wird die Verarbeitung dieser optimierten Mischungen zu Pellets und Granulaten unter Verwendung verfügbarer regionaler Reststoffe wie Filterkuchen (Vinasse-Presskuchen) sowie Hühnertrockenkot beschrieben. Zur Untersuchung der Handlingeigenschaften wurden die produzierten Pellets und Granulate hinsichtlich ihrer mechanischen Stabilität und des Wasseraufnahmevermögens untersucht. Dafür wurden geeignete Prüfverfahren angepasst und entsprechende Versuche durchgeführt.
KW - Bagasse
KW - Nährstoffe
KW - Mechanische Stabilität
KW - Granulat
PY - 2018
SN - 1435-3199
IS - 10
SP - 56
EP - 59
PB - VGB PowerTech e.V.
CY - Essen
AN - OPUS4-47555
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -