TY - CONF A1 - Trappe, Volker A1 - Kalinka, Gerhard A1 - Loose, Florian T1 - Carbon fibre composites exemplarily research at BAM N2 - Lightweighting as a cross-cutting technology contributes significantly to achieve the European Green Deal goals. Based on, but not limited to, advanced materials and production technologies, the demand for natural resources and CO2 emmissions are reduced by lightweighting during production, as well as use phase. Therefore, lightweighting is a crucial transformation technology assisting in decoupling economic growth from resource consumption. In this manner, lightweighting contributes significantly as a key technology of relevance for many industrial sectors such as energy, mobility, and infrastructure, towards resource efficiency, climate action and economic strength, as well as a resilient Europe. To strengthen international partnerships, addressing global issues of today at the edge of science with high performance lightweight material based on carbon fibers, an overview about the BAM expertise in carbon fiber reinforced materials is given. T2 - Meeting KCarbon CY - Berlin, Germany DA - 15.06.2023 KW - Lightweighting KW - Carbon Fibers KW - Recycling KW - Push-out Test KW - multi scale testing PY - 2023 AN - OPUS4-58094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Advanced lightweight applications – recycling versus reliability and fossil energy footprint N2 - Advanced light weight applications like aircrafts and wind turbine blades are made of fibre reinforced plastics (FRP) with continuous fibre reinforcement and must withstand a high thermo-mechanical cyclic loading. The quality of the fibre matrix interface has a high impact on the fatigue life and was continuously improved over the years since the 50th. The fatigue life of glass fibre reinforced plastics (GFRP) used in aircraft industry is 10 to 100 times higher compared to glass fibre non crimp fabrics used for wind turbine blades. To assure a constant and reliable high quality and strength of reinforcement fibres, synthetic fibre production is state of the art (CF, GF). There is a need for recycling GFRP and CFRP waste due to the upcoming use. Pyrolysis and solvolysis are more expensive than the mechanical route however enable a more sustainable recycling. Natural fibres and recycled synthetic fibres have a high scatter in quality and strength. Hence it is a challenge to optimize the production / recycling processes to get a reliable quality for any demanding (second life) application. Chemical routes for using renewables resources and recycling, is going to be a good approach especially for polymer-matrix systems to get 100% quality (back) compared to the state of the art. Finally, a proper design, life-time extension and repair is preferable to recycling to keep the carbon footprint as low as possible. T2 - 27. INTERNATIONALES DRESDNER LEICHTBAUSYMPOSIUM CY - Dresden, Germany DA - 13.06.2024 KW - Polymer Matrix Composites KW - Carbon Fibre KW - Recycling KW - Circular Economy PY - 2024 UR - https://leichtbausymposium.de/deu/ AN - OPUS4-60683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Taube, Mareike Carolin A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Feldmann, Ines A1 - Ostermann, Markus A1 - Reuter, M. A1 - Stelter, M. T1 - Tantalrecycling aus pyrometallurgischen Rückständen N2 - Gegenstand dieser Arbeit ist die Untersuchung eines bestehenden pyrometallurgischen Prozesses zur Rückgewinnung von Tantal und Niob aus metallurgischen Reststoffen mit vorwiegend niedriger Wertstoffkonzentration. Zur näheren Erforschung der im vorliegenden Stoffsystem ablaufenden Reduktionsprozesse wurden in einem Elektrolichtbogenofen Schmelzversuche im Pilotmaßstab durchgeführt. Als Reduktionsmittel diente Koks, welcher mithilfe einer Argon-gespülten Eisenlanze in die flüssige mineralische Schmelze eingebracht wurde. Während der Reduktionsbehandlung werden Refraktärmetalle wie Tantal und Niob in ihre Carbide überführt und anschließend in der erschmolzenen eisenbasierten Metallphase am Boden des Reaktors angereichert. Neben Tantal und Niob gelangt auch ein Teil des im Einsatzmaterial enthaltenen Titans als unerwünschtes Begleitelement in die Metallphase. Sein Großteil verbleibt jedoch als Oxid in der Schlacke und wird dort hauptsächlich im Mineral Perowskit (CaTiO3) gebunden. Die erstarrten Schlackeproben wurden mit verschiedenen Methoden wie Röntgenfluoreszensanalyse, Röntgenbeugung und Rasterelektronenmikroskopie mit gekoppelter energiedispersiver Röntgenanalyse untersucht, um die Bildung tantalhaltiger Mineralphasen zu verschiedenen Stadien des Reduktionsprozesses zu verfolgen. Die hier gewonnenen Erkenntnisse zeigen, dass weniger die durch das Einblasen von Koks verursachte Reduktionsreaktion, sondern das Absinken der tantalreichen Eisentröpfchen in der flüssigen mineralischen Schmelze, gefolgt von ihrer Anreicherung in die Metallphase, für die Kinetik ausschlaggebend ist. N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Melting experiments were carried out in a pilot-scale electric arc furnace to study the material system during the reduction process caused by blowing coke into the liquid mineral melt. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are converted into their carbides and enriched in the molten iron-based metal phase. Titanium is also enriched in the metal phase as an unwanted accompanying element, but most of it remains in oxidic form in the slag and is mainly bound in the mineral perovskite. Cooled down slag samples were analysed using XRF, XRD, SEM and EDX to investigate the formation of mineral phases rich in tantalum during various stages of the reduction process. The results show that the settling of the tantalum-rich iron droplets in the molten slag into the metal phase May play a greater role for the kinetics than the actual reduction reaction caused by blowing in coke. KW - Tantal KW - Recycling KW - Reduktionsprozess KW - Perowskit KW - Elektrolichtbogenofen PY - 2020 SN - 1613-2394 VL - 73 IS - 4 SP - 196 EP - 205 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-51064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. ED - Reiser, B. T1 - Recycling von metallurgischen Rückständen - Schmelzversuche zeigen, wie die Tantalrückgewinnung aus Zinnschlacken und weiteren Reststoffen optimiert werden kann N2 - Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment. In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided. Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases. N2 - Da das Recycling von tantalhaltigen Post-Consumer-Abfällen praktisch nicht existiert, stellen metallurgische Reststoffe eine äußerst wichtige Rohstoffquelle für das Tantalrecycling dar. Die meisten Zinnerze enthalten von Natur aus erhebliche Mengen an Refraktärmetallen. Diese Elemente werden in den Schlacken der pyrometallurgischen Primärzinngewinnung angereichert. Aufgrund ihrer vergleichsweise hohen Wertstoffkonzentration und ihrer Funktion als zusätzlicher Schlackenbildner stellen diese Schlacken einen wertvollen Rohstoff für die Verhüttung tantalhaltiger Reststoffe dar. In der vorliegenden Arbeit wird ein existierendes Verfahren zur Tantalrückgewinnung diskutiert, dem hauptsächlich pyrometallurgische Rückstände geringer Wertstoffkonzentration als Einsatzstoff dienen. Mit Hilfe des Verfahrens sollte dasoxidisch vorliegende Tantal vollständig reduziert und in der Metallphase angereichert werden. Weiterhin sollte vermieden werden, dass unerwünschte Elemente wie Titan in die Metallphase überführt werden. Ziel der Untersuchung war es, die ablaufenden Reduktionsprozesse besser zu verstehen, um so Ansätze für die Prozessoptimierung identifizieren zu können. KW - Lichtbogenofen KW - Pyrometallurgie KW - Recycling KW - Tantal KW - Zinnschlacke PY - 2020 SN - 0934-3482 VL - 33 SP - 10 EP - 17 PB - Rhombos-Verlag CY - Berlin AN - OPUS4-50656 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz T1 - Solution-driven processing of calcium sulfate: the mechanism of the reversible transformation of gypsum to bassanite in brines N2 - Calcium sulfate hemihydrate (CaSO4ᐧ0.5H2O), also known as bassanite, has been used as a precursor to produce gypsum (dihydrate, CaSO4ᐧ2H2O) for various construction and decorative purposes since prehistoric times. The main route to obtain hemihydrate is a thermal treatment of gypsum at temperatures typically between 150 °C and 200 °C to remove some of the structural water. In this contribution, we introduce (Fig. 1) a more efficient and sustainable method (T < 100 °C) that enables the direct, rapid, and reversibly conversion of gypsum to bassanite using reusable high salinity aqueous solutions (brines with c[NaCl] > 4 M). The optimum conditions for the efficientproduction of bassanite in a short time (< 5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the typical behaviour of the bassanite phase in low salt environments. Traditionally, hemihydrate is obtained through a solid state thermal treatment because bassanite is considered to be metastable with respect to gypsum and anhydrite in aqueous solutions, and therefore gypsum-to-bassanite conversion should not occur in water. Its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures is inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline structure for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios. T2 - Granada Münster Discussion Meeting GMDM 10 CY - Münster, Germany DA - 29.11.2023 KW - Gypsum KW - Bassanite KW - Calcium sulfate KW - Recycling KW - Scattering PY - 2024 AN - OPUS4-59162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Kalbe, Ute T1 - Measurement of the Environmental Impact of Materials N2 - This Special Issue, ‘Measurement of the Environmental Impact of Materials’, is focused on the impact that materials have on the environmental compartments of soil, water and air. Leaching and emission processes, including underlying mechanisms, are a recurring topic in most published articles in the present Special Issue. Contributions have come from three continents and numerous countries (USA, Germany, France, Latvia, Poland, Russia, Japan, Korea and Thailand) indicating the global dimension of the subject. KW - Leaching KW - Recycling KW - Nano-materials PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-545099 DO - https://doi.org/10.3390/ma15062208 SN - 1996-1944 VL - 15 IS - 6 SP - 1 EP - 3 PB - MDPI CY - Basel AN - OPUS4-54509 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlögel, Kai A1 - Loose, Florian T1 - Enhancing the Sustainability of Carbon Fibre Reinforced Polymers (CFRP Strategies for Effective Feedstock Recycling as Reducing Agents in Pyrometallurgy N2 - Despite its contribution to tackling climate change by lightweight design, growing CFRP production also results in a global waste generation of 62 kt/a. Accordingly, the energy-intensive production process of carbon fibers (CF) necessitates sustainable recycling solutions. Herein we will give an overview of current recycling processes, discuss their limitations and present a novel approach for safe treatment of CF unsuitable for material recovery . Our project CF Pyro examines feedstock recycling in pyrometallurgical processes, focusing on reactivity of CF, process stability and prevention of hazardous WHO fiber release. Besides fundamental experimental breakthroughs, their broader impact on circular economy will be presented. T2 - CU Online Forum „Composites and Sustainability“ CY - Online meeting DA - 29.06.2021 KW - Carbon Fibers KW - Recycling KW - Electric Arc Furnace KW - CFRP KW - Pyrometallurgy KW - Steelmaking PY - 2021 AN - OPUS4-52920 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piehl, Patrick T1 - Thermochemische Aufarbeitung von Stahlwerksstäuben und -schlämmen zur Zink- und Eisenrückgewinnung N2 - Stahlwerksstäube und -schlämme enthalten in der Regel Schwermetalle wie Zink, Blei und Cadmium, die ein direktes Recycling verhindern und diese Stoffe potenziell umweltgefährdend machen. Um diese Schwermetalle aus den Materialien zu entfernen, werden drei thermochemische Verfahren zur Aufarbeitung von Gichtgasschlamm, Elektroofenstaub und ähnlichen Stahlwerksstäuben vorgestellt. Zum einen kann die Mischung von Elektroofenstaub mit chloridhaltigen Lösungen, wie sie z. B. in der Titandioxidproduktion anfallen, gemischt werden, um bei der thermischen Behandlung Schwermetallchloride zu effektiv verdampfen. Weiterhin kann der im Gichtgasschlamm enthaltene Kohlenstoff genutzt werden, um in Mischungen aus Gichtgasschlamm und Elektroofenstaub bei der thermischen Behandlung als Reduktionsmittel zu wirken. Dieses Verfahren führt zur Rückgewinnung von Zink und metallischem Eisen und wird im Technikums- und Pilotmaßstab erprobt. Abschließend wird die Nutzung von Wasserstoff als Reduktionsmittel für Elektroofenstaub vorgestellt. Hierbei lässt sich der Reststoff potenziell klimaneutral in Eisenschwamm umwandeln, wobei die chemischen Grundlagen anhand von DTA-Experimenten und thermodynamischen Simulationen ergründet werden. T2 - Berliner Konferenz Metallkreisläufe CY - Berlin, Germany DA - 13.04.2024 KW - Elektroofenstaub KW - Gichtgasschlamm KW - Recycling KW - Ressourcenrückgewinnung KW - Zink PY - 2024 AN - OPUS4-59726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piehl, Patrick T1 - Thermochemical Treatment of Steel Work Dusts and Sludges for the Recovery of Zinc and Iron N2 - Steel work dusts and sludges usually contain severe amounts of zinc, lead, cadmium, and other heavy metals, which hinder direct recycling and make these materials potentially hazardous for the environment. To tackle this issue, here, two thermochemical treatment methods for the reductive workup of blast furnace sludge, electric arc furnace dust, and comparable steelwork dusts are presented. In the first method, carbon contained blast furnace sludge is employed as reducing agent for the material’s metal oxides. By this, heavy metals get evaporated and a metallic iron containing residue that may be reused in electric arc furnace steelmaking is formed. Additionally, the use of hydrogen for reducing iron and heavy metal oxides in steelwork dusts is presented. Here, high evaporation rates of heavy metals can be reached, and sponge iron is formed. Investigations using thermogravimetry and equilibrium simulations provide insides into the reactions taking place. For both processes an upscaling to pilot scale is ongoing. T2 - EUROSLAG 2024 CY - Bilbao, Spain DA - 23.10.2024 KW - Electric arc furnace dust KW - Blast furnace sludge KW - Recycling KW - Ressource recovery KW - Zinc PY - 2024 AN - OPUS4-61499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piehl, Patrick T1 - Thermochemical treatment of steel work dusts and sludges for the recovery of zinc and iron N2 - During iron and steel production, several by-products such as slags, dusts, and sludges are generated in addition to pig iron and steel as primary products. Especially for filter dusts and sludges containing zinc and lead from gas purification, there are still considerable recycling problems. However, the high heavy metal contents make landfilling of these dusts and sludges cost-intensive and ecologically problematic. In addition, the relatively high zinc and iron loads represent a valuable resource, which can make reprocessing of the material with recovery of the zinc and iron loads as secondary raw materials ecologically as well as economically attractive. Nevertheless, established recycling methods like the Waelz process fall short in regaining more than one valuable metal from the dusts and operate only under narrow ranges of material compositions, which makes it problematic to adapt these processes to new dust compositions as are to be formed in future steel work operations. To tackle these problems, the German Federal Institute for Materials Research and Testing (BAM) and Ferro Duo GmbH investigate innovative recycling methods for steelwork dusts and sludges in a joint project. This mainly focusses on regaining valuable metals such as iron as well as zinc from blast furnace sludge (BFS) and electric arc furnace dust (EAFD) by thermochemical treatment. Therefore, mixtures of these materials are heated under inert atmosphere employing the carbon present in BFS as internal reducing agent. During the process, metallic iron is formed in the solid reaction product while zinc and other volatile heavy metals are evaporated. This paves the way for the generation of zinc as well as sponge iron as two separate products valuable for metallurgical processes. The process basically consists of heating a mixture of BFS and EAFD to temperatures between 700 and 1100 °C under inert (e.g., nitrogen) or reducing (e.g., CO) gas flow. When a suitable mixing ratio is applied, the carbon present in the BFS can be effectively used as reducing agent for iron and zinc present in both starting materials generating a solid residue with high metallic iron and low carbon content as well as a gas stream laden with zinc and other volatile heavy metals, that can be regained by off-gas treatment. The project aims at testing this concept as a continuous process in a pilot plant established by Ferro Duo GmbH with BAM supplying comprehensive scientific support by lab- and small scale-experiments. Additionally, considering the necessity to mitigate CO2 emissions and the resulting shift in compositions of steel work dusts and sludges, our research also investigates replacement of carbon present in the sludges by hydrogen as potentially carbon-neutral reducing agent. Here, the use of non-explosive forming gas as reducing agent for EAFD shows potential to give a product high in metallic iron while zinc and other heavy metals are effectively evaporated from the solid material making it possible to regain them from the exhaust gas stream. T2 - 11th European Slag Conference CY - Cologne, Germany DA - 04.10.2022 KW - Elektroofenstaub KW - Gichtgasschlamm KW - Recycling KW - Ressourcenrückgewinnung KW - Zink PY - 2022 AN - OPUS4-55950 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -