TY - JOUR A1 - Müller, Werner W. A1 - Wöhlecke, Andreas T1 - Zero leakage? Landfill liner and capping systems in Germany N2 - An approach to achieve 'zero leakage' is discussed with respect to experience in Germany, where strict regulations for landfill lining and capping Systems have been developed and issued because of large environmental Problems related to landfills that accumulated in the 1970s and 1980s. Using a thick, high-quality high-density Polyethylene (HDPE) geomembrane (GM) that is installed free of residual waves and wrinkles in intimate contact with a compacted clay liner or geosynthetic clay liner of very low permeability, by a qualified, experienced, well-equipped and properly third-party-controlled installer, and which is protected by heavy protection layers designed with respect to the long-term performance of the GM may result in a liner or capping system of practically no leakage. This is demonstrated by analysing results of measurements obtained from permanently installed leak-detection Systems in combination with HDPE GMs. The survey was based on 32 German landfills with 1.276.500 m² of installed GMs. KW - Geomembranes KW - Landfill KW - Landfill lining PY - 2019 DO - https://doi.org/10.1680/jenge.16.00031 SN - 2051-803X VL - 6 IS - 3 SP - 1600031, 162 EP - 170 PB - ICE AN - OPUS4-48626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Smol, M. A1 - Adam, Christian T1 - Towards circular economy for phosphorus in Poland N2 - In the transition to the Circular Economy (CE) model, where the added value of products is kept as long as possible and waste is eliminated, the sustainable management of raw materials plays a key role. In above CE model, especial attention is paid to CRMs which are economically and strategically important for the European economy, but have a high-risk associated with their supply. One of the most important element which can not be replaced and is an essential element for human nutrition, yet limited resource is phosphorus (P). An importance of issues related to sustainable P management results from EU legislation, which indicated P as a Critical Raw Material (CRM). The sustainable management of P-resources is especially important for the Baltic region. A consequence of waterborne loads passing into the sea, mainly as wastewater with a high P content is the eutrophication of the Baltic Sea environment. Due to the largest inputs of P (37%) into the Baltic Sea originate from Poland, the development of sustainable solutions aimed at more rational P management for this country is externally important. T2 - International Phosphorus Workshop 9 CY - Zurich, Switzerland DA - 08.07.2019 KW - Phosphorus recovery KW - Circular economy PY - 2019 AN - OPUS4-48614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Del Mastro, G. A1 - Hammerstaedt, J. A1 - Mocella, V. A1 - Rabin, Ira T1 - XRF ink analysis of selected fragments from the Herculaneum collection N2 - Hundreds of papyrus rolls, carbonized during the 79CE eruption of Mount Vesuvius, were discovered in 1754 at Herculaneum. Sophisticated mechanical methods for unrolling the best-preserved scrolls have been applied, with varying success. However, such processes have been abandoned, to prevent risk from irremediable damage or loss and to preserve the integrity of the extremely fragile rolls. Following the development of X-ray based non-invasive techniques, attempts to virtually unroll the scrolls were made. The most common ink in Antiquity was carbon-based, and the main element of carbonized papyrus is carbon, making these investigations difficult. However, some attempts with synchrotron X-ray phase-contrast tomography (XPCT) were successful. Recently, the identification of antique inks containing metals raised hope that if some of the inks contain metal the rolls can be virtually unrolled using conventional CT- technique. We are presenting here the first results of a preliminary analysis, which aimed at identifying scrolls whose ink contains metals. T2 - Konferenz: 29th International Congress of Papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Herculaneum KW - Papyrus KW - Tomography KW - XRF KW - Ink PY - 2019 AN - OPUS4-48615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Smol, M. A1 - Adam, Christian T1 - Possibility of recovering phosphorus from sewage sludge ash (SSA) in Poland N2 - Due to the vital importance of phosphorus (P) and its increasing scarcity as a natural resource, phosphorus recovery has recently gained significant scientific and technical interest. An interesting sources of phosphorus are sewage sludge (SS) and sewage sludge ash (SSA) due to the major part of the phosphate from P rich wastewater is transferred to the sludge (approx. 90%). Despite the fact that the raw materials base is large (PURE report indicates that in 2020 the amount of sewage sludge generated in Poland will reach 180% of the dry matter of sewage sludge produced in 2010), at present recycling of phosphorus is not a commonly used practice in Poland. T2 - International Phosphorus Workshop 9 CY - Zurich, Switzerland DA - 08.07.2019 KW - Sewage sludge ash KW - Phosphorus recovery PY - 2019 AN - OPUS4-48616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Adam, Christian A1 - Stolle, Dirk A1 - Spanka, M. A1 - Auer, G. T1 - Thermochemical treatment of waste products from iron and steel production N2 - Blast furnace (BF) sludge and electric arc furnace (EAF) dust are typical wastes that incur from iron and steel production. In addition to iron, calcium, carbon, and silicon they usually contain high concentrations of heavy metals such as zinc, lead, and cadmium that are potentially hazardous to the environment, rendering disposal in landfills ecologically problematic and costly. Consequently, pyrometallurgical, hydrometallurgical, and hybrid methods for selective elimination of non-ferrous heavy metals from BF sludge and EAF dust have been conceived, of which only the carbothermic reduction route taken in the so-called Waelz rotary kiln process has been proven to be economically successful. However, this process has several drawbacks regarding efficiency of heavy-metal removal and recovery of iron, and it does not allow processing of BF sludge. In this study, we investigated the efficiency and feasibility of selective chlorination and evaporation of non-ferrous heavy metals, particularly zinc and lead, in both BF sludge and EAF dust as an alternative, thermochemical processing route. To this end, hydrochloric acid and iron(II) chloride solution have been used as chlorinating agents, and the process of heavy-metal chlorination and evaporation has been investigated under inert operating conditions, at variable chlorine concentrations, and at temperatures between 500 and 1200 °C. High zinc and lead removal efficiencies of > 99.5 % were achieved with both chlorinating agents, but iron(II) chloride turned out to be overall more efficient for removal of zinc and lead from BF sludge and EAF dust. Interestingly, and in contrast to previous studies, the iron was completely retained in the processed solid residue, therefore rendering the processed residues virtually zinc- and lead-free raw materials that may either be used internally (e.g., feeding processed BF sludge and EAF dust back into the respective furnaces) or externally (e.g., for cement production). T2 - European Metallurgical Conference 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Blast furnace sludge KW - Electric arc furnace dust KW - Recycling KW - Selective chlorination KW - Zinc PY - 2019 SN - 978-3-940276-89-6 VL - 3 SP - 1267 EP - 1282 PB - GDMB CY - Clausthal-Zellerfeld AN - OPUS4-48362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Influence of carbon feeding on a pyrometallurgical tantalum and niobium recycling process and the formation of carbides N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage. T2 - Euopean Metallurgical Conference (EMC) 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Pyrometallurgy KW - Tantalum KW - Carbide formation KW - Reduction process KW - Carbon feeding PY - 2019 SN - 978-3-940276-87-2 VL - 1 SP - 371 EP - 386 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-48363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Adam, Christian A1 - Stolle, Dirk A1 - Spanka, M. A1 - Auer, G. T1 - Thermochemical treatment of waste products from iron and steel production N2 - This presentation summarizes the development of a novel thermochemical process for recycling of zinc and lead-bearing wastes (blast furnace sludge and electric arc furnace dust) that accumulate during iron and steel production. T2 - European Metallurgical Conference 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Blast furnace sludge KW - Electric arc furnace dust KW - Recycling KW - Selective chlorination KW - Zinc PY - 2019 AN - OPUS4-48364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steger, Simon A1 - Oesterle, D. A1 - Bretz, S. A1 - Frenzel, L. A1 - Stege, H. A1 - Winkelmeyer, I. A1 - Hahn, Oliver A1 - Geiger, G. T1 - Kandinsky’s fragile art: a multidisciplinary investigation of four early reverse glass paintings (1911–1914) by Wassily Kandinsky N2 - This work highlights the rediscovery of the technique of reverse glass painting by the artists of the “Blaue Reiter” collective in the early 20th-century and focusses particularly on the role of Wassily Kandinsky (1866–1944). Kandinsky created more than 70 reverse paintings on glass and showed several of them in exhibitions together with paintings on canvas and cardboard, implying a coequal importance of these techniques. Four of his early (1911–1914) reverse glass paintings (Auferstehung, Allerheiligen II, Rudern, Apokalyptischer Reiter II) were selected for investigation and their iconography, painting techniques and painting materials were examined. Two paintings were executed on so-called cathedral glass, revealing a “hammered surface”, whereas Kandinsky used a corrugated glass panel for Rudern. A multi-analytical, non-invasive approach [X-ray fluorescence (XRF), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), VIS spectroscopy (VIS), Raman spectroscopy] was taken to identify the pigments and classify the binding media. The results reveal a broad palette of materials. Several pigments like lead white, zinc white, Strontium yellow, Prussian blue, viridian, cadmium yellow, ultramarine blue, cinnabar and carbon black were found in most of the four paintings. The use of the rare synthetic organic pigments PR60 and PB52 is discussed. In two works of art, cadmium carbonate is associated with cadmium yellow. The identification of aluminium foil along with tin foils in Rudern indicates an early use of this material for reverse glass paintings. KW - Reverse glass painting KW - Non-invasive analysis KW - Raman spectroscopy KW - DRIFTS PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-480075 DO - https://doi.org/10.1186/s40494-019-0268-8 VL - 7 IS - 27 SP - 1 EP - 17 PB - Springer AN - OPUS4-48007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steger, Simon A1 - Stege, H. A1 - Bretz, S. A1 - Hahn, Oliver T1 - A complementary spectroscopic approach for the non-invasive in-situ identification of synthetic organic pigments in modern reverse paintings on glass (1913–1946) N2 - This work addresses the identification of synthetic organic pigments (SOP) in eight modern reverse paintings on glass (1913–1946) by means of an in-situ multi-analytical approach. We combined the complementary properties of mobile Raman spectroscopy and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) to overcome the main disadvantages of each method: extensive band overlapping in DRIFT spectra and fluorescence problems in Raman spectra. A collection of DRIFTS reference spectra enables a precise pigment identification by DRIFTS and establishes this method as a serious non-destructive alternative for the identification of SOP. The group of β-naphthol pigments yielded valuable results for both methods, whereas synthetic alizarin (PR83) was preferentially detected by DRIFTS. Finally, uncommon triaryl carbonium pigments and two azo group-based yellows were identified in the paintings by means of Raman spectroscopy. KW - Synthetic organic pigments KW - DRIFTS KW - Raman spectroscopy KW - Reverse glass painting PY - 2019 DO - https://doi.org/10.1016/j.culher.2019.01.011 SN - 1296-2074 SN - 1778-3674 VL - 38 SP - 20 EP - 28 PB - Elsevier Masson SAS. AN - OPUS4-48008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Stege, H A1 - Bretz, S. A1 - Hahn, Oliver T1 - A complementary spectroscopic approach for the non invasive in situ identification of synthetic organic pigments in modern reverse paintings on glass N2 - This work addresses the identification of synthetic organic pigments (SOP) in ten modern reverse paintings on glass (1912-1946) by means of an in-situ multi-analytical approach. The combination of the complimentary properties of mobile Raman spectroscopy and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) enabled the detection of sixteen SOP even in complex mixtures with inorganic compounds and binders. For the β-naphthol pigments, both Raman and DRIFTS yield appropriate results. DRIFTS was the preferred method for the detection of synthetic alizarin (PR83). Its diagnostic band pattern even allows its detection in complex mixtures with mineral pigments, binders and fillers. Raman spectroscopy yielded distinctive spectra for the triaryl carbonium pigments (PG1, PV2, PR81) and the two-yellow azo SOP (PY3, PY12), whereas DRIFT spectra were affected by extensive band overlapping. This may also occur in Raman spectra, but in less problematic amounts. Fluorescence is the major problem with Raman and it significantly hampers the SOP spectra even with the 785 nm laser. On the one hand the big spot size of DRIFTS (10 mm) limits the technique to rather large sampling areas, whereas the use of a 50× objective for in-situ Raman measurements permits a focus on small spots and aggregated SOP flakes. Moreover, “environmental” factors like temperature changes, artificial light, limited space and vibrations when people pass by need to be considered for in-situ measurements in museums. Finally, the results show the experimental use of SOP in modern reverse glass paintings. Among several rare SOP (e.g. PB52, PR81), two of them (PG1, PV2) have never been reported before in any artwork. T2 - Technart2019 CY - Bruges, Belgium DA - 07.05.2019 KW - Synthetic organic pigments KW - Reverse glass painting KW - DRIFTS KW - Raman spectroscopy PY - 2019 AN - OPUS4-48009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Oesterle, D. A1 - Mayer, R. A1 - Hahn, Oliver A1 - Bretz, S. A1 - Geiger, G. T1 - First insights into Chinese reverse glass paintings gained by non invasive spectroscopic analysis N2 - A non-invasive methodological approach (X-ray fluorescence (XRF), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), Raman spectroscopy) has been carried out to identify the pigments and classify the binding media in two Chinese reverse glass paintings (The Archer, Yingying and Hongniang) from the late 19th and early 20th centuries. The results reveal a combined use of traditional Chinese and imported European materials. Several pigments like cinnabar, lead white, orpiment, carbon black and copper-arsenic green (probably emerald green) were found in both paintings; red lead, artificial ultramarine blue, Prussian blue and ochre appear in at least one of the paintings. The presence of portlandite (Ca(OH)2) along calcite (CaCO3) in the fine-grained, white backing layer of Yingying and Hongniang indicates the presence of limewash. In Chinese tradition, limewash was produced from clamshells, and was then sold as clamshell white. In contrast to the Japanese pigment, Chinese clamshell white was made of finely grounded shells, which were heated over a low fire. The residue (CaO) forms portlandite (Ca(OH)2) when water is continuously added. This water-rich mixture is applied on the painting. Portlandite reacts with atmospheric CO2 during drying and forms fine-grained calcite (CaCO3) [1,2]. The identification of emerald green (The Archer) suggests an earliest manufacturing date in the 1830s [3] and promotes the sinological dating of the painting. Drying oil was classified as a binding media in most areas of both paintings. However, the orange background of The Archer yielded prominent bands of both proteinaceous and fatty binder. T2 - Technart2019 CY - Bruges, Belgium DA - 07.05.2019 KW - Reverse glass painting KW - Raman spectroscopy KW - Non-invasive analysis PY - 2019 AN - OPUS4-48010 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Seneschal-Merz, Karine A1 - Feldmann, Ines A1 - Bücker, Michael A1 - Oleszczuk, S. T1 - EDX-Analysis on medieval glasses and innovative protection of stained glass panels N2 - The church of Koszewko (Poland) is a brick building edified in the 15th century built on cobblestone foundations. There are five windows in the sanctuary. Three of them enclose heraldic panels from the Küssow’s family from the 15th century which are surrounded with Goethe glass from the 18th century to complete the windows. The colored heraldic panels are strongly damaged and corroded with massive paint layer losses, glass- and leadbreakages. Those medieval glass fragments have been shortly discovered and are of particular interest for Poland since only few medieval glazing have been conserved. The damages as well as the glass compositions have been investigated with ESEM/EDX. Two categories of medieval glass compositions have been identified. The blue glass is particularly sensible to corrosion because of his high content in K2O. The colorless and the red glass samples belong to a stable glass type. Due to the thickness of the gel layer, it is easy to see that the degradation is strongly proceeded. The protection of those medieval stained-glass panels is absolute necessary. The medieval panels have been restored and surrounded from a copper frame. Then they have been fixed on the wood frame in the church. The exterior glazing has been closed with a panel of Goethe glass. The gap between the Goethe- and the medieval glass is about 3 cm. The Goethe glass panel has been stabilized with a film based on polyester to protect the medieval glasses against any damages. In this way, a low cost protective glazing has been installed for a long-term conservation of each medieval stained-glass panels. The climate measurements over the period of one year on the restored windows are in process. The temperature and the relative humidity are recorded in the church interior, in the gap between the original and the Goethe glass and outdoors. T2 - 93rd Annual Meeting of DGG and Annual Meeting of USTV CY - Nuremberg, Germany DA - 13.05.2019 KW - Medieval glasses KW - Stained glasses KW - EDX Analysis KW - Corrosion PY - 2019 AN - OPUS4-48025 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Bosch, S. A1 - Rabin, Ira A1 - Hahn, Oliver T1 - Scientific service project z02 at the CSMC: material science methods of reconstructing the history of manuscripts N2 - Z02 is one of the three technically supporting projects at the Centre for the Study of Manuscript Cultures (CSMC). In collaboration with the other two service projects, Z01 and Z03, it aims at bridging the gap between humanities and natural sciences and technology. To that purpose, we set up a laboratory with a range of high-end instruments, most of them mobile, allowing thorough non-destructive analysis of manuscripts. In addition to working on constantly improving the laboratory and the methods of analysis, a substantial part of our activities is dedicated to service, by supporting different research projects conducted at the centre. In this talk, we will present our equipment and the possibilities offered by the different techniques available regarding the different kinds of missions: typology and classification of inks, provenance studies, recovery of faded inscriptions and palimpsests, reconstruction of the history of manuscripts, authentication and dating. We will give a brief overview of our past and ongoing activities in the frame of the second phase of the CSMC. Finally, a selection of three projects will be presented in greater detail to highlight the possibilities of our laboratory and the diversity of missions which can be carried out. T2 - International Medieval Conference CY - Leeds, United Kingdom DA - 01.07.2019 KW - Manuscript KW - Ink KW - Pigment PY - 2019 AN - OPUS4-48465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, P. T1 - Archaeometric analysis of inks from Coptic Manucripts N2 - Understanding the technological evolution of inks from Coptic Manuscripts. T2 - III International PAThs Conference CY - Rome, University of La Sapienza, Italy DA - 25.02.2019 KW - Archaeometry PY - 2019 AN - OPUS4-48037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Herrmann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in oil and gas facilities. SRM act upon the metal by the re-activeness of hydrogen sulfide (HS-), and by withdrawal of the available electrons in electrical contact with the metal (EMIC). Methanogenic archaea (MA) can also cause MIC (Mi-MIC). Several MAs were identified to be corrosive by using elemental iron as the sole electron donor for methanogenesis, including Methanobacterium­-affliated IM1 and Methanococcus maripaludis Mic1c10. Currently, low corrosion rates were reported for MA, possibly due to the formation of siderite (4Fe + 5HCO3- + 5H+ ® 4FeCO3 + CH4 + 3H2O). Since MA do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of MA, we studied the EMIC methanogenic strains (IM1 and Mic1c10) individually or part of a syntrophic co-culture with SRM. Corrosion studies were conducted using an in-house developed flow-through system to simulate fluctuating environmental conditions. Results indicate that the rates of iron corrosion by MA (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr) and the co-culture (0.1 mm/yr). Scanning electron microscopy (SEM) images of the metal incubated with MA showed severe pitting corrosion. Genomic analysis of the EMIC MA was conducted to provide an insight on the possible cellular mechanisms that could be involved. Furthermore, low concentrations of MA-targeting biocides will be applied to EMIC MA in static and flow conditions to gain insights for possible mitigation strategies. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC. T2 - 7th International Symposium on Applied Microbiology and Molecular Biology in Oil Systems CY - Halifax, Canada DA - 18.06.2019 KW - MIC KW - Microbiologically influenced corrosion KW - Methanogens KW - SRB KW - Corrosion KW - Metalls PY - 2019 AN - OPUS4-48392 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Influence of carbon feeding on a pyrometallurgical Ta and Nb recycling process and the formation of carbides N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage. T2 - Euopean Metallurgical Conference (EMC) 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Pyrometallurgy KW - Tantalum KW - Carbide formation KW - Reduction process KW - Carbon feeding PY - 2019 AN - OPUS4-48351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ghigo, Tea A1 - Rabin, Ira ED - Buzi, P. T1 - Detecting Early Medieval Coptic literature in Dayr Al-Anba Maqar, Between textual conservation and literary rearrangement: The case of Vat. Copt. 57 N2 - The study of the VAt.Copt. 57 at the Vatican Library. Codicological, palaeographical, textual and archaeometrical considerations. KW - Coptic KW - Archaeometry KW - Ink KW - Manuscripts PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-494004 SN - 978-88-210-1025-5 SP - 77 EP - 83 PB - Biblioteca Apostolica Vaticana AN - OPUS4-49400 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, Paola T1 - Archaeometric analysis of Egyptian inks from Late Antiquity N2 - Presentation of the results obtained on a corpus of Egyptian papyri from Late Antiquity T2 - Research Showcase: studying Greco-Roman Egypt CY - University of Basel, Switzerland DA - 26.09.2019 KW - Ink KW - Archaeometry KW - Manuscripts KW - Coptic PY - 2019 AN - OPUS4-49969 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, Paola T1 - Archaeometric analisis of Egyptian inks from Late Antiquity N2 - Archaeometric analisis of Egyptian inks from Late Antiquity: presentation of the results obtaine on a curpus of literary and documentary manuscripts. T2 - International congress of papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Coptic KW - Archaeometry KW - Ink KW - Manuscripts PY - 2019 AN - OPUS4-49971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nöller, Renate A1 - Danielewski, A. A1 - Giel, R. A1 - Overgaauw, E. A1 - Hahn, Oliver T1 - Material analysis of Aztec codices in Berlin. Assignment of small fragments compiled as cutouts on one plate in Humboldt’s “Atlas pittoresque du voyage” N2 - The collection Manuscripta Americana in Berlin consists of fragmented codices acquired by Alexander von Humboldt in Mexico. Some of these Humboldt Codices are published as hieroglyphic writings of the Aztecs in “Vues des Cordilleres et Monuments des Peuples indigènes de l’Amerique”. Starting from a special compilation of seven fragments on plate 36 in the “Atlas”, we investigated the corresponding original fragments using material analysis in order to clarify their historical relations. The analyses were carried out with X-ray fluorescence analysis, VIS spectroscopy, and infrared spectroscopy in diffuse reflection and revealed typical indigenous colors like cochineal, indigo, and organic yellows (e.g. mangrove and zacatlaxcalli). Four fragments under investigation show exactly the same material and thus must once have belonged together in one compendium. An additional manuscript from Mizquiahuala also shown on plate 36 can be matched to another one that is not published in the “Atlas”. KW - Manuscripts KW - Alexander von Humboldt KW - Non-destructiv testing KW - Colourants KW - Writing materials PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-498971 DO - https://doi.org/10.1080/20548923.2019.1682816 SN - 2054-8923 SP - 1 EP - 14 PB - Routledge, Taylor & Francis Group CY - London AN - OPUS4-49897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -