TY - THES A1 - Vandrich, Jasmina T1 - Metabolic engineering in Halomonas elongata N2 - Halomonas elongata is a halophilic γ-proteobacterium that synthesizes and accumulates the compatible solute ectoine to cope with osmotic stress in saline environments. Ectoine possesses protecting properties and stabilizes proteins as well as whole cells against stresses like ionizing radiation and cytotoxins. These properties make ectoine a highly demanded ingredient in cosmetics and pharmaceuticals. To date H. elongata is the industrial Producer strain of ectoine, but several metabolic factors for optimum ectoine production remain to be explored. In this work, we used up to date Metabolic engineering approaches following the ‘Push, Pull, Block – strategy’ to examine targets that contribute to ectoine synthesis. Firstly, the basics of glucose catabolism were inspected to PUSH and enhance carbon flow towards ectoine synthesis. Secondly, lysine biosynthesis was targeted to BLOCK a pathway that is competing for precursors with ectoine synthesis. Thirdly, the mechanosensitive (MS) channels of H. elongata have been examined as possible excretion routes for ectoine. An overexpression of the ectoine excretion channels potentially could PULL out product at the end of ectoine synthesis and increase overall ectoine flux. For the interrogation of central metabolic pathways, we established the new molecular tool CRISPR-mediated interference (CRISPRi) for targeted modulation of gene expression. PUSH Glucose catabolism through the Entner-Doudoroff (ED) and Emden-Meyerhof-Parnas (EMP) pathway was targeted with CRISPRi and examined on gene expression level for ist response to changing salinity and different carbon sources. Changing salinity did not influence gene expression levels of glucose catabolism but the carbon source glucose triggered glycolysis through the (ED) pathway. When gene expression of the ED pathway was downregulated with CRISPRi, the growth rates remained constant. The observations indicate a metabolic overflow mechanism for glycolysis, in which fluxes are constantly high - even at lower salinity when no resources are demanded for ectoine synthesis. The further analysis of glucose to product conversion rates will advise optimum conditions for future industrial cultivation processes. BLOCK Lysine biosynthesis was downregulated with CRISPRi, which led to a significant increase in ectoine production. Hence, the blockage of lysine biosynthesis would be a valuable strategy for the optimization of the industrial producer strain in future studies. PULL MS channels and ectoine regulation are inevitably connected in osmoadaptation. Therefore, ectoine excretion, growth performance and gene expression levels of the MS channels were monitored in steady state conditions and in response to osmotic shock in the wildtype strain and in a MS channel deletion mutant. We observed that the MS channels were essential for the survival of osmotic shock but surprisingly their presence reduced cell growth under high salinity. The MS channels were only partially responsible for ectoine excretion. Thus, alternative ectoine excretion channels must exist and remain to be explored. KW - Halomonas elongata KW - Ectoine KW - CRISPR dCas9 PY - 2019 SP - 1 EP - 94 CY - Potsdam AN - OPUS4-51094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - An, Biwen Annie A1 - Voordouw, G. ED - An, Biwen Annie T1 - Chapter 4. Microbial Communities Involved in High Salinity Souring in Shale Oil Fields N2 - This book chapter provides an overview of the negative impacts of halophilic microorganisms in oil and gas operations. The chapter used a Canadian shale oil reservoir as an case study example to show the high souring and corrosion potential of halophilic microorganisms. KW - Corrosion KW - Halophilic KW - Microorganism KW - Microbial community modelling KW - Oil and gas reservoir KW - Shale KW - Geological formation KW - Oilfield PY - 2019 SN - 13 978-1-138-05775-3 SP - 57 EP - 69 PB - CRC Press CY - Boca Raton ET - 1. AN - OPUS4-49599 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahrig, M. A1 - Torge, Manfred T1 - 3D Inspection of the restoration and conservation of stained glass N2 - The initial focus of this research was on the development of a general workflow for the documentation and monitoring of historical stained glass windows using structured light scanning. Therefore windows from different churches, time periods and with different corrosion and damage phenomena were scanned before and after conservation measures. T2 - 27th CIPA International Symposium “Documenting the past for a better future” CY - Ávila, Spain DA - 01.09.2019 KW - Stained glass KW - Restoration and conservation KW - Structured light scanning KW - 3D inspection KW - Glass scanning PY - 2019 AN - OPUS4-49600 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Microbiology / biofilms in material research and testing N2 - In the modern world there is an increased understanding that design and performance monitoring of materials have to be tested in connection to chemical, physical and (micro)biological challenges. A systematic study on how biofilms interact with materials and what could be done to engineer biofilms and/or materials in order to maximize the resistance of the material (surface) or the resistance the biofilm-modified material (bulk) is in strong need. In the Department “Materials and the Environment” of the BAM new experimental platform is being developed. With the help of different type of device for high throughput and microbiologically-controlled environment simulation we establish a new approach to clarify the mechanisms of biofilm/material interactions. Despite the focus on fundamental research, the main results of this project proposal will be transferable into material technology and construction chemistry and will influence the development of standardization in this topic. As the interactions of biofilms and materials have implications for most constructions as well as climate change, the results of the research generates additional value. T2 - Initialgespräch - DFG-Forschungsgruppe "Mikrobiologie/Biofilme" CY - Karlsruhe, Germany DA - 14.11.2019 KW - Biofilm KW - Microbiology KW - Black fungi KW - Solar panel PY - 2019 AN - OPUS4-50199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life on the rocks - Black fungi from biofilms on material-atmosphere interface N2 - Interface between the atmosphere and mineral substrates is the oldest terrestrial habitat. Morphologically simple microbial biofilms were the first settlers on these inhospitable surfaces at times when the Earth was inhabited only by microorganisms and the solid substrates represented only by natural rock surfaces i.e. lithosphere. Miniature, self-sufficient microbial ecosystems continue to develop on subaerial (i.e. air-exposed) solid surfaces at all altitudes and latitudes where direct contact with the atmosphere and solar radiation occurs – on rocks, mountains, buildings, monuments, solar panels. All these sub-aerial biofilms develop under fluctuating and hostile conditions – and thus frequently harbour stress-tolerant black fungi inherently able to cope with the stresses of bright sunlight and constantly changing atmospheric conditions. Black fungi – a polyphyletic group of Ascomycetes– accumulate the dark pigment DHN melanin, diverse carotenoids and mycosporines in their cells and thus successfully colonise sunlight-flooded habitats from phyllosphere to rock surfaces. Various chemical and physical extremes and fluctuating environments belong to the challenges effectively mastered by black fungi. In our laboratory we isolate novel black fungi from man-made habitats like building materials and solar panels. Using Knufia petricola A95 as a model we conduct experiments to clarify interactions of black fungi with inorganic substrates. We use available mutants to determine the functional consequences of changes in the outer cell wall envelopes – from excreted EPS to layers of protective pigments. A genetic toolbox to manipulate this Chaetothyriales representative is in further development. Our long-term goal is to understand the fundamental mechanisms how black fungi are able (i) to adhere to dry atmosphere-exposed surfaces, (ii) to survive multiple stresses and (iii) to change the underlying substrates including rocks. T2 - International Symposium on Fungal Stress (ISFUS) CY - São José dos Campos, Brazil DA - 19.05.2019 KW - Subaerial biofilm KW - Melanins KW - Carotenoids KW - Knufia KW - Mineral weathering PY - 2019 AN - OPUS4-50200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life on the rocks and other hard surfaces N2 - The story of how black fungi survive harsh conditions on sun-exposed desert rocks and material surfaces is fascinating. In the presentation examples of how knowledge of these organisms can be of practical value (e.g., in biodeterioration studies, such as on stone markers in cemeteries) would be given. Among other stories, the example of how roof tiles amended with a titanium oxide layers as a biocide actually selected for the black fungi will be told. A hypothesis about how these organisms would likely be found on solar panels and some early BAM work in that area will be presented. This then brings the connection to a study ripe for investigation in North Carolina. The talk presents the development of a study aiming at deciphering the influence of microbial biofilm formation on the energy conversion efficiency of solar photovoltaic panels or modules at two facilities (one facility under the impact of high intensity of animal agriculture and high deposition of ammonia from atmosphere and the other with low animal agriculture and lower atmospheric ammonia deposition) in North Carolina. The main hypothesis of the study is that microbial biofilm formation on solar photovoltaic panels will lead to significant decreases in energy conversion efficiency of solar photovoltaic modules and biofilm formation will also be accelerated by high ammonia concentration in the ambient atmosphere and high nitrogen deposition. T2 - Dr. Michael D. Aitken Symposium CY - Chapel Hill, NC, USA DA - 08.11.2019 KW - Black fungi KW - Solar panel KW - Biofilm PY - 2019 AN - OPUS4-50125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Sturkenboom, I. T1 - Chinese paper in Persian manuscript: Preliminary results of a of a codicological, technological and scientific study N2 - In the 15th century, Persian manuscripts underwent significant and lasting changes. Possibly as a response to the import of tinted and gold-decorated paper from China, which was used for manuscript production in Greater Iran, Persian papers were also tinted and embellished with gold-decorated and marbled margins or frames. In a joint project between CSMC and the University of St Andrews, we aim to analyse papers and their decorations in Persian The analyses aim to determine the consistencies of papers, pigments and metals and the techniques used for their production and application. The support will be first described in its codicological characteristics such as dimensions, thickness, colour (expressed in colour coordinates), pattern left from the sieve (observed in transmitted light). The plant used as raw material in paper production will be studied by fibres analysis, while the sizing agents, the pigments, dyes and metals will be analysed by the application of several methods: in particular Reflectography, X-Ray Fluorescence and InfraRed, Raman and Visible Reflectance Spectroscopy. The results of the analyses will form an important resource for the material aspects of Persian manuscripts and be a starting point for establishing a first chronology of the materials and techniques used in Persian manuscript production. An example of the application of the techniques on the analysis of a fragment from a 15th c. Persian Manuscript will be provided. T2 - The Second International Seminar on Traditional Writing and Printing Materials (Fudan University) CY - Shanghai, Republic of China DA - 12.11.2019 KW - Persian manuscript KW - Chinese paper KW - Paper tinting KW - UV-VIS reflectance spectroscopy KW - XRF KW - ATR PY - 2019 AN - OPUS4-50131 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Ink for papyri, ink of papyrus: Recipes from the Arabic world N2 - Papyrus was in use in the Islamic world until the 11th century and few ink recipes collected from treatises about the art of the books are dedicated to this support. But papyrus was also burnt in order to obtain soot used as an ingredient for a particular type of ink (midād al-qarāṭīs). In this talk I will give an overview of the recipes – in particular those by ar-Rāzī –, their context and transmission in order to evaluate this double nature of papyrus, which is considered at the same time a writing support and a material to be recycled. Moreover, I will discuss what kinds of ink are most likely to be found, according to these literary sources, on Arabic manuscripts and documents written on papyrus and compare them to the typologies mentioned for paper and parchment. These results are the premises of a research project starting at the beginning of 2019, in which a number of dated fragments from several European institutions will be analysed with non-destructive techniques in order to establish a profile of the main writing media used in the early centuries of the Islamic Era. T2 - 29th International Congress of Papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Inks KW - Arabic recipes KW - Papyrus PY - 2019 AN - OPUS4-50158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Fifty shades of black: Typologies and terminology of black inks in the light of new discoveries N2 - The identification of the materials constituting an artefact is the basis of any correct conservation project. For this reason (among others) in the last 50 years analytical techniques have been applied to the study of manuscripts. Unfortunately, the scientific investigation of Arabic books is still uncommon, focusing mainly on single case studies of illuminated manuscripts where the black media used to write the text is largely overlooked. This lack of knowledge prompted a recent research in which black ink recipes have been collected from written Arabic sources, their feasibility has been assessed, and some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, mostly non-invasive and non-destructive, in order to build a database of Arabic inks and their ingredients and to verify the detection limits of the equipment employed. Finally, the results were compared to the data collected from historical manuscripts. In this talk I will focus on the ink typologies and the terminology (ancient and modern) used to describe them. In particular I will highlight how even the modern classification fails to capture the variety encountered in both recipes and manuscripts, particularly in the light of recent discoveries. I will address especially the terminological and conceptual issues of mixed inks – in the form of carbon inks and tannins, of carbon and iron gall inks, and of carbon and metallic salts –, iron gall inks made without vitriol and iron gall inks made with sources of tannins different from gall nuts. T2 - First International Conference Oriental Manuscripts: Codicology and Conservation issues CY - Saint Petersburg, Russia DA - 04.12.2019 KW - Ink terminology KW - Codicology KW - Non destructive analytical techniques PY - 2019 AN - OPUS4-50159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Ink recipes from the islamic era: Texts, manuscripts, ink reproductions and scientific analyses N2 - Ink recipes can often be found in Arabic manuscripts. They may be included in treatises of diverse subjects – from handbooks for secretaries or calligraphers to books on arts and crafts, to alchemical and astrological essays. Recipes can also appear, with or without relation to the main text in the manuscript, in the form of lists or collections or even added in empty spaces as single entries. Why were these recipes written down? Were they used by the many professionals dealing with inks in their every-day work? Or were they part of the literary genre of adab with little or no practical application? To answer these questions a research project was set up: ink recipes have been collected from written Arabic sources, their feasibility has been assessed and some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, most non-invasive and non-destructive, and the results compared to the data obtained by the application of the same analyses on concrete manuscripts. The codicological characteristics of the manuscripts have also been studied. My aim in this talk is to show how such an interdisciplinary approach could be beneficial for the study of material culture. T2 - Broadening Horizons 6 CY - Berlin, Germany DA - 24.06.2019 KW - Inks KW - Arabic Recipes KW - Non destructive analytical techniques PY - 2019 AN - OPUS4-50160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Analyses of decorated papers: Potential and preliminary results on persianate manuscripts from 15th – 17th centuries N2 - This talk will be divided into two parts. In the first part I will present the analytical techniques and the equipment used by the Centre for the Study of Manuscript Cultures that can be applied for the study of decorated papers. The analyses aim to determine the constituent materials of papers, pigments, dyes and metals and the techniques used for their production. I will focus in particular on the kind of information these techniques allow us to gather: through optical microscopy we conduct fibre analysis in order to identify the plant used as raw material in paper production while Reflectography, X-Ray Fluorescence and InfraRed, Raman and Visible Reflectance Spectroscopy are used to study the sizing agents, the pigments, dyes and metals. In the second part I will show some results obtained by the application of these techniques on a few Persianate manuscripts, dating between the 15th and 17th centuries, belonging to the corpus of Ilse Sturkenboom. T2 - Symposium Decorated Paper in Early Modern Islamic Cultures CY - Istanbul, Turkey DA - 23.11.2019 KW - XRF KW - UV-VIS Reflectance spectroscopy KW - Fibre analysis KW - Persian manuscripts KW - Chinese Paper KW - FTIR spectroscopy PY - 2019 AN - OPUS4-50161 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Hahn, Oliver A1 - Rabin, Ira T1 - A black ink by any other name...: Typologies of arabic inks and their detection limits N2 - In this poster we will present some results of a research projects dealing with Arabic recipes of black inks [1-2]. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. We will show procedures and problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on squid ink [3] and mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect [4]. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol, the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts. [1] A. Schopen, Tinten und Tuschen des arabisch-islamischen Mittelalters, Göttingen: Vandenhoeck & Ruprecht, 2004 [2] S. Fani, Le arti del libro secondo le fonti arabe originali. I ricettari arabi per la fabbricazione degli inchiostri (sec. IX-XIII): loro importanza per una corretta valutazione e conservazione del patrimonio manoscritto, PhD thesis, Napoli: Università L’Orientale, 2013 [3] S. Centeno, J. Shamir Journal of Molecular Structure, 873 (2008), 149-159 [4] C. Colini et. al, Manuscript cultures, 11 (2018) 43-50 T2 - Jahrestagung „Archäometrie und Denkmalpflege 2019“ CY - Vienna, Austria DA - 11.09.2019 KW - Inks KW - Reflectography KW - XRF KW - Raman Spectroscopy KW - ATR PY - 2019 AN - OPUS4-50162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia ED - Hahn, Oliver ED - Rabin, Ira T1 - A black ink by any other name... Typologies of Arabic inks and their detection limits N2 - In this poster we will present some results of a research projects dealing with Arabic recipes of black inks. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. We will show procedures and problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on squid ink and mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol, the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts. T2 - Jahrestagung „Archäometrie und Denkmalpflege 2019“ CY - Vienna, Austria DA - 11.09.2019 KW - Inks KW - Reflectography KW - XRF KW - Raman Spectroscopy KW - ATR PY - 2019 SN - 0947-6229 VL - Sonderheft 9 SP - 93 EP - 96 PB - Deutsches Bergbau-Museum Bochum CY - Bochum AN - OPUS4-50163 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Sturkenboom, I. T1 - Analyses of paper, tinting and illumination in persian manuscripts held in the Golestan Palace library N2 - In the 15th century, Persian manuscripts underwent significant and lasting changes. Possibly as a response to the import of tinted and gold-decorated paper from China, which was used for manuscript production in Greater Iran, Persian papers were also tinted and embellished with gold-decorated and marbled margins or frames. In a joint project between CSMC and the University of St Andrews, and in co-operation with the Golestan Palace Museum, we aim to analyse papers and their decorations in manuscripts in the holdings of the Golestan Palace Library. The analyses aim to determine the consistencies of papers, pigments and metals and the techniques used for their production and application. The support will be first described in its codicological characteristics such as dimensions, thickness, colour (expressed in colour coordinates), pattern left from the sieve (observed in transmitted light). The plant used as raw material in paper production will be studied by fibres analysis, while the sizing agents, the pigments, dyes and metals will be analysed by the application of several methods: in particular Reflectography, X-Ray Fluorescence and InfraRed, Raman and Visible Reflectance Spectroscopy. The results of the analyses will be published in an online database that will form an important resource for the material aspects of Persian manuscripts and be a starting point for establishing a first chronology of the materials and techniques used in Persian manuscript production. T2 - DFG workshop at Golestan Palace CY - Tehran, Iran DA - 07.04.2019 KW - Persian manuscripts KW - Chinese paper KW - Non destructive analytical techniques KW - Tinting KW - Gold PY - 2019 AN - OPUS4-50164 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tan, K. H. A1 - Sattari, S. A1 - Beyranvand, S. A1 - Faghani, A. A1 - Ludwig, K. A1 - Schwibbert, Karin A1 - Böttcher, C. A1 - Haag, R. A1 - Adeli, M. T1 - Thermoresponsive Amphiphilic Functionalization of Thermally Reduced Graphene Oxide to Study Graphene/Bacteria Hydrophobic Interactions N2 - An understanding of the interactions of 2D nanomaterials with pathogens is of vital importance to developing and controlling their antimicrobial properties. In this work, the interaction of functionalized graphene with tunable hydrophobicity and bacteria is investigated. Poly-(ethylene glycol)-block-(poly-N-isopropylacrylamide) copolymer (PEG-b-PNIPAM) with the triazine joint point was attached to the graphene Surface by a nitrene [2 + 1] cycloaddition reaction. By thermally switching between hydrophobic and hydrophilic states, functionalized graphene sheets were able to bind to bacteria. Bacteria were eventually disrupted when the functionality was switched to the hydrophobic state. On the basis of measuring the different microscopy methods and a live/dead viability assay, it was found that Escherichia coli (E. coli) bacteria are more susceptible to hydrophobic interactions than B. cereus bacteria, under the same conditions. Our investigations confirm that hydrophobic interaction is one of the main driving forces at the presented graphene/bacteria interfaces and promotes the antibacterial activity of graphene derivatives significantly. KW - 2D nanomaterials KW - Functionalized graphene KW - Antimicrobial KW - Hydrophobic interaction PY - 2019 DO - https://doi.org/10.1021/acs.langmuir.8b03660 VL - 35 IS - 13 SP - 4736 EP - 4746 PB - ACS Publications AN - OPUS4-49235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhang, Q. A1 - Zheng, M. A1 - Huang, Y. A1 - Kunte, Hans-Jörg A1 - Wang, X. A1 - Liu, Y. A1 - Zheng, C. T1 - Long term corrosion estimation of carbon steel, titanium and its alloy in backfill material of compacted bentonite for nuclear waste repository N2 - The container of high-level radioactive waste (HLRW) being in deep geological disposal, the backfill material is needed to serve as the second defense for HLRW and the highly compacted bentonite is generally selected. As the time goes, the underground water will infiltrate the backfill, causing the corrosion of materials for the building of containers in the formed electrolyte. Carbon steel, titanium and its alloy are the potential candidate materials for the fabrication of HLRW containers. The current investigation aims at assessing the safety of HLRW container in deep geological disposal for hundreds of thousands of years and facilitating the material selection for future Container fabrication by estimating their corrosion behavior in compacted bentonite with a series of moisture content at different temperatures through electrochemical methods including open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curve (PC) measurements. The corrosion rates were estimated for a carbon steel, a pure titanium and a titanium alloy in compacted Gaomiaozi Bentonite infiltrated with simulated underground water in Beishan area of China over an expected disposal period up to 106 years respectively, showing that titanium and its alloy are more reliable materials for building HLRW containers than carbon steel. KW - Issues KW - Disposal KW - Performance KW - Moisture KW - Lifetime KW - Water KW - Model PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-492413 DO - https://doi.org/10.1038/s41598-019-39751-9 SN - 2045-2322 VL - 9 SP - 3195 PB - Nature Publishing Group AN - OPUS4-49241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehring, Grzegorz A1 - Pronobis-Gajdzis, M. A1 - Targowski, P. A1 - Rabin, Ira T1 - What should we take into an account in the characterization of iron-gall ink by means of X-ray fluorescence? N2 - The earliest known recipes for iron gall inks include four basic ingredients: oak galls – pathological growths of oak leaves; metal salts – usually referred to as vitriol; a binder such as gum Arabic; and water. The final product differs in the elemental composition due to the multitude of recipes as well as differences within the composition of the ink’s ingredients. Nowadays, based on the qualitative and semi-quantitative evaluation of X-ray fluorescence data, it is possible to distinguish inks on the basis of the so-called fingerprint model. The first goal of our study was to determine to what extent the type of XRF spectrometer affects the quality of the ink evaluation. We tested two types of spectrometers, semi-stationary machines equipped with polycapillary focusing optics and a handheld spectrometer with a diaphragm collimator and a relatively big interaction spot. The second goal was to address the issue of whether the ink composition might be affected by storage in a metal container. The presentation will discuss the role of the spectrometer type in the evaluation of a thin layer material such as ink. We have also learned that the iron-gall ink composition might depend on the type of vessel in which ink was being stored. T2 - Konferenz - XIV IADA Congress - Warsaw 2019 CY - Warsaw, Poland DA - 23.09.2019 KW - Iron-gall ink KW - XRF KW - Inkwells KW - Ink composition PY - 2019 AN - OPUS4-49149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kjaervik, Marit A1 - Dietrich, P. A1 - Thissen, A. A1 - Schwibbert, Karin A1 - Brown, J. A1 - Hardie, K. A1 - Unger, Wolfgang T1 - Model systems and sample preparation for surface characterisation of bacteria and biofilms by near-ambient pressure XPS N2 - Bacterial samples are typically freeze dried or cryo-prepared prior to XPS analysis to allow for measurements in ultra-high vacuum (UHV). The sample environment in the near-ambient pressure (NAP) XPS instrument EnviroESCA allows for measurements in up to 15 mbar water vapor, thus, sample preparation is no longer restricted to UHV-compatible techniques. For instance, biofilms grown in medium can be transferred directly from the medium to the measurements chamber, maintaining a humid environment throughout the measurements. Considering the complexity of bacterial samples, sample preparation must be carefully considered in order to obtain meaningful and reproducible results. In this talk, various strategies for sample preparation of bacteria and biofilms for NAP-XPS measurements will be discussed. Model systems of planktonic bacteria, artificial biofilms resembling the exopolysaccharide matrix and biofilms have been characterised in various conditions. The stability and homogeneity of the samples was assessed by monitoring the C1s core level peak at different sample locations. The quality of the XPS-spectra is also influenced by the gas environment, which will be exemplified by core level spectra of P. Fluorescens acquired in air, water vapor and ultra-high vacuum. T2 - 18th European conference on applications of surface and interface analysis (ECASIA) CY - Dresden, Germany DA - 15.09.2019 KW - NAP-XPS KW - Biofilms KW - Bacteria KW - E. coli KW - XPS PY - 2019 AN - OPUS4-49189 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - What is in your opinion the fertiliser of the future? N2 - Conventional fertilisers have their disadvantages as nutrient release is not synchronised with the demand of plants. Several approaches of "next generation fertilisers" are aiming at controlled nutrient release. Recycling fertilisers are often not soluble in water but fully plant available. They are suitable raw materials for the production of new types of controlled release fertilisers. T2 - CLOOP-Workshop "What is in your opinion the fertiliser of the future?" CY - Berlin, Germany DA - 22.10.2019 KW - Controlled release fertilisers KW - Recycling fertilisers PY - 2019 AN - OPUS4-49554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - An, Biwen Annie A1 - Koerdt, Andrea T1 - Investigating and modelling MIC using in-house developed flow system (Hi-Tension) N2 - Microbiologically influenced corrosion is a multidisciplinary research area. To develop successful mitigation strategies, expertise from the industry and research institutes are essential. In Department 4.1, we developed an innovative laboratory flow model (Hi-Tension) that allows effective monitoring of MIC under both standard and non-standard conditions. The flow model allows flexibility with material selection, flow rates, temperature and other environmental parameters changes. Furthermore, the flow model allows integration of electrochemical measurements using microsensors, providing a comprehensive view of corrosion at the biofilm level. Currently, initial results indicate corrosion in the flow model is significantly higher than that of standard laboratory set ups, i.e. static incubations, particularly for methane-producing microorganisms. T2 - Departmental Meeting with Helmotz Dresden CY - BAM, Berlin, Germany DA - 04.11.2019 KW - MIC KW - Corrosion KW - FIB/SEM KW - Corrosion products KW - Hi-Tension KW - Flow Model KW - Modelling PY - 2019 AN - OPUS4-49417 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - An, Biwen Annie A1 - Koerdt, Andrea A1 - Kleinbub, Sherin T1 - Microbial modelling of sulfate-reducing bacteria (SRB) and methanogenic archaea (ME) using iron N2 - Sulfate reducing bacteria (SRB) and methanogenic archaea (MA) are commonly found in the oil and gas environments. The formation of hydrogen sulfide (HS-) is particularly concerning for the petroleum industry due to its corrosiveness. However, the activities of SRB are limited to the concentration of sulfate present in the environment, whereas methanogens can utilize substrates such as H¬2 for methanogenesis. MA is commonly found in sulfate-free environments, such as deep sediments, and are known to form interspecies electron transfer relationships with SRB. Recently, SRB and MA capable of microbiologically influenced corrosion (MIC) by using elemental iron as a direct electron source (EMIC) have gained increased attention. On the iron surface, EMIC-SRB can outcompete EMIC-MA in the presence of sulfate, but this changes as sulfate depletes. The formation of FeS on the metal surface can be further utilized by MA for methanogenesis as it provides a conductive path. However, the possible kinetics involved of the overall process are currently unknown. We obtained a co-culture of EMIC-SRB and EMIC-MA to investigate the growth rates and electrical potential changes under different environmental conditions, including changes in pH, temperature and salinity. Results indicate that under neutral conditions and using iron as the sole substrate, methane production (up to 5 mM) starts after sulfate was depleted. Electrochemical measurements will be conducted on the co-culture under different conditions to determine the changes in the electrical potential in correlation with the sulfate and methane concentration. Fluorescence and electron microscope images of the biofilm structure will be used to visualize cell distribution and morphology. This study embarks the first step of understanding the relationship between EMIC-SRB and EMIC-MA. Such knowledge is important for the field of microbial electrophysiology and can be further explored for industrial applications. T2 - 7th International Symposium on Applied Microbiology and Molecular Biology in Oil Systems (ISMOS-7) CY - Halifax, Canada DA - 18.06.2019 KW - MIC KW - Corrosion KW - FIB/SEM KW - Corrosion products KW - Bacteria KW - Archaea KW - Iron PY - 2019 AN - OPUS4-49420 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kämpf, K. A1 - Schmidt, Alexandra A1 - Bresch, Harald A1 - Bachmann, V. A1 - Kuhlbusch, T. A1 - Schwirn, K. A1 - Völker, D. T1 - Test Guideline on Particle Size and Size Distribution of Manufactured Nanomaterials N2 - The particle size distribution is considered the most relevant information for nanoscale property identification and material characterization. The current OECD test guideline on particle size and size distribution (TG 110) is not applicable to ‘nano-sized’ objects. In this project we thus develop a new OECD test guideline for the measurement of the size and size distribution of particles and fibers with at least one dimension in the nanoscale. A fiber is defined as an object having an aspect ratio of length/diameter l/d >3. The width and length of each fiber should be measured concurrently. In order to measure the particle size distributions, many techniques are available. 9 methods for particles and 2 methods for fibres have been tested in a prevalidation study and appropriate methods will be compared in an interlaboratory round robin test starting in February 2019. T2 - Workshop zur gemeinsamen Forschungsstrategie der Bundesoberbehörden „Nanomaterialien und andere innovative Werkstoffe: anwendungssicher und umweltverträglich“ CY - Berlin, Germany DA - 02.09.2019 KW - OECD KW - Nano KW - Guideline KW - Particle size distributuion KW - Prüfrichtlinie PY - 2019 AN - OPUS4-49507 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Schmidt, Alexandra A1 - Bachmann, V. A1 - Kämpf, K. A1 - Kuhlbusch, T. A1 - Schwirn, K. A1 - Völker, D. ED - Bosse, H. ED - Buhr, E. ED - Dziomba, T. ED - Hodoroaba, Vasile-Dan ED - Klein, T. ED - Krumrey, M. T1 - OECD Test Guideline on particle size and size distribution of manufactured nanomaterials N2 - The properties of nanomaterials are influenced not only by their chemical composition but also by physical properties (such as size, geometry and crystal structure). For the reliable determination and assessment of behaviour and effects of nanomaterials as well as for the determination of the exposure of humans and environment a comprehensive physical-chemical characterization of nanomaterials is essential. This is an important prerequisite to identify them as nanomaterials and to interpret and compare test results and - in future – to forecast interaction and effects of nanomaterials. In 2006, the OECD launched a sponsorship program for the testing of nanomaterials in which 11 nanomaterials were thoroughly investigated using a variety of methods. The aim of the project was, among other things, to find out where problems occur and where there are gaps in the measurement and test procedures and where are changes required. An important outcome of the sponsorship program was the finding that the OECD Test Guidelines should in several cases be extended to the specific needs in testing of nanomaterials. The existing standardized test methods of the OECD for physical-chemical characterization have not been developed for nanomaterials in particular. A high demand for an extension of the test guidelines was identified. Germany complied with the OECD's request in 2017 and has agreed to extend the “Test Guideline on Particle Size Distribution / Fiber Length and Diameter Distributions Test Guideline” for Manufactured Nanomaterials (MN). UBA commissioned BAM and BAuA with the preparation of the Test Guideline. The aim of the project is the development of a harmonized test protocol for a valid and reproducible determination of particle size and size distribution which is one of the most relevant physical-chemical properties for MNs. Different measuring methods provide different results for the size distribution of the particles. This is caused by the different measuring principles of the methods. Each method measures a specific parameter that ultimately determines particle size. First, the measured quantity differs for each method (Scattered light intensity, 2D image / projection, electric mobility, etc.). Second, the calculated diameters of the MN may differ (Feret Diameter, Area Projection, Mobility Diameter, Aerodynamic Diameter, Hydrodynamic Diameter). Third, a measuring method provides a size distribution which is measured either mass-based, surface-based or number-based. A conversion between the results requires additional parameters and thus possibly increases the measurement error. In addition to the technical differences, the individual parameters are strongly influenced by the structure and material of the nanoparticles. For example, a surface functionalization can lead to very different results in the size distribution. The suitability of measurement methods differs with the material of the MN. As a result, two very different results can be measured for the particle size distribution using two different methods, which are nevertheless both correct. Several large projects in recent years therefore concluded that nanomaterials should be characterized by at least two complementary method. Imaging techniques are regarded as one of these methods for the characterization, the complementary methods are supposed to be statistical methods. The different results for the size distribution of nanomaterials become problematic for the registration of new MN. A comparable and reproducible size distribution is a prerequisite for a standardized registration. In the future, the particle size distribution in the EU will also decide on the classification of a substance as a nanomaterial or as a non-nanomaterial. Especially in borderline cases, a standardized and comparable measurement methodology is therefore essential. T2 - NanoWorkshop 2018: Workshop on Reference Nanomaterials CY - Berlin, Germany DA - 14.05.2018 KW - OECD KW - Guideline KW - Particle size distribution KW - Nano KW - Prüfrichtlinie PY - 2019 SN - 978-3-95606-440-1 DO - https://doi.org/10.7795/110.20190412 SN - 0179-0609 VL - F-61 SP - 125 EP - 132 PB - Physikalisch-Technische Bundesanstalt CY - Braunschweig und Berlin AN - OPUS4-49511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kämpf, K. A1 - Bachmann, V. A1 - Bresch, Harald A1 - Schmidt, Alexandra A1 - Kuhlbusch, T. A1 - Schwirn, K. A1 - Völker, D. ED - Bosse, H. ED - Buhr, E. ED - Dziomba, T. ED - Hodoroaba, Vasile-Dan ED - Klein, T. ED - Krumrey, M. T1 - OECD Test Guideline on particle size and particle size distribution of manufactured nanomaterials: simultaneous measurement of length and diameter of fibers N2 - The new OECD test guideline will address the following four main steps in the determination of the length and width distributions of fibers: sample preparation, image acquisition, data evaluation and uncertainty analysis. As the sample preparation has to be optimized for each material, general quality criteria will be given in the protocol. For full visibility of a fiber the appropriate resolution has to be chosen. In the data evaluation the length and diameter of each fiber will be determined concurrently to allow for application of different regulatory definitions. The quality of the results critically depends on the sample preparation as well as the data evaluation. In this step the classification rules have to be formulated and followed accurately in order to optimize reproducibility of the method. The SOP will be validated in an international round robin test, which is planned for 2018/2019. T2 - NanoWorkshop 2018: Workshop on Reference Nanomaterials CY - Berlin, Germany DA - 14.05.2018 KW - OECD KW - Nano KW - Guideline KW - Particle size distributuion KW - Prüfrichtlinie PY - 2019 SN - 978-3-95606-440-1 DO - https://doi.org/10.7795/110.20190412 SN - 0179-0609 VL - F-61 SP - 302 EP - 302 PB - Physikalisch-Technische Bundesanstalt CY - Braunschweig und Berlin AN - OPUS4-49514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwirn, K. A1 - Völker, D. A1 - Ahtianinen, J. A1 - Schmidt, Alexandra A1 - Bresch, Harald A1 - Kämpf, K. A1 - Bachmann, V. A1 - Kuhlbusch, T. ED - Bosse, H. ED - Buhr, E. ED - Dziomba, T. ED - Hodoroaba, Vasile-Dan ED - Klein, T. ED - Krumrey, M. T1 - OECD Test Guidelines development for chemicals safety assessment of nanomaterials N2 - The OECD test guidelines (TGs) for testing chemicals have been widely used for regulatory purposes all over the world since the establishment of the Mutual Acceptance of Data (MAD) principle in 1984. This MAD principle ensures that, if a chemical is tested under the Good Laboratory Practice (GLP) conditions accordingly to an OECD TG, the data should be accepted in all OECD countries. The TGs have been developed, harmonized, internationally validated (round robin tests) and adopted by OECD countries to be used for the physical-chemical characterisation, fate estimation, and hazard identification for risk assessment of various chemicals. In addition to the TGs, OECD Guidance Documents (GDs) usually provide guidance on how to use TGs and how to interpret the results. These GDs do not have to be fully experimentally validated, and hence they are not under MAD, but they are based on relevant published scientific research. But are the existing TGs and the related GDs applicable and adequate for the regulatory testing of nanomaterials? In general, for nanomaterials it is accepted that most of the "endpoints" or more precisely measurement variables are applicable. However, for some endpoints new or amended TGs are needed. In addition, several GDs are needed to give more precise advice on the test performance in order to gain regulatory relevant data on nanomaterials. T2 - NanoWorkshop 2018: Workshop on Reference Nanomaterials CY - Berlin, Germany DA - 14.05.2018 KW - OECD KW - Nano KW - Guideline KW - Nanomaterials KW - Prüfrichtlinie PY - 2019 SN - 978-3-95606-440-1 DO - https://doi.org/10.7795/110.20190412 SN - 0179-0609 VL - F-61 SP - 279 EP - 279 PB - Physikalisch-Technische Bundesanstalt CY - Braunschweig und Berlin AN - OPUS4-49515 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Herrmann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC T2 - Einladung zum Kolloquium HZDR – Helmholtz-Zentrum Dresden-Rossendorf CY - Dresden, Germany DA - 24.09.2019 KW - Corrosion KW - MIC KW - Archaea KW - Methanogens KW - Environmental Simulation PY - 2019 AN - OPUS4-49403 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Herrmann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC T2 - Archaea Meeting-Schmitten VAAM Fachgruppe CY - Schmitten, Germany DA - 12.09.2019 KW - Corrosion KW - MIC KW - Archaea KW - Methanogens KW - Environmental Simulation PY - 2019 AN - OPUS4-49405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, Rene A1 - Szuppa, Tony T1 - Monitoring of soil-like materials for potential reuse N2 - Paragraphs 6 to 8 of the proposed amendment to the German Federal Soil Protection and Contaminated Sites Ordinance contain new requirements regarding the application of soil-like material outside of a rootable soil layer. For example, it is intended to enable reusing of soil-like materials containing regulated substances in concentrations between the single and double precautionary values (PV), provided that the limit values for the eluate are complied with. The aim of a running project (funding code UFOPLAN 3716 74 203 0, German Federal Environmental Agency) is to fill data deficits for soil-like materials which meet the above-mentioned criteria to promote circular economy and conservation of natural resources. Different soil-like materials of various origin (for example dredged material, banquet peeling material, urban and meadow soils) are considered with a special focus on PAHs. A major challenge in sample acquisition is the relatively narrow target range of the PAH content between 3 and 6 mg/kg dm considering a high measurement uncertainty at this concentration level. The contents of PAHs, heavy metals and other inorganic elements in solid matter are determined following established standards. In addition, the soil-like materials are characterized concerning particle size, pH, conductivity, SOM, TOC and carbonate content. To determine the eluate concentration, column tests according to DIN 19528 and batch tests according to DIN 19529 at a liquid/solid ratio (L/S) of 2 l/kg and 10 l/kg are performed comparatively. The results show that the new requirements of the planned amendment to the Federal Soil Protection and Contaminated Sites Ordinance certainly opens additional possibilities for reuse of soil-like materials. Even most soil-like materials within 2-3 x PV comply with the eluate value for PAH (0.2 μg/l) both in the batch test and in the column test at L/S 2 l/kg. Selected inorganic substances lead to similar evaluations. Therefore, the application of such soil-like materials outside of rootable soil layers would be possible. Previously, those materials were often used for landfill construction. In the future, a utilization in the adjacent environment by backfilling, recultivation, renaturation, composting or landscaping would be conceivable. T2 - AquaConSoil 2019 -Sustainable Use and Management of Soil, Sediment and Water Resources CY - Antwerp, Belgium DA - 20.05.2019 KW - Soil-like materials KW - Utilization KW - Ordinance on Contaminated Sites and Soil Protection KW - PAH PY - 2019 AN - OPUS4-50022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Hahn, Oliver A1 - Rabin, Ira T1 - A black ink by any other name...: Typologies of Arabic inks and their detection limits N2 - In this poster we will present some results of a research projects dealing with Arabic recipes of black inks. To improve conservation practices of Arabic manuscripts we have assessed the feasibility of the recipes collected from many Arabic sources on bookmaking and reproduced the most common inks. Ink samples were then artificially aged and analysed using an array of analytical techniques, mostly non-invasive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. First, we will provide an overview of the sources [1-2] employed in the study – dating from 9th to 14th century, although the manuscripts in which they can be found dates up to the 20th century – with an eye on the ink typologies (real and perceived by the compilers). Then we will show how, by reproducing the recipes, it was possible to shed light on some oddities in the procedures and the choice of ingredients. In the end we will discuss problems concerning the identification of ink types and ingredients using reflectography (in Vis, IR and UV), X-Ray Fluorescence, Infrared and Raman spectroscopy. The focus will be in particular on mixed inks – both in the form of carbon inks with the addition of tannins and of a mixture of carbon and iron gall inks – which are particularly difficult to detect [3]. We will also examine the results of iron gall inks made with iron filings or nails instead of vitriol and the various precursor used to extract gallic acid that are mentioned in the sources as surrogates of gall nuts. [1] A. Schopen, Tinten und Tuschen des arabisch-islamischen Mittelalters, Göttingen: Vandenhoeck & Ruprecht, 2004 [2] S. Fani, Le arti del libro secondo le fonti arabe originali. I ricettari arabi per la fabbricazione degli inchiostri (sec. IX-XIII): loro importanza per una corretta valutazione e conservazione del patrimonio manoscritto, PhD thesis, Napoli: Università L’Orientale, 2013 [3] C. Colini et. al, Manuscript cultures, 11 (2018) 43-50 T2 - Technart 2019 CY - Bruges, Belgium DA - 07.05.2019 KW - Inks KW - Reflectography KW - XRF KW - Raman Spectroscopy KW - ATR PY - 2019 AN - OPUS4-50112 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - The Interdisciplinary Alchemist: Reproduction and Study of Black Inks from the Islamicate World N2 - The identification of the materials constituting an artefact is the basis of any correct conservation project, for this reason (among others) in the last 50 years analytical techniques have been applied to the study of manuscripts. Unfortunately, the scientific investigation of Arabic books is still uncommon, focusing mainly on single case studies, often producing unclear results, especially for black inks. This lack of knowledge prompted a recent research in which black ink recipes have been collected from written Arabic sources on bookmaking, their feasibility has been assessed, and finally some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, mostly non-invasive and non-destructive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. In this talk I will present some instances of how this approach can help textual criticism, for example in evaluating variants and determining the competence of authors and compilers. At the same time the research highlights how much this scientific work depends on textual studies, especially concerning the identification of ingredients. Moreover, I will focus on some of the problematics I faced both during the textual interpretation and the actual reproduction of the recipes and how they influenced the results of the scientific analyses. In particular I’ll look into the role played by the degree of purity of the components and the function (real and perceived) of some of the ingredients. T2 - International Medieval Conference 2019 CY - Leeds, UK DA - 01.07.2019 KW - Black Ink KW - Arabic Recipes KW - Interdisciplinary PY - 2019 AN - OPUS4-50114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Landsberger, B A1 - Frauendorf, H A1 - Adler, C A1 - Plarre, Rüdiger ED - Nilsen, L ED - Rossipal, M T1 - Capability and Limitations of Anoxic Treatments for Protecting Museum Collections N2 - Without precaution, insects may cause serious damage to museum collections. Quarantine of potentially infested objects can be logistically challenging. Anoxia under controlled Nitrogen atmosphere is a most gentle but also time-consuming method to eradicate insect pests in all kinds of different materials. Treatment results are usually affected by duration, temperature, humidity and residual oxygen content. During a two-year research project, 34 relevant pest insect species of all developmental stages were tested in different materials (wood, paper, wool) to monitor treatment success and to determine optimum treatment parameters. Duration of treatment ranged from one to three weeks at temperatures of 20–27 °C. As expected, results showed significant differences in mortality among tested species. Highest tolerance of hypoxic conditions was found in elder larvae of Hylotrupes bajulus. Although this species is an unlikely museum pest, it may serve as an overall most tolerant reference. Anobiids and other wood boring beetles are more often an issue related to cultural heritage. A combination of three weeks exposure time at maximum 0.5% residual oxygen and 24 °C, alternatively 1% residual oxygen and 27 °C are recommended for infested artefacts. Imbedding materials in general had no influence on mortality. This study was funded by Deutsche Bundesstiftung Umwelt (DBU). T2 - 4th International Conference Integrated Pest Management (IPM) for Cultural Heritage CY - Stockholm, Sweden DA - 21.05.2019 KW - Controlled atmosphere KW - Museum insect pest KW - Anoxia KW - Nitrogen PY - 2019 SN - 978-91-7209-845-9 SP - 202 EP - 210 AN - OPUS4-50349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gerrits, Ruben T1 - Data of "An experimental study of fungal olivine weathering" N2 - This file contains all the data used for the figures shown in the Dissertation of Ruben Gerrits with the title "An experimental study of fungal olivine weathering". In this study, the weathering-affecting, rock-inhabiting fungus, Knufia petricola A95 and the Fe-bearing olivine (Fe0.2Mg1.8SiO4) were selected to investigate fungi-induced effects on mineral dissolution. The availability of a melanin-deficient mutant (ΔKppks) of K. petricola A95, that produced more extracellular polymeric substances (EPS) than the wild type (WT), enabled comparative studies of the role of melanin and EPS in weathering processes. KW - Olivine KW - Weathering KW - Fungus PY - 2019 DO - https://doi.org/10.26272/opus4-48770 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-48770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seneschal-Merz, Karine A1 - Bücker, Michael A1 - Feldmann, Ines T1 - Low melting glasses for transparent and environmentally-resistant enamels N2 - Today glass is broadly used in modern architecture. For indoor applications it is possible to produce decorated glass by using enamel colours and glass painting techniques without any problems. However, this is more limited for applications out of doors. Humidity and environmental pollution attack the surface of the coating and can damage it. There are only a few colours on the market which are resistant towards acids and bases until now. Additionally, most of those colours are opaque. To extend the colour palette, chemically resistant low melting coloured glasses are being developed which are transparent and intensively toned even in thin coating thicknesses. To achieve such an ambitious aim, many parameters have to combine and act in a complex manner. New compositions of lead borosilicate, zinc borosilicate and lead-zinc borosilicate glasses were produced and milled as powder. The thermal properties as well as the environmental stability were analysed. The influence of PbO and ZnO on the thermal properties and the environmental stability were investigated. Evaluation of the fusing results shows that the production and mixture of transparent vitreous enamels for the exterior side of glasses is possible. The tests made it clear that the original materials for making the vitreous enamels must be excellently ground and prepared to achieve a satisfactory result. The method to produce durable vitreous enamels for exterior application also seems to allow the production of glass colours. KW - Low melting glasses KW - Enamels KW - Heavy metal free KW - Corrosion KW - Chemical durability KW - Aging tests KW - Architecture KW - Colored glasses PY - 2019 DO - https://doi.org/10.13036/17533546.60.4.002 SN - 1753-3546 SN - 1753-3554 VL - 60 IS - 4 SP - 97 EP - 104 PB - Society of Glass Technology CY - Sheffield, UK AN - OPUS4-48835 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Trimpert, J. A1 - Groenke, N. A1 - Kunec, D. A1 - Eschke, K. A1 - He, Shulin A1 - McMahon, Dino Peter A1 - Osterrieder, N. T1 - A proofreading-impaired herpesvirus generates populations with quasispecies-like structure N2 - RNA virus populations are composed of highly diverse individuals that form a cloud of related sequences commonly referred to as a ‘quasispecies’1–3. This diversity arises as a consequence of low-fidelity genome replication4,5. By contrast, DNA Virus populations contain more uniform individuals with similar fitness6. Genome diversity is often correlated with increased Fitness in RNA viruses, while DNA viruses are thought to require more faithful genome replication. During DNA replication, erroneously incorporated bases are removed by a 3′-5′ exonuclease, a highly conserved enzymatic function of replicative DNA but not RNA polymerases. This proofreading process enhances replication fidelity and ensures the genome integrity of DNA organisms, including large DNA viruses7. Here, we show that a herpesvirus can tolerate impaired exonucleolytic proofreading, resulting in DNA virus populations, which, as in RNA viruses8, are composed of highly diverse genotypes of variable individual fitness. This indicates that herpesvirus mutant diversity may compensate for individual Fitness loss. Notably, in vivo infection with diverse virus populations results in a marked increase in virulence compared to genetically homogenous parental virus. While we cannot exclude that the increase in virulence is caused by selection of and/or interactions between individual genotypes, our findings are consistent with quasispecies dynamics. Our results contrast with traditional views of DNA virus replication and evolution, and indicate that a substantial increase in population diversity can lead to higher virulence. KW - Marek's virus KW - Virulence KW - Quasispecies KW - Evolution PY - 2019 DO - https://doi.org/10.1038/s41564-019-0547-x SN - 2058-5276 N1 - Corrigendum: Nature Microbiology 4 (2019) 2025 VL - 4 SP - 2175 EP - 2183 PB - Nature Publishing Group CY - London AN - OPUS4-48896 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Uninvited and Welcomed Guests in Museums – Biological management of clothes moths and woodworms N2 - In museums and historic houses clothes, moths (Tineola bisselliella, Tinea pellionella) and the furniture beetle (Anobium punctatum) are the most economically important pests on textiles or wooden artifacts, respectively. Their management is essential to protect cultural ethnological heritage and natural history collections for future generations. Pest management strategies have changed over time. Today, intensive knowledge on pest biology and overall material science are key cornerstones in IPM concepts - also for the museum environment. The important first steps for sustainable pest management are risk assessment, early pest detection and identification of pathways of infestation. These steps are followed by physical and biological means of control, which have lately gained more importance than applying biocides. Several potentially effective biological enemies of clothes moths and woodworm have been known for a long time, but their promotion for pest control in museums and historic houses is just beginning. This short review summarizes current concepts of pest life cycle interruption by applying good quarantine and very specific biological measures. The lessons learned from recent faunistic surveys, life-history studies as well as behavioral observations of parasitoids and predators of clothes moths and woodworm may supplement the pest management tool box. The need for further research in this field is addressed. T2 - IOBC-WPRS CY - Pisa, Italy DA - 03.09.2019 KW - Biological Control KW - Museum Pests KW - Tineola bisselliella KW - Anobium punctatum KW - Apanteles carpatus KW - Baryscapus tineivorus KW - Corynetes caeruleus PY - 2019 AN - OPUS4-48901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pokharel, R. A1 - Gerrits, Ruben A1 - Schuessler, J. A1 - von Blanckenburg, F. T1 - Mechanisms of olivine dissolution by rock-inhabiting fungi explored using magnesium stable isotopes N2 - To unravel the dissolution mechanisms of olivine by a rock-inhabiting fungus we determined the stable isotope ratios of Mg on solutions released in a laboratory experiment. We found that in the presence of the fungus Knufia petricola the olivine dissolution rates were about seven-fold higher (1.04×10−15 mol cm−2 s−1) than those in the abiotic experiments (1.43×10−16 mol cm−2 s−1) conducted under the same experimental condition (pH 6, 25 °C, 94 days). Measured element concentrations and Mg isotope ratios in the supernatant solutions in both the biotic and the abiotic experiment followed a dissolution trend in the initial phase of the experiment, characterized by non-stoichiometric release of Mg and Si and preferential release of 24Mg over 26Mg. In a later phase, the data indicates stoichiometric release of Mg and Si, as well as isotopically congruent Mg release. We Attribute the initial non-stoichiometric phase to the rapid replacement of Mg2+ in the olivine with H+ along with simultaneous polymerization of Si tetrahedra, resulting in high dissolution rates, and the stoichiometric phase to be influenced by the accumulation of a Si-rich amorphous layer that slowed olivine dissolution. We attribute the accelerated dissolution of olivine during the biotic experiment to physical attachment of K. petricola to the Si-richamorphous layer of olivine which potentially results in ist direct exposure to protons released by the fungal cells. These additional protons can diffuse through the Si-rich amorphous layer into the crystalline olivine. Our results also indicate the ability of K. petricola to dissolve Fe precipitates in the Si-rich amorphous layer either by protonation, or by Fe(III) chelation with siderophores. Such dissolution of Fe precipitates increases the porosity of the Si-rich amorphous layer and hence enhances olivine dissolution. The acceleration of mineral dissolution in the presence of a rock-dissolving fungus further suggests that its presence in surficial CO2 sequestration plants may aid to accelerate CO2 binding. KW - Olivine KW - Magnesium KW - Isotopes KW - Fungus PY - 2019 DO - https://doi.org/10.1016/j.chemgeo.2019.07.001 SN - 0009-2541 SN - 1872-6836 VL - 525 SP - 18 EP - 27 PB - Elsevier AN - OPUS4-48824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Gerrits, Ruben T1 - An experimental study of fungal olivine weathering N2 - Free-living and (ecto)-mycorrhizal fungi enhance rock weathering. In their roles as mineral weathering agents and mutualistic partners of phototrophs, fungi supply primary producers like plants and phototrophic microorganisms with mineral-derived nutrients. The exact mechanisms behind fungus-induced mineral weathering processes are however not well understood. Progress can be achieved here by reproducible experimental simulations of the natural processes, using well-characterised model organisms and minerals. In this study, the weathering-affecting, rock-inhabiting fungus, Knufia petricola A95 and the Fe-bearing olivine (Fe0.2Mg1.8SiO4) were selected to investigate fungi-induced effects on mineral dissolution. The availability of a melanin-deficient mutant (ΔKppks) of K. petricola A95, that produced more extracellular polymeric substances (EPS) than the wild type (WT), enabled comparative studies of the role of melanin and EPS in weathering processes. Three experimental systems, which generate long-term microbiological stability, were developed to study the impact of the WT and ΔKppks on olivine weathering: (1) batch and (2) mixed flow dissolution experiments, and (3) biofilm cultivation experiments. In addition, state-of-the-art analytical techniques were used to monitor changes in the growth medium, as well as of the mineral surface and biofilm-mineral interface. Inductively coupled plasma optical emission spectrometry (ICP-OES) analysis of the Mg, Si and Fe concentrations in the reacted growth medium was used to quantify olivine dissolution. In abiotic controls, Mg and Si dissolved congruently, while Fe precipitated. The measured olivine dissolution rates at pH 6 were two orders of magnitude lower than previously reported, but similar at acidic pH. X-ray photoelectron spectroscopy (XPS) analyses of the olivine surface confirmed the presence of Fe (oxyhydr)oxide precipitates. Transmission electron microscopy (TEM) imaging of an abiotically reacted polished olivine section from the long-term cultivation experiment showed the presence of an amorphous layer enriched in Fe. All these observations indicate that the precipitation of Fe (oxyhydr)oxides on the olivine surface inhibits olivine dissolution. Both tested rock-inhabiting fungal strains affect Fe precipitation as well as olivine dissolution. Evaluation of the WT and ΔKppks revealed that the WT formed less biomass but could take up higher amounts of metals (e.g. Fe) and was more efficient in its attachment to olivine. The WT and ΔKppks enhanced olivine dissolution as demonstrated by higher Mg and Si concentration in the reacted growth medium. They furthermore prevented Fe precipitation by binding Fe and retaining it in solution, thereby allowing olivine dissolution to proceed. The WT cells that were attached to the olivine surface were particularly efficient at inhibiting Fe precipitation. By binding Fe directly at the olivine surface, the WT cells removed the inhibition of olivine dissolution almost completely. TEM analysis of polished olivine sections, colonised by a fungal biofilm for seven months, supported this hypothesis. After long-term fungus-olivine interaction, the Fe-enriched, amorphous layer did not develop, and the olivine surface was stronger etched compared to the abiotic control. To study the effect of mutualism on mineral weathering, K. petricola was grown with the cyanobacterium, Nostoc punctiforme ATCC 29133. Both partners showed an enhanced growth and formed a stratified biofilm which attached more strongly to olivine. Nevertheless, the olivine dissolution rate of the fungus-cyanobacterium consortium was moderate. Rock weathering simulation systems developed here are promising research instruments. The experimental conditions allow for the alteration of the studied mineral surface, while the clear definition of these conditions delivers a stable growth of microorganisms. The latter makes these systems universally applicable, especially in combination with integrative multidisciplinary analytics. Processes underlying environmental and biological effects on rock weathering, metal corrosion, plastic degradation, or the deterioration of any other substrate can be studied reproducibly and over a long period of time. The chemical and biological complexity of these simulation systems mimics natural rock weathering processes. The mineral dissolution rates generated in this study are therefore relevant to natural ecosystems. KW - Olivine KW - Weathering KW - Fungus PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:188-refubium-25125-1 DO - https://doi.org/10.17169/refubium-2880 SP - 1 EP - 178 PB - Freie Universität Berlin CY - Berlin AN - OPUS4-48825 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brusamarello-Santos, L. C. C. A1 - Alberton, D. A1 - Valdameri, G. A1 - Camilios-Neto, D. A1 - Covre, R. A1 - Lopes, K. d. P. A1 - Zibetti Tadra-Sfeir, M. A1 - Faoro, H. A1 - Adele Monteiro, R. A1 - Barbosa-Silva, A. A1 - Broughton, William John A1 - Oliveira Pedrosa, F. A1 - Wassem, R. A1 - de Souza, E.M. T1 - Modulation of defence and iron homeostasis genes in rice roots by the diazotrophic endophyte Herbaspirillum seropedicae N2 - Rice is staple food of nearly half the world’s population. Rice yields must therefore increase to feed ever larger populations. By colonising rice and other plants, Herbaspirillum spp. stimulate plant growthand productivity. However the molecular factors involved are largely unknown. To further explore this interaction, the transcription profiles of Nipponbare rice roots inoculated with Herbaspirillum seropedicae were determined by RNA-seq. Mapping the 104 million reads against the Oryza sativa cv. Nipponbare genome produced 65 million unique mapped reads that represented 13,840 transcripts each with at least two-times coverage. About 7.4% (1,014) genes were differentially regulated and of these 255 changed expression levels more than two times. Several of the repressed genes encoded proteins related to plant defence (e.g. a putative probenazole inducible protein), plant disease resistance as well as enzymes involved in flavonoid and isoprenoid synthesis. Genes related to the synthesis and efflux of phytosiderophores (PS) and transport of PS-iron complexes were induced by the bacteria. These data suggest that the bacterium represses the rice defence system while concomitantly activating iron uptake. Transcripts of H. seropedicae were also detected amongst which transcripts of genes involved in nitrogen fixation, cell motility and cell wall synthesis were the most expressed. KW - Herbaspirillum seropedicae KW - Pathogen KW - Rice KW - qPCR KW - Genome PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-490122 DO - https://doi.org/10.1038/s41598-019-45866-w SN - 2045-2322 VL - 9 SP - 10573-1 EP - 10573-15 PB - Nature CY - London AN - OPUS4-49012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred ED - Brion, I. ED - Alloteau, F. ED - Lehuede, P. ED - Majerus, O. ED - Caurant, D. T1 - The effect of particle deposition and climate on glass degradation N2 - Medieval stained-glass windows are protected by an outside gazing system in many churches.The interspace between the original and the protective glass is ventilated with air from the indoor or exterior environment, where dust and particles can move.Cascade impactor measurements and SEM/EDX analyses of sampled dust were carried to determine the dust composition. The effect of particles on model glass samples was investigated in climate chambers under accelerated weathering conditions. The results from in situ measurements and laboratory tests were combined to evaluate the potential effect of particulate matter on historic stained-glass Windows. T2 - International Symposium on Glass Degradation in Atmospheric Conditions CY - Paris, France DA - 15.11.2017 KW - Medieval-stained glass KW - Protective glazing KW - Cascade impector KW - Simulation PY - 2019 SN - 9782705697945 SP - 223 EP - 224 PB - hermann CY - Paris AN - OPUS4-49023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kunte, Hans-Jörg T1 - Effect of Ectoine on DNA: Mechanisms of Interaction and Protection N2 - The compatible solute ectoine is a versatile protectant synthesized by many prokaryotes. It is used as an osmolyte helping microorganisms to maintain an osmotic equilibrium. In addition, ectoine acts as a stabilizer and protects proteins, membranes and whole cells against detrimental effects such as freezing and thawing, drying and high temperatures. Its protective effect is explained by the preferential exclusion model, which postulates that ectoine does not directly interact with biomolecules but is excluded from their surface. Interestingly, details on the interaction of ectoine with DNA are still unknown. Therefore, we studied the influence of ectoine on DNA and the mechanisms by which ectoine protects DNA against ionizing radiation. To emulate biological conditions, we used a sample holder comprising a silicon chip with a Si3N4 membrane, which allows for electron irradiation of DNA in aqueous solution. Analysis by atomic force microscopy revealed that without ectoine, DNA was damaged by irradiation with a dose of 1,7 +/-0,3 Gy. With ectoine, DNA remained undamaged, even after irradiation with 15 Gy. Simulations with dsDNA and ectoine in water revealed a preferential binding of the zwitterionic ectoine to the negatively charged DNA. According to the simulations, binding of ectoine will destabilize dsDNA. Destabilizing is probably caused by the transition of B-DNA to A-DNA and will reduce the DNA melting temperature, which was experimentally proven. The preferential binding provides a stable ectoine shell around DNA, which allows ectoine to reduce OH-radicals and electrons near the DNA and thereby mitigating the damaging effect of ionizing radiation. T2 - Halophiles 2019 CY - Cluj-Napoca, Romania DA - 24.06.2019 KW - Ectoine KW - Ionizing radiation KW - Preferential binding PY - 2019 AN - OPUS4-48618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Werner W. A1 - Wöhlecke, Andreas T1 - Zero leakage? Landfill liner and capping systems in Germany N2 - An approach to achieve 'zero leakage' is discussed with respect to experience in Germany, where strict regulations for landfill lining and capping Systems have been developed and issued because of large environmental Problems related to landfills that accumulated in the 1970s and 1980s. Using a thick, high-quality high-density Polyethylene (HDPE) geomembrane (GM) that is installed free of residual waves and wrinkles in intimate contact with a compacted clay liner or geosynthetic clay liner of very low permeability, by a qualified, experienced, well-equipped and properly third-party-controlled installer, and which is protected by heavy protection layers designed with respect to the long-term performance of the GM may result in a liner or capping system of practically no leakage. This is demonstrated by analysing results of measurements obtained from permanently installed leak-detection Systems in combination with HDPE GMs. The survey was based on 32 German landfills with 1.276.500 m² of installed GMs. KW - Geomembranes KW - Landfill KW - Landfill lining PY - 2019 DO - https://doi.org/10.1680/jenge.16.00031 SN - 2051-803X VL - 6 IS - 3 SP - 1600031, 162 EP - 170 PB - ICE AN - OPUS4-48626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Smol, M. A1 - Adam, Christian T1 - Towards circular economy for phosphorus in Poland N2 - In the transition to the Circular Economy (CE) model, where the added value of products is kept as long as possible and waste is eliminated, the sustainable management of raw materials plays a key role. In above CE model, especial attention is paid to CRMs which are economically and strategically important for the European economy, but have a high-risk associated with their supply. One of the most important element which can not be replaced and is an essential element for human nutrition, yet limited resource is phosphorus (P). An importance of issues related to sustainable P management results from EU legislation, which indicated P as a Critical Raw Material (CRM). The sustainable management of P-resources is especially important for the Baltic region. A consequence of waterborne loads passing into the sea, mainly as wastewater with a high P content is the eutrophication of the Baltic Sea environment. Due to the largest inputs of P (37%) into the Baltic Sea originate from Poland, the development of sustainable solutions aimed at more rational P management for this country is externally important. T2 - International Phosphorus Workshop 9 CY - Zurich, Switzerland DA - 08.07.2019 KW - Phosphorus recovery KW - Circular economy PY - 2019 AN - OPUS4-48614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Del Mastro, G. A1 - Hammerstaedt, J. A1 - Mocella, V. A1 - Rabin, Ira T1 - XRF ink analysis of selected fragments from the Herculaneum collection N2 - Hundreds of papyrus rolls, carbonized during the 79CE eruption of Mount Vesuvius, were discovered in 1754 at Herculaneum. Sophisticated mechanical methods for unrolling the best-preserved scrolls have been applied, with varying success. However, such processes have been abandoned, to prevent risk from irremediable damage or loss and to preserve the integrity of the extremely fragile rolls. Following the development of X-ray based non-invasive techniques, attempts to virtually unroll the scrolls were made. The most common ink in Antiquity was carbon-based, and the main element of carbonized papyrus is carbon, making these investigations difficult. However, some attempts with synchrotron X-ray phase-contrast tomography (XPCT) were successful. Recently, the identification of antique inks containing metals raised hope that if some of the inks contain metal the rolls can be virtually unrolled using conventional CT- technique. We are presenting here the first results of a preliminary analysis, which aimed at identifying scrolls whose ink contains metals. T2 - Konferenz: 29th International Congress of Papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Herculaneum KW - Papyrus KW - Tomography KW - XRF KW - Ink PY - 2019 AN - OPUS4-48615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Smol, M. A1 - Adam, Christian T1 - Possibility of recovering phosphorus from sewage sludge ash (SSA) in Poland N2 - Due to the vital importance of phosphorus (P) and its increasing scarcity as a natural resource, phosphorus recovery has recently gained significant scientific and technical interest. An interesting sources of phosphorus are sewage sludge (SS) and sewage sludge ash (SSA) due to the major part of the phosphate from P rich wastewater is transferred to the sludge (approx. 90%). Despite the fact that the raw materials base is large (PURE report indicates that in 2020 the amount of sewage sludge generated in Poland will reach 180% of the dry matter of sewage sludge produced in 2010), at present recycling of phosphorus is not a commonly used practice in Poland. T2 - International Phosphorus Workshop 9 CY - Zurich, Switzerland DA - 08.07.2019 KW - Sewage sludge ash KW - Phosphorus recovery PY - 2019 AN - OPUS4-48616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Adam, Christian A1 - Stolle, Dirk A1 - Spanka, M. A1 - Auer, G. T1 - Thermochemical treatment of waste products from iron and steel production N2 - Blast furnace (BF) sludge and electric arc furnace (EAF) dust are typical wastes that incur from iron and steel production. In addition to iron, calcium, carbon, and silicon they usually contain high concentrations of heavy metals such as zinc, lead, and cadmium that are potentially hazardous to the environment, rendering disposal in landfills ecologically problematic and costly. Consequently, pyrometallurgical, hydrometallurgical, and hybrid methods for selective elimination of non-ferrous heavy metals from BF sludge and EAF dust have been conceived, of which only the carbothermic reduction route taken in the so-called Waelz rotary kiln process has been proven to be economically successful. However, this process has several drawbacks regarding efficiency of heavy-metal removal and recovery of iron, and it does not allow processing of BF sludge. In this study, we investigated the efficiency and feasibility of selective chlorination and evaporation of non-ferrous heavy metals, particularly zinc and lead, in both BF sludge and EAF dust as an alternative, thermochemical processing route. To this end, hydrochloric acid and iron(II) chloride solution have been used as chlorinating agents, and the process of heavy-metal chlorination and evaporation has been investigated under inert operating conditions, at variable chlorine concentrations, and at temperatures between 500 and 1200 °C. High zinc and lead removal efficiencies of > 99.5 % were achieved with both chlorinating agents, but iron(II) chloride turned out to be overall more efficient for removal of zinc and lead from BF sludge and EAF dust. Interestingly, and in contrast to previous studies, the iron was completely retained in the processed solid residue, therefore rendering the processed residues virtually zinc- and lead-free raw materials that may either be used internally (e.g., feeding processed BF sludge and EAF dust back into the respective furnaces) or externally (e.g., for cement production). T2 - European Metallurgical Conference 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Blast furnace sludge KW - Electric arc furnace dust KW - Recycling KW - Selective chlorination KW - Zinc PY - 2019 SN - 978-3-940276-89-6 VL - 3 SP - 1267 EP - 1282 PB - GDMB CY - Clausthal-Zellerfeld AN - OPUS4-48362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Influence of carbon feeding on a pyrometallurgical tantalum and niobium recycling process and the formation of carbides N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage. T2 - Euopean Metallurgical Conference (EMC) 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Pyrometallurgy KW - Tantalum KW - Carbide formation KW - Reduction process KW - Carbon feeding PY - 2019 SN - 978-3-940276-87-2 VL - 1 SP - 371 EP - 386 PB - GDMB Verlag GmbH CY - Clausthal-Zellerfeld AN - OPUS4-48363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Adam, Christian A1 - Stolle, Dirk A1 - Spanka, M. A1 - Auer, G. T1 - Thermochemical treatment of waste products from iron and steel production N2 - This presentation summarizes the development of a novel thermochemical process for recycling of zinc and lead-bearing wastes (blast furnace sludge and electric arc furnace dust) that accumulate during iron and steel production. T2 - European Metallurgical Conference 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Blast furnace sludge KW - Electric arc furnace dust KW - Recycling KW - Selective chlorination KW - Zinc PY - 2019 AN - OPUS4-48364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steger, Simon A1 - Oesterle, D. A1 - Bretz, S. A1 - Frenzel, L. A1 - Stege, H. A1 - Winkelmeyer, I. A1 - Hahn, Oliver A1 - Geiger, G. T1 - Kandinsky’s fragile art: a multidisciplinary investigation of four early reverse glass paintings (1911–1914) by Wassily Kandinsky N2 - This work highlights the rediscovery of the technique of reverse glass painting by the artists of the “Blaue Reiter” collective in the early 20th-century and focusses particularly on the role of Wassily Kandinsky (1866–1944). Kandinsky created more than 70 reverse paintings on glass and showed several of them in exhibitions together with paintings on canvas and cardboard, implying a coequal importance of these techniques. Four of his early (1911–1914) reverse glass paintings (Auferstehung, Allerheiligen II, Rudern, Apokalyptischer Reiter II) were selected for investigation and their iconography, painting techniques and painting materials were examined. Two paintings were executed on so-called cathedral glass, revealing a “hammered surface”, whereas Kandinsky used a corrugated glass panel for Rudern. A multi-analytical, non-invasive approach [X-ray fluorescence (XRF), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), VIS spectroscopy (VIS), Raman spectroscopy] was taken to identify the pigments and classify the binding media. The results reveal a broad palette of materials. Several pigments like lead white, zinc white, Strontium yellow, Prussian blue, viridian, cadmium yellow, ultramarine blue, cinnabar and carbon black were found in most of the four paintings. The use of the rare synthetic organic pigments PR60 and PB52 is discussed. In two works of art, cadmium carbonate is associated with cadmium yellow. The identification of aluminium foil along with tin foils in Rudern indicates an early use of this material for reverse glass paintings. KW - Reverse glass painting KW - Non-invasive analysis KW - Raman spectroscopy KW - DRIFTS PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-480075 DO - https://doi.org/10.1186/s40494-019-0268-8 VL - 7 IS - 27 SP - 1 EP - 17 PB - Springer AN - OPUS4-48007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steger, Simon A1 - Stege, H. A1 - Bretz, S. A1 - Hahn, Oliver T1 - A complementary spectroscopic approach for the non-invasive in-situ identification of synthetic organic pigments in modern reverse paintings on glass (1913–1946) N2 - This work addresses the identification of synthetic organic pigments (SOP) in eight modern reverse paintings on glass (1913–1946) by means of an in-situ multi-analytical approach. We combined the complementary properties of mobile Raman spectroscopy and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) to overcome the main disadvantages of each method: extensive band overlapping in DRIFT spectra and fluorescence problems in Raman spectra. A collection of DRIFTS reference spectra enables a precise pigment identification by DRIFTS and establishes this method as a serious non-destructive alternative for the identification of SOP. The group of β-naphthol pigments yielded valuable results for both methods, whereas synthetic alizarin (PR83) was preferentially detected by DRIFTS. Finally, uncommon triaryl carbonium pigments and two azo group-based yellows were identified in the paintings by means of Raman spectroscopy. KW - Synthetic organic pigments KW - DRIFTS KW - Raman spectroscopy KW - Reverse glass painting PY - 2019 DO - https://doi.org/10.1016/j.culher.2019.01.011 SN - 1296-2074 SN - 1778-3674 VL - 38 SP - 20 EP - 28 PB - Elsevier Masson SAS. AN - OPUS4-48008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Stege, H A1 - Bretz, S. A1 - Hahn, Oliver T1 - A complementary spectroscopic approach for the non invasive in situ identification of synthetic organic pigments in modern reverse paintings on glass N2 - This work addresses the identification of synthetic organic pigments (SOP) in ten modern reverse paintings on glass (1912-1946) by means of an in-situ multi-analytical approach. The combination of the complimentary properties of mobile Raman spectroscopy and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) enabled the detection of sixteen SOP even in complex mixtures with inorganic compounds and binders. For the β-naphthol pigments, both Raman and DRIFTS yield appropriate results. DRIFTS was the preferred method for the detection of synthetic alizarin (PR83). Its diagnostic band pattern even allows its detection in complex mixtures with mineral pigments, binders and fillers. Raman spectroscopy yielded distinctive spectra for the triaryl carbonium pigments (PG1, PV2, PR81) and the two-yellow azo SOP (PY3, PY12), whereas DRIFT spectra were affected by extensive band overlapping. This may also occur in Raman spectra, but in less problematic amounts. Fluorescence is the major problem with Raman and it significantly hampers the SOP spectra even with the 785 nm laser. On the one hand the big spot size of DRIFTS (10 mm) limits the technique to rather large sampling areas, whereas the use of a 50× objective for in-situ Raman measurements permits a focus on small spots and aggregated SOP flakes. Moreover, “environmental” factors like temperature changes, artificial light, limited space and vibrations when people pass by need to be considered for in-situ measurements in museums. Finally, the results show the experimental use of SOP in modern reverse glass paintings. Among several rare SOP (e.g. PB52, PR81), two of them (PG1, PV2) have never been reported before in any artwork. T2 - Technart2019 CY - Bruges, Belgium DA - 07.05.2019 KW - Synthetic organic pigments KW - Reverse glass painting KW - DRIFTS KW - Raman spectroscopy PY - 2019 AN - OPUS4-48009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -