TY - CONF A1 - Wilke, Olaf T1 - Emission Testing for Indoor Products N2 - The chemical emissions from products are tested by means of emission test chambers under defined conditions (climate, loading, air change rate). The standard method for the determination of volatile organic compounds (VOC) is the sampling onto Tenax-tubes followed by thermal desorption (TDS) and gas chromatography-mass spectrometry (GC-MS) analysis. The EU-LCI list includes some very volatile organic compounds (VVOC) and some VOC for which there are limitations when using the standard method. For VVOC additional sampling is required using stronger absorbers like Carbotrap or multi-bed adsorption tubes. The analysis of VVOC also requires a different GC oven program and a different column for the separation. For the determination of formaldehyde and other low boiling aldehydes (e.g. acetaldehyde, acetone, propanal, propenal) DNPH-cartridges are used which are extracted with acetonitrile followed by liquid chromatography (HPLC-UV) analysis. The derivatisation of propenal and other unsaturated aldehydes (e.g. 2-butenal) with DNPH might lead to lower findings due to incomplete derivatization and forming of by-products. For a better quantification of acetic acid the use of ion chromatography (IC) is recommended because the analysis of acetic acid with the standard method (TDS) leads to lower findings due to break through during sampling. The use of ion chromatography for the analysis of organic acids requires a third sampling technique. The acids are adsorbed onto silica-gel and extracted with water. T2 - ISESISIAQ 2019 CY - Kaunas, Lituania DA - 18.08.2019 KW - Indoor Air Quality KW - Emission Testing KW - Indoor Products KW - VOC Emission KW - Construction Products PY - 2019 AN - OPUS4-49406 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohr, Gunther A1 - Seeger, Stefan A1 - Hilgenberg, Kai T1 - Measurement of particle emissions in Laser Powder Bed Fusion (L-PBF) processes and its potential for in-situ process monitoring N2 - Laser Powder Bed Fusion (L-PBF) is a promising additive manufacturing (AM) technology for metal part production especially for complex and lightweight structures or functional designs. In L PBF processes several by-products including welding plume and its condensates, spatter and ejected powder are generated during laser exposure. Investigations of micro- and nano-sized by-products have received little attention in literature. This study focuses on the analysis of particle emissions in L PBF of 316L stainless steel using a scattered light aerosol spectrometer and a fast mobility particle sizer spectrometer during the process which allows for in-situ analysis of particle sizes in the range of 6 nm to 100 µm. A distinct correlation of emission signals to part position can be revealed. In addition, a significant influence of laser scanning vector directions on emission signals is presented. Furthermore, differing powder layer thicknesses can be recognised by deviations in emission signals. T2 - Euro PM2019 CY - Maastricht, The Netherlands DA - 13.10.2019 KW - Aerosol measurements KW - Laser Powder Bed Fusion (L-PBF) KW - Additive Manufacturing (AM) KW - Spatter KW - Fume KW - Plume KW - Particle gas emission PY - 2019 AN - OPUS4-49387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohr, Gunther A1 - Seeger, Stefan A1 - Hilgenberg, Kai T1 - Measurement of particle emissions in Laser Powder Bed Fusion (L-PBF) processes and its potential for in-situ process monitoring N2 - Laser Powder Bed Fusion (L-PBF) is a promising additive manufacturing (AM) technology for metal part production especially for complex and lightweight structures or functional designs. In L PBF processes several by-products including welding plume and its condensates, spatter and ejected powder are generated during laser exposure. Investigations of micro- and nano-sized by-products have received little attention in literature. This study focuses on the analysis of particle emissions in L PBF of 316L stainless steel using a scattered light aerosol spectrometer and a fast mobility particle sizer spectrometer during the process which allows for in-situ analysis of particle sizes in the range of 6 nm to 100 µm. A distinct correlation of emission signals to part position can be revealed. In addition, a significant influence of laser scanning vector directions on emission signals is presented. Furthermore, differing powder layer thicknesses can be recognised by deviations in emission signals. T2 - Euro PM 2019 CY - Maastricht, The Netherlands DA - 13.10.2019 KW - Plume KW - Laser Powder Bed Fusion (L-PBF) KW - Additive Manufacturing (AM) KW - Spatter KW - Fume KW - Particle gas emission KW - Aerosol measurements PY - 2019 SP - 1 EP - 7 AN - OPUS4-49388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Marie A1 - Vogel, Christian A1 - Adam, Christian A1 - Stephan-Scherb, Christiane A1 - Hecht, Lutz T1 - Novel approaches to Sc species investigation in bauxite residues by x ray absorption near edge structure spectroscopy N2 - In a rapidly evolving world, the demand on raw materials is increasing steadily and many technologies are dependent on a secure supply of hi-tech metals. Recently, scandium (Sc) has attracted attention since its use in high strength Al-alloys and solid-oxide-fuel-cells strongly improves the performance of those materials. The element Sc is not exceptionally rare but quite resistant to geochemical enrichment processes, it is scarcely found enriched to high concentrations and is recovered as a by-product. Since Sc enrichment in Greek bauxite residues was shown by Ochsenkühn-Petropoulou et. al (1994), intensive research on this material and development of efficient Sc-recovery methods is ongoing. This study investigates Sc-bearing species in bauxite residues from alumina production. It aims to provide direct evidence about the Sc-speciation’s in those secondary resources and tries to find the link to speciation’s in primary resources, e.g. bauxites and laterites. Therefore, Sc K edge XANES (X-ray absorption near edge structure) spectroscopy is performed using synchrotron radiation to determine the presence of certain Sc-components and distinguish between adsorbed and chemically bonded Sc as was shown for lateritic deposits in Australia by Chassé et al. 2016. For comparison, reference standards of Sc-bearing and Sc-adsorbed species are synthesized. Indirect inferences from leaching behavior of bauxites, in cases supported by analyses with LA-ICP-MS, suggest Sc to be associated with either iron- or aluminum phases (Vind et al. 2017); (Suss et al.). It remains unclear how different primary materials influence Sc-speciation in the bauxite residue. Therefore, a comparison between different European bauxite residues is made in this study. The investigations should help to understand Sc chemistry and behavior in different primary and secondary materials and provide fundamentals for metallurgical processing. The research is incorporated in the SCALE project (GA No. 730105) funded by EU Horizon 2020 research and innovation program. T2 - DMG Tagung GeoMünster CY - Westfälische Wilhelms-Universität Münster, Germany DA - 22.09.2019 KW - Scandium KW - Bauxite Residue KW - Red Mud KW - XANES PY - 2019 AN - OPUS4-49389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Simon, Franz-Georg A1 - Meggyes, Tamas ED - Meyers, Robert A. T1 - Sustainable remediation methods for metals and radionuclides N2 - Since it was realized that sites contaminated with metals and radionuclides needed treatment, various remediation methods have been and are being developed. Depending on the size of the contaminated site and urgency of intervention, conventional or recently introduced techniques have been used. Conventional techniques include excavation and removal for treatment of soil and contaminants, or the so-called “pump-and-treat” method, in which contaminated groundwater is removed from the ground by pumping and treated in a treatment plant on the surface. It has the advantage of using proven techniques and is easy to control, and the treated groundwater can be reinjected into the ground or discharged in rivers or lakes. Novel methods include permeable reactive barriers, biomineralization, and electrokinetic remediation. KW - Permeable reactive barriers KW - Groundwater KW - Uranium PY - 2019 SN - 978-1-4939-2493-6 DO - https://doi.org/10.1007/978-1-4939-2493-6_63-3 SP - 1 EP - 37 PB - Springer Science+Business Media, LLC CY - Heidelberg ET - 1 AN - OPUS4-48816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pokharel, R. A1 - Gerrits, Ruben A1 - Schuessler, J. A1 - von Blanckenburg, F. T1 - Mechanisms of olivine dissolution by rock-inhabiting fungi explored using magnesium stable isotopes N2 - To unravel the dissolution mechanisms of olivine by a rock-inhabiting fungus we determined the stable isotope ratios of Mg on solutions released in a laboratory experiment. We found that in the presence of the fungus Knufia petricola the olivine dissolution rates were about seven-fold higher (1.04×10−15 mol cm−2 s−1) than those in the abiotic experiments (1.43×10−16 mol cm−2 s−1) conducted under the same experimental condition (pH 6, 25 °C, 94 days). Measured element concentrations and Mg isotope ratios in the supernatant solutions in both the biotic and the abiotic experiment followed a dissolution trend in the initial phase of the experiment, characterized by non-stoichiometric release of Mg and Si and preferential release of 24Mg over 26Mg. In a later phase, the data indicates stoichiometric release of Mg and Si, as well as isotopically congruent Mg release. We Attribute the initial non-stoichiometric phase to the rapid replacement of Mg2+ in the olivine with H+ along with simultaneous polymerization of Si tetrahedra, resulting in high dissolution rates, and the stoichiometric phase to be influenced by the accumulation of a Si-rich amorphous layer that slowed olivine dissolution. We attribute the accelerated dissolution of olivine during the biotic experiment to physical attachment of K. petricola to the Si-richamorphous layer of olivine which potentially results in ist direct exposure to protons released by the fungal cells. These additional protons can diffuse through the Si-rich amorphous layer into the crystalline olivine. Our results also indicate the ability of K. petricola to dissolve Fe precipitates in the Si-rich amorphous layer either by protonation, or by Fe(III) chelation with siderophores. Such dissolution of Fe precipitates increases the porosity of the Si-rich amorphous layer and hence enhances olivine dissolution. The acceleration of mineral dissolution in the presence of a rock-dissolving fungus further suggests that its presence in surficial CO2 sequestration plants may aid to accelerate CO2 binding. KW - Olivine KW - Magnesium KW - Isotopes KW - Fungus PY - 2019 DO - https://doi.org/10.1016/j.chemgeo.2019.07.001 SN - 0009-2541 SN - 1872-6836 VL - 525 SP - 18 EP - 27 PB - Elsevier AN - OPUS4-48824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred ED - Brion, I. ED - Alloteau, F. ED - Lehuede, P. ED - Majerus, O. ED - Caurant, D. T1 - The effect of particle deposition and climate on glass degradation N2 - Medieval stained-glass windows are protected by an outside gazing system in many churches.The interspace between the original and the protective glass is ventilated with air from the indoor or exterior environment, where dust and particles can move.Cascade impactor measurements and SEM/EDX analyses of sampled dust were carried to determine the dust composition. The effect of particles on model glass samples was investigated in climate chambers under accelerated weathering conditions. The results from in situ measurements and laboratory tests were combined to evaluate the potential effect of particulate matter on historic stained-glass Windows. T2 - International Symposium on Glass Degradation in Atmospheric Conditions CY - Paris, France DA - 15.11.2017 KW - Medieval-stained glass KW - Protective glazing KW - Cascade impector KW - Simulation PY - 2019 SN - 9782705697945 SP - 223 EP - 224 PB - hermann CY - Paris AN - OPUS4-49023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Borzekowski, Antje A1 - Anggriawan, R. A1 - Auliyati, M. A1 - Kunte, Hans-Jörg A1 - Koch, Matthias A1 - Rohn, S. A1 - Karlovsky, P. A1 - Maul, Ronald T1 - Formation of Zearalenone Metabolites in Tempeh Fermentation N2 - Tempeh is a common food in Indonesia, produced by fungal fermentation of soybeans using Rhizopus sp., as well as Aspergillus oryzae, for inoculation. Analogously, for economic reasons, mixtures of maize and soybeans are used for the production of so-called tempeh-like products. For maize, a contamination with the mycoestrogen zearalenone (ZEN) has been frequently reported. ZEN is a mycotoxin which is known to be metabolized by Rhizopus and Aspergillus species. Consequently, this study focused on the ZEN transformation during tempeh fermentation. Five fungal strains of the genera Rhizopus and Aspergillus, isolated from fresh Indonesian tempeh and authentic Indonesian inocula, were utilized for tempeh manufacturing from a maize/soybean mixture (30:70) at laboratory-scale. Furthermore, comparable tempeh-like products obtained from Indonesian markets were analyzed. Results from the HPLC-MS/MS analyses show that ZEN is intensely transformed into its metabolites alpha-zearalenol (alpha-ZEL), ZEN-14-sulfate, alpha-ZEL-sulfate, ZEN-14-glucoside, and ZEN-16-glucoside in tempeh production. alpha-ZEL, being significantly more toxic than ZEN, was the main metabolite in most of the Rhizopus incubations, while in Aspergillus oryzae fermentations ZEN-14-sulfate was predominantly formed. Additionally, two of the 14 authentic samples were contaminated with ZEN, alpha-ZEL and ZEN-14-sulfate, and in two further samples, ZEN and alpha-ZEL, were determined. Consequently, tempeh fermentation of ZEN-contaminated maize/soybean mixture may lead to toxification of the food item by formation of the reductive ZEN metabolite, alpha-ZEL, under model as well as authentic conditions. KW - Modified mycotoxins KW - Zearalenone sulfate KW - a-zearalenol KW - Food fermentation KW - Rhizopus and Aspergillus oryzae PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-491126 DO - https://doi.org/10.3390/molecules24152697 VL - 24 IS - 15 SP - 2697 PB - MDPI AN - OPUS4-49112 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nöller, Renate A1 - Feldmann, Ines A1 - Kasztovszky, Z. A1 - Szőkefalvi-Nagy, Z. A1 - Kovács, I. T1 - Characteristic Features of Lapis Lazuli from Different Provenances, Revised by µXRF, ESEM, PGAA and PIXE N2 - The objective of this study is to find out, to what extent the geochemical characteristics of lapis lazuli can be utilized in respect to its provenance. A wide range of variables is taken into consideration depending on the quantity of samples analysed from a specific geological region and the methods applied. In order to provide evidence, a multi-technique analytical approach using µXRF, ESEM, PGAA and PIXE is applied to samples from the most famous deposits of lapis lazuli. Special elements determined as fingerprints are compared in relation to the forming conditions obvious in textural features. The results and statistical output allow a differentiation that enables an optimized local classification of the blue stone. An absolute requirement for all geo-tracing performed on blue colored cultural objects of unknown provenance is awareness of the limits of analysis. The possible sources of lapis lazuli are tested by analysing the blue pigment used as paint on murals and ink on manuscripts from the Silk Road. KW - Lapis lazuli KW - Micro-XRF KW - ESEM KW - PGAA KW - PIXE KW - Pigment analyses KW - Provenance studies PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-491181 DO - https://doi.org/10.17265/2328-2193/2019.02.003 SN - 2328-2193 VL - 7 IS - 2 SP - 57 EP - 69 PB - David CY - New York, NY AN - OPUS4-49118 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, D. A1 - Kargl, F. A1 - Adam, Christian T1 - Formation and chemical stabilisation of tricalcium-silicate during solidification from the melt of post-treated metallurgical slags N2 - Tricalcium-silicate (C3S) or Alite is the most important mineral in Portland cement. Since pure tricalcium-silicate is only stable above temperatures of 1250 °C, its decomposition has to be prevented technically by fast cooling after the sintering process. At room temperature, the decomposition velocity is very slow so that metastable tricalcium-silicate is obtained. Although the mechanisms of clinker phase formation during burning process of Portland cement in a rotary kiln were solved and improved over the years, in view of possible economic and ecological benefits current projects aim to produce clinker phases from metallurgical slags. Recent studies discovered that the mineral phase which remained after a reducing treatment and separation of formed metallic iron from molten Linz-Donawitz (LD-) slags contained about 60 wt.% Alite despite it was cooled slowly. Because the results could be verified using slags from different origins and varying cooling velocities a chemical stabilisation of the Alite can be assumed. First tests in mortars indicate that workability, hardening and solid state properties are comparable with an ordinary Portland cement. An application of the observed phenomenon in cement production requires enhanced knowledge about formation and stabilisation conditions of Alite during crystallisation from melts in contrast to the sintering reactions in conventional Portland cement production. Therefore, this study focuses on the stabilisation mechanisms of Alite in consolidating melts. Samples from different melting experiments are analysed to determine stabilising factors. T2 - 15th International Congress on the Chemistry of Cement CY - Prag, Czech Republic DA - 16.09.2019 KW - Tricalcium-silicate KW - Portland Cement KW - Alite KW - Steelmaking slag PY - 2019 SP - Paper 492, 1 EP - 10 AN - OPUS4-49050 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -