TY - JOUR A1 - Vogel, Christian A1 - Scholz, Philipp A1 - Kalbe, Ute A1 - Caliebe, W. A1 - Tayal, A. A1 - Vasala, S. J. A1 - Simon, Franz-Georg T1 - Speciation of antimony and vanadium in municipal solid waste incineration ashes analyzed by XANES spectroscopy N2 - The use of ashes from municipal solid waste incineration as secondary building materials is an important pillar for the circular economy in Germany. However, leaching of potential toxic elements from these materials must be at environmentally acceptable levels. Normally, a three-month ageing period immobilizes most hazardous heavy metals, but antimony (Sb) and vanadium (V) showed previously unusual leaching. In order to clarify the mechanisms, we analyzed the Sb and V species in various bottom and fly ashes from municipal waste incineration by XANES spectroscopy. Antimony oxidizes from Sb(+ III) species used as flame retardants in plastics to Sb(+ V) compounds during waste incineration. However, owing to the similarity of different Sb(+ V) compound in the Sb K- and L-edge XANES spectra, it was not possible to accurately identify an exact Sb(+ V) species. Moreover, V is mainly present as oxidation state + V compound in the analyzed ashes. However, the coarse and magnetic fraction of the bottom ashes contain larger amounts of V(+ III) and V(+ IV) compounds which might enter the waste incineration from vanadium carbide containing steel tools. Thus, Sb and V could be critical potential toxic elements in secondary building materials and long-term monitoring of the release should be taken into account in the future. KW - Müllverbrennung KW - XANES spectroscopy PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-599841 SN - 1438-4957 SP - 1 EP - 7 PB - Springer Science and Business Media LLC AN - OPUS4-59984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 1. Nachtrag zum Zulassungsschein 06/BAM 4.3/01/14 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 1. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601147 SP - 1 EP - 6 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 1. Nachtrag zum Zulassungsschein 06/BAM 4.3/01/19 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 1. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601159 SP - 1 EP - 6 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 08/BAM IV.3/04/04 für eine geotextile Schutzlage als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen N2 - 3. Nachtrag zum Zulassungsschein für eine geotextile Schutzlage als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen der Fa. HUESKER Synthetic GmbH. KW - Deponie KW - Zulassung KW - Schutzschicht PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601315 SP - 1 EP - 21 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60131 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 6. Nachtrag zum Zulassungsschein 08/BAM IV.3/08/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 6. Nachtrag zum Zulassungsschein für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Fa. Naue GmbH & Co. KG. KW - Deponie KW - Zulassung KW - Geotextilien PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601324 SP - 1 EP - 19 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60132 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 6. Nachtrag zum Zulassungsschein 08/BAM 4.3/02/14 für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen N2 - 6. Nachtrag zum Zulassungsschein für ein Kunststoff-Dränelement für Deponieoberflächenabdichtungen der Fa. Naue GmbH & Co. KG. KW - Deponie KW - Zulassung KW - Kunststoff-Dränelement PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601339 SP - 1 EP - 27 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60133 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 11. Nachtrag zum Zulassungsschein 08/BAM 8.3/10/94 für eine Vliesstoffmatte als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen N2 - 11. Nachtrag zum Zulassungsschein für eine Vliesstoffmatte als Bestandteil einer Schutzschicht aus geosynthetischer Schutzlage und feinkiesiger mineralischer Schutzlage für Dichtungsbahnen in Deponieabdichtungen der Fa. Naue GmbH & Co. KG. KW - Deponie KW - Zulassung KW - Schutzschicht PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601343 SP - 1 EP - 20 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60134 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 08/BAM IV.3/10/10 für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen N2 - 3. Nachtrag zum Zulassungsschein für Vliesstoffe zum Filtern und Trennen für Deponieabdichtungen der Fa. HUESKER Synthetic GmbH. KW - Deponie KW - Zulassung KW - Geotextilien PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601307 SP - 1 EP - 25 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60130 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 06/BAM IV.3/02/07 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 3. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601245 SP - 1 EP - 9 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60124 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 06/BAM IV.3/03/07 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 3. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601285 SP - 1 EP - 9 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 2. Nachtrag zum Zulassungsschein 06/BAM 4.3/04/16 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 2. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601269 SP - 1 EP - 6 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60126 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 3. Nachtrag zum Zulassungsschein 06/BAM IV.3/04/99 für Kunststoffdichtungsbahnen (KDB) in Basis- und Überflächenabdichtungen von Deponien N2 - 3. Nachtrag zum Zulassungsschein für Kunststoffdichtungsbahnen (KDB) in Basis- und Überflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601298 SP - 1 EP - 6 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60129 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Wöhlecke, Andreas T1 - 2. Nachtrag zum Zulassungsschein 06/BAM 4.3/05/16 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien N2 - 2. Nachtrag zum Zulassungsschein 06/BAM 4.3/05/16 für Kunststoffdichtungsbahnen (KDB) in Basis- und Oberflächenabdichtungen von Deponien der Fa. AGRU Kunststofftechnik GmbH. KW - Deponie KW - Zulassung KW - Kunststoffdichtungsbahn PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-601270 SP - 1 EP - 7 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-60127 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Simon, Franz-Georg A1 - Scholz, Philipp A1 - Gleis, Markus ED - Thiel, Stephanie ED - Thome-Kozminesky, Elisabeth ED - Quicker, Pater ED - Gosten, Alexander ED - Stengler, Ella T1 - Einstufung von Aschen und Schlacken aus der Abfallverbrennung im Hinblick auf die weitere Verwertung N2 - There are two mirror entries in the European Waste Catalogue for bottom ash and slag from waste incineration: 19 01 11* and 19 01 12. Entry 19 01 11* describes a waste material containing hazardous substances. It was shown that only the hazardous property HP14 (ecotoxic) is of relevance for the classification. If substances with the hazard statement code (HSC) H400, H410, H411, H412 and H413 are present in incineration bottom ash (IBA) above certain level the waste is classified as hazardous, otherwise it is non-hazardous (in this case 19 01 12). It was further shown that only Cu, Zn and Pb compounds have an impact on the classification using a summation rule: 100xΣ c(H410) + 10xΣ c(H411) + Σ c(H412). Limit value is 25 percent. It is obvious that H410 substances have the highest impact. Therefore, the knowledge of the elemental composition of IBA is not sufficient because the content of distinct chemical compounds (with the respective molecular weight) is needed. When the exact speciation is not known a worst-case approach has to be applied. A practical guideline for the estimation of HP14 was developed based on the definition of 4 substance groups: 1. Metals and alloys, 2. Water-soluble substances, 3. Oxides and carbonates and 4. Substances not soluble in weak acids. In substance group 1 only fine Zn powder has the HSC H410. Water-soluble substances are assumed to be H410 substances. Their concentrations are, however, regularly below the cut-off value of 0.1 %. The amount of substance group 3 is estimated by a selective extraction with maleic acid. According to the worst-case approach it is assumed that CuCO3xCu(OH)2 and ZnO represent the respective Cu and Zn species in IBA because these substances have the highest stochiometric factor. Even with this worst-case approach results from operators of IBA treatment plant showed that the limit value of 25 % is not exceeded. The requirements for utilization of IBA in Germany are defined in the Secondary Building Materials Decree (Ersatzbaustoffverordnung EBV) which was set into force in August 2023. Leaching methods (batch test or column test) with a liquid-to-solid ratio of 2 l/kg are applied. IBA fulfills the requirements for class HMVA-2. Actually, even a classification of IBA as hazardous (i.e 19 01 11*) would not affect utilization but handling and transport. KW - Rostasche KW - Ökotoxizität KW - Ersatzbaustoffverordnung KW - XANES-Spektroskopie PY - 2024 SN - 978-3-944310-90-9 VL - 1 SP - 402 EP - 414 PB - TK-Verlag CY - Neuruppin ET - 1 AN - OPUS4-59465 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Simon, Franz-Georg A1 - Pienkoß, Fabian T1 - INTEGRAL - Integriertes Konzept für mineralische Abfälle und Landmanagement zur nachhaltigen Entwicklung von Stadt-Land-Nutzungsbeziehungen, Teilvorhaben 4: BAM, Ermittlung stofflicher Parameter N2 - Zusammenfassend wurde in dieser Arbeit gezeigt, dass die Setzmaschinentechnik eine geeignete Methode ist, um Brechsande aus gemischten Bauabfällen aufzubereiten. Die Trennung des Materials in zwei Stoffströme unterschiedlicher Dichte hat sich mit einer Absenkung um 56% besonders effizient in der Reduzierung von PAK Belastungen im Feststoff erwiesen. Auch die Sulfatlast im Produktstrom wurde durch den Prozess im Vergleich zum Aufgabegut um 29% gesenkt. Neben der Erhöhung des Median Partikeldurchmessers durch Klassierungseffekte, ist die Herabsetzung verschiedener Eluatparameter ebenfalls positiv zu bewerten. Dies bezieht sich zum einen auf die elektrische Leitfähigkeit, die nach EBV von RC-3 auf RC-1 aufgewertet wurde und zum anderen auf die Chromkonzentration, die von RC-2 auf die Stufe RC-1 angehoben wurde. Die vorliegenden Aufbereitungsergebnisse erlaubten jedoch nicht eine Gesamteinordnung des Materials als Ersatzbaustoff oberhalb der Klasse RC-3. Hierzu ist eine weitere Absenkung der Eluatwerte für Sulfat um 25% von RC-3 (1325 mg L-1) auf RC-2 (< 1000 mg L-1) und des PAK-15 Wertes um 4% von RC-3 (8.3 µg L-1) auf RC-2 (< 8.0 µg L-1) erforderlich. Eine detaillierte Optimierung der Prozessparameter der Setzmaschinentechnik könnten diesen Spielraum ermöglichen. KW - Setzmaschine KW - Nassaufbereitung KW - Ersatzbaustoff PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-600263 N1 - Das diesem Bericht zugrunde liegende Vorhaben wurde mit Mitteln des Bundesministeriums für Bildung und Forschung unter dem Förderkennzeichen 033L223D gefördert. SP - 1 EP - 18 PB - Technische Informationsbibliothek (TIB) CY - Hannover AN - OPUS4-60026 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Scholz, Philipp A1 - Gleis, Markus T1 - Aschen und Schlacken aus der Abfallverbrennung im Lichte der Ersatzbaustoffverordnung N2 - Im Rahmen eines vom Umweltbundesamt geförderten Forschungsprojekts wurde untersucht, ob die Abtrennung der Feinfraktion (0-2 mm) eine Verbesserung der umweltrelevanten Eigenschaften bewirkt und somit HMVA-1 erreicht werden kann. In Deutschland wird die Rostasche durch Nassentschlackungssysteme aus dem Feuerraum ausgetragen. Durch den Kontakt mit Wasser setzen direkt hydraulische Reaktionen ein, die eine vollständige Abtrennung der Feinfraktion unmöglich machen. Das wurde bereits in den 1990er Jahren erkannt und führte zur Entwicklung des ABB InRec Verfahrens mit Trockenentaschung als ersten Verfahrensschritt. Auch damals war das Ziel eine möglichst inerte Rostasche für die Verwertung zu erzeugen. In den letzten Jahren wurden in der Schweiz Trockenentaschungssystem installiert, hier vor allem um die Rückgewinnung von elementaren Metallen auch in der Feinfraktion zu verbessern. Welche Potenziale sich dabei erschließen lassen, wurde in einem anderen UBA-Projekt untersucht. Im Rahmen unserer Arbeiten wurde versuchsweise trockene Rostasche an einer Anlage in Süddeutschland genommen und im Labor untersucht. Im Vortrag werden die Ergebnisse zum Auslaugverhalten und zur Gefahreneigenschaft HP14 (Ökotoxizität) vorgestellt. T2 - Jahrestreffen 2024 der DECHEMA-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung (AuW) und Gasreinigung (GAS) CY - Dresden, Germany DA - 25.03.2024 KW - Rostasche KW - Ersatzbaustoffe PY - 2024 AN - OPUS4-59985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scholz, Philipp A1 - Falkenhagen, Jana A1 - Wachtendorf, Volker A1 - Brüll, Robert A1 - Simon, Franz-Georg T1 - Investigation on the Durability of a Polypropylene Geotextile under Artificial Aging Scenarios N2 - Geosynthetics are widely used in various civil engineering applications, such as geotextiles in coastal protection, and display a sustainable alternative to natural mineral materials. However, the full benefits of using geosynthetics can only be gained with a long service lifetime of the products. With the use of added stabilizers to the polymers, service lifetimes can be achieved in the range of 100 years. Therefore, accelerated aging methods are needed for the assessment of the long-term performance of geotextiles. In the present study, the behavior of geosynthetic materials made of polypropylene was investigated under artificial aging conditions involving elevated temperatures ranging from 30 to 80 °C, increased oxygen pressures ranging from 10 to 50 bar in water-filled autoclaves, and UV irradiation under atmospheric conditions. ATR-IR spectroscopy was employed to detect the increase in the carbonyl index over various aging durations, indicating the oxidative degradation of the geotextile. The most pronounced increase was observed in the case of aging through UV irradiation, followed by thermal aging. Elevated pressure, on the other hand, had a lower impact on oxidation. High-temperature size exclusion chromatography was utilized to follow the reduction in molar mass under different degradation conditions, and the results were consistent with those obtained from ATR-IR spectroscopy. In polyolefins such as polypropylene, Hindered Amine Stabilizers (HAS) are used to suppress oxidation caused by UV radiation. The quantitative analysis of HAS was carried out using a UV/Vis method and HPLC. The degradation of UV stabilizers during the aging of geotextiles is responsible for the oxidation and the reduction in the molar mass of polypropylene. From the results, it can be concluded that applications of PP geotextile without soil or sand cover might cause the risk of the formation of microplastic particles. Material selection, design, and maintenance of the construction must follow best practices, including the system’s removal or replacement at end-of-life. Otherwise, a sustainable use of geotextiles in civil engineering is not possible. KW - Geotextiles KW - Microplastic KW - Size exclusion chromatography KW - Accelerated aging PY - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-599739 SN - 2071-1050 VL - 16 IS - 9 SP - 1 EP - 15 PB - MDPI AG CY - Basel AN - OPUS4-59973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Roesch, Philipp A1 - Schinnen, Andrea A1 - Riedel, Maren A1 - Sommerfeld, Thomas A1 - Sawal, G. A1 - Bandow, N. A1 - Vogel, Christian A1 - Kalbe, Ute A1 - Simon, Franz-Georg T1 - Investigation of pH-dependent extraction methods for PFAS in (fluoropolymer-based) consumer products: A comparative study between targeted and sum parameter analysis N2 - Here, we report a comparative study of different sum parameter analysis methods for the extraction of per- and polyfluoroalkyl substances (PFAS) from manufactured consumer products, which can be measured by combustion ion chromatography (CIC). Therefore, a hydrolysis-based extraction method was further developed, which accounts for the addition of hydrolyzable covalently bound polyfluoroalkylated side-chain polymers (SFPs) to the extractable organic fluorine portion of the mass balance proposed as "hydrolyzable organically bound fluorine" (HOF). To test this hypothesis, the method was applied to 39 different consumer products containing fluoropolymers or monomeric PFAS taken from four different categories: outdoor textiles, paper packaging, carpeting, and permanent baking sheets. We also evaluated the method's efficiency by extracting four synthesized fluorotelomer polyacrylate reference compounds. The total fluorine (TF) and extractable organically bound fluorine (EOF) values were measured through CIC using established protocols. The TF values ranged from sub-ppb to %-levels, depending on the compound class. All samples showed results for hydrolyzed organofluorine (HOF) between 0.03 and 76.3 μg/g, while most EOF values were lower (