TY - CONF
A1 - Kjaervik, Marit
A1 - Schwibbert, Karin
A1 - Dietrich, P.
A1 - Thissen, A.
A1 - Unger, Wolfgang
T1 - Surface characterisation of biofilms by nearambient pressure X-ray photoelectron spectroscopy
N2 - The XPS information depth of approximately 10 nm is in the same size range as the outer membrane of the gram-negative bacteria, which makes XPS a suitable tool for determining the elemental composition of the bacterial surface and monitor changes caused by outer stress like dehydration or exposure to antimicrobials. However, bacteria are inherently in a hydrated state, and therefore only compatible to ultra-high vacuum after extensive sample preparation, which may degrade the sample constituents. This issue is addressed by the development of near-ambient pressure (NAP)-XPS, which enables bacteria and biofilms to be characterised in their native wet state. Artificial biofilms, bacteria and biofilms of Escherichia coli have been characterised with the laboratory NAP-XPS instrument EnviroESCA from SPECS GmbH, at pressures ranging from high vacuum to 12 mbar, and in both humid and dry environment. By studying biological samples in their native wet state, new insight about composition and transport of drugs through cell membranes and the extracellular polymeric substance (EPS) of biofilms can be obtained.
T2 - Royal Society of Chemistry Twitter Conference
CY - Worldwide (online conference)
DA - 06.03.2018
KW - Biofilms
KW - E. coli
KW - Alginate
KW - NAP-XPS
PY - 2018
AN - OPUS4-44498
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Kjaervik, Marit
A1 - Ramstedt, M.
A1 - Schwibbert, Karin
A1 - Dietrich, P. M
A1 - Unger, Wolfgang
T1 - Comparative Study of NAP-XPS and Cryo-XPS for the Investigation of Surface Chemistry of the Bacterial Cell-Envelope
N2 - Bacteria generally interact with the environment via processes involving their cell-envelope. Thus, techniques that may shed light on their surface chemistry are attractive tools for providing an understanding of bacterial interactions. One of these tools is Al Kα-excited photoelectron spectroscopy (XPS) with its estimated information depth of <10 nm. XPS-analyses of bacteria have been performed for several decades on freeze-dried specimens in order to be compatible with the vacuum in the analysis chamber of the spectrometer. A limitation of these studies has been that the freeze-drying method may collapse cell structure as well as introduce surface contaminants. However, recent developments in XPS allow for analysis of biological samples at near ambient pressure (NAP-XPS) or as frozen hydrated specimens (cryo-XPS) in vacuum. In this work, we have analyzed bacterial samples from a reference strain of the Gram-negative bacterium Pseudomonas fluorescens using both techniques. We compare the results obtained and, in general, observe good agreement between the two techniques. Furthermore, we discuss advantages and disadvantages with the two analysis approaches and the output data they provide. XPS reference data from the bacterial strain are provided, and we propose that planktonic cells of this strain (DSM 50090) are used as a reference material for surface chemical analysis of bacterial systems.
KW - P. Fluorescens
KW - Cryo XPS
KW - NAP-XPS
KW - DSM 5009
PY - 2021
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-525640
DO - https://doi.org/10.3389/fchem.2021.666161
VL - 9
SP - Article 666161
PB - Frontiers
CY - Switzerland
AN - OPUS4-52564
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Dopffel, N.
A1 - An Stepec, Biwen Annie
A1 - de Rezende, J.
A1 - Machado de Sousa, D.
A1 - Koerdt, Andrea
T1 - Microbiology of Underground Hydrogen Storage
N2 - Climate change is becoming one of the greatest challenges facing our society, particularly due to the continued use of fossil fuels. The steadily increasing demand for energy and the continuously growing world population will further intensify these challenges. The development of renewable energies is therefore of central importance. The 2020 EU Energy Roadmap aims to increase the share of renewable energies (gross energy consumption) to 55% by 2050.
Hydrogen (H2) has the highest potential to become the primary renewable energy source. It is envisioned that by 2050 up to 24% of the total energy demand of Europe is to be ensured by H2. However, a decisive disadvantage of the climate friendly alternatives is the massive containment demand, which needs to be highly secure, cost efficient and easily extractable.
Underground geological formations (UGF) represent a seemingly optimal alternative to meet the rapidly increasing storage demand. In this context, many studies are currently underway to determine the feasibility and risks of UGF. However, little or no consideration is being given to microbiology. Therefore, in this Research Topic we will focus on achieving a greater understanding of the impact microorganisms exert on UGF, with a particular emphasis on interdisciplinary studies.
As many subsurface microbial communities can use H2 as an electron donor, production of seemingly undesirable metabolic byproducts, such as hydrogen sulfide, methane, and acids, are also to be expected. However, the rate of the H2 conversion by the microorganisms, how their metabolic activities impact the UGF on a short-term and long-term scale, the extent of damages microorganisms exert on the infrastructure, or potential use of microorganisms to enhance UGF are just a few questions that require urgent research to assess the role of microorganisms in this new anthropogenic use of the subsurface environment. These and many questions can be addressed in this article collection. In particular, understanding microbial community changes and activity rates will help assess operational and environmental risks, develop mitigation strategies and provide new insights on life under extreme conditions (i.e., pressure, salinity).
In this Research Topic, the editorial team particularly welcomes Original Research, Hypothesis and Theory, Method, and Review manuscripts that deal with the latest advances in microbiology in formations that are planned or currently prepared for hydrogen storage, from both fundamental and practical points of view. The ultimate objective is to promote a deeper understanding into the sustainability of UGF and generate interdisciplinary research involving microbiologists, reservoir engineers, geologists, chemists, physicists.
The topics of interest include, but are not limited to:
• Microbial diversity in different underground hydrogen storage sites or formations currently being considered for hydrogen storage
• Mechanism and impact of microbial growth under high H2 pressure
• Potential role of microorganisms in the short-term and long-term storage of hydrogen
• Potential influences of microorganisms on the hydrogen storage infrastructure systems, e.g., microbiologically influenced corrosion, biofilm growth
• Hydrogen-solid-microorganism interactions, including the influence of microbial growth on UGF geological parameters
• Mechanism and modelling of microbial impact on hydrogen storage
UGF relevant for this Research Topic include porous media, salt caverns, deep aquifers, hard rock caverns and depleted oil/gas reservoirs.
KW - Biodeterioration and biodegradation
KW - Geology
KW - Anaerobic pathways
KW - Microbial simulation,
KW - Hydrogen storage
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-579042
DO - https://doi.org/10.3389/fenrg.2023.1242619
SN - 2296-598X
VL - 11
SP - 1
EP - 3
PB - Frontiers
CY - Frontiers in Energy Research
AN - OPUS4-57904
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - An, Biwen Annie
A1 - Deland, Eric
A1 - Kleinbub, Sherin
A1 - Koerdt, Andrea
T1 - Standardization of MIC laboratory testing: with a special focus on corrosive methanogens
N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process involving a complex group of microorganisms, including sulfate-reducing bacteria and methanogens. Standard laboratory MIC testing using static serum bottle enrichments is an easy but limited method, offering poor resolution on the biomineralization process of corrosion products. An example of this is the presumed corrosion product siderite by corrosive methanogens (Mi-MIC). Previous publications reported siderite was the sole corrosion product of M. maripaludis using metal coupons incubated under stationary conditions.
However, the formation of siderite is closely related to the surrounding environmental conditions, i.e. pH, CO2 concentration, flow and temperature. Thus, siderite as the sole corrosion product of Mi-MIC remain inconclusive and questionable. To study Mi-MIC effectively, a novel versatile multiport flow-column corrosion monitoring system (MFC) was developed. MFC allows sectional corrosion rate determination under flow conditions using different types of material, inoculum and packing material. MFC offers great flexibility, ease of operation and accurate corrosion measurements that can be combined with many other techniques. Using MFC, we studied multiple strains of methanogens and compared it with sulfate-reducing bacteria under neutral and low pH conditions. It was revealed by MFC that corrosive methanogens have equally high corrosion potential as sulfate-reducing bacteria. Additionally, siderite is not the dominant nor sole corrosion product of Mi-MIC. Thus, effective corrosion monitoring and establishing standard laboratory practices, i.e. incorporating MFC as part of regular testing process, will provide deeper understanding of MIC. This will allow further microbial electrophysiology understandings, contributing to effective mitigation strategy development.
T2 - EUROPEAN MIC NETWORK WEBINAR
CY - Online meeting
DA - 19.05.2020
KW - MIC
KW - Methanogen
KW - FIB/SEM
KW - Corrosion products
KW - Microbiologically influenced corrosion
KW - Flow Model
KW - Modelling
KW - Korrosion
PY - 2020
AN - OPUS4-51554
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Schraut, Katharina
A1 - Adam, Christian
A1 - Adamczyk, Burkart
A1 - Simon, Sebastian
A1 - von Werder, Julia
A1 - Meng, Birgit
A1 - Stephan, Dietmar
T1 - Production of an alite-rich material from reduced basic oxygen furnace slags
N2 - Basic oxygen furnace slag (BOFS) is a by-product of steelmaking of which about 10.4 Mt are produced annually in the EU. BOFS is mostly used in road construction, earthwork and hydraulic engineering. However, in this use, the iron bound in BOFS is lost and the opportunity to produce higher value products from BOFS is forgone.
In recent decades, many researchers have investigated the production of both Portland cement clinker and crude iron from BOFS via a thermochemical reductive treatment. The reductive treatment of liquid BOFS causes a reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density and can be recovered. An advantage of this process is that simultaneously the chemical composition of the reduced BOFS is adapted to that of Portland cement clinker and the hydraulic reactive mineral alite (Ca3SiO5) is formed.
In this study, German BOFS was reduced in a small-scale electric arc furnace and a low-iron mineral product rich in alite was produced. Despite a chemical and mineralogical composition similar to that of Portland cement clinker, the reduced BOFS produced less heat of hydration, and its reaction was delayed compared to Portland cement. However, adding gypsum accelerated the hydration rate of the reduced BOFS.
Further research to improve the hydraulic properties of the reduced BOFS is essential. If successful, the production of a hydraulic material and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry.
T2 - GeoBerlin 2023
CY - Berlin, Germany
DA - 04.09.2023
KW - BOFS
KW - Alite
KW - Hydraulic reactivity
PY - 2023
AN - OPUS4-58206
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Souza Filho, I.
A1 - Adam, Christian
T1 - Fundamentals of the hydrogen plasma reduction of iron ores
N2 - Hydrogen plasma treatment of iron ores or iron oxide containing wastes can be an efficient option to produce green iron e.g. for steel production. This way iron oxide is reduced to metallic iron in the liquid form by the highly reactive species that are formed in a hydrogen plasma. Hydrogen plasma can be used at the same time to remove undesired gangue elements. The presentation shows the experimental setup, shows first results of iron ore reduction by hydrogen plasma and gives an outlook for industrial application of the technology.
T2 - European Academic Symposium on EAF steelmaking (EASES 2023)
CY - Oulu, Finland
DA - 05.06.2023
KW - Hydrogen
KW - Plasma
KW - Reduction
PY - 2023
AN - OPUS4-57626
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Jovičević-Klug, Matic
A1 - Souza Filho, Isnaldi R.
A1 - Springer, Hauke
A1 - Adam, Christian
A1 - Raabe, Dierk
T1 - Green steel from red mud through climate-neutral hydrogen plasma reduction
N2 - AbstractRed mud is the waste of bauxite refinement into alumina, the feedstock for aluminium production1. With about 180 million tonnes produced per year1, red mud has amassed to one of the largest environmentally hazardous waste products, with the staggering amount of 4 billion tonnes accumulated on a global scale1. Here we present how this red mud can be turned into valuable and sustainable feedstock for ironmaking using fossil-free hydrogen-plasma-based reduction, thus mitigating a part of the steel-related carbon dioxide emissions by making it available for the production of several hundred million tonnes of green steel. The process proceeds through rapid liquid-state reduction, chemical partitioning, as well as density-driven and viscosity-driven separation between metal and oxides. We show the underlying chemical reactions, pH-neutralization processes and phase transformations during this surprisingly simple and fast reduction method. The approach establishes a sustainable toxic-waste treatment from aluminium production through using red mud as feedstock to mitigate greenhouse gas emissions from steelmaking.
KW - Multidisciplinary
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594424
DO - https://doi.org/10.1038/s41586-023-06901-z
SN - 0028-0836
VL - 625
IS - 7996
SP - 703
EP - 709
PB - Springer Science and Business Media LLC
AN - OPUS4-59442
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Hamann, Christopher
A1 - Piehl, Patrick
A1 - Weingart, Eric
A1 - Stolle, Dirk
A1 - Al-Sabbagh, Dominik
A1 - Ostermann, Markus
A1 - Auer, Gerhard
A1 - Adam, Christian
T1 - Selective removal of zinc and lead from electric arc furnace dust by chlorination–evaporation reactions
N2 - Re-melting of scrap in an electric arc furnace (EAF) results in the accumulation of filter dust from off-gas treatment that predominantly consists of iron and zinc oxides. Filter dust is classified as hazardous waste due to its high contents of potentially toxic or ecotoxic elements such as Pb, Cr, Cd, and As. A promising processing route for this waste is selective chlorination, in which the non-ferrous metal oxides are chlorinated and selectively evaporated in form of their respective chlorides from the remaining solids via the process gas flow. Here, we investigate stepwise thermochemical treatment of EAF dust with either waste iron(II) chloride solution or hydrochloric acid at 650, 800, and 1100 ◦C. The Zn and Pb contents of the thermochemically processed EAF dust could be lowered from 29.9% and 1.63% to 0.09% and 0.004%, respectively. Stepwise heating allowed high separation between zinc chloride at the 650 ◦C step and sodium-, potassium-, and lead-containing chlorides at higher temperatures. Furthermore, the lab-scale results were transferred to the use of an experimental rotary kiln highlighting the possibilities of upscaling the presented process. Selective chlorination of EAF dust with liquid chlorine donors is, therefore, suggested as a potential recycling method for Zn-enriched steelworks dusts.
KW - Electric arc furnace dust
KW - Zinc
KW - Selective Chlorination
KW - Hazardous waste
KW - Resource Recovery
PY - 2024
DO - https://doi.org/10.1016/j.jhazmat.2023.133421
SN - 0304-3894
VL - 465
SP - 1
EP - 13
PB - Elsevier
AN - OPUS4-59345
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - RPRT
A1 - An, Biwen Annie
A1 - Shen, Y.
A1 - Voordouw, J.
A1 - Voordouw, G.
ED - Dumas, C.
T1 - Halophilic Methylotrophic Methanogens May Contribute to the High Ammonium Concentrations Found in Shale Oil and Shale Gas Reservoirs
N2 - Flow-back and produced waters from shale gas and shale oil fields contain high ammonium, which can be formed by methanogenic degradation of methylamines into methane and ammonium. Methylamines are added to fracturing fluid to prevent clay swelling or can originate from metabolism of the osmolyte triglycinebetaine (GB).
We analyzed field samples from a shale gas reservoir in the Duvernay Formation and from a shale oil reservoir in the Bakken formation in Canada to determine the origin of high ammonium. Fresh waters used to make fracturing fluid, early flow-back waters, and late flow back waters from the shale gas reservoir had increasing salinity of 0.01, 0.58, and 2.66 Meq of NaCl, respectively. Microbial community analyses reflected this fresh water to saline transition with halophilic taxa including Halomonas, Halanaerobium, and Methanohalophilus being increasingly present. Early and late flow-back waters had high ammonium concentrations of 32 and 15 mM, respectively.
Such high concentrations had also been found in the Bakken produced waters.
Enrichment cultures of Bakken produced waters in medium containing mono, di-, or trimethylamine, or triglycinebetaine (GB) converted these substrates into ammonium (up to 20 mM) and methane. The methylotrophic methanogen Methanohalophilus, which uses methylamines for its energy metabolism and uses GB as an osmolyte, was a dominant community member in these enrichments. Halanaerobium was also a dominant community member that metabolizes GB into trimethylamine, which is then metabolized further by Methanohalophilus. However, the micromolar concentrations of GB measured in shale reservoirs make them an unlikely source for the 1,000-fold higher ammonium concentrations in flow-back waters. This ammonium either originates directly from the reservoir or is formed from methylamines, which originate from the reservoir, or are added during the hydraulic fracturing process. These methylamines are then converted into ammonium and methane by halophilic methylotrophic methanogens, such as Methanohalophilus, present in flow-back waters.
KW - Methanogen
KW - Oil and gas industry
KW - Shale
KW - Halophile
KW - Corrosion
PY - 2019
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-474982
UR - https://www.frontiersin.org/articles/10.3389/fenrg.2019.00023/full
DO - https://doi.org/10.3389/fenrg.2019.00023
VL - 7
SP - Article 23, 1
EP - 13
PB - Frontiers Media
CY - Frontiers in Energy Research
AN - OPUS4-47498
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Machado Ferreira de Araujo, F.
A1 - Duarte-Ruiz, D.
A1 - Saßnick, H.-D.
A1 - Gentzmann, Marie C.
A1 - Huthwelker, T.
A1 - Cocchi, C.
T1 - Electronic Structure and Core Spectroscopy of Scandium Fluoride Polymorphs
N2 - Microscopic knowledge of the structural, energetic, and electronic properties of scandium fluoride is still incomplete despite the relevance of this material as an intermediate for the manufacturing of Al−Sc alloys. In a work based on first-principles calculations and X-ray spectroscopy, we assess the stability and electronic structure of six computationally predicted ScF3 polymorphs, two of which correspond to experimentally resolved single-crystal phases. In the theoretical analysis based on density functional theory (DFT), we identify similarities among the polymorphs based on their formation energies, chargedensity distribution, and electronic properties (band gaps and density of states). We find striking analogies between the results obtained for the ow- and high-temperature phases of the material, indirectly confirming that the transition occurring between them mainly consists of a rigid rotation of the lattice. With this knowledge, we examine the X-ray absorption spectra from the Sc and F K-edge contrasting firstprinciples results obtained from the solution of the Bethe−Salpeter equation on top of all-electron DFT with high-energy-resolution fluorescence detection measurements. Analysis of the computational results sheds light on the electronic origin of the absorption maxima and provides information on the prominent excitonic effects that characterize all spectra. A comparison with measurements confirms that the sample is mainly composed of the high- and low-temperature polymorphs of ScF3. However, some fine details in the experimental results suggest that the probed powder sample may contain defects and/or residual traces of metastable polymorphs.
KW - Scandium
KW - X-ray spectroscopy
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-570727
DO - https://doi.org/10.1021/acs.inorgchem.2c04357
SN - 0020-1669
VL - 62
IS - 10
SP - 4238
EP - 4247
PB - ACS Publications
CY - Washington DC
AN - OPUS4-57072
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
ED - Schraut, Katharina
ED - Adamczyk, Burkart
ED - Adam, Christian
ED - Stephan, D.
ED - Simon, Sebastian
ED - von Werder, Julia
ED - Meng, Birgit
T1 - Production of a hydraulic material from post treated steelmaking slags
N2 - Steelmaking slag is a by-product of steel production, of which 4.5 Mt were produced in 2020 in Germany alone. It is mainly used in road construction, earthwork and hydraulic engineering. A smaller part is returned to the metallurgical cycle, used as fertiliser or landfilled.
With this use, iron oxides still contained in steelmaking slag are lost. In addition, the possibility of producing higher-grade products from steelmaking slag is foregone. In recent decades, many researchers have investigated the production of Portland cement clinker and crude iron from basic oxygen furnace slags (BOFS) via a reductive treatment. Carbothermal treatment of liquid BOFS causes a reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density. Simultaneously, the chemical composition of the reduced slag is adapted to that of Portland cement clinker.
In this study, German BOFS was reduced in a small-scale electric arc furnace using petrol coke as a reducing agent. The resulting low-iron mineral product has a similar chemical composition to Portland cement clinker and was rich in the tricalcium silicate solid solution alite (Ca3SiO5). Based on its chemical and mineralogical composition, similar to that of Portland cement clinker, the reduced BOFS has the potential to react comparably. In our study, the reduced BOFS produced less hydration heat than OPC, and its hydraulic reaction was delayed. However, adding gypsum has shown to accelerate the hydration rate of the reduced BOFS compared to that known from the calcium silicates of Portland cement clinker.
Further research to improve the hydraulic properties of the reduced slag is essential. If successful, producing a hydraulic binder and crude iron from BOFS has economic and ecological benefits for both the cement and steel industries.
T2 - The 16th International Congress on the Chemistry of Cement 2023 (ICCC2023)
CY - Bangkok, Thailand
DA - 18.09.2023
KW - Steelmaking slag
KW - Alite
KW - Clinker substitute
KW - Hydraulic reactivity
PY - 2023
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-590522
UR - https://www.iccc-online.org/archive/
SP - 432
EP - 436
CY - Bangkok
AN - OPUS4-59052
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Schraut, Katharina
A1 - Adamczyk, Burkart
A1 - Simon, Sebastian
A1 - von Werder, Julia
A1 - Meng, Birgit
A1 - Stephan, Dietmar
A1 - Adam, Christian
T1 - Formation and hydraulic reactivity of an alite rich material from post treated basic oxygen furnace slag
N2 - Basic oxygen furnace slag (BOFS) is a by-product of steelmaking of which about 10.4 Mt are produced annually in the EU. BOFS is mostly used in road construction, earthwork and hydraulic engineering. However, in this use, the iron bound in BOFS is lost and the opportunity to produce higher value products from BOFS is forgone.
In recent decades, many researchers have investigated a thermochemical process to reduce iron oxides to metallic iron in molten BOFS. The metallic iron formed separates from the reduced slag due to its higher density and can be recovered. An advantage of this process is that simultaneously the chemical composition of the reduced slag is adapted to that of the Portland cement clinker and the hydraulic reactive mineral alite is formed.
In this study, BOFS was reduced in a small-scale electric arc furnace using petrol coke as reducing agent, and the hydraulic properties of the reduced, low-iron BOFS were investigated. Despite a chemical and mineralogical composition similar to that of Portland cement clinker, the reduced BOFS produced less heat of hydration, and its reaction was delayed compared to Portland cement. However, the addition of gypsum, as is also done in cement production from Portland cement clinker, has been found to accelerate the hydration rate of reduced BOFS.
Further research to improve the hydraulic properties of the reduced slag is essential. If successful, the production of a hydraulic binder and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry.
T2 - GeoMin Köln 2022
CY - Cologne, Germany
DA - 11.09.2022
KW - BOFS
KW - Portland Cement
KW - Hydraulic reactivity
PY - 2022
AN - OPUS4-56080
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Koerdt, Andrea
A1 - An, Biwen Annie
A1 - Kleinbub, Sherin
T1 - Microbial corrosion coupled to methanogenesis by strains from different environments
N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms, either chemically (formation of hydrogen sulfide) or electrically (direct electron uptake). Methanogenetic Archaea are also known to be involved in iron corrosion, forming a multi-species biofilm on corroding metallic structures. However, mechanistic details and kinetics of the overall process in methanogen-induced MIC are poorly understood.
T2 - Beirat Material
CY - Berlin, Germany
DA - 26.04.2018
KW - Corrosion
KW - Methanogens
KW - Archaea
KW - Implants
KW - Biofilm
PY - 2018
AN - OPUS4-45112
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Knisz, J.
A1 - Eckert, R.
A1 - Gieg, L.
A1 - Koerdt, Andrea
A1 - Lee, J.
A1 - Silva, E.
A1 - Skovhus, T. L.
A1 - An Stepec, Biwen Annie
A1 - Wade, S. A.
T1 - Microbiologically Influenced Corrosion - More than just Microorganisms
N2 - Microbiologically influenced corrosion (MIC) is a phenomenon of increasing concern which affects various materials and sectors of society. MIC describes the effects, often negative, that a material can experience due to the presence of microorganisms. Unfortunately, although several research groups and industrial actors worldwide have already addressed MIC, discussions are fragmented, while information sharing and willingness to reach out to other disciplines is limited. A truly interdisciplinary approach, that would be logical for this material/biology/chemistry-related challenge, is rarely taken. In this review we highlight critical non-biological aspects of MIC that can sometimes be overlooked by microbiologists working on MIC but are highly relevant for an overall understanding of this phenomenon. Here, we identify gaps, methods and approaches to help solve MIC related challenges, with an emphasis on the MIC of metals. We also discuss the application of existing tools and approaches for managing MIC and propose ideas to promote an improved understanding of MIC. Furthermore, we highlight areas where the insights and expertise of microbiologists are needed to help progress this field.
KW - MIC
KW - Biodeterioration
KW - Biocorrosion
KW - Interdisciplinarity
KW - Multiple lines of evidence
PY - 2023
DO - https://doi.org/10.1093/femsre/fuad041
SN - 0168-6445
VL - 47
IS - 5
SP - 1
EP - 70
PB - FEMS Microbiology Reviews
AN - OPUS4-58066
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Vogel, Christian
A1 - Hermann, P.
A1 - Kästner, B.
A1 - Adamczyk, Burkart
A1 - Hoehl, A.
A1 - Ulm, G.
A1 - Adam, Christian
T1 - Air and chlorine gas corrosion of different silicon carbides analyzed by nano-Fourier-transform infrared (nano-FTIR) spectroscopy
N2 - The present study shows the potential of high-resolution imaging and nano-Fourier-transform infrared (nano-FTIR) spectroscopy for corrosion science. The protective oxidation layers of different chlorine-gas treated silicon
carbides (SiCs) were characterized with these techniques. A nitrified SiC showed the highest resistant strength against chlorine corrosion at 1000 °C compared to the other SiCs. Nano-FTIR spectroscopy with a lateral resolution below 40 nm detected differences in the crystallinity of the bulk-SiC and in the transitional region to the protective layer. Furthermore, high-resolution imaging provides deep insight in the interfacial layer between bulk-SiC and the protective oxidation layer on sub-micrometer scale.
KW - Nano-Fourier-transform infrared spectroscopy
KW - Scattering-type scanning near-field optical microscopy (s-SNOM)
KW - Synchrotron radiation
KW - Corrosion
KW - Silicon carbide
KW - Chlorine
PY - 2018
DO - https://doi.org/10.1016/j.corsci.2017.12.002
SN - 0010-938X
VL - 131
SP - 324
EP - 329
PB - Elsevier
AN - OPUS4-43648
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Kittner, Maria
A1 - Altmann, Korinna
A1 - Hamann, Sven
A1 - Weyer, Rüdiger
A1 - Kalbe, Ute
T1 - Assessment of Microplastic Emissions from Artificial Turf Sports Pitches
N2 - Following the recommendation of the European Chemicals Agency, on 25 September 2023 the European Commission passed a comprehensive new regulation to reduce emissions of microplastics (MP) into the environment, which includes the sale and use of intentionally added MP.1,2 This also applies to the application of synthetic rubber granulate infill in artificial turf systems and will ultimately have an impact on recreational sports. In Germany, rubber granulate made of ethylene-propylene-diene-monomer rubber (EPDM) is currently predominantly used. So far, there is no sufficient database for estimating MP emissions from artificial turf pitches into the environment and thus their relevance as a source of MP pollution.3 This topic is controversially discussed due to the complexity of sampling and analytics. To close this research gap, this project has the goal to determine mass balances for the emissions of MP from artificial turf pitches to allow an estimation of the amount of MP released per artificial turf pitch and year.
Within this study, MP emissions of three artificial turf scenarios at different time states (unaged, artificially aged and real-time aged) are compared: the past (old turf: fossil based, synthetic infill), present (most commonly installed in Europe: fossil based, EPDM infill), and the future (turf with recycled gras fibres, no synthetic infill). To simulate the outdoor weathering during the lifespan of an artificial turf of approx. 15 years, brand-new artificial turf and EPDM rubber granulate were accelerated aged by means of UV weathering and mechanical stress. Potential MP emissions into surface and groundwater are simulated by lysimeter and shake experiments. MP mass contents are subsequently determined by Thermal Extraction Desorption Gas Chromatography/Mass Spectrometry. Using special microfilter crucibles allows the estimation of the particle sizes of the emitted MP, which is a fundamental requirement for an assessment of potential health hazards for humans.
T2 - SETAC 2024
CY - Seville, Spain
DA - 05.05.2024
KW - Mikroplastik
KW - TED-GC/MS
KW - Lysimeter
KW - PAK
KW - Schwermetalle
PY - 2024
AN - OPUS4-60014
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Schraut, Katharina
A1 - Adamczyk, Burkart
A1 - Adam, Christian
T1 - Reductive treatment of steel making slags to produce a hydraulic binder and crude iron
N2 - Steelmaking slags are a by-product of steel production, that are currently used primarily in road construction, earthwork, and hydraulic engineering. In this use, the iron bound in the steelmaking slags (< 30 wt.%) is lost.
Recovery of iron from steelmaking slags is possible by thermochemical reductive treatment. The reductive treatment of liquid steelmaking slags causes iron oxides to be reduced to metallic iron, which separates from the mineral phase due to its higher density. The chemical composition of the mineral phase is thus adapted to that of the Portland cement clinker and the mineral alite, the most important component of Portland cement, is formed. This way, crude iron can be recovered, and at the same time a hydraulic binder can be produced.
This process, however, is uneconomical due to the high temperatures required (~1800 °C). In the current project, the process is to be adapted so that the reduction of liquid steelmaking slag can be carried out at ~1600 °C. The chemical composition is to be modified in such a way that the melting temperature of the slags as well as their viscosity are in a technically suitable range and still a product with good cementitious properties is obtained.
T2 - LithiumDays
CY - Online meeting
DA - 06.12.2021
KW - BOFS
KW - Portland Cement
KW - Hydraulic reactivity
PY - 2021
AN - OPUS4-56081
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Dombinov, V.
A1 - Herzel, Hannes
A1 - Meiller, M.
A1 - Müller, F.
A1 - Willbold, S.
A1 - Zang, J. W.
A1 - da Fonseca-Zang, W. A.
A1 - Adam, Christian
A1 - Klose, H.
A1 - Poorter, H.
A1 - Jablonowski, N. D.
A1 - Schrey, S. D.
T1 - Sugarcane bagasse ash as fertilizer for soybeans: Effects of added residues on ash composition, mineralogy, phosphorus extractability and plant availability
N2 - Sugarcane bagasse is commonly combusted to generate energy. Unfortunately, recycling strategies rarely consider the resulting ash as a potential fertilizer. To evaluate this recycling strategy for a sustainable circular economy, we characterized bagasse ash as a fertilizer and measured the effects of co-gasification and co-combustion of bagasse with either chicken manure or sewage sludge: on the phosphorus (P) mass fraction, P-extractability, and mineral P phases. Furthermore, we investigated the ashes as fertilizer for soybeans under greenhouse conditions. All methods in combination are reliable indicators helping to assess and predict P availability from ashes to soybeans. The fertilizer efficiency of pure bagasse ash increased with the ash amount supplied to the substrate. Nevertheless, it was not as effective as fertilization with triple-superphosphate and K2SO4, which we attributed to lower P availability. Co-gasification and co-combustion increased the P mass fraction in all bagasse-based ashes, but its extractability and availability to soybeans increased only when co-processed with chicken manure, because it enabled the formation of readily available Ca-alkali phosphates. Therefore, we recommend co-combusting biomass with alkali-rich residues to increase the availability of P from the ash to plants.
KW - Combustion and gasification
KW - Phosphate extractability and availability
KW - X-ray diffraction (XRD)
PY - 2022
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-567632
DO - https://doi.org/10.3389/fpls.2022.1041924
SN - 1664-462X
VL - 13
SP - 1
EP - 13
PB - Frontiers Media
CY - Lausanne
AN - OPUS4-56763
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Taube, Mareike Carolin
A1 - Adam, Christian
A1 - Adamczyk, Burkart
A1 - Schulenburg, F.
A1 - Bartmann, U.
A1 - Beckmann, T.
A1 - Michalik, K.
A1 - Reuter, M.
A1 - Stelter, M.
T1 - Optimisation of a Pyrometallurgical Niobium and Tantalum Recyling Process with on-line-LIBS
N2 - Tantalum and niobium are essential for the development of electronics towards a more and more compact design, but without reducing their performance today. Especially in smart phones and tablets, tantalum and niobium capacitors with high charge densities have already become almost indispensable. However, tantalum as a critical raw material is still a problem for the sustainable production of electronics. Due to this fact, the existence of efficient recycling processes especially in Europe is becoming even more important nowadays.
The Bundesanstalt für Materialforschung und -prüfung (BAM) is currently working on the optimisation of an existing pyrometallurgical tantalum recycling process. Optimisation of this industrial process is carried out in a small-scale electric arc furnace (480 kVA, capacity approx. 150 kg/h) at BAM using a new and innovative equipment for on-line analysis of high temperature processes.
The aim of this project is to identify the best timing for an optimum slag tapping, when the slag is lower than minimum targeted tantalum concentration. Hence, LIBS (Laser induced breakdown spectroscopy) is used to identify the chemical composition of the slag layer and during slag tapping. The on-line-LIBS prototype of BAM enables an in-situ measurement of the element distribution in the melt after calibration on the slag system.
First results of this joint research project will be presented including LIBS-measurements and thermodynamic and kinetic aspects of the process.
T2 - European Mineral Processing & Recycling Congress (EMPRC 2018)
CY - Essen, Germany
DA - 25.06.2018
KW - Laser-induced breakdown spectroscopy
KW - On-line analysis
KW - Tantalum
KW - Niobium
KW - Pyrometallurgy
PY - 2018
SN - 978-3-940276-84-1
SP - 347
EP - 362
PB - GDMB Verlag GmbH
CY - Clausthal-Zellerfeld
AN - OPUS4-47040
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Taube, Mareike Carolin
A1 - Adam, Christian
A1 - Adamczyk, Burkart
A1 - Schulenburg, F.
A1 - Bartmann, U.
A1 - Beckmann, T.
A1 - Michalik, K.
A1 - Reuter, M.
A1 - Stelter, M.
T1 - Optimisation of a Pyrometallurgical Niobium and Tantalum Recyling Process with on-line-LIBS
N2 - Tantalum and niobium are essential for the development of electronics towards a more and more compact design, but without reducing their performance today. Especially in smart phones and tablets, tantalum and niobium capacitors with high charge densities have already become almost indispensable. However, tantalum as a critical raw material is still a problem for the sustainable production of electronics. Due to this fact, the existence of efficient recycling processes especially in Europe is becoming even more important nowadays.
The Bundesanstalt für Materialforschung und -prüfung (BAM) is currently working on the optimisation of an existing pyrometallurgical tantalum recycling process. Optimisation of this industrial process is carried out in a small-scale electric arc furnace (480 kVA, capacity approx. 150 kg/h) at BAM using a new and innovative equipment for on-line analysis of high temperature processes.
The aim of this project is to identify the best timing for an optimum slag tapping, when the slag is lower than minimum targeted tantalum concentration. Hence, LIBS (Laser induced breakdown spectroscopy) is used to identify the chemical composition of the slag layer and during slag tapping. The on-line-LIBS prototype of BAM enables an in-situ measurement of the element distribution in the melt after calibration on the slag system.
First results of this joint research project will be presented including on-line-LIBS-measurements and thermodynamic and kinetic aspects of the process.
T2 - European Mineral Processing & Recycling Congress (EMPRC 2018)
CY - Essen, Germany
DA - 25.06.2018
KW - Laser-induced breakdown spectroscopy
KW - Process control
KW - Tantalum
KW - In-situ analysis
KW - Pyrometallurgy
PY - 2018
AN - OPUS4-45614
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Dinter, Adelina-Elisa
A1 - An, Biwen Annie
A1 - Wurzler, Nina
A1 - Özcan Sandikcioglu, Özlem
A1 - Koerdt, Andrea
A1 - Meermann, Björn
T1 - Development of a MIC single archaea-ICP-ToF-MS-method for analysis of various elements in solid steel samples
N2 - ICP-ToF (Flugzeitanalysator, engl. time of flight)-MS ermöglicht den Multielement Fingerabdruck einzelner Zellen (single cell) zu analysieren. Die single cell-ICP-ToF-MS kommt bei dem vorgestellten Poster bei der Analyse von Archaeen, die an mikrobiell beeinflusster Korrosion (engl. microbiologically influenced corrosion, MIC) von Stahl eine Rolle spielen, zum Einsatz. Mittels sc-ICP-ToF-MS wird die mögliche Aufnahme von einzelnen Elementen aus dem jeweiligen Stahl untersucht – die erhaltenen Informationen fließen zukünftig in die Aufklärung zugrunde liegender Mechanismen sowie Entwicklung möglicher Materialschutzkonzepte ein. Die Arbeiten Verknüpfen moderne Methoden der Analytical Sciences mit Materialien.
T2 - Tag der Chemie 2021
CY - Online meeting
DA - 06.07.2021
KW - SC-ICP-ToF-MS
KW - Single cell analysis
KW - Microbiologically influenced corrosion
KW - Archaea
PY - 2021
AN - OPUS4-52941
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - JOUR
A1 - Erdmann, Eileen A.
A1 - Brandhorst, Antonia K. M.
A1 - Gorbushina, Anna A.
A1 - Schumacher, Julia
T1 - The Tet‑on system for controllable gene expression in the rock‑inhabiting black fungus Knufia petricola
N2 - Knufia petricola is a black fungus that colonizes sun-exposed surfaces as extreme and oligotrophic environments. As ecologically important heterotrophs and biofilm-formers on human-made surfaces, black fungi form one of the most resistant groups of biodeteriorating organisms. Due to its moderate growth rate in axenic culture and available protocols for its transformation and CRISPR/Cas9-mediated genome editing, K. petricola is used for studying the morpho-physiological adaptations shared by extremophilic and extremotolerant black fungi. In this study, the bacteria-derived tetracycline (TET)-dependent promoter (Tet-on) system was implemented to enable controllable gene expression in K. petricola. The functionality i.e., the dose-dependent inducibility of TET-regulated constructs was investigated by using GFP fluorescence, pigment synthesis(melanin and carotenoids) and restored uracil prototrophy as reporters. The newly generated cloning vectors containing the Tet-on construct, and the validated sites in the K. petricola genome for color-selectable or neutral insertion of expression constructs complete the reverse genetics toolbox. One or multiple genes can be expressed on demand from different genomic loci or from a single construct by using 2A self-cleaving peptides, e.g., for localizing proteins and protein complexes in the K. petricola cell or for using K. petricola as host for the expression of heterologous genes.
KW - Microcolonial fungi
KW - Inducible promoter
KW - Bimolecular fluorescence complementation
KW - 2A peptide
KW - CRISPR/ Cas9-mediated genome editing
PY - 2024
UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-607672
DO - https://doi.org/10.1007/s00792-024-01354-2
VL - 28
IS - 38
SP - 1
EP - 13
PB - Springer Nature
AN - OPUS4-60767
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -
TY - CONF
A1 - Gorbushina, Anna A.
A1 - Erdmann, Eileen A.
A1 - Gerrits, Ruben
A1 - Schumacher, Julia
T1 - From rocks to riches: Knufia petricola as model and expression platform
N2 - Black fungi belong to different classes of Ascomycota but evolved similar morpho-physiological adaptations such as yeast-like growth and constitutive melanin formation to colonize extreme competition-free environments. They are ubiquitously found on air-exposed surfaces, from ancient marble monuments to modern solar panels. The rock inhabitant Knufia petricola was chosen to become a model for these extremotolerant black fungi. Plasmid-based and ribonucleoprotein-based CRISPR/Cas9 techniques were introduced to precisely introduce one to multiple double strand breaks into the DNA to modify, replace or add sequences to the genome either using the available selection marker systems (hygR, natR, genR, baR, suR) or by marker-free approaches. Multiplexing is very efficient, allowing for four or more simultaneous genome editing events. The newly generated cloning vectors containing the Tet on construct for doxycycline-controlled gene expression, and the validated sites in the K. petricola genome for color-selectable (pks1, phs1, ade2) or neutral insertion (igr1 to 5) of expression constructs complete the reverse genetics toolbox. One or multiple endogenous or heterologous genes can be expressed on demand from different genomic loci or from a single construct by using 2A self-cleaving peptides. We thus can express genes from synthetic clusters in a non-pigmented background (Δpks1/Δphs1). The fact that K. petricola only produces few secondary metabolites (DHN melanin, carotenoids, mycosporines and a siderophore) and plant cell-wall degrading enzymes but is capable to take the burden of acetyl-CoA-consuming metabolism and protein secretion renders K. petricola a promising host for the expression of heterologous genes encoding high-end secondary metabolites and enzymes.
T2 - 12th International Mycological Congress (IMC12)
CY - Maastricht, Netherlands
DA - 11.08.2024
KW - Fungus
KW - Genetic engineering
KW - Heterologous gene expression
KW - Cell factory
PY - 2024
AN - OPUS4-60838
LA - eng
AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany
ER -