TY - CONF A1 - Kittner, Maria T1 - Contaminant Emissions from Artificial Turf Sports Pitches - Simultaneous sampling for Microplastics, PAH and Heavy Metals N2 - In September 2023, the European Commission introduced a new regulation to reduce microplastic (MP) emissions into the environment, including the sale and use of intentionally added (large) MP < 5 mm (ISO/TR 21960: 2020). This explicitly applies to the use of synthetic rubber granulate infill in artificial turf installations, which are complex multi-component systems consisting of multiple synthetic polymers (Fig. 1). In addition, abrasions of synthetic grass fibres and other turf components are also considered as MP sources. Although this has a major impact on public recreational sports, there is so far no sufficient data to estimate the MP emissions from artificial turf sports pitches into the environment and thus their relevance as a source of MP pollution. To close this gap, this study compared environmental contaminant emissions of three artificial turf scenarios at different ageing states (unaged, artificially and real-time aged): the past (old turf: fossil based, synthetic infill), present (most commonly installed in Germany: fossil based, EPDM infill) and future (turf with recycled grass fibres, no synthetic infill). Accelerated ageing by UV weathering and mechanical stress was carried out to simulate the outdoor weathering during the lifespan of approx. 15 years. MP emissions and released environmentally relevant contaminants posing a risk to the groundwater were simultaneously sampled using the newly developed Microplastic Eluate Lysimeter manufactured at BAM (Fig. 2). MP contents were analysed using smart microfilter crucibles (mesh size: 5 μm) with subsequent MP detection by TED-GC/MS. Additionally, concentrations of polycyclic aromatic hydrocarbons were determined using GC/MS and heavy metals using ICP-AES. T2 - 22nd European Symposium on Polymer Spectroscopy (ESOPS) CY - Berlin, Germany DA - 08.09.2024 KW - Microplastics Eluate Lysimeter KW - Microplastics KW - TED-GC/MS KW - Heavy Metals KW - PAH PY - 2024 AN - OPUS4-61013 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nordholt, Niclas T1 - The disinfectant glutaraldehyde induces antibiotic tolerance underpinned by a Disrupted Cellular State and Heterogenous Regrowth Dynamics N2 - Glutaraldehyde is widely used as a disinfectant and preservative, but little is known about its effects on bacterial susceptibility to antibiotics and the selection of tolerant phenotypes. We found that short-term exposure to sub-inhibitory levels of glutaraldehyde makes E. coli resistant to high doses of bactericidal antibiotics from different classes. This tolerance is associated with delayed, heterogeneous regrowth dynamics and global transcriptome remodeling. We identified over 1200 differentially expressed genes, including those related to antibiotic efflux, metabolic processes, and the cell envelope. The cells entered a disrupted state likely due to the unspecific mode-of-action of glutaraldehyde. Despite this unregulated response, we identified several differentially expressed genes not previously associated with antibiotic tolerance or persistence that induce antibiotic tolerance when overexpressed alone. These findings highlight how the unspecific mode-of-action of disinfectants can make bacteria temporarily resistant to antibiotics. They have implications for settings where disinfectants and antibiotics are used in close proximity, such as hospitals and animal husbandry, and for the selection dynamics of tolerant pheno- and genotypes in fluctuating environments where microorganisms are exposed to these substances, such as sewage systems. A trade-off arises from overcoming the disrupted state as quickly as possible and maintaining antibiotic tolerance. T2 - Molecular Mechanisms in Evolution (GRS) Gordon Research Seminar CY - Easton, Massachusetts, USA DA - 24.06.2023 KW - Glutaraldehyde KW - Biocides KW - Tolerance KW - Bacteria KW - Disinfection KW - Heterogeneity KW - Antibiotics KW - AMR PY - 2023 AN - OPUS4-58032 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nordholt, Niclas T1 - The interplay between biocides, phenotypic heterogeneity and resistance evolution N2 - An overview of the interplay between biocides, phenotypic heterogeneity and resistance evolution presented at the University Wroclaw. T2 - Invited seminar at the Department of Molecular Microbiology CY - Wroclaw, Poland DA - 08.04.2024 KW - Disinfectants KW - Biocide resistance KW - Phenotypic heterogeneity KW - Evolution PY - 2024 AN - OPUS4-61173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nordholt, Niclas T1 - Biocides and phenotypic heterogeneity N2 - An overview of our findings regarding the interplay between phenotypic heterogeneity in bacteria and biocides. T2 - One Health and Antimicrobial Resistance CY - Berlin, Germany DA - 29.01.2024 KW - Biocides KW - Phenotypic heterogeneity KW - Biocide resistance PY - 2024 AN - OPUS4-61174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nordholt, Niclas T1 - EVOCIDE: Preserving disinfectant efficacy by predicting evolution: exposing the principles of disinfectant survival and adaptation in bacteria N2 - Presentation of the EVOCIDE research proposal work programme.EVOCIDE seeks to gain a systems level understanding of disinfectant survival and evolution in bacteria. T2 - Joint Group Seminar Rolff-McMahon-Armitage-Steiner CY - Berlin, Germany DA - 20.12.2023 KW - Disinfectants KW - Evolution KW - Microbiology KW - Bacteria KW - Biocides PY - 2023 AN - OPUS4-59224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Song, Jessica T1 - Close encounters on a micro scale: Dynamics and interactions of microplastic biofilms in aquatic ecosystems. N2 - Microplastics circulate freely throughout aquatic ecosystems and, due to their interactive nature, accumulate complex polymeric matrices consisting of rich organic compounds and inorganic pollutants. Simultaneously, these hardy substrates offer nutrition and protection to diverse microbial communities and their theatre of activity, representing a new ecological niche. In our work, we investigate the interactions of microplastics in aquatic systems and characterise the effects of these interactions on associated microbial communities to better understand how these substrates might impact surrounding ecosystems. Demonstrating no specificity to polymer type, microplastic biofilms are shaped more by the strong influence of spatial and temporal factors. Microplastic sorption of polycyclic aromatic hydrocarbons (PAHs), in contrast, appear to be more strongly dictated by substrate type, with different polymers observed to sorb varying levels of different PAHs. These interactions between the different emerging contaminants were found in our study to have a significant effect on associated substrate biofilms. Elevated levels of specific 3- and 4-ring PAHs on polyethylene and polystyrene were found to coincide with a notable shift in community composition and structure, as well as a reduced diversity among biofilm communities. The findings in our study illustrate the importance of investigating the collective effect of pollutants in combination and their complex interactions in assessing their environmental impact. To fully understand how microplastics interact and alter surrounding ecosystems, the entire substrate must be considered, including all chemicals integrated into the polymeric matrix. T2 - Biofilms 11 Conference CY - Cardiff, Wales, UK DA - 13.05.2025 KW - Microplastics KW - Biofilms KW - PAHs PY - 2025 AN - OPUS4-63389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Investigating the Thermal Decomposition of PFAS in a Full-Scale Commercial Hazardous Waste Incinerator N2 - Incineration is currently the only commercial full-scale technology available to destroy per- and polyfluoroalkyl substances (PFAS) in large solid and liquid waste streams. Given previous experience of dioxin formation during halogenated waste incineration, concerns about the emission of products of incomplete destruction (PIDs) from PFAS incineration exist. The overarching objective of this project is to track the fate of fluorine during full-scale hazardous waste incineration in order to demonstrate the readiness, viability, and level of safety for thermal PFAS destruction in various waste streams. The specific objectives of this project are (1) to enhance our understanding of key variables and conditions on PFAS incineration performance, (2) to identify major PIDs under insufficient treatment conditions, (3) to explore the catalytic role of fly ash and other process-relevant surfaces in thermal PFAS decomposition, and (4) to determine the potential formation of polyfluorinated dibenzodioxins and dibenzofurans. T2 - CEN/TC 264/WG48 Symposium - Emissions and ambient air - Determination of PFAS CY - Düsseldorf, Germany DA - 16.07.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration PY - 2025 AN - OPUS4-63714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Panorama of Black writing inks: From Antiquity to the Middle Ages N2 - Black writing inks in the period under consideration can be divided into three different classes: soot, tannin and iron-gall ink. The first one is a fine dispersion of carbon pigments in a water-soluble binding agent, the second one is a solution of plant extract from tree barks or gallnuts, while the third one contains both soluble and insoluble phases. This last ink is based on metal (iron) and is produced by a chemical reaction of soluble iron (II) with tannin in aqueous solution. Tracing the transition from writing inks based on carbon pigments (soot or charcoal), common in Antiquity to the iron-gall inks commonly used in the Middle Ages builds a focus of our investigative work at the BAM (Federal Institute of Material Analysis and Testing) [1-5]. With the aim of creating a detailed history of writing black inks, we worked out a non-invasive protocol to collect statistically relevant ink data from dated and localized manuscripts covering a large time span and different geographic areas. The first step of our protocol consists of the screening carried out by means of imaging in the near infrared region. The optical differences between carbon, tannin, and iron-gall inks are best recognized by comparing their response to the infrared light: carbon ink has a deep black colour, iron-gall ink becomes transparent above 1400 nm, and tannin ink disappears at about 750 nm, we have simplified the analysis using a small USB microscope with built-in NIR (940 nm) and UV (395 nm) LED in addition to an external white light source [1]. Comparing the images under white and near infrared illumination, we determine the ink typology by observing the changes in the opacity of the ink. Here, carbon-based inks show no change in their opacity when illuminated with near infrared light, while the opacity of iron-gall inks changes considerably, and tannin inks become transparent. Our own recent finding that mixed carbon / iron-gall inks were quite popular in the late Antiquity and early Middle Ages suggested to return to the conventional method using infrared light in the spectral region 1000 – 1400 nm. The presentation will show the panorama of historic inks and our attempt to follow up the transition of the inks from those based on soot to the iron-gall inks commonly used in the Middle Ages. T2 - Public lecture CY - Manchester, UK DA - 01.02.2024 KW - Ink KW - Historic ink PY - 2024 AN - OPUS4-61201 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Black writing inks: From Antiquity to the Middle Ages N2 - Tracing the transition from writing inks based on soot, common in Antiquity to the iron-gall inks commonly used in the Middle Ages builds a focus of our investigative work at the BAM and the Centre for the Studies of Manuscript Cultures (CSMC) [1-4]. With the aim of creating a detailed history of writing black inks, we worked out a non-invasive protocol to collect statistically relevant ink data from dated and localized manuscripts covering a large time span and different geographic areas. The first step of our protocol consists of the screening carried out by means of the NIR & IRR reflectography. The optical differences between carbon, tannin, and iron-gall inks are best recognized by comparing their response to the infrared light: carbon ink has a deep black color, iron-gall ink becomes transparent above 1400 nm, and tannin ink disappears at about 750 nm, we have simplified the analysis using a small USB microscope with built-in NIR (940 nm) and UV (395 nm) LED in addition to an external white light source [1]. Comparing the images under white and near infrared illumination, we determine the ink typology by observing the changes in the opacity of the ink. Here, carbon-based inks show no change in their opacity when illuminated with NIR wavelength, while the opacity of iron-gall inks changes considerably, and tannin inks become transparent. Our own recent finding that mixed carbon / iron-gall inks were quite popular in the late Antiquity and early Middle Ages suggested to return to the conventional IRR method. The presentation will show the panorama of historic inks and our attempt to follow up the transition of the inks from those based on soot to the iron-gall inks commonly used in the Middle Ages. T2 - Seminar University of Oslo CY - Oslo, Norway DA - 23.09.2022 KW - Ink KW - Historic ink PY - 2022 AN - OPUS4-61194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Methoden und Erkenntnismöglichkeiten von Tintenanalysen N2 - Der Vortrag stellt die Palette der zerstörungsfreien analytischen Methoden, die zur Identifizierung und Vergleich der Tinten, Tuschen und Pigmente verwendet werden. T2 - Experten-Workshop CY - Hamburg, Germany DA - 06.10.2022 KW - Tinte KW - Tusche KW - Pigmente PY - 2022 AN - OPUS4-61195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Unveiling the use of writing materials in Carolingian manuscripts N2 - After having been neglected for a long time, materiality is nowadays of great interest in the study of manuscripts. This allows us to explore the variety (and potential coexistence) of different inks and pigments in type and composition in their use over time and geographical area. In this presentation, we aim to contribute to their study through archaeometric analyses of black and red inks used in Carolingian manuscripts copied between the 8th and the 10th centuries. These analyses are based on an interdisciplinary strategy, bringing together knowledge from the humanities and natural sciences to understand the global use of black and red inks in the Carolingian Empire. In this regard, we adopted a non-invasive protocol that included near-infrared imaging and X-ray fluorescence spectroscopy for on-site measurements supported by historical and palaeographic analysis. The results have been collected in the framework of two projects at the University of Hamburg in close collaboration with the Bundesanstalt für Materialforschung und -prüfung, Berlin (BAM) and will be compared with several other archaeometric studies of contemporary manuscripts. T2 - Novel approaches to Digital Codicology CY - Tours, France DA - 10.05.2023 KW - Carolingian manuscripts KW - Historick inks KW - Pigments PY - 2023 AN - OPUS4-61199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Imaging micro-XRF in studies of manuscripts N2 - Availability of mobile XRF-equipment with an interaction spot of ca. 100 µm produced a revolution in the studies of manuscripts. A protocol for the use of line-scans introduced in the beginning of 2000 permitted large scale and extremely successful investigations of the medieval iron-gall inks. Here, we usually focus on a comparison of the characteristic metallic components in the inks. In our work, we encountered cases that could be adequately addressed only using large area imaging XRF. However, conducting an M6 scan on a bound manuscript or on a scroll of huge dimensions is not a simple and easy matter. In our presentation, we want to share our experience by presenting a series of the case studies, in which many an original solution was found. T2 - M6 JETSTREAM European User Meeting CY - London, GB DA - 03.04.2023 KW - Micro-XRF KW - Manuscripts KW - Imaging PY - 2023 AN - OPUS4-61198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Authentic vs. inauthentic Dead Sea Scrolls from the point of view of material analysis N2 - The paper seeks to illuminate the problem of identifying forgeries among the Dead Sea Scrolls from the point of view of material analysis. It will present the sum of our technical knowledge of the skin-based material of the Dead Sea Scrolls, which includes the original treatment of the skins and the resulting typology as well as degradation effects due to their sojourn in caves and post-discovery interventions. We will try then to list the characteristic properties that must be found in the authentic material. We will supplement the presentation with a short description of the relevant methods of material analysis and their contribution to the secure identification of inauthentic Dead Sea Scrolls. T2 - Annual Meeting of the Siciety of Biblical Literature CY - Denver, CO, USA DA - 19.11.2022 KW - Dear Sea Scrolls KW - Forgery PY - 2022 AN - OPUS4-61196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Material analysis - results N2 - The presentations describes the results obtained by material analysis of the writing materials. Their relevance in the field of digital editing and publishing is discussed. T2 - Communicating Revealed Texts: Best Practices for Born-Digital Editions Using Enhanced Imaging CY - Iowa City, IA, USA DA - 29.06.2024 KW - Writing materials KW - Manuscripts KW - Material analysis PY - 2024 AN - OPUS4-61202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Advances in Characterization of Written Heritage N2 - The session discusses three brances of teh work on the manuscripts: ink analysis, parchment analysis by proteomics (Matthew Collins) and lipids (Mélanie Roffet-Salque); revealing of hidden text using AI. The example of Vesuvium Challenge is presented and discussed by Bren Seales. T2 - Scientific Methods in Cultural Heritage Research Gordon Research Conference CY - Vaud, Switzerland DA - 07.07.2024 KW - Written Heritage KW - Vesuvius challenge KW - Proteomics KW - Lipids PY - 2024 AN - OPUS4-61203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - Original, Kopie, Fälschung? Multispektralanalyse von Bauhauszeichnungen N2 - Der Vortrag widmet sich der materialwissenschaftlichen Analyse von Zeichnungen einiger Bauhausschülerinnen und Bauhausschüler und legt besonderen Fokus auf die verwendeten Farbmittel. Die Objekte werden mit nicht-invasiven bildgebenden Verfahren untersucht, in dem die Wechselwirkung zwischen Röntgen-, sichtbarem und infraroten Licht und den Zeichnungen studiert wird. Dier Analysen liefern nicht nur generell Erkenntnisse über die Art und Zusammensetzung und damit das Alter der verwendeten Farbmittel. Durch die Auffindung von Vorzeichnungen, die Bestimmung von Überarbeitungen und Korrekturen werden Erkenntnisse über die Genese von Zeichnungen gewonnen. Auf der Basis dieser materialwissenschaftlichen Erkenntnisse werden die Begriffe Original, Kopie, Fälschung diskutiert. Da die nicht-invasiven Untersuchungen einen umfassenden Einblick in die Materialität der – überwiegend aus Papier bestehenden – Objekte erlauben, bilden sie die Grundlage für die Erstellung nachhaltiger Konservierungs- und Restaurierungskampagnen und deren dauerhaften Erhalt. T2 - Rahmenprogramm zur Ausstellung "Das Leben der Objekte. Farbe und Papier am Weimarer Bauhaus" CY - Weimar, Germany DA - 12.01.2023 KW - Bauhaus KW - Zerstörungsfreie Prüfung KW - Farbmittel PY - 2023 AN - OPUS4-56847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehring, Grzegorz T1 - Breaking the limits of the non-destructive instrumental analysis of writing inks N2 - The ink analysis protocol developed through cooperation between the Bundesanstalt für Materialforschung und -prüfung in Berlin and the Centre for the Study of Manuscript Cultures at the University of Hamburg involves the use of imaging techniques for ink screening, followed by spectroscopic analysis. In our presentation, we will begin by briefly reviewing the history of writing inks and discussing the three main categories: carbon-based inks, plant, and iron-gall inks. We will address their chronology, precursors, and mixed forms, as well as the features that allow for their identification. Then, we will present the techniques we use in ink analysis, whereby we would like to highlight the limitations, advantages, and disadvantages of each approach. Finally, we will discuss the new mass-spectrometric method based on micro-sampling and using atmospheric solid analysis probe (ASAP). T2 - Future of the Past CY - Torun, Poland DA - 14.06.2023 KW - Ink analyses KW - Spectroscopy KW - Mass spectroscopy PY - 2023 AN - OPUS4-58882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bell, Jérémy A1 - Climent, Estela A1 - Gotor, Raúl A1 - Tobias, Charlie A1 - Martin-Sanchez, Pedro M. A1 - Rurack, Knut T1 - Dipstick coated with polystyrene-silica core-shell particles for the detection of microbiological fuel contamination N2 - Microbial contamination of fuels by fungi or bacteria poses risks such as corrosion and fuel system fouling, which can lead to critical problems in refineries and distribution systems and has a significant economic impact at every stage of the process. Many factors have been cited as being responsible for microbial growth, like the presence of water in the storage tanks. In fact, only 1 % water in a storage system is sufficient for the growth of microorganisms like bacteria or yeasts, as well as for the development of fungal biomass at the oil/water interface. This work presents a rapid test for the accurate determination of genomic DNA from aqueous fuel extracts. The detection is based on the use of polystyrene-mesoporous silica core-shell particles onto which modified fluorescent molecular beacons are covalently grafted. These beacons contain in the hairpin loop a target sequence highly conserved in all bacteria, corresponding to a fragment of the 16S ribosomal RNA subunit. The designed single-stranded molecular beacon contained fluorescein as an internal indicator and a quencher in its proximity when not hybridized. Upon hybridization in presence of the target sequence, the indicator and the quencher are spatially separated, resulting in fluorescence enhancement. To perform the assay the developed particles were deposited on different glass fibre strips to obtain a portable and sensitive rapid test. The assays showed that the presence of genomic DNA extracts from bacteria down to 50–70 μg L–1 induced a fluorescence response. The optical read-out was adapted for on-site monitoring by fitting a 3D-printed case to a conventional smartphone, taking advantages of the sensitivity of the CMOS detector. Such embedded assembly enabled the detection of genomic DNA in aqueous extracts down to the mg L–1 range and represents an interesting step toward on-site monitoring of fuel contamination. T2 - IMA 2023 CY - Chania, Greece DA - 18.09.2023 KW - Teststreifen KW - Test strip KW - Microbial KW - Mikrobiell KW - Smartphone KW - Particles KW - Partikeln PY - 2023 AN - OPUS4-58526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - McMahon, Dino Peter T1 - Termite Immunity (a molecular perspective) N2 - In this presentation, an overview of the termite immune system is given. The presentation covers the mechanistic underpinnings of the canonical immune pathways in insects; where there are areas of conservation or divergence in termites, as well as briefly going over some key gaps in knowledge. External immune capabilities are discussed as well as the implications and consequences of sociality for the evolution of collective immune defense systems in termites. T2 - International Termite Course (ITC) 2025 CY - Davie, FL, USA DA - 10.06.2025 KW - Termite KW - Immunity KW - Molecular KW - Evolution PY - 2025 AN - OPUS4-64745 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piechotta, Christian T1 - Development, Validation and Application of an Accelerated Weathering Protocol for Assessing Bisphenol A Release from Polycarbonate Materials into the environment N2 - Bisphenol A (BPA) is under continuous regulatory scrutiny and listed as substance of very high concern (SVHC). Particular concern is related to its frequent detection in surface waters, despite being readily biodegradable. Several studies have been conducted to investigate sources and pathways of BPA in the environment, concluding that its main use as monomer in polycarbonate (PC) contributes only marginally to environmental BPA releases over its life cycle. To better understand the actual releases of BPA from PC under environmental conditions, a newly developed methodology (Federal Institute for Materials Research and Testing, BAM) was applied, which comprises a novel accelerated weathering protocol for polycarbonate (PC) materials, combined with an advanced analytical setup allowing for improved detection of BPA at trace level concentrations. The weathering protocol achieves a 13.6-fold acceleration compared to Central European outdoor conditions and simulates environmental stressors (global radiation, rain, temperature variations) in a laboratory weathering chamber, with simultaneous BPA release measurements using an organic isotope dilution calibration LC-MS/MS approach. Validation was performed in parallel outdoor exposure tests, by using haze and yellowness index measurements as reference parameters. PC sample types representative of major polycarbonate applications were examined: Samples with different levels of UV-protection as used in transparent sheets used outdoor in construction or housings in Electro- and Electronic applications as well as samples with a protective coating as used in automotive applications (headlamps, glazing and construction). Results demonstrated consistently low total BPA releases of around 0.3 mg m⁻² for samples with exposed PC surfaces, while releases from coated samples were significantly reduced by around two orders of magnitude. In all cases examined, the BPA release ceased to zero after a period of four to six weeks, equivalent to approximately 1 to 1.5 years of outdoor exposure. This suggests that potential BPA releases diminish to virtually zero after that timespan. While the newly developed test method is not suitable for routine laboratory implementation, it provides crucial quantitative data on BPA release from PC materials during accelerated environmental weathering. T2 - Umwelt 2025 CY - Dessau, Germany DA - 22.09.2025 KW - Bisphenol A KW - Polycarbonate KW - Weathering PY - 2025 AN - OPUS4-64664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Charakterisierung historischer Schreibtinten: optische Eigenschaften und elementare Zusammensetzung N2 - Unsere Forschung zielt in erster Linie darauf ab, eine soziogeografische Geschichte von Tinte, Pergament und Papyrus zu rekonstruieren, und umfasst die Materialanalyse der Schreibtinten der Schriftrollen vom Toten Meer, der antiken und hellenistischen Papyri in Ägypten, sowie der Koptischen und Europäischen Tinten des Mittelalters. Zu diesem Zweck haben wir ein Protokoll für die zerstörungsfreie Tintenanalyse entwickelt. Es besteht aus einem ersten Screening mit Hilfe der VIS/NIR Fotografie, um die Art der Tinte zu bestimmen, und der anschließenden Analyse mit der Röntgenfluoreszenzanalyse (RFA). Letztere spielt eine wichtige Rolle bei der Identifizierung der Metalle in den Rußtuschen und der Bestimmung der charakteristischen Zusammensetzung metallhaltiger Tinten, um zwischen den verschiedenen Tinten zu unterscheiden. Der Vortrag bietet ein Panorama schwarzer historischer Schreibmittel und zeigt, dass die Materialanalyse einen wesentlichen Beitrag zur Beantwortung vieler kulturhistorischen Fragen leisten kann. T2 - Eingeladener Vortrag bei GStA CY - Berlin, Germany DA - 10.11.2025 KW - Tinte KW - Tusche PY - 2025 AN - OPUS4-64783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Current status of monitoring of PFAS release from industrial facilities N2 - Increasing studies report per- and polyfluoroalkyl substances (PFAS) in the ambient air and emissions from diverse industrial sources. Therefore, a comprehensive framework for characterizing PFAS emissions by identifying source-specific chemical fingerprints, evaluating emission pathways and assessing the impact of remediation technologies is needed. Depending on the type of PFAS, dedicated sampling and analytical procedures are required. Here, also the detection of possible PFAS transformation products, so-called products of incomplete combustion (PICs) are more mobile or toxic, is also of great interest to evaluate these technologies in terms of mineralisation potential and fluorine mass balance. T2 - Consortium for analysis and remediation of per- and polyfluoroalkyl substances (CAR-PFAS Japan) visit Uni Örebro CY - Online meeting DA - 09.10.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration KW - Remediation PY - 2025 AN - OPUS4-64318 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Per- and Polyfluoroalkyl Substances (PFAS) in Sewage Sludge and Wastewater-based Fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are chemicals which were developed to improve humanity’s quality of life. Due to their high chemical stability and resistance to degradation by heat or acids, PFAS were used in a variety of consumer products. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system resulted in the contamination of effluents and sewage sludge from wastewater treatment plants (WWTPs) (Roesch et al. 2022). Since sewage sludge is often used as fertilizer, its application on agricultural soils has been observed as a significant entry path for PFAS into the environment, specifically in our food chain. In Germany the sewage sludge/biosolid application on agricultural land was banned with the amendment of the German Sewage Sludge Ordinance and by 2029 sewage sludge application will be totally prohibited. However, phosphorus (P) from sewage sludge should still be recycled in WWTPs of cities with a population larger than 50,000 residents. To produce high-quality P-fertilizers for a circular economy, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Due to the strong diversity of industrial PFAS usage it is not clear if a safe application of novel recycled P-fertilizers from WWTPs can be guaranteed. Therefore, we analyzed various sewage sludges and wastewater-based fertilizers. Sewage sludge (SL) samples from various WWTPs in Germany and Switzerland, six sewage sludge ashes (SSA) from Germany, six thermally treated SL and SSA samples with different additives (temperatures: 700-1050 °C), two pyrolyzed SL samples (temperature: 400 °C) and two struvite samples from Germany and Canada were analyzed. The goal was to quantify PFAS in sewage sludges and wastewater-based P-fertilizers with the sum parameter extractable organic fluorine (EOF) by combustion ion chromatography (CIC). The results were compared with data from classical LC-MS/MS target analysis as well as selected samples by HR-MS suspect screening. The EOF values of the SLs mainly range between 154 and 538 µg/kg except for one SL which showed an elevated EOF value of 7209 µg/kg due to high organofluorine contamination. For the SSA samples the EOF values were lower and values between LOQ (approx. 60 µg/kg) and 121 µg/kg could be detected. For the pyrolyzed SLs no EOF values above the LOQ were detected. Moreover, the two wastewater-based struvite fertilizers contain 96 and 112 µg/kg EOF, respectively. In contrast to the EOF values, the sum of PFAS target values were relatively low for all SLs. Additional applied PFAS HR-MS suspect screening aimed to tentatively identify PFAS that could contribute to the hitherto unknown part of the EOF value. The majority of the detected fluorinated compounds are legacy PFAS such as short- and long-chain perfluorocarboxylic acids (PFCA), perfluorosulfonic acids (PFSA), polyfluoroalkyl phosphate esters (PAPs) and perfluorophosphonic acids (PFPA). Moreover, fluorinated pesticides, pharmaceutical as well as aromatic compounds were also identified, which are all included in the EOF parameter. Our research revealed that the current PFAS limit of 100 µg/kg for the sum of PFOS + PFOA in the German Fertilizer Ordinance is no longer up to date. Since the number of known PFAS already exceeds 10,000, the ordinance limit should be updated accordingly. Recent regulations and restrictions on using long-chain PFAS (≥C8) have resulted in a significant shift in the industry towards (ultra-)short-chain alternatives, and other, partly unknown, emerging PFAS. Ultimately, also fluorinated pesticides and pharmaceuticals, which end up as ultrashort PFAS in the WWTPs, have to be considered as possible pollutants in fertilizers from wastewater, too. T2 - Dioxin Konferenz CY - Maastricht, Netherlands DA - 10.09.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge KW - Fertilizer PY - 2023 AN - OPUS4-58345 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Combining DGT and combustion ion chromatography (CIC) as screening tool for per- and polyfluoroalkyl substances (PFAS) contamination in wastewater-based fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of organofluorine surfactants used in the formulations of thousands of consumer goods. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system have been resulted in contaminated effluents and sewage sludge from wastewater treatment plants (WWTPs) which became an important pathway for PFAS into the environment. Because sewage sludge is often used as fertilizer its application on agricultural soils has been observed as significant input path for PFAS into our food chain. To produce high-quality phosphorus fertilizers for a circular economy from sewage sludge, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Normally, PFAS are analyzed using PFAS protocols typically with time-consuming extraction steps and LC-MS/MS target quantification. However, for screening of PFAS contaminations in wastewater-based fertilizers also the DGT technique can be used for the PFAS extraction. Afterwards, combustion ion chromatography (CIC) can be applied to analyze the “total” amount of PFAS on the DGT binding layer. The DGT method was less sensitive and only comparable to the extractable organic fluorine (EOF) method values of the fertilizers in samples with >150 µg/kg, because of different diffusion properties for various PFAS, but also kinetic exchange limitations. However, the DGT approach has the advantage that almost no sample preparation is necessary. Moreover, the PFAS adsorption on the DGT binding layer was investigated via surface sensitive spectroscopical methods, such as Fourier-transform infrared (FT-IR) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - DGT Konferenz CY - Paris, France DA - 11.10.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge PY - 2023 AN - OPUS4-58575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Black ink from antiquity to the Middle Ages N2 - Il nostro lavoro di ricerca al BAM si concentra sul passaggio dagli inchiostri a base di fuliggine, comuni nell'antichità, agli inchiostri ferro-gallici, comunemente usati nel Medioevo. Con l'obiettivo di creare una storia dettagliata degli inchiostri neri, abbiamo elaborato un protocollo non invasivo per raccogliere dati statisticamente rilevanti sugli inchiostri da manoscritti datati e localizzati che coprono un ampio arco temporale e diverse aree geografiche. Il primo passo del nostro protocollo consiste nella selezione effettuata mediante riflettografia NIR e IRR. Le differenze ottiche tra gli inchiostri a base di carbonio, tannino e ferro-gallio sono meglio riconoscibili confrontando la loro risposta alla luce infrarossa: l'inchiostro a base di carbonio ha un colore nero intenso, l'inchiostro ferro-gallico diventa trasparente al di sopra dei 1400 nm e l'inchiostro a base di tannino scompare a circa 750 nm. abbiamo semplificato l'analisi utilizzando un piccolo microscopio USB con LED NIR (940 nm) e UV (395 nm) integrati, oltre a una fonte di luce bianca esterna. Confrontando le immagini sotto illuminazione bianca e nel vicino infrarosso, determiniamo la tipologia di inchiostro osservando i cambiamenti nell'opacità dell'inchiostro. In questo caso, gli inchiostri a base di carbonio non mostrano alcuna variazione di opacità quando illuminati con lunghezza d'onda NIR, mentre l'opacità degli inchiostri ferro-gallici cambia notevolmente e gli inchiostri tanninici diventano trasparenti. La nostra recente scoperta che gli inchiostri misti carbonio/ferro-gallici erano piuttosto diffusi nella tarda antichità e nell'alto Medioevo ci ha suggerito di tornare al metodo IRR convenzionale. Il secondo passo del protocollo prevede l'analisi micro-XRF per identificare i componenti inorganici dell'inchiostro. Nel caso degli inchiostri ferro-gallici, stabiliamo le impronte digitali, ovvero i rapporti caratteristici tra i componenti vitriolici dell'inchiostro e l'elemento principale, ferro. T2 - 1° SEMINARIO di studi dottorali CY - Benevento, Italy DA - 06.10.2025 KW - Ink KW - Historic ink PY - 2025 AN - OPUS4-64773 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Ink Analysis of Relic Texts N2 - The presentation will show the multitude of black writing inks in use during the late Antiquity and early Middle Ages in Europa and the Near East and our attempt to follow up the transition of the inks from those based on soot to the iron-gall inks commonly used in the Middle Ages. Black writing inks in the period under consideration can be divided into three different classes: soot, tannin and iron-gall ink. The first one is a fine dispersion of carbon pigments in a water-soluble binding agent, the second one is a solution of plant extract from tree barks or gallnuts, while the third one contains both soluble and insoluble phases. This last ink is based on metal (iron) and is produced by a chemical reaction of soluble iron (II) with tannin in aqueous solution. Tracing the transition from writing inks based on carbon pigments (soot or charcoal), common in Antiquity to the iron-gall inks commonly used in the Middle Ages builds a focus of our investigative work at the BAM (Federal Institute of Material Analysis and Testing). In this context, we will discuss the results of the ink analysis obtained within the project “Crafting documents”. T2 - Heritage Science and Manuscripts from Antiquity and the Middle Ages CY - Oxford, United Kingdom DA - 13.11.2025 KW - Ink KW - Historic ink PY - 2025 AN - OPUS4-64772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Material analysis of afghanistan liturgical quire (ALQ) conducted at the BAM N2 - The lecture presents the results of the detailed material analysis of the inks and of the parchment of the Afghanistan Liturgical Quire (ALQ), conducted at the Bundesanstalt für Materialforschung und -Prüfung (BAM) in Berlin. Testing was conducted using the following techniques: 3-color photography, 3D-digital microscopy, scanning μ-X-ray fluorescence analysis (XRF), μ- Raman and FTIR spectroscopy. I will give a short explanation of the principles of the techniques and explain the choice of the instruments. The main task of our work at the BAM required characterization of the inks and comparison of the ink as well as the composition of parchment. For the ink characterization we have followed the protocol developed at the BAM. The standard protocol includes three non-invasive stages: a) near infrared photography (NIRR) to determine the ink type or its main component; b) X-ray fluorescence analysis (XRF) to determine a fingerprint for iron-gall inks or contaminants in carbon/plant inks; c) Raman spectroscopy if there is an indication that the inks are of a mixed type. For parchment characterization, we usually employ µ-XRF-mapping and FTIR to gain information on specific treatments experienced by the parchment during its preparation and history. T2 - 19th World Congress of Jewish Studies CY - Jerusalem, Israel DA - 04.08.2025 KW - Hebrew Manuscripts KW - Parchment KW - Ink KW - XRF KW - NIR PY - 2025 AN - OPUS4-64776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Studies of the black writing inks N2 - In recent years, the interest in the composition of the inks in papyri documents grew exponentially. Different types of inks were found in the period 4th century BCE to 7th century CE. The paper will demonstrate a simple protocol based on comparison of the ink transparency in the near infrared light and X-ray fluorescence spectroscopy. The importance of including ink composition into new catalogues and possible formats of such data will be also presented and discussed. T2 - 31st International Congress of Papyrology CY - Cologne, Germany DA - 28.07.2025 KW - Ink KW - Historic ink KW - Papyrus PY - 2025 AN - OPUS4-64777 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Inks in Early Medieval Manuscripts from Chelles: a Scientific Study N2 - The talk will start with the overview of the ink types and the methods of their characterisation. After displaying XRF spectra of different Carolingian inks the talk will discuss Chelles collection and the labels attributed to Chelles. We will concentrate then on the study of the Chelles manuscripts preserved in Cologne, Vatican and Paris. We will show that there is a good degree of coincidence between the inks of the Chelles manuscripts and the labels attributed to Chelles. We observe unusually early use of vitriolic ink north of the Alps. T2 - Leeds International Medieval Congress (IMC 2025) CY - Leeds, United Kingdom DA - 07.07.2025 KW - Ink KW - Historic ink PY - 2025 AN - OPUS4-64778 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - The Power of networks – COST Action CA20130 N2 - For optimal research on microbiologically influenced corrosion (MIC), balanced and interdisciplinary cooperation is extremely important. However, differing perspectives, thought processes, and even variations in nomenclature/terminology often hinder the establishment of effective collaborations. Over the past four years, COST Action Euro-MIC (CA20130) has effectively addressed these discrepancies. Through regular meetings, conferences, and scientific exchanges, a large international network has been established. Many scientific findings and results have been achieved through scientific, interdisciplinary exchange within the international network. The upcoming presentation will highlight three examples (among many others) that have resulted in successful collaborations, third-party funding applications, publications, or outstanding results and emphasize that successful results in MIC research, facilitated by an interdisciplinary network, can lead more quickly to meaningful and application-oriented findings. Project 1&2 describe two different kinds of Projects related to the use of Nanoparticles; one is about the efficacy testing of novel Nanoparticles. Project 2 deals about how to apply already working and tested nanoparticles to different materials and conditions. Project 3a is related to the energy sector; a crucial part of our society, and currently undergoing significant changes. Climate change, rising temperatures, increased use of fertilizers and other environmental pollutants have led to an increasing occurrence of microorganisms and contamination in some sectors. But how we deal with “baggage” from the past and store nuclear waste without harm or risk for human and environment, but also how to transfer the gained knowledge to areas like safe Hydrogen storage in geological underground formation. T2 - ISMOS10 CY - Nashville, TN, USA DA - 11.08.2025 KW - COST Action CA20130 KW - MIC KW - STSM Grants KW - Networking PY - 2025 AN - OPUS4-64295 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Euro-MIC COST Action CA20130 Closing Workshop & Conference N2 - Ensuring the safety of offshore wind structures (OWS) is critical to guaranteeing their long-term performance and supporting reliable green energy supply. Microbiologically influenced corrosion (MIC) presents a significant challenge, particularly for monopiles in seabed environments. This study investigates the behavior of microorganisms and their impact on the corrosion process of carbon steel within monopiles. To simulate MIC at the sediment/water interface, an in-house experimental column was developed and inoculated with sediment and water samples from the North Sea. The system was operated under varying flow rates to replicate seabed movement conditions. Multiple molecular microbiological methods, surface analysis techniques, and other approaches were employed to assess the effects of different treatments. This study provides insights into MIC mechanisms in offshore environments and supports the development of strategies to monitor MIC in OWS infrastructure T2 - Final COST Action Conference - Horsens CY - Horsens, Denmark DA - 17.09.2025 KW - MIC KW - COST Action Euro-MIC KW - Interdisciplinarity PY - 2025 AN - OPUS4-64299 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Cost action EURO MIC (CA20130) N2 - Vorstellung des vor kurzen angelaufenen EU-Projekts: COST ACTION EURO MIC ( CA20130). Die BAM hat hierbei die Rolle des Chairs sowie Grant-Holding Institute. COST fördert internationale Netzwerk Aktivitäten. Durch COST Action können neue Kooperationen (Industrie, Akademie oder Politk) entstehen. T2 - Dechema CY - Online meeting DA - 10.11.2021 KW - Netzwerk KW - COST KW - Mikrobiell beeinflusste Korrosion KW - MIC PY - 2021 AN - OPUS4-54023 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Euro-MIC 2021-2025, our journey, and paths forward N2 - Microbiologically Influenced Corrosion (MIC) refers to the detrimental effects on materials caused by microorganisms, and it is becoming an increasingly significant issue for society. Unlike the USA, Canada, and Australia, Europe has less developed cooperation on MIC. Although several research groups and industrial stakeholders are addressing MIC, discussions remain fragmented, and information exchange is limited. A truly transdisciplinary approach is rarely seen. As a result, Europe often relies on methods, preventive measures, and standards from other regions, as there are no equivalent European standards. This situation makes Europe a) highly dependent, and b) in some cases, unable to use certain measures or standards due to European legal restrictions (e.g., the use of biocides). In 2021, researchers established the “Euro-MIC” network, financially supported by the EU project “COST-Action,” to tackle these issues. Through COST-Action, Euro-MIC aims to facilitate necessary interactions, communication, knowledge sharing, and training for personnel and researchers across various disciplines. COST-Action supports network activities, workshops, training schools, conferences, and more. Euro-MIC aspires to position Europe as a leader in MIC, promoting ideas on par with other nations while upholding European values and ensuring greater protection for people, property, and the environment. In this presentation, I will briefly introduce the principles of COST Action and highlight the significant opportunities provided by this EU-funded project. COST Action fosters interdisciplinarity, networking, training, scientific exchange, and the promotion of young scientists. By showcasing some examples of CA20130 COST ACTION Euro-MIC, I hope to demonstrate that COST Action is not only relevant for addressing MIC but can also be applied to other important topics and sectors. T2 - Unseen Corrosion: Unveiling Hidden Threats and Innovating Monitoring Solutions CY - Bergen, Norway DA - 15.05.2025 KW - COST Action CA20130 KW - MIC KW - Network KW - Corrosion KW - Microorganisms PY - 2025 UR - https://www.norceresearch.no/en/events/unseen-corrosion AN - OPUS4-63726 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Mikrobiell beeinflusste Korrosion (MIC) – Wenn MIC dann BAM N2 - In dieser Präsentation wurden dem Beirat Umwelt die High-Lights und der weitere Ausblick des Foresight Process MIC vorgestellt. Im Fokus stehen hierbei insbesondere die neu angelaufenen Projekte: COST Action Euro-MIC MIC im Endlager Hydrogen: MIC & Wasserstoffversprödung Biorezeptivität von Betonoberflächen Mitigation schwarze Pilze WIPANO ResTest T2 - Beirat Umwelt CY - Online meeting DA - 11.03.2022 KW - MIC KW - Hi-Tension KW - Projekte PY - 2022 AN - OPUS4-54463 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dinter, Adelina-Elisa T1 - Development of a single cell-ICP-ToF-MS-method for multielement analysis of MIC organisms grown on solid steel samples N2 - The latest ICP-MS technology - ICP-ToF (time of flight)-MS – enables the analysis of the multi-element fingerprint of individual cells. The interface between material and environmental analysis thus receives special attention, e.g., when considering corrosion processes. Microbiologically influenced corrosion (MIC) is a highly unpredictable phenomenon due to the influence of the environment, microbial communities involved and the respective electron source. However, the interaction pathway between cells and the metal surface remains unclear. The development of the MIC-specific ICP-ToF-MS analytical method presented here at the single cell level, in combination with the investigation of steel-MIC interactions, contributes significantly to progress in instrumental MIC analysis and will enable clarification of the processes taking place. For this, a MIC-specific staining procedure was developed. It allows the analysis of archaea at a single cell level and provides information about the interaction of the cells with the staining agent which is extremely scarce compared to other well characterized organisms. Additionally, the single cell ICP-ToF-MS is used for the analysis of archaea involved in MIC of steel. Hence, the possible uptake of individual elements from different steel samples is investigated - the information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials. T2 - DAAS Doktorandenseminar 2021 CY - Online meeting DA - 20.09.2021 KW - Sc-ICP-ToF-MS KW - Single cell analysis KW - Microbiologically influenced corrosion KW - Archaea PY - 2021 AN - OPUS4-53340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kirsch, Klemens T1 - Microbiologically Influenced Corrosion of Cast Iron Containers for High-Level Nuclear Waste Disposal N2 - Ductile and corrosion resistant cast iron is investigated as a potential container material to store high-level nuclear waste (HLW) in deep geological repositories (DGR) in claystone bedrock. The dynamic corrosion process is dependent on the conditions present in the DGR which are influenced and/or controlled by geochemical parameters (e.g., redox potential, pH, presence of and ionic concentration in (pore-)water), physical parameters (e.g., pressure), and the influence of metabolically active microorganisms. Cast iron corrosion will occur at the intersection of container and its decontaminable coating with the bentonite backfill material which contains natural microbial populations. The conditions in a DGR are simulated in microcosm experiments to investigate the impact of microbiologically influenced corrosion (MIC); the microcosms contain: B27 bentonite, synthetic pore water, N2 or N2-CO2 atmosphere, cast iron coupons, as well as the bacterium Desulfosporosinus burensis (isolated from repository depth in Buré, France). Three coupon configurations will be used: untreated, coated with decontaminable coating, and coated with decontaminable coating which has been damaged to simulate possible damages. The microcosms will be examined for bio- and geochemical parameters, such as pH, redox potential, mineral phases, sulphate concentration, Fe(II):Fe(III), changes in microbial populations, and the corrosion process for formation of corrosion products, and potential microbial influence, after a 270-day incubation period at 25°C under anaerobic conditions. In subsequent experiments, the sorption behavior of lanthanides and actinides onto the membranes of viable cells and spores of D. burensis, as well as the surface of corroded cast iron coupons will be investigated. T2 - 8th International Workshop on Long-term Prediction of Corrosion in Nuclear Waste Systems 2022 CY - Baden, Switzerland DA - 21.06.2022 KW - Microbiologically influenced corrosion (MIC) KW - Cast iron KW - Nuclear waste disposal PY - 2022 AN - OPUS4-55154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Olbrich, Adelina-Elisa T1 - Material vs. Environment: Uncovering microbiological influenced corrosion processes on steel with single cell-ICP-ToF-MS N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process dictated by the environment, microorganisms, and the respective electron source. Interaction pathways between cells and the metal surface remain unclear. The development of this novel single cell-inductively coupled plasma-time of flight-mass spectrometry analytical method and a MIC-specific staining procedure facilitate the investigation of steel-MIC interactions. With this it is possible to analyze the multi-elemental fingerprint of individual cells. The detection method revealed elemental selectivity for the corrosive methanogenic archaeal strain Methanobacterium-affiliated IM1. The interface between material and environmental analysis thus receives special attention, e.g., when considering MIC on solid steel. Hence, the possible uptake of individual elements from different steel samples is investigated. Results showed the cells responded at a single-cell level to the different types of supplemented elements and displayed the abilities to interact with chromium, vanadium, titanium, cobalt, and molybdenum from solid metal surfaces. The information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials research. T2 - ToFcon 2022 CY - Online meeting DA - 17.11.2022 KW - Single cell KW - Microbiological influenced corrosion MIC KW - Sc-ICP-ToF-MS KW - Method development KW - Ir DNA staining approach KW - Carbon steel corrosion PY - 2022 AN - OPUS4-56355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - COST-Action - EURO-MIC (CA20130) European MIC Network - New paths for science, sustainability and standards N2 - Microbiologically Influenced Corrosion (MIC) is a phenomenon that is increasingly becoming a problem for the society. MIC describes the negative effects a material can experience due to the presence of microorganisms. In Europe, several research groups/ other industrial stakeholders are already dealing with MIC. Unfortunately, the discussions are fragmented and the exchange of information is limited. A true transdisciplinary approach is hardly ever experienced, although this would be logical for this material/biology related challenge. USA, Canada and Australia have strong networks, and develop methods, prevention measures and standards, which Europe is forced to use, since nothing similar exists for a network and combined knowledge to design them according to european standards. This makes Europe extremely dependent and, in some cases, the potential measures or standards cannot been used because the suggested solutions are prohibited by European laws (e.g. use of biocides). Therefore, it is important to initiate a new European MIC-network. Europe needs to combine the efforts as experts in different fields and develop prevention measures according to the European rules, in close cooperation with industry and plant operators and owners of critical infrastructure. This COST Action will provide the necessary interaction and communication, knowledge sharing, training of personnel and of researchers of different disciplines. This will bring Europe to a leading role in this process, bringing ideas on an equal level with other nations, considering the values which are important for Europe and attitudes (e.g.environmental protection) and representing greater protection for people, property and the environment. The main aim and objective of the Action is to , in the context of MIC-research/control, encourage a fluent/synergistic collaboration/communication, closing the gap between materials scientists, engineers, microbiologists, chemists and integrity managers to encourage sufficient interaction between academia and industry. This Action will create a common MIC-Network, including the important stakeholders. T2 - EuroCorr CY - Online meeting DA - 19.09.2021 KW - COST Action KW - MIC KW - Interdisciplinary KW - Stakeholder KW - Academia PY - 2021 AN - OPUS4-53382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abilio, André T1 - Expert System for Screening Microbiologically Influenced Corrosion asInternal Failure Cause in Oil and Gas Upstream Pipelines N2 - The analysis of pipeline failures due to Microbiologically Influenced Corrosion (MIC) is challenging due to the complex interaction of many influencing parameters including pipeline operation conditions, fluid chemistry and microbiology, as well as the analysis of corrosion features and products. To help address this challenge, an expert system was developed to assist non-specialists in screening internal pipeline corrosion failures due to MIC related threats. To accomplish this, 15 MIC subject matter experts (with a total of 355 man-years of accumulated MIC based experience) were recruited to evaluate a total of 65 MIC failure cases based on real-life scenarios. These case study parameters and the expert elicited results were input into an Artificial Neural Network (ANN) model to create a model system which can screen whether a given failure scenario is one of three outcomes: a) failure is likely due to MIC, b) failure is likely not due to MIC, or c) the conclusion is inconclusive (analysis needs more data/information). The model system had an overall accuracy of 74.8%and it showcases that knowledge from subject matter experts can be captured in a reasonably effective way to screen for possible MIC failures. Based on that, this presentation will provide details of the model development process and key results to date. Important considerations regarding the level of confidence of the diagnoses and variation between expert opinion will also be discussed alongside with ideas on how to improve the model for field applicability. T2 - ISMOS 9 CY - Edinburgh, United Kingdom DA - 27.06.2023 KW - Expert System KW - Microbiologically Influenced Corrosion (MIC) KW - Oil and Gas Upstream KW - Artificial neural networks (ANNs) KW - Failure analysis PY - 2023 AN - OPUS4-64602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - Analytische Untersuchungen für Vitrinenbaumaterialien am Beispiel des BEMMA-Schemas N2 - BEMMA ist die Kurzbezeichnung für ein Verfahren zur Bewertung von Emissionen aus Materialien für Museumsausstattungen. Die Bewertung der Materialien erfolgt nach StAA-QMH-4.2-033. Mit diesem Verfahren lassen sich flüchtige organische Verbindungen aus modernen Werkstoffen, die in mittelbarem Kontakt mit historischen Materialien des Kunst- und Kulturgutes stehen, untersuchen und bewerten. Die Vitrinenbaumaterialien, nicht die Vitrine, werden im Hinblick auf ihre Emissionen bewertet. Die Ergebnisse der Messungen werden auch vor dem Hintergrund von realen Vitrinenmessungen eingeordnet und die Herausforderungen bei der Probenahme dargestellt. T2 - Klima- und Schadstoffmanagement in der passiven Vitrine Aktuelle Forschungsergebnisse CY - Berlin, Germany DA - 13.10.2025 KW - Emission KW - BEMMA KW - Vitrinen KW - VOC PY - 2025 AN - OPUS4-64529 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Wasserstofflagerung in unterirdischen geologischen Formationen und potenzielle Risiken durch Mikroorganismen N2 - Bei dem Vortrag werden die potentiellen mikrobiologischen Einflüsse im Falle der Lagerung von Wasserstofflagerung in unterirdischen geologischen Formationen vorgestellt, die Zusammenarbeit mit internen und auch externen Partnern. Der Fokus liegt dabei auf UGF; anaerobe Umgebungen, Sulfate reduzierenden Bakterien, methanogenen Archaea, weiterleitenden Systeme und die Kombination der Untersuchung abiotisch/biotische T2 - VDI-Schadensanalyse (49) CY - Würzburg, Germany DA - 17.10.2023 KW - MIC KW - Wasserstofflagerung KW - Unterirdische Speicher KW - Kontamination von H2 KW - H2-Abbau KW - Mikroorganismen KW - Biotische/abiotische Faktoren PY - 2023 AN - OPUS4-58645 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - An, Biwen Annie T1 - Standardization of MIC laboratory testing: with a special focus on corrosive methanogens N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process involving a complex group of microorganisms, including sulfate-reducing bacteria and methanogens. Standard laboratory MIC testing using static serum bottle enrichments is an easy but limited method, offering poor resolution on the biomineralization process of corrosion products. An example of this is the presumed corrosion product siderite by corrosive methanogens (Mi-MIC). Previous publications reported siderite was the sole corrosion product of M. maripaludis using metal coupons incubated under stationary conditions. However, the formation of siderite is closely related to the surrounding environmental conditions, i.e. pH, CO2 concentration, flow and temperature. Thus, siderite as the sole corrosion product of Mi-MIC remain inconclusive and questionable. To study Mi-MIC effectively, a novel versatile multiport flow-column corrosion monitoring system (MFC) was developed. MFC allows sectional corrosion rate determination under flow conditions using different types of material, inoculum and packing material. MFC offers great flexibility, ease of operation and accurate corrosion measurements that can be combined with many other techniques. Using MFC, we studied multiple strains of methanogens and compared it with sulfate-reducing bacteria under neutral and low pH conditions. It was revealed by MFC that corrosive methanogens have equally high corrosion potential as sulfate-reducing bacteria. Additionally, siderite is not the dominant nor sole corrosion product of Mi-MIC. Thus, effective corrosion monitoring and establishing standard laboratory practices, i.e. incorporating MFC as part of regular testing process, will provide deeper understanding of MIC. This will allow further microbial electrophysiology understandings, contributing to effective mitigation strategy development. T2 - EUROPEAN MIC NETWORK WEBINAR CY - Online meeting DA - 19.05.2020 KW - MIC KW - Methanogen KW - FIB/SEM KW - Corrosion products KW - Microbiologically influenced corrosion KW - Flow Model KW - Modelling KW - Korrosion PY - 2020 AN - OPUS4-51554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Mikrobielle Zusammensetzung im Wassertank N2 - Der Fachbereich 7.6 untersucht seit einiger Zeit an Auslagerungsständen auf dem Testgelände in Horstwalde Korrosion im maritimen Bereich. Im Moment läuft das System mit künstlichem Meerwasser und simuliert die Bewitterung von Metallproben unter angenäherten klimatischen Bedingungen ähnlich zum natürlichem Habitat. Im Laufe der Zeit konnte nicht intendierter mikrobieller bewuchs beobachtet werden. Es stellte sich die Frage, welche Mikroorganismen vorlagen und ob diese einen Einfluss auf die Korrosionsuntersuchungen haben könnte. Aus diesem Grund wurden 16S-rRNA Untersuchungen durchgeführt welche alle drei Domänen des Lebens widerspiegeln Bakterien, Archaea und Eukaryoten. Es konnte gezeigt werden, dass über 95% der vorliegenden Biomasse Grünalgen waren, die durch Licht Eintrag in den Container Photosynthese betrieben und dadurch an Biomasse zunahmen. Des weiteren konnten Bakterien detektiert werden, welche in der Regel halophilen und aeroben Habitaten zu finden sind. Allerdings wurden auch Sulfat reduzierende Bakterien (MIC) detektiert, wenn auch in einem geringen prozentualen Anteil. Es muss allerdings Berücksichtigt werden, dass die mikrobielle Zusammensetzung sich im Laufe der Zeit weiter ändern kann. Als Ursprung der Biomasse wird, das künstliche Sediment vermutet. Außerdem wäre es für zukünftige Experiment denkbar, das System mit echtem Sediment aus dem marinen Habitat anzuimpfen. T2 - Dechema CY - Online meeting DA - 10.11.2021 KW - Mikroorganismen KW - Mikrobielle Gemeinschaft KW - Korrosion KW - Simulation PY - 2021 AN - OPUS4-54035 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Mikrobielle Einflüsse auf Wasserstoffspeicherung: Materialien, Abbauprozesse und Teststrategien N2 - Wasserstoff gilt als Schlüsseltechnologie für die Energiewende – doch seine sichere Anwendung stellt neue Anforderungen an Technik, Infrastruktur und Personal. Die Veranstaltung „H₂ Sicherheit“ bietet eine umfassende Plattform, um sich über die sicherheitsrelevanten Aspekte von Wasserstoff zu informieren und praxisnahe Lösungen kennenzulernen. Expert:innen aus Forschung, Industrie und Netzbetrieb geben Einblicke in aktuelle Entwicklungen, Herausforderungen und Best Practices. Fokus dieser Präsentation war der Mikrobielle Einfluss bei der unterirdischen Speicherung von Wasserstoff und das neuartige Testsystem (MISTRAL) T2 - DVGW- H₂ Sicherheit | 26. – 27. November 2025 CY - Online meeting DA - 26.11.2025 KW - MIC KW - MISTRAL KW - Hochdruckbehälter KW - Wasserstoff KW - Unterirdische geologische Formationen PY - 2025 AN - OPUS4-64890 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - Nanoparticle Characterisation - The long way to standardisation N2 - Diese Präsentation gibt einen Überblick über die Entwicklung der Nanopartikelforschung von ca. 2005 bis heute. Beginnend mit den Besonderheiten von Nanopartikeln und der Aufnahme in den menschlichen Körper über Messmethoden bis hin zur Entwicklung einer Prüfrichtlinie im Rahmen der OECD und einem Ausblick über die absehbaren digitalen Entwicklungen. T2 - Abteilungsseminar der Abteilung 4 CY - Berlin, Germany DA - 27.02.2025 KW - Nanomaterials KW - Nano KW - OECD KW - Standardisierung KW - Advanced Materials PY - 2025 AN - OPUS4-64977 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Tintencharakterisierung: Optische Eigenschaften und elementare Zusammensetzung N2 - Die Präsentation beschreibt alle Typen der schwarzen Schreibmaterialien, die in der Antike und Mittelalter benutzt wurden. Weiterhin wir das bei der BAM entwickelte Untersuchungsprotokoll präsentiert, das aus zwei Stufen besteht: a) der Feststellung des Tintentyps anhand der optischen Eigenschaften; die Ausrechnung von den Fingerprints der Eisengallustinten anhand der elementaren Zusammensetzung. Die Arbeit wird durch Fallbeispiele illustriert. T2 - Schriftkulturen des Mittelalters in digitaler Perspektive CY - Berlin, Germany DA - 22.08.2025 KW - Tinte KW - Tusche PY - 2025 AN - OPUS4-64775 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - The Temple Scroll: Reconstructing an Ancient Manufacturing Practice N2 - The presentation shows the studies of ancient parchment and leather conducted by the authors within last 20 years. Presentation specifically focusses on poduction of the parchment of the Temple scroll. The practice unites the early production of modern parchment with the lost way of skin splitting. T2 - The Temple Scroll: A Research Colloquium CY - New York City, USA DA - 24.02.2025 KW - Dead Sea Scrolls KW - Parchment KW - Tanning PY - 2025 AN - OPUS4-64779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - The digital product passport N2 - This presentation contains information for industry and the scientific communitiy about the new digital product passport and the demands from the EU. Furthermore a short overview is given about the different supporting activities which are currently under developement by BAM. T2 - 3. Netzwerktag Cluster Nanotechnologie CY - Würzburg, Germany DA - 02.07.2025 KW - DPP KW - ESPR KW - Product Passport KW - Ökodesignrichtlinie KW - DMP PY - 2025 AN - OPUS4-64964 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wen, Keqing T1 - In situ analysis of biofilm formation under different flow regimes with the help of a microfluidic platform N2 - Bacteria often live in habitats characterized by fluid flow, which is ubiquitous in a diverse range of environments such as surface waters, wastewater treatment facilities, pipelines, and medical implants. Bacterial adhesion on surfaces may lead to biocorrosion and biodegradation. In comparison to traditional static and macro flow chamber assays for biofilm formation studies, microfluidic chips allow in situ monitoring of biofilm formation and biofilm related gene expression under various flow regimes. We developed a complete microfluidic platform to investigate biofilms under precisely controlled flow conditions. This platform central unit is a single-inlet microfluidic flow cell with a 5 mm wide chamber tested and analyzed by imaging tracking velocimetry (PIV) to achieve ultra-homogenous flow in the central area of the chamber. Additionally, dedicated microstructures were introduced to the chamber’s center to favor and localize bacterial adhesion and biofilm formation pattern. The flows and vortices induced by the structure were analyzed by computational fluid dynamics (CFD) and related to shape and dimension of the biofilm formed by Escherichia coli TG1. The major proteinaceous component of E. coli biofilms are extracellular amyloid fibers (curli) consisting of major (CsgA) and minor (CsgB) subunits. We used the promotor probe plasmid pRU1701 to monitor csgB-promotor activity under different flow regimes in complex and minimal medium. For comparison, csgB promotor activity in a batch liquid culture and curli production on LB and M9 agar plates were assessed. The microfluidic platform represents a powerful and versatile tool for studying biofilm in flow. The setup shows great potential for the yet not too much explored in flow monitoring of biofilm formation and related gene expression under hydrodynamic stresses. T2 - International Biodeterioration and Biodegradation Symposium (IBBS) 19 CY - Berlin, Germany DA - 09.09.2024 KW - Microfluidics KW - Biofilm KW - Escherichia coli KW - Curli PY - 2024 AN - OPUS4-61911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - The roles of DHN melanin and the stress-activated MAP kinase in the rock inhabitant Knufia petricola N2 - Black fungi/yeasts exhibit high stress tolerance, yeast‑like or meristematic growth, and constitutive 1,8-dihydroxynaphthalene (DHN) melanin formation. Due to their slow growth, robust cell walls and the lack of sexual cycles and genetic tools, the underlying mechanisms of their phenotypic traits have remained largely unexplored. Using recently developed genetic tools, it is now possible to manipulate the genome of the rock-inhabiting model fungus Knufia petricola. Thus, gene functions and the cell biology of black fungi can be studied using CRISPR/Cas9-based genome editing and live-cell imaging with genetically encoded fluorescent proteins. Here, we are addressing the question to which extent constitutive pigment formation (melanin and carotenoids) and responses mediated by the stress-activated mitogen-activated protein (MAP) kinase contribute to the observed extremotolerance of K. petricola. The mutations of pks1, phs1 and both genes result in melanin-free (pink), carotenoid-free (black) and pigment-free (white) strains, respectively. The other putative melanogenic genes were identified in the genome, deleted to confirm their involvement in DHN melanogenesis and co-expressed in Saccharomyces cerevisiae for reconstruction of the synthesis pathway. Sak1 encoding the stress-activated MAP kinase was deleted in the wild-type and different pigment-deficient backgrounds. Growth of the obtained single, double and triple deletion mutants was tested by droplet tests on media supplemented with different stress-inducing agents. The Δsak1 mutants show slightly reduced growth rates even without environmental pressure and are hypersensitive to different stresses: e.g. osmotic, oxidative, membrane, pH and heat stress. Melanin-free Δsak1 mutants are more sensitive than black Δsak1 mutants to some but not all stress conditions, suggesting that melanin and the SAK1 pathway have complementary roles in protecting K. petricola from stress. T2 - 16th European Conference on Fungal Genetics CY - Innsbruck, Austria DA - 05.03.2023 KW - Black fungus KW - Extremotolerance KW - Pigments PY - 2023 AN - OPUS4-57147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -