TY - CONF A1 - Adam, Christian T1 - What is in your opinion the fertiliser of the future? N2 - Conventional fertilisers have their disadvantages as nutrient release is not synchronised with the demand of plants. Several approaches of "next generation fertilisers" are aiming at controlled nutrient release. Recycling fertilisers are often not soluble in water but fully plant available. They are suitable raw materials for the production of new types of controlled release fertilisers. T2 - CLOOP-Workshop "What is in your opinion the fertiliser of the future?" CY - Berlin, Germany DA - 22.10.2019 KW - Controlled release fertilisers KW - Recycling fertilisers PY - 2019 AN - OPUS4-49554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Weimann, Karin T1 - Verwertung carbonfaserhaltiger Reststoffe in der Pyrometallurgie N2 - Carbonfasern sind äußerst stabil und werden auch in Anlagen zur Verbrennung von Sondermüll kaum zerstört. Beim Handling carbonfaserhaltiger Abfälle können Gesundheitsrisken auftreten (Abgabe von WHO-Fasern). Es werden Methoden der Verwertung carbonfaserhaltiger Reststoffe in der Pyrometallurgie diskutiert. T2 - UBA Fachaustausch: Aufbereitung und Verwertung carbonfaserhaltiger Abfälle CY - Dessau, Germany DA - 19.09.2019 KW - Carbonfasern KW - Pyrometallurgie PY - 2019 AN - OPUS4-49555 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery from waste water, sewage sludge and sewage sludge ashes N2 - A lecture was given about the technical possibilities of phosphorus recovery from waste water, sewage sludge and sewage sludge ashes. The specific situation of Europe and Germany was explained in the context of raw materials dependencies and the legal framework. T2 - Lecture at University of Sao Paulo, Brasil CY - Berlin, Germany and Sao Paulo, Brasil DA - 11.11.2019 KW - Phosphorus recovery KW - Recycling fertilisers KW - Sewage sludge ordinance PY - 2019 N1 - Vorlesung über Adobe Connect an der University of Sao Paulo, Brasilien AN - OPUS4-49590 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon A1 - Mohr, Gunther A1 - Baesso, Ilaria A1 - Straße, Anne A1 - Pittner, Andreas A1 - Pignatelli, Giuseppe A1 - Seeger, Stefan A1 - Nazarzadehmoafi, Maryam A1 - Ehlers, Henrik A1 - Gohlke, Dirk A1 - Homann, Tobias A1 - Scheuschner, Nils A1 - Ulbricht, Alexander A1 - Heinrich, P. A1 - Maierhofer, Christiane T1 - Process monitoring of additive manufacturing of metals - an overview of the project ProMoAM N2 - The project ProMoAM is presented. The goal of the project is to evaluate which NDT techniques or combination of techniques is suited for in-situ quality assurance in additive manufacturing of metals. To this end, also 3d-data fusion and visualization techniques are applied. Additional ex-situ NDT-techniques are used as references for defect detection and quantification. Feasability studies for NDT-techniques that are presently not applicable for in-situ use are performed as well. The presentation gives a brief overview of the whole project and the different involved NDT-techniques. T2 - Workshop od Additive Manufacturing: Process, materials, simulation & implants CY - Berlin, Germany DA - 13.05.2019 KW - Additive manufacturing KW - Process monitoring KW - NDT PY - 2019 AN - OPUS4-48087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - An, Biwen Annie A1 - Koerdt, Andrea A1 - Brüggemann, Kristin A1 - Wurzler, Nina A1 - Kleinbub, Sherin A1 - Özcan Sandikcioglu, Özlem T1 - Effect of biocides on highly corrosive methanogenic Archaea N2 - Biocide mitigation strategies of microbiologically influenced corrosion (MIC) in the oil and gas industry have been primarily used to eliminate the growths of sulfate-reducing microorganisms (SRM). However, methanogenic Archaea (MA) can also be highly corrosive by using iron as an electron source for methanogenesis. Because of the fundamental physiological differences between archaea and bacteria, responses of MA towards SRM-specific biocides cannot be deduced using SRM. Due to the lack of information available on the effect of biocides on corrosive MA, we selected THPS, glutaraldehyde, nitrate and perchlorate to compare against corrosive SRM. Preliminary results showed that at low concentrations of THPS (0-10 ppm), growth of MA was not affected, methane production and corrosion rates (0.1 mm/yr) were comparable between the different THPS concentrations. On the contrary, the SRM strain showed decreased corrosion rates (0.18 mm/yr to 0.03 mm/yr) with increasing THPS concentrations. Further corrosion tests including electrochemical measurements of different biocides on the growth of MA and SRM will be conducted. Such knowledge not only provide important insights on the physiological response of MA to biocides but also contribute to more effective mitigation strategies that can be both economic and environmentally beneficial. T2 - 25th Annual Reservoir Microbiology Forum CY - London, UK DA - 20.11.2019 KW - Corrosion KW - Methanogen KW - Microorganism KW - Biocide PY - 2019 AN - OPUS4-49788 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Del Mastro, G. A1 - Hammerstaedt, J. A1 - Mocella, V. A1 - Rabin, Ira T1 - XRF ink analysis of selected fragments from the Herculaneum collection N2 - Hundreds of papyrus rolls, carbonized during the 79CE eruption of Mount Vesuvius, were discovered in 1754 at Herculaneum. Sophisticated mechanical methods for unrolling the best-preserved scrolls have been applied, with varying success. However, such processes have been abandoned, to prevent risk from irremediable damage or loss and to preserve the integrity of the extremely fragile rolls. Following the development of X-ray based non-invasive techniques, attempts to virtually unroll the scrolls were made. The most common ink in Antiquity was carbon-based, and the main element of carbonized papyrus is carbon, making these investigations difficult. However, some attempts with synchrotron X-ray phase-contrast tomography (XPCT) were successful. Recently, the identification of antique inks containing metals raised hope that if some of the inks contain metal the rolls can be virtually unrolled using conventional CT- technique. We are presenting here the first results of a preliminary analysis, which aimed at identifying scrolls whose ink contains metals. T2 - Konferenz: 29th International Congress of Papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Herculaneum KW - Papyrus KW - Tomography KW - XRF KW - Ink PY - 2019 AN - OPUS4-48615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Bosch, S. A1 - Rabin, Ira A1 - Hahn, Oliver T1 - Scientific service project z02 at the CSMC: material science methods of reconstructing the history of manuscripts N2 - Z02 is one of the three technically supporting projects at the Centre for the Study of Manuscript Cultures (CSMC). In collaboration with the other two service projects, Z01 and Z03, it aims at bridging the gap between humanities and natural sciences and technology. To that purpose, we set up a laboratory with a range of high-end instruments, most of them mobile, allowing thorough non-destructive analysis of manuscripts. In addition to working on constantly improving the laboratory and the methods of analysis, a substantial part of our activities is dedicated to service, by supporting different research projects conducted at the centre. In this talk, we will present our equipment and the possibilities offered by the different techniques available regarding the different kinds of missions: typology and classification of inks, provenance studies, recovery of faded inscriptions and palimpsests, reconstruction of the history of manuscripts, authentication and dating. We will give a brief overview of our past and ongoing activities in the frame of the second phase of the CSMC. Finally, a selection of three projects will be presented in greater detail to highlight the possibilities of our laboratory and the diversity of missions which can be carried out. T2 - International Medieval Conference CY - Leeds, United Kingdom DA - 01.07.2019 KW - Manuscript KW - Ink KW - Pigment PY - 2019 AN - OPUS4-48465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike A1 - Eisentraut, Paul A1 - Kalbe, Ute A1 - Wachtendorf, Volker T1 - Elastomere und TPE – Gut für die Umwelt? – Kreislaufwirtschaft und Normung vereinen N2 - Der Vortrag fasst Projekte an der BAM mit Hinblick auf Elastomere und Umweltthemen zusammen. T2 - DIN Workshop: Elastomere und TPE – Gut für die Umwelt? – Kreislaufwirtschaft und Normung vereinen CY - Berlin, Germany DA - 08.08.2019 KW - Mikroplastik KW - Reifenabrieb KW - Sportböden PY - 2019 AN - OPUS4-49064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Braun, Ulrike A1 - Hodoroaba, Vasile-Dan A1 - Jann, Oliver A1 - Seeger, Stefan A1 - Unger, Wolfgang A1 - Resch-Genger, Ute T1 - Forschungsprojekte an der BAM N2 - Übersicht über die laufenden Projekte der BAM mit Bezug zur Nano-Thematik. Der Fokus liegt auf der Entwicklung der OECD-Prüfrichtlinie zur Partikelgrößenverteilung und auf den Projekten, die einen Anknüpfungspunkt für die anderen Bundesoberbehörden bilden könnten. T2 - Behördenklausur zur Nanosicherheit 2019 CY - Berlin, Germany DA - 26.06.2019 KW - Bundesoberbehörden KW - Nano KW - Behördenklausurtagung PY - 2019 AN - OPUS4-49575 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Rühle, Bastian A1 - Hodoroaba, Vasile-Dan A1 - Seeger, Stefan A1 - Resch-Genger, Ute A1 - Braun, Ulrike A1 - Jann, Oliver A1 - Wilke, Olaf A1 - Geißler, Daniel A1 - Schmidt, Alexandra A1 - Unger, Wolfgang A1 - Sturm, Heinz T1 - Stand der Aktivitäten zur gemeinsamen Forschungsstrategie N2 - Die gemeinsame Forschungsstrategie der Bundesoberbehörden zur Nanotechnologie wurde 2016 veröffentlicht. Die darin enthaltenen Aufgaben wurden von den Bundesoberbehörden vielfältig bearbeitet. Diese Präsentation gibt einen Überblick über die Projekte, die von der BAM bis 2019 bearbeitet wurden/werden und sich in den Rahmen der Forschungsstrategie einordnen. T2 - Workshop zur gemeinsamen Forschungsstrategie der Bundesoberbehörden „Nanomaterialien und andere innovative Werkstoffe: anwendungssicher und umweltverträglich“ CY - Berlin, Germany DA - 02.09.2019 KW - Nano KW - Bundesoberbehörden KW - Forschungsstrategie KW - Nanomaterialien KW - Nanotechnologie PY - 2019 AN - OPUS4-49586 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bucar, K. A1 - Zitnik, M. A1 - Stabile, L. A1 - Ozan, J. A1 - Seeger, Stefan T1 - Performance of a Sharp GP2Y low-cost aerosol PM sensor N2 - Simple particulate matter sensors are gaining popularity due to their low price, easy handling and good temporal resolution. In this presentation, we report on the performance of a Sharp optical PM sensor GP2Y1010AU0F, which costs less than 15 €. The sensor is built around an infrared emitting diode (ILED) and a phototransistor detecting the light scattered from the aerosol particle. An electronic circuit shapes the detected light in a pulsed signal. The manufacturer advises sampling the output signal 280 microseconds after the ILED pulse. The measured output voltage is an indicator of dust concentration. We have built two identical simple PM monitoring devices using Raspberry Pi 3 computer interfacing the PM sensor with Microchip’s MCP3002 ADC via SPI. The ADC is capable of more than 100 ksamples/s at 10-bit resolution. The Rpi3 was pulsing the sensor at 10Hz, digitizing and saving the data and sending the results wirelessly. Sensor’s output pulse shape was sampled with 10 microsecond time steps and saved, thus making offline analysis possible. A time jitter of output pulses can be observed and suggests a peak fitting as a better approach to the signal readout compared to the single sampling at a fixed time after pulse triggering We compared both methods. T2 - European Aerosol Coference EAC 2019 CY - Gothenburg, Sweden DA - 25.08.2019 KW - Aerosol KW - Low cost aerosol PM sensor KW - PM PY - 2019 AN - OPUS4-49581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Sturkenboom, I. T1 - Chinese paper in Persian manuscript: Preliminary results of a of a codicological, technological and scientific study N2 - In the 15th century, Persian manuscripts underwent significant and lasting changes. Possibly as a response to the import of tinted and gold-decorated paper from China, which was used for manuscript production in Greater Iran, Persian papers were also tinted and embellished with gold-decorated and marbled margins or frames. In a joint project between CSMC and the University of St Andrews, we aim to analyse papers and their decorations in Persian The analyses aim to determine the consistencies of papers, pigments and metals and the techniques used for their production and application. The support will be first described in its codicological characteristics such as dimensions, thickness, colour (expressed in colour coordinates), pattern left from the sieve (observed in transmitted light). The plant used as raw material in paper production will be studied by fibres analysis, while the sizing agents, the pigments, dyes and metals will be analysed by the application of several methods: in particular Reflectography, X-Ray Fluorescence and InfraRed, Raman and Visible Reflectance Spectroscopy. The results of the analyses will form an important resource for the material aspects of Persian manuscripts and be a starting point for establishing a first chronology of the materials and techniques used in Persian manuscript production. An example of the application of the techniques on the analysis of a fragment from a 15th c. Persian Manuscript will be provided. T2 - The Second International Seminar on Traditional Writing and Printing Materials (Fudan University) CY - Shanghai, Republic of China DA - 12.11.2019 KW - Persian manuscript KW - Chinese paper KW - Paper tinting KW - UV-VIS reflectance spectroscopy KW - XRF KW - ATR PY - 2019 AN - OPUS4-50131 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Ink for papyri, ink of papyrus: Recipes from the Arabic world N2 - Papyrus was in use in the Islamic world until the 11th century and few ink recipes collected from treatises about the art of the books are dedicated to this support. But papyrus was also burnt in order to obtain soot used as an ingredient for a particular type of ink (midād al-qarāṭīs). In this talk I will give an overview of the recipes – in particular those by ar-Rāzī –, their context and transmission in order to evaluate this double nature of papyrus, which is considered at the same time a writing support and a material to be recycled. Moreover, I will discuss what kinds of ink are most likely to be found, according to these literary sources, on Arabic manuscripts and documents written on papyrus and compare them to the typologies mentioned for paper and parchment. These results are the premises of a research project starting at the beginning of 2019, in which a number of dated fragments from several European institutions will be analysed with non-destructive techniques in order to establish a profile of the main writing media used in the early centuries of the Islamic Era. T2 - 29th International Congress of Papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Inks KW - Arabic recipes KW - Papyrus PY - 2019 AN - OPUS4-50158 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Fifty shades of black: Typologies and terminology of black inks in the light of new discoveries N2 - The identification of the materials constituting an artefact is the basis of any correct conservation project. For this reason (among others) in the last 50 years analytical techniques have been applied to the study of manuscripts. Unfortunately, the scientific investigation of Arabic books is still uncommon, focusing mainly on single case studies of illuminated manuscripts where the black media used to write the text is largely overlooked. This lack of knowledge prompted a recent research in which black ink recipes have been collected from written Arabic sources, their feasibility has been assessed, and some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, mostly non-invasive and non-destructive, in order to build a database of Arabic inks and their ingredients and to verify the detection limits of the equipment employed. Finally, the results were compared to the data collected from historical manuscripts. In this talk I will focus on the ink typologies and the terminology (ancient and modern) used to describe them. In particular I will highlight how even the modern classification fails to capture the variety encountered in both recipes and manuscripts, particularly in the light of recent discoveries. I will address especially the terminological and conceptual issues of mixed inks – in the form of carbon inks and tannins, of carbon and iron gall inks, and of carbon and metallic salts –, iron gall inks made without vitriol and iron gall inks made with sources of tannins different from gall nuts. T2 - First International Conference Oriental Manuscripts: Codicology and Conservation issues CY - Saint Petersburg, Russia DA - 04.12.2019 KW - Ink terminology KW - Codicology KW - Non destructive analytical techniques PY - 2019 AN - OPUS4-50159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Ink recipes from the islamic era: Texts, manuscripts, ink reproductions and scientific analyses N2 - Ink recipes can often be found in Arabic manuscripts. They may be included in treatises of diverse subjects – from handbooks for secretaries or calligraphers to books on arts and crafts, to alchemical and astrological essays. Recipes can also appear, with or without relation to the main text in the manuscript, in the form of lists or collections or even added in empty spaces as single entries. Why were these recipes written down? Were they used by the many professionals dealing with inks in their every-day work? Or were they part of the literary genre of adab with little or no practical application? To answer these questions a research project was set up: ink recipes have been collected from written Arabic sources, their feasibility has been assessed and some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, most non-invasive and non-destructive, and the results compared to the data obtained by the application of the same analyses on concrete manuscripts. The codicological characteristics of the manuscripts have also been studied. My aim in this talk is to show how such an interdisciplinary approach could be beneficial for the study of material culture. T2 - Broadening Horizons 6 CY - Berlin, Germany DA - 24.06.2019 KW - Inks KW - Arabic Recipes KW - Non destructive analytical techniques PY - 2019 AN - OPUS4-50160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - Analyses of decorated papers: Potential and preliminary results on persianate manuscripts from 15th – 17th centuries N2 - This talk will be divided into two parts. In the first part I will present the analytical techniques and the equipment used by the Centre for the Study of Manuscript Cultures that can be applied for the study of decorated papers. The analyses aim to determine the constituent materials of papers, pigments, dyes and metals and the techniques used for their production. I will focus in particular on the kind of information these techniques allow us to gather: through optical microscopy we conduct fibre analysis in order to identify the plant used as raw material in paper production while Reflectography, X-Ray Fluorescence and InfraRed, Raman and Visible Reflectance Spectroscopy are used to study the sizing agents, the pigments, dyes and metals. In the second part I will show some results obtained by the application of these techniques on a few Persianate manuscripts, dating between the 15th and 17th centuries, belonging to the corpus of Ilse Sturkenboom. T2 - Symposium Decorated Paper in Early Modern Islamic Cultures CY - Istanbul, Turkey DA - 23.11.2019 KW - XRF KW - UV-VIS Reflectance spectroscopy KW - Fibre analysis KW - Persian manuscripts KW - Chinese Paper KW - FTIR spectroscopy PY - 2019 AN - OPUS4-50161 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia T1 - The Interdisciplinary Alchemist: Reproduction and Study of Black Inks from the Islamicate World N2 - The identification of the materials constituting an artefact is the basis of any correct conservation project, for this reason (among others) in the last 50 years analytical techniques have been applied to the study of manuscripts. Unfortunately, the scientific investigation of Arabic books is still uncommon, focusing mainly on single case studies, often producing unclear results, especially for black inks. This lack of knowledge prompted a recent research in which black ink recipes have been collected from written Arabic sources on bookmaking, their feasibility has been assessed, and finally some of them have been reproduced. These samples were artificially aged and analysed through an array of analytical techniques, mostly non-invasive and non-destructive, in order to build a database of Arabic inks and their ingredients and also to verify the detection limits of the portable equipment employed. In this talk I will present some instances of how this approach can help textual criticism, for example in evaluating variants and determining the competence of authors and compilers. At the same time the research highlights how much this scientific work depends on textual studies, especially concerning the identification of ingredients. Moreover, I will focus on some of the problematics I faced both during the textual interpretation and the actual reproduction of the recipes and how they influenced the results of the scientific analyses. In particular I’ll look into the role played by the degree of purity of the components and the function (real and perceived) of some of the ingredients. T2 - International Medieval Conference 2019 CY - Leeds, UK DA - 01.07.2019 KW - Black Ink KW - Arabic Recipes KW - Interdisciplinary PY - 2019 AN - OPUS4-50114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Colini, Claudia A1 - Sturkenboom, I. T1 - Analyses of paper, tinting and illumination in persian manuscripts held in the Golestan Palace library N2 - In the 15th century, Persian manuscripts underwent significant and lasting changes. Possibly as a response to the import of tinted and gold-decorated paper from China, which was used for manuscript production in Greater Iran, Persian papers were also tinted and embellished with gold-decorated and marbled margins or frames. In a joint project between CSMC and the University of St Andrews, and in co-operation with the Golestan Palace Museum, we aim to analyse papers and their decorations in manuscripts in the holdings of the Golestan Palace Library. The analyses aim to determine the consistencies of papers, pigments and metals and the techniques used for their production and application. The support will be first described in its codicological characteristics such as dimensions, thickness, colour (expressed in colour coordinates), pattern left from the sieve (observed in transmitted light). The plant used as raw material in paper production will be studied by fibres analysis, while the sizing agents, the pigments, dyes and metals will be analysed by the application of several methods: in particular Reflectography, X-Ray Fluorescence and InfraRed, Raman and Visible Reflectance Spectroscopy. The results of the analyses will be published in an online database that will form an important resource for the material aspects of Persian manuscripts and be a starting point for establishing a first chronology of the materials and techniques used in Persian manuscript production. T2 - DFG workshop at Golestan Palace CY - Tehran, Iran DA - 07.04.2019 KW - Persian manuscripts KW - Chinese paper KW - Non destructive analytical techniques KW - Tinting KW - Gold PY - 2019 AN - OPUS4-50164 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Krom, I. A1 - Heikens, D. A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Baldan, A. T1 - CRMs for (semi-)VOCs in sorbent tubes N2 - EN 16516 sets the test method and requirements for the determination of emissions of Volatile Organic Compounds (VOCs) from building materials into indoor air. To address the quality control requirements for the class of semi-VOCs (SVOCs), VSL developed gaseous reference materials. A novel home-made dynamic gas mixture preparation system, operating according to ISO 6145-4 (continuous injection method), has recently been developed and validated. Thanks to the stable temperature control up to 100 oC, the system can prevent condensation of the SVOCs in air at indoor air concentration levels. The in-situ obtained SVOC gas standards can be sampled in sorbent tubes to obtain SVOC transfer standards. A study was performed to determine the optimal sorbent material and storage conditions. This study will be presented together with the results of the 2018 Round Robin test for emission test chamber measurements organised by BAM. Using the novel system, VSL prepared transfer standards with known amounts of VOCs and SVOCs for participants to evaluate their analytical performance. T2 - Emissions and Odours from Materials CY - Brussels, Belgium DA - 07.10.2019 KW - CRM KW - VOC transfer standards KW - Round robin test KW - Material emissions testing PY - 2019 AN - OPUS4-49423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietz, Georg T1 - Sieb und Filz - Entwicklungsgeschichtliche Meilensteine des Papiermaschinenbaus / der Papiermaschinenbespannungen N2 - Im Jahr 2019 jährt sich die Inbetriebnahme der ersten Papiermaschine in Deutschland zum 200. Male. Mit dem Vortrag wird eine Einführung in die Technologie der Maschinenpapierherstellung, samt entwicklungsgeschichtlicher Meilensteine gegeben. Es gilt die Produktvielfalt von Papier und die Gründe für die enormen Produktionssteigerungen bei der Papierherstellung aufzuzeigen. T2 - 27. Tagung des Deutschen Arbeitskreises für Papiergeschichte CY - Düren, Germany DA - 24.10.2019 KW - Papier KW - ZfP KW - Archäometrie PY - 2019 AN - OPUS4-50633 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietz, Georg T1 - Papieranalysen für die kunstgeschichtliche Forschung N2 - Wasserzeichen und Papierstrukturen können einen wesentlichen Beitrag bei der Analyse von Kunstobjekten auf Papier darstellen. An Fallbeispielen aus der gutachterlichen Praxis und Forschungsprojekten der Vergangenheit sollen die Möglichkeiten der Papier- und Wasserzeichenforschung bei Datierungen und Authentizitätsprüfungen demonstriert werden. T2 - PTS-Workshop in Heidenau zu Thema: Materialwissenschaftliche Untersuchungsmethoden zur Charakterisierung und Authentifizierung von Dokumenten und Kunstwerken auf Papier CY - Dreden-Heidenau, Germany DA - 07.11.2019 KW - Papier KW - Fälschungserkennung KW - ZfP PY - 2019 AN - OPUS4-50634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerrits, Ruben A1 - Pokharel, R. A1 - Breitenbach, Romy A1 - Radnik, Jörg A1 - Wirth, R. A1 - Schuessler, J. A. A1 - Benning, L. G. A1 - von Blanckenburg, F. A1 - Gorbushina, Anna A1 - Feldmann, Ines T1 - Olivine weathering by the genetically amenable rock-inhabiting fungus Knufia petricola A95 N2 - In arid sun-exposed environments, rock-inhabiting fungi dominate microbial communities on rock surfaces. Fungi are known to enhance rock weathering, although the exact mechanisms are not completely understood. These natural processes can be simulated by reproducible experimental systems. Particularly attractive are genetically amenable rock-weathering fungi, where certain traits can be knocked-out to identify weathering-relevant functions. Here, we studied the effect of the rock-inhabiting fungus Knufia petricola A95 and its melanin-deficient mutant (ΔKppks) on the weathering of a Fe-bearing olivine. We examined the olivine dissolution kinetics and looked at the olivine-fungus interface. For the former we inoculated olivine powder with the fungus in batch and mixed flow reactors and analysed the medium solution by ICP-OES, for the latter biofilm-covered olivine sections from flow-through reactors were analysed by FIB-TEM. In general olivine dissolution was lower when olivine was incubated without fungi: the abiotic olivine dissolution rates were lowest and the surface of the abiotically reacted olivine sections showed no etching. Various chemical analyses show Fe (oxyhydr)oxide precipitation on top of the abiotically reacted olivine, indicating its role in inhibiting olivine dissolution. Both the wild type (WT) and ΔKppks solubilised and bound significant amounts of Fe released by olivine dissolution. Fe (oxyhydr)oxide precipitation was thus reduced, explaining the enhanced olivine dissolution in their presence. Particularly efficient at preventing Fe precipitation were attached WT cells: the inhibition of olivine dissolution almost completely disappeared. The attachment capacity of the WT is most likely caused by the production of WT-specific extracellular polymeric substances. Our presented experimental systems allowed the precipitation of Fe (oxyhydr)oxides and included a rock-inhabiting fungus and thus simulated weathering processes relevant to natural ecosystems. T2 - ISEB 2019 CY - Potsdam, Germany DA - 23.09.2019 KW - Olivine KW - Weathering KW - Fungus PY - 2019 AN - OPUS4-49585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, P. T1 - Archaeometric analysis of inks from Coptic Manucripts N2 - Understanding the technological evolution of inks from Coptic Manuscripts. T2 - III International PAThs Conference CY - Rome, University of La Sapienza, Italy DA - 25.02.2019 KW - Archaeometry PY - 2019 AN - OPUS4-48037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, Paola T1 - Archaeometric analysis of Egyptian inks from Late Antiquity N2 - Presentation of the results obtained on a corpus of Egyptian papyri from Late Antiquity T2 - Research Showcase: studying Greco-Roman Egypt CY - University of Basel, Switzerland DA - 26.09.2019 KW - Ink KW - Archaeometry KW - Manuscripts KW - Coptic PY - 2019 AN - OPUS4-49969 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, Paola T1 - Análisis arqueométrico de tintas N2 - Análisís arquéometrico de tintas de manuscritos Egipcios T2 - IX Jornadas de Papirología CY - Abadía de Montserrat, Spain DA - 08.07.2019 KW - Coptic KW - Archaeometry KW - Ink KW - Manuscripts PY - 2019 AN - OPUS4-49970 LA - spa AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, Paola T1 - Archaeometric analisis of Egyptian inks from Late Antiquity N2 - Archaeometric analisis of Egyptian inks from Late Antiquity: presentation of the results obtaine on a curpus of literary and documentary manuscripts. T2 - International congress of papyrology CY - Lecce, Italy DA - 28.07.2019 KW - Coptic KW - Archaeometry KW - Ink KW - Manuscripts PY - 2019 AN - OPUS4-49971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Microbiology / biofilms in material research and testing N2 - In the modern world there is an increased understanding that design and performance monitoring of materials have to be tested in connection to chemical, physical and (micro)biological challenges. A systematic study on how biofilms interact with materials and what could be done to engineer biofilms and/or materials in order to maximize the resistance of the material (surface) or the resistance the biofilm-modified material (bulk) is in strong need. In the Department “Materials and the Environment” of the BAM new experimental platform is being developed. With the help of different type of device for high throughput and microbiologically-controlled environment simulation we establish a new approach to clarify the mechanisms of biofilm/material interactions. Despite the focus on fundamental research, the main results of this project proposal will be transferable into material technology and construction chemistry and will influence the development of standardization in this topic. As the interactions of biofilms and materials have implications for most constructions as well as climate change, the results of the research generates additional value. T2 - Initialgespräch - DFG-Forschungsgruppe "Mikrobiologie/Biofilme" CY - Karlsruhe, Germany DA - 14.11.2019 KW - Biofilm KW - Microbiology KW - Black fungi KW - Solar panel PY - 2019 AN - OPUS4-50199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life on the rocks - Black fungi from biofilms on material-atmosphere interface N2 - Interface between the atmosphere and mineral substrates is the oldest terrestrial habitat. Morphologically simple microbial biofilms were the first settlers on these inhospitable surfaces at times when the Earth was inhabited only by microorganisms and the solid substrates represented only by natural rock surfaces i.e. lithosphere. Miniature, self-sufficient microbial ecosystems continue to develop on subaerial (i.e. air-exposed) solid surfaces at all altitudes and latitudes where direct contact with the atmosphere and solar radiation occurs – on rocks, mountains, buildings, monuments, solar panels. All these sub-aerial biofilms develop under fluctuating and hostile conditions – and thus frequently harbour stress-tolerant black fungi inherently able to cope with the stresses of bright sunlight and constantly changing atmospheric conditions. Black fungi – a polyphyletic group of Ascomycetes– accumulate the dark pigment DHN melanin, diverse carotenoids and mycosporines in their cells and thus successfully colonise sunlight-flooded habitats from phyllosphere to rock surfaces. Various chemical and physical extremes and fluctuating environments belong to the challenges effectively mastered by black fungi. In our laboratory we isolate novel black fungi from man-made habitats like building materials and solar panels. Using Knufia petricola A95 as a model we conduct experiments to clarify interactions of black fungi with inorganic substrates. We use available mutants to determine the functional consequences of changes in the outer cell wall envelopes – from excreted EPS to layers of protective pigments. A genetic toolbox to manipulate this Chaetothyriales representative is in further development. Our long-term goal is to understand the fundamental mechanisms how black fungi are able (i) to adhere to dry atmosphere-exposed surfaces, (ii) to survive multiple stresses and (iii) to change the underlying substrates including rocks. T2 - International Symposium on Fungal Stress (ISFUS) CY - São José dos Campos, Brazil DA - 19.05.2019 KW - Subaerial biofilm KW - Melanins KW - Carotenoids KW - Knufia KW - Mineral weathering PY - 2019 AN - OPUS4-50200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life on the rocks and other hard surfaces N2 - The story of how black fungi survive harsh conditions on sun-exposed desert rocks and material surfaces is fascinating. In the presentation examples of how knowledge of these organisms can be of practical value (e.g., in biodeterioration studies, such as on stone markers in cemeteries) would be given. Among other stories, the example of how roof tiles amended with a titanium oxide layers as a biocide actually selected for the black fungi will be told. A hypothesis about how these organisms would likely be found on solar panels and some early BAM work in that area will be presented. This then brings the connection to a study ripe for investigation in North Carolina. The talk presents the development of a study aiming at deciphering the influence of microbial biofilm formation on the energy conversion efficiency of solar photovoltaic panels or modules at two facilities (one facility under the impact of high intensity of animal agriculture and high deposition of ammonia from atmosphere and the other with low animal agriculture and lower atmospheric ammonia deposition) in North Carolina. The main hypothesis of the study is that microbial biofilm formation on solar photovoltaic panels will lead to significant decreases in energy conversion efficiency of solar photovoltaic modules and biofilm formation will also be accelerated by high ammonia concentration in the ambient atmosphere and high nitrogen deposition. T2 - Dr. Michael D. Aitken Symposium CY - Chapel Hill, NC, USA DA - 08.11.2019 KW - Black fungi KW - Solar panel KW - Biofilm PY - 2019 AN - OPUS4-50125 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - Paper: history, manufacture, properties N2 - The lecture traces the origins of paper, the manufacture and the spread from China to the Middle East and Europe. Though technological progress considerably affected each step of the manufacture of paper, the essence of the invention remains unchanged until today. The process of manufacturing handmade paper can be divided into a number of steps: - choosing the raw material (e.g. cellulose from wood, cotton, rags) - beating and grinding the fibres into small pieces - producing a liquid pulp of the desired texture - treating the pulp with various additives - filling the pulp suspension into a paper mould - draining the water - pressing and drying to get the actual sheet - various post-production treatments We will see how the manufacturing process is reflected in the properties of the paper and its degradation. A special attention will be paid to the instrumental analysis for identification of the paper types. Also watermark play an important role in the studies of the manuscripts. A short overview will be offered at the ends of the lecture. T2 - Summer School Manusciences 19 CY - Frejus, France DA - 10.03.2019 KW - Material science KW - Cultural heritage PY - 2019 AN - OPUS4-48140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - Zerstörungsfreie Prüfverfahren zur Authentifizierung von Manuskripten und Zeichnungen – Möglichkeiten und Grenzen N2 - Untersuchungen von Zeichnungen und Manuskripten mit zerstörungsfreien Methoden haben in den letzten Jahren enorm zugenommen. Die nicht-invasiven Analysen ermöglichen Informationen zur Herkunft, zum Herstellungsprozess und möglicherweise zum Alter (direkte Dating nicht möglich, Ausnahme: Papierstruktur, Wasserzeichen). Die zerstörungsfreien Analysen können Rückschlüsse auf mögliche Fälschungen geben, sind neben den offensichtlichen Vorteilen jedoch auch mit einzelnen Limitierungen behaftet. Der Vortrag soll anhand einiger Fallbeispiele die Möglichkeiten aber auch Grenzen bei der zerstörungsfreien (mobilen) Auffindung von Fälschungen aufzeigen. T2 - PTS Workshop"Materialwissenschaftliche Untersuchungsmethodenzur Charakterisierung und Authentifizierung von Dokumenten und Kunstwerken auf Papier" CY - Heidenau, Germany DA - 07.11.2019 KW - ZfP KW - Authentifizierung KW - Papier PY - 2019 AN - OPUS4-49666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver A1 - Wintermann, C. A1 - Dietz, Georg A1 - Golle, U. A1 - Ketelsen, T. A1 - Melzer, C. T1 - Braune Tinten – Geschichte und Materialität N2 - Eine Vielzahl unterschiedlicher Materialien findet für die Gestaltung von Zeichnungen Verwendung. So sind es insbesondere „braune Tinten“, welche die Zeichnungen dominieren. Der Vortrag möchte zunächst einen kurzen Überblick über die Terminologie und die Kunsttechnologie farbiger Tinten geben, um den Kosmos dieser Vielfältigkeit und auch deren Vergänglichkeit zu illustrieren. Der zweite Teil des Vortrags ist dann den sogenannten Bistertinten und deren analytischen Nachweisen gewidmet. Es handelt sich um Zeichentinten, die aus den wasserlöslichen Bestandteilen von Kaminruß gewonnen werden. Die farbliche Bandbreite reicht von gelb-orange bis braun. Zuweilen wurden diese Tinten mit weiteren Pigmenten versetzt, um eine bestimmte Farbtiefe zu erzielen. T2 - 29. Treffen der Grafikrestauratoren CY - Weimar, Germany DA - 25.10.2019 KW - Zerstörungsfreie Prüfung KW - Zeichenmaterialien KW - Archäometrie PY - 2019 AN - OPUS4-49731 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Adam, Christian A1 - Stolle, Dirk A1 - Spanka, M. A1 - Auer, G. T1 - Thermochemical treatment of waste products from iron and steel production N2 - This presentation summarizes the development of a novel thermochemical process for recycling of zinc and lead-bearing wastes (blast furnace sludge and electric arc furnace dust) that accumulate during iron and steel production. T2 - European Metallurgical Conference 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Blast furnace sludge KW - Electric arc furnace dust KW - Recycling KW - Selective chlorination KW - Zinc PY - 2019 AN - OPUS4-48364 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Spanka, M. A1 - Stolle, Dirk A1 - Adam, Christian A1 - Auer, G. T1 - Rückgewinnung von Zink aus Stahlwerksstäuben durch gemeinsame Behandlung mit chloridhaltigen Reststoffen N2 - Dieser Vortrag beschreibt die Entwicklung eines neuen chemischen Verfahrens, das in einem Kooperationsprojekt zwischen der Bundesanstalt für Materialforschung und -prüfung (BAM) und der Ferro Duo GmbH entwickelt wird. Mit dem entwickelten Verfahren soll es ermöglicht werden, schwermetallhaltige Filterstäube und -schlämme, die als Abfälle während der Produktion von Roheisen und Rohstahl anfallen und die derzeit größtenteils deponiert werden, zu recyceln und die darin enthaltenen Wertstoffe (v.a. Eisen, Kohlenstoff und Zink) wieder in den Rohstoffkreislauf zurückzugeben. Dies wird durch eine Chlorierung der in den Filterstäuben und -schlämmen enthaltenen Schwermetalloxiden erreicht, die bei Temperaturen zwischen 650 und 1100 °C in Form von Schwermetallchloriden verdampft und so selektiv separiert werden. Erste experimentelle Ergebnisse zeigen, dass die Gehalte an Schwermetallen wie Zink, Blei und Cadmium um bis zu 99,7% reduziert werden können und die thermochemisch behandelten Filterstäube und -schlämme durch das Verfahren in sekundäre Rohstoffe für die Roheisenproduktion umgewandelt werden können. T2 - Berliner Recycling- und Rohstoffkonferenz 2019 CY - Berlin, Germany DA - 11.03.2019 KW - Zink KW - Recycling KW - Gichtgasschlamm KW - Elektroofenstaub KW - Ressourcenrückgewinnung PY - 2019 AN - OPUS4-47524 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai A1 - Mohr, Gunther A1 - Altenburg, Simon A1 - Ulbricht, Alexander A1 - Seeger, Stefan T1 - Prozessmonitoring für die additive Fertigung: Entwicklungen an der BAM N2 - Das Prozessmonitoring stellt einen wichtigen Baustein für eine Qualitätssicherung additiv gefertigter Bauteile dar, insbesondere bei kleinen Losgrößen. Der Vortrag zeigt einen Überblick aktueller Entwicklungen der BAM im Bereich des Prozessmonitorings für das Laserstrahlschmelzen (laser powder bed fusion) metallischer Werkstoffe. Durch Vergleich mit der Referenzmethode Computertomografie wird am Beispiel der thermografischen Verfahren gezeigt, wie relevante Defekte in Bauteilen detektiert werden können und Einsatzpotenziale sowie Limitierungen aufgezeigt. T2 - Forum Additive Fertigung Rheinland-Pfalz CY - Ludwigshafen, Germany DA - 07.11.2019 KW - Optische Tomografie KW - Additive Fertigung KW - Prozessmonitoring KW - Thermografie PY - 2019 AN - OPUS4-49958 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Marie A1 - Vogel, Christian A1 - Adam, Christian A1 - Stephan-Scherb, Christiane A1 - Hecht, Lutz T1 - Novel approaches to Sc species investigation in bauxite residues by x ray absorption near edge structure spectroscopy N2 - In a rapidly evolving world, the demand on raw materials is increasing steadily and many technologies are dependent on a secure supply of hi-tech metals. Recently, scandium (Sc) has attracted attention since its use in high strength Al-alloys and solid-oxide-fuel-cells strongly improves the performance of those materials. The element Sc is not exceptionally rare but quite resistant to geochemical enrichment processes, it is scarcely found enriched to high concentrations and is recovered as a by-product. Since Sc enrichment in Greek bauxite residues was shown by Ochsenkühn-Petropoulou et. al (1994), intensive research on this material and development of efficient Sc-recovery methods is ongoing. This study investigates Sc-bearing species in bauxite residues from alumina production. It aims to provide direct evidence about the Sc-speciation’s in those secondary resources and tries to find the link to speciation’s in primary resources, e.g. bauxites and laterites. Therefore, Sc K edge XANES (X-ray absorption near edge structure) spectroscopy is performed using synchrotron radiation to determine the presence of certain Sc-components and distinguish between adsorbed and chemically bonded Sc as was shown for lateritic deposits in Australia by Chassé et al. 2016. For comparison, reference standards of Sc-bearing and Sc-adsorbed species are synthesized. Indirect inferences from leaching behavior of bauxites, in cases supported by analyses with LA-ICP-MS, suggest Sc to be associated with either iron- or aluminum phases (Vind et al. 2017); (Suss et al.). It remains unclear how different primary materials influence Sc-speciation in the bauxite residue. Therefore, a comparison between different European bauxite residues is made in this study. The investigations should help to understand Sc chemistry and behavior in different primary and secondary materials and provide fundamentals for metallurgical processing. The research is incorporated in the SCALE project (GA No. 730105) funded by EU Horizon 2020 research and innovation program. T2 - DMG Tagung GeoMünster CY - Westfälische Wilhelms-Universität Münster, Germany DA - 22.09.2019 KW - Scandium KW - Bauxite Residue KW - Red Mud KW - XANES PY - 2019 AN - OPUS4-49389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - Aktuelle Ringversuche der BAM zu VOC und Gerüchen N2 - Ein Ringversuch ist eine Methode der externen Qualitätssicherung für sowohl Messverfahren als auch die Eignung von Mess- und Prüflaboratorien. Dabei werden möglichst identische Proben mit identischen Verfahren oder mit unterschiedlichen Verfahren untersucht. Die Teilnahme an Ringversuchen ist für alle akkreditierten Laboratorien ein wesentlicher Baustein der institutsinternen und -externen Qualitätssicherung. Je mehr Faktoren Einfluss auf das Endergebnis haben können, desto wichtiger ist es diese Faktoren zu kennen und deren Einflüsse durch weitestgehende Vergleichbarkeit der Messverfahren zu minimieren. Für die Bewertung von Emissionen aus Bauprodukten haben sich Emissionsmess-kammer-Untersuchungen als Messverfahren etabliert. Um den Geruch auch für Innenraumanwendungen bewertbar zu machen sind in den letzten Jahren erste Normen entstanden (z. B. DIN ISO 16000-28 und VDI 4302-1). Um die Eignung dieser Normen und deren Anwendung zu untersuchen sind seit 2012 nunmehr 3 Ringversuche der BAM auch zum Thema Geruch durchgeführt worden. Die bislang durchgeführten Ringversuche mit dem Ziel der Geruchsbewertung wiesen Standardabweichungen von ca. 24 bis 30 % um den jeweiligen Mittelwert auf und wiesen somit ähnliche Werte auf, die auch bei den VOC-Vergleichen ermittelt wurden. Diese Entwicklungen werden hier aufgezeigt. T2 - 26. WaBoLu-Innenraumtage CY - Berlin, Germany DA - 20.05.2019 KW - Geruch KW - Ringversuch KW - Bauprodukte KW - Emission KW - Emissionskammer PY - 2019 AN - OPUS4-49237 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - Kunstgüter in Vitrinen: was helfen Materialuntersuchungen gemäß BEMMA-Schema? N2 - Moderne Vitrinen sollen gleichzeitig eine hohe Dichtigkeit und die Abwesenheit jeglicher Fremdstoffe in den Vitrinen gewährleisten. Diese Anforderungen sind zeitgleich kaum erfüllbar, da es emissionsfreie Materialien (vor allem Kleb- und Beschichtungsstoffe) nicht gibt. Um die potentiellen Emissionen zu minimieren wurde ein Messverfahren entwickelt, welches inzwischen als BEMMA-Schema (Bewertung von Emissionen aus Materialien für Museumsausstattungen) in die Museumswelt Einzug genommen hat. Die erfolgreiche Bewertung der für den Bau verwendeten Materialien gemäß BEMMA-Schema resultiert nicht in einer emissionsfreien Vitrine, sondern soll bei der Auswahl geeigneter Materialien zur Herstellung möglichst emissionsarmer Vitrinen helfen. Konkrete handwerkliche Durchführungen beim Bau, Dichtheits-anforderungen, wie auch die Aufstellbedingungen (Umgebung der Vitrine) beeinflussen die Emissionscharakteristik der fertigen Vitrine in der Praxis. Eine saubere Vitrine hilft nichts in einer belasteten Umgebung oder auch bei emittierenden Exponaten. Inzwischen liegen Erfahrungen mit dem Schema seit 2012 vor. Der Messablauf sieht vor, dass von den Materialien kleine Muster mit der Mikrokammer (Markes) innerhalb von 2 Tagen untersucht werden. Dabei wird mit Silikagelkartuschen auf Ameisen- und Essigsäure, mit DNPH auf Aldehyde und Ketone und mit Tenax® sowohl auf VOC als auch für die spezifische Oxim-Analytik die Abluft der Mikrokammern untersucht. Die Bewertungskriterien basieren auf den Ergebnissen einer Vorstudie mit ca. 150 verschiedenen Produkten im Zeitraum 2010 bis 2012. T2 - 12. Fachkongress der Arbeitsgemeinschaft ökologischer Forschungsinstiute (AGÖF) CY - Hallstadt (Bamberg), Germany DA - 17.10.2019 KW - Museum KW - Emission KW - Bauprodukte KW - BEMMA KW - Vitrinen PY - 2019 AN - OPUS4-49327 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - Selection of low emittiong material for the construction of display cases based on the BEMMA procedure N2 - Museums worldwide are equipped with different display cases. Exhibit display cases should protect cultural objects from dust as well as from mechanical and physical damage. To ensure a stable climate inside the display cases, a low air exchange rate is maintained. Typically air exchange rates are often smaller than 0.1 d 1, which can result in rising concentrations of potential harmful immissions inside of the display cases due to emissions from materials. Especially high concentrations of organic acids, which can emit from e.g. sealing materials, can produce damage of cultural objects. In 2012 BAM introduced a procedure witch is called: BEMMA-Scheme (Bewertung von Emissionen aus Materialien für Museumsausstattungen) which stands for: “Assessment of Emissions from Materials for Museum Equipment”. Micro chambers are used for VOC emission tests of display case construction materials, e.g. textiles, plastics, sealing material, coatings and others. Each sampling procedure is carried out in duplicate. Emissions like formic acid, acetic acid, formaldehyde and oximes are excluded and the sum of emissions of VVOCs, VOCs and SVOCs is limited. For a positive assessment all listed criteria must be fulfilled; otherwise the display construction material fails the BEMMA scheme. The BEMMA scheme is not a guarantee for an emission free display case, but a necessary requirement for the choice of suitable materials for emission and immission reduced display cases. T2 - Materials Testing Symposium CY - New York City, USA DA - 06.11.2019 KW - Museum KW - Emission KW - Dispay case KW - BEMMA KW - VOC PY - 2019 AN - OPUS4-49589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Stand der Technik der Emissionsmessungen für das Umweltkompartiment Luft N2 - Der mitteleuropäische Mensch hält sich 80 – 90 % der Zeit in Innenräumen auf. Je nach Aktivität atmet er 10 – 20 m³ bzw. 12 - 24 kg Luft täglich, das ist weit mehr als das Doppelte der Summe an Essen und Trinken. Die technischen Voraussetzungen für die Bestimmung von Emissionen aus Bauprodukten in die Luft liegen vor – harmonisierte horizontale Prüfnorm EN 16516. Es dürften mittlerweile zig-tausende Emissionsdatensätze vorliegen. Defizite gibt es bei der Kennzeichnung zur Unterscheidung emissionsarmer und emissionsreicher Produkte, die bestehende CE-Kennzeichnung ist unvollständig, ersatzweise gibt es nationale Regelungen. Gerade bei modernen, dichten Bauten mit geringem natürlichen Luftwechsel sind hohe Schadstoffkonzentrationen zu erwarten, wenn nicht emissionsarme Materialien und Produkte zum Einsatz kommen. T2 - Eurolab-Workshop Anforderungen an Bauprodukte - Umweltrelevante Aspekte sowie die gesamtheitliche Bewertung CY - Berlin, Germany DA - 11.11.2019 KW - Gesundheit KW - Emissionsmessungen KW - Bauprodukte KW - Luft KW - Bauproduktenverordnung PY - 2019 AN - OPUS4-49596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Schadstoffe im Innenbereich – Fachhandel-, Baumarkt-, Bioprodukte: Nicht deklarierte Emissionen versus Verwendbarkeit - Eine Qual der Wahl! N2 - Es lässt sich feststellen, dass eine Vielzahl unterschiedlicher flüchtiger organischer Verbindungen aus Bauprodukten freigesetzt werden kann. Hierbei gibt es in den meisten Bauproduktgruppen sowohl emissionsarme als auch emissionsreiche Produkte. Manche Verbindungen sind produktgruppenspezifisch; so werden beispielsweise Siloxane aus Silikondichtmassen freigesetzt, andere Verbindungen sind eher unspezifisch wie Formaldehyd und Essigsäure, die aber in unterschiedlichen Konzentrationen aus einer Vielzahl von Produkten abgegeben werden und zu den am häufigsten emittierten Verbindungen zählen. Es ist darauf hinzuweisen, dass VOC-Analytik und Gerüche im Allgemeinen keinen Zusammenhang zeigen. Gerade bei modernen, dichten Bauten mit geringem natürlichem Luftwechsel sind hohe Schadstoffkonzentrationen zu erwarten, wenn nicht emissionsarme Materialien und Produkte zum Einsatz kommen. T2 - AIBAU 2019 CY - Aachen, Germany DA - 08.04.2019 KW - Innenraum KW - Luftschadstoffe KW - Bauprodukte KW - Emission PY - 2019 AN - OPUS4-47924 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Stofffreisetzung aus Sportböden auf Kunststoffbasis N2 - Dem Fachbeirat Bodenuntersuchungen des BMBF/UBA wurden Ergebnisse aus BISp-Forschungsvorhaben zur Untersuchung der Stofffreisetzung aus Sportböden auf Kunststoffbasis sowie zur Modellierung des Schadstofftransfers auf dem Pfad Boden-Grundwasser vorgestellt. Dabei wurde auch auf die derzeitigen gesetzlichen Regelungen auf EU Ebene und die vorhandenen Anforderungen in der Normung eingegangen. Der verbliebene Forschungsbedarf wurde aufgezeigt und dabei auch die Problematik der Bildung von Mikroplastik im Zusammenhang mit Sportböden thematisiert. T2 - 40. Sitzung des Fachbeirates für Bodenuntersuchungen CY - Dessau, Germany DA - 13.06.2019 KW - Sportböden auf Kunststoffbasis KW - Freisetzung und Transfer von Schadstoffen PY - 2019 AN - OPUS4-50021 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, Rene A1 - Szuppa, Tony T1 - Monitoring of soil-like materials for potential reuse N2 - Paragraphs 6 to 8 of the proposed amendment to the German Federal Soil Protection and Contaminated Sites Ordinance contain new requirements regarding the application of soil-like material outside of a rootable soil layer. For example, it is intended to enable reusing of soil-like materials containing regulated substances in concentrations between the single and double precautionary values (PV), provided that the limit values for the eluate are complied with. The aim of a running project (funding code UFOPLAN 3716 74 203 0, German Federal Environmental Agency) is to fill data deficits for soil-like materials which meet the above-mentioned criteria to promote circular economy and conservation of natural resources. Different soil-like materials of various origin (for example dredged material, banquet peeling material, urban and meadow soils) are considered with a special focus on PAHs. A major challenge in sample acquisition is the relatively narrow target range of the PAH content between 3 and 6 mg/kg dm considering a high measurement uncertainty at this concentration level. The contents of PAHs, heavy metals and other inorganic elements in solid matter are determined following established standards. In addition, the soil-like materials are characterized concerning particle size, pH, conductivity, SOM, TOC and carbonate content. To determine the eluate concentration, column tests according to DIN 19528 and batch tests according to DIN 19529 at a liquid/solid ratio (L/S) of 2 l/kg and 10 l/kg are performed comparatively. The results show that the new requirements of the planned amendment to the Federal Soil Protection and Contaminated Sites Ordinance certainly opens additional possibilities for reuse of soil-like materials. Even most soil-like materials within 2-3 x PV comply with the eluate value for PAH (0.2 μg/l) both in the batch test and in the column test at L/S 2 l/kg. Selected inorganic substances lead to similar evaluations. Therefore, the application of such soil-like materials outside of rootable soil layers would be possible. Previously, those materials were often used for landfill construction. In the future, a utilization in the adjacent environment by backfilling, recultivation, renaturation, composting or landscaping would be conceivable. T2 - AquaConSoil 2019 -Sustainable Use and Management of Soil, Sediment and Water Resources CY - Antwerp, Belgium DA - 20.05.2019 KW - Soil-like materials KW - Utilization KW - Ordinance on Contaminated Sites and Soil Protection KW - PAH PY - 2019 AN - OPUS4-50022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, Rene A1 - Szuppa, Tony T1 - Erweiterung der Verwertungsmöglichkeiten von Bodenmaterialien auf der Grundlage der Novelle der BBodSchV N2 - Boden und Steine sind mit jährlich etwa 140 Mio t der mengenmäßig größte Abfallstrom in Deutschland. Bodenmaterial kann in Abhängigkeit seiner vorherigen Nutzung oder Herkunft mit Schadstoffen belastet sein. Seine weitere Verwertungsmöglichkeit hängt nicht nur vom Schadstoffgehalt im Feststoff, sondern auch von der Mobilisierbarkeit dieser Stoffe ab. Die Paragraphen 6 bis 8 der vorgesehenen Novelle der BBodSchV enthalten neue Vorgaben hinsichtlich des Auf- und Einbringens von Bodenmaterial unterhalb oder außerhalb einer durchwurzelbaren Bodenschicht (4. Referentenentwurf Mantelverordnung, Stand: 06.02.2017). Es soll die Möglichkeit eingeräumt werden, Bodenmaterialien mit Feststoffgehalten von regulierten Stoffen bei Überschreitung des Vorsorgewertes einer weiteren Verwertung zuzuführen unter der Voraussetzung, dass die Eluatwerte eingehalten werden. Für die Auswirkung dieser neuen Regelungen auf die Verwertung von Bodenmaterialien bestehen bisher noch Datendefizite besonders für organische Stoffe. Durch die Umstellung des Elutionsverfahrens von einem W/F von 10 l/kg (bisherige Regelung in der LAGA M 20) auf ein W/F von 2 l/kg bestehen zusätzliche Unsicherheiten im Hinblick auf die Einstufung von Bodenmaterialien zu Verwertungszwecken. Im Rahmen eines UFOPLAN-Projektes (FKZ 3716 74 203 0) wurden unterschiedliche Bodenmaterialien verschiedenen Ursprungs (z.B. Baggergut, Bankettschälgut, Stadt- und Auenböden, Bergematerial) mit besonderem Fokus auf PAK untersucht. Von den unter die Kriterien fallenden, ausgewählten Bodenmaterialien wurden Feststoffgehalte, TOC-Gehalte sowie die Eluatwerte aus Säulenversuchen nach DIN 19528 und Schüttelversuchen nach DIN 19529 bei einem Wasser-/Feststoffverhältnis (W/F) von 2 l/kg und 10 l/kg ermittelt und gegenübergestellt. Mit den neuen und auch mit Auswertung vorhandener Daten kann hinsichtlich PAK gezeigt werden, dass mit Verabschiedung der neuen Regelungen sich zusätzliche Verwertungsmöglichkeiten von Bodenmaterialien außerhalb der durchwurzelbaren Bodenschicht eröffnen und deren Deponierung vermieden werden kann. Analysen zu anorganischen Schadstoffen wurden parallel miterfasst und ausgewertet. T2 - Jahrestagung der Deutschen Bodenkundlichen Gesellschaft CY - Bern, Switzerland DA - 24.08.2019 KW - Bodenmaterial KW - Verwertung KW - BBodSchV KW - PAK PY - 2019 AN - OPUS4-50023 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, Rene A1 - Szuppa, Tony T1 - Verwertung von Bodenmaterialien - Ergebnisse aus dem UFOPLAN-Vorhaben und Transfer der Ergebnisse N2 - Dem Fachbeirat Bodenuntersuchungen des BMBF/UBA wurden Ergebnisse zum UFOPLAN-Forschungsvorhaben „Monitoring zur Verwertung von Bodenmaterial“ vorgestellt. Die potentielle Auswirkung der neuen Regularien in der geplanten Novelle der BBodSchV (4. Referentenentwurf der Mantelverordnung) auf die Erweiterung der Verwertungsmöglichkeiten von Bodenmaterialien wird aufgezeigt. Probleme des Umgangs mit der analytischen Messunsicherheit im Grenzwertbereich und mit der Vergleichbarkeit der zugelassenen Elutionsverfahren werden diskutiert. T2 - 40. Sitzung des Fachbeirates für Bodenuntersuchungen CY - Dessau, Germany DA - 13.06.2019 KW - Bodenmaterial KW - Verwertung KW - BBodSchV KW - PAK KW - Elutionsverhalten PY - 2019 AN - OPUS4-50018 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kayser, Y. A1 - Pollakowski-Herrmann, Beatrix A1 - Hönicke, P. A1 - Friese, Carmen A1 - Seeger, Stefan A1 - Cara, E. A1 - Boarino, L. A1 - Gianotti, V. A1 - Laus, M. A1 - Beckhoff, Burkhard T1 - AEROMET – Traceable and reliable chemical analysis of aerosols by X-ray spectrometry N2 - Traceable and reliable chemical element analysis of aerosols by X-ray spectrometry was investigated using aerosol samples from field campaigns which have been measured in the GIXRF-beamline at BESSY. The reference-free XRF approach allows for a traceable analysis of the mass deposition. Traceable quantification by means of XRF can be transfered to benchtop instrumentation used in the laboratory Chemical and dimensional analysis of deposited aerosol allows for a comprehensive analysis of aerosols, e.g. for toxicity assessment and determination of the source The folowing elements could be identified and quantified in the field samples: Al, Si, P, S, Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, Rb, Sr, Y, W, Pb. T2 - European Aerosol Conference EAC 2019 CY - Gothenburg, Sweden DA - 25.08.2019 KW - TXRF KW - Element mass concetration KW - Ambient aerosol KW - Cascade impactor PY - 2019 AN - OPUS4-49583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kjaervik, Marit A1 - Dietrich, P. A1 - Thissen, A. A1 - Schwibbert, Karin A1 - Brown, J. A1 - Hardie, K. A1 - Unger, Wolfgang T1 - Model systems and sample preparation for surface characterisation of bacteria and biofilms by near-ambient pressure XPS N2 - Bacterial samples are typically freeze dried or cryo-prepared prior to XPS analysis to allow for measurements in ultra-high vacuum (UHV). The sample environment in the near-ambient pressure (NAP) XPS instrument EnviroESCA allows for measurements in up to 15 mbar water vapor, thus, sample preparation is no longer restricted to UHV-compatible techniques. For instance, biofilms grown in medium can be transferred directly from the medium to the measurements chamber, maintaining a humid environment throughout the measurements. Considering the complexity of bacterial samples, sample preparation must be carefully considered in order to obtain meaningful and reproducible results. In this talk, various strategies for sample preparation of bacteria and biofilms for NAP-XPS measurements will be discussed. Model systems of planktonic bacteria, artificial biofilms resembling the exopolysaccharide matrix and biofilms have been characterised in various conditions. The stability and homogeneity of the samples was assessed by monitoring the C1s core level peak at different sample locations. The quality of the XPS-spectra is also influenced by the gas environment, which will be exemplified by core level spectra of P. Fluorescens acquired in air, water vapor and ultra-high vacuum. T2 - 18th European conference on applications of surface and interface analysis (ECASIA) CY - Dresden, Germany DA - 15.09.2019 KW - NAP-XPS KW - Biofilms KW - Bacteria KW - E. coli KW - XPS PY - 2019 AN - OPUS4-49189 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbially influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) which act upon the metal by the reactiveness of hydrogen sulfide, and by withdrawal of the available electrons in electrical contact with the metal. Methanogenic archaea can also cause MIC by directly withdrawing electrons from the iron surface for methanogenesis. However, the mechanistic details and kinetics of the overall process are poorly understood. Precipitation of siderite, a by-product of methanogenesis, (4Fe + 5HCO3 + 5H+  4FeCO3 + CH4 + 3H2O) can lead to an insulating layer on the metal surface and lower the corrosion rate. Still, the extent of FeCO3 precipitation may be significantly influenced by environmental conditions such as pH and advective processes. T2 - Dechema CY - Frankfurt a. M., Germany DA - 13.05.2019 KW - MIC KW - Corrosion KW - Methanogens KW - Corrosion product PY - 2019 AN - OPUS4-47982 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Herrmann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC T2 - Einladung zum Kolloquium HZDR – Helmholtz-Zentrum Dresden-Rossendorf CY - Dresden, Germany DA - 24.09.2019 KW - Corrosion KW - MIC KW - Archaea KW - Methanogens KW - Environmental Simulation PY - 2019 AN - OPUS4-49403 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Herrmann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC T2 - Archaea Meeting-Schmitten VAAM Fachgruppe CY - Schmitten, Germany DA - 12.09.2019 KW - Corrosion KW - MIC KW - Archaea KW - Methanogens KW - Environmental Simulation PY - 2019 AN - OPUS4-49405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -