TY - CONF A1 - Vogel, Christian A1 - Kratz, S. T1 - Charakterisierung der P-Verfügbarkeit in Düngemitteln durch P-Senken N2 - Recycling-Düngemittel auf Basis von sekundären Ressourcen (Gülle, Gärreste, Klärschlamm, Tiermehl etc.) gewinnen in den letzten Jahren zunehmend an Bedeutung in der Landwirtschaft. Die in den Recycling-Düngemitteln enthaltenen P-Spezies weichen oft stark von denen in konventionell hergestellten Düngemitteln aus Rohphosphat ab, zudem enthalten Recyclingdünger oft mehrere verschiedene P-Formen. Die Pflanzenverfügbarkeit des P in ist ganz wesentlich von der enthaltenen P-Form abhängig. Derzeit gibt es außer zeitaufwendigen und kostspieligen Gefäß- und Feldversuchen keine zufriedenstellende Testmethode zur Analyse der P-Pflanzenverfügbarkeit von unterschiedlichen Recycling P-Düngemitteln. Die im europäischen Düngemittelrecht normierten chemischen Extraktionsmethoden (Wasser, Zitronensäure, Ameisensäure, neutral Ammoniumcitrat etc.) zeigen oftmals keine oder nur sehr geringe Korrelation zu der P-Aufnahme von Pflanzen in Gefäßversuchen mit Recycling-Düngemitteln (Kratz et al. 2010, Steckenmesser et al. 2017, Vogel et al. 2017). Eine grundlegende Schwäche chemischer Extraktionsmethoden liegt darin, dass es sich dabei um statische Methoden handelt, die nicht in der Lage sind, die im System Boden/Düngemittel-Bodenlösung-Pflanze stattfindenden dynamischen Prozesse wie P-Freisetzung und Entzug durch die Pflanzenwurzeln abzubilden. Einen Lösungsansatz bieten hier sog. P-Senken-Methoden. Bereits in den 1950er Jahren wurden erstmals P-Senken zur Analyse des Boden-P angewendet (Chardon et al. 1996). In den darauffolgenden Jahrzehnten wurden verschiedene P-Senken auf der Basis von Eisenoxid-Papier entwickelt (Chardon et al. 1996). Jedoch konnten diese Ansätze auch nur begrenzt zur Bestimmung der P-Pflanzenverfügbarkeit des Boden-P eingesetzt werden. Mitte der 1990er Jahre wurde die DGT (engl. diffusive gradients in thin films) Methode entwickelt (Zhang et al. 1998). Bei der DGT Methode diffundiert P aus der Bodenlösung des angefeuchteten Bodens durch einen Membranfilter und die Diffusionsschicht und wird anschließend an einer Bindungsschicht absorbiert. Durch den Diffusionsgradienten wird das Gleichgewicht in der Bodenlösung permanent gestört, wodurch auch labiles P im Boden gelöst wird. Die stetige Entnahme von P aus der Bodenlösung über die Diffusions-/Bindungsschicht simuliert dabei den Entzug von P durch die Pflanzenwurzel. Die an die Bindungsschicht adsorbierte Menge an P korreliert stark mit der P-Aufnahme von Pflanzen (u.a. Mason et al. 2005, 2013; Menzies et al. 2005, Six et al. 2012). Im Gegensatz zu chemischen Extraktionsmethoden werden bei der DGT Methode Mischungen an Düngemittel und Boden für mehrere Tage inkubiert (Vogel et al. 2017; Duboc et al. 2017), da ansonsten wasserlösliche P-Dünger den DGT Adsorber sättigen und wasserunlösliche P-Dünger unterschätzt werden. Ein bis zwei Wochen Inkubation sind ausreichend, damit sich pflanzenverfügbares P in die Mischungen bildet. In letzter Zeit haben verschiedene Forschungsgruppen gezeigt, dass die DGT Methode auch eine sehr gute Korrelation mit der Pflanzenverfügbarkeit verschiedener Typen von (Recycling-)P-Düngemitteln aufweist (Vogel et al. 2017; Duboc et al. 2017; Foereid 2017; Haarstad and Bavor 2017; Lemming et al. 2017). Bei Gefäßversuchen mit verschiedenen Recycling P-Düngemitteln konnte die DGT Methode den Ertrag bzw. die P-Aufnahme von Mais deutlich besser vorhersagen als herkömmliche chemische Extraktionsmethoden (Vogel et al. 2017; Duboc et al. 2017). Daher kann die DGT Methode im Vorfeld der Zulassung von neuen Düngermitteltypen als zuverlässige und robuste Methode zum Screening von Produktvarianten eines Düngemittelherstellers verwendet werden. Um dieses Messverfahren im Rahmen des Düngemittelrechts als Bewertungsinstrument für die Abschätzung der Pflanzenverfügbarkeit unterschiedlicher Düngemittel zu verwenden, muss es allerdings zunächst standardisiert werden. Zu diesem Zweck bietet sich der Einsatz eines „standardisierten“ Bodens bzw. Bodenrezepts an. Zur Kalibrierung der Methode im jeweiligen Labor könnten auch chemisch definierte P-Verbindungen mit bekannter Löslichkeit/Pflanzenverfügbarkeit als Referenz-substanzen verwendet werden. T2 - Fachgespräch Recycling-Phosphate als Düngemittel für die Landwirtschaft CY - Bonn, Germany DA - 14.02.2018 KW - Düngemittel KW - Sekundärrohstoffe KW - Phosphor KW - DGT KW - P-Senken KW - Extraktionsversuche PY - 2018 AN - OPUS4-44339 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Chemische Charakterisierung von P-Recyclaten N2 - Zukünftig werden vermehrt P-Recyclate auf den Düngemittelmarkt kommen. Diese müssen ausreichend charakterisiert werden, um Sicherheit und Wirksamkeit beurteilen zu können. Mit dem Vortrag wurde der wissenschaftliche Beirat für Düngungsfragen des Bundesministeriums für Ernährung und Landwirtschaft beraten. T2 - Fachgespräch Recycling-Phosphate als Düngemittel für die Landwirtschaft CY - Bonn, Germany DA - 14.02.2018 KW - P-Recyclate KW - Sekundärrohstoffe PY - 2018 AN - OPUS4-44178 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Resultiert normgerechte Ausführung verlässlich in hoher Qualität? N2 - Normgerechte Ausführung resultiert in Qualität, aber sie ist nicht allein ein Garant auch für hohe Qualität. Hierfür sind begleitend immer auch nachgeordnete Richtlinien wie z. B. spezifische Gütekriterien zu erfüllen. Der Vortrag erklärt die Normungsarbeit auf nationaler und internationaler Ebene und schildert die Stärken aber auch die Schwächen bei der Erstellung von Normen. Dabei ist die Konsensbildung zwischen unterschiedlichen interessierten Kreisen mit deren Partikularinteressen oftmals ein Hindernis, das aber über Zusatzvereinbarungen und der Norm nachgeordneten Regeln überwunden werden kann. T2 - Tagung des Deutschen Holzschutzfachverbandes für Ausenholzprodukte CY - Berlin, Germany DA - 19.01.2018 KW - Normung KW - DIN KW - CEN KW - ISO KW - Gütezeichen PY - 2018 AN - OPUS4-43852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöller, Renate A1 - Hahn, Oliver A1 - Danielewski, A. A1 - Giel, R. A1 - Overgaauw, E. T1 - Untersuchungen der Humboldt Codices "Fragmens de peinture hiéroglyphique Aztèques, deposés à la bibliotheque royale de Berlin" N2 - In der Berliner Sammlung "Manuscripta Americana" befinden sich Fragmente von Bilderhandschriften, die Alexander von Humboldt 1804 in Mexiko erwarb und der Königlichen Bibliothek schenkte. Die in der frühen Kolonialzeit hergestellten verschiedenartigen Codices waren damals schon nicht mehr an den Orten ihrer ursprünglichen Verwendung. Entsprechend ihres Seltenheitswertes gelangten einzelne Schriftstücke seit der Conquista in die Bestände bedeutender Persönlichkeiten. Hierzu fertigte man auch Abschriften oder Kopien an, oder zerstückelte sogar einzelne Blätter, so dass die Darstellungen auf den abgetrennten Fragmenten oft nur zum Teil abgebildet vorliegen. Um herauszufinden, ob einige Schriftstücke der "Humboldt Codices" in Bezug zu einander stehen, werden die Dokumente, ihre Symbole und Schriftzeichen und das zur Herstellung verwendete Material miteinander verglichen. Mit den für die Analyse von Manuskripten bewährten Untersuchungsmethoden werden Papier und Farbmittel identifiziert. Hierzu zählen Raman-, FTIR-, Röntgenfluoreszenz- und VIS- Spektroskopie. Charakteristisch für die Herstellung von schriftlichen Dokumenten in der Kolonialzeit von Amerika ist die Verwendung von indigenem Material wie Papier aus Baumrinde und Pflanzenfarben zusammen mit den aus Europa bekannten Materialien. Geklärt wird, inwieweit neben den bekanntesten Farbstoffen wie Cochenille, Mayablau oder Mischungen mit Tonmineralen auch mineralische Pigmente zum Einsatz kamen. Vorgestellt werden die auf Tafel 36 in den "Vues des Cordillères et Monuments des Peuples Indigènes de l`Amerique, Voyage de Humboldt et Bonpland" abgebildeten Fragmente. Die hier von Humboldt vorgenommene Zusammenstellung wird mit der Farbpalette der in Berlin archivierten originalen Schriftstücke verglichen. Die Interpretation der Ergebnisse gibt einen Hinweis auf die Zuordnung oder auch Zusammengehörigkeit dieser einzigartigen Dokumente amerikanischer Geschichte. Hierbei wird die Frage aufgeworfen, inwiefern davon auszugehen ist, dass diese mit weiteren Fragmenten in Verbindung gebracht werden können, was für die Beleuchtung der kulturhistorischen Zusammenhänge von großer Bedeutung ist. T2 - Archäometrie und Denkmalpflege 2018 CY - Hamburg, Germany DA - 20.03.2018 KW - FTIR KW - Humboldt Codices KW - XRF KW - VIS KW - RAMAN PY - 2018 AN - OPUS4-44746 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Tools for the characterization of secondary raw materials - status of leaching test application N2 - Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed. T2 - Travelling Conference CY - Perth, Australia DA - 06.02.2018 KW - Leaching KW - Risk assessment KW - Robustness studies PY - 2018 AN - OPUS4-44723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Tools for the characterization of secondary raw materials - status of leaching test application N2 - Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed. T2 - Travelling Conference CY - Ho-Chi-Ming City, Vietnam DA - 01.02.2018 KW - Leaching KW - Risk assessment KW - Robustness studies PY - 2018 AN - OPUS4-44724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Tools for the characterization of secondary raw materials - status of leaching test application N2 - Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed. T2 - Travelling Conference CY - Seoul, Korea DA - 29.01.2018 KW - Leaching KW - Risk assessment KW - Robustness studies PY - 2018 AN - OPUS4-44725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, René A1 - Szuppa, Tony T1 - Untersuchungen von Bodenmaterialien auf mobilisierbare organische Stoffanteile im Elutionsmethodenvergleich N2 - Im Beitrag wurden erste Ergebnisse eines laufenden UFOPLAN-Vorhabens zu den neuen Kriterien der Verwertungsmöglichkeiten von Bodenmaterialien außerhalb der durchwurzelbaren Bodenschicht nach den §§ 6 bis 8 der Novelle der BBodSchV vorgestellt. Der Schwerpunkt lag auf Untersuchungen der Schadstoffgruppe der PAK. Dabei wurden Probleme der Vergleichbarkeit und Leistungsfähigkeit verschiedener Elutions- und Analyseverfahren der PAK-Analytik diskutiert. T2 - Fachgespräch Feststoffuntersuchungen CY - Essen, Germany DA - 06.03.2018 KW - Leaching KW - PAK KW - Böden PY - 2018 AN - OPUS4-44726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Piechotta, Christian T1 - Vergleich von Elutionsuntersuchungen auf perfluorierte Chemikalien (PFC) N2 - Im Beitrag wurden Ergebnisse von Elutionsuntersuchungen mit PFC kontaminierten Bodenmaterialien vorgestellt. Zum einen waren das Untersuchungen zur Eignung von Säulenversuchen für diese Schadstoffgruppe und zum anderen vergleichende Schüttel- und Säulenversuche für zwei verschiedene Böden mit unterschiedlichen PFC-Kontaminationsquellen. T2 - Fachgespräch Feststoffuntersuchungen CY - Essen, Germany DA - 05.03.2018 KW - Leaching KW - PFC KW - Böden PY - 2018 AN - OPUS4-44727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute A1 - Bandow, Nicole T1 - Auswaschversuche zur Charakterisierung der Umweltverträglichkeit von Bauprodukten N2 - Im Vortrag werden Auswaschversuche mit Bauprodukten vorgestellt, die dazu dienen sollen, Bauprodukte mit geringer Auswaschung zu erkennen. Zu verschiedenen Bauprodukten (Lacke für Außenanwendungen, Wärmedämmverbundsystemen, Dachziegel und Dachfolien) werden ausgewählte Ergebnisse vorgestellt. Die Eignung der Auswaschverfahren und die Testergebnisse werden bewertet. T2 - Umwelteigenschaften von Bauprodukten: Schnellbewitterung, Leaching, Modellierung CY - Holzkirchen, Germany DA - 17.04.2018 KW - Testverfahren KW - Auswaschversuche KW - Bauprodukte PY - 2018 AN - OPUS4-44734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Phenotypic diversity in microbial metabolism and antimicrobial resistance N2 - Most microorganisms live in environments where nutrients are limited and fluctuate over time. Cells respond to nutrient fluctuations by sensing and adapting their physiological state. Recent studies suggest phenotypic heterogeneity in isogenic populations as an alternative strategy in fluctuating environments, where a subpopulation of cells express a function that allows growth under conditions that might arise in the future. It is unknown how environmental factors such as nutrient limitation shape phenotypic heterogeneity in metabolism and whether this allows cells to respond to nutrient fluctuations. Here, we show that substrate limitation increases phenotypic heterogeneity in metabolism, and this heterogeneity allows cells to cope with substrate fluctuations. We subjected the N2-fixing bacterium Klebsiella oxytoca to different levels of substrate limitation and substrate shifts, and obtained time-resolved single-cell measurements of metabolic activities using nanometre-scale secondary ion mass spectrometry (NanoSIMS). We found that the level of NH4+ limitation shapes phenotypic heterogeneity in N2 fixation. In turn, the N2 fixation rate of single cells during NH4+ limitation correlates positively with their growth rate after a shift to NH4+ depletion, experimentally demonstrating the benefit of heterogeneity. The results indicate that phenotypic heterogeneity is a general solution to two important ecological challenges - nutrient limitation and fluctuations - that many microorganisms face. Currently, we use NanoSIMS to develop a new approach that defines functionally-relevant, phenotypic biodiversity in microbial systems. In the last part of my presentation, I will highlight why the concept of phenotypic diversity is relevant for the understanding of antimicrobial resistance. T2 - Berlin Seminar for Resistance Research at FU Berlin Veterinary Medicine CY - Berlin, Germany DA - 01.03.2018 KW - Antimicrobial Resistance KW - Metabolism KW - Phenotypic diversity PY - 2018 AN - OPUS4-44597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kjaervik, Marit A1 - Schwibbert, Karin A1 - Dietrich, P. A1 - Thissen, A. A1 - Unger, Wolfgang T1 - Surface characterisation of bacteria and biofilms by NAP-XPS N2 - The XPS information depth of approximately 10 nm is in the same size range as the outer membrane of the gram-negative bacteria, which makes XPS a suitable tool for determining the elemental composition of the bacterial surface and monitor changes caused by outer stress like dehydration or exposure to antimicrobials. However, bacteria are inherently in a hydrated state, and therefore only compatible to ultra-high vacuum after extensive sample preparation, which may degrade the sample constituents. This issue is addressed by the development of near-ambient pressure (NAP)-XPS, which enables bacteria and biofilms to be characterised in their native wet state. Artificial biofilms, bacteria and biofilms of Escherichia coli have been characterised with the laboratory NAP-XPS instrument EnviroESCA from SPECS GmbH, at pressures ranging from high vacuum to 12 mbar, and in both humid and dry environment. By studying biological samples in their native wet state, new insight about composition and transport of drugs through cell membranes and the extracellular polymeric substance (EPS) of biofilms can be obtained. In this contribution, the latest progress on biofilm characterisation by NAP-XPS will be presented, and measurement capabilities and limitations will be discussed. T2 - Die Frühjahrstagung der Deutsche Physikalische Gesellschaft CY - Berlin, Germany DA - 12.03.2018 KW - Biofilms KW - E. coli KW - Alginate KW - NAP-XPS PY - 2018 AN - OPUS4-44500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sieksmeyer, Thorben A1 - McMahon, Dino Peter A1 - He, Shulin T1 - Beyond nutrition: host-microbiota interactions drive shifts in the behavioural phenotypes of cockroaches N2 - Recent studies have shown that host-microbiota interactions can lead to dramatic changes in host phenotype especially behaviour. We investigate the causal drivers of microbe-associated shifts in host phenotype by examining how feeding behaviour is modulated by a bacterial infection in an omnivorous cockroach: Blatta orientalis. We conducted food-choice experiments after challenging hosts with the common entomopathogenic soil bacterium Pseudomonas entomophila to understand the impact of bacterial pathogens on host macronutrient preference. We find that immune challenge by this bacterium drives a sharp decline in carbohydrate intake and results in a relative increase in the ratio of protein to carbohydrate consumed. Additionally, infected cockroaches reduce their overall nutrient intake. We show for the first time that cockroach feeding behaviour is dynamically modulated by a pathogen. In contrast to studies on Spodoptera moths, this modulation does not impact any of the immune parameters we measured: it does not affect the abundance of immune related proteins in the hemolymph, hemolymph antimicrobial activity, or survival. This leads to the possibility that as long-lived omnivorous species B. orientalis may be better adapted to unpredictable variation in food availability and quality. An illness-induced anorexia-like response which is thought to assist hosts in limiting nutritional resources available to pathogens is therefore the most likely cause of the observed phenotype. Reduction of carbohydrate intake by sick individuals would be consistent with such an explanation. In another cockroach species Blatella germanica we also investigate whether in addition to pathogens, host microbiota especially gut commensals are causally responsible for shifts in host behavioural phenotype and immune competence. To address this, we conduct food-choice and immunechallenge experiments in germ-free cockroaches and naïve cockroaches. T2 - XI EUROPEAN CONGRESS OF ENTOMOLOGY CY - Neapel, Italy DA - 02.07.2018 KW - Bacterial infection KW - Feeding behaviour KW - Gut microbiota KW - Illness-induced anorexia KW - Proteomics PY - 2018 AN - OPUS4-45414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kjaervik, Marit A1 - Dietrich, P. A1 - Thissen, A. A1 - Schwibbert, Karin A1 - Unger, Wolfgang T1 - Quantitative biocide profile measurements by calibrated NAP-XPS N2 - Progress update for the EMPIR-project MetVBadBugs- Quantitative measurement and imaging of drug-uptake by bacteria with antimicrobial resistance. T2 - MetVBadBugs 26 M project meeting CY - South Mimms, UK DA - 05.07.2018 KW - Biofilms KW - Alginate KW - Antibiotics KW - E. coli KW - XPS PY - 2018 AN - OPUS4-45402 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Bosch, S. A1 - Rabin, Ira A1 - Hahn, Oliver T1 - Scientific service project Z02 at the CSMC: Material-science methods of reconstructing the history of manuscripts N2 - Z02 is one of the three technically supporting projects at the CSMC. In collaboration with Z01 and Z03, it aims at bridging the gap between humanities and natural sciences and technology. To that purpose, we set up a laboratory with a range of high-end instruments, most of them mobile, allowing thorough non-destructive analysis of manuscripts. In addition to working on constantly improving the laboratory and the methods of analysis, a substantial part of our activities is dedicated to service, by supporting different research projects conducted at the center. In this talk, we will present our equipment and the possibilities offered by the different techniques available regarding the different kinds of missions: typology and classification of inks, provenance studies, recovery of faded inscriptions and palimpsests, reconstruction of the history of manuscripts, authentication and dating. We will give a brief overview of our past and ongoing activities in the frame of the second phase of the CSMC. Finally, a selection of three projects will be presented in greater detail to highlight the possibilities of our laboratory and the diversity of missions which can be carried out: - Support of project C08 on East Frankish manuscripts containing collections of formulae - Identifying color materials applied in Muhammad Juki's Shahnamah with non-invasive combined methods - Checking for the presence of metals in the Herculaneum papyri T2 - 3rd International Conference on Natural Sciences and Technology in Manuscript Analysis CY - Hamburg, Germany DA - 13.06.2018 KW - CSMC KW - Manuscript KW - Ink KW - Pigment PY - 2018 AN - OPUS4-45504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kjaervik, Marit A1 - Dietrich, P. A1 - Thissen, A. A1 - Schwibbert, Karin T1 - Surface characterisation of biological samples by near-ambient pressure XPS N2 - A presentation held for the seminar "Ausgewählte analytische Methoden der Physik" hosted by Prof. Birgit Kanngießer at TU Berlin. The first part focus on depth-dependent XPS-measurements (XPS, synchrotron HAXPES) to obtain a concentration profile of iodine in an artificial biofilm. In the second part, NAP-XPS measurements of various bacterial samples are presented. T2 - Forschungsseminar "Ausgewählte analytische Methoden der Physik", TU Berlin CY - Berlin, Germany DA - 17.07.2018 KW - Biofilms KW - Alginate KW - Agarose KW - HAXPES KW - NAP-XPS PY - 2018 AN - OPUS4-45505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionsarme Materialien und Produkte für eine saubere Innenraumluft N2 - Mit dem Fokus auf eine saubere Innenraumluft wird darauf eingegangen, welche Emissionen aus Materialien und Produkten es gibt und wie sie nach Art und Flüchtigkeit definiert sind und wie sie gemessen werden. Im weiteren wird dargestellt, was und wie viel aus Materialien und Produkten emittieren kann und wie die Emissionen zu bewerten sind. Hierbei wird auch auf besonders emissionsarme Materialien und Produkte eingegangen. T2 - Kolloquium am Institut für Technischen Umweltschutz, Sommersemester 2018 CY - Berlin, Germany DA - 28.05.2018 KW - Emissionen KW - Luft KW - VOC KW - Aerosol KW - Radon KW - Geruch PY - 2018 AN - OPUS4-45052 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Perth, Australia DA - 06.02.2018 KW - Ecotoxicity KW - HP14 KW - Recycling materials PY - 2018 AN - OPUS4-44456 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussionen zur vorläufigen Zulassungsrichtlinie von Bewehrungsgittern für Deponieoberflächenabdichtungen und zu Auftragsnähten in Kunststoffdichtungsbahnen N2 - Die BAM wurde 2009 u. a. mit der Zulassung von Bewehrungsgittern für den Deponiebau beauftragt. Der Stand von Wissenschaft und Technik bot jedoch keine ausreichende Grundlage, die tatsächlich relevanten Widerstände und die mit diesen Widerständen verbundene Wechselwirkung zwischen Gitter und Boden im Hinblick auf eine mindestens 100-jährige Funktionsdauer realistisch beurteilen zu können. Es wurde daher nur eine vorläufige Zulassungsrichtlinie für diese Produkte erarbeitet. In der Zwischenzeit hat sich ein neuer Kenntnisstand ergeben. Vor diesem Hintergrund hat die AG (Arbeitsgruppe) Geogitter des Fachbeirats der BAM am 26.09.2017 getagt. Es sollen die aktuellen Erkenntnisse und Schlussfolgerungen für die Zulassung in Kürze vorgestellt werden. Die entsprechenden Kapitel beruhen dabei auf einem Arbeitspapier von W.W. Müller und dem Autoren, das der Arbeitsgruppe zur Diskussion vorgelegt wurde. Weiterhin soll über Entwicklungen in Zusammenhang mit Kunststoffdichtungsbahnen (KDB) berichtet werden. Die Anforderungen an die Schweißzusätze für das Extrusionsschweißen wurden angepasst. Zudem soll über die aktuelle Diskussion der Schweißbarkeit unterschiedlicher HDPE Materialien informiert werden. Die maßgebliche DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 wird derzeit offenbar so ausgelegt, dass Materialien mit völlig unterschiedlichen Schmelze-Massefließrate miteinander verbunden werden können. Dies steht allerdings im grundlegenden Widerspruch zum Stand der Technik. T2 - 14. Leipziger Deponiefachtagung - Planung, Bau, Betrieb, Stilllegung, Nachsorge und Nachnutzung von Deponien CY - Leipzig, Germany DA - 06.03.2018 KW - Bewehrungen aus Kunststoff KW - Kunststoffschweißen KW - Deponietechnik PY - 2018 AN - OPUS4-44418 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Seoul, Korea DA - 29.01.2018 KW - Ecotoxicity KW - Recycling materials KW - HP14 PY - 2018 AN - OPUS4-44454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Ho-Chi-Ming City, Vietnam DA - 01.02.2018 KW - Ecotoxicity KW - HP14 KW - Recycling materials PY - 2018 AN - OPUS4-44455 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adamczyk, Burkart A1 - Schraut, Katharina A1 - Adam, Christian T1 - Nachbehandlung von Stahlwerksschlacke und deren Verwertung als Klinkermaterial N2 - LD-Schlacken weisen eine große chemische Ähnlichkeit zu Protlandzementklinker auf. Sie enthalten jedoch noch bis zu 30% Eisen, das mineralisch in oxidischer Form gebunden vorliegt. Dadurch kann sich bei der Erstarrung die wichtigste Klinkerphase "Alit" nicht ausbilden. Durch eine reduzierende Schmelzbehandlung der Schlacke kann des mineralisch gebundene Eisen als Metall separiert werden. Dadurch wird auch die Mineralogie der Schlacke so verändert, dass auch sie nun praktisch einem Portlandzementklinker entspricht. Entsprechende Versuche wurden am kleintechnischen Lichtbogenofen der BAM durchgeführt. Es werden Ergebnisse vorgestellt und auf Grenzen und Möglichkeiten eines derartigen Prozesses im Hinblick auf eine industrielle Umsetzung eingegangen. T2 - Berliner Konferenz "Mineralische Nebenprodukte und Abfälle" CY - Berlin, Germany DA - 11.06.2018 KW - LD-Schlacke KW - Lichtbogenofen KW - Zementklinker PY - 2018 AN - OPUS4-45221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Eine kleine Natur- und Kulturgeschichte der Kleidermotte – nebst Möglichkeiten ihrer biologischen Bekämpfung N2 - Zu den unerwünschten Gästen im Museum oder im Haushalt gehört zweifelsohne die Kleidermotte Tineola bisselliella. Es sind die Larven dieses Kleinschmetterlings, die die Schäden verursachen. Neben der konventionellen Schadensabwehr besteht die Möglichkeit, Schlupfwespen zur Bekämpfung der Larven einzusetzen. Der Vortrag rekonstruiert die Natur- und Kulturgeschichte der Kleidermotte anhand ökologischer Studien und historischen Indizien. T2 - Konservierungswissenschaft im Dialog Rathgen Forschungslabor CY - Berlin, Germany DA - 30.01.2018 KW - IPM KW - Museum KW - Biologische Bekämpfung KW - Kulturgut PY - 2018 AN - OPUS4-43988 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kjaervik, Marit A1 - Schwibbert, Karin A1 - Unger, Wolfgang A1 - Thissen, A. A1 - Dietrich, P. T1 - Progress on characterisation of biofilms by NAP-XPS N2 - Progress talk on characterisation of biofilms by NAP-XPS in the framework of the MetVBadBugs EURAMET-project T2 - MetVBadBugs 24 M project meeting CY - Turin, Italy DA - 06.02.2018 KW - Biofilms KW - E. coli KW - Alginate KW - NAP-XPS PY - 2018 AN - OPUS4-44065 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Schoknecht, Ute T1 - Auswaschung aus Wärmedämmverbundsystemen N2 - Ausgewählte Ergebnisse des UBA-Vorhabens "Beregnete Bauteile und Bauprodukte: Entwicklungen für Vergabegrundlagen für den Blauen Engel mit Hilfe von Auslaugtest" werden für organische und anorganische Analyten präsentiert. Ein Schwerpunkt ist den Einfluss der verschiedenen Schichten von WDVS-Systemen aufzuzeigen. T2 - UBA Fachgespräch "Umwelteigenschaften von Bauprodukten: 'Schnellbewitterung, Leaching, Modellierung CY - Valley, Germany DA - 17.04.2018 KW - Auswaschung KW - DSLT KW - Tauchtest KW - Wärmedämmverbundsystem PY - 2018 AN - OPUS4-44720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Mölders, N. A1 - Sauerwald, T. A1 - Schultealbert, C. A1 - Mull, B. T1 - Two new promising approaches for quality assurance measures for materials emissions testing N2 - Two new approaches towards an emission reference material for use in quality assurance measures for materials emissions testing were developed and intensively tested. The overall goal was to obtain solid materials with homogenous and reproducible (S)VOC release. Since the application in inter-laboratory comparisons is aimed at, it should furthermore be long-term stable to ensure safe shipment to the customer without sustaining compound losses. In the first approach, thermoplastic polyurethane (TPU) was impregnated with the VOC texanol under high-pressure with liquid CO2 as solvent. In the second, styrene (VOC) and the SVOC 2,6-diisopropylnaphthalene (DIPN) were spiked into vacuum grease (VG) and a mixture of paraf-fin/squalane (P/S). For the prediction of the emission rates a finite element model (FEM) was developed for the VG and P/S type materials. All requirements for reference materials were fulfilled, whereas the TPU samples need to be aged for about 10 days until repeatable and reproducible emission rates were obtained. T2 - Indoor Air 2018 CY - Philadelphia, PA, USA DA - 22.07.2018 KW - Emission reference material KW - Volatile organic compounds KW - CO2 assisted impregnation KW - FEM model PY - 2018 AN - OPUS4-45611 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Schulenburg, F. A1 - Reuter, M. A1 - Stelter, M. T1 - Optimierung eines pyrometallurgischen Tantal- und Niob- Recyclingprozesses mithilfe von On-Line LIBS N2 - Die Entwicklung von Hochleistungselektronik zu immer kleineren Bauformen ohne Leistungseinbußen ist ohne den Einsatz von Technologiemetallen wie Niob und Tantal heute praktisch nicht mehr realisierbar. Besonders in technischen Geräten wie Smartphones und Tablets sind Tantal- und Niobkondensatoren aufgrund ihrer hohen Leistungsdichten bereits unverzichtbar geworden. Für die nachhaltige Produktion von Elektronik stellt jedoch vor allem das Tantalerz Coltan als sogenanntes „conflict mineral” ein großes Problem dar. Um den Wirtschaftsstandort Europa unabhängiger von Primärrohstoffimporten aus Krisenregionen zu machen, ist die Entwicklung von effizienten Recyclingverfahren heute wichtiger denn je. An der Bundesanstalt für Materialforschung und -prüfung (BAM) findet daher zurzeit die Optimierung eines pyrometallurgischen Industrieprozesses zur Niob- und Tantalrückgewinnung statt, welchem hauptsächlich niedrigkonzentrierte metallurgische Rückstände aus der Tantal- und Niob- bzw. der Zinngewinnung als Einsatzstoffe dienen. Zu diesem Zweck werden im kleintechnischen Lichtbogenofen der BAM (480 kVA, max. Materialdurchsatz ca. 150 kg/h) Versuche mit einem neuen innovativen Messgerät durchgeführt, welches eine On-Line Analyse von Hochtemperaturprozessen ermöglicht. Der eingesetzte Prototyp nutzt das Verfahren der laserinduzierten Plasmaspektroskopie (LIBS), um die chemische Zusammensetzung der Schlackephase noch im Schmelzbad und während eines Schlackeabgusses zu bestimmen. Nach einer Kalibrierung auf das vorliegende Stoffsystem ermöglicht dieser On-Line-LIBS Prototyp der BAM daher eine in-situ Bestimmung der Elementverteilung in der Schmelze. Die hier gewonnenen Daten sollen helfen, die aktuelle Prozessführung zu verbessern und die Tantal- und Niobausbeute noch weiter zu erhöhen. T2 - Jahrestreffen Bremen 2018 der ProcessNet-Fachgruppen Hochtemperaturtechnik (HTT), Abfallbehandlung und Wertstoffrückgewinnung (AuW) CY - Bremen, Germany DA - 06.03.2018 KW - Laser-induced breakdown spectroscopy KW - Tantal KW - On-Line Analyse KW - Recycling KW - Pyrometallurgie PY - 2018 AN - OPUS4-45612 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Schulenburg, F. A1 - Bartmann, U. A1 - Beckmann, T. A1 - Michalik, K. A1 - Reuter, M. A1 - Stelter, M. T1 - Optimisation of a Pyrometallurgical Niobium and Tantalum Recyling Process with on-line-LIBS N2 - Tantalum and niobium are essential for the development of electronics towards a more and more compact design, but without reducing their performance today. Especially in smart phones and tablets, tantalum and niobium capacitors with high charge densities have already become almost indispensable. However, tantalum as a critical raw material is still a problem for the sustainable production of electronics. Due to this fact, the existence of efficient recycling processes especially in Europe is becoming even more important nowadays. The Bundesanstalt für Materialforschung und -prüfung (BAM) is currently working on the optimisation of an existing pyrometallurgical tantalum recycling process. Optimisation of this industrial process is carried out in a small-scale electric arc furnace (480 kVA, capacity approx. 150 kg/h) at BAM using a new and innovative equipment for on-line analysis of high temperature processes. The aim of this project is to identify the best timing for an optimum slag tapping, when the slag is lower than minimum targeted tantalum concentration. Hence, LIBS (Laser induced breakdown spectroscopy) is used to identify the chemical composition of the slag layer and during slag tapping. The on-line-LIBS prototype of BAM enables an in-situ measurement of the element distribution in the melt after calibration on the slag system. First results of this joint research project will be presented including on-line-LIBS-measurements and thermodynamic and kinetic aspects of the process. T2 - European Mineral Processing & Recycling Congress (EMPRC 2018) CY - Essen, Germany DA - 25.06.2018 KW - Laser-induced breakdown spectroscopy KW - Process control KW - Tantalum KW - In-situ analysis KW - Pyrometallurgy PY - 2018 AN - OPUS4-45614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - OECD Prüfrichtlinie für die Größenbestimmung von Nanomaterialien N2 - Erste Ergebnisse des Projektes "OECD Prüfrichtlinie für die Größenbestimmung von Nanomaterialien" mit Vorstellung der beteiligten Fachbereiche. T2 - Expertenaustausch BAM-BMU-BMWi CY - Berlin, Germany DA - 01.06.2018 KW - Nano KW - OECD KW - Nanopartikel KW - Nanomaterial KW - Größenbestimmung PY - 2018 AN - OPUS4-45110 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Schmidt, Alexandra T1 - OECD-Prüfrichtlinie zur Größenbestimmung von hergestellten Nanomaterialien N2 - Impulsvortrag für den Beirat des Themenfeldes Umwelt über die in Erstellung befindliche OECD Prüfrichtlinie für die Größenbestimmung von künstlich hergestellten Nanomaterialien. T2 - Sitzung des Beirates des Themenfelds Umwelt 2018 CY - Berlin, Germany DA - 26.02.2018 KW - Nano KW - OECD KW - Prüfrichtlinie KW - Nanopartikel KW - Nanomaterial PY - 2018 AN - OPUS4-45111 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Agency perspectives on geomembrane durability, service life and end of life N2 - Die Präsentation erläutert die Hintergründe der nationalen Anforderungen für die Verwendung von Kunststoffdichtungbahnen in Deponieabdichtungen. Die Beständigkeit wird diskutiert. Anforderungen an das Qualitatsmanagement während der Produktion der Produkte und der Bauphase werden aufgezeigt und die Auswirkungen auf die langzeitige Funktionserfüllung werden beschrieben. T2 - IGS TC-B GeoBarrier Workshop CY - Munich, Germany DA - 06.06.2018 KW - Beständigkeit KW - Kunststoffdichtungsbahnen KW - Deponiebau PY - 2018 AN - OPUS4-45123 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Schmidt, Alexandra A1 - Bachmann, V. A1 - Kämpf, K. A1 - Kuhlbusch, T. A1 - Schwirn, K. A1 - Völker, D. T1 - OECD Test Guideline on particle size and size distribution of manufactured nanomaterials N2 - The properties of nanomaterials are influenced not only by their chemical composition but also by physical properties (such as size, geometry and crystal structure). For the reliable determination and assessment of behaviour and effects of nanomaterials as well as for the determination of the exposure of humans and environment a comprehensive physical-chemical characterization of nanomaterials is essential. This is an important prerequisite to identify them as nanomaterials and to interpret and compare test results and - in future – to forecast interaction and effects of nanomaterials. In 2006, the OECD launched a sponsorship program for the testing of nanomaterials in which 11 nanomaterials were thoroughly investigated using a variety of methods. The aim of the project was, among other things, to find out where problems occur and where there are gaps in the measurement and test procedures and where are changes required. An important outcome of the sponsorship program was the finding that the OECD Test Guidelines should in several cases be extended to the specific needs in testing of nanomaterials. The existing standardized test methods of the OECD for physical-chemical characterization have not been developed for nanomaterials in particular. A high demand for an extension of the test guidelines was identified. Germany complied with the OECD's request in 2017 and has agreed to extend the “Test Guideline on Particle Size Distribution / Fiber Length and Diameter Distributions Test Guideline” for Manufactured Nanomaterials (MN). UBA commissioned BAM and BAuA with the preparation of the Test Guideline. The aim of the project is the development of a harmonized test protocol for a valid and reproducible determination of particle size and size distribution which is one of the most relevant physical-chemical properties for MNs. Different measuring methods provide different results for the size distribution of the particles. This is caused by the different measuring principles of the methods. Each method measures a specific parameter that ultimately determines particle size. First, the measured quantity differs for each method (Scattered light intensity, 2D image / projection, electric mobility, etc.). Second, the calculated diameters of the MN may differ (Feret Diameter, Area Projection, Mobility Diameter, Aerodynamic Diameter, Hydrodynamic Diameter). Third, a measuring method provides a size distribution which is measured either mass-based, surface-based or number-based. A conversion between the results requires additional parameters and thus possibly increases the measurement error. In addition to the technical differences, the individual parameters are strongly influenced by the structure and material of the nanoparticles. For example, a surface functionalization can lead to very different results in the size distribution. The suitability of measurement methods differs with the material of the MN. As a result, two very different results can be measured for the particle size distribution using two different methods, which are nevertheless both correct. Several large projects in recent years therefore concluded that nanomaterials should be characterized by at least two complementary method. Imaging techniques are regarded as one of these methods for the characterization, the complementary methods are supposed to be statistical methods. The different results for the size distribution of nanomaterials become problematic for the registration of new MN. A comparable and reproducible size distribution is a prerequisite for a standardized registration. In the future, the particle size distribution in the EU will also decide on the classification of a substance as a nanomaterial or as a non-nanomaterial. Especially in borderline cases, a standardized and comparable measurement methodology is therefore essential. T2 - BAM-PTB Workshop 2018 CY - Berlin, Germany DA - 14.05.2018 KW - Nano KW - OECD KW - Test Guideline KW - Size distribution KW - Particle PY - 2018 AN - OPUS4-45106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian T1 - Advantages of recycling gypsum plasterboards N2 - During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites. Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted. This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process. T2 - IV International Conference Progress of Recycling in the Built Environment CY - Lisbon, Portugal DA - 11.10.2018 KW - Environmental evaluation KW - CDW processing KW - Gypsum PY - 2018 AN - OPUS4-48079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehring, Grzegorz A1 - Targowski, P. A1 - Rabin, Ira T1 - Can an inkwell leak into ink? N2 - X-ray fluorescence analysis, due to its non-destructive nature and ist suitability to work with historic objects in situ, quickly became one of the most important methods for the evaluation of iron-gall ink. The main advantage of this qualitative and semi-quantitative method is that it makes it easy to differentiate between inks, based on the assumption that the differences result from the manufacture of the ink. This work explores the question whether the ink ‘fingerprint’ results strictly from the elemental composition of the basic ink ingredients even if it is stored in vessels made of metals or metal alloys. In addition, we tested and compared the performance of three different XRF spectrometers. We prepared various lab-grade inks according to historical ink recipes and measured the metal content of the ink deposited on sized cotton Linters paper with three types of XRF spectrometers: a simple hand-held device with an interaction spot of 4 mm and two devices equipped with poly-capillary Xray optics for line scanning and imaging. Since the exact elemental mass composition of the non-aged ink samples was known, we were able to evaluate the accuracy of the research procedure. Lab-grade inks were then aged in the metal jars imitating inkwells. The aging of the inks in the metal containers resulted in the significant change of the primary inks fingerprint as opposed to that of the control inks stored in glass containers. This effect was independently confirmed by the measurements conducted with every instrument we used. We will present a brief comparison of the results 43 achieved when using different spectrometers and a possible hypothesis explaining the processes that occurred. T2 - Konferenz -7th Meeting X-ray and other techniques in investigations of the objects of cultural heritage CY - Krakow, Poland DA - 17.05.2018 KW - Iron-gall ink KW - XRF KW - Inkwells KW - Ink composition KW - Performance comparison PY - 2018 AN - OPUS4-49157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seneschal-Merz, Karine A1 - Bücker, Michael A1 - Sander, C. T1 - Development of low melting glasses as durable transparent enamel colors for the manufacture of decorated glass panels N2 - Today glass is broadly used in modern architecture. For applications indoor it is possible to produce decor glass by using enamel colors and glass painting techniques without any problems. However, this is more limited for applications outdoor. Humidity and environmental pollution attack the surface of the coating and damage it strongly. There are only few colors on the market which are resistant towards acids and bases until now. Additionally, most of those colors are opaque. In order to extend the color palette, chemically resistant colored glasses are being developed which are transparent, relatively low melting and intensively toned even in thin coat thickness. To achieve such ambitious aim, many parameters have to match which act in complex manner. Metal oxides were used to color the glasses. A lead-free glass composition was developed to avoid an exposition of heavy metals to the environment. The glasses were characterized, in particular in terms of their thermal properties, their crystallization and corrosion behavior as well as their chemical and environmental durability. Different practical applications will be shown. T2 - 15th International Conference on the Physics of Non-Crystalline Solids & 14th European Society of Glass Conference CY - Saint-Malon, France DA - 08.07.2018 KW - Glass KW - Chemical durability KW - Corrosion KW - Enamel colors KW - Low melting KW - Environmental friendly KW - Architecture KW - Thermal properties PY - 2018 AN - OPUS4-45755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bartelmeß, Jürgen A1 - Gawlitza, Kornelia A1 - Kraus, Werner A1 - Chlvi-Iborra, Katherine A1 - Tiebe, Carlo A1 - Noske, Reinhard A1 - Bartholmai, Matthias A1 - Rurack, Knut T1 - Developments Towards a BODIPY-based fluorometric sensing device for multiple hazardous gases N2 - Fluorometric sensing is a versatile approach for trace analysis outside of the laboratory, requiring suitable sensor materials and their integration into sensing devices. The versatility of fluorophores as probes, especially in terms of the possibility to tailor their optical as well as their recognition properties by synthetic modifications in a wide range, renders them as superior active component for the preparation of optical sensing devices. Recent works at BAM in this field include, for example, the detection of nerve gas agents, illustrating impressively the aforementioned benefits of fluorophores in optical sensing applications. In the interdisciplinary project presented here, we target hazardous gases such as ammonia, benzene, and hydrogen sulfide, next to others, which pose a major threat to human health and environmental safety and for which the availability of a sensitive and reliable detection method is highly desirable. The dyes presented follow a “turn-on” fluorescence schematic, which allows for the selective and sensitive detection of the respective gaseous analyte. The immobilization of the probe in polymeric matrices is then the next step toward the fabrication of a prototype device for molecular sensing. Further steps in the project include the assembly of instruments for test-atmosphere generation, the referencing of the sensor system, development and implementation of an optical setup, and the testing of the prototype device under laboratory conditions and in the field. In this presentation, we give an overview over the recent developments on this topic in our groups. Highlights are hydrogen sulfide sensitive, BODIPY based transition metal complexes, which allow for a sensitive as well as selective detection of the toxic gas. In addition, we present a novel class of highly substituted BODIPY derivatives – pocket-BODIPYs – which are of a synthetically high versatility and can readily be modified to create pockets in the periphery of the molecule of defined geometries. This is illustrated on the successful encapsulation of benzene by a pocket-BODIPY derivative, confirmed by X-ray crystallographic analysis as well as by further spectroscopic and analytical methods. T2 - International Conference on Porphyrins and Phthalocyanins (ICPP-10) CY - Munich, Germany DA - 01.07.2018 KW - BODIPY dye KW - Fluorometric sensing KW - Gas sensing PY - 2018 AN - OPUS4-45646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stahl, E. A1 - Meiller, M. A1 - Dombinov, V. A1 - Herzel, Hannes T1 - ASHES-nutrient recycling from the thermo-chemical processing of waste bagasse and straw - Clips from a German-Brazilian collaborative research project N2 - The challenge of the project ASHES is focused on the recycling of nutrients from residues of thermochemical processing of by-products of sugar cane industry (bagasse/straw) in Brazil to increase the energy efficiency of thermal conversion and to enable the recycling of process ashes as fertilisers. Dry lignocellulosic biomass (straw, bagasse) are combusted, gasified and subsequently combined with post-thermochemical treatment in the AshDec process to increase the plant availability of phosphorus. Different fertilizer formulations are granulated/pelletized and tested regarding their storage/handling characteristics. T2 - Biomass Ash 2018 CY - Kopenhagen, Denmark DA - 06.06.2018 KW - Bagasse KW - Nutrient KW - Recycling PY - 2018 AN - OPUS4-45652 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Approval of geosynthetics, polymers and leak detection systems for German landfills N2 - Geokunststoffe spielen sowohl im internationalen als auch im deutschen Deponiebau eine Schlüsselrolle. Seit dem Erscheinen der Deponieverordnung (DepV) im Jahre 2009 bedürfen Geokunststoffe, Polymere und Dichtungskontrollsysteme einer Zulassung durch die BAM, wenn diese in deutschen Deponieabdichtungssystemen eingesetzt werden sollen. Die DepV stellt dabei allgemeine Anforderungen an die Geokunststoffe und den Zulassungsprozess für die Produkte auf. Geokunststoffe müssen danach ihre Funktion unter allen zu erwartenden äußeren und inneren Einflüssen über einen Zeitraum von mindestens 100 Jahren erfüllen. Dichtungskontrollsysteme müssen ihre Funktion über mindestens 30 Jahre erfüllen. Die Anforderungen der DepV werden durch die Zulassungsrichtlinien der BAM in konkrete technische Anforderungen für die Produkte aber auch für das Qualitätsmanagement und den Einbau etc. überführt. Bei der Erarbeitung der Zulassungsrichtlinien wird die BAM durch einen Fachbeirat, der sich aus Experten aus allen relevanten Bereichen zusammensetzt, beraten. Der Vorsitz des Fachbeirats liegt beim UBA. Es soll eine kurze Übersicht über die Produkte und die wichtigsten Anforderungen gegeben werden. Zudem soll erläutert werden, durch welche Maßnahmen in der Produktion und auf der Deponiebaustelle eine gleichbleibende Qualität der Produkte gewährleistet wird. T2 - COLLOQUIUM DEPARTMENT 4 „MATERIALS AND THE ENVIRONMENT” CY - Berlin, Germany DA - 14.11.2018 KW - Deponien KW - Geokunststoffe KW - Polymere KW - Dichtungskontrollsysteme PY - 2018 AN - OPUS4-46659 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Die Zulassung von Geokunststoffen nach der deutschen Deponieverordnung N2 - Seit dem Erscheinen der Deponieverordnung (DepV) bedürfen Geokunststoffe, Polymere und Dichtungskontrollsysteme einer Zulassung durch die BAM, wenn diese in deutschen Deponieabdichtungssystemen eingesetzt werden sollen. Die DepV ermöglicht den Einsatz verschiedener Komponenten. Sie stellt dabei allgemeine Anforderungen an die Geokunststoffprodukte auf. Dadurch beschreibt sie den Stand der Technik für Geokunststoffe, die in deutschen Abdichtungen eingesetzt werden. Diese Anforderungen werden durch die Zulassungsrichtlinien der BAM in konkrete technische Spezifikationen überführt. In dem Beitrag wird eine Übersicht über die Produkte und die entsprechenden Anforderungen gegeben. Zudem soll erläutert werden, durch welche Qualitätsmanagementmaßnahmen eine gleichbleibende Qualität und Funktionserfüllung der Produkte gewährleistet wird. T2 - 14. DEPONIEWORKSHOP Liberec - Zittau 2018 CY - Liberec, Czech Republic DA - 15.11.2018 KW - Deponien KW - Geokunststoffe KW - Polymere KW - Dichtungskontrollsysteme PY - 2018 AN - OPUS4-46661 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, Rene A1 - Szuppa, Tony T1 - Anpassungsbedarf für Untersuchungsmethoden nach BBodSchV zur Optimierung der Bewertung von Boden und Bodenmaterialien N2 - Im Beitrag wurden auf der Basis der Ergebnisse des laufenden UFOPLAN-Forschungsvorhabens „Monitoring zur Verwertung von Bodenmaterial“ die nach BBodSchV anzuwendenden Untersuchungsverfahren bewertet und Probleme bei der Untersuchung von Bodenmaterial insbesondere im Zusammenhang mit der Analyse von PAK im Feststoff und im Eluat aufgezeigt. Dabei wurde der Einfluss der Probenaufbereitung und Probenvorbereitung vor der Analytik berücksichtigt. T2 - 39. Sitzung des Fachbeirates für Bodenuntersuchungen des BMU CY - Berlin, Germany DA - 18.10.2018 KW - Bodenmaterial KW - Verwertung KW - BBodSchV KW - PAK PY - 2018 AN - OPUS4-46584 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Kugler, Stefan Anton A1 - Schaaf, T. A1 - Adam, Christian T1 - Herstellung neuer Düngemittelausgangsstoffe durch thermochemische Behandlung von Klärschlammaschen N2 - Der Fachbereich 4.4 hat zusammen mit der Firma Outotec ein thermochemisches Verfahren im Drehrohrofen entwickelt, um die Phosphorphasen in Klärschlammasche umzuwandeln, damit die behandelten Aschen als Dünger eingesetzt werden können. In dem Vortrag wird das Verfahren erklärt, die Düngewirkung dargestellt und Pilotversuche vorgestellt. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 05.11.2018 KW - Thermochemisch KW - Alkalien KW - Dünger KW - Phosphor KW - Upscaling PY - 2018 AN - OPUS4-46602 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute A1 - Mathies, Helena T1 - Transformation of biocides in organic coatings due to UV radiation and water contact N2 - Transformation of carbendazim, diuron, octylisothiazolinone and terbutryn was investigated in two paints containing either white titanium dioxide or a red iron oxide pigment. Test specimens of these coatings on glass were exposed to water contact and UVA-radiation under laboratory conditions. Panels of birch plywood were coated and exposed to natural weather conditions in a field experiment. Concentrations of biocides and transformation products were analysed in leachates from laboratory tests, runoff samples and remaining coatings. Water contact, UVA radiation as well as pigments in the paints affected the pattern and amount of transformation products. T2 - Advanced Coationgs Technology '18 CY - Sosnowiec, Poland DA - 13.11.2018 KW - Biocide KW - Transformation KW - Weathering KW - UV radiation PY - 2018 AN - OPUS4-46648 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Hahn, Oliver A1 - Stege, H. A1 - Oesterle, D. A1 - Bretz, S. A1 - Geiger, G. T1 - Disclosing a new aspect in modern European art: multidisciplinary analysis of modern reverse paintings on glass (1905-1955) N2 - The technique of painting on the reverse side of a glass panel was rediscovered by German artists at the beginning of the 20th century. They appreciated the impressive gloss, luminosity, and depth of colours in this genre. Compared to stained glass, the distinctive properties of this technique are: (1) the paint is applied “cold”, hence, it doesn’t involve a firing step, (2) reverse paintings on glass are framed and always viewed in reflected light and (3) the reverse paint stratigraphy is different from canvas paintings, starting with the front most layer and ending with the backing layer. In 1908 several artists, including Gabriele Münter, Wassily Kandinsky, Heinrich Campendonk, August Macke and Franz Marc of the “Der Blaue Reiter” (the Blue Rider) collective took an interest in this technique and started to share their interest with other colleagues in Europe. Our pioneering project is tracing this transfer of knowledge by a multidisciplinary approach in terms of art history, paint technology and material science. More than 100 artists and >1000 reverse paintings on glass were identified during the project. This high number of objects clearly points out that this technique was by far more important for modern art than previously assumed. In-situ, non-invasive measurements (XRF, Raman, VIS, DRIFTS) on a well-considered selection of 67 paintings reveal the broad palette of colorants ranging from traditional to experimental. Special attention is paid to the impact of synthetic organic pigments (SOP) in artists palette. Demonstrative examples by W. Kandinsky, L. G. Buchheim and F. Jespers are used to discuss analytical challenges and highlights. T2 - Art & Archaeology 2018 CY - Jerusalem, Israel DA - 09.12.2018 KW - Reverse glass painting KW - Spectroscopy KW - In-situ analysis PY - 2018 AN - OPUS4-47042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina A1 - Rabin, Ira A1 - Schlanger, Judith T1 - Quelles informations une approche archéométrique peut-elle nous apporter pour enrichir notre connaissance des manuscrits hébreux et du monde de la Génizah du Caire ? N2 - L'archéométrie est une discipline riche qui peut nous apporter beaucoup d'informations sur l'étude des manuscrits et qui, conjuguée à la paléographie et la codicologie, peut s'apporter un outil précieux pour mieux appréhender les sociétés qui ont produits ces manuscrits. Nous verrons ici quelques exemples de techniques scientifiques non destructives, principalement appliqués à la Génizah du Caire, appliquées à l'étude des manuscrits. T2 - Tagung CY - Paris, France DA - 10.12.2018 KW - XRF KW - Ink KW - Archaeometry KW - Manuscripts KW - Non destructive PY - 2018 AN - OPUS4-47098 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina A1 - Schlanger, J. A1 - Hahn, Oliver A1 - Rabin, Ira T1 - Cairo Genizah documents of the 11th century: analysis of writing materials N2 - The Cairo Geniza is an “archive” discovered in the 19th century in Ben Ezra Synagogue in Fustat, a district in Old Cairo (Egypt). The collection of mostly Jewish documents that vary in genres, languages and writing supports contains a large number of early medieval Hebrew manuscripts. The Geniza provides sources for the literary, linguistic, historical studies of the various aspects Jewish life. As the documents attest, at least two Jewish communities co-existed in Fustat up to 11th century: a so-called Babylonian and Palestinian. These communities had different leaders, different traditions and lived independently. The differences seem to manifest themselves also in the paleographical, codicological and some material properties of the manuscripts produced by each community. The aim of this project is to compare the inks used in the Jewish documents depending on different variables: support (paper, parchment), purpose of the manuscript (legal, private, religious), provenance of the scribe. For the determination of the inks type and composition we had to choose non-invasive, non-destructive and portable techniques to analyze the corpus directly on-situ. The analyses were carried out with a micro-X-ray spectrometer ArtTAX® (Bruker GmbH) and a digital stereomicroscope features built-in LED illumination at 395 nm and 940nm, Dino Lite. We would like to stress that though the methods of material analysis listed above have been successfully employed in the field of cultural heritage and conservation including ancient and medieval manuscripts they have not yet been used to study fragments from the Cairo Genizah. Therefore, we believe that this research project is a pioneering study that will provide new insights into the history of Hebrew writing materials, their production techniques and materials and, thus, contribute new data to the field of Hebrew paleography. T2 - Konferenz Art&Archaeology2018 – 3rd International Conference CY - Jerusalem, Israel DA - 09.12.2018 KW - XRF KW - Ink KW - Manuscripts KW - Cairo Genizah KW - Reflectography PY - 2018 AN - OPUS4-47100 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - Phosphorus recovery from wastewater - Developments and perspective in Germany N2 - A new sewage sludge ordinance was set in force in Germany in 2017 that makes phosphorus recovery from sewage sludge mandatory. The technological possibilities for P-recovery from waste water, sewage sludge and sewage sludge ash were presented. T2 - International Workshop Nutrient Stewardship & Next-Generation Fertilisers CY - Heron Island, Australia DA - 15.12.2018 KW - Phosphorus recovery PY - 2018 AN - OPUS4-47110 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonnerot, Olivier A1 - Bosch, S. A1 - Rabin, Ira A1 - Hahn, Oliver T1 - Scientific service project z02 at the csmc: material-science methods of reconstructing the history of manuscripts N2 - Z02 is one of the three technically supporting projects at the Centre for the Study of Manuscript Cultures (CSMC). In collaboration with the other two service projects, Z01 and Z03, it aims at bridging the gap between humanities and natural sciences and technology. To that purpose, we set up a laboratory with a range of high-end instruments, most of them mobile, allowing thorough non-destructive analysis of manuscripts. In addition to working on constantly improving the laboratory and the methods of analysis, a substantial part of our activities is dedicated to service, by supporting different research projects conducted at the centre. In this talk, we will present our equipment and the possibilities offered by the different techniques available regarding the different kinds of missions: typology and classification of inks, provenance studies, recovery of faded inscriptions and palimpsests, reconstruction of the history of manuscripts, authentication and dating. We will give a brief overview of our past and ongoing activities in the frame of the second phase of the CSMC. Finally, a selection of projects will be presented in greater detail to highlight the possibilities of our laboratory and the diversity of missions which can be carried out. T2 - Konferenz: Art & Archaeology 2018 CY - Jerusalem, Israel DA - 09.12.2018 KW - Manuscripts KW - Inks KW - CSMC KW - Pigments PY - 2018 AN - OPUS4-47039 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piechotta, Christian A1 - Iznaguen, H. A1 - Traub, Heike A1 - Feldmann, Ines A1 - Köppen, Robert A1 - Witt, Angelika A1 - Jung, Christian A1 - Becker, Roland A1 - Oleszak, K. A1 - Bücker, Michael A1 - Urban, Klaus A1 - Reger, Christian A1 - Ostermann, Markus T1 - TF-Projekt MaUS: Material und Umweltsimulation N2 - Gegenstand des Projekts ist die Prüfung der Umweltbeständigkeit und -verträglichkeit von Materialien und Produkten hinsichtlich der Emission von potenziellen Schadstoffen in die Umwelt. Hierzu werden chemisch-physikalische Einflüsse (Bewitterung) und mikrobielle Beanspruchungen an Modellmaterialien evaluiert. So werden die Freisetzungsraten von Schadstoffen in Abhängigkeit der Beanspruchung beschrieben. Als Modellmaterialien kommen die Polymere Polycarbonat, Polytetrafluorethylen, Polystyrol und Polypropylen zum Einsatz. Synergistische Effekte der Bewitterungsparameter und der mikrobiologischen Beanspruchung sollen dabei ebenso betrachtet werden, wie die gezielte Alterung. Auch findet eine Beschreibung des Verhaltens der ausgetragenen Schadstoffe in den Umweltkompartimenten Boden oder Wasser statt. Hier sind mit Hilfe der zu entwickelnden Screening- und non-Target-Analyseverfahren die Transformation und der Metabolismus durch Mikroorganismen zu beschreiben. Aus den Ergebnissen sollen Korrelationen zwischen den künstlichen Alterungsverfahren und realen Szenarien abgeleitet werden, die es gestatten, Schnellprüfverfahren zu etablieren, die die Simulation der realen Beanspruchungen im Zeitraffermodell anwendbar machen. Somit sollen standardisierbare Schnellbeanspruchungs-verfahren erarbeitet werden, die als Prüfeinrichtungen etabliert werden und von externen Auftraggebern zur Prüfung der Umweltbeständigkeit und -verträglichkeit von neuen Materialien genutzt werden können. Die Umweltwirkungen (chemisch-physikalisch und mikrobiologisch) sollen so definiert eingesetzt werden, dass eine reproduzierbare Prüfung möglich wird. Aus diesen Verfahren und Methoden sollen Normen abgeleitet werden, die eine standardisierte Materialprüfung ermöglichen. T2 - Projektmeeting BAM - Covestro CY - Leverkusen, Germany DA - 29.05.2018 KW - Umweltsimulation KW - Schadstoffaustrag PY - 2018 AN - OPUS4-47025 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Buzi, Paola A1 - Rabin, Ira T1 - New approaches to the analysis of ancient inks N2 - 4.5 protocol for ink analysis and new possible fronteers: SERS and ASAP-MS. T2 - Art and Archaeology conference - Jerusalem CY - Jerusalem, Israel DA - 10.12.2018 KW - ASAP-MS KW - Ancient INKS KW - NIR reflectography KW - XRF KW - SERS PY - 2018 AN - OPUS4-47080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - McMahon, Dino Peter T1 - Evolution, recombination and virulence of emerging bee viruses N2 - Bee populations have declined significantly in recent years and this is thought to be attributable at least in part to the (re-)emergence of viruses. These viruses are predominantly positive single stranded (+ss) RNA viruses belonging to the Picornavirales. Managed honeybees are often infested with the invasive mite, Varroa destructor, which vectors RNA viruses including Deformed wing virus (DWV, family Iflaviridae): a leading culprit of colony losses. Many bee viruses have been sequenced and structural features are now available for viruses such as DWV. DWV consists of at least 3 distinct genotypes, two of which have been shown to be differentially virulent in honeybees. Molecular studies have demonstrated that DWV has a mean evolutionary rate of 1.35 x 10-3 per site per year. For such viruses – in contrast to their eukaryotic hosts – ecological and evolutionary timescales significantly overlap. This rapid evolution allows RNA viruses to adapt quickly to novel host environments with recombination representing an additional key source of genetic variation. Interestingly, recombination between genotypes of DWV has recently been shown to be a common occurrence in honeybees. A challenge has been to develop bioinformatics tools that can accurately reconstruct viral haplotypes – including recombinants – from heterogenous high-throughput sequence data. The impact of blood-to-blood Varroa destructor transmission on virus evolution represents an important question in bee virus research. Due to the nature of the V. destructor life cycle, predictions can be made about the potential impact of the mite on virus virulence evolution. Specifically, the developing honeybee host pupa should remain alive until close to the completion of metamorphosis to provide sufficient time for successful mite reproduction, including offspring mating. For optimal transmission, any virus found in a mature and mated daughter mite will hold a significant selective advantage over a virus found in an immature or unmated daughter mite – placing a cost on virus virulence that impacts honeybee pupae before mites can mate. On the other side, viruses replicating too slowly and with delayed virulence effects will hold a selective handicap because fewer transmission units will be found in mated mites. I have hypothesized that the evolution of virus virulence shifted following the arrival of V. destructor, with viruses, including recombinants and/or specific viral genotypes being selected for a level of virulence in pupae (and likely also in adults) that maximises R0, which represents the basic reproductive number of the virus in the host population. R0 is defined by the number of subsequent infections caused by a single infection and it must be greater than 1 for an infection to spread in a population. It is enhanced by maximising the number of transmission units passed to uninfected susceptible vectors, and ultimately hosts (Figure 1). Honeybee viruses are also shared with sympatric wild bees and viral prevalence and sequence data indicate frequent virus transmission between managed and wild bee species. In addition to infecting the western honeybee (Apis mellifera), DWV can infect other Asian honeybee species such as Apis ceranae. Outside of honeybees, DWV has been found widely in bumblebees, including solitary bees and wasps and there is evidence that it can actively replicate in several Bombus and solitary bee species. Whether the arrival of the V. destructor mite in A. mellifera has driven viral emergence in non-Apis bees is a target of ongoing research. T2 - 2nd European Virus Bioinformatics Centre (EVBC) conference CY - Utrecht, Netherlands DA - 09.05.2018 KW - Virus KW - Virulence KW - Bees PY - 2018 AN - OPUS4-47155 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -