TY - CONF A1 - Tang, Chi-Long T1 - Proposal of a standard test method for the quantification of particulate matter during 3D printing and the systematic ranking of filament materials N2 - The diversity of fused filament fabrication (FFF) filaments continues to grow rapidly as the popularity of FFF-3D desktop printers for the use as home fabrication devices has been greatly increased in the past decade. Potential harmful emissions and associated health risks when operating indoors have induced many emission studies. However, the lack of standardization of measurements impeded an objectifiable comparison of research findings. Therefore, we designed a chamber-based standard method, i.e., the strand printing method (SPM), which provides a standardized printing procedure and quantifies systematically the particle emission released from individual FFF-3D filaments under controlled conditions. Forty-four marketable filament products were tested. The total number of emitted particles (TP) varied by approximately four orders of magnitude (1E9 ≤ TP ≤ 1E13), indicating that origin of polymers, manufacturer-specific additives, and undeclared impurities have a strong influence. Our results suggest that TP characterizes an individual filament product and particle emissions cannot be categorized by the polymer type (e.g., PLA or ABS) alone. The user's choice of a filament product is therefore decisive for the exposure to released particles during operation. Thus, choosing a filament product awarded for low emissions seems to be an easily achievable preemptive measure to prevent health hazards. T2 - 11th International Aerosol Conference CY - Athens, Greece DA - 04.09.2022 KW - Ultrafine particles KW - FFF-3D-Printer KW - Indoor emission KW - Emission test chamber KW - Test method KW - Exposure risk PY - 2022 AN - OPUS4-55666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long T1 - UFP-Emission beim 3D-Druck N2 - Desktop-3D-Drucker haben in der letzten Dekade große Popularität in Bildungseinrichtungen, kleinen Unternehmen und Privathaushalten erlangt. Weit verbreitet ist mittlerweile die „Fused Filament Fabrication (FFF)“ Technologie. Hier wird ein thermoplastisches Filament geschmolzen, durch eine Metalldüse extrudiert und anschließend schichtweise so auf ein Druckbett aufgetragen, dass ein 3D-Objekt entsteht. Das Filamentmaterial wird dabei thermisch stark belastet, was zur Emission von Aerosolen sowie flüchtigen organischen Verbindungen (VOC) führt. Dabei werden hauptsächlich ultrafeine Partikel (UFP, dP < 100 nm) freigesetzt werden, die sogar in manchen Fällen im sub-4nm Größenbereich einen signifikanten Anteil ausmachen können (Tang und Seeger 2024). Die gesundheitliche Relevanz eingeatmeter UFP ist durch sehr viele Studien gut belegt. Während eines i.d.R. mehrstündigen FFF-Druckvorgangs wird ein Anwender mit diesen Luftschadstoffen im Innenraum exponiert, häufig ohne eine Einschätzung des damit verbundenen Risikos zu haben. Die Exposition kann durch technische Faktoren (z.B. Druckerausstattung und -einstellung, Innenraumventilation), aber auch erheblich durch die Filamentauswahl beeinflusst werden. Unser Vorschlag zur Risikominderung besteht in der Auszeichnung emissionsarmer Filamentprodukte mit dem Umweltzeichen „Blauer Engel“, um so den Verbrauchern eine fundierte Auswahl zu ermöglichen. In unserem Projekt entwickeln wir dafür ein kammerbasiertes, standardisierbares und robustes Prüfverfahren zur vergleichenden Messung der Emission aus Filamenten. Mit dem Strangdruck-Verfahren (engl. Strand Printing Method, SPM) wird eine festgelegte Filamentlänge mit konstanter Rate extrudiert und auf dem Druckbett abgelegt, ohne dabei ein 3D-Objekt aufzubauen. Diese Vorgehensweise reduziert den Einfluss experimentell schlecht zu kontrollierender Faktoren sowie die Ausfallquote. Eine detaillierte Beschreibung und die Vorteile von SPM werden in Tang und Seeger (2022) erläutert. SPM wurde bereits für 44 Filamentprodukte aus unterschiedlichen Polymeren und Additiven als Vergleichstest angewendet. Alle Messungen wurden in einer klimatisierten 1 m³-Emissionsprüfkammer durchgeführt. Die Gesamtanzahl der emittierten Partikel (TP) dient als Beurteilungsmaß, in Anlehnung an die Vergabegrundlage DE-UZ-219 des Umweltzeichens Blauer Engel für Laserdrucker. Unter den getesteten Filamentprodukten variiert TP um ca. vier Größenordnungen (1E+9 ≤ TP ≤ 1E+13). Auch innerhalb jeder der untersuchten Polymergruppen variierte TP signifikant. Die Partikelemission kann daher nicht allein nach dem Basispolymer kategorisiert werden. Unsere Resultate belegen, dass die Stärke der Partikelemission eher eine charakteristische und individuelle Eigenschaft eines Filamentproduktes ist. Die Herkunft der Polymere, die herstellerspezifischen Additive sowie die nicht deklarierte Verunreinigungen können einen starken Einfluss auf die Emission haben. Die Auszeichnung von emissionsarmen Filament-produkten verspricht somit eine einfache, aber effektive Maßnahme zu sein, um Verbrauchern eine Minderung des Expositionsrisikos beim FFF-3D-Druck zu ermöglichen. T2 - 5. Symposium "Ultrafeinstaub in der Atmosphäre und in Innenräumen" CY - Berlin, Germany DA - 16.09.2024 KW - 3D-Druck KW - Ultrafeine Partikel KW - Innenraumemission KW - Luftschadstoffe KW - Emissionsprüfung PY - 2024 AN - OPUS4-61067 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long T1 - Minimizing the FFF-3D printer hardware bias on particle emission by adjustment of the set extruder temperature N2 - Fused filament fabrication (FFF) on desktop 3D printers is a material extrusion-based technique often used by educational institutions, small enterprises and private households. Polymeric filaments are melted and extruded through a heated nozzle to form a 3D object in layers. The extrusion temperature is therefore a key parameter for a successful print job, but also one of the main driving factors for the emission of harmful air pollutants, namely ultrafine particles and volatile organic gases, which are formed by thermal stress on the polymeric feedstock. The awareness of potential health risks has increased the number of emission studies in the past years. However, the multiplicity of study designs makes an objective comparison of emission data challenging because printer hardware factors such as the actual extruder temperature (TE) and also feedstockspecific emissions are not considered. We assume that across the market of commercial low- and mid-price FFF printers substantial deviations between actual and set extruder temperatures exist, which have a strong effect on the emissions and hence may bias the findings of exposure studies. In our last publication, we presented a standardized feedstock-specific emission test method and showed that for each investigated feedstock an increase in actual extruder temperature was accompanied by an increase in particle emissions (Tang and Seeger, 2022). Therefore, any systematic discrepancy between set and actual extruder temperature matters. In this study, we used a thermocouple and an infrared camera to measure the actual extruder temperatures at different heights. We found significant under- and overestimation of the actual extruder temperatures by the respective set temperatures in three commercial printers. This caused a broad variation of the measured total numbers of emitted particles (TP), even when the same feedstock was operated. For the determination of TP, we followed the DE-UZ 219 test guideline. In a second round we repeated the tests with all printers adjusted to exactly the same extruder temperatures, i.e., to TE=230°C for ABS and TE=210°C for PLA. All measurements were conducted in a 1 m³ emission test chamber. Particle emissions in the size range between 4 nm and 20 μm were detected. Printing on three different printer models without temperature adjustment resulted for each of the investigated feedstocks in a variation in TP of around two orders of magnitude. After temperature adjustment, this was substantially reduced to approx. one order of magnitude and hence minimizes the bias of printer hardware on the emissions. Our findings suggest that adjustment of the extruder temperature should be mandatory in emission testing standards. It also poses a more accurate benchmark and provides more reliable emission data for evaluation of indoor air quality or for health risk assessments. In addition, a proper temperature setting is in the interest of the user. Some commercial FFF printers may have a higher actual extruder temperature than displayed and unintended overheating may not only impair the print quality but may cause unnecessarily increased exposure to particle emissions. T2 - European Aerosol Conference 2023 CY - Málaga, Spain DA - 03.09.2023 KW - Ultrafine particles KW - Thermal imaging KW - 3D printing KW - Indoor air quality KW - Emission testing PY - 2023 AN - OPUS4-58258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Susset, Bernd A1 - Kalbe, Ute T1 - Spezifische Herausforderungen bei der PFAS-Elution N2 - Im Teil des Workshops, der sich mit Praxiserfahrungen zu den Elutionsverfahren DIN 19528 und DIN 19529 befasste, wurden spezifische Herausforderungen bei Elutionsuntersuchungen von Bodenproben mit einer PFAS-Kontamination vorgestellt. Aus durchgeführten Robustheitsuntersuchungen im ZAG der Universität Tübingen sowie in der BAM wurden praxisrelevante Schlussfolgerungen erläutert und für einzelne PFAS-Verbindungen und Vorläufersubstanzen konkretisiert. Dabei wurde auch auf die Vergleichbarkeit von Schüttel- und Säulenversuchen beim bewertungsrelevanten Wasser/Feststoff-Verhältnis von 2 l/kg und die Bedeutung des Fest/Flüssigtrennschrittes beim Schüttelverfahren eingegangen. Die Untersuchung von Böden auf PFAS mit Elutionsversuchen ist generell möglich, aber es besteht eine komplexe Abhängigkeit der Konzentrationen im Eluat vom Gesamtgehalt, der Löslichkeit und des Verteilungsmusters der einzelnen PFAS, der Art der Bodenmatrix und dem Einfluss der Probenaufbereitung vor der Analytik. Die geringere Sensitivität der Feststoffanalytik für PFAS im Vergleich zur Eluatanalytik erschwert die Berechnung von Massenbilanzen. T2 - Workshop / Anwendertreffen Elutionsverfahren im Regelungsbereich der Mantelverordnung (ErsatzbaustoffV / BBodSchV) und der EU-BauPVO CY - Berlin, Germany DA - 07.05.2024 KW - Elution KW - PFAS KW - Prekursoren KW - Boden KW - Säulenversuch KW - Schüttelversuch PY - 2024 AN - OPUS4-62065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon T1 - Spectroscopic analysis of colourants and binders of Chinese reverse glass paintings tracing a cultural dialogue N2 - Scientific analysis based on spectroscopic methods provide essential information on the composition of colourants and binders in paintings. These results can be set in a historical context and help to confirm art historical interpretations. Proofs of certain pigments can be used for dating purposes and may reveal if the artist used not only local but also imported materials. A pilot study of two Chinese reverse glass paintings from the late 19th (Yingying and Hongniang) and early 20th centuries (The Archer) was performed using a multi-analytical approach including X-ray fluorescence (XRF), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and Raman spectroscopy. This approach allowed the identification of the pigments and the classification of the binding media. The results reveal a combined use of traditional Chinese and imported European materials. Several pigments like cinnabar, lead white, orpiment, carbon black and copper-arsenic green (probably emerald green) were found in both paintings; red lead, artificial ultramarine blue, Prussian blue and ochre appear in at least one of the paintings. The proof of limewash (calcite and small amounts of portlandite) as a backing layer in “Yingying and Hongniang” indicates that clamshell white was also used for reverse glass paintings. Drying oil was classified as a binding media in most areas of both paintings. However, the orange background of The Archer yielded prominent bands of both proteinaceous and fatty binder. T2 - China and the West Reconsidering Chinese Reverse Glass Painting CY - Romont, Switzerland DA - 14.02.2020 KW - Reverse glass painting KW - DRIFTS KW - Raman spectroscopy PY - 2020 AN - OPUS4-50445 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz T1 - Solution-driven processing of calcium sulfate: the mechanism of the reversible transformation of gypsum to bassanite in brines N2 - Calcium sulfate hemihydrate (CaSO4ᐧ0.5H2O), also known as bassanite, has been used as a precursor to produce gypsum (dihydrate, CaSO4ᐧ2H2O) for various construction and decorative purposes since prehistoric times. The main route to obtain hemihydrate is a thermal treatment of gypsum at temperatures typically between 150 °C and 200 °C to remove some of the structural water. In this contribution, we introduce (Fig. 1) a more efficient and sustainable method (T < 100 °C) that enables the direct, rapid, and reversibly conversion of gypsum to bassanite using reusable high salinity aqueous solutions (brines with c[NaCl] > 4 M). The optimum conditions for the efficientproduction of bassanite in a short time (< 5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the typical behaviour of the bassanite phase in low salt environments. Traditionally, hemihydrate is obtained through a solid state thermal treatment because bassanite is considered to be metastable with respect to gypsum and anhydrite in aqueous solutions, and therefore gypsum-to-bassanite conversion should not occur in water. Its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures is inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline structure for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios. T2 - Granada Münster Discussion Meeting GMDM 10 CY - Münster, Germany DA - 29.11.2023 KW - Gypsum KW - Bassanite KW - Calcium sulfate KW - Recycling KW - Scattering PY - 2024 AN - OPUS4-59162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Souza Filho, I. A1 - Adam, Christian T1 - Fundamentals of the hydrogen plasma reduction of iron ores N2 - Hydrogen plasma treatment of iron ores or iron oxide containing wastes can be an efficient option to produce green iron e.g. for steel production. This way iron oxide is reduced to metallic iron in the liquid form by the highly reactive species that are formed in a hydrogen plasma. Hydrogen plasma can be used at the same time to remove undesired gangue elements. The presentation shows the experimental setup, shows first results of iron ore reduction by hydrogen plasma and gives an outlook for industrial application of the technology. T2 - European Academic Symposium on EAF steelmaking (EASES 2023) CY - Oulu, Finland DA - 05.06.2023 KW - Hydrogen KW - Plasma KW - Reduction PY - 2023 AN - OPUS4-57626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Song, Jessica T1 - (micro)Plastic biofilms: Keeping afloat by carving out a new niche N2 - As pervasive and persistent pollutants, microplastics exist alongside vast microbial communities in nature. These hardy substrates accumulate rich polymeric matrices from their surroundings that in turn offer nutrition and protection to diverse communities and their theatre of activity, representing a new ecological niche. In our research to date, biofilm communities demonstrate no specificity to plastic polymers but appear rather to be more strongly shaped by spatial and temporal factors. Other synthetic substrates such as tyre wear, however, signal towards some form of community selection that may manifest in the presence of leachates from the polymer itself. Contrary to these biofilms, polyaromatic hydrocarbons appear to observe the opposite pattern, with adsorbed concentrations on plastic more strongly dictated by the type of plastic polymer than the environment itself. Although community specificity has not yet been evidenced among different plastic polymers, our studies show that microplastics might shape communities in a different way. As suggested by our detection of carotenoid synthesis pathways and photosynthetic gene clusters among microplastic biofilms, we postulate this new niche to shape a specific functional toolkit adaptive among its members as a product of prolonged exposure to UV radiation at the sea’s surface. This opens exciting new avenues for further research into the functional capabilities of these biofilms and offers new perspective on their potential beyond subordinate processes such as biodegradation. Here, we present a synthesis of our collective research on microplastic biofilms, the factors that shape them, and their interactions with nature. T2 - MICRO 2024 Conference CY - Lanzarote, Spain DA - 23.09.2024 KW - Biofilms KW - Microplastics KW - Microbial ecology KW - 16S amplicon KW - Pollutants PY - 2024 AN - OPUS4-61990 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Song, Jessica T1 - Close encounters on a micro scale: Dynamics and interactions of microplastic biofilms in aquatic ecosystems. N2 - Microplastics circulate freely throughout aquatic ecosystems and, due to their interactive nature, accumulate complex polymeric matrices consisting of rich organic compounds and inorganic pollutants. Simultaneously, these hardy substrates offer nutrition and protection to diverse microbial communities and their theatre of activity, representing a new ecological niche. In our work, we investigate the interactions of microplastics in aquatic systems and characterise the effects of these interactions on associated microbial communities to better understand how these substrates might impact surrounding ecosystems. Demonstrating no specificity to polymer type, microplastic biofilms are shaped more by the strong influence of spatial and temporal factors. Microplastic sorption of polycyclic aromatic hydrocarbons (PAHs), in contrast, appear to be more strongly dictated by substrate type, with different polymers observed to sorb varying levels of different PAHs. These interactions between the different emerging contaminants were found in our study to have a significant effect on associated substrate biofilms. Elevated levels of specific 3- and 4-ring PAHs on polyethylene and polystyrene were found to coincide with a notable shift in community composition and structure, as well as a reduced diversity among biofilm communities. The findings in our study illustrate the importance of investigating the collective effect of pollutants in combination and their complex interactions in assessing their environmental impact. To fully understand how microplastics interact and alter surrounding ecosystems, the entire substrate must be considered, including all chemicals integrated into the polymeric matrix. T2 - Biofilms 11 Conference CY - Cardiff, Wales, UK DA - 13.05.2025 KW - Microplastics KW - Biofilms KW - PAHs PY - 2025 AN - OPUS4-63389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobisch, Lydia-Yasmin T1 - Identification of Genes Involved in Susceptibility to Biocides in Sulfate-Reducing Bacteria N2 - Microbially induced corrosion (MIC) poses a significant challenge in various industries, leading to structural damage and economic losses due to the activity of microorganisms on metal surfaces. The major culprits of MIC are the sulfate-reducing bacteria (SRB). A common mitigation method is the usage of biocides to prevent MIC. However, the molecular mechanisms that determine susceptibility of SRB to biocides have been poorly understood. Our aim is to identify genes that are linked to biocide susceptibility in the model SRB strain Oleidesulfovibrio alaskensis (G20). We investigated the susceptibility of G20 towards three biocides commonly used in MIC protection: benzalkonium chloride (BAC), glutaraldehyde (GTA), and tetrakishydroxymethyl phosphonium sulphate (THPS). We determined selection of mutants in specific genes in two G20 barcoded transposon mutant libraries in the presence of these biocides and media as control along a concentration gradient up to 500 ppm. Our study investigated over 1843 genes in G20, revealing insights into their response to biocide treatments. We identified 1668 genes negatively affected by biocide treatment, while 175 genes showed improved fitness. Among the treatments leading to reduced fitness in the mutants, GTA had the highest number of solely negatively affected genes (186), followed by BAC (67) and THPS (69). There were common negative impacts on 280 genes of all four treatments (BAC, GTA, THPS, control). Notably, BAC and GTA shared 113 affected genes, BAC and THPS shared 59, and GTA and THPS shared 72. On the single gene level, mutants treated with THPS exhibited reduced fitness for the rluD gene (DDE_1447), encoding ribosomal large subunit pseudouridine synthase d, which plays a crucial role in protein biosynthesis. In the presence of BAC, mutants showed reduced fitness due to the lack of the acrB gene (DDE_0401), encoding a cationic efflux pump crucial for biocide resistance. Our findings provide leads for future research into the detailed molecular mechanisms that underlie biocide susceptibility in microorganisms responsible for MIC. Such detailed understanding will enable the development of improved MIC prevention strategies and foster a more sustainable use of biocides. T2 - International Biodeterioration and Biodegradation Symposium CY - Berlin, Germany DA - 09.09.2024 KW - Biocide Resistance KW - Transposon Mutant Libraries KW - Sulfate-Reducing Bacteria (SRB) KW - Microbially Induced Corrosion (MIC) PY - 2024 AN - OPUS4-61526 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobisch, Lydia-Yasmin T1 - Biocide resistance evolution of corrosion causing sulfate reducing bacteria N2 - SRB are environmentally and industrially important microorganisms. The disadvantage of their metabolic activity (e.g. sulfate reduction) results in the formation of toxic sulfide that leads to microbial influenced corrosion. SRB have been responsible for biocorrosion of ferrous metal. One of mitigation strategy is the use of biocides. However, it has been shown that various bacteria develop antimicrobial resistance due to excessive use of biocides. Thus, a deeper understanding of the evolution of biocide resistance of SRB is necessary. Three commonly used biocides, THPS, BAC, and GLUT were applied to investigate the susceptibility of Desulfovibrio alaskensis G20.The minimum inhibitory and bactericidal concentration and the killing kinetics of the three biocides was determined. These results will be used to conduct evolution experiments to determine the evolution of resistance towards biocides of SRBs. The outcome of this work can be helpful to improve the management of MIC treatments. T2 - Panel, Pitch & Popcorn by EUROMIC CY - Online meeting DA - 21.06.2021 KW - Biocide KW - Evolution KW - Mircobially influcenced corrosion KW - Sulfate reducing bacteria PY - 2021 AN - OPUS4-56940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Wiedergewinnung von Rohstoffen aus Abfall N2 - Antimon (Sb) wird in Industrieprodukten hauptsächlich als Flammschutzmittel in Kunststoff verwendet. Aufgrund solcher Zusätze in Kunststoffen landet etwa die Hälfte von Sb am Ende der Lebensdauer in der Verbrennung fester Siedlungsabfälle und folglich in relevanten Mengen in der erzeugten Bodenasche. Bei Kontakt mit Wasser ist die anfängliche Auslaugbarkeit gering, da Antimonat mit Ca2+ schwerlösliche Verbindungen bilden. Nach der Carnonatisierung der Verbrennungsasche (IBA) während der fortschreitenden Alterung nimmt der pH-Wert in den Sickerwasser ab. Mit abnehmender Ca-Konzentration im Eluat ändert sich das Lösungsgleichgewicht und Antimonate lösen sich auf. In Deutschland ist beabsichtigt, Sb in IBA mit der geplanten Umsetzung der sogenannten Mantelverordnung (MantelVO, die Bestimmungen zur Verwertung von Mineralabfällen enthält) in naher Zukunft zu regulieren. Die im Entwurf festgelegten Grenzwerte können für IBA kritisch sein und stellen daher ein Risiko für die Verwendung der Mineralfraktion von IBA in den gut etablierten Recyclingwegen dar. T2 - Weiterbildung für Efb-Sachverständige, Mitarbeiter von Entsorgungsunternehmen und Umweltbehörden (GUT GmbH) CY - Online Meeting DA - 07.01.2021 KW - Rostasche KW - Antimon KW - Auslaugverfahren PY - 2021 AN - OPUS4-52438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Product testing and performance N2 - Geosynthetic materials are applied in measures for coastal protection. Weathering or any damage of constructions, as shown by a field study in Kaliningrad Oblast (Russia), could lead to the littering of the beach or the sea (marine littering) and the discharge of possibly harmful additives into the marine environment. The ageing behavior of a widely used geotextile made of polypropylene was studied by artificial accelerated ageing in water-filled autoclaves at temperatures of 30 to 80° C and pressures of 10 to 50 bar. Tensile strength tests were used to evaluate the progress of ageing, concluding that temperature rather than pressure was the main factor influencing the ageing of geotextiles. Using a modified Arrhenius equation, it was possible to calculate the half-life for the loss of 50% of the strain, which corresponds to approximately 330 years. T2 - EuroGeo-7, Session Geosynthetics, Sustainability and Current Industry Challenges CY - Warschau, Poland DA - 04.09.2022 KW - Geosynthetics KW - Ageing KW - Autoclave tests PY - 2022 AN - OPUS4-55671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Das ERA-MIN 2 Projekt BASH-TREAT N2 - Im Rahmen des Projekts wurde 1.) eine vollständige Bewertung des Stands der Technik in der EU bei der Behandlung von Rostasche vorgenommen und 2.) eine Optimierung der Nutzung der Feinfraktion in Labor- und Feldmaßstab untersucht. Das Konsortium bestand aus zwei Universitäten aus Deutschland und Italien, der BAM als Forschungseinrichtung des Bundes und zwei Industriepartnern aus Deutschland und Schweden mit unterschiedlichen und spezifischen Fachkompetenzen. Im Vortrag werden die Ergebnisse des weitgehend abgeschlossenen Projekts BASH-TREAT vorgestellt. T2 - Jahrestreffen der ProcessNet-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung, Energieverfahrenstechnik, Gasreinigung, Hochtemperaturtechnik, Rohstoffe CY - Bamberg, Germany DA - 30.03.2022 KW - Rostasche KW - Thermische Abfallbehandlung KW - Nassaufbereitung PY - 2022 AN - OPUS4-54589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Aschen und Schlacken aus der Abfallverbrennung; Gefährlich oder nicht? N2 - In Deutschland fallen aktuell pro Jahr über 5 Mio. Tonnen Hausmüllverbrennungs-aschen (HMVA) an. Eine Verwertung dieser Aschen und Schlacken ist in Deutschland möglich und findet überwiegend im Deponiebau statt. Für die Verwertung sind in der Ersatzbaustoffverordnung Eluatgrenzwerte für Schwermetalle und einige andere Parameter vorgesehen. Der Umgang mit HMVA könnte durch eine Einstufung als gefährlicher Abfall erschwert werden. Maßgeblich für die Einstufung eines Abfalls als gefährlich oder ungefährlich sind die gefahrenrelevanten Eigenschaften HP 1 bis HP 15 nach Anhang III der Richtlinie 2008/98/EG über Abfälle mit dort festgelegten Konzentrationsgrenzen. Für HMVA ist im Wesentlichen nur der Parameter HP 14 (Ökotoxizität) von Bedeutung. Dafür sind entscheidend die Gehalte an chemischen Verbindungen mit den Gefahrenhinweiscodes (hazard statement code, HSC) H400, H410, H411, H412 und H413. Eine detaillierte Diskussion zu den übrigen Gefahreneigenschaften bei HMVA findet sich in der Literatur. Die Einstufung als gefährlicher Abfall erfolgt nach festgelegten Rechenregeln. Die BAM bearbeitet ein durch das UBA gefördertes Forschungsprojekt zur Erfassung und Bewertung von Analysedaten zu Aschen und Schlacken aus Abfallverbrennungsanlagen. Die Ergebnisse des Vorhabens sollen bei der Weiterentwicklung des vorhandenen Konzeptes für eine bundeseinheitlichen Untersuchung und abfallrechtlichen Einordnung von Aschen und Schlacken aus deutschen Abfallverbrennungsanlagen unterstützend herangezogen werden. Im Vortrag werden Verfahren zur quantitativen Bestimmung der einstufungsrelevanten Verbindungen vorgestellt: 1.) der Praxisleitfaden von ITAD und IGAM, 2.) Methode basierend auf der Bioverfügbarkeit und 3.) Methode basierend auf Speziierungsanalyse. T2 - Jahrestreffen 2023 der DECHEMA-Fachgruppen AuW und TRO CY - Dresden, Germany DA - 06.03.2023 KW - Rostasche KW - Speziierungsanalyse KW - Abfallbehandlung PY - 2023 AN - OPUS4-57346 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Secondary building materials in a circular economy N2 - Half of the global material consumption is mineral material. The circularity is still low so that enhanced use of secondary building material is required to close loops. Three different secondary building materials are discussed based on exemplary research results: construction and demolition waste (C&D waste), soil-like material and incineration bottom ash (IBA). Focus was laid on the environmental compatibility of the materials examined mainly by standardized leaching tests. C&D waste was investigated after a wet treatment using a jigging machine, soil-like material and IBA were characterized with respect to their material composition. The environmental compatibility in particular was studied using standard leaching tests (batch tests and column tests). It was concluded that soil-like material can mostly be utilized even when the precautionary limit values set are exceeded by a factor of less than 2. For C&D waste the fine fraction below 2 mm and the content of brick material is problematic. IBA fulfills quality level HMVA-2 following German regulation. Higher quality levels of utilization might be achievable with better treatment technologies. T2 - 15th International Conference on Ecomaterials (ICEM15) CY - Iki, Japan DA - 26.11.2023 KW - Secondary building materials KW - Incineration bottom ash KW - Construction and demolition waste KW - Soil-like material PY - 2023 AN - OPUS4-59186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Aschen und Schlacken aus der Abfallverbrennung im Lichte der Ersatzbaustoffverordnung N2 - Im Rahmen eines vom Umweltbundesamt geförderten Forschungsprojekts wurde untersucht, ob die Abtrennung der Feinfraktion (0-2 mm) eine Verbesserung der umweltrelevanten Eigenschaften bewirkt und somit HMVA-1 erreicht werden kann. In Deutschland wird die Rostasche durch Nassentschlackungssysteme aus dem Feuerraum ausgetragen. Durch den Kontakt mit Wasser setzen direkt hydraulische Reaktionen ein, die eine vollständige Abtrennung der Feinfraktion unmöglich machen. Das wurde bereits in den 1990er Jahren erkannt und führte zur Entwicklung des ABB InRec Verfahrens mit Trockenentaschung als ersten Verfahrensschritt. Auch damals war das Ziel eine möglichst inerte Rostasche für die Verwertung zu erzeugen. In den letzten Jahren wurden in der Schweiz Trockenentaschungssystem installiert, hier vor allem um die Rückgewinnung von elementaren Metallen auch in der Feinfraktion zu verbessern. Welche Potenziale sich dabei erschließen lassen, wurde in einem anderen UBA-Projekt untersucht. Im Rahmen unserer Arbeiten wurde versuchsweise trockene Rostasche an einer Anlage in Süddeutschland genommen und im Labor untersucht. Im Vortrag werden die Ergebnisse zum Auslaugverhalten und zur Gefahreneigenschaft HP14 (Ökotoxizität) vorgestellt. T2 - Jahrestreffen 2024 der DECHEMA-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung (AuW) und Gasreinigung (GAS) CY - Dresden, Germany DA - 25.03.2024 KW - Rostasche KW - Ersatzbaustoffe PY - 2024 AN - OPUS4-59985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Detektion, Quantifizierung und Entfernung von insbesondere ultrakurzkettigen PFAS in Grundwasser N2 - Da PFAS in großem Umfang in einer Vielzahl von Produkten verwendet wurde, sind sie im Grundwasser in der Nähe vieler industrieller und militärischer Anlagen weltweit zu finden. Darüber hinaus führten neue Vorschriften und Beschränkungen für die Verwendung von langkettigen PFAS zu einer vermehrten Produktion kurzkettiger Alternativen. Ultrakurzkettige PFAS (≥C3) können natürliche und anthropogene Barrieren durchdringen und schließlich in Trinkwasserquellen gelangen. Zudem entfernen die meisten gängigen Trinkwasser-aufbereitungsverfahren die ultrakurzkettigen PFAS nicht ausreichend. Im Kooperationsprojekt DEFEAT-PFAS wird daher das Ziel verfolgt, Wissenslücken über Nachweis, Quantifizierung und Entfernung von kurz- (C4-C7) und ultrakurzkettige (C1-C3) PFAS, in kontaminiertem Grundwasser zu schließen. Die israelischen und deutschen Projektpartner entwickeln dafür analytische Methoden and selektive Passivsammler, um das zeitliche Profil von PFAS-Spezies im Grundwasser zu erfassen und überwachen. Darüber hinaus ein zweistufiges Verfahren entwickelt, welches darauf ausgelegt ist, die relativ niedrigen PFAS-Konzentrationen im Grundwasser durch neuartige Membranverfahren, Umkehrosmose im Batchbetrieb mit geschlossenem Kreislauf sowie Verbund-Nanofiltrationsmembranen, zu konzentrieren. Anschließend werden die PFAS angereicherten Konzentrate mittels Koagulation behandelt und das verbleibende PFAS an kohlenstoffhaltigen Nanomaterialien adsorbiert. T2 - Workshop des Netzwerks Perflusan CY - Karlsruhe, Germany DA - 18.06.2024 KW - Grundwasser KW - Per- und Polyfluoroierte Alkylsubstanzen (PFAS) PY - 2024 AN - OPUS4-60334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Einstufung von Aschen und Schlacken aus der Abfallverbrennung im Hinblick auf die weitere Verwertung – Handlungsempfehlungen N2 - Die Einstufung von Hausmüllverbrennungsasche (HMVA) als gefährlich oder nicht gefährlich nach der Gefahreneigenschaft HP14 (ökotoxisch) ist nach wie vor umstritten, da es noch keine allgemein anerkannten Methoden zur Bewertung gibt. Wenn die Berechnungsregeln angewendet werden sollen angewendet werden sollen, sind Kenntnisse über die chemische Zusammensetzung von HMVA erforderlich. Informationen über die chemische Zusammensetzung von HMVA können mit einem Ansatz gewonnen werden, der auf der Gruppierung von Substanzen. Für HMVA können vier Stoffgruppen definiert werden: 1. elementare und legierte Metalle, 2. leicht wasserlösliche Stoffe, 3. schwer lösliche Stoffe und 4. Stoffe mit starken chemischen Bindungen. Elementares und legiertes Cu und Zn sind in der HMVA vorhanden und werden in der Regel als Nichteisenmetallfraktion zurückgewonnen, zumindest die größeren Partikel. Zn-Partikel, die kleiner als 1 mm sind, werden als H410 eingestuft, feine Partikel von Cu nur als H411. Die wasserlösliche Fraktion kann mit Standardauslaugungsmethoden quantifiziert werden Auslaugungsmethoden quantifiziert werden, z. B. bei einem Flüssigkeits-Feststoff-Verhältnis (L/S) von 2 oder 10 l/kg. Sowohl die Sulfate von Zn als auch von Cu gehören zu dieser Gruppe. In einer neueren Veröffentlichung wurde gezeigt, dass bei den oben genannten Metalle die ausgelaugte Menge weit unter dem Grenzwert von 1.000 mg/kg liegt, selbst wenn stöchiometrische Faktoren angewendet werden. Stoffgruppe 3 sind potenzielle H410-Stoffe. Dabei handelt es sich um Carbonate, Hydroxide und Oxide der betreffenden Elemente, die löslich sind in schwachen organischen Säuren wie Essigsäure löslich sind. Die Worst-Case-Stoffe der Gruppe 3, d. h. die Verbindungen mit den höchsten stöchiometrischen Faktoren, sind CuCO3xCu(OH)2 und ZnO. Stoffe mit starken chemischen Bindungen wie Silikate oder Sulfide sind nur löslich in starken Säuren (z.B. Königswasser) löslich und haben keinen Ökotoxizitäts-Gefahrencode. Das Mobilisierungsverhalten der relevanten Schwermetalle und damit der Gruppe der schwer schwerlöslichen Verbindungen kann mit der 4-stufigen sequenziellen Extraktion untersucht werden. Für die HP14 Einstufung könnte auch eine einstufige Extraktion ausreichend sein. Nur die Elemente Zn und Cu sind für die HP14-Einstufung der HMVA von Bedeutung, da die Feststoffgehalte aller anderen Schwermetalle unterhalb des Feststoffgehalte aller anderen Schwermetalle unter der Cut-Off-Grenze von 0,1 % liegen, selbst wenn man sie in chemischen Verbindungen mit stöchiometrischen Faktoren. Im Ergebnis wurde gezeigt, dass HMVA in der Regel als nicht gefährlich einzustufen ist. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2024 KW - Rostasche KW - Ökotoxizität KW - Sequenzielle Extraktion PY - 2024 AN - OPUS4-60284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - EI-GEO (S&T CALL 2017), Environmental impact of geosynthetics in aquatic systems N2 - 2021 marks the 10th anniversary of the first ERA.Net RUS joint call for European-Russian STI cooperation projects. Pooling the resources of more than 20 European and Russian funding agencies, more than 150 projects were funded with an estimated budget of about € 60 million. Being even larger than many thematic ERA.NETs, the ERA.Net RUS Plus has been the biggest and most successful regional ERA.NET so far. Indicating a strong demand for scientific cooperation, the smaller-scale projects funded within the ERA.Net RUS (Plus) calls perfectly complement Russian participation in the EU Framework Programmes. Not least of all, the ERA-Net RUS calls are examples of successful collaboration at a time when cooperation in other fields is complicated by the politically challenging situation. These calls contributed to keeping the communication channels open. Against this background a dedicated event in late 2021 highlighted what has been achieved within the first decade of the initiative. The project EI-GEO coordinated by BAM was selected as best practice project. The presentation displays the main results of the project and discusses the key success factors. T2 - ERA.Net RUS: Celebrating ten years of multilateral European-Russian Research and Innovation cooperation CY - Online meeting DA - 09.12.2021 KW - Geosynthetics KW - Coastal protection KW - European research area PY - 2021 AN - OPUS4-53965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -