TY - CONF A1 - Bresch, Harald T1 - Critical needs and stakeholder networks for engineered particles in air N2 - In the frame of CCQM a new Task Group for particle characterization is being formed. This presentation is a gap analysis and stakeholder mapping for particles in air, from engineered to natural materials. The analysis was requested for the following points: (1) critical literature on stakeholder needs and relevant metrology (2) existing reference materials and relevant interlaboratory comparisons (3) relevant metrology projects (4) critical stakeholders and stakeholder networks and stakeholder surveys T2 - CCQM IAWG/SAWG TG Particle Metrology CY - Online meeting DA - 09.07.2024 KW - CCQM KW - Particle KW - Nano KW - Characterization KW - Aerosol PY - 2024 AN - OPUS4-62067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalinka, Gerhard T1 - Recycling von Faserverbundwerkstoffen N2 - Der Vortrag beschreibt Aktivitäten der BAM zum Recycling von carbonfaser-verstärkten Verbundwerkstoffen. T2 - Fachdialog Recycling von Windenergieanlagen CY - Berlin, Germany DA - 23.09.2024 KW - Polymer Matrix Composite KW - Carbon Fibres KW - Recycling KW - Pyrolysis KW - Recycling by Design PY - 2024 AN - OPUS4-61536 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Advanced lightweight applications – recycling versus reliability and fossil energy footprint N2 - Advanced light weight applications like aircrafts and wind turbine blades are made of fibre reinforced plastics (FRP) with continuous fibre reinforcement and must withstand a high thermo-mechanical cyclic loading. The quality of the fibre matrix interface has a high impact on the fatigue life and was continuously improved over the years since the 50th. The fatigue life of glass fibre reinforced plastics (GFRP) used in aircraft industry is 10 to 100 times higher compared to glass fibre non crimp fabrics used for wind turbine blades. To assure a constant and reliable high quality and strength of reinforcement fibres, synthetic fibre production is state of the art (CF, GF). There is a need for recycling GFRP and CFRP waste due to the upcoming use. Pyrolysis and solvolysis are more expensive than the mechanical route however enable a more sustainable recycling. Natural fibres and recycled synthetic fibres have a high scatter in quality and strength. Hence it is a challenge to optimize the production / recycling processes to get a reliable quality for any demanding (second life) application. Chemical routes for using renewables resources and recycling, is going to be a good approach especially for polymer-matrix systems to get 100% quality (back) compared to the state of the art. Finally, a proper design, life-time extension and repair is preferable to recycling to keep the carbon footprint as low as possible. T2 - 27. INTERNATIONALES DRESDNER LEICHTBAUSYMPOSIUM CY - Dresden, Germany DA - 13.06.2024 KW - Polymer Matrix Composites KW - Carbon Fibre KW - Recycling KW - Circular Economy PY - 2024 UR - https://leichtbausymposium.de/deu/ AN - OPUS4-60683 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - Anwendungen von maschinellem Lernen und KI an der BAM N2 - Im Austausch mit den anderen Bundesoberbehörden wurden die KI-Ansätze der verschiedenen Bundesoberbehörden zu spezifischen Themen der Nanowissenschaften präsentiert. Der Vortrag der BAM fokusiert sich auf die Themen "Self driving lab", semantische Segmentierung und Auswertung von elektronenmikroskopischen Bildern sowie die Generierung von ausführbaren Machineninstruktionen aus natürlicher Sprache. Abschließend wird der neue BAM DataStore vorgestellt. T2 - Nano-Behördenklausur 2024 CY - Berlin, Germany DA - 03.07.02024 KW - Nano KW - Bundesoberbehörden KW - Künstliche Intelligenz KW - Neuronale Netzwerke KW - Elektronisches Laborbuch PY - 2024 AN - OPUS4-61819 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Anja T1 - Reducing Escherichia coli adhesion to PET by modulating spatial periods of laser-induced surface nanoripples N2 - Using nanofiber-like cell appendages, secreted proteins and sugars, bacteria can establish initial surface contact followed by irreversible adhesion and the formation of multicellular biofilms. Here, the stabilizing extracellular biofilm matrix together with physiological changes on the single cell level leads to an increased resilience towards harsh environmental conditions, antimicrobials, the host immune response and established cleaning procedures. Persistent microbial adhesion on e.g., medical implants, in water supply networks or food-processing industry is often associated with chronic inflammation, nosocomial and foodborne infections, enhanced biofouling and product contamination. To prevent persistent microbial colonization, antibacterial surface strategies often target the initial steps of biofilm formation and impede adhesion of single cells before a mature biofilm is being formed. While chemical coatings have been widely used, their restricted biocompatibility for eukaryotic cells and attenuated antibacterial-effects due to compound release limit their areas of application and alternative strategies focus on modified surfaces topographies to impede bacterial adhesion. In this work, we used ns-UV laser treatment (wavelength 248 nm and a pulse duration of 20 ns) to generate laser-induced periodic surface structures (LIPSS) with different submicrometric periods ranging from ~210 to ~610 nm on commercial poly(ethylene terephthalate) (PET) foils. Following structurally and chemically analyses, PET samples were subjected to bacterial colonization studies with Escherichia coli TG1, a bacterial test strain with a strong biofilm formation capacity due to the formation of nanofiber-like cell-appendages (pili). Bacterial adhesion tests revealed that E. coli repellence decisively depends on the spatial periods of the LIPSS with the strongest reduction (~91%) in cell adhesion observed for LIPSS periods of 214 nm. Scanning electron microscopy and additional biofilm studies using a pili-deficient E. coli TG1 strain revealed the importance of extracellular appendages in the bacterial repellence observed here, thus, pointing out new antibiotics-free strategies for antibacterial surfaces by impeding nanofiber-mediated bacterial adhesion. T2 - E-MRS Spring Meeting 2022 CY - Online meeting DA - 30.05.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Bacterial adhesion tests KW - Bacteria repellent surfaces KW - Polymer foils KW - E. coli PY - 2022 AN - OPUS4-54930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Schwibbert, Karin T1 - Laserstrukturierte Oberflächen: Ein Weg zur Kontrolle der Biofilmbildung? N2 - Bakterielle Biofilme stellen in medizinischen und industriellen Bereichen ein ernsthaftes Problem dar. Eine der größten gesellschaftlichen Herausforderungen liegt in der zunehmenden Resistenz von Bakterien gegen Biozide, die bei antimikrobiellen Behandlungen eingesetzt werden, z.B. durch übermäßigen Einsatz in Medizin, Industrie und Landwirtschaft oder durch Reinigung und Desinfektion in Privathaushalten. Daher sind neue effiziente bakterienabweisende Strategien, die den Einsatz von Bioziden vermeiden, dringend erforderlich. Ein vielversprechender Weg zur Erzielung bakterienabweisender Oberflächen liegt in der berührungslosen und aseptischen großflächigen Laserbearbeitung von technischen Oberflächen. Maßgeschneiderte Oberflächentexturen, ermöglicht durch verschiedene Laserbearbeitungsstrategien, die zu topographischen Skalen im Bereich von Nanometern bis Mikrometern führen, können eine Lösung für diese Herausforderung darstellen. In dem Vortrag wird ein Überblick über den aktuellen Stand der Technik bei der subtraktiven Texturierung von Laseroberflächen zur Kontrolle der Biofilmbildung bei verschiedenen Bakterienstämmen und in unterschiedlichen Umgebungen gegeben. Auf der Grundlage spezifischer Eigenschaften von Bakterien und laserbearbeiteten Oberflächen werden die Herausforderungen antimikrobieller Oberflächendesigns erörtert und zukünftige Richtungen aufgezeigt. T2 - GRAVOSeminar, GRAVOmer Kompetenznetzwerk CY - Online meeting DA - 28.02.2024 KW - Laser-Materialbearbeitung KW - Ultrakurzpuls-Laser KW - Biofilme KW - Antibakterielle Oberflächen KW - Oberflächenfunktionalisierung PY - 2024 UR - https://gravomer.de/veranstaltungen-anzeigen/laserstrukturierte-oberflaechen-ein-weg-zur-kontrolle-der-biofilmbildung AN - OPUS4-59594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Monitoringprogramm zur Verwertung von Bodenmaterial gemäß §§ 6-8 Novelle BBodSchV N2 - Dem Fachbeirat Bodenuntersuchungen des BMBF/UBA wurden die abschließenden Ergebnisse zum UFOPLAN-Forschungsvorhaben „Monitoring zur Verwertung von Bodenmaterial“ vorgestellt. Die potentielle Auswirkung der neuen Regularien in der geplanten Novelle der BBodSchV (4. Referentenentwurf der Mantelverordnung) auf die Erweiterung der Verwertungsmöglichkeiten von Bodenmaterialien wurden aufgezeigt. T2 - 41. Sitzung des Fachbeirates für Bodenuntersuchungen CY - Online meeting DA - 16.06.2020 KW - Bodenmaterial KW - Verwertung KW - Elutionsverhalten KW - BBodSchV PY - 2020 AN - OPUS4-50932 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - Materialität von Musikhandschriften N2 - Die Bezeichnung „Tinte auf Papier“ bietet einen guten Einstieg in die Beschreibung der Materialität von Musikhandschriften; so haben sich zahlreiche Manuskripte erhalten, die mit Eisengallustinte auf Hadernpapier verfasst wurden. Das Papier besteht aus Fasern meist pflanzlicher Herkunft und wird durch Entwässerung einer Fasersuspension auf einem Sieb gebildet. Der Abdruck des Schöpfsiebes (die Papierstruktur) und ein vorhandenes Wasserzeichen bieten Anhaltspunkte für Provenienz und Datierung; daneben erlaubt die Analyse der Fasern, der Füllstoffe und der Leimung eine weitere Charakterisierung des Schriftträgers. Spätestens seit dem Mittelalter sind es Eisengallustinten, die das schwarze bis bräunliche Erscheinungsbild vieler Manuskripte auf Papier hervorrufen. Daneben lassen sich auch schwarze Rußtuschen oder farbige Auszeichnungstuschen nachweisen. Eisengallustinten werden durch Mischung einer eisenhaltigen Komponente mit Gerbstoffen hergestellt. Eisensulfat ist die am häufigsten genannte Eisen liefernde Zutat, daneben sind aber auch eisenhaltige Minerale, Nägel oder Rost denkbar. Die Gallussäure leitet sich ab aus den Galläpfeln, der krankhaften Veränderung einzelner Planzenteile verschiedener Eichenarten. Diese werden durch die Eiablage von Schlupfwespen hervorgerufen. Wie schon beim Papier ermöglicht der materialanalytische Nachweis charakteristischer Beimischungen oder Verunreinigungen innerhalb der Tinten die Beantwortung kulturhistorischer Fragestellungen – gemeint sind hier die Unterscheidung von Original und Korrektur oder die Sichtbarmachung späterer Ergänzungen. T2 - DFG-Rundgespraech zur Thermographie-Digitalisierung von Wasserzeichen in Musikhandschriften CY - Vienna, Austria DA - 23.10.2023 KW - Thermographie KW - Manuskripte KW - Wasserzeichen KW - Papier PY - 2023 AN - OPUS4-58798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina T1 - Material Studies of Torah Scrolls at the Bundesanstalt für Materialforschung und -Prüfung N2 - In recent years the BAM has been focusing on the characterization of the writing materials of the medieval Torah scrolls. The challenge imposed by the study of this specific type of manuscript led to designing and building dedicated stages to ensure the safety of the scrolls during the analysis. Furthermore, the identification of multiple corrections executed in apparently identical inks required broadening the standard two-step protocol of near infrared reflectography and X-ray fluorescence to include multispectral imaging. This work has prepared the division to participate in the large collaborative project “To roll: Materialisierte Heiligkeit (Materialised Holiness)” based at the Free University, Berlin. The presentation will demonstrate the aims of the studies, preliminary results and the strategies adopted by the division 4.5 of the BAM. T2 - EAJS Congress Branching Out: Diversity of Jewish Studies CY - Frankfurt/Main, Germany DA - 16.07.2023 KW - Ink analyses KW - Manuscript studies KW - Torah Scrolls KW - X-Ray fluorescence KW - Middle Ages PY - 2023 AN - OPUS4-58881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rudy T1 - “From Saul to Paul” - Urban Pests in Cultural Entomology N2 - Harmful insects like clothes moths and termites occurring in the synanthropic environment are considered pests which need to be controlled. However, human culture has also always widely utilized them as central characters in philosophy, in classic and modern world literature, in music and arts, and much more. This article will highlight some recent exploitations of pest insects in Cultural Entomology. It will provide examples of pieces of art and ephemeral displays with clothes moths and termites as protagonists. The insects´ destructive nature on textiles or wood was turned around to a process of creation with aesthetic, philosophical and metaphoric messages, or simply for unique ways of entertainment. References will be provided to milestones of pest insect use in Cultural Entomology. T2 - International Conference on Urban Pests (ICUP) CY - Lund, Schweden DA - 29.06.20925 KW - Termites KW - Cultural Entomology KW - Material pests KW - Performance art KW - Tineola bisselliella PY - 2025 AN - OPUS4-63822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - More than 25 years of ink analysis non-destructive testing of black writing materials N2 - Writing inks can be divided into soluble inks and dispersion inks. Soluble inks are based on plant or insect dyes forming a water solution. In the early European Middle Ages brown plant inks were usually produced from the blackthorn bark and wine. In contrast to these soluble brown inks, one of the oldest black writing materials was produced by mixing soot with gum arabic or animal glue dissolved in a small amount of water. From Pliny’s detailed account of the manufacture of various black carbon inks, we learn that producing pure soot of high quality was not an easy task in Antiquity. Iron gall inks are a borderline case between these two groups. They are produced from four basic ingredients: gallic acid, an iron-containing component, gum arabic as a binding media, and an aqueous medium such as wine, beer, or vinegar. By mixing gallic acid with soluble iron ions, a water-soluble ferrous gallate complex is formed. Exposure to oxygen leads to the formation of insoluble black ferric gallate pigment. Due to the variety of recipes and the natural origin of raw materials, there is a wide range of different components and impurities in writing inks. The Bundesanstalt für Materialforschung und -prüfung (BAM) together with the Centre for the Study of Manuscript Cultures in Hamburg (CSMC) has developed a protocol for ink analysis. It consists of a primary screening to determine the type of the ink and a subsequent in-depth analysis using several spectroscopic techniques (X-ray fluorescence analysis and vibrational spectroscopy). This contribution presents a qualitative and quantitative analysis of historical writing inks to characterize distinguishable inks in manuscripts, to determine the origin of manuscripts, and to assign unknown fragments to time and place. T2 - Beyond the reconstruction of an Urtext: “About the history of the early Qurʾānic text with regard to digital research tools” CY - Hesse, Germany DA - 07.07.2025 KW - Archaeometry KW - Non-destructive testing KW - Material analysis KW - Cultural heritage PY - 2025 AN - OPUS4-63906 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Poelke, Birte A1 - Klein, Luise A1 - Rohloff, Alexander A1 - Hoffmann, Holger T1 - Initial VOC Emissions from Consumer Products Determined in Micro-Scale Test Chambers: Results of a Round Robin Test N2 - Emissions of volatile organic compounds (VOCs) from consumer products may have a negative impact on indoor air quality, potentially also affecting human wellbeing. Since consumers may be exposed to these VOCs immediately after e.g. unwrapping of newly purchased products, reliable analytical methods are needed to determine air concentration profiles in the early phase of VOC emissions. Concerning typical sample sizes of consumer products, micro-scale test chambers (μ-chambers) were considered suitable for this purpose. In addition, compared to medium- or large-scale test chambers, μ-chambers require lower initial investment and operational costs, and offer options for emissions screenings where higher sample throughput is essential. For these reasons, a μ-chamber-based method to determine initial concentrations of VOCs emitting within the first hours of simulated product use was developed. The chamber air was frequently sampled on desorption tubes loaded with Tenax® TA, followed by quantification of emitted VOCs via thermal desorption gas chromatography mass spectrometry (TD-GC-MS). The method was assessed in a round robin test involving eight participating laboratories from 2 countries. Pieces of a rain poncho (sample area A: 2.01·10-4 m2) emitting cyclohexanone, phenol, 2-ethylhexanol, naphthalene and isophorone in significant concentrations were distributed as sample material. Each laboratory conducted triplicate emission tests over a period of 48 h in μ-chambers with volumes of 44 or 114 mL. The loading factors L of 4.57 m2·m-3 (44 mL) or 1.76 m2·m-3 (114 mL) and air flow rates of 24 mL·min-1 resulted in area-specific air flow rates q of 7.17 m3·m-2·h-1 in both chamber types. The temperature was set to 23°C and, if possible, relative humidity was set to approx. 50%. The chamber air was sampled after 0.5, 1, 2, 4, 24 and 48 hours. In addition, to assess the analytical performance, each participating laboratory received two analyte-spiked Tenax® TA-loaded desorption tubes for quality control (QC). Very low relative standard deviations (11–17%) were obtained for the QC test. The results of the emissions tests in the early phase (0.5–4 h) were also adequate, with acceptable z scores (|z|≤2.00) received by six to seven participating laboratories. All eight laboratories obtained acceptable z scores after the longer sampling periods (24 and 48 h). Hence, the inter-laboratory comparability of the results obtained with the developed μ-chamber method was successfully confirmed. T2 - Healthy Buildings Europe 2025 CY - Reykjavik, Iceland DA - 08.06.2025 KW - VOC Emissions KW - Consumer Product KW - Test Chamber KW - Round Robin Test PY - 2025 AN - OPUS4-63706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimmer, Christoph T1 - Development, application and measurement uncertainty of emission reference materials N2 - Volatile organic compounds (VOCs) emitted by furniture and building materials can cause health issues. For an improvement of indoor air quality low emitting materials should be used. Quality assurance and –control (QA/QC) measures require an emission reference material (ERM) with a predictable emission rate of VOCs. The idea is to use porous materials as ERM, which store the VOCs inside their pores and emit them constantly. T2 - Webinar Metrology for Indoor Air Quality Reference materials for QA/QC of the emission test chamber procedure CY - Online meeting DA - 11.04.2024 KW - Emission reference materials KW - Indoor air quality KW - Materials emissions test KW - VOC PY - 2024 AN - OPUS4-59963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias T1 - Metrological sound reference products for quality assurance and quality control measures in material emissions testing N2 - In industrialised countries more than 80% of the time is spent indoors. Products, such as building materials and furniture, emit volatile organic compounds (VOCs), which are therefore ubiquitous in indoor air. Different VOC combinations may, under certain environmental and occupational conditions, result in reported sensory irritation and health complaints. A healthy indoor environment can be achieved by controlling the sources and by eliminating or limiting the release of harmful substances into the air. One way is to use materials proven to be low emitting. Meanwhile, a worldwide network of professional commercial and non-commercial laboratories performing emission tests for the evaluation of products for interior use has been established. Therefore, comparability and metrological traceability of test results must be ensured. A laboratory’s proficiency can be proven by internal and external validation measures that both include the application of suitable reference materials. The emission test chamber procedure according to EN 16516 comprises several steps from sample preparation to sampling of test chamber air and chromatographic analysis. Quality assurance and quality control (QA/QC) must therefore be ensured. Currently, there is a lack of suitable reference products containing components relevant for the health-related evaluation of building products. The EU-funded EMPIR project 20NRM04 MetrIAQ (Metrology for the determination of emissions of dangerous substances from building materials into indoor air) aims to develop 1) gaseous primary reference materials (gPRM), which are used for the certification of gaseous (certified) reference materials (gCRM) and 2) emission reference materials (ERM). Most commercial gas standards of indoor-relevant compounds are not certified due to the lack of primary reference materials to which the project aims to contribute. The gPRM under development is a gas-phase standard containing trace levels of VOCs in nitrogen or air from the check standard according to EN 16516 (n-hexane, methyl isobutyl ketone, toluene, butyl acetate, cyclohexanone, o-xylene, phenol, 1,3,5-trimethylbenzene) with a target uncertainty of 5 %. The gPRM can be sampled into sorbent tubes to obtain transfer standards in the form of gCRM. The well characterised ERM represents a sample of a test specimen, e.g. building material, that is loaded into the emission test chamber for a period of several days and is used to evaluate the whole emission test chamber procedure. It shall have a reproducible and temporally constant compound release of less than 10 % variability over 14 days. Different approaches for retarded VOC release, such as the encapsulation of pure compounds and the impregnation of porous materials, are being tested to reach this aim. Furthermore, the design of the ERM is accompanied by the development of a numerical model for the prediction of the emissions for each of the target VOCs. The current progress of the work on both materials will be presented. T2 - CIM 2023 - 21st International Metrology Congress CY - Lyon, France DA - 07.03.2023 KW - Indoor air quality KW - VOC KW - Materials emissions testing KW - Emission reference material KW - Quality assurance/quality control PY - 2023 AN - OPUS4-57142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimmer, Christoph T1 - Preparation of novel emission reference materials: μ-capsules & impregnated porous materials N2 - Volatile organic compounds (VOCs) emitted by furniture and building materials can cause health issues. For an improvement of indoor air quality low emitting materials should be used. Quality assurance and –control (QA/QC) measures require an emission reference material (ERM) with a predictable emission rate of VOCs. The idea is to use porous materials as ERM, which store the VOCs inside their pores and emit them constantly. T2 - WORKSHOP: METROLOGY FOR INDOOR AIR QUALITY CY - Mol, Belgium DA - 18.10.2023 KW - Emission reference materials KW - Indoor air quality KW - Materials emissions test KW - VOC PY - 2023 AN - OPUS4-59961 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias T1 - Emission reference materials for indoor air measurements N2 - In industrialised countries more than 80% of the time is spent indoors. Products, such as building materials and furniture, emit volatile organic compounds (VOCs), which are therefore ubiquitous in indoor air. VOC in combination may, under certain environmental and occupational conditions, result in reported sensory irritation and health complaints. Emission concentrations can become further elevated in new or refurbished buildings where the rate of air exchange with fresh ambient air may be limited due to improved energy saving aspects. A healthy indoor environment can be achieved by controlling the sources and by eliminating or limiting the release of harmful substances into the air. One way is to use (building) materials proved to be low emitting. Meanwhile, a worldwide network of professional commercial and non-commercial laboratories performing emission tests for the evaluation of products for interior use has been established. Therefore, comparability of test results must be ensured. A laboratory’s proficiency can be proven by internal and external validation measures that both include the application of suitable emission reference materials (ERM). For the emission test chamber procedure according to EN 16516, no artificial ERM is commercially available. The EU-funded EMPIR project MetrIAQ aims to fill this gap by developing new and improved ERMs. The goal is to obtain a material with a reproducible and temporally constant compound release (less than 10 % variability over 14 days). Two approaches were tested: the impregnation of porous materials with VOC, and the encapsulation of VOC in polymer microcapsules. Impregnation is performed with help of an autoclave and supercritical CO2. The encapsulation is done by interfacial polymerisation on VOC droplets. For both approaches, synthesis and/or material parameters were varied to obtain an optimal ERM. Findings about the optimisation of ERM generation, as well as performance of the best emission reference materials, will be presented. T2 - GAS Analysis 2024 CY - Paris, France DA - 30.01.2024 KW - Emission reference materials KW - Materials emissions test KW - VOC KW - Indoor air quality PY - 2024 AN - OPUS4-59506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Current status of monitoring of PFAS release from industrial facilities N2 - Increasing studies report per- and polyfluoroalkyl substances (PFAS) in the ambient air and emissions from diverse industrial sources. Therefore, a comprehensive framework for characterizing PFAS emissions by identifying source-specific chemical fingerprints, evaluating emission pathways and assessing the impact of remediation technologies is needed. Depending on the type of PFAS, dedicated sampling and analytical procedures are required. Here, also the detection of possible PFAS transformation products, so-called products of incomplete combustion (PICs) are more mobile or toxic, is also of great interest to evaluate these technologies in terms of mineralisation potential and fluorine mass balance. T2 - PFAS study and technical exchange tour of MEE-FECO in Germany CY - Online meeting DA - 12.09.2025 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration PY - 2025 AN - OPUS4-64081 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oberbeckmann, Sonja T1 - Microplastic-microbiome interactions in aquatic ecosystems: a complex story N2 - As pervasive and persistent pollutants, microplastics exist alongside diverse microbial communities in nature. These hardy substrates accumulate rich polymeric matrices from their surroundings that in turn offer nutrition and protection to diverse communities and their theatre of activity, representing a new ecological niche. With our work, we aim to establish a holistic understanding of the interactions between microplastics and microorganisms within aquatic systems, and how these interactions shape their surrounding environment. In our research, we combine field sampling with in situ experiments, and apply high-throughput sequencing technologies to 16S genes and whole bacterial genomes. We demonstrate through our studies that biofilm communities exhibit no specificity to plastic polymer type but appear rather to be opportunistic colonizers more strongly shaped by spatial and temporal factors. While the polymer surface does not appear to elicit a selective effect on associated biofilms, our studies show that microplastics might shape communities in a different way. Based on our detection of carotenoid synthesis pathways and photosynthetic gene clusters among plastic biofilms, we postulate this new niche to shape a specific functional toolkit, adaptive among its members as a product of prolonged exposure to UV radiation at the sea’s surface. To fully assess the interactions between microplastics and microorganisms, however, one cannot consider plastics singularly but as a component within a more complex and interconnected system. It is known, for instance, that plastics can sorb significant concentrations of polycyclic aromatic hydrocarbons (PAH) in the environment. We show, in our work, that the PAH sorption patterns of microplastics correlate significantly with the structure of associated biofilm communities. Elevated concentrations of specific PAHs on microplastics coincided with the enrichment of selected taxa reportedly capable of hydrocarbon utilisation as well as a reduced diversity among associated biofilm communities. Here, we present a synthesis of our collective research on microplastic biofilms in the aquatic environment, the factors that shape them, and their interactions with nature. To fully comprehend how microplastics impact ecosystems, the entire substrate must be considered, including all chemicals integrated into the polymeric matrix as well as associated biofilms. T2 - SETAC Europe 35th Annual Meeting CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Biofilms KW - PAH PY - 2025 AN - OPUS4-63154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - A brief survey on open questions about laser-induced periodic surface structures N2 - The processing of laser-induced periodic surface structures (LIPSS) represents a simple and robust way for the nanostructuring of solids that allows creating a wide range of surface functionalities featuring applications in optics, tribology, medicine, energy technologies, etc. While the currently available laser and scanner technology already allows surface processing rates at the m2/min level, industrial applications of LIPSS are sometimes hampered by the complex interplay between the nanoscale surface topography and the specific surface chemistry. This typically manifests in difficulties to control the processing of LIPSS and in limitations to ensure the long-term stability of the created surface functions. This presentation aims to identify some unsolved scientific problems related to LIPSS, discusses the pending technological limitations, and sketches the current state of theoretical modelling. Hereby, it is intended to stimulate further research and developments in the field of LIPSS for overcoming these limitations and for supporting the transfer of the LIPSS technology into industry. T2 - E-MRS Spring Meeting 2022 CY - Online meeting DA - 30.05.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Surface functionalization KW - Industrial applications KW - Biofilm growth PY - 2022 AN - OPUS4-54929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life on the rocks and other hard surfaces N2 - After their discovery on rock surfaces in cold and hot deserts, a polyphyletic group of ascomycetous black fungi was found to dominate a range of hostile environments – natural and man-made, from salterns to dishwashers, roofs and solar panels. Together with bacteria and algae they may establish subaerial biofilms and cause weathering of the surfaces they grow on. Their impressive survival abilities as well as their constitutive protective pigmentation and cluster-like microcolony organisation are similar in environmental isolates as well as in heat-tolerant opportunistic pathogens of animals and humans. We selected the rock-inhabiting fungus Knufia petricola (class Eurotiomycetes, order Chaetothyriales) that exhibits all the characteristics of microcolonial black fungi such as yeast-like cell growth, absence of reproductive structures and constitutive dihydroxynaphthalene (DHN) melanogenesis (Nai et al. 2013, Fungal Genet Biol). We developed protocols to efficiently generate and transform protoplasts resulting in stable homokaryotic transformants by targeting genes involved in pigment synthesis. The differences between the wild-type fungus and its melanin-deficient mutants were tested in geomicrobiological experiments and measured are now discussed in detail, with special accent on the possible effects of the mutation on EPS and other exuded substances. T2 - Departmental colloquium of the Tuscia University CY - Viterbo, Italy DA - 14.02.2020 KW - Ascomycetes KW - Fungal biofilms KW - Material surface colonisation KW - Genetics KW - Genomics KW - Extremophilic fungi PY - 2020 AN - OPUS4-50643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -