TY - CONF A1 - Wilke, Olaf T1 - Contaminants of Emerging Concern from Materials and Products: Measurement and Evaluation N2 - Test chamber measurements are an important tool to improve indoor air quality and occupational safety. Test chamber measurements are possible for a wide range of materials, products and technologies. Determination of concerning contaminants is important to ensure good indoor air quality. The detection of concerning contaminants depends on the approriate sampling and analysis. T2 - Webinar BAM-University of Birmingham CY - Online meeting DA - 24.02.2021 KW - Emerging Contaminants KW - Emission Test Chamber KW - Thermal Extraction KW - Thermal Desorption PY - 2021 AN - OPUS4-52262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Harmonised test standard EN 16516 - common approach for all building products for interiors N2 - The presentation gives general information about the European Standard EN 16516 “Construction products – Assessment of release of dangerous substances – Determination of emissions into indoor air”. This test standard was developed based on the mandate M/366 of the European commission and is a horizontal reference method for the determination of volatile organic compounds (VOC) from different classes of construction (building) products. Specific test conditions are to be selected by the product TCs (technical committees) in a way that a product is tested under its intended condition of use. The test is based on the use of emission test chambers which are operated at constant air change rate and climate (23°C, 50 % r.h.) over 28 days. The standard defines the conditions and requirements for the measurement including loading factor, air change rate, sampling, analysis and calculation of emission rates of the substances. A 30 m³ reference room is described which is used to calculate air concentrations from the determined emission rates. The standard EN 16516 enables the evaluation of construction products regarding their emissions into indoor air under defined and comparable conditions. The evaluation includes the determination of identified target compounds, non-identified target compounds, volatile carcinogenic compounds and the sum values TVOC, TSVOC and R. T2 - UBA Conference - Limiting health impacts of construction products regarding VOC CY - Online meeting DA - 20.04.2021 KW - Building products KW - EN 16516 KW - Emisson testing KW - Construction products PY - 2021 AN - OPUS4-58079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wen, Keqing T1 - In situ analysis of biofilm formation under different flow regimes with the help of a microfluidic platform N2 - Bacteria often live in habitats characterized by fluid flow, which is ubiquitous in a diverse range of environments such as surface waters, wastewater treatment facilities, pipelines, and medical implants. Bacterial adhesion on surfaces may lead to biocorrosion and biodegradation. In comparison to traditional static and macro flow chamber assays for biofilm formation studies, microfluidic chips allow in situ monitoring of biofilm formation and biofilm related gene expression under various flow regimes. We developed a complete microfluidic platform to investigate biofilms under precisely controlled flow conditions. This platform central unit is a single-inlet microfluidic flow cell with a 5 mm wide chamber tested and analyzed by imaging tracking velocimetry (PIV) to achieve ultra-homogenous flow in the central area of the chamber. Additionally, dedicated microstructures were introduced to the chamber’s center to favor and localize bacterial adhesion and biofilm formation pattern. The flows and vortices induced by the structure were analyzed by computational fluid dynamics (CFD) and related to shape and dimension of the biofilm formed by Escherichia coli TG1. The major proteinaceous component of E. coli biofilms are extracellular amyloid fibers (curli) consisting of major (CsgA) and minor (CsgB) subunits. We used the promotor probe plasmid pRU1701 to monitor csgB-promotor activity under different flow regimes in complex and minimal medium. For comparison, csgB promotor activity in a batch liquid culture and curli production on LB and M9 agar plates were assessed. The microfluidic platform represents a powerful and versatile tool for studying biofilm in flow. The setup shows great potential for the yet not too much explored in flow monitoring of biofilm formation and related gene expression under hydrodynamic stresses. T2 - International Biodeterioration and Biodegradation Symposium (IBBS) 19 CY - Berlin, Germany DA - 09.09.2024 KW - Microfluidics KW - Biofilm KW - Escherichia coli KW - Curli PY - 2024 AN - OPUS4-61911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Einführung in die Mantelverordnung - Stand der Bundes-Bodenschutz- und Altlastenverordnung N2 - Einführung in die Mantelverordnung Stand der Bundes-Bodenschutz- und Altlastenverordnung, aktuelles zum Aufbau der MVO und zum Stand Anfang 2023 T2 - X. Baustoffseminar - Aktuelles zu Gesteinskörnungen CY - Bad Berka, Germany DA - 17.01.2023 KW - Mantelverordnung KW - Gesteinskörnungen KW - Wiederverwertung PY - 2023 AN - OPUS4-57798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Entwicklungen im Gipsrecycling N2 - Gips gehört zu den nachgefragtesten Baustoffen und entsprechend steigt der Gipsverbrauch weltweit schon seit Jahrzehnten an. In Deutschland wird der Gipsbedarf seit vielen Jahren zu einem guten Teil durch REA-Gips, einem Nebenprodukt aus der Abgasreinigung von Kohlekraftwerken, gedeckt. Die weitere Gipsversorgung erfolgt größtenteils durch die Nutzung natürlicher Gipsvorkommen. Ein geringer, aber steigender Anteil an RC-Gips aus dem Baustoffrecycling und die Nutzung synthetischer Gipse aus Nebenprodukten anderer Industriezweige sind ebenfalls zu verzeichnen. Aufgrund der nationalen Klimaschutzziele und der damit verbundenen Abschaltung von Kohlekraftwerken wird das REA-Gipsangebot in den nächsten Jahren jedoch weiter deutlich zurückgehen, so dass andere Gipsquellen erschlossen werden müssen. Abhängig von der Lebensdauer der verwendeten Gipsprodukte im Bausektor ist infolge des in den vergangenen Jahren erfolgten Anstiegs des Gipsverbrauchs auch mit einer Zunahme von Gipsresten in Bau- und Abbruchabfällen zu rechnen. Im Hinblick auf eine bevorstehende Verknappung von Gips wird die Rückgewinnung dieser Gipse aus Bau- und Abbruchabfällen immer wichtiger. Das Recycling von Gipskartonplatten ist mittlerweile eine etablierte Technik und wird bereits seit einigen Jahren in industriellem Maßstab durchgeführt. Außerdem werden neue Verfahren zur Wiederverwertung weiterer Gipsprodukte aus Rück- und Umbaumaßnahmen untersucht. Von besonderem Interesse sind verschiedene Arten von Gipsplatten, da sie gut für selektiven Rückbau geeignet sind. Daher können sie vergleichsweise frei von Verunreinigungen oder Störstoffen zurückgewonnen werden, was für das Gipsrecycling besonders wichtig ist. In dem vom Bundesministerium für Bildung und Forschung geförderten Forschungsprojekt "GipsRec 2.0" werden technische, wirtschaftliche und ökologische Aspekte des Recyclings von Gipsfaserplatten sowie von verschiedenen Synthesegipsen untersucht und bewertet. Die Aufbereitung von Gipsfaserplatten erfolgte im halbtechnischen Maßstab, an verschiedenen potentiellen Ausgangsstoffen für synthetische Gipse wurden Laborversuche durchgeführt. Erfolgversprechende Verfahrenswege werden ökobilanziell bewertet. Ziel dieser Arbeiten ist die Erschließung der Sekundärrohstoffpotenziale von weiteren Quellen für die RC-Gipsproduktion um mit einer Steigerung des Gipsrecyclings die in naher Zukunft durch die Reduktion der REA-Gips-Bereitstellung entstehende Lücke in der Rohstoffversorgung zu verringern. T2 - 21. ibausil 2023 CY - Weimar, Germany DA - 13.09.2023 KW - Baustoffrecycling KW - Sekundärgipse KW - Ökobilanz PY - 2023 AN - OPUS4-60314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Neue Ansätze beim Gipsrecycling N2 - Gypsum is widely used in the construction sector, and its worldwide consumption has been increasing now for several decades. Currently, the gypsum demand is met up to 60% by FGD gypsum (a by-product from coal-fired power plants) in Germany. The natural gypsum deposits cover the remaining gypsum demand. Due to national climate protection goals and the related shutdown of coal-fired power plants, the FGD gypsum supply will decrease significantly in the coming years and, therefore, other gypsum sources must be found. Depending on the lifetime of the used gypsum products in the construction sector, an increase of gypsum in construction and demolition waste is to be expected. With regard to an upcoming shortage of gypsum, several approaches are being tested to recover gypsum from construction and demolition waste. Gypsum plasterboard recycling is already implemented on an industrial scale. Furthermore, new processes to recycle different types of gypsum products from construction and demolition waste are being examined. Of particular interest are different types of gypsum boards because they are well suited for selective dismantling. Therefore, they can be recovered comparatively free of impurities which is most important for the gypsum recycling. In the research project “GipsRec 2.0”, funded by the Federal Ministry of Education and Research, recycling methods for gypsum fiberboards are being investigated. Additionally, the suitability of different types of synthetic gypsum as substitutes for FGD gypsum is being considered. Currently, the quantities of recycled gypsum are not sufficient with regard to the reduction of FGD gypsum. An increase of gypsum recycling should be achieved to narrow the future gypsum gap that will occur in the near future. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 13.09.2021 KW - Gipsabfälle KW - Gipsrecycling KW - Nachhaltigkeit PY - 2021 AN - OPUS4-53682 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Baustoffrecycling: Kreislaufwirtschaft und Umweltschutz N2 - Aktuelle Zahlen zum Baustoffrecycling Zielkonflikte im Kontext von Abfallwirtschaft, Boden- und Grundwasserschutz sowie rechtlichen Vorgabe mit den Beispielen rezyklierte Gesteinskörnungen und RC-Gips. T2 - IX. Baustoffseminar CY - Weimar, Germany DA - 11.03.2020 KW - Kreislaufwirtschaft KW - Baustoffrecycling KW - Ressourcenschonung PY - 2020 AN - OPUS4-51436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - New sources for secondary gypsum N2 - In order to protect natural gypsum deposits and to compensate for the decreasing amount of Flue Gas Desulfurization (FGD) gypsum it is necessary to develop and explore new sources of gypsum. For this purpose, the potentials of different gypsum wastes are investigated in the study “GipsRec 2.0”, funded by the Federal Ministry of Education and Research (Germany). On the one hand, the project worked on a new processing technology for gypsum fiberboards (GFB). While the recycling of gypsum plasterboards has already been carried out on an industrial scale for several years, the recycling of gypsum fiberboards (GFB) has proven to be challenging. Gypsum fiberboards from demolition sites and offcuts from GFB production were used for these investigations. The tests were conducted on a technical scale. Furthermore, various synthetic gypsums are being investigated with regard to their suitability for gypsum production. The analyses are carried out on production residues. In this project, a promising process for gypsum fiberboard recycling could be developed, as well as other waste gypsums are investigated and evaluated with regard to their potential as secondary raw material. In addition, selected process routes are assessed for their environmental impact using a life cycle assessment (LCA) approach. T2 - RILEM - V International Conference Progress of Recycling in the Built Environment CY - Weimar, Germany DA - 10.10.2023 KW - Gypsum recycling KW - Gypsum fiberboards and synthetic gypsum KW - Environmental evaluation PY - 2023 AN - OPUS4-60316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Biorezeptivität und Optimierung von Lehmbaustoffen - Forschung an der BAM N2 - Der Vortrag fasst die Forschungsaktivitäten der BAM in den Themengebieten Biorezeptivität von Beton und Optimierung von Lehmbaustoffen zusammen. Er diente als Kurzpräsentation für eine anschließende Podiumsdiskussion. T2 - Transformationsdialog "Material als Motor" CY - Berlin, Germany DA - 10.10.2024 KW - Biorezeptivität KW - Beton KW - Lehmbaustoffe PY - 2024 AN - OPUS4-62220 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Living Concrete Walls: Engineering Bioreceptivity and Biofilms N2 - Building envelopes are a natural habitat of subaerial biofilms and can be more or less prone to be colonized (i.e. to be bioreceptive). Focusing on the added value of biofilms on manmade substrates represents new aesthetic frontiers and reduces the use of biocides. Moreover, the metabolic processes of photosynthetic biofilms can positively influence human health and life quality in densely populated cities by converting or absorbing pollutants. In the presented research the bioreceptivity of concrete claddings for building facades is engineered to sustain either natural or artificial establishment of microalgae-dominated biofilms. To be able to differentiate between the intrinsic material properties and the climatic boundary conditions, the experimental design in the first step comprised different analyses with model mono- and multi-species biofilms in sterile conditions and a high control of the environmental parameters. Growth and vitality of the algal component of the biofilms has been assessed with Pulse-amplitude modulation (PAM) fluorometry. T2 - 78th RILEM Annual Week & RILEM International Conference on Sustainable Materials & Structures: Meeting the major challenges of the 21st century - SMS 2024 CY - Toulouse, France DA - 25.08.2024 KW - Bioreceptivity KW - Biofilm KW - Weathering KW - Concrete KW - PAM fluorometry KW - Carbonation PY - 2024 AN - OPUS4-62224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Gebäudebegrünung mit Biofilmen: Herausforderungen und Chancen N2 - Der Vortrag stellt die Ergebnisse der Forschungsarbeiten zur Biorezeptivität von Betonfassaden sowie der gezielten Applikation von Algen dominierten Biofilmen auf Betonfassaden vor. Insbesondere werden die Anforderungen an eine repräsentative Prüfmethode erläutert. T2 - BuGG-Tag der Forschung und Lehre Gebäudegrün 2024 CY - Leipzig, Germany DA - 26.09.2024 KW - Begrünung KW - Biorezeptivität KW - Beton KW - Biofilm PY - 2024 AN - OPUS4-62221 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Biofilme auf Gebäuden - Biorezeptivität statt Biofilme N2 - Der Vortrag erläutert das Konzept der Gebäudebegrünung mit Biofilmen. Beton wird dabei als künstliches Gestein betrachtet, dessen Besiedelbarkeit durch Mikroorganismen gezielt verbessert werden soll. Ein dreistufiges Testsystem – Laborversuche, simulierte Bewitterung und Freilandtests – analysiert, wie physikalische und chemische Substrateigenschaften das Wachstum beeinflussen. Ein definierter Algen‑Pilz‑Modellbiofilm dient zur reproduzierbaren Bewertung der Besiedlung, erfasst über PAM‑Fluorometrie. Die Ergebnisse zeigen, dass Rauheit, Textur und Porosität entscheidend für Anhaftung, Feuchteretention und Biofilmwachstum sind. Zudem wird deutlich, dass die Organismen hohe Stresstoleranz benötigen, um variierende Umweltbedingungen an realen Fassaden zu überstehen. Insgesamt belegt das Projekt das Potenzial biorezeptiver Betone als low‑tech‑Fassadenbegrünung mit ökologischem Mehrwert. T2 - Workshop Ökologische Campusentwicklung: Wasser und Vegetationsmanagement in Helmholtz-Zentren CY - Potsdam, Germany DA - 03.04.2025 KW - Biofilm KW - Fassade KW - Biorezeptivität KW - Low-tech Begrünung KW - Modellbiofilm PY - 2025 AN - OPUS4-65448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Bioreceptive Building Facades: Codesigning with nature N2 - Building envelopes represent a key interface between solid substrates, the biosphere, and the atmosphere, and consequently serve as natural habitats for subaerial biofilms. This study investigates strategies to enhance the bioreceptivity of concrete cladding to support microalgae‑rich biofilms as a sustainable alternative to biocide‑dependent facade systems. Using a controlled dual‑species biofilm model and assessing algal vitality via PAM fluorometry, we examined how concrete composition and surface properties influence colonization dynamics. The results demonstrate that substrate pH and carbonation state are primary determinants of both biofilm establishment and organismal vitality, whereas nutrient supplementation exerts comparatively minor effects. Adhesion assays indicate that moderate mechanical stress can increase biofilm robustness, and laboratory rain simulations show that surface texture and near‑surface porosity promote water retention and enhance biofilm attachment. A synergistic interaction between the algal and fungal components was observed under specific stress conditions, offering a potential explanation for the reduced performance of biofilms when transitioning from ideal laboratory settings to outdoor environments. Overall, the findings highlight that the development of stable, photosynthetically active biofilm facades requires careful optimization of organism growth, physiological performance, and long‑term adhesion to the substrate. T2 - SASBE 2025: Smart and Sustainable Built Environment CY - Lille, France DA - 03.11.2025 KW - Concrete KW - Bioreceptivity KW - Laboratory test KW - Biofilm KW - Fluorometry PY - 2025 AN - OPUS4-65446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Greening Concrete with biofilms: Codesigning with nature N2 - uilding envelopes act as artificial lithic surfaces and natural substrates for subaerial biofilms, whose establishment depends on surface bioreceptivity. This study investigates how concrete cladding can be engineered to support microalgae‑dominated biofilms. A multi‑stage experimental framework—ranging from petri‑dish cultivation and adhesion testing to laboratory weathering simulations and outdoor exposure—was applied. A reproducible dual alga–fungus model biofilm enabled controlled assessment, with algal vitality quantified using PAM fluorometry. Results identify pH and carbonation as primary determinants of successful colonization, while nutrient addition has only minor influence. Adhesion tests show that moderate stress can enhance resilience to hydrodynamic forces. Rain‑simulation experiments highlight the importance of surface texture and near‑surface porosity for water retention, microbial attachment, and sustained growth. A synergistic interaction between algae and fungi under stress conditions may explain the poor outdoor performance of biofilms cultivated under ideal laboratory conditions. Overall, optimizing photosynthetic efficiency, organismal growth, and adhesion strength is essential for developing durable algal biofilm‑based façade systems. T2 - 4th International Conference of Sustainable Building Materials CY - Eindhoven, The Netherlands DA - 10.08.2025 KW - Concrete KW - Bioreceptivity KW - Laboratory test KW - Biofilm KW - Fluorometry PY - 2025 AN - OPUS4-65447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Application of Diffusive Gradients in Thin-films (DGT) and spectroscopic techniques to analyze phosphorus in soils N2 - A wide range of analytical methods are used to estimate the plant-availability of soil phosphorus (P). Previous investigations showed that analytical methods based on the Diffusive Gradients in Thin films (DGT) technique provide a very good correlations to the amount of bioavailable nutrients and pollutants in environmental samples (Davison 2016, Vogel et al. 2017). However, the DGT results do not identify which P compound of the soil has the high bioavailability. But there are various spectroscopic techniques (infrared, Raman, P K-edge and L-edge XANES and P NMR spectroscopy) available to characterize P species in soils. Therefore, spectroscopic investigation of DGT binding layers after deployment allow us to determine the specific compounds. Nutrients such as phosphorus and nitrogen are often, together with other elements, present as molecules in the environment. These ions are detectable and distinguishable by infrared, P K- and L-edge X-ray absorption near-edge structure (XANES) and NMR spectroscopy, respectively. Additionally, microspectroscopic techniques make it also possible to analyze P compounds on the DGT binding layer with a lateral resolution down to 1 μm2. Therefore, species of elements and compounds of e.g. a spatial soil segment (e.g. rhizosphere) can be mapped and analyzed, providing valuable insight to understand the dynamics of nutrients in the environment. T2 - SPP1685 Closing Conference: New Approaches to Ecosystem Nutrition - Phosphorus and Beyond CY - Freiburg, Germany DA - 25.10.2021 KW - Phosphorus KW - Diffusive gradients in thin-films (DGT) KW - Passive sampling PY - 2021 AN - OPUS4-53641 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Ammonium and nitrate in agricultural soils analyzed with the Diffusive Gradients in Thin-films technique N2 - The aim of this study was to investigate the passive sampler method Diffusive Gradients in Thin-films (DGT) for ammonium and nitrate in amended soils. Therefore, we used soils from a pot experiment with maize where nitrogen (N) was supplied as ammonium sulfate nitrate (ASN), without and with a nitrification inhibitor (NI). The additional use of a NI can delay the nitrification in the soil and making the ammonium available for a longer period in the soil solution after its application. Homogenized soil samples were collected directly from each pot after one week of incubation before sowing and after harvesting the maize. Nitrate and ammonium in these soil samples were extracted using DGT devices equipped with a Putolite A520E (for nitrate) and Microlite PrCH (for ammonium) binding layer. Ammonium DGT which determined the mobile and labile ammonium forms based on diffusion and the resupplies from the solid soil phase, only showed a significantly higher amount of extractable ammonium with NI compared to that without NI for some samples. However, significantly lower values were found for nitrate of treatments with NI compared to without NI after harvest. Thus, the lower nitrate amounts for treatments with NI compared to the treatments without NI after harvest indicated the delay of the nitrification process by the NI. Furthermore, we compared also the ammonium and nitrate DGT results to chemical extraction with KCl solutions. The results demonstrated that the trends of DGT results and chemical extraction were complimentary through all the treatments. T2 - International Passive Sampling Workshop (IPSW) 2021 virtual CY - Online meeting DA - 04.11.2021 KW - Phosphorus KW - Diffusive gradients in thin-films (DGT) KW - Ammonium KW - Nitrate PY - 2021 AN - OPUS4-53698 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy as a novel tool for the characterization of per- and polyfluoroalkyl substances (PFAS) in soils and sludges N2 - Per- and polyfluoroalkyl substances (PFAS) have been used extensively in the past because of their inert chemical character and resistance to degradation by environmental influences. Since the beginning of their commercial use, PFAS have been widely exposed to the environment by application of PFAS in consumer products or as foaming agent in firefighting foams, thus several cases of contaminated soils sites have been reported. Since the number of known PFAS already exceeds 4700, their characterization and direct analysis is challenging given the current available techniques. Here, we introduce the novel fluorine (F) K-edge X-ray absorption near-edge structure (XANES) spectroscopy as a tool to analyze PFAS and inorganic fluorine compounds in contaminated soils and sewage sludges. While F K-edge bulk-XANES spectroscopy provide us information on the overall fluorine bonding in a sample micro X-ray fluorescence (XRF) in combination with F K-edge micro-XANES spectroscopy can also detect minor fluorine compounds and PFAS hotspots in investigated soils and sludges. Additionally, we used the combustion ion chromatography (CIC) to analyze the total amount of all PFAS as a sum parameter (extractable organic fluoride: EOF) in soils and sewage sludges. During combustion in the CIC, the PFAS in the sample get destroyed at temperatures of approx. 1000 °C and converted in inorganic fluorides that subsequently gets quantified by ion chromatography. Thus, for the first time we successfully combined F K-edge XANES spectroscopy and CIC as analytical tools to detect and quantify PFAS contaminants in soils and sewage sludges. T2 - SETAC Europe CY - Online meeting DA - 03.05.2021 KW - Sewage sludge KW - Combustion ion chromatography KW - Soil KW - X-ray absorption near-edge structure (XANES) spectroscopy PY - 2021 AN - OPUS4-52563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Analytical Challenges for PFAS in Environmental Samples - Methods, Approaches and Applicability N2 - Per- and polyfluoroalkyl substances (PFAS) are anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms and which include up to 1.7 M compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, because of the continuous contamination through PFAS containing commercial products, effluents and sewage sludge from WWTPs have been shown to be an important source of PFAS discharge into the aquatic environment. In the last few years, legacy PFAS (≥C4) have been found in various environments, including soil, water and wastewater, and their environmental pathways have been partly described. Several long-chain PFAS species, and their respective salts are considered as persistent organic pollutants by the United Nations Stockholm Convention. These pollutants have been linked to altered immune and thyroid function, liver disease, lipid and insulin dysregulation, kidney disease, adverse reproductive and developmental outcomes, and cancer. A significant shift in the chemical industry towards production of short (C4-C7) and ultrashort (C1-C3) alternatives was observed in response to recently intensified regulations and restrictions on the use of long-chain (≥C8) PFAS. PFAS analysis in environmental samples is currently mainly done by liquid chromatography tandem mass spectrometry (LC-MS/MS). This efficient method is conducted in a targeted fashion analyzing a small subset of PFAS. The US EPA method for analysis of PFAS using LC-MS/MS for example currently lists 40 PFAS (≥C4). However, to get a better overview of the amount of “total PFAS,” sum parameter methods like total oxidizable precursor (TOP) assay and methods based on combustion ion chromatography (CIC) are in development. CIC results in data regarding the sum of absorbable organic fluorine (AOF) or extractable organic fluorine (EOF), which can also quantify other organically bound fluorine compounds such as fluorinated pesticides and pharmaceutical. Moreover, non-target and suspect screening mass spectrometry can be used to identify novel emerging PFAS and partly unknown fluorinated compounds in environmental samples. Furthermore, to analyze ultrashort PFAS (C1-C3), supercritical fluid chromatography (SFC), hydrophilic interaction chromatography (HILIC) and gas chromatography-mass spectrometry (GC-MS) are available, but further research is needed to develop reliable and accurate methods to quantify several ultrashort PFAS in environmental samples. Additionally, for research purpose several spectroscopical methods like X-ray photoelectron spectroscopy (XPS), fluorine K-edge X-ray absorption near-edge structure (XANES)spectroscopy, particular induced gamma-ray emission (PIGE) spectroscopy and 19F nuclear magnetic resonance (NMR) spectroscopy are available. T2 - CleanUp 2022 CY - Adelaide, Australia DA - 11.09.2022 KW - PFAS KW - Combustion ion chromatography KW - XANES spectroscopy PY - 2022 AN - OPUS4-55741 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Mechanochemical Remediation of Per- and Polyfluoroalkyl Substanzes (PFAS) in Soils N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of anionic, cationic, or zwitterionic organofluorine surfactants used in the formulations of thousands of products and consumer goods, including aqueous film-forming foams (AFFF) used to suppress aviation fires in training scenarios, non-stick cookware, fast-food wrappers, water-repellent fabrics, medical equipment. Because PFAS have been extensively used in a variety of AFFF products they can be found in soils from industrial and military installations. Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Previously, mechanochemical treatment of polychlorinated organic compounds in soils showed an efficient dechlorination. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GCMS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well es the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - CleanUp 2022 CY - Adelaide, Australia DA - 11.09.2022 KW - PFAS KW - Mechanochemical treatment KW - XANES spectroscopy PY - 2022 AN - OPUS4-55742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - PFAS Sum Parameter and Structural Analysis N2 - Per- and polyfluoroalkyl substances (PFAS) are anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms (see Figure 1) and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, because of the continuous contamination through PFAS containing commercial products, effluents and sewage sludge from WWTPs have been shown to be an important source of PFAS discharge into the aquatic environment. In the last few years, legacy PFAS (≥C4) have been found in various environments, including soil, water and wastewater, and their environmental pathways have been partly described. To get a better overview of the amount of “total PFAS,” sum parameter methods like total oxidizable precursor (TOP) assay and methods based on combustion ion chromatography (CIC) are in development. CIC results in data regarding the sum of absorbable organic fluorine (AOF) or extractable organic fluorine (EOF), which can also quantify other organically bound fluorine compounds such as fluorinated pesticides and pharmaceutical. Additionally, for research purpose several spectroscopical methods like X-ray photoelectron spectroscopy (XPS), fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy, particular induced gamma-ray emission (PIGE) spectroscopy and 19F nuclear magnetic resonance (NMR) spectroscopy are available. Therefore, an overview is given on various analytical techniques for PFAS in environmental samples and their application possibilities discussed for different kind of PFAS compounds T2 - CleanUp 2022 CY - Adelaide, Australia DA - 11.09.2022 KW - PFAS KW - Combustion ion chromatography KW - XANES spectroscopy KW - Soil PY - 2022 AN - OPUS4-55743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -