TY - JOUR A1 - Yalçin, M. A1 - Taşçioğlu, C. A1 - Plarre, Rüdiger A1 - Akçay, Ç. A1 - Busweiler, Sabine T1 - Investigation of natural durability of some native and exotic wood species against Hylotrupes bajulus (Cerambycidae) and Anobium punctatum (Anobiidae) N2 - Aim of study: In this study, natural durability of some domestic and foreign wood species against Hylotrupes bajulus and Anobium punctatum larvae were tested on laboratory scale Area of study: This study was conducted at Department of Forest Products Engineering in Duzce University, Turkey and Federal Institute for Materials Research and Testing (BAM), Germany. Material and Methods: Scotch pine (Pinus sylvestris), fir (Abies nordmanniana), spruce (Picea orientalis), cedar (Cedrus libani), poplar (Populus tremula) and beech (Fagus orientalis) woods were used to test H. bajulus larvae (EN 46-1). Alder (Alnus glutinosa), oak (Quercus cerris), poplar (Populus tremula), beech (Fagus orientalis), maple (Acer carpinifolium), ash (Fraxinus angustifolia), teak (Tectona grandis), ayous (Triplochiton scleroxylon), movingui (Distemonanthus benthamianus), dahoma (Piptadeniastrum africanum), iroko (Chlorophora excelsa), bubinga (Guibourtia tessmannii) and sapele (Entandrophragma cylindiricum) woods were used for A. punctatum larvae (EN 49-1). At the end of the experiment, the mortality rates of the larvae were determined and the size and weights of the surviving larvae were measured. Main results: F. orientalis and C. libani were found to be the most resistant wood species against H. bajulus larvae while A. nordmanniana was the least resistant. All tropical wood species and oak and maple from domestic wood species showed 100% mortality rate therefore found to be the most resistant against A. punctatum larvae. The most vulnerable wood species was found to be alder with a 35% mortality. Research highlights: while F. orientalis, C. libani, and P. tremula were found the most resistance wood species against H. bajulus, P. sylvestris and A. nordmanniana were determined as most vulnerable. All tropical wood species and two domestic species (Q. cerris and A. carpinifolium) showed the highest mortality rate as 100%. The least durable domestic wood was determined as alder. KW - Hylotrupes bajulus, Anobium punctatum, natural durability, tropical wood, native wood. PY - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-446572 SN - 1303-2399 SN - 1309-4181 VL - 18 IS - 1 SP - 83 EP - 91 PB - Kastamonu University CY - Kastamonu AN - OPUS4-44657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Wünsch, Christoph A1 - Simon, Franz-Georg ED - Maletz, Roman ED - Dornack, Christina ED - Ziyang, Lou T1 - The reduction of greenhouse gas emissions through the source-separated collection of household waste in Germany N2 - The production of secondary materials from waste materials requires, in most cases, significantly lower energy amounts than the primary material production of raw materials. Along with lower energy demand, the greenhouse gas emissions produced are also lower. The duty of a modern waste management system should therefore be to collect and sort the waste materials in a way that the highest amounts of single material fractions with the highest qualities can be generated. In this contribution, the greenhouse gas balances of the theoretical treatment of the household waste, if collected as mixed waste in sanitary landfills, in waste incineration plants, or in mechanical-biological treatment plants, are compared to the existing separate waste collection and treatment in Germany in 2014. The results show that the treatment of the mixed collected household waste in sanitary landfills would lead to a significant release of greenhouse gases. The treatment in MBTs with the recovery of valuables and the further disposal of the biologically stabilized fraction on landfills, as well as the treatment of the high calorific fraction (also called refuse derived fuel – RDF) in RDF plants, coal-fired power plants, or cement kilns, would lead to small amounts of avoided greenhouse gas emissions. The thermal treatment in waste incineration plants would lead to moderate amounts of avoided greenhouse gases. Only with the actually practiced separate collection and treatment of household waste were significant amounts of greenhouse gas emissions avoided. In total, this is approximately 5.5 million tons of carbon dioxide equivalents for approximately 45.5 million tons of separate collected and treated household waste in Germany in 2014. KW - Greenhouse gas accounting KW - Greenhouse gas mitigation KW - Household waste KW - Material recycling KW - Separate collection PY - 2018 SN - 978-3-319-69071-1 U6 - https://doi.org/10.1007/698_2017_35 VL - 63 SP - 269 EP - 287 PB - Springer International Publishing CY - Berlin ET - 1 AN - OPUS4-44937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Al-Akel, S. T1 - Aktuelle Diskussionen zur vorläufigen Zulassungsrichtlinie von Bewehrungsgittern für Deponieoberflächenabdichtungen und zu Auftragsnähten in Kunststoffdichtungsbahnen N2 - Die BAM wurde 2009 u. a. mit der Zulassung von Bewehrungsgittern für den Deponiebau beauftragt. Der Stand von Wissenschaft und Technik bot jedoch keine ausreichende Grundlage, die tatsächlich relevanten Widerstände und die mit diesen Widerständen verbundene Wechselwirkung zwischen Gitter und Boden im Hinblick auf eine mindestens 100-jährige Funktionsdauer realistisch beurteilen zu können. Es wurde daher nur eine vorläufige Zulassungsrichtlinie für diese Produkte erarbeitet. In der Zwischenzeit hat sich ein neuer Kenntnisstand ergeben. Vor diesem Hintergrund hat die AG (Arbeitsgruppe) Geogitter des Fachbeirats der BAM am 26.09.2017 getagt. Es sollen die aktuellen Erkenntnisse und Schlussfolgerungen für die Zulassung in Kürze vorgestellt werden. Die entsprechenden Kapitel beruhen dabei auf einem Arbeitspapier von W.W. Müller und dem Autoren, das der Arbeitsgruppe zur Diskussion vorgelegt wurde. Weiterhin soll über Entwicklungen in Zusammenhang mit Kunststoffdichtungsbahnen (KDB) berichtet werden. Die Anforderungen an die Schweißzusätze für das Extrusionsschweißen wurden angepasst. Zudem soll über die aktuelle Diskussion der Schweißbarkeit unterschiedlicher HDPE Materialien informiert werden. Die maßgebliche DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 wird derzeit offenbar so ausgelegt, dass Materialien mit völlig unterschiedlichen Schmelze-Massefließrate miteinander verbunden werden können. Dies steht allerdings im grundlegenden Widerspruch zum Stand der Technik. T2 - 14. Leipziger Deponiefachtagung - Planung, Bau, Betrieb, Stilllegung, Nachsorge und Nachnutzung von Deponien CY - Leipzig, Germany DA - 06.03.2018 KW - Deponietechnik KW - Bewehrungen aus Kunststoff KW - Kunststoffschweißen PY - 2018 SN - 978-3-943443-47-9 VL - 14 SP - 53 EP - 68 AN - OPUS4-44417 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussionen zur vorläufigen Zulassungsrichtlinie von Bewehrungsgittern für Deponieoberflächenabdichtungen und zu Auftragsnähten in Kunststoffdichtungsbahnen N2 - Die BAM wurde 2009 u. a. mit der Zulassung von Bewehrungsgittern für den Deponiebau beauftragt. Der Stand von Wissenschaft und Technik bot jedoch keine ausreichende Grundlage, die tatsächlich relevanten Widerstände und die mit diesen Widerständen verbundene Wechselwirkung zwischen Gitter und Boden im Hinblick auf eine mindestens 100-jährige Funktionsdauer realistisch beurteilen zu können. Es wurde daher nur eine vorläufige Zulassungsrichtlinie für diese Produkte erarbeitet. In der Zwischenzeit hat sich ein neuer Kenntnisstand ergeben. Vor diesem Hintergrund hat die AG (Arbeitsgruppe) Geogitter des Fachbeirats der BAM am 26.09.2017 getagt. Es sollen die aktuellen Erkenntnisse und Schlussfolgerungen für die Zulassung in Kürze vorgestellt werden. Die entsprechenden Kapitel beruhen dabei auf einem Arbeitspapier von W.W. Müller und dem Autoren, das der Arbeitsgruppe zur Diskussion vorgelegt wurde. Weiterhin soll über Entwicklungen in Zusammenhang mit Kunststoffdichtungsbahnen (KDB) berichtet werden. Die Anforderungen an die Schweißzusätze für das Extrusionsschweißen wurden angepasst. Zudem soll über die aktuelle Diskussion der Schweißbarkeit unterschiedlicher HDPE Materialien informiert werden. Die maßgebliche DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 wird derzeit offenbar so ausgelegt, dass Materialien mit völlig unterschiedlichen Schmelze-Massefließrate miteinander verbunden werden können. Dies steht allerdings im grundlegenden Widerspruch zum Stand der Technik. T2 - 14. Leipziger Deponiefachtagung - Planung, Bau, Betrieb, Stilllegung, Nachsorge und Nachnutzung von Deponien CY - Leipzig, Germany DA - 06.03.2018 KW - Bewehrungen aus Kunststoff KW - Kunststoffschweißen KW - Deponietechnik PY - 2018 AN - OPUS4-44418 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wöhlecke, Andreas T1 - Verhindern Geokunststoffe die Entlassung von Deponien aus der Nachsorge? N2 - Derzeit gibt es intensive Diskussionen über die Entlassung von Deponien aus der Nachsorgephase. Die Deponie müsste dafür nach der Deponieverordnung (DepV) u. a. „insgesamt dauerhaft standsicher" sein. Geokunststoffe erfüllten ihre Funktion über einen Zeitrahmen von lediglich mindestens hundert Jahren. Dies stehe somit im Widerspruch wird argumentiert. Das neue LANUV-Arbeitsblatt 33 schließt daher im Moment eine Entlassung aus der Nachsorge von Deponien faktisch aus, wenn in den Böschungen Geokunststoffprodukte eingesetzt wurden. Auch der Fachbeirat der BAM zur Zulassung von Geokunststoffen, Polymeren und Dichtungskontrollsystemen hat sich daher mit der Thematik beschäftigt. Die aktuelle Situation soll daher auf dieser Grundlage diskutiert werden. KW - Deponieverordnung KW - Nachsorge KW - Geokunststoffe KW - BAM-Zulassung KW - Standsicherheit KW - Langzeitverhalten PY - 2018 SN - 0027-2957 VL - 50 IS - 1 SP - 19 EP - 24 PB - Erich Schmidt Verlag AN - OPUS4-43980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Agency perspectives on geomembrane durability, service life and end of life N2 - Die Präsentation erläutert die Hintergründe der nationalen Anforderungen für die Verwendung von Kunststoffdichtungbahnen in Deponieabdichtungen. Die Beständigkeit wird diskutiert. Anforderungen an das Qualitatsmanagement während der Produktion der Produkte und der Bauphase werden aufgezeigt und die Auswirkungen auf die langzeitige Funktionserfüllung werden beschrieben. T2 - IGS TC-B GeoBarrier Workshop CY - Munich, Germany DA - 06.06.2018 KW - Beständigkeit KW - Kunststoffdichtungsbahnen KW - Deponiebau PY - 2018 AN - OPUS4-45123 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Approval of geosynthetics, polymers and leak detection systems for German landfills N2 - Geokunststoffe spielen sowohl im internationalen als auch im deutschen Deponiebau eine Schlüsselrolle. Seit dem Erscheinen der Deponieverordnung (DepV) im Jahre 2009 bedürfen Geokunststoffe, Polymere und Dichtungskontrollsysteme einer Zulassung durch die BAM, wenn diese in deutschen Deponieabdichtungssystemen eingesetzt werden sollen. Die DepV stellt dabei allgemeine Anforderungen an die Geokunststoffe und den Zulassungsprozess für die Produkte auf. Geokunststoffe müssen danach ihre Funktion unter allen zu erwartenden äußeren und inneren Einflüssen über einen Zeitraum von mindestens 100 Jahren erfüllen. Dichtungskontrollsysteme müssen ihre Funktion über mindestens 30 Jahre erfüllen. Die Anforderungen der DepV werden durch die Zulassungsrichtlinien der BAM in konkrete technische Anforderungen für die Produkte aber auch für das Qualitätsmanagement und den Einbau etc. überführt. Bei der Erarbeitung der Zulassungsrichtlinien wird die BAM durch einen Fachbeirat, der sich aus Experten aus allen relevanten Bereichen zusammensetzt, beraten. Der Vorsitz des Fachbeirats liegt beim UBA. Es soll eine kurze Übersicht über die Produkte und die wichtigsten Anforderungen gegeben werden. Zudem soll erläutert werden, durch welche Maßnahmen in der Produktion und auf der Deponiebaustelle eine gleichbleibende Qualität der Produkte gewährleistet wird. T2 - COLLOQUIUM DEPARTMENT 4 „MATERIALS AND THE ENVIRONMENT” CY - Berlin, Germany DA - 14.11.2018 KW - Deponien KW - Geokunststoffe KW - Polymere KW - Dichtungskontrollsysteme PY - 2018 AN - OPUS4-46659 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Die Zulassung von Geokunststoffen nach der deutschen Deponieverordnung N2 - Seit dem Erscheinen der Deponieverordnung (DepV) bedürfen Geokunststoffe, Polymere und Dichtungskontrollsysteme einer Zulassung durch die BAM, wenn diese in deutschen Deponieabdichtungssystemen eingesetzt werden sollen. Die DepV ermöglicht den Einsatz verschiedener Komponenten. Sie stellt dabei allgemeine Anforderungen an die Geokunststoffprodukte auf. Dadurch beschreibt sie den Stand der Technik für Geokunststoffe, die in deutschen Abdichtungen eingesetzt werden. Diese Anforderungen werden durch die Zulassungsrichtlinien der BAM in konkrete technische Spezifikationen überführt. In dem Beitrag wird eine Übersicht über die Produkte und die entsprechenden Anforderungen gegeben. Zudem soll erläutert werden, durch welche Qualitätsmanagementmaßnahmen eine gleichbleibende Qualität und Funktionserfüllung der Produkte gewährleistet wird. T2 - 14. DEPONIEWORKSHOP Liberec - Zittau 2018 CY - Liberec, Czech Republic DA - 15.11.2018 KW - Deponie KW - Geokunststoffe KW - Polymere KW - Dichtungskontrollsysteme PY - 2018 VL - 14 SP - 149 EP - 158 PB - Technische Universität Liberec, Hochschule Görlitz/Zittau CY - Liberec, Tschechien AN - OPUS4-46660 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Die Zulassung von Geokunststoffen nach der deutschen Deponieverordnung N2 - Seit dem Erscheinen der Deponieverordnung (DepV) bedürfen Geokunststoffe, Polymere und Dichtungskontrollsysteme einer Zulassung durch die BAM, wenn diese in deutschen Deponieabdichtungssystemen eingesetzt werden sollen. Die DepV ermöglicht den Einsatz verschiedener Komponenten. Sie stellt dabei allgemeine Anforderungen an die Geokunststoffprodukte auf. Dadurch beschreibt sie den Stand der Technik für Geokunststoffe, die in deutschen Abdichtungen eingesetzt werden. Diese Anforderungen werden durch die Zulassungsrichtlinien der BAM in konkrete technische Spezifikationen überführt. In dem Beitrag wird eine Übersicht über die Produkte und die entsprechenden Anforderungen gegeben. Zudem soll erläutert werden, durch welche Qualitätsmanagementmaßnahmen eine gleichbleibende Qualität und Funktionserfüllung der Produkte gewährleistet wird. T2 - 14. DEPONIEWORKSHOP Liberec - Zittau 2018 CY - Liberec, Czech Republic DA - 15.11.2018 KW - Deponien KW - Geokunststoffe KW - Polymere KW - Dichtungskontrollsysteme PY - 2018 AN - OPUS4-46661 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas ED - Kim, Bumjoo ED - Kim, Yun-Tae ED - Hong, Gigwon ED - Jung, Young-Hoon ED - Chong, Song-Hun T1 - The “zero leakage” approach and German regulations for geosynthetics used in landfill liner and capping systems N2 - An approach to achieve “zero leakage” is discussed with respect to the experience in Germany, where strict regulations for landfill lining and capping systems have been developed and issued because of large environmental problems related to landfills that accumulated in the 1970’s and 1980’s. These regulations for landfills and geosynthetics which are used in landfill liner and capping systems are shortly described. The main certification requirements for the products as well as conclusions for their use are presented. Using a thick, high quality HDPE geomembrane (GMB), which is installed free of residual waves and wrinkles in intimate contact with a compacted clay liner (CCL) or geosynthetic clay liner (GCL) of very low permeability, by a qualified, experienced, well equipped and properly third‐party controlled installer and which are protected by heavy protection layers designed with respect to long‐term performance of the GMB, may result in a liner or capping system of practically no leakage. This is demonstrated by analyzing results of measurements obtained from permanently installed leak detection systems in combination with HDPE GMBs. T2 - 11th International Conference on Geosynthetics CY - Seoul, Korea DA - 16.09.2018 KW - HDPE geomembrane KW - Landfill liner KW - Leak detection KW - Regulations PY - 2018 VL - 11 SP - 1 EP - 8 AN - OPUS4-46030 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - The “zero leakage” approach and German regulations for geosynthetics used in landfill liner and capping systems N2 - An approach to achieve “zero leakage” is discussed with respect to the experience in Germany, where strict regulations for landfill lining and capping systems have been developed and issued because of large environmental problems related to landfills that accumulated in the 1970’s and 1980’s. These regulations for landfills and geosynthetics which are used in landfill liner and capping systems are shortly described. The main certification requirements for the products as well as conclusions for their use are presented. Using a thick, high quality HDPE geomembrane (GMB), which is installed free of residual waves and wrinkles in intimate contact with a compacted clay liner (CCL) or geosynthetic clay liner (GCL) of very low permeability, by a qualified, experienced, well equipped and properly third‐party controlled installer and which are protected by heavy protection layers designed with respect to long‐term performance of the GMB, may result in a liner or capping system of practically no leakage. This is demonstrated by analyzing results of measurements obtained from permanently installed leak detection systems in combination with HDPE GMBs. T2 - 11th International Conference on Geosynthetics CY - Seoul, Korea DA - 16.09.2018 KW - HDPE geomembrane KW - Landfill liner KW - Leak detection KW - Regulations PY - 2018 AN - OPUS4-46031 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wurzler, Nina A1 - Kleinbub, Sherin A1 - Koerdt, Andrea A1 - Özcan Sandikcioglu, Özlem T1 - Effect of conditioning layers on the attachment and biofilm formation of electroactive bacteria on stainless steel N2 - The characteristics of different molecules chosen as representatives for specific functionalities in conditioning layers play an important role on attachment behavior and later biofilm formation of bacteria. The chemical composition is a major component influencing the attachment but there is a conglomerate of influences. T2 - Eurocorr2018 CY - Krakow, Poland DA - 09.09.2018 KW - Conditioning layer KW - Stainless steel KW - Bacterial attachment PY - 2018 AN - OPUS4-46487 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Comparison of Formaldehyde Concentrations in Emission Test Chambers Using EN 717-1 and EN 16516 N2 - For more than 25 years EN 717-1 (Wood-based panels - Determination of formaldehyde re-lease - Part 1: Formaldehyde emission by the chamber method) is the standard for formalde-hyde emission testing of wooden boards. In 2017 EN 16516 (Construction products - Assess-ment of release of dangerous substances - Determination of emissions into indoor air) was published as a new harmonised standard for the emission testing of construction products. Because test chamber conditions are different, both standards give different concentrations for formaldehyde. To determine a conversion factor four test series were set up with different wooden boards. For a loading of 1 m²/m³ the conversion factor is 1.6. This means that the formaldehyde concentration measured under the conditions of EN 16516 is a factor of 1.6 higher compared to EN 717-1. T2 - Conference on Indoor Air CY - Philadelphia, PA, USA DA - 22.07.2018 KW - Loading factor KW - European standard KW - Construction products KW - Air exchange rate PY - 2018 SP - paper 627 AN - OPUS4-45630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Standardisierte Formaldehyd- (und VOC-) Messungen bei Holzwerkstoffen zur Einspeisung der Daten in Normungsprozesse N2 - UBA und BAM schlagen die Durchführung der Prüfkammermessungen bei 23 °C und 50% relativer Luftfeuchte, einer Beladung von 1,8 m²/m³ und einem Luftwechsel von 0,5 pro Stunde vor. Diese Parameter orientieren sich an der EN 16516, die als zukünftige „Referenznorm“ zu betrachten ist. Die Schmalflächenversiegelung ist auch zukünftig wie in der EN 717-1 beschrieben vorzunehmen. Nach 28 Tagen wird der Mittelwert einer Doppelbestimmung als Endkonzentration („entsprechend der Ausgleichskonzentration“) berechnet. Alternativ dazu kann die Prüfung vorzeitig abgebrochen werden, wenn an 5 Messtagen der Prüfung eine Formaldehydkonzentration von 0,1 ppm nicht überschritten wird. Prüfungen nach der EN 717-1 sollen weiterhin gleichberechtigt möglich sein. Ergebnisse von Messungen, die nach der EN 717-1 ermittelt wurden, sind mit dem Faktor 2,0 zu multiplizieren. Abgeleitete Verfahren wie z.B. das Gasanalyseverfahren sollen weiterhin möglich sein. Das Perforatorverfahren entfällt hier, da eine allgemeine für alle Holzwerkstoffe gültige Korrelationen nicht existiert. Die entsprechenden Änderungen sind in der vom BMUB veröffentlichten „Bekanntmachung analytischer Verfahren für Probenahmen und Untersuchungen für die im Anhang der Chemikalien-Verbotsverordnung genannten Stoffe und Stoffgruppen“ entsprechend zu ändern. T2 - UFOPLAN Workshop CY - Berlin, Germany DA - 22.06.2018 KW - EN 717-1 KW - Prüfkammer KW - Formaldehyd KW - EN 16516 PY - 2018 AN - OPUS4-45632 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Comparison of Formaldehyde Concentrations in Emission Test Chambers Using EN 717-1 and EN 16516 N2 - For many years EN 717-1 (Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method) is the standard for formaldehyde emission testing of wooden boards. In 2017 EN 16516 (Construction products - Assessment of release of dangerous substances - Determination of emissions into indoor air) was published as a new harmonised standard for the emission testing of construction products. Because test chamber conditions are different, both standards give different concentrations for formaldehyde. For the determination of a conversion factor four test series were set up with different wooden boards. T2 - Conference on Indoor Air CY - Philadelphia, PA, USA DA - 22.07.2018 KW - Loading factor KW - Construction products KW - European standard KW - Air exchange rate PY - 2018 AN - OPUS4-45631 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Seeger, Stefan T1 - VOC-Emissions from thermoplastic filaments for 3-D-printing N2 - Summary: A screening test for potential emissions of volatile organic compounds (VOC) was run on different thermoplastic filaments used for 3D printing. The method of direct thermal desorption was used to simulate the high temperatures during the 3D printing process and to identify the main compounds emitted from the filaments. A large number of unexpected compounds were detected that might affect the user’s health and have an impact on indoor air chemistry. Introduction: The use of desktop 3D printers is increasing. Compared to other devices with known emissions, e.g. laser printers, there is still a lack of information on possible emissions of VOC and ultrafine particles during operation and the effect on indoor air quality. Most of the commercially available desktop 3D printers operate with a molten polymer deposition. For this process a solid thermoplastic filament is heated in an extrusion nozzle. Most filaments for desktop 3D printers use either acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) as filament. Alternatives are polyvinyl alcohol (PVA) or polycarbonate (PC). Method: Eight different thermoplastic filaments for 3D printers were analysed by direct thermal desorption followed by GC-MS identification of the emitted substances. Direct thermal desorption was done by desorbing 5 mg of the feedstock for 1 minute at a temperature of 210°C. This is an average temperature for 3D printing with thermoplastic filaments. Results and conclusions: The comparison of the 4 different filament groups showed the highest overall emissions from ABS, followed by PLA, PC and PVA. Filament ABS 2 emitted mainly SVOCs and triphenyl phosphate, the latter has the highest emission for a single compound from all evaluated filaments. Thermoplastic filaments are a new source of VOC emissions due to the high temperatures associated with 3D printing, which can reach up to 270°C. Some of the detected compounds like lactic acid, lactide and bisphenol A have never been described before in the indoor environment. Additionally some of the main substances could not be identified and some others might have the potential to affect the indoor air chemistry. The appearance of some newly detected compounds raises concerns about potential health effects for the users of 3D printers at home. T2 - 20th Conference | Odour and Emissions of Plastic Materials CY - Kassel, Germany DA - 20.03.2018 KW - VOC KW - Emissions KW - 3D printing KW - Thermoplastic filaments PY - 2018 AN - OPUS4-44551 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian ED - Martins, I. M. ED - Ulsen, C. ED - Villagran, Y. T1 - Advantages of recycling gypsum plasterboards N2 - Advantages of recycling gypsum plaster boards During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites. Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted. This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process. T2 - IV International Conference Progress of Recycling in the Built Environment CY - Lisbon, Portugal DA - 11.10.2018 KW - Environmental evaluation KW - Gypsum KW - CDW processing PY - 2018 SN - 978-2-35158-208-4 VL - PRO 124 SP - 243 EP - 250 PB - Rilem publications S.A.R.L. CY - Paris AN - OPUS4-48078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Adam, Christian T1 - Advantages of recycling gypsum plasterboards N2 - During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites. Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted. This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process. T2 - IV International Conference Progress of Recycling in the Built Environment CY - Lisbon, Portugal DA - 11.10.2018 KW - Environmental evaluation KW - CDW processing KW - Gypsum PY - 2018 AN - OPUS4-48079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Oberender, Christof A1 - Dosch, Klaus T1 - Ressourceneffizienz bewerten - Ansätze im VDI N2 - Vorstellung von methodischen Grundlagen für eine Ressourceneffizienzanalyse T2 - 3. Fachkonferenz "Stärkung des Einsatzes von mineralischen Recycling-Baustoffen" CY - Potsdam, Germany DA - 05.03.2018 KW - Ressourceneffizienz PY - 2018 AN - OPUS4-46683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Aktueller Stand der Mantelverordnung N2 - Übersicht über Hintergrund, Inhalt und aktuellen Stand der Mantelverordnung. T2 - Baustoffseminar in Weimar - Aktuelles aus der Welt der Gesteinskörnungen CY - Weimar, Germany DA - 10.04.2018 KW - Mantelverordnung PY - 2018 AN - OPUS4-46672 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -