TY - CONF A1 - Wöhlecke, Andreas T1 - The role of junction strength in the performance of geogrids N2 - Designing the performance of geogrids in reinforce soil constructions usually does not consider long-term behavior and possible failure modes of junctions between longitudinal and transverse ribs. How could behavior of junctions be included? To which extend is it necessary? On the conference Geo-Chicago 2016, Swan and Yuan presented an ultimate limit state equation for the short-term material resistance of junctions. We discuss limitations and suggest improvements to include long-term behavior of junctions. Nevertheless, the approach applies only to a specific mode of shear-tensile failure of junctions and only to strictly rigid geogrids. A new design concept presented in the same year by Jacobs on the conference GeoAmerica for the special case of the anchorage of geogrids, which reinforce capping system on long and steep slopes of landfills, tried to overcome these drawbacks. We discuss the aspects of this concept related to the long-term behavior of junctions and the interplay between the load applied to junctions and the flexibility of longitudinal ribs. This interplay and the long-term junction strength determine the long-term behavior of geogrids. T2 - GeoAmericas 2020 CY - Online meeting DA - 26.10.2020 KW - Geogitter KW - Geokunststoffe KW - Deponie PY - 2020 AN - OPUS4-51485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussion aus dem Fachbeirat der BAM N2 - Das Jahr 2020 war vor allen Dingen von der Pandemie geprägt, die alle Bereiche des Lebens und Arbeitens beeinflusst hat und immer noch beeinflusst. Dies hat sich auch auf verschiedene Maßnahmen im Zusammenhang mit zugelassenen Produkten ausgewirkt. In diesem Zusammenhang sollen die Punkte kurz aufgeführt werden. Des Weiteren soll aufgezeigt werden, wie bei der Bearbeitung der Richtlinien, der Zulassungstätigkeit und Beurteilung der Produkte an der BAM und im Fachbeirat vorgegangen wird. Darüber hinaus soll noch einmal kurz auf die Entlassung aus der Nachsorgephase eingegangen werden. Am Ende sollen verschiedene aktuelle Fragestellungen des Fachbeirat aufgezeigt werden. T2 - 17. Leipziger Deponiefachtagung CY - Online meeting DA - 02.03.2021 KW - Deponie KW - Geokunststoffe KW - Kunststoffdichtungsbahn PY - 2021 AN - OPUS4-52213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus dem Fachbeirat der BAM N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. Besondere Aufmerksamkeit gilt der Diskussion um die Einbauhilfe im Schutzschichtsystem, der Einführung einer europäischen Zugversuchsnorm für Kunststoffdichtungsbahnen sowie der Fremdüberwachung der Produktion geosynthetischer Komponenten. Darüber hinaus werden neue Anforderungen an Edelstahlelektroden in Dichtungskontrollsystemen und die Spannungsrissbeständigkeit von PE-HD-Dichtungsbahnen thematisiert. T2 - 35. Karlsruher Deponie- und Altlastenseminar CY - Karlsruhe, Germany DA - 15.10.2025 KW - Deponie PY - 2025 AN - OPUS4-64410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussionen aus dem Fachbeirat der BAM N2 - Im Folgenden soll über aktuelle Diskussionen und Arbeitsschwerpunkte im Fachbeirat der BAM und von der Zulassungsstelle berichtet werden. Es werden Änderungen im Zusammenhang mit der Zulassungsrichtlinie für Kunststoffdichtungsbahnen vorgestellt. Es wird über die aktuelle Diskussion über die Anforderungen z. B. an metallische Sensoren für Dichtungskontrollsysteme berichtet. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden aufgezeigt. T2 - 20. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 12.03.2024 KW - Deponie KW - Kunststoffdichtungsbahn KW - Dichtungskontrollsystem PY - 2024 AN - OPUS4-59894 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Themen aus der Arbeit des Fachbeirats der BAM N2 - Es wird über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet. So wurde in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert. Die Unterarbeitsgruppe Fremdüberwachung in der Produktion hat getagt. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoffdichtungsbahnen, Kunststoff-Dränelemente und für die Fremdüberwachung kurz vorgestellt. T2 - 16. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 03.03.2020 KW - Deponie KW - Geogitter KW - Kunststoffdichtungsbahnen PY - 2020 AN - OPUS4-50509 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus der Arbeit des BAM-Fachbeirats N2 - Der Fachbeirat kommt bereits seit 13 Jahren in seiner jetzigen Form zusammen, um Zulassungsrichtlinien, weitere Dokumente und fachliche Fragestellungen zu beraten. Die Zeit bringt auch personelle Veränderungen mit sich, darüber wollen wir berichten. Derzeit wird die Zulassungsrichtlinie für Schutzschichten im Fachbeirat und in seiner Arbeitsgruppe Geotextilien und Kunststoff Dränelemente (AG Geotextilien) überarbeitet. Zudem wurde die Zulassungsrichtlinie für Kunststoffdichtungsbahnen auf den aktuellen Stand der Regelsetzung und Normung gebracht. Bestimmte Medien, die hier bei einigen Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Hier werden die Hintergründe und Zusammenhänge in Kürze aufgezeigt. Zuletzt wird die Diskussion in Bezug auf den Einsatz von Rezyklaten in den zugelassenen Produkten aufgeführt. T2 - Karlsruher Deponie- und Altlastenseminar 2022 CY - Karlsruhe, Germany DA - 19.10.2022 KW - Deponie KW - Abdichtungssystem KW - Schutzschichten PY - 2022 AN - OPUS4-56210 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Die Spannungsrissbeständigkeit von Kunststoffdichtungsbahnen aus PE-HD und die Zulassungsrichtlinie für Schutzschichten N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen der Zulassungsrichtlinie für Schutzschichten im und durch den Fachbeirat vorgestellt werden. T2 - 19. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 14.03.2023 KW - Deponie KW - Kunststoffdichtungsbahn KW - Spannungsrissbeständigkeit PY - 2023 AN - OPUS4-57195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Zum Spannungsrissverhalten von PE-HD Kunststoffdichtungsbahnen und zu aktuellen Themen aus dem Fachbeirat der BAM N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen im Zusammenhang mit der Zulassungsrichtlinie für KDB vorgestellt werden. Der aktuelle Stand der Diskussion im Zusammenhang mit den verwendeten Tensiden in Bezug auf die Spannungsrissprüfung und weiterer Prüfungen wird aufgezeigt. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden in Kürze aufgezeigt. T2 - Karlsruher Deponie- und Altlastenseminar 2023 CY - Karlsruhe, Germany DA - 18.10.2023 KW - Deponie KW - Kunststoffdichtungsbahn KW - Spannungsrissbeständigkeit PY - 2023 AN - OPUS4-58634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wittwer, Philipp T1 - Herausforderungen bei der Anwendung von Summenparametern (EOF) in der PFAS Analytik N2 - Problemstellen die bei der Arbeit mit der CIC in unserem Fachbereich aufgetreten sind und wie wir diese Probleme angegangen sind und die verwendeten Methoden weiterentwickelt haben. T2 - 25.Jahrestagung SETAC & GDCh "Umwelt 2021" CY - Online meeting DA - 07.09.2021 KW - PFAS KW - EOF KW - CIC PY - 2021 AN - OPUS4-53267 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Poelke, Birte A1 - Klein, Luise A1 - Rohloff, Alexander A1 - Hoffmann, Holger T1 - Initial VOC Emissions from Consumer Products Determined in Micro-Scale Test Chambers: Results of a Round Robin Test N2 - Emissions of volatile organic compounds (VOCs) from consumer products may have a negative impact on indoor air quality, potentially also affecting human wellbeing. Since consumers may be exposed to these VOCs immediately after e.g. unwrapping of newly purchased products, reliable analytical methods are needed to determine air concentration profiles in the early phase of VOC emissions. Concerning typical sample sizes of consumer products, micro-scale test chambers (μ-chambers) were considered suitable for this purpose. In addition, compared to medium- or large-scale test chambers, μ-chambers require lower initial investment and operational costs, and offer options for emissions screenings where higher sample throughput is essential. For these reasons, a μ-chamber-based method to determine initial concentrations of VOCs emitting within the first hours of simulated product use was developed. The chamber air was frequently sampled on desorption tubes loaded with Tenax® TA, followed by quantification of emitted VOCs via thermal desorption gas chromatography mass spectrometry (TD-GC-MS). The method was assessed in a round robin test involving eight participating laboratories from 2 countries. Pieces of a rain poncho (sample area A: 2.01·10-4 m2) emitting cyclohexanone, phenol, 2-ethylhexanol, naphthalene and isophorone in significant concentrations were distributed as sample material. Each laboratory conducted triplicate emission tests over a period of 48 h in μ-chambers with volumes of 44 or 114 mL. The loading factors L of 4.57 m2·m-3 (44 mL) or 1.76 m2·m-3 (114 mL) and air flow rates of 24 mL·min-1 resulted in area-specific air flow rates q of 7.17 m3·m-2·h-1 in both chamber types. The temperature was set to 23°C and, if possible, relative humidity was set to approx. 50%. The chamber air was sampled after 0.5, 1, 2, 4, 24 and 48 hours. In addition, to assess the analytical performance, each participating laboratory received two analyte-spiked Tenax® TA-loaded desorption tubes for quality control (QC). Very low relative standard deviations (11–17%) were obtained for the QC test. The results of the emissions tests in the early phase (0.5–4 h) were also adequate, with acceptable z scores (|z|≤2.00) received by six to seven participating laboratories. All eight laboratories obtained acceptable z scores after the longer sampling periods (24 and 48 h). Hence, the inter-laboratory comparability of the results obtained with the developed μ-chamber method was successfully confirmed. T2 - Healthy Buildings Europe 2025 CY - Reykjavik, Iceland DA - 08.06.2025 KW - VOC Emissions KW - Consumer Product KW - Test Chamber KW - Round Robin Test PY - 2025 AN - OPUS4-63706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Contaminants of Emerging Concern from Materials and Products: Measurement and Evaluation N2 - Test chamber measurements are an important tool to improve indoor air quality and occupational safety. Test chamber measurements are possible for a wide range of materials, products and technologies. Determination of concerning contaminants is important to ensure good indoor air quality. The detection of concerning contaminants depends on the approriate sampling and analysis. T2 - Webinar BAM-University of Birmingham CY - Online meeting DA - 24.02.2021 KW - Emerging Contaminants KW - Emission Test Chamber KW - Thermal Extraction KW - Thermal Desorption PY - 2021 AN - OPUS4-52262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Harmonised test standard EN 16516 - common approach for all building products for interiors N2 - The presentation gives general information about the European Standard EN 16516 “Construction products – Assessment of release of dangerous substances – Determination of emissions into indoor air”. This test standard was developed based on the mandate M/366 of the European commission and is a horizontal reference method for the determination of volatile organic compounds (VOC) from different classes of construction (building) products. Specific test conditions are to be selected by the product TCs (technical committees) in a way that a product is tested under its intended condition of use. The test is based on the use of emission test chambers which are operated at constant air change rate and climate (23°C, 50 % r.h.) over 28 days. The standard defines the conditions and requirements for the measurement including loading factor, air change rate, sampling, analysis and calculation of emission rates of the substances. A 30 m³ reference room is described which is used to calculate air concentrations from the determined emission rates. The standard EN 16516 enables the evaluation of construction products regarding their emissions into indoor air under defined and comparable conditions. The evaluation includes the determination of identified target compounds, non-identified target compounds, volatile carcinogenic compounds and the sum values TVOC, TSVOC and R. T2 - UBA Conference - Limiting health impacts of construction products regarding VOC CY - Online meeting DA - 20.04.2021 KW - Building products KW - EN 16516 KW - Emisson testing KW - Construction products PY - 2021 AN - OPUS4-58079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wen, Keqing T1 - In situ analysis of biofilm formation under different flow regimes with the help of a microfluidic platform N2 - Bacteria often live in habitats characterized by fluid flow, which is ubiquitous in a diverse range of environments such as surface waters, wastewater treatment facilities, pipelines, and medical implants. Bacterial adhesion on surfaces may lead to biocorrosion and biodegradation. In comparison to traditional static and macro flow chamber assays for biofilm formation studies, microfluidic chips allow in situ monitoring of biofilm formation and biofilm related gene expression under various flow regimes. We developed a complete microfluidic platform to investigate biofilms under precisely controlled flow conditions. This platform central unit is a single-inlet microfluidic flow cell with a 5 mm wide chamber tested and analyzed by imaging tracking velocimetry (PIV) to achieve ultra-homogenous flow in the central area of the chamber. Additionally, dedicated microstructures were introduced to the chamber’s center to favor and localize bacterial adhesion and biofilm formation pattern. The flows and vortices induced by the structure were analyzed by computational fluid dynamics (CFD) and related to shape and dimension of the biofilm formed by Escherichia coli TG1. The major proteinaceous component of E. coli biofilms are extracellular amyloid fibers (curli) consisting of major (CsgA) and minor (CsgB) subunits. We used the promotor probe plasmid pRU1701 to monitor csgB-promotor activity under different flow regimes in complex and minimal medium. For comparison, csgB promotor activity in a batch liquid culture and curli production on LB and M9 agar plates were assessed. The microfluidic platform represents a powerful and versatile tool for studying biofilm in flow. The setup shows great potential for the yet not too much explored in flow monitoring of biofilm formation and related gene expression under hydrodynamic stresses. T2 - International Biodeterioration and Biodegradation Symposium (IBBS) 19 CY - Berlin, Germany DA - 09.09.2024 KW - Microfluidics KW - Biofilm KW - Escherichia coli KW - Curli PY - 2024 AN - OPUS4-61911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Einführung in die Mantelverordnung - Stand der Bundes-Bodenschutz- und Altlastenverordnung N2 - Einführung in die Mantelverordnung Stand der Bundes-Bodenschutz- und Altlastenverordnung, aktuelles zum Aufbau der MVO und zum Stand Anfang 2023 T2 - X. Baustoffseminar - Aktuelles zu Gesteinskörnungen CY - Bad Berka, Germany DA - 17.01.2023 KW - Mantelverordnung KW - Gesteinskörnungen KW - Wiederverwertung PY - 2023 AN - OPUS4-57798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Entwicklungen im Gipsrecycling N2 - Gips gehört zu den nachgefragtesten Baustoffen und entsprechend steigt der Gipsverbrauch weltweit schon seit Jahrzehnten an. In Deutschland wird der Gipsbedarf seit vielen Jahren zu einem guten Teil durch REA-Gips, einem Nebenprodukt aus der Abgasreinigung von Kohlekraftwerken, gedeckt. Die weitere Gipsversorgung erfolgt größtenteils durch die Nutzung natürlicher Gipsvorkommen. Ein geringer, aber steigender Anteil an RC-Gips aus dem Baustoffrecycling und die Nutzung synthetischer Gipse aus Nebenprodukten anderer Industriezweige sind ebenfalls zu verzeichnen. Aufgrund der nationalen Klimaschutzziele und der damit verbundenen Abschaltung von Kohlekraftwerken wird das REA-Gipsangebot in den nächsten Jahren jedoch weiter deutlich zurückgehen, so dass andere Gipsquellen erschlossen werden müssen. Abhängig von der Lebensdauer der verwendeten Gipsprodukte im Bausektor ist infolge des in den vergangenen Jahren erfolgten Anstiegs des Gipsverbrauchs auch mit einer Zunahme von Gipsresten in Bau- und Abbruchabfällen zu rechnen. Im Hinblick auf eine bevorstehende Verknappung von Gips wird die Rückgewinnung dieser Gipse aus Bau- und Abbruchabfällen immer wichtiger. Das Recycling von Gipskartonplatten ist mittlerweile eine etablierte Technik und wird bereits seit einigen Jahren in industriellem Maßstab durchgeführt. Außerdem werden neue Verfahren zur Wiederverwertung weiterer Gipsprodukte aus Rück- und Umbaumaßnahmen untersucht. Von besonderem Interesse sind verschiedene Arten von Gipsplatten, da sie gut für selektiven Rückbau geeignet sind. Daher können sie vergleichsweise frei von Verunreinigungen oder Störstoffen zurückgewonnen werden, was für das Gipsrecycling besonders wichtig ist. In dem vom Bundesministerium für Bildung und Forschung geförderten Forschungsprojekt "GipsRec 2.0" werden technische, wirtschaftliche und ökologische Aspekte des Recyclings von Gipsfaserplatten sowie von verschiedenen Synthesegipsen untersucht und bewertet. Die Aufbereitung von Gipsfaserplatten erfolgte im halbtechnischen Maßstab, an verschiedenen potentiellen Ausgangsstoffen für synthetische Gipse wurden Laborversuche durchgeführt. Erfolgversprechende Verfahrenswege werden ökobilanziell bewertet. Ziel dieser Arbeiten ist die Erschließung der Sekundärrohstoffpotenziale von weiteren Quellen für die RC-Gipsproduktion um mit einer Steigerung des Gipsrecyclings die in naher Zukunft durch die Reduktion der REA-Gips-Bereitstellung entstehende Lücke in der Rohstoffversorgung zu verringern. T2 - 21. ibausil 2023 CY - Weimar, Germany DA - 13.09.2023 KW - Baustoffrecycling KW - Sekundärgipse KW - Ökobilanz PY - 2023 AN - OPUS4-60314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Neue Ansätze beim Gipsrecycling N2 - Gypsum is widely used in the construction sector, and its worldwide consumption has been increasing now for several decades. Currently, the gypsum demand is met up to 60% by FGD gypsum (a by-product from coal-fired power plants) in Germany. The natural gypsum deposits cover the remaining gypsum demand. Due to national climate protection goals and the related shutdown of coal-fired power plants, the FGD gypsum supply will decrease significantly in the coming years and, therefore, other gypsum sources must be found. Depending on the lifetime of the used gypsum products in the construction sector, an increase of gypsum in construction and demolition waste is to be expected. With regard to an upcoming shortage of gypsum, several approaches are being tested to recover gypsum from construction and demolition waste. Gypsum plasterboard recycling is already implemented on an industrial scale. Furthermore, new processes to recycle different types of gypsum products from construction and demolition waste are being examined. Of particular interest are different types of gypsum boards because they are well suited for selective dismantling. Therefore, they can be recovered comparatively free of impurities which is most important for the gypsum recycling. In the research project “GipsRec 2.0”, funded by the Federal Ministry of Education and Research, recycling methods for gypsum fiberboards are being investigated. Additionally, the suitability of different types of synthetic gypsum as substitutes for FGD gypsum is being considered. Currently, the quantities of recycled gypsum are not sufficient with regard to the reduction of FGD gypsum. An increase of gypsum recycling should be achieved to narrow the future gypsum gap that will occur in the near future. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 13.09.2021 KW - Gipsabfälle KW - Gipsrecycling KW - Nachhaltigkeit PY - 2021 AN - OPUS4-53682 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Baustoffrecycling: Kreislaufwirtschaft und Umweltschutz N2 - Aktuelle Zahlen zum Baustoffrecycling Zielkonflikte im Kontext von Abfallwirtschaft, Boden- und Grundwasserschutz sowie rechtlichen Vorgabe mit den Beispielen rezyklierte Gesteinskörnungen und RC-Gips. T2 - IX. Baustoffseminar CY - Weimar, Germany DA - 11.03.2020 KW - Kreislaufwirtschaft KW - Baustoffrecycling KW - Ressourcenschonung PY - 2020 AN - OPUS4-51436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - New sources for secondary gypsum N2 - In order to protect natural gypsum deposits and to compensate for the decreasing amount of Flue Gas Desulfurization (FGD) gypsum it is necessary to develop and explore new sources of gypsum. For this purpose, the potentials of different gypsum wastes are investigated in the study “GipsRec 2.0”, funded by the Federal Ministry of Education and Research (Germany). On the one hand, the project worked on a new processing technology for gypsum fiberboards (GFB). While the recycling of gypsum plasterboards has already been carried out on an industrial scale for several years, the recycling of gypsum fiberboards (GFB) has proven to be challenging. Gypsum fiberboards from demolition sites and offcuts from GFB production were used for these investigations. The tests were conducted on a technical scale. Furthermore, various synthetic gypsums are being investigated with regard to their suitability for gypsum production. The analyses are carried out on production residues. In this project, a promising process for gypsum fiberboard recycling could be developed, as well as other waste gypsums are investigated and evaluated with regard to their potential as secondary raw material. In addition, selected process routes are assessed for their environmental impact using a life cycle assessment (LCA) approach. T2 - RILEM - V International Conference Progress of Recycling in the Built Environment CY - Weimar, Germany DA - 10.10.2023 KW - Gypsum recycling KW - Gypsum fiberboards and synthetic gypsum KW - Environmental evaluation PY - 2023 AN - OPUS4-60316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Biorezeptivität und Optimierung von Lehmbaustoffen - Forschung an der BAM N2 - Der Vortrag fasst die Forschungsaktivitäten der BAM in den Themengebieten Biorezeptivität von Beton und Optimierung von Lehmbaustoffen zusammen. Er diente als Kurzpräsentation für eine anschließende Podiumsdiskussion. T2 - Transformationsdialog "Material als Motor" CY - Berlin, Germany DA - 10.10.2024 KW - Biorezeptivität KW - Beton KW - Lehmbaustoffe PY - 2024 AN - OPUS4-62220 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Living Concrete Walls: Engineering Bioreceptivity and Biofilms N2 - Building envelopes are a natural habitat of subaerial biofilms and can be more or less prone to be colonized (i.e. to be bioreceptive). Focusing on the added value of biofilms on manmade substrates represents new aesthetic frontiers and reduces the use of biocides. Moreover, the metabolic processes of photosynthetic biofilms can positively influence human health and life quality in densely populated cities by converting or absorbing pollutants. In the presented research the bioreceptivity of concrete claddings for building facades is engineered to sustain either natural or artificial establishment of microalgae-dominated biofilms. To be able to differentiate between the intrinsic material properties and the climatic boundary conditions, the experimental design in the first step comprised different analyses with model mono- and multi-species biofilms in sterile conditions and a high control of the environmental parameters. Growth and vitality of the algal component of the biofilms has been assessed with Pulse-amplitude modulation (PAM) fluorometry. T2 - 78th RILEM Annual Week & RILEM International Conference on Sustainable Materials & Structures: Meeting the major challenges of the 21st century - SMS 2024 CY - Toulouse, France DA - 25.08.2024 KW - Bioreceptivity KW - Biofilm KW - Weathering KW - Concrete KW - PAM fluorometry KW - Carbonation PY - 2024 AN - OPUS4-62224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -