TY - JOUR A1 - Stawski, Tomasz A1 - Karafiludis, Stephanos A1 - Pimentel, Carlos A1 - Montes-Hernández, German A1 - Kochovski, Zdravko A1 - Bienert, Ralf A1 - Weimann, Karin A1 - Emmerling, Franziska A1 - Scoppola, Ernesto A1 - Van Driessche, Alexander E.S. T1 - Solution-driven processing of calcium sulfate: The mechanism of the reversible transformation of gypsum to bassanite in brines N2 - Here, we show that calcium sulfate dihydrate (gypsum) can be directly, rapidly and reversibly converted to calcium sulfate hemihydrate (bassanite) in high salinity solutions (brines). The optimum conditions for the efficient production of bassanite in a short time (<5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the better-known behaviour of the bassanite phase in low-salt environments. In low-salinity aqueous solutions, bassanite is considered to be metastable with respect to gypsum and anhydrite, and therefore gypsum-to-bassanite conversion does not occur in pure water. Interestingly, the high-salinity transformation of gypsum-to-bassanite has been reported by many authors and used in practice for several decades, although its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures was inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline phase for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios. KW - Industrial and Manufacturing Engineering KW - Strategy and Management KW - General Environmental Science KW - Renewable Energy, Sustainability and the Environment KW - Building and Construction KW - Calcium sulfate KW - Gypsum KW - Bassanite KW - Scattering KW - Raman KW - In situ KW - Synchrotron KW - BESSY KW - MySpot PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594698 UR - https://www.sciencedirect.com/science/article/pii/S0959652624004591#appsec1 DO - https://doi.org/10.1016/j.jclepro.2024.141012 SN - 0959-6526 VL - 440 SP - 1 EP - 12 PB - Elsevier B.V. AN - OPUS4-59469 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karafiludis, Stephanos A1 - de Oliveira Guilherme Buzanich, Ana A1 - Kochovski, Z. A1 - Feldmann, Ines A1 - Emmerling, Franziska A1 - Stawski, Tomasz T1 - Ni- and Co-Struvites: Revealing Crystallization Mechanisms and Crystal Engineering toward Applicational Use of Transition Metal Phosphates N2 - Industrial and agricultural waste streams (waste water, sludges, tailings, etc.) which contain high concentrations of NH4+, PO43–, and transition metals are environmentally harmful and toxic pollutants. At the same time, phosphorous and transition metals constitute highly valuable resources. Typically, separate pathways have been considered to extract hazardous transition metals or phosphate independently from each other. Investigations on the simultaneous removal of multiple components have been carried out only to a limited extent. Here, we report the synthesis routes for Ni- and Co-struvites (NH4MPO4·6H2O, M = Ni2+ and Co2+), which allow for P, ammonia, and metal co-precipitation. By evaluating different reaction parameters, the phase and stability of transition metal struvites as well as their crystal morphologies and sizes could be optimized. Ni-struvite is stable in a wide reactant concentration range and at different metal/phosphorus (M/P) ratios, whereas Co-struvite only forms at low M/P ratios. Detailed investigations of the precipitation process using ex situ and in situ techniques provided insights into the crystallization mechanisms/crystal engineering of these materials. M-struvites crystallize via intermediate colloidal amorphous nanophases, which subsequently aggregate and condense to final crystals after extended reaction times. However, the exact reaction kinetics of the formation of a final crystalline product varies significantly depending on the involved metal cation in the precipitation process: several seconds (Mg) to minutes (Ni) to hours (Co). The achieved level of control over the morphology and size makes precipitation of transition metal struvites a promising method for direct metal recovery and binding them in the form of valuable phosphate raw materials. Under this paradigm, the crystals can be potentially up-cycled as precursor powders for electrochemical or (electro)catalytic applications, which require transition metal phosphates. KW - Crystallization KW - Struvite KW - Nickel KW - Cobalt KW - Phosphorous recovery KW - Up-cycling KW - Aqueous synthesis PY - 2022 DO - https://doi.org/10.1021/acs.cgd.2c00284 VL - 22 IS - 7 SP - 4305 EP - 4315 PB - ACS Publications CY - Washington D.C. AN - OPUS4-55286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kittner, Maria A1 - Coesfeld, Bianca A1 - Schlau, Sven A1 - Werischak, Thomas A1 - Altmann, Korinna A1 - Kalbe, Ute T1 - Simultaneous sampling for microplastics and environmental contaminants from artificial turf: development of a new integrated microplastics eluate lysimeter N2 - To get a better understanding of potentially harmful contaminant emissions from soils or materials into the environment, politics demand practical and holistic sampling concepts for environmental samples such as leachates containing polycyclic aromatic hydrocarbons (PAH) or heavy metals, and hazardous particulate matter like microplastics (MP). Of particular concern are MP emissions from artificial turf sports pitches. So far, there has been only very limited data on MP mass emissions from artificial turf potentially posing a risk to the groundwater and no sampling device that allowed simultaneous sampling for dissolved and particulate contaminants. In this study, a novel integrative microplastics eluate lysimeter was developed to determine contaminant emissions from three artificial turf systems at different ageing states (fabric-new, artificially aged, real-time aged). For the accelerated ageing, all environmental simulation parameters were based on Central German conditions and simulated outdoor stress during the turf service lifespan of 15 years. MP masses from eluates were analysed using thermal extraction desorption-gas chromatography/mass spectrometry, PAH concentrations using gas chromatography/mass spectrometry and heavy metals using inductively coupled plasma-optical emission spectroscopy. Results showed that no PAH or heavy metal concentrations from the seepage water were above German legal limits for alternative granular construction materials considering soil and groundwater protection. Furthermore, it was found that only minimal MP emissions were released from new turf systems into the seepage water (< 1 mg/m2). Ageing of the artificial turf increased MP formation, especially from rubber infill and grass fibres, which are then carried into the seepage water. The highest total MP emissions over a simulated turf lifespan of 15 years were detected in two real-time aged turf systems ranging from 136.4–252.5 mg/m2. Considerably less total MP emissions were detected in accelerated aged artificial turf systems, one of which contained a synthetic rubber infill (5.4–8.0 mg/m2) and one without rubber infill (0.2–5.3 mg/m2). In summary, it was demonstrated that the newly developed MEL generated reliable and reproducible data and has thus proven itself as an integrated, straightforward and automated sampling device for simultaneous monitoring of particulate and dissolved pollutant emissions from simple soil matrices. KW - Lysimeter KW - Microplastics KW - Artificial turf KW - Thermal extraction desorption-gas chromatography/mass spectrometry KW - TED-GC/MS KW - Polycyclic aromatic hydrocarbons KW - PAH KW - Heavy metals KW - Soil samples PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-645301 DO - https://doi.org/10.1186/s12302-025-01235-1 SN - 2190-4715 VL - 37 IS - 1 SP - 1 EP - 15 PB - Springer Open AN - OPUS4-64530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Herzel, Hannes A1 - Grevel, K.-D. A1 - Emmerling, Franziska A1 - Dachs, E. A1 - Benisek, A. A1 - Adam, Christian A1 - Majzlan, J. T1 - Thermodynamic properties of calcium alkali phosphates Ca(Na,K)PO4 N2 - Calcium alkali phosphates Ca(Na,K)PO4 are main constituents of bioceramics and thermochemically produced phosphorus fertilizers because of their bioavailability. Sparse thermodynamic data are available for the endmembers CaNaPO4 and CaKPO4. In this work, the missing data were determined for the low-temperature phase modifications of the endmembers CaNaPO4 and CaKPO4 and three intermediate Ca(Na,K)PO4 compositions. Standard enthalpy of formation ranges from - 2018.3 ± 2.2 kJ mol-1 to - 2030.5 ± 2.1 kJ mol-1 and standard entropy from 137.2 ± 1.0 J mol-1 K-1 to 148.6 ± 1.0 J mol-1 K-1 from sodium endmember b-CaNaPO4 to potassium endmember b0-CaKPO4. Thermodynamic functions are calculated up to 1400 K for endmembers and the sodium-rich intermediate phase b-Ca(Na0.93K0.07)PO4. Functions above 640 K are extrapolated because of the phase transition from low- to high-temperature phase. Impurities in the synthesized intermediate phases c-Ca(Na0.4K0.6)PO4 and c-Ca Na0.35K0.65)PO4 and one additional phase transition around 500 K impeded the determination of high-temperature thermodynamic functions. In general, data for phase transition temperatures agree with the previously reported phase diagrams. KW - Formation enthalpy KW - Heat capacity KW - Phase transformation KW - Bioceramics KW - Phosphorus fertilizer KW - Entropy PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-507640 DO - https://doi.org/10.1007/s10853-020-04615-5 VL - 55 SP - 8477 EP - 8490 PB - Springer AN - OPUS4-50764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwibbert, Karin A1 - de Eulate Pérez, Elisa García A1 - Wen, Keqing A1 - Voss, Heike A1 - Thiele, Dorothea A1 - Richter, Anja M. A1 - Bonse, Jörn T1 - Escherichia coli repellence via laser-induced periodic surface structures (LIPSS) on titanium: Critical role of biofilm-associated gene expression N2 - The inconsistency in the observed bacteria-repellent effects of laser-induced surface textures remains a subject of scientific debates. With E. coli TG1 as test strain, we performed biofilm formation assays on ultrashort pulse laser textured titanium. Samples covered with low spatial frequency LIPSS (LSFL) of periods around 750 nm or with high spatial frequency LIPSS (HSFL) featuring smaller periods around 100 nm were processed on polished samples. While LSFL significantly reduce the number of adhering bacteria compared to the polished reference, HSFL do not. Simultaneously, we concentrate our study on bacterial strategies employed for biofilm formation, that is the transcription of the biofilm-associated genes csgB, involved in primary adhesion to a surface, and wza, participating in biofilm maturation. Promoter regions of these genes were cloned into a promotor probe plasmid with the green fluorescent protein GFP+ as reporter and transferred into the test strain. As indicated by the fluorescence intensity of the reporter protein, among the bacteria colonizing LSFL-covered areas, a markedly higher proportion of cells transcribing csgB or wza were detected, compared to the bacterial populations colonizing the polished or HSFL-covered areas. To our knowledge, this is the first study indicating that the antifouling effect of LSFL topographies can be counteracted when bacteria activate biofilm-associated genes. KW - Laser-induced periodic surface structures (LIPSS) KW - Titanium KW - Biofilm KW - Antifouling KW - Gene expression KW - Fluorescence microscopy PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655572 DO - https://doi.org/10.1016/j.apsusc.2026.166363 SN - 0169-4332 VL - 730 SP - 1 EP - 9 PB - Elsevier B.V. AN - OPUS4-65557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -