TY - CONF A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Simon, Franz-Georg T1 - CIC & HR-GFMAS: Über Summenparameter in der PFAS-Analytik - Entwicklung von AOF-Parametern anhand Combustion Ion Chromatography N2 - Kurzzsammenfassung der bisherigen Ergebnisse der Vorhaben 4320 und 4390 beim Netzwerktreffen des PerFluSan Netzwerks T2 - Netzwerktreffen PerFluSan CY - Online meeting DA - 19.11.2020 KW - PFAS KW - PFC KW - AOF KW - EOF PY - 2020 AN - OPUS4-51625 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Lisec, Jan A1 - Borca, C. A1 - Huthwelker, T. A1 - Simon, Franz-Georg T1 - Combining DGT and combustion ion chromatography (CIC) as screening tool for per- and polyfluoroalkyl substances (PFAS) contamination in wastewater-based fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of organofluorine surfactants used in the formulations of thousands of consumer goods. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system have been resulted in contaminated effluents and sewage sludge from wastewater treatment plants (WWTPs) which became an important pathway for PFAS into the environment. Because sewage sludge is often used as fertilizer its application on agricultural soils has been observed as significant input path for PFAS into our food chain. To produce high-quality phosphorus fertilizers for a circular economy from sewage sludge, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Normally, PFAS are analyzed using PFAS protocols typically with time-consuming extraction steps and LC-MS/MS target quantification. However, for screening of PFAS contaminations in wastewater-based fertilizers also the DGT technique can be used for the PFAS extraction. Afterwards, combustion ion chromatography (CIC) can be applied to analyze the “total” amount of PFAS on the DGT binding layer. The DGT method was less sensitive and only comparable to the extractable organic fluorine (EOF) method values of the fertilizers in samples with >150 µg/kg, because of different diffusion properties for various PFAS, but also kinetic exchange limitations. However, the DGT approach has the advantage that almost no sample preparation is necessary. Moreover, the PFAS adsorption on the DGT binding layer was investigated via surface sensitive spectroscopical methods, such as Fourier-transform infrared (FT-IR) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - DGT Konferenz CY - Paris, France DA - 11.10.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge PY - 2023 AN - OPUS4-58575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Wiedergewinnung von Rohstoffen aus Abfall N2 - Der Vortrag führt aus, wie Sekundärrohstoffe aus Abfällen gewonnen werden. Dabei wird auch auf die Umweltverträglichkeit der Produkte eingegangen. T2 - Weiterbildung für Efb-Sachverständige, Mitarbeiter von Entsorgungsunternehmen und Umweltbehörden CY - Berlin, Germany DA - 04.01.2018 KW - Sekundärrohstoffe KW - Stoffstromanalyse KW - Kreislaufwirtschaft PY - 2018 AN - OPUS4-44941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Rückgewinnung von Aluminium aus Abfällen N2 - Abtrennung von Nichteisenmetallen aus Müllverbrennungsaschen T2 - IFAT, Messe für Wasser-, Abwasser-, Abfall- und Rohstoffwirtschaft CY - München, Germany DA - 16.05.2018 KW - Rostasche KW - Kumulierter Energieaufwand KW - Sekundärrohstoffe PY - 2018 AN - OPUS4-44939 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohr, Gunther A1 - Seeger, Stefan A1 - Hilgenberg, Kai T1 - Measurement of particle emissions in Laser Powder Bed Fusion (L-PBF) processes and its potential for in-situ process monitoring N2 - Laser Powder Bed Fusion (L-PBF) is a promising additive manufacturing (AM) technology for metal part production especially for complex and lightweight structures or functional designs. In L PBF processes several by-products including welding plume and its condensates, spatter and ejected powder are generated during laser exposure. Investigations of micro- and nano-sized by-products have received little attention in literature. This study focuses on the analysis of particle emissions in L PBF of 316L stainless steel using a scattered light aerosol spectrometer and a fast mobility particle sizer spectrometer during the process which allows for in-situ analysis of particle sizes in the range of 6 nm to 100 µm. A distinct correlation of emission signals to part position can be revealed. In addition, a significant influence of laser scanning vector directions on emission signals is presented. Furthermore, differing powder layer thicknesses can be recognised by deviations in emission signals. T2 - Euro PM2019 CY - Maastricht, The Netherlands DA - 13.10.2019 KW - Aerosol measurements KW - Laser Powder Bed Fusion (L-PBF) KW - Additive Manufacturing (AM) KW - Spatter KW - Fume KW - Plume KW - Particle gas emission PY - 2019 AN - OPUS4-49387 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon A1 - Mohr, Gunther A1 - Baesso, Ilaria A1 - Straße, Anne A1 - Pittner, Andreas A1 - Pignatelli, Giuseppe A1 - Seeger, Stefan A1 - Nazarzadehmoafi, Maryam A1 - Ehlers, Henrik A1 - Gohlke, Dirk A1 - Homann, Tobias A1 - Scheuschner, Nils A1 - Ulbricht, Alexander A1 - Heinrich, P. A1 - Maierhofer, Christiane T1 - Process monitoring of additive manufacturing of metals - an overview of the project ProMoAM N2 - The project ProMoAM is presented. The goal of the project is to evaluate which NDT techniques or combination of techniques is suited for in-situ quality assurance in additive manufacturing of metals. To this end, also 3d-data fusion and visualization techniques are applied. Additional ex-situ NDT-techniques are used as references for defect detection and quantification. Feasability studies for NDT-techniques that are presently not applicable for in-situ use are performed as well. The presentation gives a brief overview of the whole project and the different involved NDT-techniques. T2 - Workshop od Additive Manufacturing: Process, materials, simulation & implants CY - Berlin, Germany DA - 13.05.2019 KW - Additive manufacturing KW - Process monitoring KW - NDT PY - 2019 AN - OPUS4-48087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blotevogel, J. A1 - Lu, W. A1 - Rappé, A. A1 - Kennedy, E. A1 - Stockenhuber, M. A1 - Weber, N. A1 - Lucas, J. A1 - Vogel, Christian A1 - Simon, Franz-Georg A1 - Holm, O. T1 - Thermal Destruction of PFAS N2 - Thermal treatment processes are currently the only full-scale option for thedestruction of per- and polyfluoroalkyl substances (PFAS) in large waste streams. While all organic molecules including PFAS are susceptible to thermal destruction, their decomposition rates are controlled by process variables such as temperature, reaction atmosphere, and residence time. Concerns exist about the formation of products of incomplete destruction and their emission from hazardous waste incinerators. This talk will summarize the current stateof-the-art of thermal PFAS destruction, identify research needs, and showcase future research designed to address critical knowledge gaps. T2 - Department of Defense's (DoD) Energy and Environment Innovation Symposium CY - Washington DC, USA DA - 28.11.2023 KW - Thermal treatment KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Remediation PY - 2023 AN - OPUS4-58974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Scholz, Philipp A1 - Gleis, Markus T1 - Aschen und Schlacken aus der Abfallverbrennung; Gefährlich oder nicht? N2 - In Deutschland fallen aktuell pro Jahr über 5 Mio. Tonnen Hausmüllverbrennungs-aschen (HMVA) an. Eine Verwertung dieser Aschen und Schlacken ist in Deutschland möglich und findet überwiegend im Deponiebau statt. Für die Verwertung sind in der Ersatzbaustoffverordnung Eluatgrenzwerte für Schwermetalle und einige andere Parameter vorgesehen. Der Umgang mit HMVA könnte durch eine Einstufung als gefährlicher Abfall erschwert werden. Maßgeblich für die Einstufung eines Abfalls als gefährlich oder ungefährlich sind die gefahrenrelevanten Eigenschaften HP 1 bis HP 15 nach Anhang III der Richtlinie 2008/98/EG über Abfälle mit dort festgelegten Konzentrationsgrenzen. Für HMVA ist im Wesentlichen nur der Parameter HP 14 (Ökotoxizität) von Bedeutung. Dafür sind entscheidend die Gehalte an chemischen Verbindungen mit den Gefahrenhinweiscodes (hazard statement code, HSC) H400, H410, H411, H412 und H413. Eine detaillierte Diskussion zu den übrigen Gefahreneigenschaften bei HMVA findet sich in der Literatur. Die Einstufung als gefährlicher Abfall erfolgt nach festgelegten Rechenregeln. Die BAM bearbeitet ein durch das UBA gefördertes Forschungsprojekt zur Erfassung und Bewertung von Analysedaten zu Aschen und Schlacken aus Abfallverbrennungsanlagen. Die Ergebnisse des Vorhabens sollen bei der Weiterentwicklung des vorhandenen Konzeptes für eine bundeseinheitlichen Untersuchung und abfallrechtlichen Einordnung von Aschen und Schlacken aus deutschen Abfallverbrennungsanlagen unterstützend herangezogen werden. Im Vortrag werden Verfahren zur quantitativen Bestimmung der einstufungsrelevanten Verbindungen vorgestellt: 1.) der Praxisleitfaden von ITAD und IGAM, 2.) Methode basierend auf der Bioverfügbarkeit und 3.) Methode basierend auf Speziierungsanalyse. T2 - Jahrestreffen 2023 der DECHEMA-Fachgruppen AuW und TRO CY - Dresden, Germany DA - 06.03.2023 KW - Rostasche KW - Speziierungsanalyse KW - Abfallbehandlung PY - 2023 AN - OPUS4-57346 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Simon, Franz-Georg T1 - Per- und polyfluorierte Alkylsubstanzen (PFAS) im Klärschlamm - Analytische Methoden und Grenzwerte N2 - Per- und Polyfluoralkylsubstanzen (PFAS) sind eine Gruppe von mehr als 4700 anionischen und kationischen anthrophonen Stoffen, die aufgrund ihrer inerten chemischen Stabilität und ihrer Widerstandsfähigkeit gegen den Abbau durch Hitze oder Säuren in einer Vielzahl von Produkten verwendet werden. Infolge der ständigen Verwendung, vor allem in Feuerlöschschäumen für die Luftfahrt, wurden in Tausenden von Industrie- und Militäranlagen kontaminierte Böden und Grundwasservorkommen gefunden. Aufgrund der ständigen Verwendung von fluorierten Konsumgütern haben sich jedoch auch Abwässer und Klärschlamm aus Kläranlagen als Quelle für die Kontamination der aquatischen Umwelt mit PFAS erwiesen. Infolge der strengeren Vorschriften und Beschränkungen, die in den letzten Jahren für die Verwendung langkettiger (≥C8) PFAS erlassen wurden, findet in der chemischen Industrie eine deutliche Verlagerung hin zur Herstellung kurz- (C4-C7) und ultrakurzkettiger (C1-C3) Alternativen statt. Mit der Novellierung der Klärschlammverordnung im Jahr 2017 hat der deutsche Gesetzgeber die Ausbringung von Klärschlamm auf landwirtschaftlichen Flächen verboten, und bis 2029/2032 wird die Ausbringung von Klärschlamm in der Landwirtschaft vollständig verboten sein. Während die Belastung der Umwelt mit organischen Schadstoffen wie PFAS, Pestiziden und Arzneimitteln nicht mehr erwünscht ist, muss Phosphor (P) aus Klärschlamm weiterhin zur Herstellung hochwertiger P-Dünger für eine Kreislaufwirtschaft genutzt werden. Derzeit können pflanzenverfügbare P-Düngemittel aus Klärschlamm/Abwasser mit verschiedenen Behandlungsmethoden hergestellt werden, darunter Fällung, Auslaugung und thermische Behandlung. Der Verbleib von PFAS bei der Auslaugung, Ausfällung und Behandlung von Klärschlamm und Abwasser ist jedoch noch weitgehend unbekannt. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 14.11.2022 KW - Klärschlamm KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Phosphor KW - Düngemittel PY - 2022 AN - OPUS4-56291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Pienkoß, Fabian T1 - Das ERA-MIN 2 Projekt BASH-TREAT N2 - Im Rahmen des Projekts wurde 1.) eine vollständige Bewertung des Stands der Technik in der EU bei der Behandlung von Rostasche vorgenommen und 2.) eine Optimierung der Nutzung der Feinfraktion in Labor- und Feldmaßstab untersucht. Das Konsortium bestand aus zwei Universitäten aus Deutschland und Italien, der BAM als Forschungseinrichtung des Bundes und zwei Industriepartnern aus Deutschland und Schweden mit unterschiedlichen und spezifischen Fachkompetenzen. Im Vortrag werden die Ergebnisse des weitgehend abgeschlossenen Projekts BASH-TREAT vorgestellt. T2 - Jahrestreffen der ProcessNet-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung, Energieverfahrenstechnik, Gasreinigung, Hochtemperaturtechnik, Rohstoffe CY - Bamberg, Germany DA - 30.03.2022 KW - Rostasche KW - Thermische Abfallbehandlung KW - Nassaufbereitung PY - 2022 AN - OPUS4-54589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Simon, Franz-Georg A1 - Bandow, Nicole T1 - Potential use of incineration bottom ash in construction – Evaluation of environmental impact N2 - Around 5 million tonnes of MSWI bottom ash (BA) are generated per year in Germany. The incineration itself serves for metals as a concentrating and cleaning process. However, due to the almost exclusive wet extraction out of the furnace chamber the various metals are integrated in a heterogeneous and instable matrix. The metal recovery is therefore still a challenge relating the recovery rate and the purity, respectively. With state of the art treatment trains in Germany around 7.7% of ferrous metals and 1.3% of non-ferrous metals can be recovered out of MSWI BA. Large quantities of the mineral fraction are reused for sub-base material in road construction. A three month ageing period has been established as the common practice of further treatment of bottom ash before reuse applications. In the course of this aging the pH value of bottom ash decreases and contaminants are immobilized by processes like carbonation, hydration and oxidation. In particular leaching of heavy metals may be reduced to environmentally acceptable levels. However, the aging results in fixing of other valuable resources such as metals. Two laboratory scale lysimeters (30 cm in diameter) are being operated for more than three years aiming at the investigation of the long-term leaching behavior of a 0.25/45 mm mineral material obtained by treatment of MSWI bottom ash directly after incineration by a wet processing technology. Artificial rainwater is used as leachant (pH ≈ 6, ingredients NO32-, Cl-, SO42-, Na+, K+, Ca2+, Mg2+). The lysimeters are irrigated related to an average annual precipitation rate of 600 mm/a leading to a liquid to solid ratio (L/S) of about 0.7 per year of operation. Lysimeter tests are more adequate to simulate field scenarios and long-term leaching behavior in contrast to laboratory column tests particularly due to the unsaturated conditions and realistic contact time with the leachant. In comparison to the leaching of bottom ash (aged for 3 month and non-treated) in column tests the chloride and sulfate leaching in the lysimeters was reduced as a consequence of the previous wet processing. The sulfate release kept almost constant limited by CaSO4 solubility up to an L/S of about 0.7 l/kg. The chloride concentrations dropped quickly, starting from 7300 mg/l, and are now at an almost constant level of 50 mg/l which is significantly above the chloride concentration in the leachant. After an initial decrease of the pH from about 10.4 to 8 at L/S of 0.2 l/kg, the pH increased again and leveled out around 9.8 up to L/S 2.2 l/kg. At an L/S of about 2.5 l/kg now, Cr, Cu are still released. The Cu and Cr concentrations in the leachates were about 760 µg/l and 90 µg/l respectively at the beginning. For both metals the concentration decreased to about 35 µg/l now. The Mo concentrations dropped steadily from 1300 to 250 µg/l, whereas V and Sb concentrations increased in the course of the tests. Fe and Mn are not detectable anymore. More results of this experimental study will be presented and discussed with a special focus on elements forming oxyanions. T2 - 10th International Conference on the Environmental and Technical Implications of Construction with Alternative Materials, WASCON 2018 CY - Tampere, Finland DA - 06.06.2018 KW - Lysimeter, Antimony KW - MSWI bottom ash KW - Leaching PY - 2018 AN - OPUS4-45263 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Secondary building materials in a circular economy N2 - Half of the global material consumption is mineral material. The circularity is still low so that enhanced use of secondary building material is required to close loops. Three different secondary building materials are discussed based on exemplary research results: construction and demolition waste (C&D waste), soil-like material and incineration bottom ash (IBA). Focus was laid on the environmental compatibility of the materials examined mainly by standardized leaching tests. C&D waste was investigated after a wet treatment using a jigging machine, soil-like material and IBA were characterized with respect to their material composition. The environmental compatibility in particular was studied using standard leaching tests (batch tests and column tests). It was concluded that soil-like material can mostly be utilized even when the precautionary limit values set are exceeded by a factor of less than 2. For C&D waste the fine fraction below 2 mm and the content of brick material is problematic. IBA fulfills quality level HMVA-2 following German regulation. Higher quality levels of utilization might be achievable with better treatment technologies. T2 - 15th International Conference on Ecomaterials (ICEM15) CY - Iki, Japan DA - 26.11.2023 KW - Secondary building materials KW - Incineration bottom ash KW - Construction and demolition waste KW - Soil-like material PY - 2023 AN - OPUS4-59186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Ludwig, S. A1 - Roesch, Philipp A1 - Vigelahn, L. A1 - Wittwer, Philipp A1 - Birke, V. A1 - Simon, Franz-Georg T1 - Mechanochemical Remediation of Per- and Polyfluoroalkyl Substanzes (PFAS) in Soils N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of anionic, cationic, or zwitterionic organofluorine surfactants used in the formulations of thousands of products and consumer goods, including aqueous film-forming foams (AFFF) used to suppress aviation fires in training scenarios, non-stick cookware, fast-food wrappers, water-repellent fabrics, medical equipment. Because PFAS have been extensively used in a variety of AFFF products they can be found in soils from industrial and military installations. Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Previously, mechanochemical treatment of polychlorinated organic compounds in soils showed an efficient dechlorination. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GCMS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well es the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - CleanUp 2022 CY - Adelaide, Australia DA - 11.09.2022 KW - PFAS KW - Mechanochemical treatment KW - XANES spectroscopy PY - 2022 AN - OPUS4-55742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - EI-GEO (S&T CALL 2017), Environmental impact of geosynthetics in aquatic systems N2 - 2021 marks the 10th anniversary of the first ERA.Net RUS joint call for European-Russian STI cooperation projects. Pooling the resources of more than 20 European and Russian funding agencies, more than 150 projects were funded with an estimated budget of about € 60 million. Being even larger than many thematic ERA.NETs, the ERA.Net RUS Plus has been the biggest and most successful regional ERA.NET so far. Indicating a strong demand for scientific cooperation, the smaller-scale projects funded within the ERA.Net RUS (Plus) calls perfectly complement Russian participation in the EU Framework Programmes. Not least of all, the ERA-Net RUS calls are examples of successful collaboration at a time when cooperation in other fields is complicated by the politically challenging situation. These calls contributed to keeping the communication channels open. Against this background a dedicated event in late 2021 highlighted what has been achieved within the first decade of the initiative. The project EI-GEO coordinated by BAM was selected as best practice project. The presentation displays the main results of the project and discusses the key success factors. T2 - ERA.Net RUS: Celebrating ten years of multilateral European-Russian Research and Innovation cooperation CY - Online meeting DA - 09.12.2021 KW - Geosynthetics KW - Coastal protection KW - European research area PY - 2021 AN - OPUS4-53965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Wiedergewinnung von Rohstoffen aus Abfall N2 - Antimon (Sb) wird in Industrieprodukten hauptsächlich als Flammschutzmittel in Kunststoff verwendet. Aufgrund solcher Zusätze in Kunststoffen landet etwa die Hälfte von Sb am Ende der Lebensdauer in der Verbrennung fester Siedlungsabfälle und folglich in relevanten Mengen in der erzeugten Bodenasche. Bei Kontakt mit Wasser ist die anfängliche Auslaugbarkeit gering, da Antimonat mit Ca2+ schwerlösliche Verbindungen bilden. Nach der Carnonatisierung der Verbrennungsasche (IBA) während der fortschreitenden Alterung nimmt der pH-Wert in den Sickerwasser ab. Mit abnehmender Ca-Konzentration im Eluat ändert sich das Lösungsgleichgewicht und Antimonate lösen sich auf. In Deutschland ist beabsichtigt, Sb in IBA mit der geplanten Umsetzung der sogenannten Mantelverordnung (MantelVO, die Bestimmungen zur Verwertung von Mineralabfällen enthält) in naher Zukunft zu regulieren. Die im Entwurf festgelegten Grenzwerte können für IBA kritisch sein und stellen daher ein Risiko für die Verwendung der Mineralfraktion von IBA in den gut etablierten Recyclingwegen dar. T2 - Weiterbildung für Efb-Sachverständige, Mitarbeiter von Entsorgungsunternehmen und Umweltbehörden (GUT GmbH) CY - Online Meeting DA - 07.01.2021 KW - Rostasche KW - Antimon KW - Auslaugverfahren PY - 2021 AN - OPUS4-52438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Beschleunigte Alterung von Geotextilien zur Ermittlung von Materialeigenschaften N2 - Geokunststoffe werden im Wasserbau häufig eingesetzt, beispielsweise bei Maßnahmen für den Küstenschutz oder in Ballastschichten für Windenergieanlagen. Eine zunehmende Anwendung von Geokunststoffen wird aufgrund der Ausweitung der Offshore-Windenergieerzeugung und des Schutzes auf steigende Wasserspiegel und extremere Wetterbedingungen infolge des Klimawandels beobachtet. Die Anwendung von Geokunststoffen in Wasserbauprojekten bietet zwar verschiedene wirtschaftliche und technische Vorteile, wurde jedoch kürzlich in Frage gestellt, da sich diese Materialien während ihrer Lebensdauer verschlechtern und langfristig gefährliche Auswirkungen auf die aquatische Umwelt haben können, insbesondere als Ursprung von Kunststoffabfällen oder als Quelle / Senke für Chemikalien wie Weichmacher und Stabilisatoren, die bei der Herstellung von Geokunststoffen verwendet werden, um deren Leistung zu verbessern. Der Vortrag geht auf diese Bedenken ein. T2 - Geotextilien im Wasserbau CY - Online Meeting DA - 14.04.2021 KW - Wasserbau KW - Geotextilien KW - Beschleunigte Alterung PY - 2021 AN - OPUS4-52434 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Wünsch, Christoph T1 - Reduction of greenhouse gas emissions in waste management N2 - The production of secondary materials from waste materials requires, in most cases, significantly lower energy amounts than the primary material production of raw materials. Along with lower energy demand, the greenhouse gas emissions produced are also lower. The duty of a modern waste management system should therefore be to collect and sort the waste materials in a way that the highest amounts of single material fractions with the highest qualities can be generated. In this contribution, the greenhouse gas balances of the theoretical treatment of the household waste, if collected as mixed waste in sanitary landfills, in waste incineration plants, or in mechanical-biological treatment plants, are compared to the existing separate waste collection and treatment in Germany in 2014. T2 - Richtlinienausschuss VDI 3925 CY - Insel Vilm, Germany DA - 08.05.2018 KW - Culuative energy demand KW - Greenhouse gas balance KW - Waste management PY - 2018 AN - OPUS4-44940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Scholz, Philipp A1 - Gleis, Markus T1 - Aschen und Schlacken aus der Abfallverbrennung im Lichte der Ersatzbaustoffverordnung N2 - Im Rahmen eines vom Umweltbundesamt geförderten Forschungsprojekts wurde untersucht, ob die Abtrennung der Feinfraktion (0-2 mm) eine Verbesserung der umweltrelevanten Eigenschaften bewirkt und somit HMVA-1 erreicht werden kann. In Deutschland wird die Rostasche durch Nassentschlackungssysteme aus dem Feuerraum ausgetragen. Durch den Kontakt mit Wasser setzen direkt hydraulische Reaktionen ein, die eine vollständige Abtrennung der Feinfraktion unmöglich machen. Das wurde bereits in den 1990er Jahren erkannt und führte zur Entwicklung des ABB InRec Verfahrens mit Trockenentaschung als ersten Verfahrensschritt. Auch damals war das Ziel eine möglichst inerte Rostasche für die Verwertung zu erzeugen. In den letzten Jahren wurden in der Schweiz Trockenentaschungssystem installiert, hier vor allem um die Rückgewinnung von elementaren Metallen auch in der Feinfraktion zu verbessern. Welche Potenziale sich dabei erschließen lassen, wurde in einem anderen UBA-Projekt untersucht. Im Rahmen unserer Arbeiten wurde versuchsweise trockene Rostasche an einer Anlage in Süddeutschland genommen und im Labor untersucht. Im Vortrag werden die Ergebnisse zum Auslaugverhalten und zur Gefahreneigenschaft HP14 (Ökotoxizität) vorgestellt. T2 - Jahrestreffen 2024 der DECHEMA-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung (AuW) und Gasreinigung (GAS) CY - Dresden, Germany DA - 25.03.2024 KW - Rostasche KW - Ersatzbaustoffe PY - 2024 AN - OPUS4-59985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Economic and legal aspects of secondary resource management N2 - Direct and indirect effects (DIERec) of the recovery of secondary resources are in the range of 500 million tonnes per year in Germany; energy savings are 1.4 million TJ. These savings are between 10 and 20% of the total. The effects of materials recovery exceed those of energy recovery by far with the exception of secondary plastic material where DIERec from energy recovery is higher by factor of 2.7. Untapped potential for the recovery of secondary resources exist in the fine fraction of bottom ash from municipal solid waste incineration, mainly Cu and precious metals and in urban mining. T2 - Travelling Conference Resource efficiency and environmental compatibility in waste management (REECO-WM) CY - Seoul, Ho-Chi-Minh-City, Perth DA - 29.01.2018 KW - Waste management KW - Materials flow KW - Secondary resources PY - 2018 AN - OPUS4-44942 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heuser, Lina A1 - de Oliveira Guilherme Buzanich, Ana A1 - Radtke, Martin A1 - Agudo Jácome, Leonardo A1 - Feldmann, Ines A1 - Deubener, J. T1 - Silver diffusion in low-melting alkali zinc borate model glasses studied by means of SNMS, TEM and XAS N2 - In many late-breaking research fields as in photovoltaics, microelectronics, nuclear waste glasses or at least mirror glasses silver diffusion in glasses is relevant to the issues of high-level functionality and recycling. The present study is focused on silver diffusion in innovative, low-melting alkali zinc borate glasses (X2O-ZnO-B2O3, X = Li, Na, K, Rb) potentially usable for silver metallization-pastes in solar cells. The glasses were coated with a thin metallic silver layer and heat treatments in air and nitrogen close to Tg at 470 °C for 2 h were performed. After heat treatment under air and nitrogen atmospheres the coating thickness, measured by a white light interferometer, was about 1.8 µm thick. Silver depth profiles determined by means of secondary neutral mass spectrometry (SNMS) indicate the fastest silver diffusion to a depth of 3.5 µm for Li2O-ZnO-B2O3 (LZB) glass. Nevertheless, the influence of the different alkali ions on the silver diffusion is small. The oxygen availability determines the silver diffusion into the glasses. The oxygen promotes the oxidation of the silver layer enabling Ag+ to diffuse into the glass and to precipitate as Ag0. Both species were detected by x-ray absorption spectroscopy (XAS). The precipitated metallic silver particles in Na2O-ZnO-B2O3 (NZB) glass have a mean size of 5.9 nm ± 1.2 nm diameter, which was determined using transmission electron microscopy (TEM). Phase separation in zinc-rich and zinc-poor phases with a mean diameter of 75 nm ± 20 nm occurred in NZB glass after heat treatment. Ion diffusion of the glasses into the silver layer was suggested by EDX-line scans. T2 - 94. Glastechnische Tagung CY - Online meeting DA - 10.05.2021 KW - Silver diffusion KW - Alkali zinc borate glass KW - Metallic silver precipitates KW - Phase separation PY - 2021 AN - OPUS4-52861 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -