TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp T1 - PFAS Sum Parameter and Structural Analysis N2 - Per- and polyfluoroalkyl substances (PFAS) are anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms (see Figure 1) and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, because of the continuous contamination through PFAS containing commercial products, effluents and sewage sludge from WWTPs have been shown to be an important source of PFAS discharge into the aquatic environment. In the last few years, legacy PFAS (≥C4) have been found in various environments, including soil, water and wastewater, and their environmental pathways have been partly described. To get a better overview of the amount of “total PFAS,” sum parameter methods like total oxidizable precursor (TOP) assay and methods based on combustion ion chromatography (CIC) are in development. CIC results in data regarding the sum of absorbable organic fluorine (AOF) or extractable organic fluorine (EOF), which can also quantify other organically bound fluorine compounds such as fluorinated pesticides and pharmaceutical. Additionally, for research purpose several spectroscopical methods like X-ray photoelectron spectroscopy (XPS), fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy, particular induced gamma-ray emission (PIGE) spectroscopy and 19F nuclear magnetic resonance (NMR) spectroscopy are available. Therefore, an overview is given on various analytical techniques for PFAS in environmental samples and their application possibilities discussed for different kind of PFAS compounds T2 - CleanUp 2022 CY - Adelaide, Australia DA - 11.09.2022 KW - PFAS KW - Combustion ion chromatography KW - XANES spectroscopy KW - Soil PY - 2022 AN - OPUS4-55743 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Kratz, S. T1 - Charakterisierung der P-Verfügbarkeit in Düngemitteln durch P-Senken N2 - Recycling-Düngemittel auf Basis von sekundären Ressourcen (Gülle, Gärreste, Klärschlamm, Tiermehl etc.) gewinnen in den letzten Jahren zunehmend an Bedeutung in der Landwirtschaft. Die in den Recycling-Düngemitteln enthaltenen P-Spezies weichen oft stark von denen in konventionell hergestellten Düngemitteln aus Rohphosphat ab, zudem enthalten Recyclingdünger oft mehrere verschiedene P-Formen. Die Pflanzenverfügbarkeit des P in ist ganz wesentlich von der enthaltenen P-Form abhängig. Derzeit gibt es außer zeitaufwendigen und kostspieligen Gefäß- und Feldversuchen keine zufriedenstellende Testmethode zur Analyse der P-Pflanzenverfügbarkeit von unterschiedlichen Recycling P-Düngemitteln. Die im europäischen Düngemittelrecht normierten chemischen Extraktionsmethoden (Wasser, Zitronensäure, Ameisensäure, neutral Ammoniumcitrat etc.) zeigen oftmals keine oder nur sehr geringe Korrelation zu der P-Aufnahme von Pflanzen in Gefäßversuchen mit Recycling-Düngemitteln (Kratz et al. 2010, Steckenmesser et al. 2017, Vogel et al. 2017). Eine grundlegende Schwäche chemischer Extraktionsmethoden liegt darin, dass es sich dabei um statische Methoden handelt, die nicht in der Lage sind, die im System Boden/Düngemittel-Bodenlösung-Pflanze stattfindenden dynamischen Prozesse wie P-Freisetzung und Entzug durch die Pflanzenwurzeln abzubilden. Einen Lösungsansatz bieten hier sog. P-Senken-Methoden. Bereits in den 1950er Jahren wurden erstmals P-Senken zur Analyse des Boden-P angewendet (Chardon et al. 1996). In den darauffolgenden Jahrzehnten wurden verschiedene P-Senken auf der Basis von Eisenoxid-Papier entwickelt (Chardon et al. 1996). Jedoch konnten diese Ansätze auch nur begrenzt zur Bestimmung der P-Pflanzenverfügbarkeit des Boden-P eingesetzt werden. Mitte der 1990er Jahre wurde die DGT (engl. diffusive gradients in thin films) Methode entwickelt (Zhang et al. 1998). Bei der DGT Methode diffundiert P aus der Bodenlösung des angefeuchteten Bodens durch einen Membranfilter und die Diffusionsschicht und wird anschließend an einer Bindungsschicht absorbiert. Durch den Diffusionsgradienten wird das Gleichgewicht in der Bodenlösung permanent gestört, wodurch auch labiles P im Boden gelöst wird. Die stetige Entnahme von P aus der Bodenlösung über die Diffusions-/Bindungsschicht simuliert dabei den Entzug von P durch die Pflanzenwurzel. Die an die Bindungsschicht adsorbierte Menge an P korreliert stark mit der P-Aufnahme von Pflanzen (u.a. Mason et al. 2005, 2013; Menzies et al. 2005, Six et al. 2012). Im Gegensatz zu chemischen Extraktionsmethoden werden bei der DGT Methode Mischungen an Düngemittel und Boden für mehrere Tage inkubiert (Vogel et al. 2017; Duboc et al. 2017), da ansonsten wasserlösliche P-Dünger den DGT Adsorber sättigen und wasserunlösliche P-Dünger unterschätzt werden. Ein bis zwei Wochen Inkubation sind ausreichend, damit sich pflanzenverfügbares P in die Mischungen bildet. In letzter Zeit haben verschiedene Forschungsgruppen gezeigt, dass die DGT Methode auch eine sehr gute Korrelation mit der Pflanzenverfügbarkeit verschiedener Typen von (Recycling-)P-Düngemitteln aufweist (Vogel et al. 2017; Duboc et al. 2017; Foereid 2017; Haarstad and Bavor 2017; Lemming et al. 2017). Bei Gefäßversuchen mit verschiedenen Recycling P-Düngemitteln konnte die DGT Methode den Ertrag bzw. die P-Aufnahme von Mais deutlich besser vorhersagen als herkömmliche chemische Extraktionsmethoden (Vogel et al. 2017; Duboc et al. 2017). Daher kann die DGT Methode im Vorfeld der Zulassung von neuen Düngermitteltypen als zuverlässige und robuste Methode zum Screening von Produktvarianten eines Düngemittelherstellers verwendet werden. Um dieses Messverfahren im Rahmen des Düngemittelrechts als Bewertungsinstrument für die Abschätzung der Pflanzenverfügbarkeit unterschiedlicher Düngemittel zu verwenden, muss es allerdings zunächst standardisiert werden. Zu diesem Zweck bietet sich der Einsatz eines „standardisierten“ Bodens bzw. Bodenrezepts an. Zur Kalibrierung der Methode im jeweiligen Labor könnten auch chemisch definierte P-Verbindungen mit bekannter Löslichkeit/Pflanzenverfügbarkeit als Referenz-substanzen verwendet werden. T2 - Fachgespräch Recycling-Phosphate als Düngemittel für die Landwirtschaft CY - Bonn, Germany DA - 14.02.2018 KW - Düngemittel KW - Sekundärrohstoffe KW - Phosphor KW - DGT KW - P-Senken KW - Extraktionsversuche PY - 2018 AN - OPUS4-44339 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Huang, L. A1 - Sekine, R. A1 - Doolette, A. A1 - Herzel, Hannes A1 - Kugler, Stefan A1 - Hoffmann, Marie A1 - Lombi, E. A1 - Zuin, L. A1 - Wang, D. A1 - Félix, R. A1 - Adam, Christian T1 - Specification of bioavailable nutrients and pollutants in the environment by combining DGT and spectroscopic techniques N2 - Previous research shows that analytical methods based on Diffusive Gradients in Thin films (DGT) provide very good correlations to the amount of bioavailable nutrients and pollutants in the environmental samples. However, these DGT results do not identify which compound of the specific element has the high bioavailability. Using various spectroscopic techniques (infrared, XANES and NMR spectroscopy) to analyze the dried DGT binding layers after deployment could allow us to determine the specific elements or compounds. Nutrients such as phosphorus and nitrogen are often, together with other elements, present as molecules in the environment. These ions are detectable and distinguishable by infrared and NMR spectroscopy, respectively. In addition, XANES spectroscopy allows for the specification of nutrients and pollutants (e.g. chromium) on the DGT binding layer. Furthermore, microspectroscopic techniques make it also possible to analyze compounds on the DGT binding layer with a lateral resolution down to 5 µm2. Therefore, species of elements and compounds of e.g. a spatial soil segment can be mapped and analyzed, providing valuable insight to understand the dynamics of nutrients and pollutants in the environment. Here we will present the advantages and limitations of this novel combination of techniques. T2 - 6th Conference on Diffusive Gradients in Thin Films CY - Vienna, Austria DA - 17.09.2019 KW - Soil P species KW - DGT KW - Infrared spectroscopy PY - 2019 AN - OPUS4-49057 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Adam, Christian A1 - Kugler, Stefan A1 - Herzel, Hannes T1 - Phosphorus recovery from waste streams for fertilizer production N2 - Phosphorus (P) plays an essential role in the global food security. However, the global P reservoirs have a statistic lifetime of about 385 years only. Due to the scarcity of P and the increasing world population an efficient and sustainable recycling management is required. A few biogenic waste materials are high in P contents such as sewage sludge and meat and bone meal. Thus, they are suitable for P recycling and fertilizer production. But besides the high P content sewage sludge is often highly contaminated with organic pollutants and toxic heavy metals which have to be eliminated before agricultural field application. In this presentation we show the potential of sewage sludge as secondary resource for fertilizers. This includes our developments in thermochemical processes for the production of novel P-fertilizers from recycled materials. Furthermore, for these novel P-fertilizers common extraction tests to determine the plant-available P are often unusable. Therefore, we successfully applied the Diffusive gradients in thin-films (DGT) techniques to analyse the plant-availability of P-fertilizers from recycled materials. T2 - Eingeladener Vortrag an der University of South Australia CY - Mawson Lakes, Australia DA - 22.11.2018 KW - Phosphorus recovery KW - Sewage sludge KW - Diffusive Gradients in thin films (DGT) PY - 2018 AN - OPUS4-46764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - PFAS analytics and their relation to PFAS remediation N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of more than 10,000 anionic, cationic, zwitterionic or neutral organofluorine surfactants. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. While liquid chromatography tandem mass spectrometry (LC-MS/MS) is commonly used technique to characterize targeted PFAS in environmental samples, there are more than 10,000 different PFAS known, which have various headgroups and properties. Therefore, several analytical techniques are available to analyse various groups or pools of PFAS or “all” PFAS as a sum parameter. Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Previously, mechanochemical treatment of polychlorinated organic compounds in soils showed an efficient dechlorination. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GC-MS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well es the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - International workshop of CAR-PFAS (Consortium for analysis and remediation of per- and polyfluoroalkyl substances) Japan CY - Tokyo, Japan DA - 17.10.2023 KW - Mechanochemical treatment KW - Per- and Polyfluoroalkyl substances (PFAS) KW - XANES spectroscopy KW - Soil PY - 2023 AN - OPUS4-58609 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Mechanochemical remediation of PFAS in soils – Does it work? N2 - Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. These approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GC-MS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well as the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - Baltic Sea PFAS Network Coffee Session CY - Online meeting DA - 25.08.2023 KW - Mechanochemical treatment KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Remediation KW - X-ray absorption near-edge structure (XANES) spectroscopy PY - 2023 AN - OPUS4-58114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Investigation of per and polyfluoroalkyl substances (PFAS) in soils and groundwater through fluorine K-edge XANES spectroscopy – potential for collaboration N2 - Per- and polyfluoroalkyl substances (PFAS) are a group of anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination. In this presentation the advantages of fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy for various environment samples are shown. T2 - SESAME-Germany Info Day CY - Hamburg, Germany DA - 21.04.2023 KW - Soil KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Synchotron KW - X-ray absorption near-edge structure (XANES) spectroscopy PY - 2023 AN - OPUS4-57365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Huthwelker, T. A1 - Simon, Franz-Georg T1 - Fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy as a novel tool for the characterization of per- and polyfluoroalkyl substances (PFAS) in soils and sludges N2 - Per- and polyfluoroalkyl substances (PFAS) have been used extensively in the past because of their inert chemical character and resistance to degradation by environmental influences. Since the beginning of their commercial use, PFAS have been widely exposed to the environment by application of PFAS in consumer products or as foaming agent in firefighting foams, thus several cases of contaminated soils sites have been reported. Since the number of known PFAS already exceeds 4700, their characterization and direct analysis is challenging given the current available techniques. Here, we introduce the novel fluorine (F) K-edge X-ray absorption near-edge structure (XANES) spectroscopy as a tool to analyze PFAS and inorganic fluorine compounds in contaminated soils and sewage sludges. While F K-edge bulk-XANES spectroscopy provide us information on the overall fluorine bonding in a sample micro X-ray fluorescence (XRF) in combination with F K-edge micro-XANES spectroscopy can also detect minor fluorine compounds and PFAS hotspots in investigated soils and sludges. Additionally, we used the combustion ion chromatography (CIC) to analyze the total amount of all PFAS as a sum parameter (extractable organic fluoride: EOF) in soils and sewage sludges. During combustion in the CIC, the PFAS in the sample get destroyed at temperatures of approx. 1000 °C and converted in inorganic fluorides that subsequently gets quantified by ion chromatography. Thus, for the first time we successfully combined F K-edge XANES spectroscopy and CIC as analytical tools to detect and quantify PFAS contaminants in soils and sewage sludges. T2 - SETAC Europe CY - Online meeting DA - 03.05.2021 KW - Sewage sludge KW - Combustion ion chromatography KW - Soil KW - X-ray absorption near-edge structure (XANES) spectroscopy PY - 2021 AN - OPUS4-52563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Wittwer, Philipp A1 - Roesch, Philipp A1 - Simon, Franz-Georg T1 - Per- and polyfluoroalkyl substances (PFAS) in sewage sludge and wastewater-based fertilizers and future PFAS remediation N2 - Per- and polyfluoroalkyl substances (PFAS) are a group of anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. As a result of the perpetual use of PFAS containing products, effluents and sewage sludge from wastewater treatment plants (WWTPs) have been observed to be an important pathway for PFAS into the environment. In Germany, phosphorus and other nutrients from sewage sludge and wastewater should be recycled in WWTPs of cities with a large population. However, it is not clear if PFAS contamination from wastewater and sewage sludge end up in novel wastewater-based fertilizers. Normally, PFAS are analyzed using PFAS protocols typically with liquid chromatography tandem mass spectrometry (LC-MS/MS) quantification. To get a better overview of the amount of “total PFAS,” we applied sum parameter methods based on combustion ion chromatography (CIC) to screen the PFAS contaminations in various sewage sludge and wastewater-based fertilizers. Furthermore, current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. T2 - Seminar of Ben-Gurion University CY - Midreshet Ben-Gurion, Israel DA - 02.11.2022 KW - PFAS KW - Sewage sludge KW - XANES spectroscopy PY - 2022 AN - OPUS4-56166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Piechotta, Christian A1 - Lisec, Jan A1 - Sommerfeld, Thomas A1 - Kluge, Stephanie A1 - Herzel, Hannes A1 - Simon, Franz-Georg T1 - Per- and Polyfluoroalkyl Substances (PFAS) in Sewage Sludge and Wastewater-based Fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are chemicals which were developed to improve humanity’s quality of life. Due to their high chemical stability and resistance to degradation by heat or acids, PFAS were used in a variety of consumer products. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system resulted in the contamination of effluents and sewage sludge from wastewater treatment plants (WWTPs) (Roesch et al. 2022). Since sewage sludge is often used as fertilizer, its application on agricultural soils has been observed as a significant entry path for PFAS into the environment, specifically in our food chain. In Germany the sewage sludge/biosolid application on agricultural land was banned with the amendment of the German Sewage Sludge Ordinance and by 2029 sewage sludge application will be totally prohibited. However, phosphorus (P) from sewage sludge should still be recycled in WWTPs of cities with a population larger than 50,000 residents. To produce high-quality P-fertilizers for a circular economy, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Due to the strong diversity of industrial PFAS usage it is not clear if a safe application of novel recycled P-fertilizers from WWTPs can be guaranteed. Therefore, we analyzed various sewage sludges and wastewater-based fertilizers. Sewage sludge (SL) samples from various WWTPs in Germany and Switzerland, six sewage sludge ashes (SSA) from Germany, six thermally treated SL and SSA samples with different additives (temperatures: 700-1050 °C), two pyrolyzed SL samples (temperature: 400 °C) and two struvite samples from Germany and Canada were analyzed. The goal was to quantify PFAS in sewage sludges and wastewater-based P-fertilizers with the sum parameter extractable organic fluorine (EOF) by combustion ion chromatography (CIC). The results were compared with data from classical LC-MS/MS target analysis as well as selected samples by HR-MS suspect screening. The EOF values of the SLs mainly range between 154 and 538 µg/kg except for one SL which showed an elevated EOF value of 7209 µg/kg due to high organofluorine contamination. For the SSA samples the EOF values were lower and values between LOQ (approx. 60 µg/kg) and 121 µg/kg could be detected. For the pyrolyzed SLs no EOF values above the LOQ were detected. Moreover, the two wastewater-based struvite fertilizers contain 96 and 112 µg/kg EOF, respectively. In contrast to the EOF values, the sum of PFAS target values were relatively low for all SLs. Additional applied PFAS HR-MS suspect screening aimed to tentatively identify PFAS that could contribute to the hitherto unknown part of the EOF value. The majority of the detected fluorinated compounds are legacy PFAS such as short- and long-chain perfluorocarboxylic acids (PFCA), perfluorosulfonic acids (PFSA), polyfluoroalkyl phosphate esters (PAPs) and perfluorophosphonic acids (PFPA). Moreover, fluorinated pesticides, pharmaceutical as well as aromatic compounds were also identified, which are all included in the EOF parameter. Our research revealed that the current PFAS limit of 100 µg/kg for the sum of PFOS + PFOA in the German Fertilizer Ordinance is no longer up to date. Since the number of known PFAS already exceeds 10,000, the ordinance limit should be updated accordingly. Recent regulations and restrictions on using long-chain PFAS (≥C8) have resulted in a significant shift in the industry towards (ultra-)short-chain alternatives, and other, partly unknown, emerging PFAS. Ultimately, also fluorinated pesticides and pharmaceuticals, which end up as ultrashort PFAS in the WWTPs, have to be considered as possible pollutants in fertilizers from wastewater, too. T2 - Dioxin Konferenz CY - Maastricht, Netherlands DA - 10.09.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge KW - Fertilizer PY - 2023 AN - OPUS4-58345 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Lisec, Jan A1 - Borca, C. A1 - Huthwelker, T. A1 - Simon, Franz-Georg T1 - Combining DGT and combustion ion chromatography (CIC) as screening tool for per- and polyfluoroalkyl substances (PFAS) contamination in wastewater-based fertilizers N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of organofluorine surfactants used in the formulations of thousands of consumer goods. The continuous use of PFAS in household products and the discharge of PFAS from industrial plants into the sewer system have been resulted in contaminated effluents and sewage sludge from wastewater treatment plants (WWTPs) which became an important pathway for PFAS into the environment. Because sewage sludge is often used as fertilizer its application on agricultural soils has been observed as significant input path for PFAS into our food chain. To produce high-quality phosphorus fertilizers for a circular economy from sewage sludge, PFAS and other pollutants (e.g. pesticides and pharmaceuticals) must be separated from sewage sludge. Normally, PFAS are analyzed using PFAS protocols typically with time-consuming extraction steps and LC-MS/MS target quantification. However, for screening of PFAS contaminations in wastewater-based fertilizers also the DGT technique can be used for the PFAS extraction. Afterwards, combustion ion chromatography (CIC) can be applied to analyze the “total” amount of PFAS on the DGT binding layer. The DGT method was less sensitive and only comparable to the extractable organic fluorine (EOF) method values of the fertilizers in samples with >150 µg/kg, because of different diffusion properties for various PFAS, but also kinetic exchange limitations. However, the DGT approach has the advantage that almost no sample preparation is necessary. Moreover, the PFAS adsorption on the DGT binding layer was investigated via surface sensitive spectroscopical methods, such as Fourier-transform infrared (FT-IR) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - DGT Konferenz CY - Paris, France DA - 11.10.2023 KW - Combustion Ion Chromatography KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Sewage sludge PY - 2023 AN - OPUS4-58575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Roesch, Philipp A1 - Wittwer, Philipp A1 - Simon, Franz-Georg T1 - Per- und polyfluorierte Alkylsubstanzen (PFAS) im Klärschlamm - Analytische Methoden und Grenzwerte N2 - Per- und Polyfluoralkylsubstanzen (PFAS) sind eine Gruppe von mehr als 4700 anionischen und kationischen anthrophonen Stoffen, die aufgrund ihrer inerten chemischen Stabilität und ihrer Widerstandsfähigkeit gegen den Abbau durch Hitze oder Säuren in einer Vielzahl von Produkten verwendet werden. Infolge der ständigen Verwendung, vor allem in Feuerlöschschäumen für die Luftfahrt, wurden in Tausenden von Industrie- und Militäranlagen kontaminierte Böden und Grundwasservorkommen gefunden. Aufgrund der ständigen Verwendung von fluorierten Konsumgütern haben sich jedoch auch Abwässer und Klärschlamm aus Kläranlagen als Quelle für die Kontamination der aquatischen Umwelt mit PFAS erwiesen. Infolge der strengeren Vorschriften und Beschränkungen, die in den letzten Jahren für die Verwendung langkettiger (≥C8) PFAS erlassen wurden, findet in der chemischen Industrie eine deutliche Verlagerung hin zur Herstellung kurz- (C4-C7) und ultrakurzkettiger (C1-C3) Alternativen statt. Mit der Novellierung der Klärschlammverordnung im Jahr 2017 hat der deutsche Gesetzgeber die Ausbringung von Klärschlamm auf landwirtschaftlichen Flächen verboten, und bis 2029/2032 wird die Ausbringung von Klärschlamm in der Landwirtschaft vollständig verboten sein. Während die Belastung der Umwelt mit organischen Schadstoffen wie PFAS, Pestiziden und Arzneimitteln nicht mehr erwünscht ist, muss Phosphor (P) aus Klärschlamm weiterhin zur Herstellung hochwertiger P-Dünger für eine Kreislaufwirtschaft genutzt werden. Derzeit können pflanzenverfügbare P-Düngemittel aus Klärschlamm/Abwasser mit verschiedenen Behandlungsmethoden hergestellt werden, darunter Fällung, Auslaugung und thermische Behandlung. Der Verbleib von PFAS bei der Auslaugung, Ausfällung und Behandlung von Klärschlamm und Abwasser ist jedoch noch weitgehend unbekannt. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 14.11.2022 KW - Klärschlamm KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Phosphor KW - Düngemittel PY - 2022 AN - OPUS4-56291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian A1 - Ludwig, S. A1 - Roesch, Philipp A1 - Vigelahn, L. A1 - Wittwer, Philipp A1 - Birke, V. A1 - Simon, Franz-Georg T1 - Mechanochemical Remediation of Per- and Polyfluoroalkyl Substanzes (PFAS) in Soils N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of anionic, cationic, or zwitterionic organofluorine surfactants used in the formulations of thousands of products and consumer goods, including aqueous film-forming foams (AFFF) used to suppress aviation fires in training scenarios, non-stick cookware, fast-food wrappers, water-repellent fabrics, medical equipment. Because PFAS have been extensively used in a variety of AFFF products they can be found in soils from industrial and military installations. Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Previously, mechanochemical treatment of polychlorinated organic compounds in soils showed an efficient dechlorination. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GCMS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well es the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - CleanUp 2022 CY - Adelaide, Australia DA - 11.09.2022 KW - PFAS KW - Mechanochemical treatment KW - XANES spectroscopy PY - 2022 AN - OPUS4-55742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker A1 - Kalinka, Gerhard A1 - Loose, Florian T1 - Carbon fibre composites exemplarily research at BAM N2 - Lightweighting as a cross-cutting technology contributes significantly to achieve the European Green Deal goals. Based on, but not limited to, advanced materials and production technologies, the demand for natural resources and CO2 emmissions are reduced by lightweighting during production, as well as use phase. Therefore, lightweighting is a crucial transformation technology assisting in decoupling economic growth from resource consumption. In this manner, lightweighting contributes significantly as a key technology of relevance for many industrial sectors such as energy, mobility, and infrastructure, towards resource efficiency, climate action and economic strength, as well as a resilient Europe. To strengthen international partnerships, addressing global issues of today at the edge of science with high performance lightweight material based on carbon fibers, an overview about the BAM expertise in carbon fiber reinforced materials is given. T2 - Meeting KCarbon CY - Berlin, Germany DA - 15.06.2023 KW - Lightweighting KW - Carbon Fibers KW - Recycling KW - Push-out Test KW - multi scale testing PY - 2023 AN - OPUS4-58094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Banach, Ulrich A1 - Hübert, Thomas A1 - Bartholmai, Matthias A1 - Noske, Reinhard A1 - Gawlitza, Kornelia A1 - Rurack, Knut T1 - Ammoniakbestimmung mit einem portablen Fluoreszenzsensor N2 - Ammoniakemissionen in die Umwelt erfolgen insbesondere durch die Landwirtschaft (93,6 %), aber auch durch Verbrennungsprozesse in der die Abfallwirtschaft (2,3 %) und den Straßenverkehr (1,8 %). Dieser Stoff ist selbst in geringen Konzentrationen nicht nur eine Geruchsbelästigung, sondern auch eine Substanz mit ökologischer und klimatischer Relevanz. Die Bestimmung von Ammoniak in relevanten Konzentrationen von kleiner 25 μg m-3 erfolgt im Allgemeinen über NH4+ als Analyten, spektralfotometrisch oder mit der Ionenchromatographie nach Überführung in die flüssige Phase. Wegen der niedrigen Konzentrationen an Ammoniak in der Außenluft wird meist eine gesammelte Probe verwendet oder die Bestimmung erfolgt nach einer aktiven, anreichernden Probenahme. Die eigenen Arbeiten sollen dazu beitragen, die Ammoniak-Bestimmung in der Außenluft präziser, sowie schneller und kostengünstiger zu machen. Die BAM prüfte daher kommerzielle elektrochemische und Metalloxid-basierte Sensoren, die für diesen Konzentrationsbereich aber nur bedingt geeignet sind. Deshalb wurden alternativ eigene Entwicklungen zum Nachweis von Ammoniak im Spurenbereich aufgenommen, wobei der Analyt über die Änderung der Fluoreszenz eines BODIPY-Farbstoffs bei 550 nm mittels eines portablen Fluoreszenz-Sensors direkt aus der Gasphase gemessen wird. Zur Kalibrierung von Ammoniak-Sensoren und -Messgeräten steht ein stationäres System basierend auf der Mischung von zertifizierten Prüfgasen aus Druckflaschen mit kalibrierten Massendurchfluss-regler (MFC) zur Verfügung. Darüber hinaus erfolgt eine chemische Analyse der verwendeten Gasgemische mittels eines Massenspektrometers. Für die Kalibrierung und Prüfung von Sensoren und Messgeräten vor Ort wurde ein mobiles Prüfsystem entwickelt. Die Generierung von Ammoniak-haltigen Gasen im Spurenbereich von 0,5 nmol/mol bis 500 nmol/mol erfolgt durch das Permeationsverfahren nach ISO 6145-10. Für die Realisierung der Rückführbarkeit der Ammoniakbestimmung werden von den Nationalen Metrologischen Instituten sowie designierten Instituten Standards bereitgestellt und auch weiterentwickelt. Die primären metrologischen Standards beruhen auf SI-Einheiten und sind die Basis für eine Rückführbarkeit der Sensoren bzw. Analysengeräte. T2 - 5. Fachsymposium „Intelligente Sensorik/Analytik und sichere Sensornetze: Innovative Technologien und neue Anwendungsfelder“ CY - Karlsruhe, Germany DA - 14.11.2018 KW - Ammoniak KW - Sensor KW - Multigassensorik PY - 2018 AN - OPUS4-46926 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Schulenburg, F. A1 - Reuter, M. A1 - Stelter, M. T1 - Optimierung eines pyrometallurgischen Tantal- und Niob- Recyclingprozesses mithilfe von On-Line LIBS N2 - Die Entwicklung von Hochleistungselektronik zu immer kleineren Bauformen ohne Leistungseinbußen ist ohne den Einsatz von Technologiemetallen wie Niob und Tantal heute praktisch nicht mehr realisierbar. Besonders in technischen Geräten wie Smartphones und Tablets sind Tantal- und Niobkondensatoren aufgrund ihrer hohen Leistungsdichten bereits unverzichtbar geworden. Für die nachhaltige Produktion von Elektronik stellt jedoch vor allem das Tantalerz Coltan als sogenanntes „conflict mineral” ein großes Problem dar. Um den Wirtschaftsstandort Europa unabhängiger von Primärrohstoffimporten aus Krisenregionen zu machen, ist die Entwicklung von effizienten Recyclingverfahren heute wichtiger denn je. An der Bundesanstalt für Materialforschung und -prüfung (BAM) findet daher zurzeit die Optimierung eines pyrometallurgischen Industrieprozesses zur Niob- und Tantalrückgewinnung statt, welchem hauptsächlich niedrigkonzentrierte metallurgische Rückstände aus der Tantal- und Niob- bzw. der Zinngewinnung als Einsatzstoffe dienen. Zu diesem Zweck werden im kleintechnischen Lichtbogenofen der BAM (480 kVA, max. Materialdurchsatz ca. 150 kg/h) Versuche mit einem neuen innovativen Messgerät durchgeführt, welches eine On-Line Analyse von Hochtemperaturprozessen ermöglicht. Der eingesetzte Prototyp nutzt das Verfahren der laserinduzierten Plasmaspektroskopie (LIBS), um die chemische Zusammensetzung der Schlackephase noch im Schmelzbad und während eines Schlackeabgusses zu bestimmen. Nach einer Kalibrierung auf das vorliegende Stoffsystem ermöglicht dieser On-Line-LIBS Prototyp der BAM daher eine in-situ Bestimmung der Elementverteilung in der Schmelze. Die hier gewonnenen Daten sollen helfen, die aktuelle Prozessführung zu verbessern und die Tantal- und Niobausbeute noch weiter zu erhöhen. T2 - Jahrestreffen Bremen 2018 der ProcessNet-Fachgruppen Hochtemperaturtechnik (HTT), Abfallbehandlung und Wertstoffrückgewinnung (AuW) CY - Bremen, Germany DA - 06.03.2018 KW - Laser-induced breakdown spectroscopy KW - Tantal KW - On-Line Analyse KW - Recycling KW - Pyrometallurgie PY - 2018 AN - OPUS4-45612 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Schulenburg, F. A1 - Bartmann, U. A1 - Beckmann, T. A1 - Michalik, K. A1 - Reuter, M. A1 - Stelter, M. T1 - Optimisation of a Pyrometallurgical Niobium and Tantalum Recyling Process with on-line-LIBS N2 - Tantalum and niobium are essential for the development of electronics towards a more and more compact design, but without reducing their performance today. Especially in smart phones and tablets, tantalum and niobium capacitors with high charge densities have already become almost indispensable. However, tantalum as a critical raw material is still a problem for the sustainable production of electronics. Due to this fact, the existence of efficient recycling processes especially in Europe is becoming even more important nowadays. The Bundesanstalt für Materialforschung und -prüfung (BAM) is currently working on the optimisation of an existing pyrometallurgical tantalum recycling process. Optimisation of this industrial process is carried out in a small-scale electric arc furnace (480 kVA, capacity approx. 150 kg/h) at BAM using a new and innovative equipment for on-line analysis of high temperature processes. The aim of this project is to identify the best timing for an optimum slag tapping, when the slag is lower than minimum targeted tantalum concentration. Hence, LIBS (Laser induced breakdown spectroscopy) is used to identify the chemical composition of the slag layer and during slag tapping. The on-line-LIBS prototype of BAM enables an in-situ measurement of the element distribution in the melt after calibration on the slag system. First results of this joint research project will be presented including on-line-LIBS-measurements and thermodynamic and kinetic aspects of the process. T2 - European Mineral Processing & Recycling Congress (EMPRC 2018) CY - Essen, Germany DA - 25.06.2018 KW - Laser-induced breakdown spectroscopy KW - Process control KW - Tantalum KW - In-situ analysis KW - Pyrometallurgy PY - 2018 AN - OPUS4-45614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Influence of carbon feeding on a pyrometallurgical Ta and Nb recycling process and the formation of carbides N2 - An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage. T2 - Euopean Metallurgical Conference (EMC) 2019 CY - Düsseldorf, Germany DA - 23.06.2019 KW - Pyrometallurgy KW - Tantalum KW - Carbide formation KW - Reduction process KW - Carbon feeding PY - 2019 AN - OPUS4-48351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taube, Mareike Carolin A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Beckmann, T. A1 - Reuter, M. A1 - Stelter, M. T1 - Tantal-Rückgewinnung aus Zinnschlacken und weiteren Reststoffen N2 - Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment. In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided. Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases. T2 - Berliner Konferenz mineralische Nebenprodukte und Abfälle 2019 CY - Berlin, Germany DA - 13.05.2019 KW - Zinnschlacken KW - Tantal KW - Recycling KW - Pyrometallurgie KW - Lichtbogenofen PY - 2019 AN - OPUS4-48352 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long A1 - Seeger, Stefan A1 - Röllig, Mathias T1 - Minimizing the FFF-3D printer hardware bias on particle emission by adjustment of the set extruder temperature N2 - Fused filament fabrication (FFF) on desktop 3D printers is a material extrusion-based technique often used by educational institutions, small enterprises and private households. Polymeric filaments are melted and extruded through a heated nozzle to form a 3D object in layers. The extrusion temperature is therefore a key parameter for a successful print job, but also one of the main driving factors for the emission of harmful air pollutants, namely ultrafine particles and volatile organic gases, which are formed by thermal stress on the polymeric feedstock. The awareness of potential health risks has increased the number of emission studies in the past years. However, the multiplicity of study designs makes an objective comparison of emission data challenging because printer hardware factors such as the actual extruder temperature (TE) and also feedstockspecific emissions are not considered. We assume that across the market of commercial low- and mid-price FFF printers substantial deviations between actual and set extruder temperatures exist, which have a strong effect on the emissions and hence may bias the findings of exposure studies. In our last publication, we presented a standardized feedstock-specific emission test method and showed that for each investigated feedstock an increase in actual extruder temperature was accompanied by an increase in particle emissions (Tang and Seeger, 2022). Therefore, any systematic discrepancy between set and actual extruder temperature matters. In this study, we used a thermocouple and an infrared camera to measure the actual extruder temperatures at different heights. We found significant under- and overestimation of the actual extruder temperatures by the respective set temperatures in three commercial printers. This caused a broad variation of the measured total numbers of emitted particles (TP), even when the same feedstock was operated. For the determination of TP, we followed the DE-UZ 219 test guideline. In a second round we repeated the tests with all printers adjusted to exactly the same extruder temperatures, i.e., to TE=230°C for ABS and TE=210°C for PLA. All measurements were conducted in a 1 m³ emission test chamber. Particle emissions in the size range between 4 nm and 20 μm were detected. Printing on three different printer models without temperature adjustment resulted for each of the investigated feedstocks in a variation in TP of around two orders of magnitude. After temperature adjustment, this was substantially reduced to approx. one order of magnitude and hence minimizes the bias of printer hardware on the emissions. Our findings suggest that adjustment of the extruder temperature should be mandatory in emission testing standards. It also poses a more accurate benchmark and provides more reliable emission data for evaluation of indoor air quality or for health risk assessments. In addition, a proper temperature setting is in the interest of the user. Some commercial FFF printers may have a higher actual extruder temperature than displayed and unintended overheating may not only impair the print quality but may cause unnecessarily increased exposure to particle emissions. T2 - European Aerosol Conference 2023 CY - Málaga, Spain DA - 03.09.2023 KW - Ultrafine particles KW - Thermal imaging KW - 3D printing KW - Indoor air quality KW - Emission testing PY - 2023 AN - OPUS4-58258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long A1 - Seeger, Stefan T1 - Proposal of a standard test method for the quantification of particulate matter during 3D printing and the systematic ranking of filament materials N2 - The diversity of fused filament fabrication (FFF) filaments continues to grow rapidly as the popularity of FFF-3D desktop printers for the use as home fabrication devices has been greatly increased in the past decade. Potential harmful emissions and associated health risks when operating indoors have induced many emission studies. However, the lack of standardization of measurements impeded an objectifiable comparison of research findings. Therefore, we designed a chamber-based standard method, i.e., the strand printing method (SPM), which provides a standardized printing procedure and quantifies systematically the particle emission released from individual FFF-3D filaments under controlled conditions. Forty-four marketable filament products were tested. The total number of emitted particles (TP) varied by approximately four orders of magnitude (1E9 ≤ TP ≤ 1E13), indicating that origin of polymers, manufacturer-specific additives, and undeclared impurities have a strong influence. Our results suggest that TP characterizes an individual filament product and particle emissions cannot be categorized by the polymer type (e.g., PLA or ABS) alone. The user's choice of a filament product is therefore decisive for the exposure to released particles during operation. Thus, choosing a filament product awarded for low emissions seems to be an easily achievable preemptive measure to prevent health hazards. T2 - 11th International Aerosol Conference CY - Athens, Greece DA - 04.09.2022 KW - Ultrafine particles KW - FFF-3D-Printer KW - Indoor emission KW - Emission test chamber KW - Test method KW - Exposure risk PY - 2022 AN - OPUS4-55666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long A1 - Wilke, Olaf A1 - Seeger, Stefan A1 - Kalus, Sabine A1 - Erdmann, Kerstin T1 - Chemical characterization of ultrafine particles released from 3D printers N2 - Previous studies have shown that desktop 3D printers (Fused Filament Fabrication) emit high numbers of particulate matter, mainly as ultrafine particles (UFP, particle diameter less than 100 nm). However, the chemical composition of emitted particles has been less extensively investigated. In this study, we therefore focused on the chemical composition of particles emitted from 3D printing. The measurements were conducted in a 1 m³ emission test chamber. Emitted particles were sampled by a 13-stage low-pressure cascade impactor onto aluminum foils and then analyzed by TD-GC/MS to identify their organic compounds. Nine commercial filaments made from basic polymers such as Acrylonitrile Butadiene Styrene (ABS), Acrylonitrile Styrene Acrylate (ASA), Polycarbonate (PC), Poly(methyl methacrylate) (PMMA), Nylon, High Performance Polystyrene (HIPS) and a copper-filled Polylactide (PLA) were investigated. The results show that the organic components of the particles are primarily plastic additives such as plasticizer, antioxidant agents, lubricants, UV-absorbers and UV-stabilizers from the filaments. T2 - Healthy Buildings Europe 2021 CY - Online meeting DA - 21.06.2021 KW - UFP KW - FFF-3D-Printer KW - Chemical characterization PY - 2021 AN - OPUS4-52895 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stephan, Ina A1 - Gorbushina, Anna T1 - Pilze als Besiedler von Kulturgut: Wechselwirkungen mit Material erkennen und einschätzen N2 - Mikroskopische Pilze, die sich schnell auf verfügbaren Oberflächen ausbreiten können und die wir (wenn sie sich ansammeln), auch mit bloßem Auge erkennen können, werden Schimmelpilze genannt. Da diese Organismen verschiedene organische Kohlenstoffverbindungen als Nahrung benutzen, werden sie sich bei wachstumfördernden Feuchtigkeitsbedingungen in Bibliothekbeständen schnell ausbreiten können. Im Vortrag werden Haupteigenschaften aller Pilze, sowie auch aktuelle Methoden der Identifizierung dieser Organismen erörtert. Benutzung geeigneter Lebendkulturen als Referenzorganismen geben der Materialprüfung und -forschung eine Möglichkeit des reproduzierbaren Experimentierens mit verschiedenen Materialien und Simulation von Bedingungen im Gebrauch. Vorteile unserer Testverfahren sind: (i) Zeitraffung und Kontrollierbarkeit der Umweltparameter; (ii) Benutzung einer naturnahen Vergesellschaftung; iii) gezielte Variationen der Prüfbedingungen im Labor. Ziel dieser Untersuchungen ist einerseits biogene Schäden an neuen Materialien zu verfolgen und zu modellieren, und damit eine bessere Planungsgrundlage für die Materialentwicklung anzubieten. Andererseits werden mit den Referenzorganismen mikrobiologisch moderne und zeitraffende Techniken angeboten, die neue Behandlungsmethoden oder Pflegeverfahren für die Bestandserhaltung erwarten lassen. T2 - 8. Tag der Bestandserhaltung CY - Freie Universität Berlin, Berlin, Germany DA - 27.09.2018 KW - Kulturgut KW - Pilz KW - Schimmel KW - Bestandserhaltung PY - 2018 AN - OPUS4-46293 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Bretz, S. A1 - Stege, H. A1 - Hahn, Oliver T1 - Non-invasive Identifizierung von Pigmenten in modernen Hinterglasbildern (1905-1955) - Highlights aus der Hinterglasforschung N2 - Im Rahmen des Projektes „Hinterglasmalerei als Technik der Klassischen Moderne von 1905 – 1955“, welches vom Museum Penzberg – Sammlung Campendonk, Penzberg (Gisela Geiger und Diana Oesterle) geleitet wurde und in Zusammenarbeit mit der freischaffenden Restauratorin Simone Bretz, der Bundesanstalt für Materialforschung und -prüfung (BAM) und dem Doerner Institut erfolgte, konnte im Rahmen einer Promotion erstmals ein Konvolut von mehr als 60 Hinterglasbildern mit nicht-invasiven Analysemethoden untersucht werden. Die eingesetzten Verfahren ermöglichten die Identifizierung der Pigmente und eine Klassifizierung der verwendeten Bindemittel. Die materialwissenschaftliche Beschäftigung mit der Hinterglaskunst in ihrer Vielfalt ist ein relativ junges Forschungsfeld. Lange wurde ihr mit Unkenntnis, Missverständnis und sogar Geringschätzung begegnet. Im kunsthistorischen Kontext wurde diese Art der Kaltmalerei zumeist mit dem Begriff der Glasmalerei belegt und nicht als eigenständige Kunstform anerkannt, da in beiden Fällen Glas als Bildträger seinen Einsatz findet. In der Hinterglasmalerei wird die Tafelrückseite mit organisch gebundenen Malfarben verziert und das Werk ausschließlich bei auffallendem Licht betrachtet. Die künstlerische Herausforderung liegt immer in der technischen Notwendigkeit eines umgekehrten Malvorganges: die oberste, durch das Glas sichtbare Schicht muss zuerst auf den Bildträger Glas aufgetragen werden, der optische Hintergrund wird zuletzt aufgebracht. Im Vergleich zum Tafelbild, bei dem die Malerei erst durch den Firnisauftrag Tiefenlicht erhält, entfalten die Farben in der Hinterglasmalerei bereits beim Malen ihre Intensität und erhalten gleichzeitig Schutz durch den gläsernen Bildträger (Bretz et al. 2016). Neben der kunstgeschichtlichen und kunsttechnologischen Bearbeitung der Hinterglasbilder spielten materialwissenschaftliche Untersuchungen an einer Auswahl von 66 Bildern im Rahmen des von der VolkswagenStiftung finanzierten Forschungsprojektes eine zentrale Rolle. Grundsätzlich wurde ein nicht-invasiver Ansatz gewählt, um die fragilen Kunstwerke in-situ zu messen und somit einen Transport zu vermeiden. Die Methodik umfasst neben VIS-Spektrometrie in Reflexion und energiedispersiver Röntgenfluoreszenzanalyse (RFA) auch Infrarotspektroskopie in diffuser Reflexion (DRIFTS) und Raman-Spektroskopie. Mit Hilfe des gewählten methodischen Ansatzes lassen sich sowohl anorganische als auch organische Pigmente identifizieren und die Zusammensetzung von Metallfarben und Folien sowie die Glaszusammensetzung qualitativ bestimmen. Ferner ermöglicht die DRIFT-Spektroskopie eine Klassifizierung der Bindemittel. Die im Rahmen des Forschungsprojektes analysierten Hinterglasbilder können folgendermaßen chronologisch gruppiert werden: 1910-1919 (17 Bilder), 1920-1929 (18 Bilder), 1930-1939 (6 Bilder), 1940-1949 (7 Bilder), 1950-1955 (13 Bilder) und >1955 (5 Bilder). Die Auswertung der Ergebnisse ermöglicht grundsätzliche Aussagen über die verwendeten Malmaterialien in Hinterglasbildern in der ersten Hälfte des 20. Jahrhunderts und zeigt Änderungen der verwendeten Pigmente im zeitlichen Kontext auf. Während der ersten Hälfte des 20. Jahrhunderts kamen viele neue Pigmente und Malmaterialien auf den Markt, wobei speziell die synthetischen organischen Pigmente (SOP) zu nennen sind. Eine Vielzahl an SOP konnte in Hinterglasbildern aus allen Zeitgruppen identifiziert werden, wobei hier vor allem Farblacke aus synthetischem Alizarin (PR83), Vertreter der roten und orangen β-Naphthol Pigmente [(z.B. PR3, PR4, PO5 (in Nächtliche Fahrt, 1921 von L. Hildebrandt nachgewiesen)], die blauen und grünen Kupferphthalocyanine [z.B. PG7, PB15 (taucht ab 1949 in Hinterglasbildern auf)] und einige gelbe Azopigmente [z.B. PY1, PY3, PY12 (in Geneigter Mädchenkopf, 1941 von Oskar Schlemmer gefunden)] aufzuführen sind (Steger et al. 2018; Steger et al. 2019a). Einige seltene SOP der Triarylcarboniumgruppe konnten ebenso nachgewiesen werden. Darunter fallen neben der Identifizierung von PR81 (Ohne Titel, 1954, M. Uhlenhuth) auch die erstmaligen Nachweise von PV2 (Hahn, um 1945, L.-G. Buchheim) und PG1 (Exzellente und einmalige Dressuren, 1945/46, L.-G. Buchheim) in Kunstwerken überhaupt (Steger et al. 2018; Steger et al. 2019a). Ferner konnten mit PB52 aus der Gruppe der Anthrachinone und PR60 aus der Gruppe der verlackten Naphthalin-Sulfonsäure-Pigmente weitere seltene SOP in den Bildern Rudern (um 1912) beziehungsweise Apokalyptischer Reiter II (1914) von Wassily Kandinsky nachgewiesen werden (Steger et al. 2019b). Neben den Entwicklungen der SOP können auch eindeutige Trends in den anorganischen Pigmenten veranschaulicht werden. Seltene anorganische Pigmente wie zum Beispiel Strontiumweiß (SrSO4) in der Kreuzabnahme (1914/15) von Carlo Mense (Steger et al. 2019c) wurden identifiziert. Neu entwickelte anorganische Pigmente wie zum Beispiel Cadmiumrot (Cd(S,Se); ab 1928 in 11 Hinterglasbildern nachgewiesen) oder Titanweiß (TiO2; Anatas kommt ab 1922 vor, Rutil konnte nur in Kissen der Träume, 1976 von Werner Schriefers identifiziert werden) tauchen in einigen Hinterglasbildern auf. Schweinfurter Grün (3Cu(AsO2)2·Cu(CH3COO)2) oder Strontiumgelb (SrCrO4) wurden in einigen Bildern bis etwa um 1925 gefunden; diese Pigmente konnten dagegen in späteren Bildern nicht mehr nachgewiesen werden. Als Beispiel sind hier vier frühe Hinterglasbilder (1909–1914) von Wassily Kandinsky zu nennen, wobei Strontiumgelb in vielen Bildpartien zu finden war (Steger et al. 2019b). Publizierte materialwissenschaftliche Ergebnisse von Kandinskys Leinwandgemälden aus späteren Werksperioden zeigen, dass Strontiumgelb zu dieser Zeit vollkommen aus seiner Palette verschwunden ist und vor allem durch ein anderes Gelbpigment, nämlich Cadmiumgelb, ersetzt wurde (McMillan et al. 2013). Eine materialtechnische Besonderheit in der Hinterglaskunst ist die Verwendung von Metallfolien und Metalleffektpigmenten. Metallfolien aus Silber, Zinn, Aluminium oder Messing wurden vielfach als künstlerisches Element in die Komposition integriert, wobei sie als finale Schicht auf, die bereits gestaltete, leicht transparente Malerei geklebt wurden. Durch die Betrachtung im auffallenden Licht erzeugten die Folien bemerkenswerte Glitzereffekte. Zinn- und Aluminiumfolien wurden zum Beispiel in Rudern (um 1912, W. Kandinsky) nachgewiesen, während Messingfolien häufig in Bildern von L.-G. Buchheim gefunden wurden. Die Zinnfolien wurden im 19. und frühen 20. Jahrhundert für Verpackungszwecke (z.B. Zigaretten, Schokolade) verwendet. Aluminiumfolie wurde erst ab 1910 industriell in der Schweiz hergestellt und zu Beginn vor allem für Schokoladenverpackungen eingesetzt (Skrabec 2016). Die frühe Verwendung solche Folien in Hinterglasbildern (z.B. Rudern, um 1912) zeigen eine rasche Verbreitung dieses Materials bei den Künstlern an. Unter Metalleffektpigmenten versteht man feingemahlene Pulver aus Metall (z.B. Zinn, Nickel, Kupfer) und Legierungen (z.B. Messing, Neusilber) mit unterschiedlichen Tönungen, welche bei seitlichem Lichteinfall auf Hinterglasbildern ein merkbares Funkeln erzeugen. Solche Metalleffektpigmente wurden vielfach bei Werken von Heinrich Campendonk nachgewiesen (Geiger und Bretz 2017) und konnten in allen chronologischen Gruppen gefunden werden. Grundsätzlich ermöglichen die Ergebnisse ein besseres Verständnis für die Technik der Hinterglasmalerei und helfen insbesondere, diese eigenständige Kunst im Hinblick auf die „klassische“ Tafel- bzw. Leinwandmalerei abzugrenzen. So zeigen Vergleiche mit Gemälden auf Leinwand von Wassily Kandinsky deutliche Unterschiede in den verwendeten Farbmitteln für beide Techniken. Die Anzahl von 66 gemessenen Hinterglasbildern von 39 Künstlern erscheint im Kontext von über 1200 Arbeiten, welche im Rahmen des Projektes lokalisiert werden konnten, gering. Allerdings können die durchgeführten Untersuchungen als Startpunkt für zukünftige Projekte in diesem Forschungsfeld, beispielsweise für einzelne Werkkomplexe verstanden werden. Die Forschungsergebnisse werden auf die Webseite www.hinterglas-klassischemoderne.de eingestellt. Im Sommer 2020 präsentiert das Museum Penzberg – Sammlung Campendonk Hinterglasbilder von 1910 bis 1960 als Abschlussausstellung des Forschungsprojektes. Die Ausstellung wird von einem ausführlichen Katalog über die fächerübergreifende Forschung begleitet. Für Herbst 2020 ist ein Hinterglas-Symposium an der Bundesanstalt für Materialforschung und -prüfung (BAM) Berlin im Rahmen eines N.i.Ke. Workshops geplant. T2 - Jahrestagung Archäometrie und Denkmalpflege 2019 CY - Vienna, Austria DA - 11.09.2019 KW - Reverse glass painting KW - Raman spectroscopy KW - DRIFTS PY - 2019 AN - OPUS4-49259 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon T1 - Spectroscopic analysis of colourants and binders of Chinese reverse glass paintings tracing a cultural dialogue N2 - Scientific analysis based on spectroscopic methods provide essential information on the composition of colourants and binders in paintings. These results can be set in a historical context and help to confirm art historical interpretations. Proofs of certain pigments can be used for dating purposes and may reveal if the artist used not only local but also imported materials. A pilot study of two Chinese reverse glass paintings from the late 19th (Yingying and Hongniang) and early 20th centuries (The Archer) was performed using a multi-analytical approach including X-ray fluorescence (XRF), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and Raman spectroscopy. This approach allowed the identification of the pigments and the classification of the binding media. The results reveal a combined use of traditional Chinese and imported European materials. Several pigments like cinnabar, lead white, orpiment, carbon black and copper-arsenic green (probably emerald green) were found in both paintings; red lead, artificial ultramarine blue, Prussian blue and ochre appear in at least one of the paintings. The proof of limewash (calcite and small amounts of portlandite) as a backing layer in “Yingying and Hongniang” indicates that clamshell white was also used for reverse glass paintings. Drying oil was classified as a binding media in most areas of both paintings. However, the orange background of The Archer yielded prominent bands of both proteinaceous and fatty binder. T2 - China and the West Reconsidering Chinese Reverse Glass Painting CY - Romont, Switzerland DA - 14.02.2020 KW - Reverse glass painting KW - DRIFTS KW - Raman spectroscopy PY - 2020 AN - OPUS4-50445 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Hahn, Oliver A1 - Stege, H. A1 - Oesterle, D. A1 - Bretz, S. A1 - Geiger, G. T1 - Disclosing a new aspect in modern European art: multidisciplinary analysis of modern reverse paintings on glass (1905-1955) N2 - The technique of painting on the reverse side of a glass panel was rediscovered by German artists at the beginning of the 20th century. They appreciated the impressive gloss, luminosity, and depth of colours in this genre. Compared to stained glass, the distinctive properties of this technique are: (1) the paint is applied “cold”, hence, it doesn’t involve a firing step, (2) reverse paintings on glass are framed and always viewed in reflected light and (3) the reverse paint stratigraphy is different from canvas paintings, starting with the front most layer and ending with the backing layer. In 1908 several artists, including Gabriele Münter, Wassily Kandinsky, Heinrich Campendonk, August Macke and Franz Marc of the “Der Blaue Reiter” (the Blue Rider) collective took an interest in this technique and started to share their interest with other colleagues in Europe. Our pioneering project is tracing this transfer of knowledge by a multidisciplinary approach in terms of art history, paint technology and material science. More than 100 artists and >1000 reverse paintings on glass were identified during the project. This high number of objects clearly points out that this technique was by far more important for modern art than previously assumed. In-situ, non-invasive measurements (XRF, Raman, VIS, DRIFTS) on a well-considered selection of 67 paintings reveal the broad palette of colorants ranging from traditional to experimental. Special attention is paid to the impact of synthetic organic pigments (SOP) in artists palette. Demonstrative examples by W. Kandinsky, L. G. Buchheim and F. Jespers are used to discuss analytical challenges and highlights. T2 - Art & Archaeology 2018 CY - Jerusalem, Israel DA - 09.12.2018 KW - Reverse glass painting KW - Spectroscopy KW - In-situ analysis PY - 2018 AN - OPUS4-47042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon A1 - Stege, Heike A1 - Hahn, Oliver T1 - In-situ spectroscopic analysis of modern reverse paintings on glass (1905-1955) N2 - The technique of painting on the reverse side of a glass panel was rediscovered by German artists at the beginning of the 20th century. In contrast to other paint techniques (e.g. panel and mural painting), the paint layers are applied in reverse succession starting with the foremost paint layer and ending with the primer (backmost layer). The paintings are viewed in reflected light, thus revealing an impressive gloss, luminosity and depth of colour. The artist group “Der Blaue Reiter” (the Blue Rider) around W. Kandinsky and F. Marc got in touch with this technique in the summers of 1908 and 1909 and spread their knowledge in different regions. Our pioneering project is tracing this transfer of knowledge by a multidisciplinary approach in terms of art history, painting technology and material science. More than 100 artists and >1000 reverse paintings on glass (1905-1955) were identified during the project. This numbers clearly point out that this technique was by far more important for modern art than previously assumed. In-situ, non-invasive measurements (XRF, Raman, VIS, DRIFTS) on a well-considered selection of 67 paintings reveal the broad palette of colorants ranging from traditional to experimental materials. Special attention is paid on artists who are strongly connected to Berlin. Demonstrative examples by W. Dexel, G. Muche and L. Hildebrandt are used to discuss analytical challenges and highlights. T2 - Young Researchers in Archaeometry (YRA) 2nd Workshop CY - Berlin, Germany DA - 23.09.2018 KW - Raman spectroscopy KW - DRIFTS KW - Reverse glass painting PY - 2018 AN - OPUS4-46066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz A1 - Karafiludis, Stephanos A1 - Pimentel, C. A1 - Montes Hernandez, G A1 - Kochovski, Z A1 - Bienert, Ralf A1 - Weimann, Karin A1 - Emmerling, Franziska A1 - Scoppola, E A1 - Van Driessche, A T1 - Solution-driven processing of calcium sulfate: the mechanism of the reversible transformation of gypsum to bassanite in brines N2 - Calcium sulfate hemihydrate (CaSO4ᐧ0.5H2O), also known as bassanite, has been used as a precursor to produce gypsum (dihydrate, CaSO4ᐧ2H2O) for various construction and decorative purposes since prehistoric times. The main route to obtain hemihydrate is a thermal treatment of gypsum at temperatures typically between 150 °C and 200 °C to remove some of the structural water. In this contribution, we introduce (Fig. 1) a more efficient and sustainable method (T < 100 °C) that enables the direct, rapid, and reversibly conversion of gypsum to bassanite using reusable high salinity aqueous solutions (brines with c[NaCl] > 4 M). The optimum conditions for the efficientproduction of bassanite in a short time (< 5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the typical behaviour of the bassanite phase in low salt environments. Traditionally, hemihydrate is obtained through a solid state thermal treatment because bassanite is considered to be metastable with respect to gypsum and anhydrite in aqueous solutions, and therefore gypsum-to-bassanite conversion should not occur in water. Its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures is inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline structure for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios. T2 - Granada Münster Discussion Meeting GMDM 10 CY - Münster, Germany DA - 29.11.2023 KW - Gypsum KW - Bassanite KW - Calcium sulfate KW - Recycling KW - Scattering PY - 2024 AN - OPUS4-59162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stahl, E. A1 - Meiller, M. A1 - Dombinov, V. A1 - Herzel, Hannes T1 - ASHES-nutrient recycling from the thermo-chemical processing of waste bagasse and straw - Clips from a German-Brazilian collaborative research project N2 - The challenge of the project ASHES is focused on the recycling of nutrients from residues of thermochemical processing of by-products of sugar cane industry (bagasse/straw) in Brazil to increase the energy efficiency of thermal conversion and to enable the recycling of process ashes as fertilisers. Dry lignocellulosic biomass (straw, bagasse) are combusted, gasified and subsequently combined with post-thermochemical treatment in the AshDec process to increase the plant availability of phosphorus. Different fertilizer formulations are granulated/pelletized and tested regarding their storage/handling characteristics. T2 - Biomass Ash 2018 CY - Kopenhagen, Denmark DA - 06.06.2018 KW - Bagasse KW - Nutrient KW - Recycling PY - 2018 AN - OPUS4-45652 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Souza Filho, I. A1 - Adam, Christian T1 - Fundamentals of the hydrogen plasma reduction of iron ores N2 - Hydrogen plasma treatment of iron ores or iron oxide containing wastes can be an efficient option to produce green iron e.g. for steel production. This way iron oxide is reduced to metallic iron in the liquid form by the highly reactive species that are formed in a hydrogen plasma. Hydrogen plasma can be used at the same time to remove undesired gangue elements. The presentation shows the experimental setup, shows first results of iron ore reduction by hydrogen plasma and gives an outlook for industrial application of the technology. T2 - European Academic Symposium on EAF steelmaking (EASES 2023) CY - Oulu, Finland DA - 05.06.2023 KW - Hydrogen KW - Plasma KW - Reduction PY - 2023 AN - OPUS4-57626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobisch, Lydia-Yasmin A1 - Schreiber, Frank T1 - Biocide resistance evolution of corrosion causing sulfate reducing bacteria N2 - SRB are environmentally and industrially important microorganisms. The disadvantage of their metabolic activity (e.g. sulfate reduction) results in the formation of toxic sulfide that leads to microbial influenced corrosion. SRB have been responsible for biocorrosion of ferrous metal. One of mitigation strategy is the use of biocides. However, it has been shown that various bacteria develop antimicrobial resistance due to excessive use of biocides. Thus, a deeper understanding of the evolution of biocide resistance of SRB is necessary. Three commonly used biocides, THPS, BAC, and GLUT were applied to investigate the susceptibility of Desulfovibrio alaskensis G20.The minimum inhibitory and bactericidal concentration and the killing kinetics of the three biocides was determined. These results will be used to conduct evolution experiments to determine the evolution of resistance towards biocides of SRBs. The outcome of this work can be helpful to improve the management of MIC treatments. T2 - Panel, Pitch & Popcorn by EUROMIC CY - Online meeting DA - 21.06.2021 KW - Biocide KW - Evolution KW - Mircobially influcenced corrosion KW - Sulfate reducing bacteria PY - 2021 AN - OPUS4-56940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Scholz, Philipp T1 - Einstufung von Aschen und Schlacken aus der Abfallverbrennung im Hinblick auf die weitere Verwertung – Handlungsempfehlungen N2 - Die Einstufung von Hausmüllverbrennungsasche (HMVA) als gefährlich oder nicht gefährlich nach der Gefahreneigenschaft HP14 (ökotoxisch) ist nach wie vor umstritten, da es noch keine allgemein anerkannten Methoden zur Bewertung gibt. Wenn die Berechnungsregeln angewendet werden sollen angewendet werden sollen, sind Kenntnisse über die chemische Zusammensetzung von HMVA erforderlich. Informationen über die chemische Zusammensetzung von HMVA können mit einem Ansatz gewonnen werden, der auf der Gruppierung von Substanzen. Für HMVA können vier Stoffgruppen definiert werden: 1. elementare und legierte Metalle, 2. leicht wasserlösliche Stoffe, 3. schwer lösliche Stoffe und 4. Stoffe mit starken chemischen Bindungen. Elementares und legiertes Cu und Zn sind in der HMVA vorhanden und werden in der Regel als Nichteisenmetallfraktion zurückgewonnen, zumindest die größeren Partikel. Zn-Partikel, die kleiner als 1 mm sind, werden als H410 eingestuft, feine Partikel von Cu nur als H411. Die wasserlösliche Fraktion kann mit Standardauslaugungsmethoden quantifiziert werden Auslaugungsmethoden quantifiziert werden, z. B. bei einem Flüssigkeits-Feststoff-Verhältnis (L/S) von 2 oder 10 l/kg. Sowohl die Sulfate von Zn als auch von Cu gehören zu dieser Gruppe. In einer neueren Veröffentlichung wurde gezeigt, dass bei den oben genannten Metalle die ausgelaugte Menge weit unter dem Grenzwert von 1.000 mg/kg liegt, selbst wenn stöchiometrische Faktoren angewendet werden. Stoffgruppe 3 sind potenzielle H410-Stoffe. Dabei handelt es sich um Carbonate, Hydroxide und Oxide der betreffenden Elemente, die löslich sind in schwachen organischen Säuren wie Essigsäure löslich sind. Die Worst-Case-Stoffe der Gruppe 3, d. h. die Verbindungen mit den höchsten stöchiometrischen Faktoren, sind CuCO3xCu(OH)2 und ZnO. Stoffe mit starken chemischen Bindungen wie Silikate oder Sulfide sind nur löslich in starken Säuren (z.B. Königswasser) löslich und haben keinen Ökotoxizitäts-Gefahrencode. Das Mobilisierungsverhalten der relevanten Schwermetalle und damit der Gruppe der schwer schwerlöslichen Verbindungen kann mit der 4-stufigen sequenziellen Extraktion untersucht werden. Für die HP14 Einstufung könnte auch eine einstufige Extraktion ausreichend sein. Nur die Elemente Zn und Cu sind für die HP14-Einstufung der HMVA von Bedeutung, da die Feststoffgehalte aller anderen Schwermetalle unterhalb des Feststoffgehalte aller anderen Schwermetalle unter der Cut-Off-Grenze von 0,1 % liegen, selbst wenn man sie in chemischen Verbindungen mit stöchiometrischen Faktoren. Im Ergebnis wurde gezeigt, dass HMVA in der Regel als nicht gefährlich einzustufen ist. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2024 KW - Rostasche KW - Ökotoxizität KW - Sequenzielle Extraktion PY - 2024 AN - OPUS4-60284 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Vogel, Christian A1 - Leube, Peter T1 - Detektion, Quantifizierung und Entfernung von insbesondere ultrakurzkettigen PFAS in Grundwasser N2 - Da PFAS in großem Umfang in einer Vielzahl von Produkten verwendet wurde, sind sie im Grundwasser in der Nähe vieler industrieller und militärischer Anlagen weltweit zu finden. Darüber hinaus führten neue Vorschriften und Beschränkungen für die Verwendung von langkettigen PFAS zu einer vermehrten Produktion kurzkettiger Alternativen. Ultrakurzkettige PFAS (≥C3) können natürliche und anthropogene Barrieren durchdringen und schließlich in Trinkwasserquellen gelangen. Zudem entfernen die meisten gängigen Trinkwasser-aufbereitungsverfahren die ultrakurzkettigen PFAS nicht ausreichend. Im Kooperationsprojekt DEFEAT-PFAS wird daher das Ziel verfolgt, Wissenslücken über Nachweis, Quantifizierung und Entfernung von kurz- (C4-C7) und ultrakurzkettige (C1-C3) PFAS, in kontaminiertem Grundwasser zu schließen. Die israelischen und deutschen Projektpartner entwickeln dafür analytische Methoden and selektive Passivsammler, um das zeitliche Profil von PFAS-Spezies im Grundwasser zu erfassen und überwachen. Darüber hinaus ein zweistufiges Verfahren entwickelt, welches darauf ausgelegt ist, die relativ niedrigen PFAS-Konzentrationen im Grundwasser durch neuartige Membranverfahren, Umkehrosmose im Batchbetrieb mit geschlossenem Kreislauf sowie Verbund-Nanofiltrationsmembranen, zu konzentrieren. Anschließend werden die PFAS angereicherten Konzentrate mittels Koagulation behandelt und das verbleibende PFAS an kohlenstoffhaltigen Nanomaterialien adsorbiert. T2 - Workshop des Netzwerks Perflusan CY - Karlsruhe, Germany DA - 18.06.2024 KW - Grundwasser KW - Per- und Polyfluoroierte Alkylsubstanzen (PFAS) PY - 2024 AN - OPUS4-60334 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Product testing and performance N2 - Geosynthetic materials are applied in measures for coastal protection. Weathering or any damage of constructions, as shown by a field study in Kaliningrad Oblast (Russia), could lead to the littering of the beach or the sea (marine littering) and the discharge of possibly harmful additives into the marine environment. The ageing behavior of a widely used geotextile made of polypropylene was studied by artificial accelerated ageing in water-filled autoclaves at temperatures of 30 to 80° C and pressures of 10 to 50 bar. Tensile strength tests were used to evaluate the progress of ageing, concluding that temperature rather than pressure was the main factor influencing the ageing of geotextiles. Using a modified Arrhenius equation, it was possible to calculate the half-life for the loss of 50% of the strain, which corresponds to approximately 330 years. T2 - EuroGeo-7, Session Geosynthetics, Sustainability and Current Industry Challenges CY - Warschau, Poland DA - 04.09.2022 KW - Geosynthetics KW - Ageing KW - Autoclave tests PY - 2022 AN - OPUS4-55671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Wiedergewinnung von Rohstoffen aus Abfall N2 - Der Vortrag führt aus, wie Sekundärrohstoffe aus Abfällen gewonnen werden. Dabei wird auch auf die Umweltverträglichkeit der Produkte eingegangen. T2 - Weiterbildung für Efb-Sachverständige, Mitarbeiter von Entsorgungsunternehmen und Umweltbehörden CY - Berlin, Germany DA - 04.01.2018 KW - Sekundärrohstoffe KW - Stoffstromanalyse KW - Kreislaufwirtschaft PY - 2018 AN - OPUS4-44941 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Rückgewinnung von Aluminium aus Abfällen N2 - Abtrennung von Nichteisenmetallen aus Müllverbrennungsaschen T2 - IFAT, Messe für Wasser-, Abwasser-, Abfall- und Rohstoffwirtschaft CY - München, Germany DA - 16.05.2018 KW - Rostasche KW - Kumulierter Energieaufwand KW - Sekundärrohstoffe PY - 2018 AN - OPUS4-44939 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Scholz, Philipp A1 - Gleis, Markus T1 - Aschen und Schlacken aus der Abfallverbrennung; Gefährlich oder nicht? N2 - In Deutschland fallen aktuell pro Jahr über 5 Mio. Tonnen Hausmüllverbrennungs-aschen (HMVA) an. Eine Verwertung dieser Aschen und Schlacken ist in Deutschland möglich und findet überwiegend im Deponiebau statt. Für die Verwertung sind in der Ersatzbaustoffverordnung Eluatgrenzwerte für Schwermetalle und einige andere Parameter vorgesehen. Der Umgang mit HMVA könnte durch eine Einstufung als gefährlicher Abfall erschwert werden. Maßgeblich für die Einstufung eines Abfalls als gefährlich oder ungefährlich sind die gefahrenrelevanten Eigenschaften HP 1 bis HP 15 nach Anhang III der Richtlinie 2008/98/EG über Abfälle mit dort festgelegten Konzentrationsgrenzen. Für HMVA ist im Wesentlichen nur der Parameter HP 14 (Ökotoxizität) von Bedeutung. Dafür sind entscheidend die Gehalte an chemischen Verbindungen mit den Gefahrenhinweiscodes (hazard statement code, HSC) H400, H410, H411, H412 und H413. Eine detaillierte Diskussion zu den übrigen Gefahreneigenschaften bei HMVA findet sich in der Literatur. Die Einstufung als gefährlicher Abfall erfolgt nach festgelegten Rechenregeln. Die BAM bearbeitet ein durch das UBA gefördertes Forschungsprojekt zur Erfassung und Bewertung von Analysedaten zu Aschen und Schlacken aus Abfallverbrennungsanlagen. Die Ergebnisse des Vorhabens sollen bei der Weiterentwicklung des vorhandenen Konzeptes für eine bundeseinheitlichen Untersuchung und abfallrechtlichen Einordnung von Aschen und Schlacken aus deutschen Abfallverbrennungsanlagen unterstützend herangezogen werden. Im Vortrag werden Verfahren zur quantitativen Bestimmung der einstufungsrelevanten Verbindungen vorgestellt: 1.) der Praxisleitfaden von ITAD und IGAM, 2.) Methode basierend auf der Bioverfügbarkeit und 3.) Methode basierend auf Speziierungsanalyse. T2 - Jahrestreffen 2023 der DECHEMA-Fachgruppen AuW und TRO CY - Dresden, Germany DA - 06.03.2023 KW - Rostasche KW - Speziierungsanalyse KW - Abfallbehandlung PY - 2023 AN - OPUS4-57346 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Pienkoß, Fabian T1 - Das ERA-MIN 2 Projekt BASH-TREAT N2 - Im Rahmen des Projekts wurde 1.) eine vollständige Bewertung des Stands der Technik in der EU bei der Behandlung von Rostasche vorgenommen und 2.) eine Optimierung der Nutzung der Feinfraktion in Labor- und Feldmaßstab untersucht. Das Konsortium bestand aus zwei Universitäten aus Deutschland und Italien, der BAM als Forschungseinrichtung des Bundes und zwei Industriepartnern aus Deutschland und Schweden mit unterschiedlichen und spezifischen Fachkompetenzen. Im Vortrag werden die Ergebnisse des weitgehend abgeschlossenen Projekts BASH-TREAT vorgestellt. T2 - Jahrestreffen der ProcessNet-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung, Energieverfahrenstechnik, Gasreinigung, Hochtemperaturtechnik, Rohstoffe CY - Bamberg, Germany DA - 30.03.2022 KW - Rostasche KW - Thermische Abfallbehandlung KW - Nassaufbereitung PY - 2022 AN - OPUS4-54589 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Secondary building materials in a circular economy N2 - Half of the global material consumption is mineral material. The circularity is still low so that enhanced use of secondary building material is required to close loops. Three different secondary building materials are discussed based on exemplary research results: construction and demolition waste (C&D waste), soil-like material and incineration bottom ash (IBA). Focus was laid on the environmental compatibility of the materials examined mainly by standardized leaching tests. C&D waste was investigated after a wet treatment using a jigging machine, soil-like material and IBA were characterized with respect to their material composition. The environmental compatibility in particular was studied using standard leaching tests (batch tests and column tests). It was concluded that soil-like material can mostly be utilized even when the precautionary limit values set are exceeded by a factor of less than 2. For C&D waste the fine fraction below 2 mm and the content of brick material is problematic. IBA fulfills quality level HMVA-2 following German regulation. Higher quality levels of utilization might be achievable with better treatment technologies. T2 - 15th International Conference on Ecomaterials (ICEM15) CY - Iki, Japan DA - 26.11.2023 KW - Secondary building materials KW - Incineration bottom ash KW - Construction and demolition waste KW - Soil-like material PY - 2023 AN - OPUS4-59186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - EI-GEO (S&T CALL 2017), Environmental impact of geosynthetics in aquatic systems N2 - 2021 marks the 10th anniversary of the first ERA.Net RUS joint call for European-Russian STI cooperation projects. Pooling the resources of more than 20 European and Russian funding agencies, more than 150 projects were funded with an estimated budget of about € 60 million. Being even larger than many thematic ERA.NETs, the ERA.Net RUS Plus has been the biggest and most successful regional ERA.NET so far. Indicating a strong demand for scientific cooperation, the smaller-scale projects funded within the ERA.Net RUS (Plus) calls perfectly complement Russian participation in the EU Framework Programmes. Not least of all, the ERA-Net RUS calls are examples of successful collaboration at a time when cooperation in other fields is complicated by the politically challenging situation. These calls contributed to keeping the communication channels open. Against this background a dedicated event in late 2021 highlighted what has been achieved within the first decade of the initiative. The project EI-GEO coordinated by BAM was selected as best practice project. The presentation displays the main results of the project and discusses the key success factors. T2 - ERA.Net RUS: Celebrating ten years of multilateral European-Russian Research and Innovation cooperation CY - Online meeting DA - 09.12.2021 KW - Geosynthetics KW - Coastal protection KW - European research area PY - 2021 AN - OPUS4-53965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Wiedergewinnung von Rohstoffen aus Abfall N2 - Antimon (Sb) wird in Industrieprodukten hauptsächlich als Flammschutzmittel in Kunststoff verwendet. Aufgrund solcher Zusätze in Kunststoffen landet etwa die Hälfte von Sb am Ende der Lebensdauer in der Verbrennung fester Siedlungsabfälle und folglich in relevanten Mengen in der erzeugten Bodenasche. Bei Kontakt mit Wasser ist die anfängliche Auslaugbarkeit gering, da Antimonat mit Ca2+ schwerlösliche Verbindungen bilden. Nach der Carnonatisierung der Verbrennungsasche (IBA) während der fortschreitenden Alterung nimmt der pH-Wert in den Sickerwasser ab. Mit abnehmender Ca-Konzentration im Eluat ändert sich das Lösungsgleichgewicht und Antimonate lösen sich auf. In Deutschland ist beabsichtigt, Sb in IBA mit der geplanten Umsetzung der sogenannten Mantelverordnung (MantelVO, die Bestimmungen zur Verwertung von Mineralabfällen enthält) in naher Zukunft zu regulieren. Die im Entwurf festgelegten Grenzwerte können für IBA kritisch sein und stellen daher ein Risiko für die Verwendung der Mineralfraktion von IBA in den gut etablierten Recyclingwegen dar. T2 - Weiterbildung für Efb-Sachverständige, Mitarbeiter von Entsorgungsunternehmen und Umweltbehörden (GUT GmbH) CY - Online Meeting DA - 07.01.2021 KW - Rostasche KW - Antimon KW - Auslaugverfahren PY - 2021 AN - OPUS4-52438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Beschleunigte Alterung von Geotextilien zur Ermittlung von Materialeigenschaften N2 - Geokunststoffe werden im Wasserbau häufig eingesetzt, beispielsweise bei Maßnahmen für den Küstenschutz oder in Ballastschichten für Windenergieanlagen. Eine zunehmende Anwendung von Geokunststoffen wird aufgrund der Ausweitung der Offshore-Windenergieerzeugung und des Schutzes auf steigende Wasserspiegel und extremere Wetterbedingungen infolge des Klimawandels beobachtet. Die Anwendung von Geokunststoffen in Wasserbauprojekten bietet zwar verschiedene wirtschaftliche und technische Vorteile, wurde jedoch kürzlich in Frage gestellt, da sich diese Materialien während ihrer Lebensdauer verschlechtern und langfristig gefährliche Auswirkungen auf die aquatische Umwelt haben können, insbesondere als Ursprung von Kunststoffabfällen oder als Quelle / Senke für Chemikalien wie Weichmacher und Stabilisatoren, die bei der Herstellung von Geokunststoffen verwendet werden, um deren Leistung zu verbessern. Der Vortrag geht auf diese Bedenken ein. T2 - Geotextilien im Wasserbau CY - Online Meeting DA - 14.04.2021 KW - Wasserbau KW - Geotextilien KW - Beschleunigte Alterung PY - 2021 AN - OPUS4-52434 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Wünsch, Christoph T1 - Reduction of greenhouse gas emissions in waste management N2 - The production of secondary materials from waste materials requires, in most cases, significantly lower energy amounts than the primary material production of raw materials. Along with lower energy demand, the greenhouse gas emissions produced are also lower. The duty of a modern waste management system should therefore be to collect and sort the waste materials in a way that the highest amounts of single material fractions with the highest qualities can be generated. In this contribution, the greenhouse gas balances of the theoretical treatment of the household waste, if collected as mixed waste in sanitary landfills, in waste incineration plants, or in mechanical-biological treatment plants, are compared to the existing separate waste collection and treatment in Germany in 2014. T2 - Richtlinienausschuss VDI 3925 CY - Insel Vilm, Germany DA - 08.05.2018 KW - Culuative energy demand KW - Greenhouse gas balance KW - Waste management PY - 2018 AN - OPUS4-44940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Scholz, Philipp A1 - Gleis, Markus T1 - Aschen und Schlacken aus der Abfallverbrennung im Lichte der Ersatzbaustoffverordnung N2 - Im Rahmen eines vom Umweltbundesamt geförderten Forschungsprojekts wurde untersucht, ob die Abtrennung der Feinfraktion (0-2 mm) eine Verbesserung der umweltrelevanten Eigenschaften bewirkt und somit HMVA-1 erreicht werden kann. In Deutschland wird die Rostasche durch Nassentschlackungssysteme aus dem Feuerraum ausgetragen. Durch den Kontakt mit Wasser setzen direkt hydraulische Reaktionen ein, die eine vollständige Abtrennung der Feinfraktion unmöglich machen. Das wurde bereits in den 1990er Jahren erkannt und führte zur Entwicklung des ABB InRec Verfahrens mit Trockenentaschung als ersten Verfahrensschritt. Auch damals war das Ziel eine möglichst inerte Rostasche für die Verwertung zu erzeugen. In den letzten Jahren wurden in der Schweiz Trockenentaschungssystem installiert, hier vor allem um die Rückgewinnung von elementaren Metallen auch in der Feinfraktion zu verbessern. Welche Potenziale sich dabei erschließen lassen, wurde in einem anderen UBA-Projekt untersucht. Im Rahmen unserer Arbeiten wurde versuchsweise trockene Rostasche an einer Anlage in Süddeutschland genommen und im Labor untersucht. Im Vortrag werden die Ergebnisse zum Auslaugverhalten und zur Gefahreneigenschaft HP14 (Ökotoxizität) vorgestellt. T2 - Jahrestreffen 2024 der DECHEMA-Fachgruppen Abfallbehandlung und Wertstoffrückgewinnung (AuW) und Gasreinigung (GAS) CY - Dresden, Germany DA - 25.03.2024 KW - Rostasche KW - Ersatzbaustoffe PY - 2024 AN - OPUS4-59985 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Economic and legal aspects of secondary resource management N2 - Direct and indirect effects (DIERec) of the recovery of secondary resources are in the range of 500 million tonnes per year in Germany; energy savings are 1.4 million TJ. These savings are between 10 and 20% of the total. The effects of materials recovery exceed those of energy recovery by far with the exception of secondary plastic material where DIERec from energy recovery is higher by factor of 2.7. Untapped potential for the recovery of secondary resources exist in the fine fraction of bottom ash from municipal solid waste incineration, mainly Cu and precious metals and in urban mining. T2 - Travelling Conference Resource efficiency and environmental compatibility in waste management (REECO-WM) CY - Seoul, Ho-Chi-Minh-City, Perth DA - 29.01.2018 KW - Waste management KW - Materials flow KW - Secondary resources PY - 2018 AN - OPUS4-44942 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Fabian A1 - Gehrenkemper, Lennart A1 - von der Au, Marcus A1 - Meermann, Björn T1 - A fast and simple extraction method for the determination of PFASs in soil samples - HR-CS-GFMAS a new screening tool N2 - Here, we describe a fast and simple extraction method for the determination of per- and polyfluorinated alkyl substances (PFASs) utilizing extractable organic fluorine (EOF) sum parameter analysis and high resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS) in soil samples. After extraction and separation of inorganic and organic fluorinated compounds, organically bound fluorinated compounds were indirectly determined via the molecular absorption of gallium mono-fluoride at 211.248 nm. The implementation of the decisions of the “Stockholm Convention on persistent organic pollutants” as well as the “Protocol on Persistent Organic Pollutants of the Convention on Long-Range Transboundary Air Pollution” of the UNECE include the reduction respectively the elimination of PFASs in the environment. Currently, regulations aim to target single compounds (mostly C8-PFAS). But the PFAS group includes over 4700 substances, which are potentially persistent and toxic, thus target analytical approaches are not suitable for a holistic approach investigating the PFAS pollutant situation. Furthermore, forbidden PFASs are substituted by short-chain PFASs, thus the number of unknow substances is steadily increasing. For this reason, sum parameter approaches are more suitable to investigate and assess the pollution situation as well as derive exposure limits. Our developed analytical method was successfully applied to determine PFASs in soil samples from a polluted site. In view of steadily increasing numbers of PFAS substances, our method will make an important contribution in assessing the pollution situation as well as support policy makers in deriving exposure limits for PFAS in the future. T2 - ENSOr - International Workshop on Emerging policy challenges on new soil contaminants CY - Online Meeting DA - 06.05.2021 KW - PFAS KW - HR-CS-GFMAS KW - Soil KW - Sediment PY - 2021 AN - OPUS4-52608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sieksmeyer, Thorben A1 - McMahon, Dino Peter A1 - He, Shulin T1 - Beyond nutrition: host-microbiota interactions drive shifts in the behavioural phenotypes of cockroaches N2 - Recent studies have shown that host-microbiota interactions can lead to dramatic changes in host phenotype especially behaviour. We investigate the causal drivers of microbe-associated shifts in host phenotype by examining how feeding behaviour is modulated by a bacterial infection in an omnivorous cockroach: Blatta orientalis. We conducted food-choice experiments after challenging hosts with the common entomopathogenic soil bacterium Pseudomonas entomophila to understand the impact of bacterial pathogens on host macronutrient preference. We find that immune challenge by this bacterium drives a sharp decline in carbohydrate intake and results in a relative increase in the ratio of protein to carbohydrate consumed. Additionally, infected cockroaches reduce their overall nutrient intake. We show for the first time that cockroach feeding behaviour is dynamically modulated by a pathogen. In contrast to studies on Spodoptera moths, this modulation does not impact any of the immune parameters we measured: it does not affect the abundance of immune related proteins in the hemolymph, hemolymph antimicrobial activity, or survival. This leads to the possibility that as long-lived omnivorous species B. orientalis may be better adapted to unpredictable variation in food availability and quality. An illness-induced anorexia-like response which is thought to assist hosts in limiting nutritional resources available to pathogens is therefore the most likely cause of the observed phenotype. Reduction of carbohydrate intake by sick individuals would be consistent with such an explanation. In another cockroach species Blatella germanica we also investigate whether in addition to pathogens, host microbiota especially gut commensals are causally responsible for shifts in host behavioural phenotype and immune competence. To address this, we conduct food-choice and immunechallenge experiments in germ-free cockroaches and naïve cockroaches. T2 - XI EUROPEAN CONGRESS OF ENTOMOLOGY CY - Neapel, Italy DA - 02.07.2018 KW - Bacterial infection KW - Feeding behaviour KW - Gut microbiota KW - Illness-induced anorexia KW - Proteomics PY - 2018 AN - OPUS4-45414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Herzel, Hannes A1 - Adam, Christian T1 - European Sewage Sludge Ash Monitoring N2 - For the European sewage sludge ash monitoring ash samples from sewage sludge incineration plants were requested from all over Europe. First results of the received samples regarding main and trace element contents were presented at ESPC4. Moreover, a list of all known European facilities for sewage sludge monoincineration was presented. T2 - European Sustainable Phosphorus Conference 4 CY - Vienna, Austria DA - 20.06.2022 KW - Sewage sludge ash KW - Sewage sludge incineration KW - Phosphorus recovery PY - 2022 AN - OPUS4-55145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Analyseverfahren und Messhäufigkeit zur Bestimmung des Phosphorgehalts im Klärschlamm nach AbfKlärV N2 - Auf dem Betreiberforum der DWA-Plattform P-Rück wurden die Empfehlungen für den Vollzug der Phosphorrückgewinnungspflicht aus Klärschlamm vorgestellt. Diese Empfehlungen behandeln die Häufigkeit der Phosphoruntersuchungen im Klärschlamm, wo ein Jahresgang empfohlen wird und eine Empfehlung der Phosphorbestimmung über Aufschluss der Probe in der Mikrowelle und Messung mit ICP-OES. Untermauert wurden die Empfehlungen mit den Ergebnissen von Klärschlamm-Monitoring, Ringversuch und Analytikvergleich aus dem Vorhaben extraWERT. T2 - Betreiberforum der DWA-Plattform P-Rück CY - Stuttgart, Germany DA - 23.06.2022 KW - Klärschlamm KW - Ringversuch KW - Reproduzierbarkeit KW - Phosphorrückgewinnung PY - 2022 AN - OPUS4-55146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Roskosch, A. A1 - Adam, Christian T1 - Ergebnisse des Vorhabens extraWERT N2 - Der Vortrag liefert eine Zusammenfassung der wichtigsten Ergebnisse des extraWERT-Vorhabens mit Schwerpunkt auf den Umsetzungsfragen zur Klärschlammverordnung. Bei diesen Punkten handelt es sich um die Untersuchung von monatlichen Phosphorschwankungen in kommunalem Klärschlamm und die Gleichwertigkeit verschiedener Verfahren zur Phosphorbestimmung in Klärschlamm. T2 - vgbe-Fachtagung Thermische Abfall-, Klärschlammbehandlung und Wirbelschichtfeuerungen 2022 CY - Hamburg, Germany DA - 09.05.2022 KW - Klärschlammverordnung KW - Phosphorrückgewinnung KW - Ringversuch PY - 2022 AN - OPUS4-54843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - BAM-Projekt „extraWERT“: Gleichwertigkeit der nach AbfKlärV zulässigen Verfahren zur Phosphorbestimmung in Klärschlamm N2 - In Deutschland ist ab 2029 eine Phosphorrückgewinnung aus Klärschlamm verpflichtend. Ausgenommen sind Klärschlämme mit weniger als 20 g P/kg TM. Für die Phosphorbestimmung sind verschiedene Methoden nach Klärschlammverordnung als gleichwertig zugelassen: Der Königswasseraufschluss in der Mikrowelle und am Rückfluss sowie die Messung an ICP-OES, ICP-MS und die photometrische Bestimmung mittels Ammoniummolybdaten. An der BAM wurden die unterschiedlichen Methodenkombinationen aus Aufschluss- und Messmethode an 15 Klärschlämmen überprüft und in einem Ringversuch mit einem Klärschlamm getestet. Die Ergebnisse werden in diesem Vortrag zusammengefasst. Als Folge der Untersuchungen wird für die Phosphorbestimmung in Klärschlamm die ICP-OES-Messung nach Königswasseraufschluss in der Mikrowelle empfohlen. T2 - VDLUFA Frühjahrssitzung 2022 der Fachgruppe III Düngemittel CY - Vienna, Austria DA - 18.05.2022 KW - Ringversuch KW - Reproduzierbarkeit KW - Wiederholbarkeit KW - Phosphorrückgewinnung KW - Gleichwertigkeit Messverfahren PY - 2022 AN - OPUS4-54852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian T1 - Nährstoffrückgewinnung aus Klärschlamm: Eine Betrachtung zukünftiger Verwertungsszenarien für Deutschland N2 - Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, in German wastewater treatment plants (WWTPs) phosphorus (P) must be recovered from sewage sludge ifit contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs > 100,000 population equivalents (pe) from 2029 and > 50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 17 % of the total disposal in 2019. The reports of 10 States were evaluated for 2016 and 2017 representing approx. 60 % ofthe total agriculturallyused sludge volume. Whereas phosphorus recovery is mandatory this does not apply to other nutrients. However, many P recovery processes recover other nutrients, too. Considering three differentscenariosfor future German sewage sludge disposal shows that 70 - 77 % ofthe P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0 - 16 % of nitrogen, 36 - 52 % of calcium, 31-53 % of potassium, and 40 - 52 % of magnesium. However, these recovered nut rient loads can substitute only 1 % or less ofthe commercial fertilizer demand except from phosphorus which is about 45 % ofthe demand. T2 - Berliner Klärschlammkonferenz CY - Berlin, Germany DA - 15.11.2021 KW - Phosphor KW - Klärschlammverordnung KW - Phosphorrückgewinnung PY - 2021 AN - OPUS4-54118 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Ergebnisse des Vorhabens extraWERT - Gleichwertigkeit zugelassener Methoden zur Phosphoruntersuchung des Klärschlamms N2 - Die Ergebnisse des extraWERT-Vorhabens wurden Vertreter*innen des Umweltministeriums von Bund und Ländern vorgestellt und im Zusammenhang mit dem Vollzug der AbfKlärV diskutiert. Es ging um die Phosphorschwankungen in kommunalem Klärschlamm und eine Empfehlung der Untersuchungshäufigkeit, um den Phosphorgehalt rechtssicher festzustellen. Des weiteren wurde die Performance verschiedener nach Verordnung gleichwertiger Analyseverfahren für Phosphor in Klärschlamm diskutiert anhand von Ringversuchsergebnissen und Eigenuntersuchungen an 15 Klärschlammproben. T2 - Bund-Länder-Gespräch zum Vollzug der AbfKlärV CY - Online meeting DA - 16.12.2021 KW - Klärschlammverordnung KW - Phosphorrückgewinnung KW - Analytik KW - Ringversuch PY - 2021 AN - OPUS4-54119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Gleichwertigkeit der nach AbfKlärV zulässigen Verfahren zur Phosphorbestimmung in Klärschlamm N2 - In dem Meeting wurde den Notifizierern und Ausrichtern des jährlichen länderübergreifenden Ringversuchs Klärschlamm die Ergebnisse zu Untersuchungen hinsichtlich der Gleichwertigkeit verschiedener nach AbfKlärV zulässiger Verfahren zur Phosphorbestimmung in Klärschlamm vorgestellt. Die Untersuchungen an 15 Klärschlammproben ergaben die höchsten Ergebnisse für das Messverfahren ICP-OES und das Aufschlussverfahren in der Mikrowelle. Diese Ergebnisse wurden im Ringversuch bestätigt. T2 - Meeting der Notifizierer und Ausrichter des länderübergreifenden Ringversuchs (LÜRV) CY - Online meeting DA - 08.12.2021 KW - Klärschlammverordnung KW - Analytik KW - Ringversuch KW - Phosphorbestimmung PY - 2021 AN - OPUS4-54121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Schwankungen der P-Gehalte in Klärschlämmen im Kontext der Klärschlammverordnung N2 - Es wurden die Schwankungen der Phosphorgehalte in kommunalem Klärschlamm vorgestellt. Dazu wurden von 9 Kläranlagen monatlich Klärschlammproben genommen und auf P untersucht. T2 - KlärschlammTage CY - Online Meeting DA - 09.06.2021 KW - Phosphor KW - Klärschlamm KW - Phosphorrückgewinnung KW - Abwasserbehandlung KW - Klärschlammverordnung PY - 2021 AN - OPUS4-52840 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Ehm, J. A1 - Barjenbruch, M. A1 - Pinnekamp, J. T1 - Auswirkungen der novellierten AbfKlärV auf die Kreislaufführung von Pflanzennährstoffen N2 - Die landwirtschaftliche Klärschlammverwertung ist in der Bundesrepublik Deutschland seit Jahren rückläufig. Neben den Risiken durch Schadstoffeinträge gibt es in Deutschland Regionen mit einem stark erhöhten Nährstoffüberschuss. Um die Grundwasserbelastung zu verhindern wurde u.a. das Düngerecht verschärft, was die Flächenkonkurrenz zwischen Klärschlamm und Wirtschaftsdünger vergrößern wird. Es ist davon auszugehen, dass sich die neuen Regelungen im Düngerecht und der Klärschlammverordnung massiv auf die landwirtschaftliche Verwertung von Klärschlamm und damit auf die Kreislaufwirtschaft verschiedener Nährstoffe auswirken werden. In diesem Beitrag werden erste Ergebnisse des Projekts extraWERT vorgestellt. T2 - Klärschlammkonferenz CY - Berlin, Germany DA - 04.11.2019 KW - Klärschlamm KW - Landwirtschaft KW - Makronährstoffe PY - 2019 AN - OPUS4-49604 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Ehm, J. A1 - Barjenbruch, M. A1 - Pinnekamp, J. T1 - Phosphorrückgewinnung - Ergebnisse des Projekts extraWERT N2 - Es wurden erste Ergebnisse des Projekts extraWERT vorgestellt. Im Projekt werden monatlich Klärschlammproben von 10 kommunalen Kläranlagen untersucht, deren P-Gehalt im Grenzbereich der AbfKlärV liegt zwischen 1,7 und 2,3%. Die ersten Ergebnisse lagen zu fünf Kläranlagen vor, es wurden Daten zum TS-Gehalt, zur oTS und zu den Nährstoffgehalten präsentiert. T2 - DWA-Netzwerktag des Nord-Ost CY - Berlin, Germany DA - 22.01.2020 KW - Klärschlamm KW - AbfKlärV KW - Phosphorrückgewinnung KW - Nährstoffe PY - 2020 AN - OPUS4-50300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian T1 - Legislation and technology development for P-recovery in Germany N2 - New developments in legislation and technology development for P-recovery were presented with focus on the situation in Germany. T2 - SMART-Plant joint Stakeholder Workshop CY - Berlin, Germany DA - 29.01.2020 KW - P-recovery KW - Sewage sludge ordinance PY - 2020 AN - OPUS4-51764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - extraWERT – Wertstoffe in Abwasser und Klärschlamm N2 - Im Projekt extraWERT geht es um die Ermittlung von Nährstoffpotenzialen in Abwasser und Klärschlamm. Neben kommunalen Kläranlagen soll auch die Industrie als Quelle für nährstoffreiche Abfallströme betrachtet werden. Mit dem Vortrag sollten Mitglieder des MIV zu einer Projektbeteiligung bewegt werden. Es sollen rohes und gereinigtes Abwasser von direkt einleitenden Betrieben auf Makronährstoffe untersucht werden, neue Erkenntnisse werden insbesondere für die Nährstoffe Calcium und Magnesium erwartet. T2 - Sitzung AG Umwelt Milchindustrie-Verband CY - Kißlegg, Germany DA - 22.10.2019 KW - Klärschlamm KW - Industrielles Abwasser KW - Lebensmittelindustrie KW - Makronährstoffe PY - 2019 AN - OPUS4-49607 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa T1 - Vorstellung des REFOPLAN-Projekts extraWERT Erhebung zusätzlicher Wertstoffpotenziale in Klärschlamm N2 - Auf dem Regionalgruppentreffen wurden erste Projektergebnisse vorgestellt und die Probenahmestrategie diskutiert. Vorgestellt wurde eine Rückberechnung der mittleren Wertstoffgehalte aus dem Klärschlamm-Monitoring 2014 (Krüger und Adam) und erste Auswertungen der Klärschlammbericht-Rohdaten aus NRW und Hessen. T2 - DWA-Regionalgruppentreffen Brandenburg-Berlin CY - Fürstenwalde, Germany DA - 04.04.2019 KW - Klärschlamm KW - Landwirtschaft KW - Makronährstoffe KW - AbfKlärV PY - 2019 AN - OPUS4-49609 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seneschal-Merz, Karine A1 - Bücker, Michael A1 - Wachtendorf, Volker A1 - Heidrich, Christa A1 - Sander, Christoph T1 - New UV-protective glazing for the conservation of cultural assets N2 - For centuries, churches, secular buildings and museums have been furnished with valuable works of art. Many works of art are UV- and light-sensitive. It is well known that especially UV radiation causes damage and discoloration in paintings, textiles, plastics, wood and other materials. In particular, the wavelengths between 280 and 410 nm cause color changes, embrittlement or destruction of e.g. plastics over time. Therefore, strongly UV-absorbing glasses are advantageous for architecture and are necessary for the protection of cultural assets. As restorers in all disciplines become more and more aware, the demands placed on buildings and their furnishings in terms of climate are becoming increasingly detailed and precise. The aim in each case is to preserve the valuable artwork. For some years now, the industry has been offering the protection of cultural objects by installing special UV-protective glasses. Currently, UV protection for church buildings is realized by laminated safety glass equipped with appropriate UV-protective plastic films. Technically, this always means a second pane of glass in front of the windows, which is installed outside the building. This creates climatic gaps that are difficult to control and deterioration due to ageing effects can be expected. At the same time, this protective glazing is not invisible and has a considerable aesthetic influence on the interior and exterior appearance of the building. Meanwhile, the preservation of historical monuments accepts such aesthetic cuts on buildings in order to protect the artwork in the interior from UV light. To this day, however, the long-term durability of UV protection provided by inserted plastic films is still controversial. To date the only available alternative on the market is a mouth-blown UV protection glass which uses a so-called overlay to provide UV protection. This shows that UV protection can also be achieved by glasses without plastic films thus realizing an exclusive inorganic protection which normally is more stable than a polymeric one. So far there are not enough studies to prove long-term durability. The aim of this project is to provide existing glazing or new glazing to be created with a highly transparent layer that ensures this UV-protective filter function below 400 nm. The glass coating is to be applied to the glass over a large area and fired into the surface like a classic ceramic enamel paint with the same technics. In addition, it should be long-term durable in its function. It means, that the glass has to be fused at temperatures below 630 °C during the firing process, its chemical durability has to be high, its coefficient of thermal expansion has to be as close as the one of the substrate (usually float glass) and the glass has to absorb the UV-radiation within a thin thickness (thinner as 100 µm). In this project, the long-term durability of commercial UV-protective glasses is examined. New low melting glasses containing UV-absorbing ions are being developed. Their UV-absorption as a thin layer is analyzed as well as their chemical durability and their thermal properties. We are grateful to BMWI for the financial support in the frame of the Central Innovation Programme for SMEs (ZIM). T2 - HVG-DGG: 94. Glastechnische Tagung CY - Online meeting DA - 10.05.2021 KW - Glass KW - Low melting KW - Chemical durability KW - Weathering tests KW - Aging test KW - UV absorption KW - UV protection KW - Architecture KW - Optical properties PY - 2021 AN - OPUS4-52648 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seneschal-Merz, Karine A1 - Bücker, Michael A1 - Sander, C. T1 - Development of low melting glasses as durable transparent enamel colors for the manufacture of decorated glass panels N2 - Today glass is broadly used in modern architecture. For applications indoor it is possible to produce decor glass by using enamel colors and glass painting techniques without any problems. However, this is more limited for applications outdoor. Humidity and environmental pollution attack the surface of the coating and damage it strongly. There are only few colors on the market which are resistant towards acids and bases until now. Additionally, most of those colors are opaque. In order to extend the color palette, chemically resistant colored glasses are being developed which are transparent, relatively low melting and intensively toned even in thin coat thickness. To achieve such ambitious aim, many parameters have to match which act in complex manner. Metal oxides were used to color the glasses. A lead-free glass composition was developed to avoid an exposition of heavy metals to the environment. The glasses were characterized, in particular in terms of their thermal properties, their crystallization and corrosion behavior as well as their chemical and environmental durability. Different practical applications will be shown. T2 - 15th International Conference on the Physics of Non-Crystalline Solids & 14th European Society of Glass Conference CY - Saint-Malon, France DA - 08.07.2018 KW - Glass KW - Chemical durability KW - Corrosion KW - Enamel colors KW - Low melting KW - Environmental friendly KW - Architecture KW - Thermal properties PY - 2018 AN - OPUS4-45755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Overview on the EMPIR Project "AEROMET" N2 - Overview on the ongoing EU EMPIR Project "AEROMET" Aerosol Metrology for Atmospheric Science and Air Quality, Overview on preliminary resuilts in Workpackages 3 "Calibration of MPSS and CPCs" and 4 "Quantifying airborne particle compositions in the field" T2 - Meeting des ISO TC24/SC4, Joint session of Working Groups 9 "Single particle light interaction methods" and 12 "Electrical mobility and number concentration analysis for aerosol particles" CY - Graz, Austria DA - 11.04.2019 KW - Ambient air pollution KW - EU EMPIR KW - Chemical analysis KW - Total reflection X-ray spectroscopy KW - Airborne Particles PY - 2019 AN - OPUS4-47820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Instruments for Fine and Ultrafine Particle Emission Characterization N2 - An overview on instruments and methods for the measurement and chemical characterization of particulate emissions from local sources is presented T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - Aerosol spectroscopy KW - Particulate emission KW - Chemical analysis KW - Total reflection X-ray spectroscopy KW - Calibration PY - 2019 AN - OPUS4-47816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Regulatory Trends in the EU for Chemicals and Nanomaterials N2 - The presentation gives an overview on existing and upcoming REACH regulations in the EU concerning nanomaterials. T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - Nanomaterials KW - REACH KW - EU regulations PY - 2019 AN - OPUS4-47814 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Analysis of air pollutants in ambient and indoor aerosolsby TXRF - application examples N2 - Quantitative chemical analysis of airborne particulate matter (PM) is vital for the understanding of health effects in indoor and outdoor environments, as well as for enforcing air quality regulations. Typically, airborne particles are sampled over long time periods on filters, followed by lab-based analysis, e.g., with inductively coupled plasma mass spectrometry (ICP-MS). Within the EURAMET EMPIR AEROMET project, cascade impactor aerosol sampling was combined for the first time with on-site total reflection X-ray fluorescence (TXRF) spectroscopy to develop a tool for quantifying particle element compositions within short time intervals and even on-site. This makes variations of aerosol chemistry observable with time resolution of only a few hours and with good size resolution in the PM10 range. A proof of principles of this methodological approach and the comparison to standard methods within the scope of a field campaign will be presented. Secondly, aerosol sampling and TXRF analysis seems suitable for the quantification of elements in indoor aerosols as well and may provide an important enhancement of existing methods for the analysis of organic species in aerosols (such as sampling and TD-GC/MS). As an example, the TXRF analysis of particles emitted from laser printers under controlled conditions in an environmental test chamber will be presented. T2 - TXRF Journal ClubB CY - Online meeeting DA - 24.02.2022 KW - Aerosol KW - TXRF KW - Cascade impactor KW - ICP-MS KW - Particles KW - Air quality monitoring KW - Element mass concentration PY - 2022 AN - OPUS4-54418 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan A1 - Osan, J. A1 - Czömpöly, O. A1 - Gross, A. A1 - Stoßnach, H. A1 - Stabile, L. A1 - Ochsenkuehn-Petropoulou, M. A1 - Tsakanika, L. A. A1 - Lymperopoulou, T. A1 - Goddart, S. A1 - Fiebig, M. A1 - Gaie-Levrel, F. A1 - Rissler, J. A1 - Kayser, Y. A1 - Beckhoff, B. T1 - Element mass concentrations in ambient aerosols, a comparison of results from filter sampling & ICP-MS ans cascade impactor sampling & mobile total reflection X-RAY fluorescence spectroscopy N2 - Quantitative chemical analysis of airborne particulate matter (PM) is vital for the understanding of health effects in indoor and outdoor environments and required by EU air quality regulations. Typically, airborne particles are sampled on filters, followed by lab-based analysis, e.g., with inductively coupled plasma mass spectrometry (ICP-MS). Within the EURAMET EMPIR AEROMET project, cascade impactor aerosol sampling was combined with on-site total reflection X-ray fluorescence (TXRF) spectroscopy. The study aimed at a proof of principles for this new mobile and on-size tool for the quantification of aerosol element compositions and element mass concentrations within short time intervals of less than 12 h. In a field campaign the method’s technical feasibility could be demonstrated. The TXRF results were traced back to a stationary, reference-free XRS setup in the laboratory of the German national metrology institute PTB at the BESSY II electron storage ring in Berlin, Germany. Simultaneous PM10-filter sampling, followed by standardized lab-based analysis, allowed for a comparison of the field campaign data of both methods. As Fig. 1 shows, the correspondence between PM10 filter sampling and ICP-MS, and on the other hand, cascade impactor sampling and TXRF is quite encouraging. However, for some of the analysed elements, e.g. V and Pb, the observed deviations are higher than expected and this highlights the fact, that spectral deconvolution strategies for TXRF on cascade impactor samples still need some improvement. This work was supported by the EMPIR programme, co-financed by the Participating States and from the European Union’s Horizon 2020 research and innovation programme, through grant agreements 16ENV07 AEROMET and 19ENV08 AEROMET II T2 - 12th International Conference on Instrumental Methods of Analysis (IMA-2021) CY - Athens, Greece DA - 20.09.2021 KW - Aerosol KW - TXRF KW - Reference method KW - Cascade impactor KW - Ambient aerosols KW - Air quality monitoring KW - Element mass concentration KW - Size resolved chemical composition KW - Time resolved chemical composition KW - ICP-MS PY - 2021 AN - OPUS4-53597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan A1 - Osan, J. A1 - Gross, A. A1 - Stabile, L. T1 - AEROMET - Observation of quickly changing element mass concentrations in an ambient aerosol using portable TXRF N2 - Measurements of aerosol particles are vital for enforcing EU air quality regulations to protect human health, and for research on climate change effects. Although metrics such as PM10 and PM2.5 are currently in use, the level of uncertainty of aerosol metrics is too high and the traceability is insufficient. The project AEROMET, which has been started in June 2017 aims at implementing improvements in a) the uncertainty of particle mass, size and number concentration measurements and b) in the characterization of regulated components in airborne particles. Both are demanded by existing networks within the EU as well as by global atmospheric research. On-site measurement campaigns One of the objects is the application of mobile x-ray spectroscopy techniques combined with aerosol sampling techniques for quantifying particle compositions in the field for real time analysis. During two in-field measurement campaigns in Budapest, Hungary in May 2018 and Cassino, Italy in September 2018 the size dependent mass concentrations of specific elements in ambient aerosols were monitored under dynamic conditions. Typically, airborne particles are sampled on filter substrates. During this project new sampling methods with specially designed substrate holders for an in-situ TXRF analysis were developed and applied for the first time. This approach allows a direct time and size resolved analysis without laborious digestion steps and a reduced risk of contamination. Aerosol particles were sampled in a 13-stage DLPI impactor - size range from 0,03 µm to 10 µm - which was equipped with special adapters for acrylic discs of 30 mm diameter, serving as substrates. TXRF analysis was performed on site with the transportable spectrometer S2 PICOFOX (Bruker Nano GmbH) equipped with a Mo X-ray tube and a 30 mm² Silicon Drift Detector (SDD). Excitation conditions were 50 kV, 600 µA, measurement time 1000 s. Quantification was based on internal standardization using 50 ng of Y in solution, which was pipetted into the centre of the discs prior to sampling. At moderate air pollution levels, i.e. PM10 ~ 20 µg/m³, sampling times of less than 2 hours were enough for the detection of elements in different particle size bins. The in-situ approach and the high sensitivity of TXRF enables the observation of rather quick changes in the quantity and distribution of elements in an ambient aerosol on the day of sampling, as the below example from the Cassino field campaign on 11 Sept. 2018 shows: The analysis of the morning and afternoon sampling shifts reveals the occurrence of the elements Fe, Ca and Si in different size bins as well as their significant temporal change in respective mass concentrations over the day while the distributions of several other elements in the aerosol remain unchanged. The validation of these results by backup measurements is planned. T2 - European Aerosol Conference EAC 2019 CY - Gothenburg, Sweden DA - 25.08.2019 KW - TXRF KW - Ambient air KW - Aerosol KW - Cascade impactor KW - Element analysis PY - 2019 AN - OPUS4-49582 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - VOC, Fine and Ultrafine Particles Emissions from Additive Manufacturing and 3D-Printers N2 - The presentation gives an overview on Additive Manufacturing techniques and related potential risks from emission of hazardous gases and aerosols, based on emission characterizations in BAM. Voluntary mitigation strategies are presented T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - 3D Printing KW - Additive Manufacturing KW - Particulate emissions KW - Emissions of hazardous gases KW - Filament comparison PY - 2019 AN - OPUS4-47812 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - UBA Projects on Particulate Emissions from Laser Printers N2 - The presentation gives an overview on past and ongoing projects in BAM on laser printer particulate emissions, funded by the German Environment Agency (UBA) in order to further develop award criteria for the Blue Angel ecolabel for office machines T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - Laser Printer KW - Particulate emission KW - Blue Angel ecolabel KW - Office machines PY - 2019 AN - OPUS4-47811 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schütter, Jan A1 - Pietsch, Franziska A1 - Schreiber, Frank A1 - Koerdt, Andrea A1 - Özcan Sandikcioglu, Özlem T1 - Effect of surface topography and chemistry on the attachment of bacteria on solid surfaces N2 - Microbiologically induced corrosion due to bacterial biofilms causes several problems in industrial systems, technical applications and in medicine. Prior to the formation of a biofilm on a substrate, planktonic cells attach on the surface. Hence, the properties of the surface play a key role in biofilm formation and are of great importance for the development of strategies to prevent bacterial attachment and biofilm formation. This project aims at clarifying to which extent surface micro-/nanostructuring and chemical functionalization affects bacterial attachment and whether a synergistic combination of the two can be used to control bacterial adhesion. To answer these questions, model surfaces with regular patterns of 5-10 micrometers in size have been prepared, which provide distinct zones differing in terms of their chemistry or nano-roughness. This was achieved by micro contact printing of self-assembled monolayers with different functional groups and deposition of patterned ZnO nanorod arrays for studying the effect of surface chemistry and morphology, respectively. Typical contrasts studied were combinations of positively/negatively charged, hydrophobic/hydrophilic or flat/rough. The attachment behavior of bacteria on tailored surfaces were studied in a flow chamber as a function of time. The strain Pseudomonas fluorescens SBW25 was chosen as a model organism. DNA-intercalating dyes such as Syto9 have a high affinity to adsorb on ZnO nanorods. To overcome this limitation a genetic modification was performed by introducing a gene which expresses a green fluorescent protein in P. fluorescens SBW25 enabling the quantitative evaluation of the flow chamber studies by means of fluorescence microscopy. Further analysis of the attachment behavior was performed by means of scanning electron microscopy. The presentation will summarize the results of our systematic study on the role of individual parameters on bacterial attachment and highlight synergistic combinations, showing an inhibition or enhancing effect. As the investigations with model substrates enable a precise control of the surface parameters, this approach can be applied to different microorganisms and material systems to achieve a correlative description of bacterial adhesion on solid surfaces. T2 - Eurocorr2019 CY - Sevilla, Spain DA - 09.09.2019 KW - Microbial KW - Corrosion KW - MIC KW - Nanorods PY - 2019 AN - OPUS4-49730 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schühle, Florian A1 - Richter, Matthias T1 - Bereitstellung qualitätsgesicherter VOC-Aufnahmeraten für axiale Passivsammler N2 - Quality assured uptake rates for passive sampling of indoor air VOCs Passive sampling of VOCs with Tenax® TA and thermal desorption GC-MS analysis is a simple, cost efficient and representative method to determine VOCs concentrations in indoor air. In theory, the uptake into the passive sampler is only dependent on the diffusion coefficient of the analyte in air and the geometry of the sampler (ideal adsorption). For characterization, the uptake rate (UR) is used, defined as the ratio of the uptaken mass and the product of ambient concentration and exposure time. Various reported effective uptake rates (UR,eff) differ considerably from ideal values (UR,id). Literature values in national and international standards, are essentially sorted by the applicable exposure time, while detailed information about the corresponding concentration range is lacking. Moreover the number of itemized substances is limited. The aim of this study was to review and expand this set of uptake rates by determination of own quality assured laboratory values.The determined uptake rates are considered accurate in terms of RSD and comparability to literature values and can be recommended for exposure times of seven days at 50 100 µg/m³ (approximately 100 300 ppm min). Seven day uptake rates in ISO16017 2 and ASTM D6196 are not generally suited for this purpose, as has been exemplarily shown for benzene. N2 - Die passive Probenahme von VOC (Volatile Organic Compounds) mit Tenax® TA und Thermodesorption GC/MS Analytik ist eine einfache, kosteneffiziente und repräsentative Methode zur Bestimmung der VOC-Konzentrationen in der Innenraumluft. In der Theorie ist die Stoffaufnahme in den Passivsammler nur abhängig vom Diffusionskoeffizienten der Substanz in Luft und der Geometrie des Sammlers (ideale Adsorption). Um sie zu charakterisieren, wird die Aufnahmerate (UR), definiert als Quotient der Massenaufnahme und dem Produkt aus Konzentration und Expositionszeit, verwendet. Viele effektive Aufnahmeraten (UR,eff) unterscheiden sich beträchtlich von idealen (theoretischen) Werten (UR,id). Literaturwerte sind in nationalen und internationalen Normen lediglich für bestimmte Expositionszeiten vorgegeben, während detaillierte Informationen über den zugehörigen Konzentrationsbereich fehlen. Außerdem ist die Anzahl der insgesamt in der Literatur beschriebenen Substanzen begrenzt. Das Ziel der vorgestellten Studie ist es diesen Fundus an Aufnahmeraten zu begutachten und zu prüfen und ihn durch die Bestimmung eigener qualitätsgesicherter Laborwerte zu ergänzen. Die bestimmten Aufnahmeraten werden als akkurat bezüglich ihrer relativen Standardabweichung und Vergleichbarkeit zu Literaturwerten betrachtet und können für Expositionszeiten von 7 Tagen bei Konzentrationen von 50 100 µg/m³ (ca. 100 300 ppm min) empfohlen werden. Die Sieben Tage Aufnahmeraten aus ISO16017 2 und ASTM D6196 sind nicht generell für diesen Zweck geeignet, wie exemplarisch für Benzol gezeigt wurde. T2 - Kongress 29. WaBoLu-Innenraumtage CY - Berlin, Germany DA - 24.05.2022 KW - IAQ KW - VOC KW - Passive sampling KW - Uptake rate PY - 2022 SN - 978-3-949241-04-8 AN - OPUS4-55209 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schühle, Florian A1 - Richter, Matthias T1 - Determination and classification of seven-day uptake rates for indoor air VOCs into tube type diffusive samplers with Tenax® TA N2 - Axial passive sampling of VOCs with Tenax® TA and thermal desorption GC-MS analysis is an accepted alternative to active sampling in occupational hygiene. In theory, the uptake into the passive sampler is only dependent on the diffusion coefficient of the analyte in air and the geometry of the sampler (ideal adsorption). For characterization, the uptake rate (UR) is used defined as the ratio of the mass adsorbed and the product of ambient concentration and exposure time. Various reported effective uptake rates (UR,eff) differ to an increasing degree from ideal values (UR,id) with increasing exposure doses (denominator of the given definition of UR), (Tolnai, 2001). In national and international standards, uptake rates are essentially sorted by the applicable exposure time, while detailed information about the corresponding concentration range is lacking. Moreover, especially for long exposure periods as applied in indoor air monitoring, the number of itemized substances is limited. Therefore it is the aim of this contribution to review and expand uptake rate data by comparison of literature and own laboratory values of assured quality. Passive samplers were exposed to nine single compound atmospheres of known concentrations for seven days. Concentrations were checked twice a day via active sampling.The determined uptake rates are considered accurate in terms of RSD and comparability to literature values and can be recommended for exposure times of seven days at 50 – 100 μg m-3 (approximately 100 – 300 ppm min). Seven-day uptake rates in ISO16017-2 and ASTM D6196 are not generally suited for this purpose, as has been exemplarily shown for benzene. Thus, it is crucial for optimization of the method to produce more reliable uptake rate data, including specific information about applicable exposure times and concentrations, which will be promoted in the course of this ongoing study. T2 - Healthy Buildings America 2021 CY - Online meeting DA - 18.01.2022 KW - Diffusive sampling KW - Volatile organic compounds (VOC) KW - Effective uptake rate PY - 2022 UR - https://www.isiaq.org/docs/HB2021America262.pdf AN - OPUS4-54372 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Light-dependent development in Botrytis cinerea N2 - Sunlight is an important environmental factor is almost all ecosystems by being a source of energy, information, and stress. All organisms must protect themselves from the harmful effects of light such as UV radiation, ROS accumulation, heat, and desiccation. Finally, light qualities and quantities can be used for decision making, timing and as guide for directed growth when they are sensed and transduced into intracellular signals. Botrytis cinerea and other plant pathogens infecting the sun-exposed parts of the plant must cope with the high light conditions the host plant seeks. Further they experience an altered light spectrum (‘green gap’) when they colonize shaded parts of the plant; it is depleted for blue and red light that is absorbed by the plant chlorophyll and enriched for green and far-red light that is reflected or transmitted by the plant tissue. As these ambient light conditions trigger the shade avoidance response in the plant, the pathogens may trigger their own ‘shading response’ such as the upregulation of virulence determinants and inoculum production. B. cinerea maintains a highly sophisticated light signaling machinery that senses different light qualities to trigger a variety of responses, that are protection, morphogenesis, positive and negative tropisms, and entrainment. These characteristics render B. cinerea a valuable model to enlighten the role of light in parasitic fungus-plant interactions and beyond. The vegetative mycelium – the core of all infection and developmental programs – is not visibly pigmented and thus considered to be sensitive to biotic and abiotic stresses. However, the vegetative hyphae have a very limited half-life and are usually restricted to the invasive growth phase in which they are protected from light by the plant tissue. Fast colonization of host tissues and by this proper nutrient acquisition enables the rapid formation of long-lasting reproduction structures (melanized conidiophores with conidia, sclerotia) on the surfaces of rotted plant tissues. Depending on the light and temperature conditions, conidiation or sclerotial development is initiated. Taken together, B. cinerea uses light-regulated signaling networks to avoid light whenever possible; for example, by minimizing the half-life of sensitive cells that are hiding in plant tissues and by scheduling critical steps such as conidiogenesis, conidial germination and penetration of plant tissues for the night. T2 - BotrySclero2022 CY - Avignon, France DA - 13.06.2022 KW - Fungus KW - Light KW - Stress KW - Melanin PY - 2022 AN - OPUS4-55248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Fungi in extreme habitats: Lessons from the microcolonial black fungus Knufia petricola N2 - Fungi that share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. But to cope with sunlight-associated stresses [e.g. high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses] it is important for fungi to accurately sense and respond to changes in light. The genomes of black [dihydroxynaphthalene (DHN) melanin-containing] fungi from phyllosphere and exposed solid surfaces contain multiple photoreceptors (PRs). The plant pathogen Botrytis cinerea (Leotiomycetes) has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess equal numbers of PRs along with the same set of protective pigments. This similarity between black fungi from plant and rock surfaces suggests that photoperception and -regulation are important for fungi that receive nutrients through cooperation with phototrophs. T2 - Gordon Research Conference "Cellular and Molecular Fungal Biology" CY - Holderness, NH, USA DA - 26.06.2022 KW - Light KW - Stress KW - Photoperception KW - Pigments PY - 2022 AN - OPUS4-55249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Breitenbach, Romy A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Heeger, Felix A1 - Nitsche, Sarah A1 - Tonon, Chiara A1 - Voigt, Oliver A1 - Gorbushina, Anna T1 - Knufia petricola – a model for exploring the biology of black rock-inhabiting fungi N2 - Black fungi also called black yeasts, rock-inhabiting fungi or microcolonial fungi are a group of Ascomycetes [Eurotiomycetes, Arthoniomycetes and Dothideomycetes] that exhibit high stress tolerance, yeast‑like or meristematic growth, and constitutive 1,8-dihydroxynaphthalene (DHN) melanin formation. They dominate a range of hostile natural and man‑made environments – from desert rocks and salterns to dishwashers, roofs, and solar panels. Due to their slow growth and the lack of sexual cycles and genetic tools, the underlying mechanisms of black fungi’s phenotypic traits have remained largely unexplored. We consider the rock inhabitant K. petricola [Eurotiomycetes, Chaetothyriales] a suitable model for studying the phenotypic characteristics of black fungi. With K. petricola the regulation of pigment synthesis, general stress responses and the unusual modes of cell division can be dissected by advanced reverse and forward genetics approaches. The genome of K. petricola strain A95 was sequenced using a combination of short high quality Illumina reads and long PacBio reads. The final assembly consists of twelve contigs: five complete chromosomes and six contigs with one telomer each. Gene annotation supported by transcriptomics and proteomics data was manually curated. Recently, we developed a set of genetic tools to manipulate the genome for analyzing gene functions and studying the cell biology. This set includes CRISPR/Cas9-based genome editing and live-cell imaging using genetically encoded fluorescent proteins, as well as protocols for -omics approaches and for simulation of mineral weathering in the laboratory. Mutants defective in DHN melanogenesis, carotenogenesis or both processes are currently studied to elucidate the role of these protective pigments in tolerance of natural and man-made stresses, weathering of olivine, penetration of marble, and adhesion to surfaces. Further, the established protocols and knowledge gained from K. petricola form a starting point for making other extremotolerant black fungi accessible to genetic manipulation. T2 - 31st Fungal Genetics Conference CY - USA, CA, Pacific Grove DA - 15.03.2022 KW - Black fungi KW - Melanin KW - Genome editing PY - 2022 AN - OPUS4-54585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Photoperception in plant- and rock-associated black fungi N2 - Fungi that share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. Sunlight-associated stresses are however multiple: high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses. Ascomycota dominating light-flooded habitats accurately sense and respond to changes in light using it as a cue to coordinate growth, stress responses as well as to establish pathogenic or symbiotic relationships. Two species from two light-flooded habitats – phyllosphere and sun-exposed solid surfaces – were analysed for their photoreceptor distribution. In both habitats phototroph-associated and black [dihydroxynaphthalene (DHN) melanin-containing] fungi are prevalent. This diversity was sampled with the plant-associated fungus Botrytis cinerea (Leotiomycetes), while Knufia petricola (Eurotiomycetes) was included as a typical biofilm-former on sun-exposed solid surfaces e.g. rocks, building facades, roofs, and solar panels. The analysis has shown that genomes of black fungi contain more photoreceptors than animal pathogens and saprophytes such as Aspergillus nidulans and Neurospora crassa1,2. B. cinerea that causes the grey mould disease by infecting the above-ground parts of more than 200 dicots has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts1. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess equal numbers of photoreceptors along with the same set of protective metabolites i.e. melanin, carotenoids and mycosporines2. This similarity between black fungi from plant and rock surfaces suggests that photoperception and -regulation are important for sun-stressed fungi that receive nutrients through cooperation with phototrophs. CRISPR/Cas9-based genetic tools for manipulating K. petricola were established3 and are currently used for elucidating the functions of the different photoreceptors in the biology of rock-inhabiting fungi. This work was supported by the grant SCHU 2833/4-1 from the German Research Foundation (DFG) and internal funds of the BAM. T2 - 19th Congress of the European Society for Photobiology CY - Online meeting DA - 30.08.2021 KW - Fungi KW - Light KW - Extreme environments PY - 2021 AN - OPUS4-53191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - How light determines the life of the plant pathogen Botrytis cinerea N2 - The rotation of the Earth causes a day/night cycle that is characterized by changing light and temperature conditions. Fungi actively sense the environmental light conditions to induce protective mechanisms against the light-associated stresses and to regulate development. Since fungi adapted to habitats with different light regimes, the complexities of their ‘visual’ systems and photoresponses may vary significantly. Fungi that are associated with plants experience a special light regime because the host seeks optimum light conditions for photosynthesis – and the fungus must cope with them. Moreover, fungi living under the canopy are confronted with an altered spectrum enriched for green and far-red light. Plants sense light to coordinate growth and morphogenesis: a low red:far-red ratio indicates the presence of competitors (shading by other plants) and triggers the shade avoidance response which is accompanied by increased susceptibility to nectrophic pathogens. Botrytis cinerea, the causal agent of gray mold diseases on many plant species in moderate climate zones (high humidity, temperatures around 20°C, seasons), exhibits striking photoresponses accompanied by a broad action spectrum and a high number of photoreceptors. Light is the most important factor controlling morphogenesis: it induces conidiation for disease spreading (summer cycle) and represses sclerotial development for survival and/or sexual recombination (winter cycle). In the past years, we identified several cellular components involved in photoperception and regulation of photomorphogenesis and virulence indicating that the same signaling pathways are of relevance for both processes, propagation and infection. Notably, we recognized the role of the phytochromes (red/far-red light sensors) for coordinated responses to light and elevated temperatures (photo-/thermomorphogenesis) – similar to the function of Arabidopsis PhyB. BcPHY2-like thermosensors are likely restricted to the Leotiomycetes, which include several plant pathogens of the moderate climate zones. T2 - Fungal Genetics Conference 2019 CY - Asilomar, CA, USA DA - 12.03.2019 KW - fungus KW - light KW - plant pathogen KW - signaling KW - virulence PY - 2019 AN - OPUS4-48128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Photoperception in black fungi that share niches with green organisms N2 - Sunlight, the major source of energy, drives life but in excess it provokes UV-induced DNA damage, accumulation of reactive oxygen species, desiccation, osmotic stresses and so on. Biological strategies to survive excess light include protection, avoidance and active utilisation. Phototrophic organisms including cyanobacteria, green algae and plants use all three strategies. Fungi occupying phototrophic niches may profit from the surplus photosynthetic products which also obliges them to cope with the same light-induced stresses. One way of handling these stresses would be to use similar signalling pathways to sense the presence and to interact with their phototrophic partners. Obviously, the levels of adaptation and responses to light will depend on the environment as well as fungal genotype and phylogenetic position. Black fungi – a polyphyletic group – accumulate the dark pigment DHN melanin in their cell walls and often occupy light-flooded habitats from phyllosphere to rock surfaces. Here we compare two sequenced melanised fungi of different lifestyles in their response to light. The Leotiomycete Botrytis cinerea is an aggressive pathogen that primarily infects the above-ground parts of plants. It possesses large numbers of photoreceptors that respond to a broad spectrum of light. As a consequence, light controls morphogenesis in which it induces conidiation for disease spreading and represses sclerotial development for survival and/or sexual recombination. Cellular components involved in photo-perception and regulation of morphogenesis, stress responses and virulence have been identified and appear to regulate propagation, survival and infection. These include phytochromes, a group of photoreceptors which are particularly enriched in the Leotiomycetes and that mediate coordinated responses to light and elevated temperatures. Assuming that photo-regulation may be equally important for fungi that live in mutualistic relationships with phototrophs either by forming composite organisms or biofilms, we investigate the role of light in the rock-inhabiting Eurotiomycete Knufia petricola. Like other black yeasts, K. petricola grows slowly, does not form specialised reproductive structures and constitutively produces DHN melanin as well as carotenoids. Combining K. petricola with the cyanobacterium Nostoc punctiforme, we developed a model system for studying biofilm formation and bio-weathering. A genetic toolbox to manipulate this model system is being developed. K. petricola strain A95 possesses ten putative photoreceptors, more than found in filamentous Eurotiomycetes suggesting that light plays an important role for abiotic and biotic interactions in extremo-tolerant and symbiosis-capable fungi. T2 - International Symposium on Fungal Stress (ISFUS) CY - Sao Jose dos Campos, Brazil DA - 19.05.2019 KW - Botrytis KW - carotenoids KW - Knufia KW - melanin KW - Nostoc PY - 2019 AN - OPUS4-48130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Many-sided DHN melanin – spotlight on its function in microcolonial black fungi N2 - Dihydroxynaphthalene (DHN) melanin is produced by different Ascomycetes via slightly differing biosynthetic routes. The polyketide synthases (PKS) release the heptaketide YWA1, the hexaketide AT4HN or the pentaketide T4HN. The first two products are deacetylated by ‘yellowish-green’ hydrolases to T4HN, and T4HN is further converted by a core set of enzymes to DHN. Final polymerization steps are accomplished by multicopper oxidases. DHN melanogenesis is often regulated in a spatial and temporal fashion resulting e.g. in melanized reproduction, survival and/or infection structures. Remarkable is the regulation of the DHN melanogenesis in the foliar plant pathogen Botrytis cinerea: it involves two differently expressed PKSs providing the precursor in conidia and sclerotia, respectively (Schumacher 2016, Mol Microbiol). In contrast, a polyphyletic group of Ascomycetes (microcolonial fungi/ black yeast) dwelling in hostile habitats such as bare rock surfaces in hot and cold deserts, exhibits constitutive melanogenesis. Here, DHN melanin builds a protective layer around all vegetative cells thus contributing to the survival of diverse environmental stresses even without specialized reproduction structures. As part of our continuing research on microcolonial rock-inhabiting fungi, we chose the genetically amenable Knufia petricola strain A95 (Nai et al. 2013, Fungal Genet Biol; Noack-Schönmann et al. 2014, AMB Express) for detailed studies. DHN-deficient mutants generated by targeted mutation of biosynthetic genes were studied with regard to the architecture of the cell wall and the EPS (extracellular polymeric substances) matrix, attachment to and weathering of olivine, as well as the tolerance to abiotic and biotic stresses. We will discuss the critical role of the outer cell surface (DHN melanin and EPS) in adhesion to the substrate and subsequent damage of the colonized surface. T2 - European Conference on Fungal Genetics (ECFG15) CY - Rome, Italy DA - 17.02.2020 KW - fungus KW - melanin KW - pigmentation PY - 2020 AN - OPUS4-50591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Genetic manipulation of the microcolonial black fungus Knufia petricola N2 - Microcolonial black fungi, a polyphyletic group of ascomycetes, exhibit constitutive melanin formation, yeast-like growth and high stress tolerances. They dominate – often together with bacteria and algae in sub-aerial biofilms – a range of hostile environments including natural and man-made ones, from salterns to dishwashers, roofs and solar panels. Because of lacking genetic tools and the slow growth of most isolates, the genetic bases for these specific properties are largely unknown. The rock-inhabiting fungus Knufia petricola (Eurotiomycetes, Chaetothyriales) exhibits all characteristics of microcolonial black fungi and was selected as recipient for genetic engineering to study gene functions and genetic interactions. Different variants of green and red fluorescent proteins were successfully expressed indicating that fluorescence microscopy using genetically encoded fluorescent proteins and fluorescent dyes enables various cell biology approaches. Furthermore, genes of biosynthetic pathways (DHN melanin, carotenoids, uracil, adenine) were successfully mutated by applying traditional gene replacement and plasmid-based or ribonucleoprotein (RNP)-based CRISPR/Cas9 or silenced by RNA interference (RNAi). The availability of this advanced and efficient genetic toolbox and the annotated genome sequence of strain A95 makes K. petricola an excellent model for exploring the secrets of microcolonial black fungi. T2 - Departmental colloquium of the Tuscia University CY - Viterbo, Italy DA - 14.02.2020 KW - black fungus KW - genetics KW - Crispr/Cas9 PY - 2020 AN - OPUS4-50592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Photoregulation of Metabolism in Plant- & Rock-associated Black Fungi N2 - Fungi that share light-flooded habitats with phototrophs may profit from excess photosynthetic products. But to cope with sunlight-associated stresses it is important for fungi to accurately sense and respond to changes in light. To test the hypothesis that light is an environmental cue that Ascomycota use to coordinate growth, stress responses as well as to establish pathogenic or symbiotic relationships, the photoreceptor (PR) distribution in species from different ecological niches was analysed. The genomes of black fungi from phyllosphere and exposed solid surfaces contain multiple photoreceptors (PRs). The filamentous foliar plant pathogen Botrytis cinerea (Leotiomycetes) has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts. Rock-inhabiting Dothideo- and Eurotiomycetes including Knufia petricola possess equal numbers of PRs along with the same set of protective pigments. This similarity between black fungi from plant and rock surfaces suggests that photoperception and photoregulation are important for fungi that avoid loss of energy and nutrients through cooperation with phototrophs. T2 - European Fungal Secondary Metabolism Symposium CY - Hannover, Germany DA - 30.09.2019 KW - Fungi KW - Secondary metabolism KW - Light regulation KW - Pigments PY - 2019 AN - OPUS4-49638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Photoregulation in Plant- & Rock-associated Black Fungi N2 - Fungi that share light-flooded habitats with phototrophs may profit from excess photosynthetic products. But to cope with sunlight-associated stresses it is important for fungi to accurately sense and respond to changes in light. To test the hypothesis that light is an environmental cue that Ascomycota use to coordinate growth, stress responses as well as to establish pathogenic or symbiotic relationships, the photoreceptor (PR) distribution in species from different ecological niches was analysed. The genomes of black fungi from phyllosphere and exposed solid surfaces contain multiple photoreceptors (PRs). The filamentous foliar plant pathogen Botrytis cinerea (Leotiomycetes) has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts. Rock-inhabiting Dothideo- and Eurotiomycetes including Knufia petricola possess equal numbers of PRs along with the same set of protective pigments. This similarity between black fungi from plant and rock surfaces suggests that photoperception and photoregulation are important for fungi that avoid loss of energy and nutrients through cooperation with phototrophs. T2 - Scientific Colloquium at the Department of Genetics, University of Seville CY - Seville, Spain DA - 24.10.2019 KW - Light sensing KW - Knufia petricola KW - Botrytis cinerea PY - 2019 AN - OPUS4-49637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Rock-EATING FUNGI - Genetic Dive into the Biology of the Microcolonial Black Fungus Knufia petricola N2 - Microcolonial black fungi are a group of ascomycetes that exhibit high stress tolerance, yeast‑like growth and constitutive melanin formation. They dominate a range of hostile natural and man‑made environments, from desert rocks and salterns to dishwashers, roofs and solar panels. Due to their slow growth and a lack of genetic tools, the underlying mechanisms of black fungi’s phenotypic traits have remained largely unexplored. We chose to address this gap by genetically engineering the rock‑inhabiting fungus Knufia petricola (Eurotiomycetes, Chaetothyriales), a species that exhibits all characteristics of black fungi. The state‑of‑the‑art genetic toolkit, together with the annotated genome sequence of strain A95, firmly established K. petricola as a model for exploring microcolonial black fungi. T2 - VAAM-Jahrestagung 2021 CY - Online meeting DA - 18.03.2021 KW - Fungus KW - Genetics KW - Marble PY - 2021 AN - OPUS4-52496 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Erdmann, Eileen A. A1 - Nitsche, Sarah A1 - Gerrits, Ruben A1 - Heeger, Felix A1 - Gorbushina, Anna T1 - Genetic engineering of black fungi: lessons learned from Knufia petricola N2 - The exponential rise in the number of fungal genomes sequenced by next-generation sequencing techniques makes it necessary to increase efforts to correctly annotate and assign gene functions. There are two possibilities to explore a genome and its gene functions. The hypothesis-based method proves the function of already existing gene/allele candidates by targeted mutagenesis - so called reverse genetics. The basis of forward genetics approaches is the random mutagenesis of the genome, followed by screening of obtained mutants for the phenotype of interest, and identification of the mutated genes in the respective mutants. This strategy is hypothesis-generating, means it is necessary to verify the relationship between the detected mutations and the observed phenotype by targeted mutagenesis of the identified gene. We developed a toolbox for editing the genome of the rock inhabitant Knufia petricola [Eurotiomycetes, Chaetothyriales] that allows the study of the phenotypic characteristics of black fungi such as the regulation of pigment synthesis, general stress responses, oligotrophy, and the unusual modes of cell division by advanced reverse and forward genetics approaches. The toolbox includes the annotated genome sequence of strain A95, efficient strategies for CRISPR/Cas9-based genome editing and live-cell imaging using genetically encoded fluorescent proteins, as well as protocols for -omics approaches and for simulation of mineral weathering. A forward genetics approach using transposon mutagenesis is currently developed for identifying essential genes. The established protocols and knowledge gained from K. petricola form a starting point for making other fungi from extreme environments accessible to genetic manipulation. T2 - IUBMB Focused Meeting on Extremophilic Fungi (FUN-EX) CY - Ljubljana, Slovenia DA - 19.09.2023 KW - Fungus KW - Extremotolerance KW - Genetics KW - Model organism PY - 2023 AN - OPUS4-58424 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Brandhorst, Antonia A1 - Catanzaro, Ilaria A1 - Nitsche, Sarah A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Gorbushina, Anna T1 - Versatile DHN melanin – spotlight on its function in microcolonial black fungi N2 - Dihydroxynaphthalene (DHN) melanin is produced by diverse Ascomycetes via slightly differing biosynthetic routes. The polyketide synthases (PKS) release the heptaketide YWA1, the hexaketide AT4HN or the pentaketide T4HN. The first two products are deacetylated by ‘yellowish-green’ hydrolases to T4HN, and T4HN is further converted by a core set of enzymes to DHN. Final polymerization steps are accomplished by multicopper oxidases. DHN melanogenesis is often regulated in a spatial and temporal fashion resulting e.g., in melanized reproduction and survival structures of the foliar plant pathogen Botrytis cinerea (Schumacher 2016, Mol Microbiol). In contrast, a polyphyletic group of Ascomycetes (microcolonial fungi/ black yeasts) dwelling in hostile habitats such as bare rock surfaces in hot and cold deserts, exhibits constitutive melanogenesis. Here, DHN melanin builds a protective layer around all vegetative cells thus contributing to the survival of diverse environmental stresses even without specialized reproduction structures. For studying the relevance of constitutive DHN melanogenesis for tolerance of abiotic and biotic stresses, adhesion to substrates and subsequent damage of colonized surfaces, the rock-inhabiting fungus Knufia petricola was chosen as gene functions in this fungus can be studied by CRISPR/Cas9-based genome editing. The putative melanogenic genes were identified in the genome of K. petricola, deleted to confirm their involvement in DHN melanogenesis and co-expressed in Saccharomyces cerevisiae for reconstruction of the synthesis pathway. Phenotypes of DHN-deficient mutants are studied. Here, we will discuss the role of the DHN melanin layer on the outer cell wall in tolerating UV irradiation. T2 - Annual conference 2023 of the Association for General and Applied Microbiology CY - Göttingen, Germany DA - 10.09.2023 KW - Pigment KW - UV radiation KW - Tolerance PY - 2023 AN - OPUS4-58425 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Gorbushina, Anna A. T1 - How does light affect rock-inhabiting fungi? N2 - Sunlight is an almost unavoidable environmental cue and plays a fundamental role in the biology of pro- and eukaryotic organisms. To cope with sunlight-associated stresses e.g., high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses, it is important for organisms to accurately sense and respond to changes in light. The benefits of light are obvious for green organisms such as cyanobacteria, algae and plants which use light as an energy source (photosynthesis). Less apparent are other light-dependent processes such as light-driven DNA repair by photolyases (photoreactivation) or ion pumping by microbial opsins. Fungi that can share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess many proteins for absorbing UV/blue, green, red and far-red light, produce the black 1,8 dihydroxynaphthalene (DHN) melanin and orange-red carotenoids, and may live in multispecies biofilms. Here, we are addressing the question to which extent constitutive pigment formation (melanin and carotenoids) and responses mediated by the stress-activated mitogen-activated protein (MAP) kinase contribute to the observed light (UV-B) tolerance of K. petricola. T2 - 32nd Fungal Genetics Conference CY - Pacific Grove, CA, USA DA - 12.03.2024 KW - Knufia petricola KW - Black fungi KW - Light-induced stress PY - 2024 AN - OPUS4-59732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Looking through the eyes of fungi: from photoperception to photoresponses and beyond N2 - Sunlight is an almost unavoidable environmental cue and plays a fundamental role in the biology of pro- and eukaryotic organisms. To cope with sunlight-associated stresses e.g., high temperatures, UV radiation, accumulation of reactive oxygen species, desiccation, and osmotic stress, it is important for organisms to accurately sense and respond to changes in light. The benefits of light are obvious for green organisms such as cyanobacteria, algae and plants which use light as an energy source (photosynthesis). Fungi that can share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. Examples are the plant pathogen Botrytis cinerea, the gray mold fungus, and the rock inhabitant Knufia petricola, a microcolonial black fungus which forms multispecies biofilms with bacteria and algae. T2 - 20th Symposium of the Research Training Group on Bioactive Peptides – The colorful tree of life CY - Berlin, Germany DA - 23.01.2024 KW - Black fungi KW - Melanin KW - Stress tolerance PY - 2024 AN - OPUS4-59543 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Brandhorst, Antonia A1 - Nitsche, Sarah A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Gorbushina, Anna T1 - The roles of DHN melanin and the stress-activated MAP kinase in the rock inhabitant Knufia petricola N2 - Black fungi/yeasts exhibit high stress tolerance, yeast‑like or meristematic growth, and constitutive 1,8-dihydroxynaphthalene (DHN) melanin formation. Due to their slow growth, robust cell walls and the lack of sexual cycles and genetic tools, the underlying mechanisms of their phenotypic traits have remained largely unexplored. Using recently developed genetic tools, it is now possible to manipulate the genome of the rock-inhabiting model fungus Knufia petricola. Thus, gene functions and the cell biology of black fungi can be studied using CRISPR/Cas9-based genome editing and live-cell imaging with genetically encoded fluorescent proteins. Here, we are addressing the question to which extent constitutive pigment formation (melanin and carotenoids) and responses mediated by the stress-activated mitogen-activated protein (MAP) kinase contribute to the observed extremotolerance of K. petricola. The mutations of pks1, phs1 and both genes result in melanin-free (pink), carotenoid-free (black) and pigment-free (white) strains, respectively. The other putative melanogenic genes were identified in the genome, deleted to confirm their involvement in DHN melanogenesis and co-expressed in Saccharomyces cerevisiae for reconstruction of the synthesis pathway. Sak1 encoding the stress-activated MAP kinase was deleted in the wild-type and different pigment-deficient backgrounds. Growth of the obtained single, double and triple deletion mutants was tested by droplet tests on media supplemented with different stress-inducing agents. The Δsak1 mutants show slightly reduced growth rates even without environmental pressure and are hypersensitive to different stresses: e.g. osmotic, oxidative, membrane, pH and heat stress. Melanin-free Δsak1 mutants are more sensitive than black Δsak1 mutants to some but not all stress conditions, suggesting that melanin and the SAK1 pathway have complementary roles in protecting K. petricola from stress. T2 - 16th European Conference on Fungal Genetics CY - Innsbruck, Austria DA - 05.03.2023 KW - Black fungus KW - Extremotolerance KW - Pigments PY - 2023 AN - OPUS4-57147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Biocide resistance risk assessment N2 - This presentation details the current status of biocide resistance risk assessment. T2 - Risk assessment of biocide and antibiotic resistance CY - Online meeting DA - 09.03.2022 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Standardization KW - Biocides KW - Risk assessment PY - 2022 UR - https://www.gu.se/en/biocide/risk-assessment-of-biocide-and-antibiotic-resistance AN - OPUS4-56235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Resistenzen von Bakterien gegen Biozide – Evolution, Mechanismen und Methoden N2 - Diese Präsentation gibt einen Überblick über die Aktivitäten zum Thema Biozidresistenz an der BAM. T2 - Life Science Nord - Online-Update Hygiene und Infektionsprävention CY - Online meeting DA - 14.06.2022 KW - Antimikrobielle Resistenz KW - Antmikrobielle Oberflächen KW - Standardisierung KW - Biozide KW - Risikobewertung PY - 2022 UR - https://vimeo.com/722198443 AN - OPUS4-56236 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Biocides As Drivers For Antimicrobial Resistance Evolution In The Environment N2 - Antimicrobial resistance (AMR) is a global health problem with the environment being an important compartment for the evolution, selection and transmission of AMR. These processes are impacted by pollution with antibiotics. However, biocides used as disinfectants and material preservatives are major pollutants by far excceding the market for antibiotics in terms of mass. Our work shows that biocides have the potential to affect evolutionary processes towards AMR by increasing the rates of de-novo mutation and conjugation. These effects depend on the species and biocidal substance. Importantly, chlorhexidine and quaternary ammonium compounds (QACs) affect rates of mutation and conjugation at environmentally relevant concentrations in E. coli. Moreover, our results show a connection between the RpoS-mediated general stress and the RecA-linked SOS response with increased rates of mutation and conjugation, but not for all biocides. Furthermore, our work highlights the potential of biocides to contribute to selection and transmission of AMR. We show that the application of biocides, especially QAC disinfectants, leads to the rapid evolution of tolerance (i.e. increased survival) in adaptive laboratory evolution (ALE) experiments. The evolved tolerant strains have a selective advantage in the presence of environmentally-relevant concentrations of antibiotics, which could lead to the stabilization of biocide tolerance in environments where biocides and antibiotics co-occur (e.g. wastewater, animal stables). ALE experiments with biocide tolerant strains indicate a decreased evolvability of resistance to antibiotics. Taken together, our work shows the importance of assessing the contribution of biocides on evolution, selection and transmission of AMR in the environment. T2 - 6th Environmental Dimension of Antibiotic Resistance (EDAR6) CY - Gothenburg, Sweden DA - 22.09.2022 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Biofilms KW - Biocides KW - Risk assessment PY - 2022 AN - OPUS4-56262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Biocide Resistance - Road to Risk Assessment N2 - This presentation details the current status of biocide resistance risk assessment and provides a roadmap for future activities. T2 - OECD, 6th Meeting of the Working Party on Biocides CY - Paris, France DA - 28.09.2022 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Standardization KW - Biocides KW - Risk assessment PY - 2022 AN - OPUS4-56263 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - BIOCIDE N2 - This presentation gives an overview about the BIOCIDE project performed with the Aquatic Pollutants joint call. T2 - Aquatic Pollutants TransNet workshop CY - Online meeting DA - 09.11.2022 KW - Antimicrobial resistance KW - Bacteria KW - Biofilms KW - Biocides KW - Risk assessment KW - Wastewater PY - 2022 AN - OPUS4-56265 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Selection of resistance by antimicrobials used in coatings N2 - Antimicrobial surfaces have broad use in multiple settings including touch surfaces in hospitals, implanted devices, or consumer products. Their aim is to support existing hygiene procedures, and to help combat the increasing threat of antimicrobial resistance. However, concerns have been raised over the potential selection pressure exerted by such surfaces, which might drive the evolution and spread of antimicrobial resistance. In my presentation, I will highlight the risks and knowledge gaps associated with resistance on antimicrobial surfaces by different processes including evolution by de novo mutations and horizontal gene transfer, and species sorting of inherently resistant bacteria dispersed onto antimicrobial surfaces. The latter process has the potential to select for antibiotic resistance via cross-resistance between traits that confer resistance to both the antimicrobial surface coating and antibiotics. Conditions in which antibiotics and antimicrobial coatings are present simultaneously (e.g. implants) will lead to more complex interactions that can either result in the selection for or against antibiotic resistance. We mapped these interactions between several antimicrobials and antibiotics on growth and selection of Pseudomonas aeruginosa. We find prevalent physiological (i.e. synergy and antagonism) and evolutionary (i.e. cross-resistance and collateral sensitivity) combination effects. Understanding these interactions opens the door to tailor therapeutic interventions to select against resistance. In additions, we need new methods and translational studies that investigate resistance development to antimicrobial surfaces under realistic conditions. Therefore, I will present recent developments in our lab on the development of such a method based on existing efficacy standards. T2 - 2021 Fall Meeting of the European Materials Research Society (E-MRS) CY - Online meeting DA - 20.09.2021 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Biofilms KW - Biocides PY - 2021 AN - OPUS4-53645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Physiological and evolutionary consequences of exposing Pseudomonas aeruginosa to biocide-antibiotic combinations N2 - Antimicrobials can exert specific physiological effects when used in combination that are different from those when applied alone. These effects include physiological effects (i.e. synergy, antagonism and suppression) as well as evolutionary effects on the selection of resistant strains (i.e. cross-resistance and collateral sensitivity). While combination effects have been extensively mapped for antibiotic-antibiotic combinations, the combination effects of antibiotics with antimicrobials used as biocides or antiseptics have not been systematically investigated. Here, we investigated the physiological and evolutionary consequences of combinations of antibiotics (meropenem, gentamicin and ciprofloxacin) and substances used as biocides or antiseptics (octenidine, benzalkonium chloride, cetrimonium bromide, chlorhexidine, povidone-iodine, silver) on growth and selection of Pseudomonas aeruginosa. We find prevalent physiological combination effects with synergy occurring 6 times and antagonism occurring 10 times. The effects are specific to the antibiotic-biocide combination with meropenem showing a tendency for antagonism with biocides (6 of 7), while gentamicin has a tendency for synergy (5 of 7). A particular strong antagonism is apparent for the meropenem-chlorhexidine combination, for which we conducted an in-depth study on the underlying molecular mechanism using RNASeq. Moreover, we find widespread effects of the biocide-antibiotic combinations on selection of P. aeruginosa strains resistant to the antibiotics, including cross-resistance and collateral sensitivity. In conclusion, antibiotics and biocides or antiseptics exert physiological and evolutionary combination effects on the pathogen P. aeruginosa. These effects have consequences for the efficacy of both types of substances and for the selection of antimicrobial resistant strains in clinical applications with combined exposure (e.g. wound care, coated biomaterials). T2 - Antimicrobial Resistance in Biofilms and on Biomaterials CY - Online meeting DA - 10.06.2021 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Biofilms PY - 2021 AN - OPUS4-53162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Resistance evolution towards biocides and antimicrobial surfaces N2 - Biocides, including disinfectants and antimicrobial surfaces (AMCs), are important to prevent the spread of pathogens and antimicrobial resistant bacteria via surfaces. However, concerns have been raised about the evolution and selection of resistance against disinfectants and AMCs. In turn, resistance against disinfectants and AMCs can be associated to antibiotic resistance due to cross-resistance and co-resistance. We need to understand the mechanisms and risks of disinfectants and AMCs for resistance and cross-resistance evolution to optimize their application and safeguard their long-term efficacy. We used adaptive laboratory evolution (ALE) experiments based on repeated exposure of bacteria to disinfectants. Our results show that repeated disinfection of E. coli with benzalkonium chloride in suspension results in a 2000-fold increase in survival within 5 exposure cycles. Adaption is linked to the initial presence of persister cells highly tolerant to benzalkonium chloride. We used the same approach to develop standardizable ALE experiments to determine resistance evolution to AMCs. The results highlight rapid adaptation of E. coli and P. aeruginosa towards copper surfaces. Moreover, there are multiple situations in the clinic or in the environment in which biocides and antibiotics co-occur and in which combination effects can shape their antimicrobial activity or their selective effects. Our work with P. aeruginosa shows prevalent combination effects of biocides and antibiotics, ranging from synergy to antagonism and resulting in the selection for or against antibiotic resistant strains. The combination effects are dependent on the biofilm mode-of-growth, manifesting in apparent differences in the structural arrangement of antibiotic sensitive and resistant strains in biofilms exposed to combinations. Furthermore, biocides affect rates of mutation and horizontal gene transfer, thereby having a potential facilitating effect on resistance evolution. Taken together, our work shows that the role of biocides as potential drivers of resistance evolution and selection deserves further study and regulative action. T2 - Eurobiofilms 2022 CY - Palma, Spain DA - 31.08.2022 KW - Antimicrobial resistance KW - Bacteria KW - Biofilms KW - Biocides KW - Antimicrobial surfaces PY - 2022 AN - OPUS4-55608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Phenotypic diversity in microbial metabolism and antimicrobial resistance N2 - Most microorganisms live in environments where nutrients are limited and fluctuate over time. Cells respond to nutrient fluctuations by sensing and adapting their physiological state. Recent studies suggest phenotypic heterogeneity in isogenic populations as an alternative strategy in fluctuating environments, where a subpopulation of cells express a function that allows growth under conditions that might arise in the future. It is unknown how environmental factors such as nutrient limitation shape phenotypic heterogeneity in metabolism and whether this allows cells to respond to nutrient fluctuations. Here, we show that substrate limitation increases phenotypic heterogeneity in metabolism, and this heterogeneity allows cells to cope with substrate fluctuations. We subjected the N2-fixing bacterium Klebsiella oxytoca to different levels of substrate limitation and substrate shifts, and obtained time-resolved single-cell measurements of metabolic activities using nanometre-scale secondary ion mass spectrometry (NanoSIMS). We found that the level of NH4+ limitation shapes phenotypic heterogeneity in N2 fixation. In turn, the N2 fixation rate of single cells during NH4+ limitation correlates positively with their growth rate after a shift to NH4+ depletion, experimentally demonstrating the benefit of heterogeneity. The results indicate that phenotypic heterogeneity is a general solution to two important ecological challenges - nutrient limitation and fluctuations - that many microorganisms face. Currently, we use NanoSIMS to develop a new approach that defines functionally-relevant, phenotypic biodiversity in microbial systems. In the last part of my presentation, I will highlight why the concept of phenotypic diversity is relevant for the understanding of antimicrobial resistance. T2 - Berlin Seminar for Resistance Research at FU Berlin Veterinary Medicine CY - Berlin, Germany DA - 01.03.2018 KW - Antimicrobial Resistance KW - Metabolism KW - Phenotypic diversity PY - 2018 AN - OPUS4-44597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Single-cell trait-based biodiversity in microbial communities and its link to ecosystem functioning in a stratified lake N2 - A fundamental question in ecology is how biodiversity affects ecosystem function. Biodiversity is commonly estimated based on genetic variation. We investigated a new approach that defines and measures biodiversity in complex microbial communities. We used the variation in multiple functionally-relevant, phenotypic traits measured in parallel in single cells as a metric for microbial phenotypic diversity. We studied phenotypic diversity and ecosystem functioning throughout different photosynthetic layers dominated by divergent microbial communities in the gradient of Lago di Cadagno. We determined genetic diversity by 16S and 18S amplicon sequencing and bulk ecosystem functioning (photosynthesis). In addition, we determined phenotypic diversity using single-cell technologies such as nanometer-scale secondary ion mass spectrometry (NanoSIMS) correlated with confocal laser scanning microscopy (CLSM) and scanning flow-cytometry. We measured functional trait variation between individuals in 13CO2 fixation, 15NH4+ uptake, and variation in physio-morphological cell traits, such as cell size, shape, and auto-fluorescence for various pigments related to photosynthesis. We used the distances between individuals in a multidimensional trait space to derive phenotypic trait-based diversity indices, such as trait richness, trait evenness, and trait divergence. We find that phenotypic trait divergence associates with ecosystem functioning, whereas genetic diversity does not. Including activity-based, single-cell phenotypic measurements with NanoSIMS provided an additional accuracy to the trait-based diversity assessment and allowed us to formulate hypotheses on the mechanisms that shape the correlation between phenotypic diversity and eco-system function. Together, our results show that phenotypic diversity is a meaningful concept to measure microbial biodiversity and associate it with ecosystem functioning. T2 - 8th Congress of European Microbiologists - FEMS 2019 CY - Glasgow, UK DA - 07.11.2019 KW - NanoSIMS KW - Biodiversity PY - 2019 AN - OPUS4-49077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Phenotypic diversity in microbial metabolism and antimicrobial resistance N2 - Phenotypic dicersty can emerge in microbial metabolic activties and in persistence against antimicrobials. In this talk, I present two examples of phenotypic heterogeneity and discuss how they might be related. T2 - Workshop on Bacterial adaptation to antimicrobials: environmental, evolutionary and mechanistic aspects CY - FU Berlin, Germany DA - 17.04.2018 KW - Antimicrobial resistance KW - Metabolism KW - Phenotypic diversity PY - 2018 AN - OPUS4-46271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -