TY - CONF A1 - Kjaervik, Marit A1 - Dietrich, P. A1 - Thissen, A. A1 - Schwibbert, Karin A1 - Unger, Wolfgang T1 - Investigations of biofilms in various conditions by near-ambient pressure XPS N2 - X-ray photoelectron spectroscopy (XPS) provides elemental and chemical information from the outermost ~10 nm of the sample surface. This is in the same order of magnitude as the thickness of the outer bacterial membrane of gram-negative bacteria, as well as outer membrane molecules as exopolysaccharides and lipopolysaccharides, commonly attached to the cell surface. With the development of near-ambient pressure (NAP)-XPS, bacteria can be analysed with minimal sample preparation. EnviroESCA is a laboratory based NAP-XPS instrument, equipped with a monochromated Al Kα radiation source and a differentially pumped energy analyser connected to an exchangeable sample environment. It allows for measurements in various gas-atmospheres, including water vapor, which makes it possible to characterise bacteria and other biological samples close to their natural, hydrated state. Artificial model-biofilms of exopolysaccharides, planktonic Pseudomonas Fluorescens and biofilms of Escherichia Coli have been characterised in hydrated and dried state. High-resolution XPS-spectra from carbon, oxygen, nitrogen and phosphorous can be assigned to carbohydrates, lipids and proteins in general agreement with literature. Especially the carbon 1s peak is of interest. A series of measurements of an E. coli biofilm from 11 mbar in humid environment to 1 mbar air reveal changes in the C1s peak, which suggests that the bacterial surface undergo substantial Change. T2 - BAM PhD-retreat CY - Warnemünde, Germany DA - 28.09.2018 KW - Biofilms KW - E. coli KW - NAP-XPS PY - 2018 AN - OPUS4-46132 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, Paola T1 - Archaeometric analysis of Coptic inks N2 - We try to get as closer as possible to the ink composition, given that we have to work with non-invasive techniqes and on very degraded supports. T2 - Summer School in Coptic Literature CY - Hamburg, Centre for study Manuscript cultures, Germany DA - 17-09-2018 KW - Ink KW - Archaeometry PY - 2018 AN - OPUS4-46133 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Phenotypic diversity in microbial metabolism and antimicrobial resistance N2 - Phenotypic dicersty can emerge in microbial metabolic activties and in persistence against antimicrobials. In this talk, I present two examples of phenotypic heterogeneity and discuss how they might be related. T2 - Workshop on Bacterial adaptation to antimicrobials: environmental, evolutionary and mechanistic aspects CY - FU Berlin, Germany DA - 17.04.2018 KW - Antimicrobial resistance KW - Metabolism KW - Phenotypic diversity PY - 2018 AN - OPUS4-46271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Resistance selection on antimicrobial surfaces N2 - Antimicrobial surfaces are widely used to reduce the number of bacteria residing in the indoor environment. In this talk, I discuss the risk how these surfaces can lead to the selection of antimicrobial resistant bacteria. T2 - Cost action workshop Amici - Antimicrobial Coatings Applied in Healthcare Settings – Efficacy Testing CY - BAM Unter den Eichen, Berlin, Germany DA - 07.06.2018 KW - Antimicrobial resistance KW - Antimicrobial surfaces KW - Cross-resistance PY - 2018 AN - OPUS4-46272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Single-cell trait-based biodiversity in microbial communities N2 - A fundamental question in ecology is how biodiversity affects ecosystem function. Biodiversity is commonly estimated based on genetic variation. We investigated a new approach that defines and measures biodiversity in complex microbial communities. We used the variation in multiple functionally-relevant, phenotypic traits measured in parallel in single cells as a metric for microbial phenotypic diversity. We studied phenotypic diversity and ecosystem functioning throughout different photosynthetic layers dominated by divergent microbial communities in the gradient of Lago di Cadagno. We determined genetic diversity by 16S and 18S amplicon sequencing and bulk ecosystem functioning (photosynthesis). In addition, we determined phenotypic diversity using single-cell technologies such as nanometer-scale secondary ion mass spectrometry (NanoSIMS) correlated with confocal laser scanning microscopy (CLSM) and scanning flow-cytometry. We measured functional trait variation between individuals in 13CO2 fixation, 15NH4+ uptake, and variation in physio-morphological cell traits, such as cell size, shape, and auto-fluorescence for various pigments related to photosynthesis. We used the distances between individuals in a multidimensional trait space to derive phenotypic trait-based diversity indices, such as trait richness, trait evenness, and trait divergence. We find that phenotypic trait divergence associates with ecosystem functioning, whereas genetic diversity does not. Including activity-based, single-cell phenotypic measurements with NanoSIMS provided an additional accuracy to the trait-based diversity assessment and allowed us to formulate hypotheses on the mechanisms that shape the correlation between phenotypic diversity and eco-system function. Together, our results show that phenotypic diversity is a meaningful concept to measure microbial biodiversity and associate it with ecosystem functioning. T2 - 17th International Symposium on Microbial Ecology (ISME 17) CY - Leipzig, Germany DA - 12.08.2018 KW - Trait-based ecology KW - Phenotypic diversity KW - Lake Cadagno PY - 2018 AN - OPUS4-46273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Landsberger, B. A1 - Frauendorf, H. A1 - Adler, C. A1 - Plarre, Rüdiger T1 - Capability and limitation of anoxic treatments in museum collections protection N2 - Without precaution, insects may cause serious damage to Museum collections. Quarantine of potentially infested objects can be logistically challenging. Anoxia under controlled nitrogen atmosphere is a most compatible but also time-consuming method to eradicate insect pests in all kinds of different materials. Treatment results are usually effected by duration, temperature, humidity and residual oxygen content. During a two-year research project, 34 relevant pest insect species of all developmental stages were tested in several different materials (wood, paper, wool) to monitor treatment success and to determine optimum treatment parameters. Duration of Treatment ranged from one to three weeks at temperatures of 20 - 27 °C. As expected, results showed significant differences in mortality among tested species. Highest tolerance of hypoxic conditions was found in older larvae of Hylotrupes bajulus. However, this species is an unlikely museum pest. Anobiids and other wood boring beetles are more often an issue related to cultural heritage. Tested imbedding materials in general had no mortality lowering influence. A combination of three weeks exposure time at up to 0.5 % residual oxygen and at 24 °C and 50 % RH is recommended for infested artefacts. T2 - 12th International Working Conference on Stored Product Protection (IWCSPP) CY - Berlin, Germany DA - 07.10.2018 KW - Anoxia KW - Nitrogen KW - Cultural Heritage KW - Hylotrupes bajulus PY - 2018 AN - OPUS4-46255 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin A1 - Oberender, Christof A1 - Dosch, Klaus T1 - Ressourceneffizienz bewerten - Ansätze im VDI N2 - Vorstellung von methodischen Grundlagen für eine Ressourceneffizienzanalyse T2 - 3. Fachkonferenz "Stärkung des Einsatzes von mineralischen Recycling-Baustoffen" CY - Potsdam, Germany DA - 05.03.2018 KW - Ressourceneffizienz PY - 2018 AN - OPUS4-46683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kuhlbusch, T. A1 - Schmidt, Alexandra A1 - Bresch, Harald A1 - Kämpf, K. A1 - Bachmann, V. A1 - Völker, D. A1 - Schwirn, K. T1 - Test guideline on particle size and size distribution of manufactured nanomaterials N2 - The particle size distribution is considered the most relevant information for nanoscale property identification and material characterization. The current OECD test guideline on particle size and size distribution (TG 110) is not applicable to ‘nano-sized’ objects. In this project we thus develop a new OECD test guideline for the measurement of the size and size distribution of particles and fibers with at least one dimension in the range of 1 - 1000 nm. A fiber is defined as an object having an aspect ratio of length/diameter l/d >3. The width and length of each fiber should be measured concurrently. In order to measure the particle size distributions, many techniques are available. 9 methods for particles and 2 methods for fibres have been tested in a prevalidation study and appropriate methods will be compared in an interlaboratory round robin test starting in February 2019. T2 - Expertenaustausch Nanocluster und Malta-Initiative CY - Vienna, Austria DA - 30.10.2018 KW - Nanopartikel KW - Nano KW - Nanomaterial KW - Nano particle KW - Test guideline PY - 2018 AN - OPUS4-46671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Aktueller Stand der Mantelverordnung N2 - Übersicht über Hintergrund, Inhalt und aktuellen Stand der Mantelverordnung. T2 - Baustoffseminar in Weimar - Aktuelles aus der Welt der Gesteinskörnungen CY - Weimar, Germany DA - 10.04.2018 KW - Mantelverordnung PY - 2018 AN - OPUS4-46672 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Alexandra A1 - Bresch, Harald T1 - OECD test guideline on particle size and size distribution: Comparability of measurement results N2 - OECD-Prüfrichtlinien werden weltweit für regulatorische Zwecke angewandt, da sie eine harmonisierte und über internationale Ringversuche validierte Vorschrift zur Analyse vorgeben. Die bestehende Prüfrichtlinie TG 110 zur Größencharakterisierung von Partikeln und Fasern ist für viele Methoden und Materialklassen nicht geeignet, weswegen es Bedarf an einer Neuentwicklung gibt. Im Fokus der neuen TG steht die reproduzierbare und vergleichbare Anwendung von Methoden zur Bestimmung von Partikelgröße sowie Größenverteilung annährend sphärischer und faserförmiger Nanomaterialien im Bereich 1-1000 nm. Berücksichtigt werden die häufig angewandten Methoden zur Größencharakterisierung mit ihren unterschiedlichen physikalisch-technischen Limitierungen und die Bestimmung unterschiedlicher Durchmesser (hydrodynamischer, Feret…). Weiterhin sind materialspezifische Einflüsse durch die Partikel sowie das Messmedium zu berücksichtigen. Jede der Methoden soll unter Berücksichtigung von ISO-Standards und den materialspezifischen Limitierungen in der neuen Prüfrichtlinie beschrieben und über einen Ringversuch validiert werden. T2 - BAM BfR Workshop CY - Berlin, Germany DA - 21.03.2019 KW - OECD KW - Nanoparticle KW - Particle Size KW - Nano KW - Characterization PY - 2019 AN - OPUS4-47633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussionen aus dem Fachbeirat der BAM N2 - Vor nun 30 Jahren im Jahre 1989 wurde die erste Zulassung für eine Kunststoffdichtungsbahn von der BAM auf der Grundlage des „Niedersächsischen Dichtungserlasses“ erteilt. Vor ungefähr 10 Jahren wurde die BAM mit dem Erscheinen der Deponieverordnung (DepV) mit der Zulassung von Geokunststoffen, Polymeren und Dichtungskontrollsystemen beauftragt. Wir möchten dies zum Anlass nehmen, an dieser Stelle den viele ehrenamtlichen Experten des Fachbeirats und seiner Arbeitsgruppen für ihren Einsatz und die Unterstützung zu danken. Darüber hinaus soll über aktuelle Arbeitsthemen und Entwicklungen im Fachbeirat berichtet werden. So soll in einer Sondersitzung des Fachbeirats über die Entlassung aus der Nachsorgephase beim Einsatz von Geokunststoffprodukten in Böschungen diskutiert werden. Es ist geplant, in einer Unterarbeitsgruppe eine Sitzung über die Fremdüber¬wachung in der Produktion abzuhalten. Darüber hinaus werden Änderungen in den Zulassungsrichtlinien für Kunststoff Dichtungsbahnen und Kunststoff Dränelemente kurz vorgestellt. In der Zwischenzeit wurde auch die abschließende Zulassungsrichtlinie für Geogitter verabschiedet. Neue Fragestellungen sind hier entstanden. Unter welchen Voraussetzungen können Geogitter in Zwischenabdichtungen eingesetzt werden. Bisher können diese Produkte formal nur in Oberflächenabdichtungen eingesetzt werden. Auch auf diese beiden Themen soll im Folgenden in Kürze eingegangen werden. T2 - 15. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 05.03.2019 KW - Geogitter KW - Deponie KW - Kunststoffdichtungsbahnen PY - 2019 AN - OPUS4-47492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hamann, Christopher A1 - Spanka, M. A1 - Stolle, Dirk A1 - Adam, Christian A1 - Auer, G. T1 - Rückgewinnung von Zink aus Stahlwerksstäuben durch gemeinsame Behandlung mit chloridhaltigen Reststoffen N2 - Dieser Vortrag beschreibt die Entwicklung eines neuen chemischen Verfahrens, das in einem Kooperationsprojekt zwischen der Bundesanstalt für Materialforschung und -prüfung (BAM) und der Ferro Duo GmbH entwickelt wird. Mit dem entwickelten Verfahren soll es ermöglicht werden, schwermetallhaltige Filterstäube und -schlämme, die als Abfälle während der Produktion von Roheisen und Rohstahl anfallen und die derzeit größtenteils deponiert werden, zu recyceln und die darin enthaltenen Wertstoffe (v.a. Eisen, Kohlenstoff und Zink) wieder in den Rohstoffkreislauf zurückzugeben. Dies wird durch eine Chlorierung der in den Filterstäuben und -schlämmen enthaltenen Schwermetalloxiden erreicht, die bei Temperaturen zwischen 650 und 1100 °C in Form von Schwermetallchloriden verdampft und so selektiv separiert werden. Erste experimentelle Ergebnisse zeigen, dass die Gehalte an Schwermetallen wie Zink, Blei und Cadmium um bis zu 99,7% reduziert werden können und die thermochemisch behandelten Filterstäube und -schlämme durch das Verfahren in sekundäre Rohstoffe für die Roheisenproduktion umgewandelt werden können. T2 - Berliner Recycling- und Rohstoffkonferenz 2019 CY - Berlin, Germany DA - 11.03.2019 KW - Zink KW - Recycling KW - Gichtgasschlamm KW - Elektroofenstaub KW - Ressourcenrückgewinnung PY - 2019 AN - OPUS4-47524 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöller, Renate T1 - Scientific analysis of the Humboldt fragments N2 - The presented Humboldt Codices are from the early colonial period of Mexico and originate from different localities 1. typical indigen colors and mixtures: cochineal (red), indigo (blue and green), carbon (black), mangle, zacatlaxcalli, organic (brown, yellow)- critical! 2. colonial influence: iron gall ink for writing 3. single fragments belong together: are cut (fragments IX-XII), from Mizquahuala distributed (VII, XIII, XIV, [XV]) (VII, XIII in Mexico, XIV in Paris) T2 - Workshop: Manuscripta Americana: Aufarbeitung einer Sammlung; Staatsbibliothek zu Berlin - PK CY - Berlin, Germany DA - 14. Februar 2019 KW - Humboldt Codices KW - XRF-, VIS- FTIR-spectroscopy KW - Dyes PY - 2019 AN - OPUS4-47589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schliephake, H. A1 - Adam, Christian T1 - CFK-Abfälle als Primärkohleersatz Im Lichtbogenofen bei der Stahlerzeugung N2 - CFK-Abfälle werden trotz der bestehenden Verfahren zur Rückgewinnung der Carbonfasern zukünftig vermehrt anfallen. Für diese Abfälle wird nach technischen Lösungen der energetischen oder stofflichen Verwertung gesucht. Eine Möglichkeit ist die Nutzung der CFK-Abfälle als Primärkohleersatz im Lichtbogenofen bei der Stahlherstellung. T2 - 3. Fachtagung Composite Recycling & LCA CY - Stuttgart, Germany DA - 20.02.2019 KW - Carbonfaser KW - CFK PY - 2019 AN - OPUS4-47438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noeller, Renate A1 - Danielewski, Angelika A1 - Giel, Robert A1 - Hahn, Oliver A1 - Overgaauw, Everadus T1 - Analysis of the codices `Fragmens de Peinture hiéroglyphique Aztèques, deposés à la Bibliotheque royale de Berlin´ represented on plate 36 in `Vues des Cordillères et Monuments des Peuples Indigènes de l`Amerique, Voyage de Humboldt et Bonpland´ N2 - The mayor part of the Berlin collection `Manuscripta Americana´ consists of documents compiled by Alexander von Humboldt. The diversity of the written fragments and their shape presume few accordance concerning purpose, place or time of production. Even before the papers came to Berlin, manuscripts were copied, divided and collected by famous scholars also in Mexico. Back in Europe, Humboldt visited further collections and published the detected hieroglyphic writings altogether with cultural objects and landscapes in the book `Vues des Cordillères et Monuments des Peuples Indigènes de l`Amerique, voyage de Humboldt et Bonpland´, labelled corresponding to the cultural background. By scientific and culture historical analyses, the Humboldt codices are revised and related to each other and others. In especial, the compilation of fragments shown on plate 36 in the book is looked at more closely. Whereas most of the plates represent only one sheet of painted amate paper, here segments with details of seven fragments are put together. It is tried to comprehend why these pieces are on one plate. To find out a common feature of the documents, their content and represented form are compared. A correlation between some pieces is obvious and thus is also expected in the manufacture of the codices, in the kind of material used. For this the inks and colors are determined by scientific analysis including XRF-, Raman-, FTIR- and VIS- spectroscopy. Special material is detected and related to results of former analysis of codices written during the colonial period of America. Herewith a clear cultural assignment of the manuscripts is performed. A relation of the fragments represented on plate 36 among each other and to other codices of the collection Manuscripta Americana in Berlin is discussed. Also, if the manuscripts are unique `originals´ or represent fragments of documents, whose corresponding pieces maybe found- in the best case- incorporated in other collections. We detected, that at least two of them can be put into relation to similar manuscripts deposited in Mexico. Further material analysis should clarify, if the corresponding pieces are identical- from one document, or if one of them is a copy. Herewith an approximation to authenticity features and history is issued. T2 - 42nd International Symposium on Archaeometry ISA 2018 CY - Merida, Yucatan, Mexico DA - 20.05.2018 KW - Vues des Cordillères KW - VIS KW - Humboldt Codices KW - XRF KW - FTIR KW - Raman PY - 2018 AN - OPUS4-47554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noeller, Renate A1 - Danielewski, A. A1 - Giel, R. A1 - Hahn, Oliver A1 - Owergaauw, E. T1 - Análisis del material de los Códices Humboldt N2 - Los Códices Humboldt, que proceden de la época colonial de Mexico, muestran: 1. colores indígenas típicos y sus mezclas: cochinilla (rojo), índigo/ Azul Maya (azul y verde), carbón (negro), zacatlaxcalli, mangle, colores orgánicos (amarillo) 2. influencia colonial: tinta hierro- gálico para escribir 3. fragmentos distribuidos y cortados: partes singulares forman parte de otros fragmentos dentro de la colección (y en otras colecciones?) T2 - Seminario: Estudio comparativo de los manuscritos de la colección Manuscripta Americana (Berlín y Cracovia) con los manuscritos del Archivo General de la Nación y Museo Nacional de Antropología (México); Instituto de Investigaciones Estéticas; Universidad Nacional Autónoma de México (UNAM) CY - Mexico City, Mexico DA - 05.11.2018 KW - Humboldt Codices KW - XRF-, FTIR-, VIS-espectroscopía PY - 2018 AN - OPUS4-47560 LA - spa AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noeller, Renate A1 - Danielewski, A. A1 - Giel, R. A1 - Hahn, Oliver A1 - Overgaauw, E. T1 - Análisis de los Códices HUMBOLDT Relacionado con fragmentos en méxico: de Mizquiahualla N2 - Los códices de Mizquiahualla MsAmer1 frag VII, XIII (XIV, XV) muestran: - colores indigenes: cochinilla (rojo), indigo (verde, azul), carbón (negro), zacatlaxcalli (amarillo) - papel indigen (amate) - pintura con líneas perfil en negro, pintado antes y después de la coloración - influencía colonial: escritura en tinta hierro- gálica (1571, 1569) T2 - Seminario: Estudio comparativo de los manuscritos de la colección Manuscripta Americana (Berlín y Cracovia) con los manuscritos del Archivo General de la Nación y Museo Nacional de Antropología (México) CY - INSTITUTO DE INVESTIGACIONES ESTÉTICAS, UNAM, Mexico DA - 05.11.2018 KW - Humboldt Codices KW - FTIR-, XRF-, VIS- espectroscopia PY - 2018 AN - OPUS4-47561 LA - spa AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noeller, Renate A1 - Danielewski, A. A1 - Giel, R. A1 - Hahn, Oliver A1 - Overgaauw, E. T1 - Analysis of `Manuscripta Americana´ related to fragments in Mexico: Codex Techialoyan N2 - Techialoyan/ Central Mexico MsAmer7 shows limited colors: ochre (yellow, brown red, rose) indigo (blue, green, greyblue+?) cerussite + chalk (white) organic ink for writing (brown) T2 - Seminario: Estudio comparativo de los manuscritos de la colección Manuscripta Americana (Berlín y Cracovia) con los manuscritos del Archivo General de la Nación y Museo Nacional de Antropología (México) CY - INSTITUTO DE INVESTIGACIONES ESTÉTICAS, UNAM, Mexico DF DA - 05.11.2018 KW - XRF-, VIS- spectroscopy KW - Manuscripta Americana, Techialoyan PY - 2018 AN - OPUS4-47562 LA - spa AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Overview on the EMPIR Project "AEROMET" N2 - Overview on the ongoing EU EMPIR Project "AEROMET" Aerosol Metrology for Atmospheric Science and Air Quality, Overview on preliminary resuilts in Workpackages 3 "Calibration of MPSS and CPCs" and 4 "Quantifying airborne particle compositions in the field" T2 - Meeting des ISO TC24/SC4, Joint session of Working Groups 9 "Single particle light interaction methods" and 12 "Electrical mobility and number concentration analysis for aerosol particles" CY - Graz, Austria DA - 11.04.2019 KW - Ambient air pollution KW - EU EMPIR KW - Chemical analysis KW - Total reflection X-ray spectroscopy KW - Airborne Particles PY - 2019 AN - OPUS4-47820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Hermann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC. T2 - VAAM- Annual Conference 2019 of the Association for General and Applied Microbiology CY - Mainz, Germany DA - 17.03.2019 KW - HI-Tension KW - MIC KW - Methanogens KW - Corrosion KW - Sulfate reducing bacteria PY - 2019 AN - OPUS4-47739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Themenfeld Projekt MIC Mikrobiell beeinflusste Korrosion N2 - Mikrobiell beeinflusste Korrosion (MIC) ist ein Themenfeldprojekt innerhalb der BAM. Das Spektrum der Materialien und der Organismen ist ernorm. In dem Themenfeldprojekt MIC wurden ausgewählte Bereiche tiefergehend untersucht. In der Präsentation werden die Hauptschwerpunkte dargestellt. T2 - Beirat Material CY - Berlin, Germany DA - 03.04.2019 KW - MIC KW - Kraftstoffabbau KW - Kraftstoffbehälter KW - Gesteinskorrosion KW - Metallkorrosion KW - HI-Tension PY - 2019 AN - OPUS4-47740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Schadstoffe im Innenbereich – Fachhandel-, Baumarkt-, Bioprodukte: Nicht deklarierte Emissionen versus Verwendbarkeit - Eine Qual der Wahl! N2 - Es lässt sich feststellen, dass eine Vielzahl unterschiedlicher flüchtiger organischer Verbindungen aus Bauprodukten freigesetzt werden kann. Hierbei gibt es in den meisten Bauproduktgruppen sowohl emissionsarme als auch emissionsreiche Produkte. Manche Verbindungen sind produktgruppenspezifisch; so werden beispielsweise Siloxane aus Silikondichtmassen freigesetzt, andere Verbindungen sind eher unspezifisch wie Formaldehyd und Essigsäure, die aber in unterschiedlichen Konzentrationen aus einer Vielzahl von Produkten abgegeben werden und zu den am häufigsten emittierten Verbindungen zählen. Es ist darauf hinzuweisen, dass VOC-Analytik und Gerüche im Allgemeinen keinen Zusammenhang zeigen. Gerade bei modernen, dichten Bauten mit geringem natürlichem Luftwechsel sind hohe Schadstoffkonzentrationen zu erwarten, wenn nicht emissionsarme Materialien und Produkte zum Einsatz kommen. T2 - AIBAU 2019 CY - Aachen, Germany DA - 08.04.2019 KW - Innenraum KW - Luftschadstoffe KW - Bauprodukte KW - Emission PY - 2019 AN - OPUS4-47924 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin A1 - Herrmann, Annett T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC.zeige weniger T2 - Dechema CY - Berlin, Germany DA - 09.04.2019 KW - Corrosion KW - Corrosion products KW - Methanogens KW - Sulfate reducing bacteria KW - Flow-system KW - Environmental simulation PY - 2019 AN - OPUS4-47853 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Loose, Florian T1 - CF Pyro: Impressions of Applying Carbon Fibers at Semi-Industrial Scale as Reductant in Pyrometallurgy N2 - The increasing use of carbon fiber reinforced polymers (CFRP), as lightweight materials essential for the transformation, demands for a safe treatment option of carbon fiber (CF) containing waste streams. Because of their low reactivity towards oxidation processes, CF can neither be treated in a conventional nor hazardous waste incineration plant. Even the extremely high temperature in a cement rotary kiln does not lead to full conversion. To increase the sustainability of CF, other processes need to be investigated. Opening other reaction pathways, using CF waste streams as secondary resource in pyrometallurgy to replace fossil carbon, can be a solution for a safe and sustainable treatment. After first small scale experiments, CF containing waste streams were used as reductant in a semi-industrial scale electric arc furnace (EAF). First results and impressions are presented. T2 - Meeting mit Projektpartner GMH CY - Online meeting DA - 02.03.2023 KW - Cabonfasern KW - CFK KW - Recycling PY - 2023 AN - OPUS4-58090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Loose, Florian T1 - CF Pyro: Safe Treatment of CFRP Waste for a Sustainable Future N2 - The increasing use of carbon fiber reinforced polymers (CFRP), as lightweight materials essential for the transformation, demands for a safe treatment option of carbon fiber (CF) containing waste streams. Because of their low reactivity towards oxidation processes, CF can neither be treated in a conventional nor hazardous waste incineration plant. Even the extremely high temperature in a cement rotary kiln does not lead to full conversion. To increase the sustainability of CF, other processes need to be investigated. Opening other reaction pathways, using CF waste streams as secondary resource in pyrometallurgy to replace fossil carbon, can be a solution for a safe and sustainable treatment. To support the industrial application, experiments on different scales were conducted. Here, results of thermochemical investigations, reactivity studies, crucible experiments and pilot plat trials are reported. T2 - CU Projektforum CY - Online meeting DA - 19.01.2023 KW - Cabonfasern KW - CFK KW - Recycling PY - 2023 AN - OPUS4-58091 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Loose, Florian A1 - Schlögel, Kai T1 - CF Pyro Stofflich energetische Verwertung von carbonfaserhaltigen Abfällen in der Pyrometallurgie 4. Sitzung des projektbegleitenden Ausschusses N2 - Obwohl der Leichtbau mit carbonfaserverstärkten Kunststoffen (CFK) einen wichtigen Beitrag zum Klimaschutz und zur Ressourceneffizienz liefert, stellt der wachsende Abfallstrom von aktuell 62 kt/a eine große Herausforderung dar. Weil die Produktion von Carbonfasern (CF) überwiegend auf fossilen Rohstoffen basiert und sehr energieintensiv ist, werden nachhaltige Recyclinglösungen dringend benötigt. Hier geben wir einen Überblick über aktuelle Recyclingprozesse und diskutieren deren Limitierungen. Darüber hinaus zeigen wir eine Möglichkeit zur sicheren chemischen Nutzung von CF-haltigen Reststoffen auf, die nicht zur Wiederverwertung geeignet sind. Das Projekt CF Pyro untersucht deren Einsatz als Sekundärrohstoff in der Pyrometallurgie und setzt besondere Schwerpunkte bei der Reaktivität von CF, der Prozessstabilität und der Vermeidung von Emissionen gesundheitsschädlicher WHO-Fasern. Neben der Vorstellung von wichtigen fundamentalen experimentellen Erkenntnissen wird ihre Bedeutung für den Wandel zum zirkulären Wirtschaften diskutiert. T2 - 4. PA Meeting CY - Online meeting DA - 26.06.2023 KW - Cabonfasern KW - CFK KW - Recycling PY - 2023 AN - OPUS4-58092 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Loose, Florian T1 - Das Technologietransfer-Programm Leichtbau N2 - Neben Ressourceneinsparungen in der Produktion sorgen moderne Leichtbauwerkstoffe und -technologien für Energieeinsparungen in der Nutzungsphase. Auf diese Weise sowie als Enabler für eine Vielzahl an Zukunftstechnologien, wie zum Beispiel erneuerbare Energien, Elektromobilität und die Wasserstoffwirtschaft, ist Leichtbau fundamental für die Entkopplung des Wirtschaftswachstums vom Ressourcenverbrauch, die Erreichung der Ziele des Green Deals und eine Nachhaltige Zukunft. Um marktnahe Potentiale für Klima- und Ressourcenschutz vollständig zu heben und Herausforderungen wie die Kreislauffähigkeit im Leichtbau aktiv zu adressieren, fördert das BMWK marktnahe Innovationen im Leichtbau mit den Technologietransfer-Programm Leichtbau (TTP LB) Auch für die BAM bietet das TTP LB interessante Möglichkeiten, Forschungsvorhaben umzusetzen. Derzeit werden vier Projekte mit BAM-Beteiligung gefördert. In diesem Webinar stellen wir Ihnen die gesamte Breite des Leichtbaus vor und zeigen Ihnen damit direkte Anknüpfungspunkte zu Ihrer Forschung. Dafür wird das TTP LB vorgestellt, werden wertvolle Einblicke zur Antragstellung gegeben und der Weg zum Erfolg wird am Beispiel des BAM-Projektes SmartWeld skizziert. Neben der Erläuterung von technischen Details und formalen Anforderungen des Förderprogramms möchten wir ebenfalls versuchen, einen kleinen Ausblick auf mögliche zukünftige Entwicklungen zu geben. T2 - Webinar TTP LB CY - Online meeting DA - 11.01.2023 KW - Leichtbau KW - Forschungsförderung KW - Technologietransfer PY - 2023 AN - OPUS4-58093 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker A1 - Kalinka, Gerhard A1 - Loose, Florian T1 - Carbon fibre composites exemplarily research at BAM N2 - Lightweighting as a cross-cutting technology contributes significantly to achieve the European Green Deal goals. Based on, but not limited to, advanced materials and production technologies, the demand for natural resources and CO2 emmissions are reduced by lightweighting during production, as well as use phase. Therefore, lightweighting is a crucial transformation technology assisting in decoupling economic growth from resource consumption. In this manner, lightweighting contributes significantly as a key technology of relevance for many industrial sectors such as energy, mobility, and infrastructure, towards resource efficiency, climate action and economic strength, as well as a resilient Europe. To strengthen international partnerships, addressing global issues of today at the edge of science with high performance lightweight material based on carbon fibers, an overview about the BAM expertise in carbon fiber reinforced materials is given. T2 - Meeting KCarbon CY - Berlin, Germany DA - 15.06.2023 KW - Lightweighting KW - Carbon Fibers KW - Recycling KW - Push-out Test KW - multi scale testing PY - 2023 AN - OPUS4-58094 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimmer, Christoph A1 - Strzelczyk, Rebecca A1 - Richter, Matthias A1 - Musyanovych, Anna A1 - Horn, Wolfgang T1 - Development, application and measurement uncertainty of emission reference materials N2 - Volatile organic compounds (VOCs) emitted by furniture and building materials can cause health issues. For an improvement of indoor air quality low emitting materials should be used. Quality assurance and –control (QA/QC) measures require an emission reference material (ERM) with a predictable emission rate of VOCs. The idea is to use porous materials as ERM, which store the VOCs inside their pores and emit them constantly. T2 - Webinar Metrology for Indoor Air Quality Reference materials for QA/QC of the emission test chamber procedure CY - Online meeting DA - 11.04.2024 KW - Emission reference materials KW - Indoor air quality KW - Materials emissions test KW - VOC PY - 2024 AN - OPUS4-59963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimmer, Christoph A1 - Richter, Matthias A1 - Musyanovych, Anna A1 - Strzelczyk, Rebecca A1 - Horn, Wolfgang T1 - Preparation of novel emission reference materials: μ-capsules & impregnated porous materials N2 - Volatile organic compounds (VOCs) emitted by furniture and building materials can cause health issues. For an improvement of indoor air quality low emitting materials should be used. Quality assurance and –control (QA/QC) measures require an emission reference material (ERM) with a predictable emission rate of VOCs. The idea is to use porous materials as ERM, which store the VOCs inside their pores and emit them constantly. T2 - WORKSHOP: METROLOGY FOR INDOOR AIR QUALITY CY - Mol, Belgium DA - 18.10.2023 KW - Emission reference materials KW - Indoor air quality KW - Materials emissions test KW - VOC PY - 2023 AN - OPUS4-59961 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Emission Testing for Indoor Products N2 - The chemical emissions from products are tested by means of emission test chambers under defined conditions (climate, loading, air change rate). The standard method for the determination of volatile organic compounds (VOC) is the sampling onto Tenax-tubes followed by thermal desorption (TDS) and gas chromatography-mass spectrometry (GC-MS) analysis. The EU-LCI list includes some very volatile organic compounds (VVOC) and some VOC for which there are limitations when using the standard method. For VVOC additional sampling is required using stronger absorbers like Carbotrap or multi-bed adsorption tubes. The analysis of VVOC also requires a different GC oven program and a different column for the separation. For the determination of formaldehyde and other low boiling aldehydes (e.g. acetaldehyde, acetone, propanal, propenal) DNPH-cartridges are used which are extracted with acetonitrile followed by liquid chromatography (HPLC-UV) analysis. The derivatisation of propenal and other unsaturated aldehydes (e.g. 2-butenal) with DNPH might lead to lower findings due to incomplete derivatization and forming of by-products. For a better quantification of acetic acid the use of ion chromatography (IC) is recommended because the analysis of acetic acid with the standard method (TDS) leads to lower findings due to break through during sampling. The use of ion chromatography for the analysis of organic acids requires a third sampling technique. The acids are adsorbed onto silica-gel and extracted with water. T2 - ISESISIAQ 2019 CY - Kaunas, Lituania DA - 18.08.2019 KW - Indoor Air Quality KW - Emission Testing KW - Indoor Products KW - VOC Emission KW - Construction Products PY - 2019 AN - OPUS4-49406 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Krom, I. A1 - Heikens, D. A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Baldan, A. T1 - CRMs for (semi-)VOCs in sorbent tubes N2 - EN 16516 sets the test method and requirements for the determination of emissions of Volatile Organic Compounds (VOCs) from building materials into indoor air. To address the quality control requirements for the class of semi-VOCs (SVOCs), VSL developed gaseous reference materials. A novel home-made dynamic gas mixture preparation system, operating according to ISO 6145-4 (continuous injection method), has recently been developed and validated. Thanks to the stable temperature control up to 100 oC, the system can prevent condensation of the SVOCs in air at indoor air concentration levels. The in-situ obtained SVOC gas standards can be sampled in sorbent tubes to obtain SVOC transfer standards. A study was performed to determine the optimal sorbent material and storage conditions. This study will be presented together with the results of the 2018 Round Robin test for emission test chamber measurements organised by BAM. Using the novel system, VSL prepared transfer standards with known amounts of VOCs and SVOCs for participants to evaluate their analytical performance. T2 - Emissions and Odours from Materials CY - Brussels, Belgium DA - 07.10.2019 KW - CRM KW - VOC transfer standards KW - Round robin test KW - Material emissions testing PY - 2019 AN - OPUS4-49423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Standardisierte Formaldehyd- (und VOC-) Messungen bei Holzwerkstoffen zur Einspeisung der Daten in Normungsprozesse N2 - UBA und BAM schlagen die Durchführung der Prüfkammermessungen bei 23 °C und 50% relativer Luftfeuchte, einer Beladung von 1,8 m²/m³ und einem Luftwechsel von 0,5 pro Stunde vor. Diese Parameter orientieren sich an der EN 16516, die als zukünftige „Referenznorm“ zu betrachten ist. Die Schmalflächenversiegelung ist auch zukünftig wie in der EN 717-1 beschrieben vorzunehmen. Nach 28 Tagen wird der Mittelwert einer Doppelbestimmung als Endkonzentration („entsprechend der Ausgleichskonzentration“) berechnet. Alternativ dazu kann die Prüfung vorzeitig abgebrochen werden, wenn an 5 Messtagen der Prüfung eine Formaldehydkonzentration von 0,1 ppm nicht überschritten wird. Prüfungen nach der EN 717-1 sollen weiterhin gleichberechtigt möglich sein. Ergebnisse von Messungen, die nach der EN 717-1 ermittelt wurden, sind mit dem Faktor 2,0 zu multiplizieren. Abgeleitete Verfahren wie z.B. das Gasanalyseverfahren sollen weiterhin möglich sein. Das Perforatorverfahren entfällt hier, da eine allgemeine für alle Holzwerkstoffe gültige Korrelationen nicht existiert. Die entsprechenden Änderungen sind in der vom BMUB veröffentlichten „Bekanntmachung analytischer Verfahren für Probenahmen und Untersuchungen für die im Anhang der Chemikalien-Verbotsverordnung genannten Stoffe und Stoffgruppen“ entsprechend zu ändern. T2 - UFOPLAN Workshop CY - Berlin, Germany DA - 22.06.2018 KW - EN 717-1 KW - Prüfkammer KW - Formaldehyd KW - EN 16516 PY - 2018 AN - OPUS4-45632 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pollakowski-Herrmann, Beatrix A1 - Seeger, Stefan A1 - Gross, A. A1 - Kayser, Y. A1 - Osan, J. A1 - Stabile, L. A1 - Beckhoff, B. T1 - Quantitative elemental analysis of ambient aerosol particles using portable TXRF N2 - A reliable analysis of aerosol particle is curial for enforcing EU air quality regulations to protect human health, and for research on climate change effects [1]. Although metrics such as PM10 and PM2.5 are currently in use, the level of uncertainty of aerosol metrics is too high and the traceability is insufficient. Within the AEROMET project [2] procedures are developed aiming at reducing the uncertainties of particle mass, size, and number concentration measurements including the characterization of regulated components in airborne particles. Here, we present an approach how to improve the uncertainties of the particle mass by mobile total reflection x-ray fluorescence (TXRF) analysis. The combination of TXRF and aerosols sampling techniques supported by reference-free synchrotron radiation-based XRF enables a quantitative real-time analysis of particle mass. During in-field campaigns, the procedure was tested, monitoring the size dependent mass concentrations of specific elements in ambient aerosols under dynamic conditions. This approach allows a direct time and size-resolved analysis without laborious digestion steps and a reduced risk of contamination. Aerosol particles were sampled in a 13-stage DLPI impactor on acrylic discs. TXRF analysis was performed on-site with the transportable spectrometer S2 PICOFOX (Bruker Nano GmbH). The TXRF quantification was based on internal standardization. At moderate air pollution levels (PM10 20 µg/m³) sampling times of less than 2 hours were enough to detect elements in different particle size bins. The on-site approach and the high sensitivity of TXRF enables the observation of rather quick changes in the quantity and distribution of elements in an ambient aerosol on the day of sampling. The analysis of the morning and afternoon sampling shifts reveals the occurrence of the elements Fe, Ca and Si in different size bins as well as their temporal change in respective mass concentrations over the day while the distributions of several other elements remain unchanged. T2 - 11th International Conference on “Instrumental Methods of Analysis” CY - Ioannina, Greece DA - 22.09.2019 KW - Air quality KW - Novel sample preparation techniques KW - Analytical chemistry KW - Metals PY - 2019 AN - OPUS4-49249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Instruments for Fine and Ultrafine Particle Emission Characterization N2 - An overview on instruments and methods for the measurement and chemical characterization of particulate emissions from local sources is presented T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - Aerosol spectroscopy KW - Particulate emission KW - Chemical analysis KW - Total reflection X-ray spectroscopy KW - Calibration PY - 2019 AN - OPUS4-47816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - Selection of low emittiong material for the construction of display cases based on the BEMMA procedure N2 - Museums worldwide are equipped with different display cases. Exhibit display cases should protect cultural objects from dust as well as from mechanical and physical damage. To ensure a stable climate inside the display cases, a low air exchange rate is maintained. Typically air exchange rates are often smaller than 0.1 d 1, which can result in rising concentrations of potential harmful immissions inside of the display cases due to emissions from materials. Especially high concentrations of organic acids, which can emit from e.g. sealing materials, can produce damage of cultural objects. In 2012 BAM introduced a procedure witch is called: BEMMA-Scheme (Bewertung von Emissionen aus Materialien für Museumsausstattungen) which stands for: “Assessment of Emissions from Materials for Museum Equipment”. Micro chambers are used for VOC emission tests of display case construction materials, e.g. textiles, plastics, sealing material, coatings and others. Each sampling procedure is carried out in duplicate. Emissions like formic acid, acetic acid, formaldehyde and oximes are excluded and the sum of emissions of VVOCs, VOCs and SVOCs is limited. For a positive assessment all listed criteria must be fulfilled; otherwise the display construction material fails the BEMMA scheme. The BEMMA scheme is not a guarantee for an emission free display case, but a necessary requirement for the choice of suitable materials for emission and immission reduced display cases. T2 - Materials Testing Symposium CY - New York City, USA DA - 06.11.2019 KW - Museum KW - Emission KW - Dispay case KW - BEMMA KW - VOC PY - 2019 AN - OPUS4-49589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Jann, Oliver T1 - Formaldehydmessungen an Holzwerkstoffplatten N2 - Die von der BAM eingekauften Holzwerkstoffplatten (Verlegespanplatten, OSB, Multiplexplatten) verschiedener Hersteller zeigten teilweise hohe Formaldehyd-emissionen unter den Prüfbedingungen nach EN 16516, eine Spanplatte hielt den Grenzwert von 0,1 ppm selbst bei Prüfung nach DIN EN 717-1 nicht ein, dürfte also in Deutschland gar nicht in den Verkauf gelangen. Holzwerkstoffe, die unter den Prüfbedingungen der DIN EN 717-1 die Formaldehydklasse E1 einhalten, können insbesondere bei großflächigem Einsatz im Innenraum zu Überschreitungen des Richtwertes für die Innenraumluft führen. Zusätzlich zur Anpassung des Luftwechsels ist auch der Parameter Beladung bei einer Überarbeitung der Norm anzupassen. In der DIN EN 16516 werden produktspezifische (am Einsatz der Produkte orientierte) Beladungsfaktoren vorgegeben. Für den Einsatz von Holzwerkstoffplatten ergäben sich Beladungen von 0,4 (Boden oder Decke), 1,0 (Wände), 1,4 (Wände plus Boden oder Decke) und 1,8 m²/m³ (Wände, Boden und Decke). Um die realen Bedingungen in modernen Gebäuden abzubilden, ist deshalb eine Beladung von 1,8 m²/m³ für die Prüfkammermessung erforderlich. Hierbei ist darauf hinzuweisen, dass für die Beladung im Referenzraum Möbel nicht berücksichtigt wurden. Damit soll sichergestellt werden, dass die Einhaltung des Schutzniveaus bei realen Innenraumbedingungen auch unter den Randbedingungen eines niedrigen Luftwechsels sowie bei sommerlichen Bedingungen und heutigem Lüftungsverhalten der Menschen soweit wie möglich gewährleistet ist. T2 - 26. WaBoLu-Innenraumtage CY - Berlin, Germany DA - 20.05.2019 KW - Formaldehyd KW - Emissionsprüfkammer KW - DIN EN 16516 KW - DIN EN 717-1 PY - 2019 AN - OPUS4-48065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rudy T1 - Sylfuryldiflourid im Holzschutz N2 - Die Anwendung von Sulfuryldiflourid ist auf den bekämpfenden Holzschutz gegen Insekten beschränkt. Die Anwendung in Deutschland regelt die DIN 68800 Teil 4 und das europäische Biozidgesetz. Zur Erhaltung von Kulturgut ist dieses Begasungsmittel einzigartig. T2 - Seminar E.: Symposium zukünftige Verwendung von Sulfuryldifluorid CY - Hannover, Germany DA - 17.04.2024 KW - Holzschutz KW - Begasung KW - Regelwerk PY - 2024 AN - OPUS4-59917 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - Materialität von Musikhandschriften N2 - Die Bezeichnung „Tinte auf Papier“ bietet einen guten Einstieg in die Beschreibung der Materialität von Musikhandschriften; so haben sich zahlreiche Manuskripte erhalten, die mit Eisengallustinte auf Hadernpapier verfasst wurden. Das Papier besteht aus Fasern meist pflanzlicher Herkunft und wird durch Entwässerung einer Fasersuspension auf einem Sieb gebildet. Der Abdruck des Schöpfsiebes (die Papierstruktur) und ein vorhandenes Wasserzeichen bieten Anhaltspunkte für Provenienz und Datierung; daneben erlaubt die Analyse der Fasern, der Füllstoffe und der Leimung eine weitere Charakterisierung des Schriftträgers. Spätestens seit dem Mittelalter sind es Eisengallustinten, die das schwarze bis bräunliche Erscheinungsbild vieler Manuskripte auf Papier hervorrufen. Daneben lassen sich auch schwarze Rußtuschen oder farbige Auszeichnungstuschen nachweisen. Eisengallustinten werden durch Mischung einer eisenhaltigen Komponente mit Gerbstoffen hergestellt. Eisensulfat ist die am häufigsten genannte Eisen liefernde Zutat, daneben sind aber auch eisenhaltige Minerale, Nägel oder Rost denkbar. Die Gallussäure leitet sich ab aus den Galläpfeln, der krankhaften Veränderung einzelner Planzenteile verschiedener Eichenarten. Diese werden durch die Eiablage von Schlupfwespen hervorgerufen. Wie schon beim Papier ermöglicht der materialanalytische Nachweis charakteristischer Beimischungen oder Verunreinigungen innerhalb der Tinten die Beantwortung kulturhistorischer Fragestellungen – gemeint sind hier die Unterscheidung von Original und Korrektur oder die Sichtbarmachung späterer Ergänzungen. T2 - DFG-Rundgespraech zur Thermographie-Digitalisierung von Wasserzeichen in Musikhandschriften CY - Vienna, Austria DA - 23.10.2023 KW - Thermographie KW - Manuskripte KW - Wasserzeichen KW - Papier PY - 2023 AN - OPUS4-58798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Rühle, Bastian A1 - Bresch, Harald T1 - Competence Center nano@BAM Welcomes ISO/TC 229 Meeting in Berlin N2 - The Competence Center nano@BAM is presented. Examples directly related to the activities of the ISO Technical Committee TC 229 Nanotechnologies as well as BAM projects on nano reference measurement procedures, nano reference materials and nano reference data sets are showed. T2 - The 32nd ISO/TC 229 IEC/TC 113 JWG2 General Meeting CY - Berlin, Germany DA - 06.11.2023 KW - ISO/TC 229 Nanotechnologies KW - Nanoparticles KW - Nano@BAM KW - Reference materials KW - Reference data KW - Reference procedures PY - 2023 AN - OPUS4-58814 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian T1 - P-Rückgewinnungspflicht nach AbfKlärV - Betrachtungen zu Konzentrationen und Frachten N2 - Vortrag über die Regelungen der AbfKlärV bezüglich P-Rückgewinnung. Diskussion der Auswirkung einer konzentrationsbezogenen Grenze auf die Pflicht zur P-Rückgewinnung. Diskussion der nach AbfKlärV zulässigen analytischen Verfahren zur Bestimmung von P in Klärschlamm und Ableitung von Empfehlungen. Vorstellung der Ergebnisse eines Ringversuchs mit 28 Laboren. T2 - KlärschlammTage Würzburg CY - Würzburg, Germany DA - 23.05.2023 KW - Klärschlamm KW - P-Rückgewinnung KW - Ringversuch P-Gehalt in Klärschlamm PY - 2023 AN - OPUS4-57541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Schneider, Joachim A1 - Schraut, Katharina A1 - Algermissen, D. A1 - Ebert, D. A1 - Ehrenberg, A. A1 - Gronen, L. A1 - Feldrappe, V. T1 - Strategien für die Nutzung von Schlacken zukünftiger wasserstoffbasierter Stahlproduktionsrouten – Herstellung von Stahlwerksschlacke basierten Ausgangsstoffen für die Zementindustrie N2 - Die Europäische Kommission präsentierte am 11. Dezember 2019 den European Green Deal, ein Konzept mit dem Ziel, bis zum Jahr 2050 als erster Kontinent Klimaneutralität zu erreichen. Mit Inkrafttreten der Verordnung (EU) 2021/1119 des Europäischen Parlaments und des Europäischen Rates am 29. Juli 2021 zur Schaffung des Rahmens für die Verwirklichung der Klimaneutralität („Europäisches Klimagesetz“), ist dieses, sowie das Ziel der Reduzierung der Nettotreibhausgasemissionen um mindestens 55 % bis 2030 in der Gesetzgebung der Europäischen Union verankert. Die Stahlindustrie in der Europäischen Union mit ca. 57 Mio. t Nettotreibhausgasemissionen im Jahr 2020, die annähernd 2 % der Emissionen der Europäischen Union ausmachen (Inklusive Energie: 127 Mio. t; 4 %), bekennt sich zur erheblichen Reduzierung der CO2-Emissionen bis zum Jahr 2030 und zum Erreichen der Klimaneutralität bis zum Jahr 2050. Als Schlüsselwege zur Verwirklichung dieser Zielstellung hat sie zum einen Smart Carbon Usage (SCU) und zum anderen Carbon Direct Avoidance (CDA) in einer Roadmap formuliert. SCU umfasst CO2-reduzierende Maßnahmen in bestehenden Eisen- und Stahlproduktionsprozessen, Carbon Capture and Storage- (CCS) sowie Carbon Capture and Usage-Technologien (CCU). Wohingegen bei CDA CO2-Emissionen durch erneuerbare elektrische Energie sowie wasserstoffbasierte Reduktion des Eisenerzes gar nicht erst entstehen sollen. Der CDA-Weg, der voraussichtlich beschritten werden muss, um eine klimaneutrale Stahlproduktion zu erreichen [38], geht mit einer kostenintensiven Transformation der Stahlproduktion einher, die bereits von vielen Unternehmen der Stahlindustrie eingeleitet wurde und von der im Wesentlichen die beiden in Europa vorherrschenden Stahlproduktionsrouten Hochofen-Konverter-Route und Elektrolichtbogenofen-Route betroffen sind. Die CO2-Emissionen der Hochofen-Konverter-Route, von denen der überwiegende Anteil auf den Hochofen fällt, liegen laut einer für das Jahr 2015 erstellten Studie bei 1921 kg CO2/t Rohstahl inklusive der CO2-Last der Pellets als Einsatzmaterial sowie der Emissionen der nachgelagerten Stranggießanlagen und Walzwerke. Im Hochofen wird das Eisenerz durch Kohlenstoff (C) bzw. Kohlenstoffmonoxid (CO) – welche größtenteils aus dem Koks, der dem Hochofen zusammen mit dem Möller über die Gicht zugeführten wird, stammen – unter Entstehung von Roheisen und Kohlenstoffdioxid (CO2) reduziert. Das neben dem CO2 im Prozessgas enthaltene CO wird zum Beispiel zur Energiegewinnung in peripheren Prozessen ebenfalls unter Bildung von CO2 verbrannt. Zusätzlich zur Reduktion hat der Koks unter anderem physikalische Aufgaben, wie die Errichtung eines Stützgerüstes und die Gewährleistung der Permeabilität im Hochofenprozess. Somit ist eine vollkommene Substitution des Kokses zur Vermeidung der CO2-Emissionen im Hochofen nicht denkbar. Viele Strategien der Stahlunternehmen zum Erreichen der Klimaziele verfolgen daher den Wechsel von der Rohstahlproduktion aus der Hochofen-Konverter-Route hin zur Rohstahlproduktion im Elektrolichtbogenofen (EAF – Electric Arc Furnace) mit dem Einsatz von direkt reduziertem Eisen (Eisenschwamm, DRI – Direct Reduced Iron) aus vorgelagerten Direktreduktionsanlagen, die mit Wasserstoff (H2) als Reduktionsmittel betrieben werden können. Dabei ist die Elektrostahlerzeugung kein neuer Prozess und nimmt in der europäischen Union bereits jetzt einen Anteil von ca. 44 % der Rohstahlproduktion ein, jedoch überwiegend mit Schrott als Einsatzmaterial. Bei der Elektrostahlerzeugung mit Schrotteinsatz fallen laut der oben genannten Studie von Lüngen für das Jahr 20152 410 kg CO2-Emissionen pro Tonne Rohstahl an, von denen der Großteil auf die CO2-Last der fremd bezogenen elektrischen Energie zurückzuführen ist und daher nicht im Produktionsprozess selbst entsteht. Auch die Direktreduktion wird schon seit 1972 in der weltweit zweiten und bis heute in Westeuropa einzigen Direktreduktionsanlage in Hamburg betrieben. Während hier noch mit einem Reduktionsgas gearbeitet wird, das hauptsächlich aus einem aus Erdgas gewonnenen Wasserstoff-Kohlenstoffmonoxid-Gemisch besteht, liegt eine aktuelle Kernherausforderung in der Bereitstellung des in der Größenordnung der von der Transformation betroffenen Rohstahlproduktionskapazitäten notwendigen, mit erneuerbarer elektrischer Energie hergestellten Wasserstoffs. Wird zusätzlich der Strom für das Einschmelzen im Elektrolichtbogenofen aus erneuerbaren Quellen gewonnen und werden schließlich als Brennstoff verwendete Kohle und als Brennstoff verwendetes Erdgas durch CO2-neutrale Bio-Brennstoffe ersetzt, sind sowohl für den Einsatz von mit Wasserstoff reduziertem und auf Pellets ohne CO2-Last basiertem Eisenschwamm als auch für den Einsatz von Schrott CO2-Emissionen von jeweils nur 60 kg CO2/t Rohstahl erreichbar, was eine Reduktion der Emissionen, ausgehend von der Konverter-Hochofen-Route um 97 % und ausgehend von der Schrott-Elektrolichtbogenofen-Route um 85 % bedeuten würde. Der Betrieb von Elektrolichtbogenöfen macht die an den Standorten vorhandenen Konverter sowie die Infrastruktur für Behandlung und Transport des Roheisens überflüssig. Die fortwährende Nutzung dieser bestehenden Anlagenstruktur dient daher unter anderem als Motivation für die Entwicklung einer zweiten Transformationsstrategie, die einen sogenannten Einschmelzer (SAF – Submerged Arc Furnace) als der Direktreduktionsanlage nachgelagerten Prozess vorsieht, in dem wiederum Roheisen erschmolzen wird, das anschließend im Konverter zu Rohstahl veredelt wird. Die Transformation der Stahlindustrie beeinflusst einen weiteren CO2-intensiven Industriesektor, nämlich die Zementindustrie die verantwortlich ist für rund 4 % der CO2-Emissionen in der EU. Etwa zwei Drittel dieser Emissionen entfallen als Prozessemissionen auf die Entsäuerung des Rohstoffs Kalkstein (CaCO3), also auf die Abspaltung von CO2 unter Entstehung des für die Herstellung von Zementklinker notwendigen Branntkalks (CaO) als Zwischenstufe bei der Bildung der hydraulischen Phasen Tri- und Dicalciumsilikat. Als eines der fünf Themenfelder (5C-Ansatz: Clinker, Cement, Concrete, Construction, Carbonation), welche die europäische Zementindustrie entlang ihrer Wertschöpfungskette zum Erreichen der gesetzlichen Vorgaben der europäischen Union erarbeitet hat, umfasst das Feld "Cement" zum größten Teil die Reduzierung des Klinker-Zement-Faktors. Im Jahr 2017 betrug er 77 %, das heißt, dass 23 % des Klinkers durch alternative Materialien ersetzt wurden. Bis zum Jahr 2030 wird ein Faktor von 74 % und bis zum Jahr 2050 von 65 % angestrebt. Den größten Anteil an den Klinkersubstituten hat mit 33 % der Hüttensand aus der Stahlindustrie. Bei der Roheisenproduktion im Hochofen entsteht als Nebenprodukt Hochofenschlacke, die unter Zugabe von Schlackebildnern die Gangart des Möllers und mineralische Koksbestandteile abbindet, sowie weitere unerwünschte Begleitelemente wie Schwefel und Alkalien aufnimmt. Allein in Deutschland wurden im Jahr 2021 6,90 Mio. t – das entspricht 90 % der gesamten produzierten Hochofenschlacke – zu glasig erstarrtem Hüttensand granuliert. Dieser Hüttensand besitzt latent hydraulische Eigenschaften und wird daher seit mehr als 140 Jahren als Zementbestandteil eingesetzt, wodurch in Deutschland jährlich rund 4,5 Mio. t CO2-Emissionen eingespart werden. Alle Transformationsstrategien der Stahlindustrie beinhalten die notwendige Außerbetriebnahme der CO2-intensiven Hochöfen. Dies hat unter anderem zur Folge, dass die Hochofenschlacke als Nebenprodukt der Rohstahlerzeugung im Hochofen nicht mehr zur Verfügung stehen wird, wodurch die weitere Reduzierung des Klinker-Zement-Faktors erhebliche Zusatzmengen alternativer Materialien benötigen wird. Derzeit ist noch unklar, ob z.B. calcinierte Tone im benötigten Umfang erzeugt werden können. Der Fachbereich Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung der Bundesanstalt für Materialforschung und -prüfung (BAM) und das Institut für Baustoffforschung FEhS forschen zusammen mit Industriepartnern und weiteren Forschungseinrichtungen im Rahmen zweier Projekte in den Kooperationssphären der Stahl- und Zementindustrie, die zur Bewältigung dieser Herausforderungen beitragen. Im Projekt SlagCEM wird die Produktion eines hydraulischen Zementbestandteils durch Reduktion von Konverter- bzw. Linz-Donawitz-Schlacke (LDS) untersucht. Die mit den zusätzlich aufgenommen Lichtbogenofenkapazitäten steigenden Mengen an Elektrolichtbogenofenschlacke (EOS, engl. electric arc furnace slag, EAFS) werden im Projekt DRI-EOS behandelt, welches die Produktion eines latent hydraulischen Hüttensandsubstituts zum Ziel hat. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 12.06.2023 KW - Stahlwerksschlacke KW - Zementersatz PY - 2023 AN - OPUS4-57683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Einführung in die Mantelverordnung - Stand der Bundes-Bodenschutz- und Altlastenverordnung N2 - Einführung in die Mantelverordnung Stand der Bundes-Bodenschutz- und Altlastenverordnung, aktuelles zum Aufbau der MVO und zum Stand Anfang 2023 T2 - X. Baustoffseminar - Aktuelles zu Gesteinskörnungen CY - Bad Berka, Germany DA - 17.01.2023 KW - Mantelverordnung KW - Gesteinskörnungen KW - Wiederverwertung PY - 2023 AN - OPUS4-57798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sobisch, Lydia-Yasmin A1 - Schreiber, Frank T1 - Biocide resistance evolution of corrosion causing sulfate reducing bacteria N2 - SRB are environmentally and industrially important microorganisms. The disadvantage of their metabolic activity (e.g. sulfate reduction) results in the formation of toxic sulfide that leads to microbial influenced corrosion. SRB have been responsible for biocorrosion of ferrous metal. One of mitigation strategy is the use of biocides. However, it has been shown that various bacteria develop antimicrobial resistance due to excessive use of biocides. Thus, a deeper understanding of the evolution of biocide resistance of SRB is necessary. Three commonly used biocides, THPS, BAC, and GLUT were applied to investigate the susceptibility of Desulfovibrio alaskensis G20.The minimum inhibitory and bactericidal concentration and the killing kinetics of the three biocides was determined. These results will be used to conduct evolution experiments to determine the evolution of resistance towards biocides of SRBs. The outcome of this work can be helpful to improve the management of MIC treatments. T2 - Panel, Pitch & Popcorn by EUROMIC CY - Online meeting DA - 21.06.2021 KW - Biocide KW - Evolution KW - Mircobially influcenced corrosion KW - Sulfate reducing bacteria PY - 2021 AN - OPUS4-56940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver A1 - Golle, U. A1 - Wintermann, Carsten T1 - Original, Kopie, Fälschung? Multispektralanalyse von Bauhauszeichnungen N2 - Der Vortrag widmet sich der materialwissenschaftlichen Analyse von Zeichnungen einiger Bauhausschülerinnen und Bauhausschüler und legt besonderen Fokus auf die verwendeten Farbmittel. Die Objekte werden mit nicht-invasiven bildgebenden Verfahren untersucht, in dem die Wechselwirkung zwischen Röntgen-, sichtbarem und infraroten Licht und den Zeichnungen studiert wird. Dier Analysen liefern nicht nur generell Erkenntnisse über die Art und Zusammensetzung und damit das Alter der verwendeten Farbmittel. Durch die Auffindung von Vorzeichnungen, die Bestimmung von Überarbeitungen und Korrekturen werden Erkenntnisse über die Genese von Zeichnungen gewonnen. Auf der Basis dieser materialwissenschaftlichen Erkenntnisse werden die Begriffe Original, Kopie, Fälschung diskutiert. Da die nicht-invasiven Untersuchungen einen umfassenden Einblick in die Materialität der – überwiegend aus Papier bestehenden – Objekte erlauben, bilden sie die Grundlage für die Erstellung nachhaltiger Konservierungs- und Restaurierungskampagnen und deren dauerhaften Erhalt. T2 - Rahmenprogramm zur Ausstellung "Das Leben der Objekte. Farbe und Papier am Weimarer Bauhaus" CY - Weimar, Germany DA - 12.01.2023 KW - Bauhaus KW - Zerstörungsfreie Prüfung KW - Farbmittel PY - 2023 AN - OPUS4-56847 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - PFAS analytics and their relation to PFAS remediation N2 - Per- and polyfluoroalkyl substances (PFAS) are a large group of more than 10,000 anionic, cationic, zwitterionic or neutral organofluorine surfactants. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. While liquid chromatography tandem mass spectrometry (LC-MS/MS) is commonly used technique to characterize targeted PFAS in environmental samples, there are more than 10,000 different PFAS known, which have various headgroups and properties. Therefore, several analytical techniques are available to analyse various groups or pools of PFAS or “all” PFAS as a sum parameter. Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Previously, mechanochemical treatment of polychlorinated organic compounds in soils showed an efficient dechlorination. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GC-MS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well es the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - International workshop of CAR-PFAS (Consortium for analysis and remediation of per- and polyfluoroalkyl substances) Japan CY - Tokyo, Japan DA - 17.10.2023 KW - Mechanochemical treatment KW - Per- and Polyfluoroalkyl substances (PFAS) KW - XANES spectroscopy KW - Soil PY - 2023 AN - OPUS4-58609 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Wasserstofflagerung in unterirdischen geologischen Formationen und potenzielle Risiken durch Mikroorganismen N2 - Bei dem Vortrag werden die potentiellen mikrobiologischen Einflüsse im Falle der Lagerung von Wasserstofflagerung in unterirdischen geologischen Formationen vorgestellt, die Zusammenarbeit mit internen und auch externen Partnern. Der Fokus liegt dabei auf UGF; anaerobe Umgebungen, Sulfate reduzierenden Bakterien, methanogenen Archaea, weiterleitenden Systeme und die Kombination der Untersuchung abiotisch/biotische T2 - VDI-Schadensanalyse (49) CY - Würzburg, Germany DA - 17.10.2023 KW - MIC KW - Wasserstofflagerung KW - Unterirdische Speicher KW - Kontamination von H2 KW - H2-Abbau KW - Mikroorganismen KW - Biotische/abiotische Faktoren PY - 2023 AN - OPUS4-58645 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - It´s just a point of view – destructions and creations of cultural objects by artifact pests N2 - Woodworms, carpet beetles, clothes moths and termites are well known pests on artifacts of cultural importance. Lately also silverfish have gained importance. Protection of our cultural heritage for future generations is not a new task but the methods have changed. Conventional use of pesticides in the past has preserved precious objects up to the presence, which otherwise probably would have been lost over time due to the destruction by insects and microbes. However, several of the objects were contaminated with poisons in such a manner that they became unsafe to be handled and thus are useless for exhibitions or scientific studies. Today, the concept of Integrated Museum Pest Management (IMPM) provides guidance for non-residue treatments of infested objects, followed by save storage or display under pest free (or maximum pest reduced) environments. Inert fumigants, physical and biological control measure, precise monitoring, threshold evaluations and detailed knowledge of the pest`s biology are key elements within IMPM. Woodworms, clothes moths and termites, however, are not always considered as only pests. Some professionals have also used them to produce new pieces of art or for the installation of ephemeral displays. Under more or less controlled conditions, the insects´ destructive nature on wood or textiles has been turned around to a process of creation with aesthetic or philosophical messages. Destructive or creative - it just depends on the point of view! T2 - XII European Congress of Entomology CY - Heraklion, Greece DA - 16.10.23 KW - Museum Pests KW - Integrated Museum Pest Management (IMPM) KW - Cultural Entomology PY - 2023 AN - OPUS4-58651 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Resistance evolution towards biocides and antimicrobial surfaces N2 - This presentation describes our work at BAM on resistance evolution towards biocides and antimicrobial surfaces. T2 - Break biofilms workshop CY - Vienna, Austria DA - 16.01.2023 KW - Antimicrobial resistance KW - Bacteria KW - Biofilms KW - Biocides PY - 2023 AN - OPUS4-57857 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Die Entstehung von antimikrobiellen Resistenzen durch die Verwendung von Bioziden N2 - Dieser Vortrag gibt einen Überblick über die BAM und die Aktivitäten im Bereich Biozidresistenz. T2 - Berliner Hochschule für Technik Studiengang Biotechnologie CY - Berlin, Germany DA - 05.05.2023 KW - Antimikrobielle Resistenz KW - Antmikrobielle Oberflächen KW - Standardisierung PY - 2023 AN - OPUS4-57859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Bakterielle Resistenzen und Toleranzen gegen Desinfektionsmittel und antimikrobielle Oberflächen N2 - Dieser Vortrag beschreibt die Entstehung von bakteriellen Resistenzen und Toleranzen gegen Desinfektionsmittel und antimikrobielle Oberflächen. T2 - Fachtagung für Krankenhaushygiene der Deutschen Gesellschaft für Krankenhaushygiene CY - Essen, Germany DA - 12.05.2023 KW - Antimikrobielle Resistenz KW - Antmikrobielle Oberflächen KW - Standardisierung KW - Biozide PY - 2023 AN - OPUS4-57860 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aumont, Cedric A1 - McMahon, Dino Peter T1 - Harnessing near-chromosome level quality genomes to explore the evolution of termite immunity N2 - The phylogeny of the Blattodea boasts a wide degree of sociality spanning from solitary cockroaches to advanced ecosystem-dominating higher termite societies. The emergence of sociality in termites was associated with the acquisition of a diverse range of social structures. Previous work has found evidence for a caste-specific social defence system in termites leading to an immune system that may favour group over individual defence. While preliminary work suggests a correlation between social transitions and a reduction of immune gene family diversity, the lack of available high-quality termite genomes hampers complete knowledge of the true diversity of immune gene evolution across termite phylogeny. Here, we report on the sequencing and near-chromosome level assembly of 48 high-quality long-read-based genomes across major termite and cockroach sister-branch lineages. We investigate the diversity and evolutionary history of immune genes across genomes, focusing particular attention on correlations between immune gene evolution and transitions in sociality over termite phylogeny. T2 - Royal Entomological Society Annual Meeting - Ento23 CY - University of Exeter, Falmouth, UK DA - 05.09.2023 KW - Immune gene family KW - Termite phylogeny KW - Eusociality KW - Group defence PY - 2023 AN - OPUS4-58296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aumont, Cedric A1 - McMahon, Dino Peter T1 - Immune gene family diversity across insects and Blattodea N2 - Insecta is one of the most diverse phyla in the animal kingdom, with species living in all types of habitats encountering an even greater diversity of pathogens and parasites. Defence strategies against such harmful threats led to a variety of molecular mechanisms, ecological shifts, and genetic innovations. Gene families underlying the molecular basis of the immune responses have evolved within the boundaries given by the species ecology. Here, we explore the evolution of some emblematic immune gene families throughout the Insecta phylum shedding light on remarkable genetic events such as gene duplication or gene loss. We followed a workflow based on the Hidden Markov model to search for immune genes in 55 high-quality genomes of insects. We highlight the emergence of group defence in social species as an ecological shift that released selection pressure on immune gene families notably in Blattodea. Further, we draw attention to certain gene families and the link between their diversity and the specificities of the species’ microbiota. Overall, we report data on immune gene diversity in insects. T2 - International Conference for Blattodea Research CY - Münster, Germany DA - 03.04.2023 KW - Immune gene family KW - Genomics KW - Blattodea PY - 2023 AN - OPUS4-58298 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jiang, Shixiong A1 - McMahon, Dino Peter T1 - Adipokinetic hormones and their receptors in Blattodea: a comparative analysis N2 - Adipokinetic hormone (AKH) is a neuropeptide produced in the insect corpora cardiaca that plays an essential role in mobilizing carbohydrates and lipids from the fat body to the hemolymph. AKH acts by binding to a rhodopsin-like G protein-coupled receptor (GPCR), the adipokinetic hormone receptor (AKHR). In this study, we tackle AKH ligand and receptor gene evolution as well as the evolutionary origins of AKH gene paralogues from the order Blattodea (termites and cockroaches). Phylogenetic analyses of AKH precursor sequences point to an ancient AKH gene duplication event in the common ancestor of Blaberoidea, yielding a new group of putative decapeptides. In total, 16 different AKH peptides from 90 species were obtained. Two octapeptides and seven putatively novel decapeptides are predicted for the first time. AKH receptor (AKHRs) sequences from 18 species, spanning solitary cockroaches and subsocial woodroaches as well as lower and higher termites, were subsequently acquired using classical molecular methods and in silico approaches employing transcriptomic data. Aligned AKHR open reading frames revealed 7 highly conserved transmembrane regions, a typical arrangement for GPCRs. Phylogenetic analyses based on AKHR sequences support accepted relationships among termite and cockroach lineages to a large extent, while putative post-translational modification sites do not greatly differ between solitary and subsocial roaches and social termites. This study provides important information not only for AKH and AKHR functional research but also for further analyses interested in their development as potential candidates for biorational pest control agents against invasive termites and cockroaches. T2 - International Conference for Blattodea Research CY - Münster, Germany DA - 03.04.2023 KW - Adipokinetic hormone KW - Neuropeptide KW - Termite KW - Green pesticide KW - Adipokinetic hormone receptor PY - 2023 AN - OPUS4-58299 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Zum Spannungsrissverhalten von PE-HD Kunststoffdichtungsbahnen und zu aktuellen Themen aus dem Fachbeirat der BAM N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen im Zusammenhang mit der Zulassungsrichtlinie für KDB vorgestellt werden. Der aktuelle Stand der Diskussion im Zusammenhang mit den verwendeten Tensiden in Bezug auf die Spannungsrissprüfung und weiterer Prüfungen wird aufgezeigt. Änderungen der Fremdprüfung von sogenannten Sandschutzmatten, des Standards zur Qualitätsüberwachung (SQÜ) von Kunststoff Dränelementen (KDE) und der Anpassung der Formulierungen zum Überbau der in Abdichtungen verwendeten Produkte werden in Kürze aufgezeigt. T2 - Karlsruher Deponie- und Altlastenseminar 2023 CY - Karlsruhe, Germany DA - 18.10.2023 KW - Deponie KW - Kunststoffdichtungsbahn KW - Spannungsrissbeständigkeit PY - 2023 AN - OPUS4-58634 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan A1 - Bresch, Harald T1 - VAMAS Regional Report Germany N2 - Regional standardisation activities and how VAMAS can help in any way to promote activities are reported. Activities related to organisational updates, government initiatives/priorities (especially related to Materials), details of any strategy documents publicly available, networks within Germany and how we engage are presented. T2 - Versailles Project on Advanced Materials and Standards (VAMAS) 48th Steering Committee Meeting CY - New Delhi, India DA - 09.10.2023 KW - VAMAS KW - Standardisation PY - 2023 UR - https://www.nplindia.org/index.php/amcsnzt_2023/ AN - OPUS4-58572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adamczyk, Burkart A1 - Adam, Christian A1 - Stephan, D. A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit T1 - Production of a hydraulic material from post-treated steelmaking slags N2 - Steelmaking slag is a by-product of steel production of which 4.5 Mt were produced in 2020 in Germany alone. It is mainly used in road construction, earthwork and hydraulic engineering. A smaller part is returned to the metallurgical circle, used as fertilizer or landfilled. With this use, iron oxides still contained in steelmaking slag are lost. In addition, the possibility of producing higher-grade products from steelmaking slag is foregone. In recent decades, many researchers have investigated the production of Portland cement clinker and crude iron from basic oxygen furnace slags (BOFS) via a reductive treatment. Carbothermal treatment of liquid BOFS causes a reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density. Simultaneously, the chemical composition of the reduced slag is adapted to that of the Portland cement clinker. In this study, German BOFS was reduced in a small-scale electric arc furnace using petrol coke as a reducing agent. The resulting low-iron mineral product had a similar chemical composition to Portland cement clinker and was rich in the tricalcium silicate solid solution alite (Ca3SiO5). Based on its chemical and mineralogical composition, similar to that of Portland cement clinker, the reduced BOFS has the potential to react comparably. In our study, the reduced BOFS produced less heat of hydration compared to OPC and its hydraulic reaction was delayed. However, adding gypsum has been shown to accelerate the hydration rate of the reduced BOFS compared to that known from the calcium silicates of Portland cement clinker. Further research to improve the hydraulic properties of the reduced slag is essential. If successful, producing a hydraulic binder and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry. T2 - 16th International Congress on the Chemistry of Cement ICCC 2023 CY - Bangkok, Thailand DA - 18.09.2023 KW - Steelmaking slag KW - Alite hydraulic reactivity KW - Clinker substitute PY - 2023 AN - OPUS4-58522 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerrits, Ruben A1 - Hennehan, M.J. A1 - Frick, D.A. A1 - von Blanckenburg, F. A1 - Schumacher, Julia A1 - Gorbushina, Anna T1 - The role of melanin in fungal mineral weathering and metal corrosion N2 - Melanins are organic pigments produced by most fungi. These organisms either fix these pigments in their cell wall or secrete them into their extracellular environment to protect themselves against an array of physicochemical stresses (e.g., UV irradiation, desiccation, ...). Melanin can adsorb metals like Fe. How this affects fungal uptake of Fe and deterioration of Fe-containing minerals and metals is however less known. To study this, we use the model fungi Knufia petricola A95, a rock-inhabiting fungus known to deteriorate minerals and have melanised cell walls, and Amorphotheca resinae, able to contaminate fuel tanks, secrete melanin and corrode metals. In K. petricola, we have deleted genes involved in melanin production and Fe uptake using CRISPR/Cas. Through comparison of the geochemical signatures of these gene deletion mutants with those of the wild type (WT), we explore the specific mineral/metal deterioration mechanisms of melanised fungi. Fe isotope signatures of the biomass of melanin- and Fe uptake-deficient mutants of K. petricola revealed that Fe adsorbed either directly onto melanin or after being reduced by Fe reductases. Importantly, once adsorbed to melanin, Fe could not be mobilised and taken up into the cell: both the WT and its melanin-deficient mutant, previously grown at Fe replete conditions, showed similar growth at Fe deficient conditions. Olivine dissolution experiments revealed that Fe oxidation inhibits dissolution. K. petricola was able to enhance dissolution when this inhibition is strongest (at pH 6) and prevented dissolution when this inhibition is weakest (at pH 4). The fungus therefore dissolves olivine by interacting with the oxidised Fe at the olivine surface. However, Fe uptake did not seem to be involved: mutants deficient in various Fe uptake mechanism dissolved olivine at the same rate as the WT. This indicates that Fe adsorption onto melanin might play a key role. This is also shown by K. petricola’s ability to enhance olivine dissolution even further if secreting a melanin precursor and A. resinae’s corrosion of carbon steel whilst secreting melanin. Combined, our results imply that the Fe adsorbed to melanin cannot be taken up but enables fungi to deteriorate Fe-containing substrates at a higher rate. T2 - Goldschmidt 2023 Conference CY - Lyon, Frankreich DA - 10.07.2023 KW - MIC KW - Bio-weathering KW - Olivine PY - 2023 AN - OPUS4-58523 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bell, Jérémy A1 - Climent, Estela A1 - Gotor, Raúl A1 - Tobias, Charlie A1 - Martin-Sanchez, Pedro M. A1 - Rurack, Knut T1 - Dipstick coated with polystyrene-silica core-shell particles for the detection of microbiological fuel contamination N2 - Microbial contamination of fuels by fungi or bacteria poses risks such as corrosion and fuel system fouling, which can lead to critical problems in refineries and distribution systems and has a significant economic impact at every stage of the process. Many factors have been cited as being responsible for microbial growth, like the presence of water in the storage tanks. In fact, only 1 % water in a storage system is sufficient for the growth of microorganisms like bacteria or yeasts, as well as for the development of fungal biomass at the oil/water interface. This work presents a rapid test for the accurate determination of genomic DNA from aqueous fuel extracts. The detection is based on the use of polystyrene-mesoporous silica core-shell particles onto which modified fluorescent molecular beacons are covalently grafted. These beacons contain in the hairpin loop a target sequence highly conserved in all bacteria, corresponding to a fragment of the 16S ribosomal RNA subunit. The designed single-stranded molecular beacon contained fluorescein as an internal indicator and a quencher in its proximity when not hybridized. Upon hybridization in presence of the target sequence, the indicator and the quencher are spatially separated, resulting in fluorescence enhancement. To perform the assay the developed particles were deposited on different glass fibre strips to obtain a portable and sensitive rapid test. The assays showed that the presence of genomic DNA extracts from bacteria down to 50–70 μg L–1 induced a fluorescence response. The optical read-out was adapted for on-site monitoring by fitting a 3D-printed case to a conventional smartphone, taking advantages of the sensitivity of the CMOS detector. Such embedded assembly enabled the detection of genomic DNA in aqueous extracts down to the mg L–1 range and represents an interesting step toward on-site monitoring of fuel contamination. T2 - IMA 2023 CY - Chania, Greece DA - 18.09.2023 KW - Teststreifen KW - Test strip KW - Microbial KW - Mikrobiell KW - Smartphone KW - Particles KW - Partikeln PY - 2023 AN - OPUS4-58526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Schwirn, K. A1 - Kuhlbusch, T. A1 - Völker, D. T1 - OECD TG 125 Particle size and size distribution of Nanomaterials N2 - This presentation was held in an OECD Webinar introducing the newly developed and published OECD TG 125 on particle size and size distribution. The presentation is explaining the structure if the TG 125 and addresses all included methods and methodologies in a short and understandable way for the broader public. The presentation includes sections about nano-particles and nano-fibres. T2 - Webinar Series on Testing and Assessment Methodologies CY - Online meeting DA - 07.02.2023 KW - Nano KW - Nanomaterials KW - OECD KW - Test guideline KW - Size PY - 2023 UR - https://www.oecd.org/chemicalsafety/nanomet/presentations-webinar-nanomaterials-particle-size-distribution-test-guideline-125.pdf AN - OPUS4-58447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - OECD Prüfrichtlinie 125 N2 - Diese Präsentation ist eine Einführung in die OECD TG 125 zur Bestimmung der Partikelgrößen von Nanomaterialien. Es wird auf die verchiedenen Probleme der Partikelgrößenbestimmung eingegangen wie z.B. verschiedene Oberflächenschichten, Äquivalenzdurchmesser und Verteilungsfunktionen. Gleichzeitig werden die neuen Begrifflichkeiten eingeführt, die in der TG 125 definiert neu werden. T2 - BAM Akademie Digitaler Info-Tag "Nano or not Nano" CY - Online meeting DA - 16.02.2023 KW - Nano KW - Partikel KW - Größe KW - Partikeldurchmesser KW - Äquivalenzdurchmesser PY - 2023 AN - OPUS4-58449 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - Differentielles Mobilitäts Analyse System (DMAS) N2 - Die Bestimmung der Nanopartikelgrößen- und -formverteilung nach OECD TG 125 mit einem Differentiellen Mobilitäts Analyse System (DMAS), auch bekannt als SMPS, wird vorgestellt: - Generelles Messprinzip - Welchen Durchmesser misst die Methode? - Welche Partikel kann diese Methode messen? - Welche Informationen kann diese Methode liefern? - Wo stößt die Methode an ihre Grenzen? - Implementierung und Datenauswertung, - Reporting. Anschließend wurde eine Q&A-Session für DMAS/SMPS organisiert. T2 - BAM Akademie Digitaler Info-Tag "Nano or not Nano" CY - Online meeting DA - 16.02.2023 KW - Partikel KW - Nanopartikel KW - SMPS KW - Größenbestimmung KW - DMAS PY - 2023 AN - OPUS4-58450 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna A1 - Schumacher, Julia A1 - Abdallah, Khaled T1 - Black fungi on technosphere surfaces: new niches for roof-inhabiting cousins N2 - Human-made systems, also called “build environment” or “technosphere”, sustain human comfort as well as our industrial activities. These systems have become particularly widespread since the Industrial Revolution, i.e., since the 17th century. At the same time, these technical systems – buildings, monuments, energy production, transformation and transmission, water purification and supply systems - serve as new habitats for living organisms. Life is ubiquitously present on our planet since a very long time: the Earth is 4.54 billion years old and microbial communities have played a key role on our planet for 3.7 billion years. Once human-made system appeared, microorganisms became an integral part of all types of technosphere infrastructure as well. Here we will illustrate biosphere-technosphere interactions using a specific example of the black fungi and their impact on the efficiency of solar (photovoltaic) panels. This expanding renewable infrastructure for electricity generation is growing on all continents - and create a specific, arid habitat for stress-tolerant black fungi. Black fungi were once discovered in hot and cold natural deserts – and now belong to the persistent colonisers of human-made deserts of solar parks. This new niche is evolving an impressive biodiversity. So far more than 60 isolates of black fungi belonging to Arthoniomycetes, Eurotiomycetes and Dothideomycetes were obtained from solar panels in Europe and Americas. Here we will present the analysis of this emerging anthropogenic biodiversity. Opportunities for future research in the field include quantification of the microbial load on technosphere surfaces – along with characterisation of the corresponding microbial diversity. The strategy of precise measurement and characterisation will enable us to reliably determine the beneficial and harmful functions that living microorganisms play in the functioning of energy-generating systems – and technosphere in general. T2 - IUBMB Focused Meeting on Extremophilic Fungi (FUN-EX) CY - Ljubljana, Slovenia DA - 19.09.2923 KW - Biosphere-technosphere interaction KW - Microbial communities KW - Solar parks PY - 2023 AN - OPUS4-58451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Catanzaro, Ilaria A1 - Nitsche, Sarah A1 - Gorbushina, Anna A1 - Schumacher, Julia A1 - Onofri, S. T1 - Generation of Cryomyces antarcticus mutants to explore the importance of DHN melanin for survival N2 - Cryomyces antarcticus, a cryptoendolithic melanized fungus endemic to Antarctica (phylum Ascomycota, class Dothideomycetes incertae sedis), has demonstrated high capability to survive extreme environmental conditions like those found in space (e.g., ionizing radiation, vacuum, microgravity), thus fueling fundamental astrobiological questions like “the search for life beyond Earth”. Its extraordinary resilience has been attributed to the presence of thick, highly melanized cell walls, which may contain both DHN and DOPA melanins. To better understand the contribution of DHN melanin to the overall resilience of C. antarcticus, we decided to generate melanin-deficient mutants by genetic engineering. For this, the melanin-PKS (polyketide synthase)- encoding ortholog was identified in the C. antarcticus CBS 116301 genome and used to design primers for re-sequencing of the capks1 locus in the strain CCFEE 515. Based on the genetic toolkit developed for the black fungus Knufia petricola, we designed a strategy for mutating capks1. Protoplasts of C. antarcticus CCFEE 515 were generated and co-transformed with a circular AMA-containing plasmid for expression and in-vivo assembly of Cas9 and two capks1-specific sgRNAs and a PCR-generated donor DNA i.e., a hygromycin resistance cassette flanked by ~75-bp-long sequences homologous to the capks1 locus. Transformation of C. antarcticus is challenging because of its very slow growth and uncertain gene copy number. It took six months from obtaining enough biomass for cell wall lysis to transferring the putatively resistant transformants for genotyping, but we eventually managed to generate three independent non-melanized (whitish) Δcapks1 mutants! We are now awaiting first complemented strains as ultimate genetic transformation control. They are considered to have a wild-type-like pigmentation due to the reintroduction of the wild-type capks1 into the Δcapks1 mutant. T2 - IUBMB Focused Meeting on Extremophilic Fungi (FUN-EX) CY - Ljubljana, Slovenia DA - 19.09.2023 KW - Black fungus KW - Genetics KW - UV tolerance KW - Melanin PY - 2023 AN - OPUS4-58458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oberbeckmann, Sonja A1 - Scales, Brittan A1 - Hassenrück, Christiane A1 - Moldaenke, Lynn A1 - Rummel, Christoph A1 - Völkner, Corinna A1 - Hassa, Julia A1 - Rückert, Christian A1 - Rynek, Robby A1 - Busche, Tobias A1 - Kalinowski, Jörn A1 - Jahnke, Annika A1 - Schmitt-Jansen, Mechthild A1 - Wendt-Potthoff, Katrin T1 - Hunting for pigments in plastic biofilms from the Great Pacific Garbage Patch N2 - Each year, an immense amount of plastic debris enters marine ecosystems, much of which ends up in the Great Pacific Garbage Patch (GPGP). The plastic fragments are home to a diverse community of microorganisms, and while researchers have gained a better understanding of these marine plastic biofilms, we lack insights into the physiology and genomic potential of the bacteria that colonize them. Examining the lifestyle of plastic colonizers from the GPGP is particularly intriguing, as the high concentration of plastics in this accumulation zone might allow for a microbial adaptation to this unique man-made habitat. A range of pigmentation was observed in 67 isolated strains obtained directly from plastic pieces sampled from the GPGP surface water. Sequence comparison between the cultivated bacterial strains and the 16S rRNA gene amplicon dataset confirmed that most of the cultivates could also be captured through DNA-only methods. Whole genome analysis of four taxonomically diverse representatives revealed multiple carotenoid pathways, including those to produce less common glycosylated carotenoids, like sarcinaxanthin glucoside. Further, we identified a potentially new Rhodobacteraceae species containing a photosynthetic gene cluster (PGC). Absorption analysis confirmed the actual production of the carotenoids and bacteriochlorophyll a. Floating plastics represent a habitat with strong UV-light exposure, making the protection with antioxidant carotenoids as well as the ability to use light as an energy source highly beneficial traits for plastic colonizers. Our findings indicate, that the production of pigments is a common adaption mechanism for plastic-associated bacteria, and that plastic biofilms present a so far overlooked source of rare carotenoids and light-harvesting mechanisms. T2 - Annual Conference of The Association for General and Applied Microbiology (VAAM) CY - Göttingen, Germany DA - 10.09.2023 KW - Plastic biofilm KW - Phototrophic bacteria KW - Plastic pollution PY - 2023 AN - OPUS4-58443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Erdmann, Eileen A. A1 - Nitsche, Sarah A1 - Gerrits, Ruben A1 - Heeger, Felix A1 - Gorbushina, Anna T1 - Genetic engineering of black fungi: lessons learned from Knufia petricola N2 - The exponential rise in the number of fungal genomes sequenced by next-generation sequencing techniques makes it necessary to increase efforts to correctly annotate and assign gene functions. There are two possibilities to explore a genome and its gene functions. The hypothesis-based method proves the function of already existing gene/allele candidates by targeted mutagenesis - so called reverse genetics. The basis of forward genetics approaches is the random mutagenesis of the genome, followed by screening of obtained mutants for the phenotype of interest, and identification of the mutated genes in the respective mutants. This strategy is hypothesis-generating, means it is necessary to verify the relationship between the detected mutations and the observed phenotype by targeted mutagenesis of the identified gene. We developed a toolbox for editing the genome of the rock inhabitant Knufia petricola [Eurotiomycetes, Chaetothyriales] that allows the study of the phenotypic characteristics of black fungi such as the regulation of pigment synthesis, general stress responses, oligotrophy, and the unusual modes of cell division by advanced reverse and forward genetics approaches. The toolbox includes the annotated genome sequence of strain A95, efficient strategies for CRISPR/Cas9-based genome editing and live-cell imaging using genetically encoded fluorescent proteins, as well as protocols for -omics approaches and for simulation of mineral weathering. A forward genetics approach using transposon mutagenesis is currently developed for identifying essential genes. The established protocols and knowledge gained from K. petricola form a starting point for making other fungi from extreme environments accessible to genetic manipulation. T2 - IUBMB Focused Meeting on Extremophilic Fungi (FUN-EX) CY - Ljubljana, Slovenia DA - 19.09.2023 KW - Fungus KW - Extremotolerance KW - Genetics KW - Model organism PY - 2023 AN - OPUS4-58424 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Brandhorst, Antonia A1 - Catanzaro, Ilaria A1 - Nitsche, Sarah A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Gorbushina, Anna T1 - Versatile DHN melanin – spotlight on its function in microcolonial black fungi N2 - Dihydroxynaphthalene (DHN) melanin is produced by diverse Ascomycetes via slightly differing biosynthetic routes. The polyketide synthases (PKS) release the heptaketide YWA1, the hexaketide AT4HN or the pentaketide T4HN. The first two products are deacetylated by ‘yellowish-green’ hydrolases to T4HN, and T4HN is further converted by a core set of enzymes to DHN. Final polymerization steps are accomplished by multicopper oxidases. DHN melanogenesis is often regulated in a spatial and temporal fashion resulting e.g., in melanized reproduction and survival structures of the foliar plant pathogen Botrytis cinerea (Schumacher 2016, Mol Microbiol). In contrast, a polyphyletic group of Ascomycetes (microcolonial fungi/ black yeasts) dwelling in hostile habitats such as bare rock surfaces in hot and cold deserts, exhibits constitutive melanogenesis. Here, DHN melanin builds a protective layer around all vegetative cells thus contributing to the survival of diverse environmental stresses even without specialized reproduction structures. For studying the relevance of constitutive DHN melanogenesis for tolerance of abiotic and biotic stresses, adhesion to substrates and subsequent damage of colonized surfaces, the rock-inhabiting fungus Knufia petricola was chosen as gene functions in this fungus can be studied by CRISPR/Cas9-based genome editing. The putative melanogenic genes were identified in the genome of K. petricola, deleted to confirm their involvement in DHN melanogenesis and co-expressed in Saccharomyces cerevisiae for reconstruction of the synthesis pathway. Phenotypes of DHN-deficient mutants are studied. Here, we will discuss the role of the DHN melanin layer on the outer cell wall in tolerating UV irradiation. T2 - Annual conference 2023 of the Association for General and Applied Microbiology CY - Göttingen, Germany DA - 10.09.2023 KW - Pigment KW - UV radiation KW - Tolerance PY - 2023 AN - OPUS4-58425 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Eileen A1 - Kunze, R. A1 - Gorbushina, Anna A1 - Schumacher, Julia T1 - In-vivo mutagenesis of the rock inhabitant Knufia petricola by a customized Ac/Ds transposon system N2 - Microcolonial black fungi ubiquitously inhabit sun-exposed natural and man-made surfaces of our planet. To promote genetic studies, CRISPR/Cas9-based genome editing was implemented in the rock-inhabiting fungus Knufia petricola (Eurotiomycetes/ Chaetothyriales). Now efficient targeted mutagenesis of K. petricola - as a representative of the polyphyletic group of black fungi - enables the elucidation of extremotolerance, oligotrophism, unusual types of cell division, mineral weathering and symbiotic interactions. Even more progress on assigning functions to yet unknown genes can be achieved by a forward genetics approach. We chose the two-component Activator/Dissociation (Ac/Ds) transposon system from maize for generating K. petricola insertional mutants by in-vivo mutagenesis. For the optimal use of this genetic tool, an inducible promoter i.e, from the metabolism-independent Tet-on system, was combined with the AcTPase-coding sequence enabling the regulatable transposition of the resistance cassette-containing Ds transposon. In total, six auxotrophic Ac/Ds starter strains containing the Ds transposon at different position of ade2, ura3 or ppt1 were generated. The cultivation of these strains with doxycycline for induction of TET::Ac and subsequent selection of cells on ADE/URA/LYS-lacking media resulted in prototrophic colonies (revertants) for most Ac/Ds strains. Amplicon sequencing of excision sites revealed characteristic footprint patterns, proving that the transposon jumped. For identifying unknown Ds re-insertions sites, the thermal asymmetric interlaced (TAIL)-PCR was successfully implemented. First identified Ds re-insertion sites suggest that the distribution pattern may depend on the excision site. Currently, transposition frequencies and genome-wide distribution of re-insertion sites are studied in different Ac/Ds starter strains to identify the best candidate for generating saturated mutant libraries. This transposon mutagenesis strategy is also interesting for studying other black fungi, because once the Ac and Ds components are integrated in the genome, the fungus ‘only’ needs to be cultivated for generating insertional mutants. T2 - IUBMB Focused Meeting on Extremophilic Fungi (FUN-EX) CY - Ljubljana, Slovenia DA - 19.09.2023 KW - Black fungi KW - Genetics KW - Transposon KW - Mutagenesis PY - 2023 AN - OPUS4-58427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aumont, Cedric A1 - McMahon, Dino Peter T1 - Genomic innovations underlying the evolution of termite social behaviour N2 - The phylogeny of the Blattodea boasts a wide degree of sociality spanning from solitary cockroaches to advanced ecosystem-dominating higher termite societies. The emergence of sociality in the termites was associated with the acquisition of a diverse range of social structures and differential expression of specific gene network. Previous work has found evidence for a caste-specific social defence system in termites leading to an immune system that may favour group over individual defence. While preliminary work suggests a correlation between social transitions and a reduction of immune gene family diversity, the lack of available high-quality termite genomes hampers complete knowledge of the true diversity of immune gene evolution across termite phylogeny. Here, we report on the sequencing and assembly of 50 high-quality long-read-based genomes and 180 caste- and sex-specific brain transcriptomes across major termite and cockroach sister-branch lineage. We investigate the diversity and evolutionary history of immune genes across genomes, and the potential gene networks that have evolved with the emergence of termite sociality and some aspect of immune related behaviours. T2 - Invited talk at University Paris 13 CY - Villetaneuse, France DA - 27.02.2023 KW - Immune gene family KW - Gene network KW - Eusociality KW - Termite phylogeny KW - Group defence PY - 2023 AN - OPUS4-58300 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piehl, Patrick T1 - Thermochemische Aufarbeitung von Stahlwerksstäuben und -schlämmen zur Zink- und Eisenrückgewinnung N2 - Stahlwerksstäube und -schlämme enthalten in der Regel Schwermetalle wie Zink, Blei und Cadmium, die ein direktes Recycling verhindern und diese Stoffe potenziell umweltgefährdend machen. Um diese Schwermetalle aus den Materialien zu entfernen, werden drei thermochemische Verfahren zur Aufarbeitung von Gichtgasschlamm, Elektroofenstaub und ähnlichen Stahlwerksstäuben vorgestellt. Zum einen kann die Mischung von Elektroofenstaub mit chloridhaltigen Lösungen, wie sie z. B. in der Titandioxidproduktion anfallen, gemischt werden, um bei der thermischen Behandlung Schwermetallchloride zu effektiv verdampfen. Weiterhin kann der im Gichtgasschlamm enthaltene Kohlenstoff genutzt werden, um in Mischungen aus Gichtgasschlamm und Elektroofenstaub bei der thermischen Behandlung als Reduktionsmittel zu wirken. Dieses Verfahren führt zur Rückgewinnung von Zink und metallischem Eisen und wird im Technikums- und Pilotmaßstab erprobt. Abschließend wird die Nutzung von Wasserstoff als Reduktionsmittel für Elektroofenstaub vorgestellt. Hierbei lässt sich der Reststoff potenziell klimaneutral in Eisenschwamm umwandeln, wobei die chemischen Grundlagen anhand von DTA-Experimenten und thermodynamischen Simulationen ergründet werden. T2 - Berliner Konferenz Metallkreisläufe CY - Berlin, Germany DA - 13.04.2024 KW - Elektroofenstaub KW - Gichtgasschlamm KW - Recycling KW - Ressourcenrückgewinnung KW - Zink PY - 2024 AN - OPUS4-59726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Gorbushina, Anna A. T1 - How does light affect rock-inhabiting fungi? N2 - Sunlight is an almost unavoidable environmental cue and plays a fundamental role in the biology of pro- and eukaryotic organisms. To cope with sunlight-associated stresses e.g., high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses, it is important for organisms to accurately sense and respond to changes in light. The benefits of light are obvious for green organisms such as cyanobacteria, algae and plants which use light as an energy source (photosynthesis). Less apparent are other light-dependent processes such as light-driven DNA repair by photolyases (photoreactivation) or ion pumping by microbial opsins. Fungi that can share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess many proteins for absorbing UV/blue, green, red and far-red light, produce the black 1,8 dihydroxynaphthalene (DHN) melanin and orange-red carotenoids, and may live in multispecies biofilms. Here, we are addressing the question to which extent constitutive pigment formation (melanin and carotenoids) and responses mediated by the stress-activated mitogen-activated protein (MAP) kinase contribute to the observed light (UV-B) tolerance of K. petricola. T2 - 32nd Fungal Genetics Conference CY - Pacific Grove, CA, USA DA - 12.03.2024 KW - Knufia petricola KW - Black fungi KW - Light-induced stress PY - 2024 AN - OPUS4-59732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Jovičević-Klug, M. A1 - Raabe, D. T1 - Gewinnung von grünem Eisen und weiteren Wertstoffen aus Rotschlamm mittels Wasserstoffplasma N2 - Rotschlamm fällt in sehr großen Mengen bei der Herstellung von Aluminiumoxid an und wird fast ausschließlich deponiert. Es wird eine neue Technologie vorgestellt bei der das im Rotschlamm enthaltene Eisenoxid mittels Wasserstoffplasma reduziert wird. Es wird ein Reaktionsmechanismus über Titanomagnetit und Hercynit vorgeschlagen. T2 - Berliner Konferenz Metallkreisläufe CY - Berlin, Germany DA - 13.03.2024 KW - Rotschlamm KW - Wasserstoffplasma PY - 2024 AN - OPUS4-59722 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Adam, Christian T1 - Klärschlammasche Monitoring 2022/23 - P-Löslichkeiten und Schwermetallgehalte N2 - Im Rahmen des BMBF Projektes R-Rhenania wurden von fast allen Monoverbrennungsanlagen in Deutschland Klärschlammasche-Proben eingesammelt. Diese Aschen wurden auf die Gesamtchemie-Zusammensetzung, Schwermetalle und die Löslichkeit des Phosphates untersucht. T2 - 6. Berliner Klärschlammkonferenz BKK CY - Berlin, Germany DA - 13.11.2023 KW - Monoverbrennungsanlage KW - Phosphor KW - Neutralammoniumnitrat KW - Zitronensäure PY - 2023 AN - OPUS4-59436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Adam, Christian T1 - Klärschlammasche Monitoring 2022/23 - Erste Ergebnisse: P Löslichkeiten & Schwermetalle N2 - Im Rahmen des BMBF Projektes R-Rhenania wurden von fast allen Monoverbrennungsanlagen in Deutschland Klärschlammasche-Probeneingesammelt. Diese Aschen wurden auf die Gesamtchemie-Zusammensetzung, Schwermetalle und die Löslichkeit des Phosphates untersucht. T2 - 95. Sitzung des DWA Fachausschusses KEK 3 CY - Hannover, Germany DA - 27.11.2023 KW - Phosphor KW - Monoverbrennungsanlage KW - Neutralammoniumcitrat KW - Zitronensäure PY - 2023 AN - OPUS4-59437 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina T1 - Beyond the text: What writing materials of the Cairo Genizah tell us N2 - Results: - Four types of inks were measured iron gall (vitriolic and non vitriolic), carbonic, mixed and vegetable inks. - We need to start analyzing systematically the organic part of the inks. - Great variety in the composition of the inks. - No correlation between the type of ink used and any other criteria apart from a personal preference. - Inks purchased by (some) scribes. - Reconstruction of the chronology of writing and signing of certain legal documents. - Comparison with documents written by the Muslim court. T2 - Ink Workshop CY - Munich, Germany DA - 28.06.2022 KW - Ink analyses KW - Manuscript studies KW - X-Ray fluorescence analyses KW - Cairo Genizah KW - Middle Ages PY - 2022 AN - OPUS4-58874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina T1 - Étude archéométrique des manuscrits de la Genizah du Caire: Ce que l'encre nous révèle des communautés juives T1 - Archaeometric study of the Genizah manuscripts of Cairo: What ink reveals to us about Jewish communities N2 - Conclusion et piste: Il semblerait qu’il n’existe pas de corrélation entre le type d’encre utilisés et d’autres critères recherchés à part une marque de préférence personnelle, sauf en ce qui concerne des documents religieux, auquel cas une différence se fait en function de la communauté. Les résultats réunis dans cette étude semble indiquer que les scribes achètent leur propre encre. L’analyse des encres peut nous aider à retracer une chronologie de l’écriture et signature de certains documents juridiques. Élargissement du corpus: - Comparaison avec des documents écrits par la cour du Qadi - Documents d’autres collections - Avec d’autres documents contemporains (Génizah Afghane) N2 - Conclusion and track: It seems that there is no correlation between the type of ink used and other criteria sought apart from a mark of personal preference, except with regard to religious documents, in which case a difference is made according to the community. The results gathered in this study seem to indicate that scribes purchased their own ink. Ink analysis can help us trace a chronology of the writing and signing of certain legal documents. Corpus expansion: - Comparison with documents written by the court of the Qadi - Documents from other collections - With other contemporary documents (Génizah Afghane) T2 - Codicologie quantitative et sociologie du livre médiéval : Faire corps par le livre CY - Paris, France DA - 31.01.2023 KW - Encre KW - Genizah du Caire KW - Archéométrie KW - Manuscrits KW - Moyen-âge PY - 2023 AN - OPUS4-58875 LA - fra AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Looking through the eyes of fungi: from photoperception to photoresponses and beyond N2 - Sunlight is an almost unavoidable environmental cue and plays a fundamental role in the biology of pro- and eukaryotic organisms. To cope with sunlight-associated stresses e.g., high temperatures, UV radiation, accumulation of reactive oxygen species, desiccation, and osmotic stress, it is important for organisms to accurately sense and respond to changes in light. The benefits of light are obvious for green organisms such as cyanobacteria, algae and plants which use light as an energy source (photosynthesis). Fungi that can share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. Examples are the plant pathogen Botrytis cinerea, the gray mold fungus, and the rock inhabitant Knufia petricola, a microcolonial black fungus which forms multispecies biofilms with bacteria and algae. T2 - 20th Symposium of the Research Training Group on Bioactive Peptides – The colorful tree of life CY - Berlin, Germany DA - 23.01.2024 KW - Black fungi KW - Melanin KW - Stress tolerance PY - 2024 AN - OPUS4-59543 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes A1 - Adam, Christian A1 - Emter, J. A1 - Leimkötter, D. T1 - Thermochemisches P Recycling aus Klärschlamm – erste großtechnische Anlage am Standort Altenstadt (Bayern) N2 - Im Verbundprojekt R-Rhenania wird eine industrielle Demonstrationsanlage am Standort der Monoverbrennungsanlage Altenstadt der Firma Emter errichtet und im Jahr 2024 den Betrieb aufnehmen. Die vorhandene Rostfeuerung-Monoverbrennung wird so umgebaut, dass ein neues thermochemisches Verfahren integriert werden kann, welches hochwirksame und schadstoffarme Dünger produziert (bis zu 17.000 t/a). Die thermochemischen Produkte werden in Gefäß- und Feldversuchen im ökologischen Landbau auf ihre Düngewirkung getestet. Die Umweltverträglichkeit der Demonstrationsanlage wird untersucht, wie auch die Übertragbarkeit des Verfahrens auf weitere Regionen. T2 - 13. VDI Klärschlammbehandlung CY - Koblenz, Germany DA - 14.09.2022 KW - Phosphor KW - Versuchskampagne KW - Recycling KW - Nährstoffe KW - Dünger PY - 2022 AN - OPUS4-59576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adam, Christian A1 - Herzel, Hannes T1 - R-Rhenania - Modifiziertes Rhenania Phosphat aus Klärschlammasche für Bayern N2 - Im Verbundprojekt R-Rhenania wird eine industrielle Demonstrationsanlage am Standort der Monoverbrennungsanlage Altenstadt der Firma Emter errichtet und im Jahr 2024 den Betrieb aufnehmen. Die vorhandene Rostfeuerung-Monoverbrennung wird so umgebaut, dass ein neues thermochemisches Verfahren integriert werden kann, welches hochwirksame und schadstoffarme Dünger produziert (bis zu 17.000 t/a). Die thermochemischen Produkte werden in Gefäß- und Feldversuchen im ökologischen Landbau auf ihre Düngewirkung getestet. Die Umweltverträglichkeit der Demonstrationsanlage wird untersucht, wie auch die Übertragbarkeit des Verfahrens auf weitere Regionen. T2 - Statusseminar RePhoR CY - Frankfurt am Main, Germany DA - 03.05.2023 KW - Phosphor KW - Monoverbrennung KW - Recycling KW - Nährstoffe KW - Dünger PY - 2023 AN - OPUS4-59486 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Schwibbert, Karin A1 - Richter, Anja M. A1 - Krüger, Jörg T1 - Laserstrukturierte Oberflächen Ein Weg zur Kontrolle der Biofilmbildung? N2 - Bakterielle Biofilme stellen in medizinischen und industriellen Bereichen ein ernsthaftes Problem dar. Eine der größten gesellschaftlichen Herausforderungen liegt in der zunehmenden Resistenz von Bakterien gegen Biozide, die bei antimikrobiellen Behandlungen eingesetzt werden, z.B. durch übermäßigen Einsatz in Medizin, Industrie und Landwirtschaft oder durch Reinigung und Desinfektion in Privathaushalten. Daher sind neue effiziente bakterienabweisende Strategien, die den Einsatz von Bioziden vermeiden, dringend erforderlich. Ein vielversprechender Weg zur Erzielung bakterienabweisender Oberflächen liegt in der berührungslosen und aseptischen großflächigen Laserbearbeitung von technischen Oberflächen. Maßgeschneiderte Oberflächentexturen, ermöglicht durch verschiedene Laserbearbeitungsstrategien, die zu topographischen Skalen im Bereich von Nanometern bis Mikrometern führen, können eine Lösung für diese Herausforderung darstellen. In dem Vortrag wird ein Überblick über den aktuellen Stand der Technik bei der subtraktiven Texturierung von Laseroberflächen zur Kontrolle der Biofilmbildung bei verschiedenen Bakterienstämmen und in unterschiedlichen Umgebungen gegeben. Auf der Grundlage spezifischer Eigenschaften von Bakterien und laserbearbeiteten Oberflächen werden die Herausforderungen antimikrobieller Oberflächendesigns erörtert und zukünftige Richtungen aufgezeigt. T2 - GRAVOSeminar, GRAVOmer Kompetenznetzwerk CY - Online meeting DA - 28.02.2024 KW - Laser-Materialbearbeitung KW - Ultrakurzpuls-Laser KW - Biofilme KW - Antibakterielle Oberflächen KW - Oberflächenfunktionalisierung PY - 2024 UR - https://gravomer.de/veranstaltungen-anzeigen/laserstrukturierte-oberflaechen-ein-weg-zur-kontrolle-der-biofilmbildung AN - OPUS4-59594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Roesch, Philipp A1 - Vogel, Christian T1 - micro-XRF und XANES-Analytik von PFAS N2 - Ergebnispräsentation über gesammelte Ergebnisse der Synchrotron F µ-XRF und -XANES Spektroskopischen Untersuchungen von PFAS und PFAS-haltigen Materialien T2 - Online-Seminar des Fortbildungsverbundes Boden und Altlasten Baden-Württemberg CY - Online meeting DA - 07.12.23 KW - PFAS KW - XANES KW - XRF KW - Röntgenspektroskopie KW - Synchrotron PY - 2023 AN - OPUS4-59077 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Risk Assessment of Biocide Resistance N2 - This presentation details approaches for the risk assessment of biocide resistance. Different methods are presented to acquire the necessary data for such risk assessments. T2 - OECD, 7th Meeting of the Working Party on Biocides CY - Leiden, Netherlands DA - 18.09.2023 KW - Antimicrobial resistance KW - Bacteria KW - Standardization KW - Biocides PY - 2023 AN - OPUS4-59062 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz A1 - Karafiludis, Stephanos A1 - Pimentel, C. A1 - Montes Hernandez, G A1 - Kochovski, Z A1 - Bienert, Ralf A1 - Weimann, Karin A1 - Emmerling, Franziska A1 - Scoppola, E A1 - Van Driessche, A T1 - Solution-driven processing of calcium sulfate: the mechanism of the reversible transformation of gypsum to bassanite in brines N2 - Calcium sulfate hemihydrate (CaSO4ᐧ0.5H2O), also known as bassanite, has been used as a precursor to produce gypsum (dihydrate, CaSO4ᐧ2H2O) for various construction and decorative purposes since prehistoric times. The main route to obtain hemihydrate is a thermal treatment of gypsum at temperatures typically between 150 °C and 200 °C to remove some of the structural water. In this contribution, we introduce (Fig. 1) a more efficient and sustainable method (T < 100 °C) that enables the direct, rapid, and reversibly conversion of gypsum to bassanite using reusable high salinity aqueous solutions (brines with c[NaCl] > 4 M). The optimum conditions for the efficientproduction of bassanite in a short time (< 5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the typical behaviour of the bassanite phase in low salt environments. Traditionally, hemihydrate is obtained through a solid state thermal treatment because bassanite is considered to be metastable with respect to gypsum and anhydrite in aqueous solutions, and therefore gypsum-to-bassanite conversion should not occur in water. Its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures is inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline structure for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios. T2 - Granada Münster Discussion Meeting GMDM 10 CY - Münster, Germany DA - 29.11.2023 KW - Gypsum KW - Bassanite KW - Calcium sulfate KW - Recycling KW - Scattering PY - 2024 AN - OPUS4-59162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Evolutionsbiologischer Ursprung von Holz-, Material- und Vorratsschädlingen sowie ihre vermeintlichen Anpassungen an den synanthropen Lebensraum N2 - Zahlreiche Insektenarten unter den Käfern und Schmetterlingen besitzen die ökologische Potenz, trockene Materialien pflanzlichen und tierischen Ursprungs als Nahrungs- und Brutsubstrat zu nutzen. Daher findet man diese Tiere auch an und in vom Menschen angelegten Nahrungsvorräten wie z. B. Getreidespeicher, an Kleidungs- und an Gebrauchsgegenständen aus Wolle, Pelzen oder Fellen sowie an oder in natürlichen Baumaterialien wie Holz. Aus wirtschaftlicher Sicht werden sie dann als Vorrats- bzw. Materialschädlinge bezeichnet. Vorrats- und Materialschädlinge haben sehr ähnliche Lebensstrategien. Sie verfügen über eine breite Toleranz gegenüber abiotischen Umweltparametern und sind in der Regel Nahrungsopportunisten. Sie können längere Zeit ohne Nahrungsaufnahme überdauern und haben unter optimalen Bedingungen hohe Reproduktionsraten. Es stellt sich die Frage, ob die auffälligen Anpassungen von Vorrats- und Materialschädlingen an einen menschennahen Lebensraum das Resultat von Prädispositionen und Selektion hin zu einem Lebensformtyp „Lager- oder Materialschädling“ sind, oder ob die synanthropen künstlichen (Öko)Systeme nur als überdimensionierte natürliche Reservoire fungieren. Ökologische und ethologische Prädispositionen und Adaptationen sowie Verbreitungs- und Fortpflanzungsstrategien von Schadinsekten werden hier diskutiert, um phylogenetische und evolutionsbiologische Szenarien beim Übergang von ursprünglichen, also natürlichen Lebensräumen auf relativ jungzeitliche, von Menschen geprägte Habitate, zu rekonstruieren. Die angeführten Beispiele werden im kritischen Bezug zu publizierten Informationen über autökologische, faunistische sowie archäologische und historische Indizien über Ursprung und Ausbreitung von ausgewählten Schadinsekten (Hausbockkäfer, Textilmotten, Kornkäfer) begründet. T2 - Holzschutztagung der Deutschen Bauchemie CY - Erfurt, Germany DA - 30.11.2023 KW - Evolution KW - Umwelt KW - Selektion KW - Anpassung KW - Schädling PY - 2023 AN - OPUS4-58989 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaut, Valerie A1 - Schreiber, Frank A1 - Vareschi, Silvia T1 - Antibiotic tolerance of biofilms emerging fro multicellular effects of antibiotic efflux N2 - The overarching goal of this project is to develop a predictive model for efflux-mediated antimicrobial tolerance in bacterial multicellular assemblies. Our central hypostasis is that efflux pump activity causes emergent antibiotic tolerance of multicellular bacterial populations, through the interplay of efflux mediated spatial interactions and efflux-linked persistence. To test this hypothesis, we will use a combination of microscopy, microbial killing assays, computational modelling, and data analysis, integrating information from 3 types of multicellular assembly: colonies, cell-to-cell interactions in a monolayer microfluidic device, and 3D flow chamber biofilms. Building on our preliminary observations, we will experimentally characterize the link between colony structure and spatial patterns of efflux gene expression in strains that differ in their levels of efflux. We will develop a mathematical model to test whether local growth inhibition of neighbors due to effluxing cells, coupled with local environment-dependent regulation of efflux, can account qualitatively for these results. By including persister cell formation in our model we will predict, and measure, the emergent function of antimicrobial tolerance in our colonies. To fully understand how tolerance emerges from the interplay between efflux-mediated spatial interactions and efflux-linked persister cell formation, we need quantitative measurements at the single cell level. To this end, we will use a microfluidic setup with cells growing in a monolayer to qualify in detail the dependence of efflux expression and persister cell formation on nutrient conditions, the correlation between efflux and persister formation, and the spatial range of efflux-mediated neighbour growth inhibition. To predict and quantitatively understand the emergent multicellular function of tolerance, we will perform individual-based modelling of biofilm growth, using as input the parameters measured on the single-cell level with our microfluidics experiments. Our simulations will predict biofilm spatial structure development, patterns of efflux and persister formation and, ultimately, tolerance to antimicrobial challenge. These predictions will be directly tested in flow-cell biofilm experiments. We are currently generating acrAB-tolC knockout-strain, without efflux activity, and a strain with an inducible acrAB-tolC efflux pump. To distinguish the different strains under the microscope, they were labeled with genes encoding for different fluorescent proteins. All strains are currently characterized in terms of growth, minimum inhibitory concentration of different antimicrobial substances, colony morphology, and biofilm formation ability. On the theoretical side, we are currently working on modeling the system at various scales and degree of detail, ranging from coarse-grained continuum models to stochastic, individual-based models. Some exploratory work was doe to test existing software for individual-based modelling that may be adapted for our purpose. Furthermore, we are in the process of developing more coarse-grained models. This work involves some physiological modelling and literature search, focusing on working mechanisms of efflux pumps and kinetic models for import and export of antibiotics. T2 - SPP Meeting CY - Jena, Germany DA - 04.10.2023 KW - Antibiotic KW - Bioilm KW - Tolerance KW - Efflux PY - 2023 AN - OPUS4-59245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina A1 - Nehring, Grzegorz A1 - Gordon, Nehemia A1 - Rabin, Ira T1 - Material Studies of Torah Scrolls at the Bundesanstalt für Materialforschung und -Prüfung N2 - In recent years the BAM has been focusing on the characterization of the writing materials of the medieval Torah scrolls. The challenge imposed by the study of this specific type of manuscript led to designing and building dedicated stages to ensure the safety of the scrolls during the analysis. Furthermore, the identification of multiple corrections executed in apparently identical inks required broadening the standard two-step protocol of near infrared reflectography and X-ray fluorescence to include multispectral imaging. This work has prepared the division to participate in the large collaborative project “To roll: Materialisierte Heiligkeit (Materialised Holiness)” based at the Free University, Berlin. The presentation will demonstrate the aims of the studies, preliminary results and the strategies adopted by the division 4.5 of the BAM. T2 - EAJS Congress Branching Out: Diversity of Jewish Studies CY - Frankfurt/Main, Germany DA - 16.07.2023 KW - Ink analyses KW - Manuscript studies KW - Torah Scrolls KW - X-Ray fluorescence KW - Middle Ages PY - 2023 AN - OPUS4-58881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehring, Grzegorz A1 - Hahn, Oliver A1 - Shevchuk, Ivan A1 - Huskin, Kyle A1 - Cohen, Zina A1 - Rabin, Ira T1 - Breaking the limits of the non-destructive instrumental analysis of writing inks N2 - The ink analysis protocol developed through cooperation between the Bundesanstalt für Materialforschung und -prüfung in Berlin and the Centre for the Study of Manuscript Cultures at the University of Hamburg involves the use of imaging techniques for ink screening, followed by spectroscopic analysis. In our presentation, we will begin by briefly reviewing the history of writing inks and discussing the three main categories: carbon-based inks, plant, and iron-gall inks. We will address their chronology, precursors, and mixed forms, as well as the features that allow for their identification. Then, we will present the techniques we use in ink analysis, whereby we would like to highlight the limitations, advantages, and disadvantages of each approach. Finally, we will discuss the new mass-spectrometric method based on micro-sampling and using atmospheric solid analysis probe (ASAP). T2 - Future of the Past CY - Torun, Poland DA - 14.06.2023 KW - Ink analyses KW - Spectroscopy KW - Mass spectroscopy PY - 2023 AN - OPUS4-58882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanaris, Orestis A1 - Schreiber, Frank T1 - Consequences of tolerance to disinfectants on the evolution of antibiotic resistance in E. coli N2 - Biocides are used as disinfectants and preservatives; one important active substance in biocides is benzalkonium chloride (BAC). BAC-tolerant bacterial strains can survive short treatments with high concentrations of BAC. BAC tolerance and resistance have been linked to antibiotic resistance. Here, the selection dynamics between a BAC-tolerant Escherichia coli strain and a sensitive wild type were investigated under four conditions: in the absence of antibiotics and in the presence of three different sub-inhibitory concentrations of the antibiotic ciprofloxacin in liquid cultures. The wild type was selected over the BAC-tolerant strain in the absence of antibiotics, while the BAC-tolerant strain was selected over the wild type at all ciprofloxacin concentrations investigated, with a minimum selection concentration (MSC) of 1/10th of the minimum inhibitory concentration (MIC) of the wild type. Furthermore, the evolvability of resistance of the two strains to inhibitory concentrations of ciprofloxacin was assessed by performing a serial dilution evolution experiment with gradually increasing ciprofloxacin concentrations. The wild type had a higher probability to develop resistance to ciprofloxacin than the tolerant strain. By the end of the evolution experiment both strains evolved to grow at the highest ciprofloxacin concentration investigated, which was 2048 ×MIC of the wild type. The importance of these results is highlighted by the fact that concentrations of ciprofloxacin well above the calculated MSC can be found in environmental samples such as hospital wastewaters and livestock slurry. In turn, BAC is used as a disinfectant in the same settings. Thus, the selection of BAC-tolerant strains at sub-inhibitory concentrations of ciprofloxacin can contribute to the stabilization and spread of BAC-tolerance in natural populations. The prevalence of such strains can impair the effects of BAC disinfections. T2 - µClub seminar series CY - Berlin, Germany DA - 15.12.2023 KW - Antimicrobial resistance PY - 2023 AN - OPUS4-59222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Mechanochemical remediation of PFAS in soils – Does it work? N2 - Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. These approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GC-MS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well as the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy. T2 - Baltic Sea PFAS Network Coffee Session CY - Online meeting DA - 25.08.2023 KW - Mechanochemical treatment KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Remediation KW - X-ray absorption near-edge structure (XANES) spectroscopy PY - 2023 AN - OPUS4-58114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schraut, Katharina A1 - Adam, Christian A1 - Adamczyk, Burkart A1 - Simon, Sebastian A1 - von Werder, Julia A1 - Meng, Birgit A1 - Stephan, Dietmar T1 - Production of an alite-rich material from reduced basic oxygen furnace slags N2 - Basic oxygen furnace slag (BOFS) is a by-product of steelmaking of which about 10.4 Mt are produced annually in the EU. BOFS is mostly used in road construction, earthwork and hydraulic engineering. However, in this use, the iron bound in BOFS is lost and the opportunity to produce higher value products from BOFS is forgone. In recent decades, many researchers have investigated the production of both Portland cement clinker and crude iron from BOFS via a thermochemical reductive treatment. The reductive treatment of liquid BOFS causes a reduction of iron oxides to metallic iron, which separates from the mineral phase due to its higher density and can be recovered. An advantage of this process is that simultaneously the chemical composition of the reduced BOFS is adapted to that of Portland cement clinker and the hydraulic reactive mineral alite (Ca3SiO5) is formed. In this study, German BOFS was reduced in a small-scale electric arc furnace and a low-iron mineral product rich in alite was produced. Despite a chemical and mineralogical composition similar to that of Portland cement clinker, the reduced BOFS produced less heat of hydration, and its reaction was delayed compared to Portland cement. However, adding gypsum accelerated the hydration rate of the reduced BOFS. Further research to improve the hydraulic properties of the reduced BOFS is essential. If successful, the production of a hydraulic material and crude iron from BOFS could have economic and ecological benefits for both the cement and steel industry. T2 - GeoBerlin 2023 CY - Berlin, Germany DA - 04.09.2023 KW - BOFS KW - Alite KW - Hydraulic reactivity PY - 2023 AN - OPUS4-58206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Souza Filho, I. A1 - Adam, Christian T1 - Fundamentals of the hydrogen plasma reduction of iron ores N2 - Hydrogen plasma treatment of iron ores or iron oxide containing wastes can be an efficient option to produce green iron e.g. for steel production. This way iron oxide is reduced to metallic iron in the liquid form by the highly reactive species that are formed in a hydrogen plasma. Hydrogen plasma can be used at the same time to remove undesired gangue elements. The presentation shows the experimental setup, shows first results of iron ore reduction by hydrogen plasma and gives an outlook for industrial application of the technology. T2 - European Academic Symposium on EAF steelmaking (EASES 2023) CY - Oulu, Finland DA - 05.06.2023 KW - Hydrogen KW - Plasma KW - Reduction PY - 2023 AN - OPUS4-57626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Investigation of per and polyfluoroalkyl substances (PFAS) in soils and groundwater through fluorine K-edge XANES spectroscopy – potential for collaboration N2 - Per- and polyfluoroalkyl substances (PFAS) are a group of anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination. In this presentation the advantages of fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy for various environment samples are shown. T2 - SESAME-Germany Info Day CY - Hamburg, Germany DA - 21.04.2023 KW - Soil KW - Per- and Polyfluoroalkyl substances (PFAS) KW - Synchotron KW - X-ray absorption near-edge structure (XANES) spectroscopy PY - 2023 AN - OPUS4-57365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Die Spannungsrissbeständigkeit von Kunststoffdichtungsbahnen aus PE-HD und die Zulassungsrichtlinie für Schutzschichten N2 - Kunststoffdichtungsbahnen (KDB) aus PE-HD (Polyethylen hoher Dichte) werden häufig zur Abdichtung von Bauwerken in der Geotechnik verwendet. Diese Produkte werden aus einem Kunststoff mit relativ komplexer Zusammensetzung hergestellt. Um eine Aussage über die Haltbarkeit von KDB aus PE-HD treffen zu können, muss das Materialverhalten berücksichtigt werden. In diesem Zusammenhang sind die wichtigsten Aspekte der Dauerhaftigkeit die Spannungsrissbeständigkeit und die Beständigkeit gegen Oxidation. Verschiedene PE-Sorten weisen eine unterschiedliche Spannungsrissbeständigkeit auf. Um dieser Eigenschaft von PE-HD zu begegnen, werden nur KDB aus sehr hochwertigen Rohstoffen zugelassen. Auf der anderen Seite werden hohe Anforderungen an die umgebenden Schichten, wie Auflager und Schutzschicht gestellt, um möglichst geringe Spannungen zu erzeugen und damit Dehnungen die Dehnungen der KDB gering zu halten. Bestimmte Medien, die bei den betreffenden Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Im Folgenden sollen die Zusammenhänge in Kürze dargestellt werden. Darüber hinaus sollen Diskussionen und Änderungen der Zulassungsrichtlinie für Schutzschichten im und durch den Fachbeirat vorgestellt werden. T2 - 19. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 14.03.2023 KW - Deponie KW - Kunststoffdichtungsbahn KW - Spannungsrissbeständigkeit PY - 2023 AN - OPUS4-57195 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Brandhorst, Antonia A1 - Nitsche, Sarah A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Gorbushina, Anna T1 - The roles of DHN melanin and the stress-activated MAP kinase in the rock inhabitant Knufia petricola N2 - Black fungi/yeasts exhibit high stress tolerance, yeast‑like or meristematic growth, and constitutive 1,8-dihydroxynaphthalene (DHN) melanin formation. Due to their slow growth, robust cell walls and the lack of sexual cycles and genetic tools, the underlying mechanisms of their phenotypic traits have remained largely unexplored. Using recently developed genetic tools, it is now possible to manipulate the genome of the rock-inhabiting model fungus Knufia petricola. Thus, gene functions and the cell biology of black fungi can be studied using CRISPR/Cas9-based genome editing and live-cell imaging with genetically encoded fluorescent proteins. Here, we are addressing the question to which extent constitutive pigment formation (melanin and carotenoids) and responses mediated by the stress-activated mitogen-activated protein (MAP) kinase contribute to the observed extremotolerance of K. petricola. The mutations of pks1, phs1 and both genes result in melanin-free (pink), carotenoid-free (black) and pigment-free (white) strains, respectively. The other putative melanogenic genes were identified in the genome, deleted to confirm their involvement in DHN melanogenesis and co-expressed in Saccharomyces cerevisiae for reconstruction of the synthesis pathway. Sak1 encoding the stress-activated MAP kinase was deleted in the wild-type and different pigment-deficient backgrounds. Growth of the obtained single, double and triple deletion mutants was tested by droplet tests on media supplemented with different stress-inducing agents. The Δsak1 mutants show slightly reduced growth rates even without environmental pressure and are hypersensitive to different stresses: e.g. osmotic, oxidative, membrane, pH and heat stress. Melanin-free Δsak1 mutants are more sensitive than black Δsak1 mutants to some but not all stress conditions, suggesting that melanin and the SAK1 pathway have complementary roles in protecting K. petricola from stress. T2 - 16th European Conference on Fungal Genetics CY - Innsbruck, Austria DA - 05.03.2023 KW - Black fungus KW - Extremotolerance KW - Pigments PY - 2023 AN - OPUS4-57147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - BEMMA als Auswahlkriterium für Vitrinenbaumaterialien N2 - BEMMA steht für Bewertung von Emissionen aus Materialien für Museumsausstattungen. Es ist die Kurzbezeichnung für ein Schema/Verfahren zur Untersuchung und Bewertung flüchtiger organischer Verbindungen aus Werkstoffen, die im mittelbaren Kontakt mit historischen Materialien des Kunst- und Kulturgutes stehen. Ergebnisse der Untersuchungen seit ca. 2010 bis 2017 werden präsentiert und diskutiert. T2 - Ringvorlesung der HTW Analyse und Wahrnehmung: Kulturgut erforschen und erhalten CY - HTW Berlin, Germany DA - 16.01.2018 KW - Museumsvitrine KW - VOC-Emissionen KW - BEMMA Bewertung PY - 2018 AN - OPUS4-43828 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - Zertifizierung emissionarmer Materialien für Museumsvitrinen N2 - Anregungen aus dem N.i.Ke.-Workshop 2017 und künftige Anforderungen. BEMMA steht für Bewertung von Emissionen aus Materialien für Museumsausstattungen. Es ist die Kurzbezeichnung für ein Schema/Verfahren zur Untersuchung und Bewertung flüchtiger organischer Verbindungen aus Werkstoffen, die im mittelbaren Kontakt mit historischen Materialien des Kunst- und Kulturgutes stehen. Hier wird der Status-Quo des Erreichten dargestellt. Wie wird das Schema in der Museumsöffentlichkeit wahrgenommen und seine Akzeptanz. T2 - BZS-Beirat CY - BAM, Berlin, Germany DA - 19.01.2018 KW - BEMMA KW - Museumsvitrinen KW - VOC-Emissionen PY - 2018 AN - OPUS4-43860 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Even, Morgane A1 - Wilke, Olaf A1 - Kalus, Sabine A1 - Schultes, P. A1 - Hutzler, C. A1 - Luch, A. T1 - Formaldehyde Emissions from Wooden Toys: Method Comparison and Exposure Assessment N2 - Formaldehyde is considered as carcinogenic and is emitted from particleboards and plywood used in toy manufacturing. Currently, the flask method is frequently used in Europe for market surveillance purposes to assess formaldehyde release from toys, but its concordance to levels measured in emission test chambers is poor. Surveillance laboratories are unable to afford laborious and expensive emission chamber testing to comply with a new amendment of the European Toy Directive; they need an alternative method that can provide reliable results. Therefore, the application of miniaturised emission test chambers was tested. Comparisons between a 1 m3 emission test chamber and 44 mL microchambers with two particleboards over 28 days and between a 24 L desiccator chamber and the microchambers with three puzzle samples over 10 days resulted in a correlation coefficient r2 of 0.834 for formaldehyde at steady state. The correlation between the results obtained in microchambers vs. flask showed a high variability over 10 samples (r2: 0.145), thereby demonstrating the error-proneness of the flask method in comparison to methods carried out under ambient parameters. An exposure assessment was also performed for three toy puzzles: indoor formaldehyde concentrations caused by puzzles were not negligible (up to 8 μg/m3), especially when more conservative exposure scenarios were considered. T2 - OE conference CY - Online meeting DA - 23.03.2021 KW - Formaldehyde KW - Wooden toys PY - 2021 AN - OPUS4-52330 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Even, Morgane A1 - Wilke, Olaf A1 - Kalus, Sabine A1 - Schultes, P. A1 - Hutzler, C. A1 - Luch, A. T1 - Formaldehydemissionen aus Holzspielzeug: Methodenvergleich und Expositionsabschätzung N2 - Formaldehyd gilt als krebserregend und wird von Spanplatten und Sperrholz emittiert, die bei der Spielzeugherstellung verwendet werden. Die Untersuchungsänter benötigen eine wirtschaftliche und zuverlässige Methode. Die Anwendung miniaturisierter Emissionsprüfkammern wurde getestet und mit größeren Emissionsprüfkammern und die Flaschenmethode verglichen. Eine Expositionsabschätzung wird auch vorgestellt. T2 - 28. WaBoLu-Innenraumtage CY - Online Meeting DA - 10.05.2021 KW - Formaldehyd KW - Emission KW - Spielzeug KW - Methoden PY - 2021 AN - OPUS4-52628 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Even, Morgane A1 - Wilke, Olaf A1 - Kalus, Sabine A1 - Schultes, P. A1 - Hutzler, C. A1 - Luch, A. T1 - Formaldehyde emissions from wooden toys: Method comparison and exposure assessment N2 - This study shows that formaldehyde Emission results in micro-scale emission chambers are comparable with results in bigger chambers both for particle boards and wooden toys. On the contrary, the WKI flask method was leading to more variable results depending on sample geometry. Thus, microchambers could be used for reliable routine market surveillance. An exposure assessment led to noticeable formaldehyde indoor air concentration values, pointing out the need for an effective Surveillance of such samples. T2 - Indoor Air 2020: The 16th conference of the international society of indoor air quality and climate CY - Online meeting DA - 01.11.2020 KW - Volatile organic compounds KW - Consumer products KW - WKI flask method KW - Emission chambers KW - Market surveillance PY - 2020 AN - OPUS4-52024 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Contaminants of Emerging Concern from Materials and Products: Measurement and Evaluation N2 - Test chamber measurements are an important tool to improve indoor air quality and occupational safety. Test chamber measurements are possible for a wide range of materials, products and technologies. Determination of concerning contaminants is important to ensure good indoor air quality. The detection of concerning contaminants depends on the approriate sampling and analysis. T2 - Webinar BAM-University of Birmingham CY - Online meeting DA - 24.02.2021 KW - Emerging Contaminants KW - Emission Test Chamber KW - Thermal Extraction KW - Thermal Desorption PY - 2021 AN - OPUS4-52262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -