TY - JOUR A1 - Willms, Thomas A1 - Kryk, Holger A1 - Hampel, Uwe T1 - An improved method for the analysis of the reaction products of the partial isobutane oxidation by gas chromatography using a green solvent N2 - In the present work, an improved GC/MS method for the analysis of the reaction products of the non-catalytic partial oxidation of isobutane at a starting temperature of 25°C has been developed and compared to a previously published method. Two green GC-solvents (dimethyl carbonate (DMC), diethyl carbonate (DEC)) and several internal standards (hexane, benzene, toluene, DEC) have been tested. The separation of the products at low retention times (methanol, isobutane, isobutene) could be significantly improved. For the liquid main products t-butyl hydroperoxide (TBHP), di-t-butyl peroxide (DTBP), t-butanol (TBA), propanone and most trace products (isopropanol, isobutanal, methyl formate, isopropyl formate, t-butyl formate and some acetates – 24 compounds in total), a coefficient of determination CoD > 0.999 has been achieved. For all weighing and GC/MS measurements uncertainties have been calculated. The peaks of the peak pair t-butyl formate (CoD >0.999) and isobutanol (CoD >0.99), have been simulated and used for calibrations. DEC gave a decomposition of TBHP on the column. With DMC, a problem of peak purity of TBHP appeared but could be resolved. The use of the green solvent DMC, compared to also studied traditional solvents like heptane and toluene, proved to be very beneficial, since it also permitted to determine polar compounds, e. g. carbon dioxide and formic acid. KW - GC/MS KW - Green solvent KW - Method development KW - Peroxide KW - Measurement uncertainties KW - Oxidation products KW - Simulation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-632026 DO - https://doi.org/10.1016/j.chroma.2025.465892 SN - 0021-9673 VL - 1753 SP - 1 EP - 16 PB - Elsevier CY - Amsterdam AN - OPUS4-63202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf A1 - Poelke, Birte A1 - Klein, Luise A1 - Rohloff, Alexander A1 - Hoffmann, Holger T1 - Initial VOC Emissions from Consumer Products Determined in Micro-Scale Test Chambers: Results of a Round Robin Test N2 - Emissions of volatile organic compounds (VOCs) from consumer products may have a negative impact on indoor air quality, potentially also affecting human wellbeing. Since consumers may be exposed to these VOCs immediately after e.g. unwrapping of newly purchased products, reliable analytical methods are needed to determine air concentration profiles in the early phase of VOC emissions. Concerning typical sample sizes of consumer products, micro-scale test chambers (μ-chambers) were considered suitable for this purpose. In addition, compared to medium- or large-scale test chambers, μ-chambers require lower initial investment and operational costs, and offer options for emissions screenings where higher sample throughput is essential. For these reasons, a μ-chamber-based method to determine initial concentrations of VOCs emitting within the first hours of simulated product use was developed. The chamber air was frequently sampled on desorption tubes loaded with Tenax® TA, followed by quantification of emitted VOCs via thermal desorption gas chromatography mass spectrometry (TD-GC-MS). The method was assessed in a round robin test involving eight participating laboratories from 2 countries. Pieces of a rain poncho (sample area A: 2.01·10-4 m2) emitting cyclohexanone, phenol, 2-ethylhexanol, naphthalene and isophorone in significant concentrations were distributed as sample material. Each laboratory conducted triplicate emission tests over a period of 48 h in μ-chambers with volumes of 44 or 114 mL. The loading factors L of 4.57 m2·m-3 (44 mL) or 1.76 m2·m-3 (114 mL) and air flow rates of 24 mL·min-1 resulted in area-specific air flow rates q of 7.17 m3·m-2·h-1 in both chamber types. The temperature was set to 23°C and, if possible, relative humidity was set to approx. 50%. The chamber air was sampled after 0.5, 1, 2, 4, 24 and 48 hours. In addition, to assess the analytical performance, each participating laboratory received two analyte-spiked Tenax® TA-loaded desorption tubes for quality control (QC). Very low relative standard deviations (11–17%) were obtained for the QC test. The results of the emissions tests in the early phase (0.5–4 h) were also adequate, with acceptable z scores (|z|≤2.00) received by six to seven participating laboratories. All eight laboratories obtained acceptable z scores after the longer sampling periods (24 and 48 h). Hence, the inter-laboratory comparability of the results obtained with the developed μ-chamber method was successfully confirmed. T2 - Healthy Buildings Europe 2025 CY - Reykjavik, Iceland DA - 08.06.2025 KW - VOC Emissions KW - Consumer Product KW - Test Chamber KW - Round Robin Test PY - 2025 AN - OPUS4-63706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tang, Chi-Long A1 - Seeger, Stefan A1 - Röllig, Mathias T1 - Improving the comparability of FFF-3D printing emission data by adjustment of the set extruder temperature N2 - Fused filament fabrication (FFF) is a material extrusion-based technique often used in desktop 3D printers. Polymeric filaments are melted and are extruded through a heated nozzle to form a 3D object in layers. The extruder temperature is therefore a key parameter for a successful print job but also one of the main emission driving factors as harmful pollutants (e.g., ultrafine particles) are formed by thermal polymer degradation. The awareness of potential health risks has increased the number of emission studies in the past years. However, studies usually refer their calculated emission data to the printer set extruder temperature for comparison purposes. In this study, we used a thermocouple and an infrared camera to measure the actual extruder temperature and found significant temperature deviations to the displayed set temperature among printer models. Our result shows that printing the same filament feedstocks with three different printer models and with identical printer set temperature resulted in a variation in particle emission of around two orders of magnitude. A temperature adjustment has reduced the variation to approx. one order of magnitude. Thus, it is necessary to refer the measured emission data to the actual extruder temperature as it poses a more accurate comparison parameter for evaluation of the indoor air quality in user scenarios or for health risk assessments. KW - Ultrafine particles KW - Infrared thermography KW - Thermocouple KW - Indoor air quality KW - FFF-3D printer PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-572842 DO - https://doi.org/10.1016/j.aeaoa.2023.100217 VL - 18 SP - 100217 PB - Elsevier Ltd. CY - Amsterdam, Niederlande AN - OPUS4-57284 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tang, Chi-Long A1 - Seeger, Stefan T1 - Measurement of sub-4 nm particle emission from FFF-3D printing with the TSI Nano Enhancer and the Airmodus Particle Size Magnifier N2 - The emission of ultrafine particles from small desktop Fused Filament Fabrication (FFF) 3D printers has been frequently investigated in the past years. However, the vast majority of FFF emission and exposure studies have not considered the possible occurrence of particles below the typical detection limit of Condensation Particle Counters and could have systematically underestimated the total particle emission as well as the related exposure risks. Therefore, we comparatively measured particle number concentrations and size distributions of sub-4 nm particles with two commercially available diethylene glycol-based instruments – the TSI 3757 Nano Enhancer and the Airmodus A10 Particle Size Magnifier. Both instruments were evaluated for their suitability of measuring FFF-3D printing emissions in the sub-4 nm size range while operated as a particle counter or as a particle size spectrometer. For particle counting, both instruments match best when the Airmodus system was adjusted to a cut-off of 1.5 nm. For size spectroscopy, both instruments show limitations due to either the fast dynamics or rather low levels of particle emissions from FFF-3D printing in this range. The effects are discussed in detail in this article. The findings could be used to implement sub-4 nm particle measurement in future emission or exposure studies, but also for the development of standard test protocols for FFF-3D printing emissions. KW - Air pollution KW - Ultrafine particles KW - Sub-4nm particles KW - FFF-3D printing KW - Emission testing PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-595952 DO - https://doi.org/10.1080/02786826.2024.2320430 SN - 0278-6826 VL - 58 IS - 6 SP - 644 EP - 656 PB - Taylor & Francis CY - London AN - OPUS4-59595 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long T1 - Sub-4 nm particles from FFF-3D printing measured with the TSI 1 nm CPC and the Airmodus A11 nCNC N2 - Concerns have been raised as Fused Filament Fabrication (FFF) desktop 3D printer emits harmful ultrafine particles (dP < 100 nm) during operation in indoor spaces. However, the vast majority of previous emission studies have neglected the possible occurrence of sub-4 nm particles by using conventional condensation particle counter (CPC) for detection. Thus, the total particle emission could be systematically underestimated. This study has compared two diethylene glycol (DEG) based instruments to evaluate their suitability for measuring organic FFF particles in the sub-4 nm size range either as particle counter or as a particle size spectrometer. T2 - European Aerosol Conference 2024 CY - Tampere, Finland DA - 25.08.2024 KW - Air pollution KW - Emission testing KW - FFF-3D printing KW - Sub-4nm particles KW - Ultrafine particles PY - 2024 AN - OPUS4-60930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long T1 - Minimizing the FFF-3D printer hardware bias on particle emission by adjustment of the set extruder temperature N2 - Fused filament fabrication (FFF) on desktop 3D printers is a material extrusion-based technique often used by educational institutions, small enterprises and private households. Polymeric filaments are melted and extruded through a heated nozzle to form a 3D object in layers. The extrusion temperature is therefore a key parameter for a successful print job, but also one of the main driving factors for the emission of harmful air pollutants, namely ultrafine particles and volatile organic gases, which are formed by thermal stress on the polymeric feedstock. The awareness of potential health risks has increased the number of emission studies in the past years. However, the multiplicity of study designs makes an objective comparison of emission data challenging because printer hardware factors such as the actual extruder temperature (TE) and also feedstockspecific emissions are not considered. We assume that across the market of commercial low- and mid-price FFF printers substantial deviations between actual and set extruder temperatures exist, which have a strong effect on the emissions and hence may bias the findings of exposure studies. In our last publication, we presented a standardized feedstock-specific emission test method and showed that for each investigated feedstock an increase in actual extruder temperature was accompanied by an increase in particle emissions (Tang and Seeger, 2022). Therefore, any systematic discrepancy between set and actual extruder temperature matters. In this study, we used a thermocouple and an infrared camera to measure the actual extruder temperatures at different heights. We found significant under- and overestimation of the actual extruder temperatures by the respective set temperatures in three commercial printers. This caused a broad variation of the measured total numbers of emitted particles (TP), even when the same feedstock was operated. For the determination of TP, we followed the DE-UZ 219 test guideline. In a second round we repeated the tests with all printers adjusted to exactly the same extruder temperatures, i.e., to TE=230°C for ABS and TE=210°C for PLA. All measurements were conducted in a 1 m³ emission test chamber. Particle emissions in the size range between 4 nm and 20 μm were detected. Printing on three different printer models without temperature adjustment resulted for each of the investigated feedstocks in a variation in TP of around two orders of magnitude. After temperature adjustment, this was substantially reduced to approx. one order of magnitude and hence minimizes the bias of printer hardware on the emissions. Our findings suggest that adjustment of the extruder temperature should be mandatory in emission testing standards. It also poses a more accurate benchmark and provides more reliable emission data for evaluation of indoor air quality or for health risk assessments. In addition, a proper temperature setting is in the interest of the user. Some commercial FFF printers may have a higher actual extruder temperature than displayed and unintended overheating may not only impair the print quality but may cause unnecessarily increased exposure to particle emissions. T2 - European Aerosol Conference 2023 CY - Málaga, Spain DA - 03.09.2023 KW - Ultrafine particles KW - Thermal imaging KW - 3D printing KW - Indoor air quality KW - Emission testing PY - 2023 AN - OPUS4-58258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Taghavi Kalajahi, Sara A1 - Misra, Archismita A1 - Koerdt, Andrea T1 - Nanotechnology to mitigate microbiologically influenced corrosion (MIC) N2 - Microbiologically influenced corrosion (MIC) is a crucial issue for industry and infrastructure. Biofilms are known to form on different kinds of surfaces such as metal, concrete, and medical equipment. However, in some cases the effect of microorganisms on the material can be negative for the consistency and integrity of the material. Thus, to overcome the issues raised by MIC on a system, different physical, chemical, and biological strategies have been considered; all having their own advantages, limitations, and sometimes even unwanted disadvantages. Among all the methods, biocide treatments and antifouling coatings are more common for controlling MIC, though they face some challenges. They lack specificity for MIC microorganisms, leading to cross-resistance and requiring higher concentrations. Moreover, they pose environmental risks and harm non-target organisms. Hence, the demand for eco-friendly, long-term solutions is increasing as regulations tighten. Recently, attentions have been directed to the application of nanomaterials to mitigate or control MIC due to their significant antimicrobial efficiency and their potential for lower environmental risk compared to the conventional biocides or coatings. Use of nanomaterials to inhibit MIC is very new and there is a lack of literature review on this topic. To address this issue, we present a review of the nanomaterials examined as a biocide or in a form of a coating on a surface to mitigate MIC. This review will help consolidate the existing knowledge and research on the use of nanomaterials for MIC mitigation. It will further contribute to a better understanding of the potential applications and challenges associated with using nanomaterials for MIC prevention and control. KW - Microbiologically influenced corrosion (MIC) KW - Biofilm KW - Biofouling KW - Nanobiocide KW - Nanocoating PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-599335 DO - https://doi.org/10.3389/fnano.2024.1340352 SN - 2673-3013 VL - 6 SP - 1 EP - 25 PB - Frontiers Media CY - Lausanne AN - OPUS4-59933 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strzelczyk, Rebecca T1 - Zeolites loaded with VOCs as reference for material emissions testing N2 - Nowadays, people spend most of their time indoors. Thus, a good indoor air quality is important. Emissions of volatile organic compounds (VOCs) from furniture and building materials can cause health complaints1. Quantitative VOC-emission testing is carried out under standardized conditions in emission test chambers. In the presented project an emission reference material (ERM) is developed that emits a defined mixture of VOCs which is required for quality assurance and -control (QA/QC) measures. Porous materials (e.g zeolites, activated carbons, MOFs or aerogels) are used as reservoir materials and impregnated with VOC. The porous materials are selected, among others, by their pore size, pore size distribution, polarity and availability. Due to their regular pore structure zeolites are tested at first. For a prediction of the emission profile, the ERM is supposed to exhibit a constant emission rate over time. The aim is a stability of ≤ 10 % change in the emission rate over a minimum of 14 days. Method For impregnation, the material is placed into an autoclave inside a rotatable basket. The VOC is added and the autoclave is closed. Afterwards, CO2 is inserted. The closed system is then heated to the supercritical point of CO2 (31 °C, 73.75 bar). In this state, the CO2 acts as solvent for the VOC. By rotating the basket, the distribution of the VOC is ensured. After a few minutes, the pressure is decreased slowly and the CO2 is released. For the determination of the emission profile, the impregnated sample is placed into an emission test chamber. These chambers can be operated either with dry or humid air (50 ± 5 % rel. humidity). Every second to third day, air samples are taken and analyzed by gas chromatography. For an ideal impregnation, several different pressures and temperatures as well as impregnation times are tested. Results Two zeolite materials tested in dry air conditions reach emission profiles with a decrease of less than 10 % over 14 days (heptane and toluene, respectively). Further it was discovered that smaller pellets of the same zeolite show better results than bigger particles. When the pore size of a zeolite is too small, e.g. 0.3 nm, the VOC cannot be absorbed sufficiently. The main disadvantage of zeolites is their hygroscopicity because it has a large impact on the release of VOC when they are used in emission test chambers under standardized test conditions (23 °C, 50 % rel. humidity). Activated carbons have emission profiles with a larger change over 14 days. However, the high hydrophobicity allows measurements in humid air conditions which was not possible with the before mentioned hygroscopic zeolites. It is possible to impregnate powdered materials as well, and thus powdered non-hygroscopic (n.h.) zeolites were impregnated. Their emission profiles are comparable to those of the activated carbons. The use of methylated hygroscopic zeolites with a decrease in hygroscopicity did not yield successful emission measurements. The change over 14 days is calculated only for the stable phase (~250–300 h). The desired stability of ≤ 10 % change of the emission rate over 14 days could already be reached under dry testing conditions. Further investigations under humid conditions show that zeolites with high Si/Al-ratios are non-hygroscopic and comparable to activated carbons (20–30 % change). The next step is to reduce the change in the emission rate of these materials to the aimed ≤ 10 % over 14 days. T2 - Deutsche Zeolithtagung CY - Jena, Germany DA - 28.02.2024 KW - VOC KW - Emission KW - Quality assurance KW - Reference material KW - Zeolite PY - 2024 AN - OPUS4-59843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Steger, Simon A1 - Stege, H. A1 - Bretz, S. A1 - Hahn, Oliver ED - Tomasin, P. T1 - Disclosing glittering and sparkling effects in 20th-century reverse glass paintings: a study of metallic pigments and metal foils by means of in situ XRF and DRIFTS analysis N2 - This work presents a spectroscopic study of metallic pigments and metal foils used in reverse glass paintings that were created between 1912 and 1954. Metallic pigments induce a notable sparkling effect by means of the lateral incidence of light, whereas metal foils enhance the gloss and create a glittering effect when the painting is viewed in reflected light. Both effects were desired features especially in modern reverse paintings on glass and applied by artists in manifold creative manner. The paper gives an overview on the composition of the metalfoils and metal pigments in 14 works as determined in situ by X-ray spectrometry. Metal foils made of tin, brass, aluminium and silver were found in nine paintings. Gold imitating Cu-Zn pigments in different hues and with various Cu/Zn net intensity ratios were recorded for six paintings. Silvery pigments were identified mainly as Al pigments, but also as Cu-Zn-Ni alloy in one case. Other uncommon metallic pigments were detected in Arlequin vindicatif (c. 1925) by Floris Jespers, who used not only Cu-Zn and Al pigments, but also brownish Cu and Cu-Zn-Sn pigments. Non-invasive diffuse reflectance infrared Fourier-transform spectroscopy (DRIFTS) was used to classify the binding media of the metallic pigments. Drying oil and natural resin probably mixed with oil were the most common binding media. A polysaccharide-based binder was found in the silvery Cu-Zn-Ni pigment of Ohne Titel (1954) by Marianne Uhlenhuth. KW - Archaeometry KW - Non-invasive analysis KW - Reverse paintings on glass PY - 2020 DO - https://doi.org/10.1016/j.culher.2020.11.008 SN - 1296-2074 VL - 48 SP - 196 EP - 204 PB - Elsevier Masson SAS CY - Amsterdam AN - OPUS4-54428 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steger, Simon T1 - Spectroscopic analysis of colourants and binders of Chinese reverse glass paintings tracing a cultural dialogue N2 - Scientific analysis based on spectroscopic methods provide essential information on the composition of colourants and binders in paintings. These results can be set in a historical context and help to confirm art historical interpretations. Proofs of certain pigments can be used for dating purposes and may reveal if the artist used not only local but also imported materials. A pilot study of two Chinese reverse glass paintings from the late 19th (Yingying and Hongniang) and early 20th centuries (The Archer) was performed using a multi-analytical approach including X-ray fluorescence (XRF), diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and Raman spectroscopy. This approach allowed the identification of the pigments and the classification of the binding media. The results reveal a combined use of traditional Chinese and imported European materials. Several pigments like cinnabar, lead white, orpiment, carbon black and copper-arsenic green (probably emerald green) were found in both paintings; red lead, artificial ultramarine blue, Prussian blue and ochre appear in at least one of the paintings. The proof of limewash (calcite and small amounts of portlandite) as a backing layer in “Yingying and Hongniang” indicates that clamshell white was also used for reverse glass paintings. Drying oil was classified as a binding media in most areas of both paintings. However, the orange background of The Archer yielded prominent bands of both proteinaceous and fatty binder. T2 - China and the West Reconsidering Chinese Reverse Glass Painting CY - Romont, Switzerland DA - 14.02.2020 KW - Reverse glass painting KW - DRIFTS KW - Raman spectroscopy PY - 2020 AN - OPUS4-50445 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Steger, Simon T1 - Non-invasive spectroscopic investigation of cultural artefacts: shedding light on modern reverse glass paintings N2 - This thesis addresses the development of a methodological approach for the non-invasive identification of colourants and for the classification of binding media in reverse glass paintings from the early 20th century. For this purpose, mobile and miniaturized devices were used to measure the paintings in situ. The methodology includes X-ray fluorescence (XRF), VIS spectroscopy (VIS), Raman spectroscopy and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). In a first step the capabilities of DRIFTS for binding media classification and pigment identification were tested. DRIFTS enables, besides Raman spectroscopy, the collection of molecular information of a substance that can be used as characteristic fingerprint spectrum. However, the simultaneous collection of both specular (surface) and diffuse (volume) reflection leads to complicated mixed DRIFT spectra, that can vary strongly for one substance depending on the dominant fraction of reflected light. Specular reflection causes several spectral distortions like inverted bands, band shifts and derivative-like features whereas pure diffuse reflections leads to an intensity enhancement of combination bands and overtones. Both specular and diffuse reflection cannot be optically separated, and their proportion depends on material properties like the absorption coefficient and the refractive index as well as on Parameters like surface roughness, porosity, grain size and angle of incidence and detection. A direct comparison of DRIFT spectra with IR spectra of other methods (e.g. transmission, ATR) is not possible, hence the creation of DRIFTS databases was needed. The next step was the complimentary utilization of Raman spectroscopy and DRIFTS for the dentification of synthetic organic colourants. Such colourants are in the further chapters called synthetic organic pigments (SOP) even when it’s not always entirely clear if they are soluble dyes or pigments that are practically insoluble in the medium in which they are incorporated. Raman spectroscopy is generally the method of choice when dealing with SOP, but fluorescence can hamper the Raman spectrum severely, inhibiting the proper identification of the pigment. DRIFTS was successfully applied and several SOP like synthetic alizarin (PR83), the yellow azo pigments (e.g. PY1) or the red and orange β-naphthol pigments (e.g. PR3) could be identified in the paintings solely by means of DRIFTS. The holistic methodological sequence was defined after the successful establishment of DRIFTS as serious analytical alternative. As the time is always the most limiting factor for in situ measurement campaigns in museums, the 9 sequence needs to be time saving but also efficient. The methodology starts with quick measurements by XRF and VIS to get a first idea of the pigment composition, followed by the validation of the results with the vibrational spectroscopies for selected points. Measurements of reverse glass paintings by Carlo Mense and Wassily Kandinsky were conducted to test the entire procedure. A high number of pigments could be identified, including several rare ones like strontium white (SrSO4), PR60 and PB52. The binding media were classified using the previously recorded references. The results were set in the art historian context and were discussed in a multidisciplinary way. The influence of Asian art, especially of Chinese reverse glass paintings as source of inspiration for artists of the “Blauer Reiter” collective (e.g. Wassily Kandinsky, Gabriele Münter, Franz Marc und Heinrich Campendonk) is shown. Non-invasive measurements of two Chinese reverse glass paintings from the late 19th and early 20th century were conducted, enabling a comparison of the palettes of Chinese and European painters. The Chinese palette includes heavy use of red lead and orpiment, pigments that were hardly sed in Europe anymore. More modern pigments like zinc white, cadmium yellow, viridian, chromates, cobalt blues or SOP were not found at all in the Chinese paintings. KW - Reverse glass painting KW - Raman spectroscopy KW - DRIFTS KW - Non invasive analysis PY - 2020 SP - 12 EP - 104 CY - Hamburg AN - OPUS4-51160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schuehle, Florian T1 - Quality assured uptake rates for passive sampling of indoor air VOCs N2 - Generation of experimental uptake rates (UR) for > 70 VOCs (7d /100 μg m-3) Application in German Environmental Survey – VOC exposure assessment Assurance of transparency concerning UR generation and uncertainty creates basis for decision making and comparability of measurement results. Exemplarily the uncertainty u(UR) of toluene UR was modelled and determined statistically with own laboratory data (relative standard deviation of actively sampled test gas atmosphere – RSDa and n = 5 exposed passive samplers – RSDp) in line with EN 838 as well as from variation of literature UR – RSD UR,lit. T2 - Airmon 2022, 10th International Symposium on modern principles of air monitoring and biomonitoring CY - Bristol, UK DA - 06.11.2022 KW - IAQ KW - VOC KW - Diffusive sampling KW - Uptake rate PY - 2022 AN - OPUS4-56583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sathiyamani, S. A1 - Ngiam, S. A1 - Bonnerot, O. A1 - Jaengsawang, S. A1 - Panarut, P. A1 - Helman-Wazny, Agnieszka A1 - Colini, C. T1 - Material Characterisation of 19–20th Century Manuscripts from Northern Thailand N2 - Material analysis was carried out on four manuscripts from Northern Thailand, which included two palm-leaf manuscripts and two paper manuscripts. The two palm-leaf manuscripts MS 6 and MS 7 were found to have been written in the traditional method, wherein text was incised on the surface of the leaves, and then soot applied to the surfaces, confirmed by the identification of carbon ink. MS 7 additionally showed the presence of trace levels of iron in the ink, either from soot paste or from the stylus used for inscribing. The paper manuscript MS 3 was written in iron-gall ink, with sections written using a methyl-violet based ink while MS 4 was written in carbon ink. The paper used in the case of MS 3 was found to be machine made, while khoi fibres (Streblus asper) were used for making the paper used for MS 4. A combination of traditional and modern pigments, like molybdenum orange, was used for decorating the edges and cover. The results improved our understanding of these manuscripts in particular, and also provided us with insights about the rapid adoption of modern materials and their incorporation into the production of written artefacts from Northern Thailand in the late 19th and early 20th centuries. KW - Materials analysis KW - Paper manuscript KW - Palm-leaf manuscript KW - Writing inks PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652586 DO - https://doi.org/10.1515/res-2023-0028 SN - 0034-5806 VL - 45 IS - 2-3 SP - 117 EP - 140 PB - Walter de Gruyter GmbH AN - OPUS4-65258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rimon, Hasia A1 - Rabin, Ira ED - Fuller, R.E. ED - Lange, A. T1 - Conservation of the Dead Sea Scrolls N2 - The current state of preservation of the DSS results from the synergetic effect of various factors such as great age, post-discovery treatments, poor storage conditions, environmental influences and exhibitions. With rare exceptions, neither the initial state nor a list of the treatments performed on each DSS fragment is known. Reconstruction of the individual fragment history will have to rely upon advanced analytical techniques to identify the treatments and their effects. Management of the scrolls may be divided roughly into three periods: a) the scholarly archiving period, from 1948 to the mid-1960s; b) first attempts at conservation, from the mid-1960s to late-1980s; c) Israel Antiquities Authority Scrolls Lab, from 1991 onwards. KW - Preservation KW - Dead Sea Scrolls PY - 2023 SN - 2468-3027 VL - 3D SP - 102 EP - 105 PB - Brill CY - Leiden / Boston AN - OPUS4-58910 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Richter, Matthias A1 - Schühle, Florian T1 - Experimental determination of 7-day uptake rates for diffusive sampling of 86 volatile and semi-volatile organic compounds relevant for indoor air monitoring and investigation on their sensitivity to exposure time and indoor climate N2 - This study aimed to experimentally determine uptake rates for 86 indoor relevant volatile and semi-volatile organic compounds (VOC, SVOC) for the passive sampler type Perkin Elmer/Markes™ with Tenax® TA as sorbent, which was used in the German Environmental Survey on Health (GerES VI) carried out by the German Environmental Agency (UBA) in the years 2023-2024. For this purpose, single reference gas atmospheres of 76 pure VOCs (liquid at room temperature) and a group of 10 SVOCs and VOCs (solid at room temperature) were generated using two generation procedures. By exposing the samplers to individual components, it was ruled out that interactions in a mixture have a influence on the uptake rate. Another aspect was to precisely describe the methodology and the resulting uncertainties, as there are gaps in the literature in this regard. The selection of the compounds was based on the findings of the preceding GerES V study for which data was missing or needed to be verified. In each experiment, a number of six passive samplers was exposed to the test gas atmospheres in dynamically operated exposure chambers for seven days. The sensitivity of the uptake rates of a group of 10 selected VOCs to variations in exposure time, ambient temperature, and air humidity in a multi-component reference gas atmosphere was investigated. Here, a decrease in the uptake rate with the exposure time could be observed stabilising from the fifth day of exposure onwards. A significant effect of temperature and humidity on the uptake rate was not apparent. The determined uptake rates exhibit uncertainties of < 20 % for 71 substances, and < 10 % for 51 substances which are also in good agreement with the literature, if already published elsewhere. The quantity of investigated substances, the detailed description of the methodology used to determine the uptake rates complemented by the respective uncertainties, as well as the compilation of comparative data, contribute to a better assessment of the quality and relevance of such data, which had not been published before. KW - Indoor air quality KW - Volatile organic compounds KW - Uptake rates KW - Passive sampling KW - Tenax TA PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629913 DO - https://doi.org/10.1016/j.indenv.2025.100095 VL - 2 IS - 2 SP - 1 EP - 11 PB - Elsevier AN - OPUS4-62991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias T1 - Metrological sound reference products for quality assurance and quality control measures in material emissions testing N2 - In industrialised countries more than 80% of the time is spent indoors. Products, such as building materials and furniture, emit volatile organic compounds (VOCs), which are therefore ubiquitous in indoor air. Different VOC combinations may, under certain environmental and occupational conditions, result in reported sensory irritation and health complaints. A healthy indoor environment can be achieved by controlling the sources and by eliminating or limiting the release of harmful substances into the air. One way is to use materials proven to be low emitting. Meanwhile, a worldwide network of professional commercial and non-commercial laboratories performing emission tests for the evaluation of products for interior use has been established. Therefore, comparability and metrological traceability of test results must be ensured. A laboratory’s proficiency can be proven by internal and external validation measures that both include the application of suitable reference materials. The emission test chamber procedure according to EN 16516 comprises several steps from sample preparation to sampling of test chamber air and chromatographic analysis. Quality assurance and quality control (QA/QC) must therefore be ensured. Currently, there is a lack of suitable reference products containing components relevant for the health-related evaluation of building products. The EU-funded EMPIR project 20NRM04 MetrIAQ (Metrology for the determination of emissions of dangerous substances from building materials into indoor air) aims to develop 1) gaseous primary reference materials (gPRM), which are used for the certification of gaseous (certified) reference materials (gCRM) and 2) emission reference materials (ERM). Most commercial gas standards of indoor-relevant compounds are not certified due to the lack of primary reference materials to which the project aims to contribute. The gPRM under development is a gas-phase standard containing trace levels of VOCs in nitrogen or air from the check standard according to EN 16516 (n-hexane, methyl isobutyl ketone, toluene, butyl acetate, cyclohexanone, o-xylene, phenol, 1,3,5-trimethylbenzene) with a target uncertainty of 5 %. The gPRM can be sampled into sorbent tubes to obtain transfer standards in the form of gCRM. The well characterised ERM represents a sample of a test specimen, e.g. building material, that is loaded into the emission test chamber for a period of several days and is used to evaluate the whole emission test chamber procedure. It shall have a reproducible and temporally constant compound release of less than 10 % variability over 14 days. Different approaches for retarded VOC release, such as the encapsulation of pure compounds and the impregnation of porous materials, are being tested to reach this aim. Furthermore, the design of the ERM is accompanied by the development of a numerical model for the prediction of the emissions for each of the target VOCs. The current progress of the work on both materials will be presented. T2 - CIM 2023 - 21st International Metrology Congress CY - Lyon, France DA - 07.03.2023 KW - Indoor air quality KW - VOC KW - Materials emissions testing KW - Emission reference material KW - Quality assurance/quality control PY - 2023 AN - OPUS4-57142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias T1 - Emission reference materials for indoor air measurements N2 - In industrialised countries more than 80% of the time is spent indoors. Products, such as building materials and furniture, emit volatile organic compounds (VOCs), which are therefore ubiquitous in indoor air. VOC in combination may, under certain environmental and occupational conditions, result in reported sensory irritation and health complaints. Emission concentrations can become further elevated in new or refurbished buildings where the rate of air exchange with fresh ambient air may be limited due to improved energy saving aspects. A healthy indoor environment can be achieved by controlling the sources and by eliminating or limiting the release of harmful substances into the air. One way is to use (building) materials proved to be low emitting. Meanwhile, a worldwide network of professional commercial and non-commercial laboratories performing emission tests for the evaluation of products for interior use has been established. Therefore, comparability of test results must be ensured. A laboratory’s proficiency can be proven by internal and external validation measures that both include the application of suitable emission reference materials (ERM). For the emission test chamber procedure according to EN 16516, no artificial ERM is commercially available. The EU-funded EMPIR project MetrIAQ aims to fill this gap by developing new and improved ERMs. The goal is to obtain a material with a reproducible and temporally constant compound release (less than 10 % variability over 14 days). Two approaches were tested: the impregnation of porous materials with VOC, and the encapsulation of VOC in polymer microcapsules. Impregnation is performed with help of an autoclave and supercritical CO2. The encapsulation is done by interfacial polymerisation on VOC droplets. For both approaches, synthesis and/or material parameters were varied to obtain an optimal ERM. Findings about the optimisation of ERM generation, as well as performance of the best emission reference materials, will be presented. T2 - GAS Analysis 2024 CY - Paris, France DA - 30.01.2024 KW - Emission reference materials KW - Materials emissions test KW - VOC KW - Indoor air quality PY - 2024 AN - OPUS4-59506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira A1 - Hahn, Oliver A1 - Kaska, K. ED - Uhlirz, T1 - Why Do We Need to Study Inks? N2 - While studying the socio-geographic history of inks, division 4.5 (Analysis of cultural artefacts and assets) of the BAM (Bundesanstalt für Materialforschung und -prüfung) in Berlin together with the Centre for the Study of Manuscript Cultures in Hamburg has developed a protocol for ink analysis. It consists of a primary screening to determine the type of the ink, and a subsequent in-depth analysis using several spectroscopic techniques. Using this protocol, scientists can assist scholars in addressing a rather broad range of historical questions that cannot be answered unequivocally through scholarly research alone. Among these are investigations on collaboration between scribes and scriptoria, on the usage and annotation of manuscripts and on their path through time and space in general. This research can thus help to reconstruct the circumstances of the production of written heritage as well as their history and transmission. To facilitate the dialogue between the scholars and the scientists a simple optical tool was developed to allow the scholars to perform preliminary ink analysis required for formulation of the question that in turn can be answered by scientific in-depth investigations. In this paper, ink types and their identification method is accompanied by examples of the recent work conducted on parchment manuscripts in the Austrian National Library. T2 - Congress Visual Heritage, CHNT 23 CY - Vienna, Austria DA - 15.12.2018 KW - Ink KW - Parchment PY - 2020 SP - 1.1 EP - 1.9 CY - Wien AN - OPUS4-50242 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rabin, Ira A1 - Hahn, Oliver ED - Michel, C. ED - Friedrich, M. T1 - Detection of Fakes: The Merits and Limits of Non-Invasive Materials Analysis N2 - This paper addresses the sensitive issue of authenticating unprovenanced manuscripts of high monetary value to certify they are genuine. Over the last decade, the popularity of material studies of manuscripts using non-destructive testing (NDT) has increased enormously. These studies are held in especially high esteem in the case of suspicious writings due to the methodological rigour they are reputed to contribute to debate. We would like to stress that materials analysis alone cannot prove that an object is genuine. Unfortunately, audiences with a humanities background often tend to disregard the technical details and treat any published interpretation of instrumental analysis as an objective finding. Four examples are outlined here to illustrate what questionable contributions the natural sciences can make in describing manuscripts that have actually been forged. KW - Fakes KW - Non-invasive analysis KW - Limitations PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-517202 SN - 978-3-11-071422-7 DO - https://doi.org/10.1515/9783110714333 SN - 2365-9696 VL - 20 SP - 281 EP - 290 PB - Walter de Gruyter GmbH CY - Berlin/Boston AN - OPUS4-51720 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rabin, Ira A1 - Gordon, Nehemia A1 - Cohen, Zina T1 - Inks of the Bologna Scroll: A Preliminary Study N2 - Rotolo 2 at the Biblioteca Universitaria di Bologna, also known simply as the “Bologna Scroll,” is currently the oldest known complete Torah scroll without later replacement sheets or significant lacunae. The Bologna Scroll has some unusual scribal features. According to one opinion in the Babylonian Talmud, a Torah scroll must be written with carbon ink to be valid for liturgical use.12 The main inks of the Bologna Scroll are very black, and the inks of the marginal corrections in tiny letters are even blacker. In this study, eh inks were tested by means of XRF-spectroscopy and NIR imaging. Conreary to the expectations, the current tests have definitively determined that the Bologna Scroll was both written and corrected using multiple iron-gall inks. KW - Torah KW - Ink KW - Historic ink PY - 2024 DO - https://doi.org/10.1353/mns.2024.a945374 VL - 9 IS - 2 SP - 222 EP - 242 AN - OPUS4-62264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rabin, Ira A1 - Gordon, Nehemia A1 - Calvillo, Nelson T1 - Coloured Ruling Lines in a Fourteenth-Century Ashkenazi Torah Scroll N2 - Rabbinic halakhah required that Torah scrolls be written with relief ruling, horizontal and vertical lines scored into the writing surface. Coloured ruling with plummet or ink would make a Torah scroll invalid for liturgical use. Ruling lines on some leather fragments of early Oriental Torah scrolls give the impression of being produced with plummet or ink but may be the result of dust in the furrows of relief ruling. Erfurt 9, a fourteenth-century Ashkenazi Torah scroll, has coloured ruling, which is partial secondary re-ruling, on 13 of the 34 surviving sheets, perhaps added when the original relief ruling was difficult to see. The coloured ruling in Erfurt 9 is brown, giving it the visual appearance of iron-gall ink. However, XRF tests showed that the only meaningful metallic component in the coloured ruling was lead (Pb). Lead plummet ruling tends to have a greyish appearance. Black specks under near infrared light are consistent with minium, a lead-based red ink that can turn brown when it degrades. Partial secondary re-ruling added with minium to the original relief ruling comes as a surprise as it would have rendered Erfurt 9 unfit for liturgical use. KW - Hebrew Manuscripts KW - Ruling Lines KW - Coloured Ink PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628531 DO - https://doi.org/10.25592/uhhfdm.17169 SN - 2410-0951 VL - 10 SP - 9 EP - 32 AN - OPUS4-62853 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rabin, Ira A1 - Cohen, Zina ED - Corazzol, Giacomo ED - Fargeon, Sarah T1 - Black inks in medieval Jewish manuscripts N2 - Our aim was to obtain information about the use of different black inks in medieval Hebrew manuscripts, focusing on the question of possible preferences in the use of certain inks by different scribes. We present here an overview of the inks detected in a selection of Hebrew documents penned in the Middle East in the period from the 11th century to the 13th century. KW - Historic ink KW - Ink KW - Hebrew manuscripts KW - XRF KW - NIR PY - 2025 UR - https://books.openedition.org/ephe/2673?lang=en DO - https://doi.org/10.4000/13sug SP - 13 EP - 30 CY - Paris AN - OPUS4-65349 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rabin, Ira A1 - Caldararo, N. A1 - Rimon, H. ED - Russel, R.E. ED - Lange, A. T1 - The Role of DNA Analysis in the Study of the Biblical Manuscripts N2 - Interest in the type of skin used in scriptural materials and preparation methods increased from the nineteenth into the twentieth century. This was due partly to the number of newly discovered fragments and to the invention of new instruments and scientific procedures to identify animal skins and produce qualitative means to demonstrate specific preparation reagents and techniques. The invention of various means of analyzing the DNA of organic materials brought about a revolution in archaeology and in conservation. Difficulties in overcoming contamination of archaeological samples resulted in a number of controversies but also produced advances and improvement in the techniques of ancient DNA analysis and interpretation of results. KW - DNA KW - Dead Sea Scrolls KW - Parchment PY - 2023 SN - 2468-3027 VL - 3D SP - 120 EP - 123 PB - Brill CY - Leiden / Boston AN - OPUS4-58914 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Rabin, Ira ED - Raggetti, L. T1 - Material Studies of Historic Inks: Transition from Carbon to Iron-Gall Inks N2 - This chapter offers observations and considerations concerning black writing inks encountered in writing supports transmitting documentary and literary texts of the late Antiquity and early Middle Ages. It discusses different types of inks, the Methods of their detection and their use in different times and geographical areas. KW - Material analysis KW - Writing inks KW - Ink fingerprint PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-528057 DO - https://doi.org/10.1163/9789004444805_006 SP - 70 EP - 78 PB - Brill CY - Leiden AN - OPUS4-52805 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira ED - Ciner, P. ED - Nunez, A. T1 - Writing Materials of the Dead See Scrolls N2 - The first manuscripts from the Qumran caves were found in 1947. Within the following 10 years, clandestine and legal excavations revealed some 900 highly fragmented manuscripts from the late Second Temple period. This collection is generally known as Scrolls of the Judea Desert or Dead Sea Scrolls (DSS). For many years after their discovery, text analysis and fragmeents attribution were the main concern of the scholars dealing with the scrolls. The uncertain archaeological provenance of the larger part of the collection added an additional difficulty to the formidable task of sorting some 19000 fragments. After 60 years of scholar research the question of origin, archaeological provenance and correct attribution of the fragmenst are still hotly debated. To dtermine a possible contribution to the debate from the point of view of writing materials, we used otpical and electron microscopy, various X-ray based techniques as well as vibratiional sprectroscopy. We validated our approach with SY - based studies using the advantages of the synchroton radiation source with respect to the benchtop devices. Our laboratory studies showed that often production and storage locality could be distinguished thenks to the specific residues ("fingerprint") they left on the material. Moreover, we have diescovered that diferrent parchment production processses coexisted in the antiquity, and the resulting writing materials can readily be distinguished. T2 - 2nd International Conference on Patristic Studies CY - San Juan, Argentina DA - 28.03.2017 KW - Dead Sea Scrolls KW - Text analysis KW - Fragmented manuscripts KW - X-ray based techniques KW - Archaeological provenance PY - 2021 SN - 978-2-503-59149-0 DO - https://doi.org/10.1484/M.STR-EB.5.1211558 SN - 2566-073X VL - 0095/ 19 SP - 325 EP - 331 PB - Brepols CY - Turnhout, Belgium AN - OPUS4-54593 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Beyond Chocolate and Apricot Using Scientific Techniques to Determine the Relationship of the Inks of Codex Vaticanus N2 - Codex Vaticanus was written by multiple scribes and annotated by over thirty different hands. In the past, scholars have speculated about the relationship between the inks using highly subjective observations. For example, The scholars spoke about “apricot” and “chocolate” distigmai, arguing for their respective origins based on their visual similarity to the original ink and that of the medieval reinker, respectively. In recent decades, micro X-ray fluorescence (µXRF) has revolutionized the study of ancient and medieval cultural artifacts, making it possible to examine them using objective criteria. The application of such objective scientific measurements to ancient and medieval manuscripts will be explained with examples of how color, hue, and appearance of ink can be highly misleading. T2 - Annual Meeting of the Siciety of Biblical Literature CY - San Antonio, TX, USA DA - 18.11.2023 KW - Codex B KW - Codex Vaticanus KW - Historic ink KW - Micro-XRF PY - 2023 AN - OPUS4-61200 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Panorama of Black writing inks: From Antiquity to the Middle Ages N2 - Black writing inks in the period under consideration can be divided into three different classes: soot, tannin and iron-gall ink. The first one is a fine dispersion of carbon pigments in a water-soluble binding agent, the second one is a solution of plant extract from tree barks or gallnuts, while the third one contains both soluble and insoluble phases. This last ink is based on metal (iron) and is produced by a chemical reaction of soluble iron (II) with tannin in aqueous solution. Tracing the transition from writing inks based on carbon pigments (soot or charcoal), common in Antiquity to the iron-gall inks commonly used in the Middle Ages builds a focus of our investigative work at the BAM (Federal Institute of Material Analysis and Testing) [1-5]. With the aim of creating a detailed history of writing black inks, we worked out a non-invasive protocol to collect statistically relevant ink data from dated and localized manuscripts covering a large time span and different geographic areas. The first step of our protocol consists of the screening carried out by means of imaging in the near infrared region. The optical differences between carbon, tannin, and iron-gall inks are best recognized by comparing their response to the infrared light: carbon ink has a deep black colour, iron-gall ink becomes transparent above 1400 nm, and tannin ink disappears at about 750 nm, we have simplified the analysis using a small USB microscope with built-in NIR (940 nm) and UV (395 nm) LED in addition to an external white light source [1]. Comparing the images under white and near infrared illumination, we determine the ink typology by observing the changes in the opacity of the ink. Here, carbon-based inks show no change in their opacity when illuminated with near infrared light, while the opacity of iron-gall inks changes considerably, and tannin inks become transparent. Our own recent finding that mixed carbon / iron-gall inks were quite popular in the late Antiquity and early Middle Ages suggested to return to the conventional method using infrared light in the spectral region 1000 – 1400 nm. The presentation will show the panorama of historic inks and our attempt to follow up the transition of the inks from those based on soot to the iron-gall inks commonly used in the Middle Ages. T2 - Public lecture CY - Manchester, UK DA - 01.02.2024 KW - Ink KW - Historic ink PY - 2024 AN - OPUS4-61201 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Black writing inks: From Antiquity to the Middle Ages N2 - Tracing the transition from writing inks based on soot, common in Antiquity to the iron-gall inks commonly used in the Middle Ages builds a focus of our investigative work at the BAM and the Centre for the Studies of Manuscript Cultures (CSMC) [1-4]. With the aim of creating a detailed history of writing black inks, we worked out a non-invasive protocol to collect statistically relevant ink data from dated and localized manuscripts covering a large time span and different geographic areas. The first step of our protocol consists of the screening carried out by means of the NIR & IRR reflectography. The optical differences between carbon, tannin, and iron-gall inks are best recognized by comparing their response to the infrared light: carbon ink has a deep black color, iron-gall ink becomes transparent above 1400 nm, and tannin ink disappears at about 750 nm, we have simplified the analysis using a small USB microscope with built-in NIR (940 nm) and UV (395 nm) LED in addition to an external white light source [1]. Comparing the images under white and near infrared illumination, we determine the ink typology by observing the changes in the opacity of the ink. Here, carbon-based inks show no change in their opacity when illuminated with NIR wavelength, while the opacity of iron-gall inks changes considerably, and tannin inks become transparent. Our own recent finding that mixed carbon / iron-gall inks were quite popular in the late Antiquity and early Middle Ages suggested to return to the conventional IRR method. The presentation will show the panorama of historic inks and our attempt to follow up the transition of the inks from those based on soot to the iron-gall inks commonly used in the Middle Ages. T2 - Seminar University of Oslo CY - Oslo, Norway DA - 23.09.2022 KW - Ink KW - Historic ink PY - 2022 AN - OPUS4-61194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Unveiling the use of writing materials in Carolingian manuscripts N2 - After having been neglected for a long time, materiality is nowadays of great interest in the study of manuscripts. This allows us to explore the variety (and potential coexistence) of different inks and pigments in type and composition in their use over time and geographical area. In this presentation, we aim to contribute to their study through archaeometric analyses of black and red inks used in Carolingian manuscripts copied between the 8th and the 10th centuries. These analyses are based on an interdisciplinary strategy, bringing together knowledge from the humanities and natural sciences to understand the global use of black and red inks in the Carolingian Empire. In this regard, we adopted a non-invasive protocol that included near-infrared imaging and X-ray fluorescence spectroscopy for on-site measurements supported by historical and palaeographic analysis. The results have been collected in the framework of two projects at the University of Hamburg in close collaboration with the Bundesanstalt für Materialforschung und -prüfung, Berlin (BAM) and will be compared with several other archaeometric studies of contemporary manuscripts. T2 - Novel approaches to Digital Codicology CY - Tours, France DA - 10.05.2023 KW - Carolingian manuscripts KW - Historick inks KW - Pigments PY - 2023 AN - OPUS4-61199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Imaging micro-XRF in studies of manuscripts N2 - Availability of mobile XRF-equipment with an interaction spot of ca. 100 µm produced a revolution in the studies of manuscripts. A protocol for the use of line-scans introduced in the beginning of 2000 permitted large scale and extremely successful investigations of the medieval iron-gall inks. Here, we usually focus on a comparison of the characteristic metallic components in the inks. In our work, we encountered cases that could be adequately addressed only using large area imaging XRF. However, conducting an M6 scan on a bound manuscript or on a scroll of huge dimensions is not a simple and easy matter. In our presentation, we want to share our experience by presenting a series of the case studies, in which many an original solution was found. T2 - M6 JETSTREAM European User Meeting CY - London, GB DA - 03.04.2023 KW - Micro-XRF KW - Manuscripts KW - Imaging PY - 2023 AN - OPUS4-61198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Authentic vs. inauthentic Dead Sea Scrolls from the point of view of material analysis N2 - The paper seeks to illuminate the problem of identifying forgeries among the Dead Sea Scrolls from the point of view of material analysis. It will present the sum of our technical knowledge of the skin-based material of the Dead Sea Scrolls, which includes the original treatment of the skins and the resulting typology as well as degradation effects due to their sojourn in caves and post-discovery interventions. We will try then to list the characteristic properties that must be found in the authentic material. We will supplement the presentation with a short description of the relevant methods of material analysis and their contribution to the secure identification of inauthentic Dead Sea Scrolls. T2 - Annual Meeting of the Siciety of Biblical Literature CY - Denver, CO, USA DA - 19.11.2022 KW - Dear Sea Scrolls KW - Forgery PY - 2022 AN - OPUS4-61196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Material analysis - results N2 - The presentations describes the results obtained by material analysis of the writing materials. Their relevance in the field of digital editing and publishing is discussed. T2 - Communicating Revealed Texts: Best Practices for Born-Digital Editions Using Enhanced Imaging CY - Iowa City, IA, USA DA - 29.06.2024 KW - Writing materials KW - Manuscripts KW - Material analysis PY - 2024 AN - OPUS4-61202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Advances in Characterization of Written Heritage N2 - The session discusses three brances of teh work on the manuscripts: ink analysis, parchment analysis by proteomics (Matthew Collins) and lipids (Mélanie Roffet-Salque); revealing of hidden text using AI. The example of Vesuvium Challenge is presented and discussed by Bren Seales. T2 - Scientific Methods in Cultural Heritage Research Gordon Research Conference CY - Vaud, Switzerland DA - 07.07.2024 KW - Written Heritage KW - Vesuvius challenge KW - Proteomics KW - Lipids PY - 2024 AN - OPUS4-61203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rabin, Ira ED - Russel, R.E. ED - Lange, A. T1 - Ancient Inks N2 - In the last decade scientists and scholars have accumulated more knowledge on black ink used for writing in Antiquity and the early Middle Ages. Ready availability of non-destructive testing instruments employed in interdisciplinary projects on historic manuscripts have made it possible to determine the composition of ink and to compare it with the extant records. KW - Writing Ink KW - Antiquity PY - 2023 SN - 2468-3027 VL - 3D SP - 117 EP - 120 PB - Brill CY - Leiden / Boston AN - OPUS4-58913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Rabin, Ira ED - Russel, R.E. ED - Lange, A. T1 - Non-invasive Analytic Tools in Studies of Manuscripts N2 - Physico-chemical analyses of writing materials offer insight into various questions associated with historical, cultural, and conservational aspects of manuscript studies. The catalogue of questions that can be addressed with these methods includes authenticity, dating, the attribution of various parts of the text to different scribes and the relation between the primary and secondary texts. Similarly, preservation of the manuscripts requires knowledge of the composition of the original materials versus old repairs, identification of damage, as well as recognition of natural aging and degradation processes. The material sciences can contribute data about the chemical compositions of the writing materials, elucidation of the techniques of their production and the absolute age of organic components, as well as characterization of corrosion effects, evaluation of conservation treatment, and monitoring of the preservation state. KW - Material Analysis KW - Manuscripts PY - 2023 SN - 2468-3027 VL - 3D SP - 114 EP - 116 PB - Brill CY - Leiden / Boston AN - OPUS4-58912 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rabin, Ira ED - Binder, J. T1 - The marginal notes of Tosefta MS Erfurt N2 - Manuscript Erfurt 12 of the Tosefta (now Berlin, Staatsbibliothek, Ms. or. fol. 1220) is one of three major textual witnesses of the Tosefta. This manuscript has over 80 marginal notes which have not merited scholarly attention. This article presents a comprehensive analysis of all the marginal notes, including an evaluation of their ink composition, a palaeographic assessment of the scripts, as well as a philological assessment of their contents. Combining these methodologies differentiates between the glosses of the scribe and those added by later hands and identifies their provenance, allowing us to trace the history of the manuscript via the emendations that took place in the scholarly communities in which the manuscript was studied. One of the important outcomes of the research is an early dating of the manuscript to eleventh-century Italy, overturning the scholarly view which dates the manuscript to twelfth-century Rhineland KW - Hebrew Manuscripts KW - Ink KW - NIR KW - XRF PY - 2025 DO - https://doi.org/10.3828/jjs.2025.76.2.272 SN - 0022-2097 VL - 76 IS - 2 SP - 272 EP - 300 AN - OPUS4-64770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Black ink from antiquity to the Middle Ages N2 - Il nostro lavoro di ricerca al BAM si concentra sul passaggio dagli inchiostri a base di fuliggine, comuni nell'antichità, agli inchiostri ferro-gallici, comunemente usati nel Medioevo. Con l'obiettivo di creare una storia dettagliata degli inchiostri neri, abbiamo elaborato un protocollo non invasivo per raccogliere dati statisticamente rilevanti sugli inchiostri da manoscritti datati e localizzati che coprono un ampio arco temporale e diverse aree geografiche. Il primo passo del nostro protocollo consiste nella selezione effettuata mediante riflettografia NIR e IRR. Le differenze ottiche tra gli inchiostri a base di carbonio, tannino e ferro-gallio sono meglio riconoscibili confrontando la loro risposta alla luce infrarossa: l'inchiostro a base di carbonio ha un colore nero intenso, l'inchiostro ferro-gallico diventa trasparente al di sopra dei 1400 nm e l'inchiostro a base di tannino scompare a circa 750 nm. abbiamo semplificato l'analisi utilizzando un piccolo microscopio USB con LED NIR (940 nm) e UV (395 nm) integrati, oltre a una fonte di luce bianca esterna. Confrontando le immagini sotto illuminazione bianca e nel vicino infrarosso, determiniamo la tipologia di inchiostro osservando i cambiamenti nell'opacità dell'inchiostro. In questo caso, gli inchiostri a base di carbonio non mostrano alcuna variazione di opacità quando illuminati con lunghezza d'onda NIR, mentre l'opacità degli inchiostri ferro-gallici cambia notevolmente e gli inchiostri tanninici diventano trasparenti. La nostra recente scoperta che gli inchiostri misti carbonio/ferro-gallici erano piuttosto diffusi nella tarda antichità e nell'alto Medioevo ci ha suggerito di tornare al metodo IRR convenzionale. Il secondo passo del protocollo prevede l'analisi micro-XRF per identificare i componenti inorganici dell'inchiostro. Nel caso degli inchiostri ferro-gallici, stabiliamo le impronte digitali, ovvero i rapporti caratteristici tra i componenti vitriolici dell'inchiostro e l'elemento principale, ferro. T2 - 1° SEMINARIO di studi dottorali CY - Benevento, Italy DA - 06.10.2025 KW - Ink KW - Historic ink PY - 2025 AN - OPUS4-64773 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Ink Analysis of Relic Texts N2 - The presentation will show the multitude of black writing inks in use during the late Antiquity and early Middle Ages in Europa and the Near East and our attempt to follow up the transition of the inks from those based on soot to the iron-gall inks commonly used in the Middle Ages. Black writing inks in the period under consideration can be divided into three different classes: soot, tannin and iron-gall ink. The first one is a fine dispersion of carbon pigments in a water-soluble binding agent, the second one is a solution of plant extract from tree barks or gallnuts, while the third one contains both soluble and insoluble phases. This last ink is based on metal (iron) and is produced by a chemical reaction of soluble iron (II) with tannin in aqueous solution. Tracing the transition from writing inks based on carbon pigments (soot or charcoal), common in Antiquity to the iron-gall inks commonly used in the Middle Ages builds a focus of our investigative work at the BAM (Federal Institute of Material Analysis and Testing). In this context, we will discuss the results of the ink analysis obtained within the project “Crafting documents”. T2 - Heritage Science and Manuscripts from Antiquity and the Middle Ages CY - Oxford, United Kingdom DA - 13.11.2025 KW - Ink KW - Historic ink PY - 2025 AN - OPUS4-64772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Material analysis of afghanistan liturgical quire (ALQ) conducted at the BAM N2 - The lecture presents the results of the detailed material analysis of the inks and of the parchment of the Afghanistan Liturgical Quire (ALQ), conducted at the Bundesanstalt für Materialforschung und -Prüfung (BAM) in Berlin. Testing was conducted using the following techniques: 3-color photography, 3D-digital microscopy, scanning μ-X-ray fluorescence analysis (XRF), μ- Raman and FTIR spectroscopy. I will give a short explanation of the principles of the techniques and explain the choice of the instruments. The main task of our work at the BAM required characterization of the inks and comparison of the ink as well as the composition of parchment. For the ink characterization we have followed the protocol developed at the BAM. The standard protocol includes three non-invasive stages: a) near infrared photography (NIRR) to determine the ink type or its main component; b) X-ray fluorescence analysis (XRF) to determine a fingerprint for iron-gall inks or contaminants in carbon/plant inks; c) Raman spectroscopy if there is an indication that the inks are of a mixed type. For parchment characterization, we usually employ µ-XRF-mapping and FTIR to gain information on specific treatments experienced by the parchment during its preparation and history. T2 - 19th World Congress of Jewish Studies CY - Jerusalem, Israel DA - 04.08.2025 KW - Hebrew Manuscripts KW - Parchment KW - Ink KW - XRF KW - NIR PY - 2025 AN - OPUS4-64776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Studies of the black writing inks N2 - In recent years, the interest in the composition of the inks in papyri documents grew exponentially. Different types of inks were found in the period 4th century BCE to 7th century CE. The paper will demonstrate a simple protocol based on comparison of the ink transparency in the near infrared light and X-ray fluorescence spectroscopy. The importance of including ink composition into new catalogues and possible formats of such data will be also presented and discussed. T2 - 31st International Congress of Papyrology CY - Cologne, Germany DA - 28.07.2025 KW - Ink KW - Historic ink KW - Papyrus PY - 2025 AN - OPUS4-64777 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - Inks in Early Medieval Manuscripts from Chelles: a Scientific Study N2 - The talk will start with the overview of the ink types and the methods of their characterisation. After displaying XRF spectra of different Carolingian inks the talk will discuss Chelles collection and the labels attributed to Chelles. We will concentrate then on the study of the Chelles manuscripts preserved in Cologne, Vatican and Paris. We will show that there is a good degree of coincidence between the inks of the Chelles manuscripts and the labels attributed to Chelles. We observe unusually early use of vitriolic ink north of the Alps. T2 - Leeds International Medieval Congress (IMC 2025) CY - Leeds, United Kingdom DA - 07.07.2025 KW - Ink KW - Historic ink PY - 2025 AN - OPUS4-64778 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabin, Ira T1 - The Temple Scroll: Reconstructing an Ancient Manufacturing Practice N2 - The presentation shows the studies of ancient parchment and leather conducted by the authors within last 20 years. Presentation specifically focusses on poduction of the parchment of the Temple scroll. The practice unites the early production of modern parchment with the lost way of skin splitting. T2 - The Temple Scroll: A Research Colloquium CY - New York City, USA DA - 24.02.2025 KW - Dead Sea Scrolls KW - Parchment KW - Tanning PY - 2025 AN - OPUS4-64779 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poliakova, A. A1 - Ciotti, G. A1 - Helman-Wazny, Agnieszka A1 - Fromm, J. T1 - Phytolith assemblages from palm leaves and palm-leaf manuscripts: what is the difference and what it could mean? N2 - We studied freshly collected, dried and herbarized leaf fragments of two palms, namely Borassus flabellifer L. and Corypha umbraculifera L., most commonly used for palm-leaf manuscript (PLM) production in South (S) and Southeast Asia (SE) in order to reveal differences in their phytolith assemblages. For each of the two palms, 25 leaf samples were taken from the two Indian states of Kerala and Tamil Nadu. Dried leaf material was obtained from the fresh one by drying the leaves in air. Herbarium samples were obtained from two independent herbaria, specimen origin comprises S and SE Asia with the main focus on South India and Sri Lanka. Additionally, 25 manuscripts made of Borassus flabellifer leaves and 25 manuscripts made of Corypha umbraculifera leaves were investigated for phytoliths. All manuscripts are preliminary dated back to between the 16th and the beginning of the 20th century CE; most of them assumedly were produced in S India (Tamil Nadu and Kerala), Sri Lanka, Burma or Indonesia. Phytolith assemblages significantly differed between fresh, dry and herbarized palm leaves in comparison to PLM material, both qualitatively and quantitatively (mean r2 = - 0.61 ± 9.3 for Borassus samples and r2 = - 0.75 ± 5.3 for Corypha samples, at p &lt; 0.001). Fifty-three phytolith types described for PLM material were not observed in any of the fresh, dry or herbarized palm-leaf samples. Geographical analysis of PLM-specific phytoliths suggests that the combination of those phytoliths could be region-related. In this paper, we prove that the methods of palaeoecological reconstructions based on detailed microscopy of the PLMs surface and phytolith analysis applied in combination with methods of mathematical and computer data analysis can contribute to answer the questions posed by material codicology by revealing lost manuscript production recipes and by studying manuscript provenance in terms of the geographical origin of the artefacts. Our approach can potentially open a new perspective for palaeoecological studies expanding their traditional scope and making them applicable to a new research field. KW - Palm-leaf manuscripts KW - Material codicology KW - Palaeoecology PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652517 DO - https://doi.org/10.3389/fpls.2024.1482790 SN - 1664-462X VL - 15 SP - 1 EP - 29 PB - Frontiers Media SA AN - OPUS4-65251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöller, Renate A1 - Hahn, Oliver ED - Dora, C. ED - Fabian, C. ED - Knoche, M. ED - Linder, M. ED - Mittler, E. ED - Schmitz, W. T1 - VIS-Spectroscopy of Aztec colors. Possible application of a non-destructive analytical method N2 - VIS-spectrometry is a rapid, non- invasive, mobile method that offers a first overview of possible colorants used for painting. This is worked out in detail for European paintings and applied for artefacts and illuminated manuscripts. Manuscripts from Asia for example show colorful decoration identified to be mostly prepared with mineral pigments such as cinnabar, azurite, malachite or orpiment, which can be well confirmed by elemental analyses due to their color-giving metal ions. This is not the case for the colorants used in pictorial manuscripts from pre-Hispanic America, painted mainly with organic dyes from plants. The palette of colors used by the Aztecs is very rich due to their extensive empire and long- distance communication with vassal states liable to tributes including dyes of high quality. These include for example red cochineal, yellow zacatlaxcalli, tagetes, safflower, and achiotl, as well as blue indigo, or matlalli. T2 - Manuscripta Americana: Aufarbeitung einer Sammlung CY - Ibero-Amerikanisches-Institut, SPK DA - 14.02.2019 KW - Pigments KW - Dyes KW - Humboldt Codices KW - Non-destructive test PY - 2020 SN - 978-3-447-11511-7 SN - 0067-8236 VL - 53 SP - 35 EP - 57 PB - Harrassowitz Verlag CY - Wiesbaden AN - OPUS4-51934 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nehring, Grzegorz A1 - Gordon, Nehemia A1 - Rabin, Ira T1 - Distinguishing between seemingly identical inks using scanning μXRF and heat maps N2 - This study will present a new approach to distinguishing writing inks that have the same elemental compositions and visual appearances. The approach is based on displaying the intensity of elemental distributions as heat maps that represent data recorded with a scanning μX-ray fluorescence spectrometer. The heat maps present the data so as to facilitate digitally identifying and distinguishing between inks used to produce, correct, and reink two medieval Torah scrolls. As ritual objects, Torah scrolls had to be written in accordance with exacting standards that evolved over time. This requirement led to successive stages of modifications, sometimes over centuries. Both vitriolic and non-vitriolic inks used to modify Torah scrolls can be visually identical to each other. Furthermore, different non-vitriolic inks usually have an identical elemental composition. The solid material analysis evidence and its presentation as heat maps made it possible to discriminate between original and altered portions of text that in some cases would have been impossible. Our interdisciplinary work brought together conservation, material science, paleog-raphy, and philology to enable the identification of complex stratigraphy in multiple stages of production, correction, and reinking. ©2 0 2 2 Published by Elsevier Masson SAS. KW - Spectroscopy KW - Scanning micro-X-ray fluorescence KW - Vitriolic iron-gall inks KW - Non-vitriolic iron-gall inks KW - Heat maps KW - Torah scrolls KW - Scribal corrections PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-557271 DO - https://doi.org/10.1016/j.culher.2022.07.007 SN - 1296-2074 VL - 57 SP - 142 EP - 148 PB - Elsevier Masson SAS AN - OPUS4-55727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nehring, Grzegorz A1 - Girard, Solène A1 - Rabin, Ira T1 - Conservation and Technical Evaluation of an Early Medieval Papyrus Codex N2 - In 2005, a team of Polish archaeologists discovered three Coptic codices, two on papyrus and one on parchment, in the rubbish dump of a hermitage at Sheik Abd el-Gurna, Egypt. While the parchment codex and the remains of the bindings of the papyrus ones have been conserved, the text blocks of the papyrus codices were opened and disassembled and after being disinfected remained untouched for nearly 15 years, until the current project started. Currently, all three books are stored in the collection of the Coptic Museum in Cairo. Our team undertook the conservation of and archaeometric research on the papyrus codices. The first of the books contains the Canons of Pseudo-Basil, while the second is an Encomium of St. Pisenthios. Both codices have been palaeographically dated to the seventh-eighth centuries CE. In this paper, we describe our project and present the results of the work carried out on the Canons of Pseudo-Basil. Our work involved photography in transmitted light, measurements of the thickness of the papyrus leaves, and digital microscopy under three-light illumination. These measurements allowed us to determine the types of the inks and characterize the papyrus writing substrate. For conservation, we used a novel method developed in the Egyptian Museum in Berlin that comprises suspending papyrus folios on a translucent, extremely thin Japanese paper inside glass frames without the use of adhesives.In 2005, a team of Polish archaeologists discovered three Coptic codices, two on papyrus and one on parchment, in the rubbish dump of a hermitage at Sheik Abd el-Gurna, Egypt. While the parchment codex and the remains of the bindings of the papyrus ones have been conserved, the text blocks of the papyrus codices were opened and disassembled and after being disinfected remained untouched for nearly 15 years, until the current project started. Currently, all three books are stored in the collection of the Coptic Museum in Cairo. Our team undertook the conservation of and archaeometric research on the papyrus codices. The first of the books contains the Canons of Pseudo-Basil, while the second is an Encomium of St. Pisenthios. Both codices have been palaeographically dated to the seventh-eighth centuries CE. In this paper, we describe our project and present the results of the work carried out on the Canons of Pseudo-Basil. Our work involved photography in transmitted light, measurements of the thickness of the papyrus leaves, and digital microscopy under three-light illumination. These measurements allowed us to determine the types of the inks and characterize the papyrus writing substrate. For conservation, we used a novel method developed in the Egyptian Museum in Berlin that comprises suspending papyrus folios on a translucent, extremely thin Japanese paper inside glass frames without the use of adhesives. KW - Papyrus KW - Codex KW - Conservation KW - Iron gall ink KW - Coptic PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-570998 DO - https://doi.org/10.1080/00393630.2023.2183554 SN - 0039-3630 SP - 1 EP - 12 PB - Taylor & Francis AN - OPUS4-57099 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nehring, Grzegorz A1 - Bonnerot, Olivier A1 - Gordon, N. A1 - Rabin, Ira T1 - Writing and Correcting a Torah Scroll in Germany of the Thirteenth and Fourteenth Centuries N2 - Scientific material analysis of the elemental composition of inks from different strata of a manuscript has the potential to complement scholarly observations using palaeography and philology in reconstructing the history of the manuscript’s production, correction and repair. There are three typologically different classes of black writing inks: soot inks consist of carbon particles. KW - Manuscript studies KW - Hebrew studies KW - Ink analysis PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-540658 DO - https://doi.org/10.25592/uhhfdm.9749 VL - Comparative Oriental Manuscript Studies Bulletin 7, 2021 IS - 7 SP - 2 EP - 20 PB - Centre for the study of manuscript cultures CY - Hamburg AN - OPUS4-54065 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nehring, Grzegorz A1 - Bonnerot, Olivier A1 - Gerhardt, M. A1 - Krutzsch, M. A1 - Rabin, Ira T1 - Looking for the missing link in the evolution of black inks N2 - In the transition from carbon to iron-gall inks, the two documents from the Egyptian Museum and Papyrus Collection in Berlin with shelfmarks P 13500 and P 13501 discussed in this work present an important case. Their inks appear brownish, although they date back to the fourth and third century BCE, when carbon inks are believed to have been commonly if not exclusively used. Using imaging micro-X-ray fluorescence and infrared reflectography, we discovered that the inks in both documents contain a significant amount of copper in addition to carbon. Comparing the extant recipes for black writing inks and the experimental evidence, we suggest that these inks are a transition between the pure carbon and the iron-gall inks. Such inks may have been quite common before the production of iron-gall ink was clearly understood and established. KW - Black writing ink KW - Hellenistic KW - Papyrus KW - XRF imaging KW - NIR imaging PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-523708 DO - https://doi.org/10.1007/s12520-021-01320-5 VL - 13 IS - 4 SP - Article 71 PB - Springer AN - OPUS4-52370 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nehring, Grzegorz T1 - Breaking the limits of the non-destructive instrumental analysis of writing inks N2 - The ink analysis protocol developed through cooperation between the Bundesanstalt für Materialforschung und -prüfung in Berlin and the Centre for the Study of Manuscript Cultures at the University of Hamburg involves the use of imaging techniques for ink screening, followed by spectroscopic analysis. In our presentation, we will begin by briefly reviewing the history of writing inks and discussing the three main categories: carbon-based inks, plant, and iron-gall inks. We will address their chronology, precursors, and mixed forms, as well as the features that allow for their identification. Then, we will present the techniques we use in ink analysis, whereby we would like to highlight the limitations, advantages, and disadvantages of each approach. Finally, we will discuss the new mass-spectrometric method based on micro-sampling and using atmospheric solid analysis probe (ASAP). T2 - Future of the Past CY - Torun, Poland DA - 14.06.2023 KW - Ink analyses KW - Spectroscopy KW - Mass spectroscopy PY - 2023 AN - OPUS4-58882 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Musyanovych, A. A1 - Grimmer, Christoph A1 - Sadak, A. E. A1 - Heßling, L. A1 - Lüdicke, M. A1 - Bilsel, M. A1 - Horn, Wolfgang A1 - Richter, Matthias T1 - Polymer Capsules with Volatile Organic Compounds as Reference Materials for Controlled Emission N2 - Encapsulation of volatile organic compounds (VOCs) that could evaporate at a defined rate is of immense interest for application in emission reference materials (ERMs). Polyurethane/polyurea microcapsules with various VOC active ingredients (limonene, pinene, and toluene) were successfully produced by interfacial polymerization with Shirasu porous glass membrane emulsification in a size range between 10 and 50 μm. The effect of surfactant, VOC, monomer(s) type, and ratio has a great effect on the formulation process and morphology of capsules. The type of VOC played a significant role in the encapsulation efficiency. Due to the difference in vapor pressure and VOC/water interfacial tension, the formulation for encapsulation was optimized for each individual VOC. Furthermore, to achieve effective stability of the large droplets/capsules, a combination of ionic and nonionic surfactants was used. Optical and scanning electron microscopy, Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA), were used to characterize the optimized microcapsules. The results showed that the obtained microcapsules exhibited a spherical shape and core–shell morphology and featured characteristic urethane-urea bonds. The amount of encapsulated VOC ranges between 54 and 7 wt %. The emission tests were performed with the help of the emission test chamber procedure (EN 16516). The limonene-loaded polyurethane/polyurea microcapsules show a change in emission rate of less than 10% within 14 days and can be considered as a potential candidate for use as an ERM. KW - Polymer microcapsules KW - Membrane emulsification KW - Polyaddition KW - Volatile organic compound (VOC) KW - Emission testing PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-619227 DO - https://doi.org/10.1021/acsami.4c12826 SN - 1944-8252 VL - 16 IS - 50 SP - 69999 EP - 70009 PB - ACS AN - OPUS4-61922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Misra, Archismita T1 - Polyoxometalate Ionic Liquids (POM-ILs) as Protective Coatings for CulturalHeritage against Acid Corrosion and Biodeterioration N2 - Corrosion of stone by acid rain anddeterioration from microbial biofilmsare challenges pertinent worldwide forindustrial or residential buildings as wellas cultural heritage artefacts, like statuesor historic buildings. One mitigationoption might be the use of thintransparent films of polyoxometalate-based ionic liquids (POM-ILs). In thisregard, different limestone samples werecoated with hydrophobic, acid resistantPOM-ILs which also have biocidalproperties.1 Exposure of the samples tosimulated acid rain showed negligiblecorrosion compared to the significantdeterioration of unprotected samples(Fig 1. Left). In addition, the biocidalproperties of the POM-ILs suppress theformation of biofilms on coated stoneslabs. The coating is mechanically stableand is not removed even by harshmechanical and chemical treatment.Following studies successfully exploredthe effectiveness of the coating againstlampenflora growing in the PommeryChampagne cellar 2 (Fig 1. Right); andthe long-term performance of POM-ILsunder outdoor environmental conditions3. So, POM-ILs are already proven topossess remarkable anticorrosion andantimicrobial properties against aerobicmicroorganisms and being water-insoluble, they don’t get leached intoaquatic ecosystem, which is extremelybeneficial from an environmentalsustainability and toxicological point ofview. The current project aims tocontinue the journey on protecting thecultural heritage, shifting focus fromstones to metals and employ functionalPOM-IL nanocoatings to prevent MIC(Microbiologically Influenced Corrosion)of cultural heritage artefacts made ofmetal or metal alloy like carbon steel,brass, cast iron or bronze. Performanceof both the coating materials and coatingtechniques via optimization of theadhesion of the nanocoating on themetallic surface on the corrosion rateand corrosion products in the MICcaused by anaerobic microorganismslike methanogenic archaea or SulphateReducing Bacteria (SRB) would betested. The objective is to establishPOM-ILs as efficient environmentallysustainable nanocoating materialsagainst biocorrosion citing the already published success stories; and sketch theongoing endeavours and prospects ofthese very efficient candidates in thecontext of MIC mitigation. T2 - Mitigation of Microbiologically InfluencedCorrosion: Towards Scientific &Industrial Standardization (MIC-STAND) CY - Lisbon, Portugal DA - 24.07.2024 KW - Microbiologically influenced corrosion (MIC) KW - Polyoxometalate Ionic Liquid KW - Nanocoating KW - Cultural heritage PY - 2024 AN - OPUS4-64575 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Misra, Archismita T1 - Polyoxometalate Ionic Liquids (POMILs) as Protective Coatings for Cultural Heritage Against Acid Corrosion and Biodeterioration N2 - Corrosion of stone by acid rain anddeterioration from microbial biofilms are challenges worldwide present forindustrial or residential buildings as wellas cultural heritage, like statues orhistoric buildings. One option is the useof thin transparent films ofpolyoxometalate-based ionic liquids(POM-ILs). Stone samples were coatedwith hydrophobic, acid resistant POM-ILs which also have biocidal properties.1Exposure of the samples to simulatedacid rain showed negligible corrosioncompared to the significant deteriorationof unprotected samples (Fig 1. Left). Inaddition, the biocidal properties of thePOM-ILs suppress the formation ofbiofilms on coated stone slabs. Thecoating is mechanically stable and is notremoved even by harsh mechanical andchemical treatment. Following studiessuccessfully explored the effectiveness ofthe coating against lampenflora growingin the Pommery Champagne cellar 2 (Fig1. Right); and the long-termperformance of POM-ILs under outdoorenvironmental conditions 3. So, POM-ILs are already proven to possessremarkable anticorrosion andantimicrobial properties against aerobicmicroorganisms and being water-insoluble, they don’t get leached intoaquatic ecosystem, which is extremelybeneficial from an environmentalsustainability and toxicological point ofview. The current project aims tocontinue the journey on protecting thecultural heritage, shifting focus fromstones to metals and employ functionalPOM-IL nanocoatings to prevent MIC(Microbiologically Influenced Corrosion)of cultural heritage artefacts made ofmetal or metal alloy like carbon steel,brass, cast iron or bronze. Performanceof both the coating materials and coatingtechniques via optimization of theadhesion of the nanocoating on themetallic surface on the corrosion rateand corrosion products in the MICcaused by anaerobic microorganismslike methanogenic archaea or SulphateReducing Bacteria (SRB) would betested. The objective would be toestablish POM-ILs as efficientenvironmentally sustainablenanocoating materials againstbiocorrosion citing the already publishedsuccess stories; and sketch the ongoingendeavours and prospects of these veryefficient candidates in the context ofbiocorrosion T2 - International Biodeterioration and Biodegradation Symposium CY - Berlin, Germany DA - 09.09.2024 KW - Microbiologically influenced corrosion (MIC) KW - Polyoxometalate Ionic Liquid KW - Nanocoating KW - Cultural heritage PY - 2024 AN - OPUS4-64576 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Misra, Archismita T1 - Polyoxometalate Ionic Liquids as Protective Coatings for Industrial Infrastructure and Cultural Heritage against Microbiologically Influenced Corrosion (MIC) N2 - Corrosion of stone and metal due to acid rain and biodeterioration poses significant challenges for industrial and residential infrastructure, as well as cultural heritage, including statues and historical artefacts. A promising mitigation strategy involves thin, transparent films of polyoxometalate-based ionic liquids (POM-ILs) as chemical shields. Stone samples coated with acid-resistant, biocidal POM-ILs exhibited negligible corrosion when exposed to simulated acid rain, in stark contrast to the severe deterioration of unprotected samples. Additionally, their biocidal properties effectively prevent biofilm formation on coated surfaces. Following studies successfully explored the effectiveness of the coating against lampenflora growing in the Pommery Champagne cellar; and the long-term performance of POM-ILs under outdoor environmental conditions. So, POM-ILs have already demonstrated remarkable anticorrosion and antimicrobial properties against aerobic microorganisms and, being water-insoluble, do not leach into aquatic ecosystem. The current research project repurposes the POM-ILs, extending their application to metals, specifically targeting microbiologically influenced corrosion (MIC) in cultural heritage artefacts made of brass, carbon steel, cast iron, and bronze. This involves optimizing nanocoating adhesion to the metal surface and evaluating its protective efficacy against MIC caused by anaerobic microorganisms such as methanogenic archaea and sulfate reducing bacteria (SRB). This presentation will highlight POM-ILs as sustainable, high-performance nanocoatings for biocorrosion mitigation. It will showcase published success stories, discuss ongoing research and proof-of-concept results, and explore future prospects for these advanced materials in safeguarding metal infrastructure and artefacts across different industrial sectors as well as in the context of cultural heritage conservation. T2 - 10th International symposium on applied microbiology and molecular biology in oil systems (ISMOS10) CY - Nashville, Tennessee, USA DA - 11.08.2025 KW - Polyoxometalates KW - Corrosion KW - Microbiologically Influenced Corrosion KW - Ionic Liquid PY - 2025 AN - OPUS4-64548 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Misra, Archismita T1 - Polyoxometalate Ionic Liquids as Protective Coatings for Industrial Infrastructure and Cultural Heritage against Microbiologically Influenced Corrosion (MIC) N2 - Corrosion of stone and metal due to acid rain and biodeterioration poses significant challenges for industrial and residential infrastructure, as well as cultural heritage, including statues and historical artefacts. A promising mitigation strategy involves thin, transparent films of polyoxometalate-based ionic liquids (POM-ILs) as chemical shields. Stone samples coated with acid-resistant, biocidal POM-ILs exhibited negligible corrosion when exposed to simulated acid rain, in stark contrast to the severe deterioration of unprotected samples. Additionally, their biocidal properties effectively prevent biofilm formation on coated surfaces. Following studies successfully explored the effectiveness of the coating against lampenflora growing in the Pommery Champagne cellar; and the long-term performance of POM-ILs under outdoor environmental conditions. So, POM-ILs have already demonstrated remarkable anticorrosion and antimicrobial properties against aerobic microorganisms and, being water-insoluble, do not leach into aquatic ecosystem. The current research project repurposes the POM-ILs, extending their application to metals, specifically targeting microbiologically influenced corrosion (MIC) in cultural heritage artefacts made of brass, carbon steel, cast iron, and bronze. This involves optimizing nanocoating adhesion to the metal surface and evaluating its protective efficacy against MIC caused by anaerobic microorganisms such as methanogenic archaea and sulfate reducing bacteria (SRB). This presentation will highlight POM-ILs as sustainable, high-performance nanocoatings for biocorrosion mitigation. It will showcase published success stories, discuss ongoing research and proof-of-concept results, and explore future prospects for these advanced materials in safeguarding metal infrastructure and artefacts across different industrial sectors as well as in the context of cultural heritage conservation. T2 - Euro-MIC COST Action - Closing Workshop Conference CY - Horsens, Denmark DA - 17.09.2025 KW - Polyoxometalates KW - Corrosion KW - Microbiologically Influenced Corrosion KW - Ionic Liquid PY - 2025 AN - OPUS4-64549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maltomini, F. A1 - Ghigo, T. A1 - Hahn, Oliver A1 - Rabin, Ira ED - Fournet, J.-L. ED - Kramer, B. ED - Luppe, W. ED - Maehler, H. ED - McGing, B. ED - Poethke, G. ED - Reiter, F. ED - Richter, S. T1 - Florentine papyri under examination: The material study of the inks used at the beginning of the Common Era in the "Family of Kôm Kâssûm" Archive (Hermopolis) N2 - Carbon inks with metallic admixtures are found on some papyri of the 2nd century CE from a family archive in Hermopolis. The great diversity of inks found in a single household within a short period of time suggests that inks were purchased rather than self-made. KW - Carbon ink KW - Iron-gall ink KW - Mixed ink KW - XRF ink analysis KW - Family archives KW - Hermopolis PY - 2021 DO - https://doi.org/10.1515/apf-2021-0010 SN - 0066-6459 SN - 1867-1551 VL - 67 IS - 1 SP - 146 EP - 165 PB - De Gruyter CY - Berlin AN - OPUS4-53160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Malefioudaki, Mariella A1 - Misra, Archismita A1 - Sbeity, Nadja A1 - Zueco-Vincelle, Juan A1 - Laguna-Bercero, Miguel A. A1 - Koerdt, Andrea A1 - Martín-Rapún, Rafael A1 - Mitchell, Scott G. T1 - Multifunctional polyoxomolybdate ionic liquid coatings for mitigating microbiologically influenced corrosion N2 - Corrosion of metals and other materials in marine environments poses significant economic, operational, safety, and environmental challenges across the oil and gas industry, the renewable energy sector, and maritime infrastructure. Microbiologically influenced corrosion (MIC) accounts for a substantial portion of this corrosion, with sulfate-reducing bacteria (SRB) and methanogenic archaea (MA) being key contributors. Conventional methods such as cathodic polarization have proven insufficient in mitigating the colonization of corrosive microbial communities in real marine environments, requiring the development of alternative, broad-spectrum antimicrobial strategies to prevent such biofilm formation. Recently, molybdate has emerged as a potential alternative to traditional biocides and nitrate. Our hypothesis is polyoxometalate-ionic liquids (POM-ILs), which exhibit antimicrobial and anticorrosion properties, could have a broader spectrum of antimicrobial activity than demonstrated until now and could be capable of shielding and protecting sensitive metal surfaces from the extreme acidic environments produced by MIC microorganisms. Here we show how two prototype polyoxomolybdate-based POM-ILs, [(CH3(CH2)6)4N]2[Mo6O19] and [(CH3(CH2)6)4N]4[Mo8O26], demonstrated antimicrobial activity at microgram per millilitre concentrations, prevented biofilm formation on metal surfaces, and provided resistance to corrosive acidic environments. Furthermore, impedance measurements were commensurate with electron microscopy studies showing that POM-IL-coated brass coupons withstood extremely corrosive environments. These proof-of-concept results demonstrate how multi-functional POM-IL coatings represent promising MIC mitigation solutions by providing a hydrophobic acid-resistant and biocidal protective layer that prevents biocolonisation and acidic corrosion by MIC microorganisms. KW - Polyoxometalates KW - Ionic liquid KW - Microbiologically influenced corrosion KW - Corrosion KW - Heritage preservation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631951 DO - https://doi.org/10.1039/d5mh00373c SN - 2051-6347 VL - 12 IS - 13 SP - 4648 EP - 4661 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-63195 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lange, Diana A1 - Hahn, Oliver ED - Lois, C. T1 - Colours on East Asian Maps N2 - Maps and colours have a close connection. Drawn or printed in black on white, subsequently added colours enhance maps with additional information. Colours were not just there to improve maps aesthetically, but they regulated how they were read and thus reinforced their meanings, significances and ideas. Colour is an important key to a more precise understanding of the map’s purposes and uses; moreover, colours are also an important aspect of a map’s materiality. The material scientific analysis makes it possible to find out more about the making of colours and the process of colouring maps. By skillfully deploying colours, map colourists were able to create mimetic representations of nature or codify information in an abstract form. The use of colours involved many considerations as to the materials. ‘Reading’ colours in this way gives a glimpse into the social lives of mapmakers as well as map users and reveals the complexity of the historical and social context in which maps were produced and how the maps were actually made. Within the scope of the three-year joint research project Coloured Maps (2018–2021), we undertook an in-depth and systematic study of hand-drawn and hand-coloured maps from East Asia in the Museum am Rothenbaum (MARKK) in Hamburg and produced between the seventeenth and twentieth centuries. With a multi-perspective approach and transdisciplinary methods (humanities and the sciences), we were able to pool and compare the research results from different fields of research on Asian maps. The aim of this publication is to provide a first general overview of the subject of colours on maps in East Asia in the period from the seventeenth to the early twentieth century and to stimulate further research on the topic. KW - Maps and colours KW - Colouring KW - Colourants KW - Dyes and pigments KW - Map production and publishing KW - Non-invasive scientific methods PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-569682 UR - https://brill.com/display/title/61839 SN - 978-90-04-54562-5 VL - 2023 SP - 1 EP - 79 PB - Brill CY - Leiden, Netherlands AN - OPUS4-56968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Diana A1 - Hahn, Oliver T1 - Colours on Maps - Purpose and Materiality N2 - Colours are an inseparable attribute of most maps. While colouring seems at first glance simply superficial ‘prettifying’ of maps, most maps were given colours for other reasons: colour is an important key to understanding the function and use of maps. The use of colours, the choice of where to assign them and the meaning given to them has accordingly never been static but has changed over time. In this context, the three aspects: colour system, colour scheme, and colour code are of particular importance. Material scientific analysis makes it possible to find out more about the material composition of colourants (pigments and dyes) on maps. The study of colourants provides insights into the production conditions and use of maps. Furthermore, it offers clues about colour changes and forms the basis for appropriate restoration concepts. T2 - Maps. Digital. Analogue CY - Oxford, United Kingdom of Great Britain and Northern Ireland DA - 26.02.2026 KW - Maps KW - Colours KW - Archaeometry KW - Aging PY - 2026 AN - OPUS4-65599 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Lange, D. A1 - Hahn, Oliver ED - Martin, E. ED - Brox, T. ED - Lange, D. T1 - Materials and materiality as keys to understanding a map of Mount Kailash N2 - While graphic and linguistic content is central to the identification of maps and can provide insights into the concepts and systems of rules, ideas and beliefs that led to their production, the materials that constitute maps may speak about manufacturing processes, the provenance of raw materials, the practical and technical knowledge of the mapmakers, and the use of the maps. This contribution underscores how the materials employed in Tibetan maps reveal aspects of their context and trajectory. Furthermore, materiality, conceptualized as a convergence of matter and imagination, can yield even more profound insights into artefacts like maps. Through a detailed case study of a map of Mount Kailash in the tangkha format and a specialized material-scientific analysis of the colourants employed in its creation, this contribution explores how a map can ‘talk’ through its materiality. With this case study it will show how Tibetan Studies can benefit from interdisciplinary collaboration. Crossing the field’s traditional boundaries and working with other disciplines, we argue, is absolutely essential for serious research. KW - Archaeometry KW - Non-destructive analysis KW - Cultural heritage PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-648625 SN - 978-3-98887-016-2 DO - https://doi.org/10.11588/hasp.1522 SP - 147 EP - 176 PB - Heidelberg Asian Studies Publishing (HASP) CY - Heidelberg AN - OPUS4-64862 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinge, A. T1 - upMIN 100 – upcycling of mineral construction and demolition waste to substitute natural aggregates in earthen building materials N2 - The construction sector is one of the most resource-intensive sectors in Germany and is responsible for 40 % of CO2 emissions. emissions. Around 517 million tons of mineral raw materials are required annually for the construction of buildings in Germany. At the same time, mineral construction waste was the largest material flow at 229.3 million tons (2020). The rates of building material recycling have increased since 2000, especially for mineral waste. Nevertheless, the majority of recycled aggregates are used in technically largely unregulated applications (e.g. road construction). This downcycling leads to a loss of valuable resources for technically and economically valuable uses. The upMIN100 research project is investigating the question of whether and to what extent recycled mineral construction and demolition waste is suitable as an additive in earthen building materials such as earth plasters and earth blocks. The focus is placed on grain sizes < 2 mm, which are currently predominantly landfilled, as there are currently no regulations for their use in building products. In order to enable the use of construction and demolition waste, the technical feasibility must be ensured, quality requirements for source materials (e.g. limit values for pollutants in terms of health and environmental environmental compatibility and hazardous substances) and permissible proportions of recycled aggregates must be defined. To avoid negative impact on building occupants, the developed building materials have been tested in terms of harmful substances included in the mineral waste as well as emissions into the ambient air. Furthermore, the earthen building products, manufactured from mineral waste, should be free from pollutants to enable a return into the environment. According to the Substitute Building Materials Ordinance (EBV) this corresponds to criterion BM-0. Two different building material developments were used to test the technical feasibility and the pollutant content of the recycled aggregate. T2 - Sustainable Built Environment Conference 2025 CY - Zurich, Switzerland DA - 25.06.2025 KW - Mineral waste KW - Upcycling KW - Earthen building product KW - Circular construction PY - 2025 AN - OPUS4-63552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Klinge, A A1 - Mönig, J A1 - Ziegert, C A1 - Richter, Matthias A1 - Kalbe, Ute A1 - Horn, Wolfgang A1 - Röhlen, U A1 - Rauscher, S A1 - Roswag-Klinge, E T1 - upMIN 100 – upcycling of mineral construction and demolition waste to substitute natural aggregates in earthen building materials N2 - The construction sector is one of the most resource-intensive sectors in Germany and is responsible for 40 % of CO2 emissions. Around 517 million tons of mineral raw materials are required annually for the construction of buildings in Germany. At the same time, mineral construction waste was the largest material flow at 229.3 million tons (2020). The rates of construction and demolition waste (CDW) recycling have increased since 2000, especially for mineral waste. Nevertheless, the majority of recycled aggregates are used in technically largely unregulated applications (e.g. road construction). This downcycling leads to a loss of valuable resources for technically and economically valuable applications. The upMIN 100 research project is investigating the question of whether and to what extent recycled CDW is suitable as an additive an binder in earthen building materials. The focus is placed on grain sizes of < 2 mm, which are currently predominantly landfilled, as there are at present no regulations for their use in building products. The soil matrix of earthen building materials however, naturally contains of different grain sizes, whith < 2mm – 0,063 for aggregates and < 0.063 mm as a binder. Therefore, the focused grain sizes (sand, clay and silt) could have a high usage potential. In order to enable the use of CDW, the technical feasibility must be ensured, quality requirements for source materials (e.g. threshold values for pollutants in terms of health and environmental compatibility and hazardous substances) and permissible proportions of recycled aggregates must be defined. Two different building material developments (earth blocks and -plaster)were used to assess both, the technical feasibility as well the pollutant content of the recycled aggregate and its final emissions into the indoor air. For both materials two mixtures could be established, that also meet the mechanical specifications according to the DIN standard, such as the compressive strength. A method was developed to design material mixtures with a high amount of CDW that comply with the defined limit values. The mixtures reached a recycling rate of 28 % with high mechanical properties and 70 % with minimum strength requirements. KW - Mineral waste KW - Upcycling KW - Earthen building product KW - Circular construction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652831 DO - https://doi.org/10.1088/1755-1315/1554/1/012084 SN - 1755-1307 VL - 1554 IS - 1 SP - 1 EP - 9 PB - IOP Publishing AN - OPUS4-65283 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klein, Luise T1 - Miniaturization Options in VOC Emissions Assessments of Consumer Products: Comparison of Test Chambers and Dynamic Headspace Extraction Systems N2 - Different emission testing devices were compared to measure reliable initial indoor air concen-trations of volatile organic compounds (VOC) emitting from consumer products. Compared to conventional medium- or large-scale test chambers, smaller devices including micro chambers and dynamic headspace extraction systems offer options for increased sample throughput, automation as well as reduced costs, which could facilitate their application in routine analysis of consumer product-related VOC emissions. T2 - Indoor Air 2024 CY - Honolulu, Hawaii, USA DA - 07.07.2024 KW - VOC KW - Emissions KW - Consumer product KW - Indoor air PY - 2024 AN - OPUS4-62098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ketelsen, T. A1 - Wintermann, Carsten A1 - Melzer, C. A1 - Dietz, Georg A1 - Golle, U. A1 - Hahn, Oliver ED - Cole, M. ED - Dogramaci, B. ED - Lehmann, A.-S. ED - Sölch, B. ED - Wedekind, G. T1 - Connoisseurship and the Investigation of Materiality: Four “Rembrandt” Drawings in Weimar N2 - The aim of this paper is to present the productive interplay of connoisseurship and material analysis when dealing with drawings by Rembrandt – or previously attributed to him – in the collection of the Klassik Stiftung Weimar. This concerns the more precise determination of the drawing materials used and the reconstruction of the genesis of the drawings discussed. The material analysis allows us to decide whether and how Rembrandt’s inks can be used to determine authorship at all. The “material turn” in drawing studies thus intervenes in the discussion about authorship and opens up a broader production aesthetic perspective. No longer the “style” but rather the handeling becomes the decisive criterion for answering the question “Rembrandt, or not?” KW - Archaeometry KW - History of Art KW - Drawings KW - Rembrandt PY - 2021 SN - 0044-2992 VL - 84 IS - 4 SP - 483 EP - 518 PB - Deutscher Kunstverlag CY - Berlin/München AN - OPUS4-54342 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ketelsen, T. A1 - Hahn, Oliver A1 - Golle, U. T1 - Blindness and Insight. The Rhetoric of Connoisseurship and the Investigation of Materiality. N2 - The aim of the lecture is to present the productive interplay of connoisseurs and material analysis using the example of selected drawings from the Rembrandt collection of the Klassik Stiftung Weimar. We try to determine the point at which the question of the materiality of the drawings makes sense in the traditional discourse of connoisseurship. On the one hand, this involves the question of authorship – Rembrandt – or not? – and the locating of attributed drawings in the context of the work. On the other hand, it is about making drawing processes visible, characterizing ways of drawing and workshop practices as well as distinguishing different forms of reworking and copying within the Rembrandt workshop. The material analyses culminate in the question of whether Rembrandt’s inks can be distinguished at all. It becomes apparent that the newly gained knowledge about the materiality of the drawing no longer reveals itself to the “mere” view of the connoisseur. Rather, it is only generated by the digital image. The rhetoric of connoisseurs must therefore be contrasted with the necessity of a hermeneutics of the digital image. The envisaged “material turn” of drawing science is thus simultaneously able to take up the critique of the question of authorship, which has been growing ever more recently, and to transfer it to a more comprehensive perspective of aesthetics of production. T2 - Drawings by Rembrandt. Connecting art history, science and conservation CY - Amsterdam, Rijksmuseum, The Netherlands DA - 06.02.2020 KW - Rembrandt KW - Drawings KW - Non-destructive testing KW - Inks KW - Paper PY - 2020 AN - OPUS4-50384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Richter, Matthias T1 - Round robin tests of odour and VOC emissions from building products – What have we learned so far? N2 - Emission testing of volatile organic compounds (VOC) and odour from materials and products is commonly based on emission test chamber measurements. These measurements are often the basis of mandatory or voluntary labelling procedures. To ensure the comparability of results from different testing laboratories their performance must be verified. For this purpose, round robin tests (RRTs) are conducted. Bundesanstalt für Materialforschung und - prüfung (BAM) offers such a RRT every two years using well characterised test materials with defined VOC emissions. In addition to the VOC quantification, the evaluation of odour is also implemented in the round robin tests. At the beginning, only perceived intensity (PI) was tested but over the years also the acceptance evaluation was considered. In principle, the results of PI and acceptance evaluation are comparable. The advantage of PI is the lower number of panel members necessary for one evaluation. T2 - Healthy Buildings 2023 Europe CY - Aachen, Germany DA - 11.06.2023 KW - Perceived intensity KW - VOC-emission KW - Poficiency test KW - Chamber test KW - Odour PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-580001 SP - 434 EP - 436 PB - ISIAQ (International Society of Indoor Air Quality and Climate) CY - Herndon, VA, USA AN - OPUS4-58000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Richter, Matthias A1 - Wilke, Olaf T1 - Volatile organic compounds from building products - Results from seven proficiency tests with emission test chambers conducted between 2008 and 2021 N2 - Emission testing of volatile organic compounds (VOC) from materials and products is commonly based on emission test chamber measurements. To ensure the comparability of results from different testing laboratories their measurement performance must be verified. For this purpose, Bundesanstalt für Materialforschung und -prüfung (BAM) organizes an international proficiency test every two years using well-characterised test materials (one sealant, one furniture board and four times a lacquer) with defined VOC emissions. The materials fulfilled the requirements of homogeneity, reproducibility, and stability. Altogether, 41 VOCs were included of which 37 gave test chamber air concentrations between 10 and 98 µg/m³. This is the typical concentration range to be expected and to be quantified when performing chamber tests. Four compounds had higher concentrations between 250 and 1105 µg/m³. The relative standard deviations (RSD) of BAM proficiency tests since 2008 are compared and the improvement of the comparability of the emission chamber testing is shown by the decrease of the mean RSD down to 23% in 2021. In contrast, the first large European interlaboratory comparison in 1999 showed a mean RSD of 51%. T2 - Proficiency Testing in Analytical Chemistry, Microbiology and Laboratory Medicine CY - Windsor, United Kingdom DA - 25.09.2023 KW - Proficiency Test KW - VOC-Emission KW - Chamber-test PY - 2023 AN - OPUS4-59694 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Müller, Birgit T1 - Low-odour and low-emission indoor products - Nose vers. odour threshold values N2 - To achieve good air quality in buildings, it is necessary to remove, avoid or reduce cleaning loads through ventilation. To reduce the cleaning loads and their effect on the odour perception of the occupants, a sensory test in indoor spaces and on building products is necessary in addition to VOC emission measurements of the contaminants. ISO 16000-28 provides the basis for odour assessment of products using a human olfactory panel. Through many years of experience and testing of these methods, it can now be assumed that reproducible odour ratings are available for many products used indoors. An odour measurement is mandatory for the Blue Angel for carpets and is being tested for environmentally friendly resilient floor coverings. Based on the results of an earlier project and new results of the upcoming study, the ISO should be revised and completed. The project investigates the odour and VOC emissions of building products based on natural raw materials. The data generated is used to address several issues, which are briefly explained below. Floor coverings based on linoleum and rubber are included in the Blue Angel eco-label with an odour assessment. The aim of the project is to clarify whether other assessment methods in addition to intensity can provide better information. Positive hedonics have an influence on the intensity assessment. Typically, building products show high intensity with low hedonic values. Results for wood-based products often show high intensity and positive hedonics. Based on these examples, an appropriate odour assessment of wood-based products for the Blue Angel, supported by research results, should be possible. The concept of the odour guide value which is based on odour threshold values was renewed in 2023. This approach will now be compared with the standardised odour measurement (16000-28). This assessment is based on GC/MS measurements and uses odour thresholds analytically when panel-based odour assessment is not possible. For this procedure well defined odour thresholds are necessary T2 - AIRMON 2025 The 11th International Symposium on Modern Principles of Air Monitoring and Biomonitoring. CY - Loen, Norway DA - 15.06.2025 KW - Emission KW - Indoor air quality KW - Materials emissions test KW - VOC KW - Geruch PY - 2025 UR - https://stami.no/en/wp-content/uploads/sites/2/2025/06/Programhefte-Airmon-2025-Juni-10-YTH.pdf AN - OPUS4-63634 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang A1 - Klein, Luise A1 - Bethke, Robert T1 - Determination of uptake rates of VVOCs and carbonyls in indoor air on passive sampling system N2 - The identity and concentration of volatile contaminants are important factors in ensuring a healthy indoor environment. Volatile organic compounds (VOCs) in indoor air can be determined by using passive samplers that are exposed to the air for a well-defined period of time. This sampling method is often used in environmental surveys, e.g. the German Environmental Survey (GerES). Conclusions about indoor air concentrations can be drawn from substance and adsorption material specific uptake rates. For the assessment of indoor air quality, highly volatile organic compounds may also be substantial, but for many of these substances realistic uptake rates and suitable analytical methods are lacking. A small chamber is used to generate gas atmospheres with constant concentrations of the analytes at 23 °C and 50 % relative humidity. For a large number of compounds, a very small flow of pure liquid VVOCs is introduced into the chamber via a syringe pump and mixed with a constant flow of clean and humidified air. A gas mixture from cylinders is also used for this purpose. Carbograph 5TD has already been proven as a suitable sorption material for active sampling for most of VVOCs. With this procedure up to 55 different VVOCs should be tested in this study. Stable concentrations of gas phase atmospheres of the first group of VVOCs (acetone, 2-butanone, methyl acrylate) were produced for exposure of passive samplers. Comparison of different adsorbent materials showed that Carbograph 5TD was the most suitable for passive sampling of these substances, with higher uptake than Carbopack X and Tenax® TA. Very strong adsorbents are not suitable for this experimental design as it adsorbs larger amounts of water. The effective uptake rates were calculated for the first three VVOCs on Carbograph 5TD tubes and an exposure time of 7 days. The same experiment will be performed for all VVOCs and ideally one material should be the best option for all of them. T2 - AIRMON 2025 The 11th International Symposium on Modern Principles of Air Monitoring and Biomonitoring. CY - Loen, Norway DA - 15.06.2025 KW - VVOC KW - Air quality KW - Passive sampling PY - 2025 UR - https://stami.no/en/wp-content/uploads/sites/2/2025/06/Programhefte-Airmon-2025-Juni-10-YTH.pdf AN - OPUS4-63632 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - VOC-Sampling inside display cases with focus on BEMMA evaluation N2 - Museum display cases aim to protect art and cultural goods not only from theft and vandalism, but also from dirt and dust. An often-heard argument within a call for tender of new display cases is that there should be no emission inside of the display case. This is nearly impossible for new ones especially when they must also fulfill the requirement of an air change rate of less than 0.1 per day. For example, constructions or decorations in exhibition spaces, storage containers in depot rooms, and exhibition display cases release volatile substances that might lead to irreversible changes or, under certain circumstances, damage to the stored or displayed objects. In Germany beneath the well-established Oddy-test also the BEMMA procedure is used to evaluate the construction materials. For larger amounts of display cases control measurements of VOCs at the end of construction or buildup is quite common. However, what is necessary to measure the air inside of display cases. What are the circumstances when the display cases were closed before the test period? Is it possible to organize a clean environment for reliable measurements. How comparable are the resulting VOCs with results from BEMMA test and control measurement at the end. The BEMMA procedure should include a further VOC-test at 60 °C. What are the benefits of this enlargement. Mainly materials that have a high potential to store VOCs inside of the material in combination with a less permeable surface should be evaluated stricter than others. T2 - IAQ 2024 The International Conference on Indoor Air Quality in Heritage and Historic Environments CY - New York, USA DA - 18.11.2024 KW - Emission KW - Air quality KW - Display cases KW - VOC PY - 2024 AN - OPUS4-61967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Horn, Wolfgang T1 - The BEMMA-Scheme helpful for low VOC inside display cases? N2 - Museums worldwide are equipped with different display cases. Exhibit display cases should protect cultural objects from dust as well as from mechanical and physical damage. To ensure a stable climate inside the display cases, a low air exchange rate is maintained. Typically, air exchange rates are often smaller than 0.1 d-1, which can result in rising concentrations of potential harmful VOC inside of the display cases due to emissions from materials. Especially organic acids, e. g. formic or acetic acid which can emit from e.g. sealing materials or wood-based materials, can produce damage of cultural objects. In 2012 BAM introduced a procedure which is called: BEMMA-Scheme (Bewertung von Emissionen aus Materialien für Museums¬ausstattungen) which stands for: “Assessment of Emissions from Materials for Museum Equipment”. Regarding the testing procedure only construction materials were evaluated, not the display cases their self. Micro chambers are used for VOC emission tests of display case construction materials, e.g. plastics, sealing materials, coatings, textiles and others. Each sampling procedure is carried out in duplicate. Emissions like formic acid, acetic acid, formaldehyde, piperidine-derivates and oximes are excluded and the sum of emissions of VVOCs, VOCs and SVOCs is limited. For a positive assessment all listed criteria must be fulfilled; otherwise the display construction material fails the BEMMA scheme. T2 - Indoor Air Quality in Heritage and Historic Environments CY - Online meeting DA - 12.10.2020 KW - Museum KW - VOC-emission KW - BEMMA KW - Display case PY - 2020 AN - OPUS4-51470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Helman-Wasny, Agnieszka ED - Martin, E. ED - Brox, T. ED - Lange, D. T1 - What makes ‘Tibetan paper’ Tibetan? Understanding the materiality of Tibetan paper N2 - Paper, as a writing support, is an integral element of the materiality of Tibetan books together with the technologies of their production. Analysis of the material features of the paper used in Tibetan written artefacts can help us to unravel their provenance, which is often unknown. First, however, we need a relatively clear understanding of the characteristic features of paper produced within particular book cultures and geographical regions at particular periods of time. This chapter offers a starting point by discussing the general characteristics of paper that originated in Tibet. Drawing on macro- and microscopic studies, it highlights the wide variety of paper types that have been used as writing supports in Tibetan written artefacts, before examining in more detail the raw materials, papermaking technologies and processes, and writing surface preparations that might justify the descriptor ‘Tibetan’ and thus grant Tibetan identity to paper. KW - Written artefacts KW - Paper KW - Tibet PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-649288 SN - 978-3-98887-016-2 DO - https://doi.org/10.11588/hasp.1522 SP - 113 EP - 146 PB - Heidelberg Asian Studies Publishing (HASP) CY - Heidelberg AN - OPUS4-64928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver A1 - Nöller, Renate ED - Dora, C. ED - Fabian, C. ED - Knoche, M. ED - Linder, M. ED - Mittler, E. ED - Schmitz, W. T1 - Writing inks in the Manuscripta Americana – a pilot study N2 - The manuscripts – which have been inventoried as Manuscripta Americana in the State Library of Berlin and the Biblioteka Jagellońska in Krakow with the signatures Ms. Americ. 1-15 – are codices mainly from the colonial times of the 16th to 18th centuries. They uniquely reflect the relationships between indigenous culture and Spanish colonial masters. This study focusses on the scientific investigation of three manuscripts (Manuscripta Americana 3, 8, and 10) that are kept today in Krakow. It is assumed that these three parts belong together in a certain way, so various material analyses were carried out to prove this assumption. The scientific investigation focusses on the different black and brown writing inks. T2 - Manuscripta Americana: Aufarbeitung einer Sammlung CY - Ibero-Amerikanisches-Institut, SPK DA - 14.02.2019 KW - Humboldt Codices KW - Writing inks KW - Non-destructive testing PY - 2020 SN - 978-3-447-11511-7 SN - 0067-8236 VL - 53 SP - 21 EP - 32 PB - Harrassowitz Verlag CY - Wiesbaden AN - OPUS4-51935 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Hahn, Oliver A1 - Nehring, G. A1 - Freisitzer, R. A1 - Rabin, Ira T1 - A study on early european inks from St. Paul in lavanttal N2 - Typology of Inks Archives and museums around the world contain a vast number of manuscripts that were written in different inks: carbon inks, plant inks, iron-gall inks and mixed inks. Yet most archaeometric studies of manuscripts focus on the palette of pigments found in illuminated manuscripts whereas identification of the inks is still largely based on cultural-historical studies and visual inspections. One of the reasons of this disproportion in the studies can be explained by the properties of Raman spectroscopy, the technique of choice for identification of pigments. In contrast, this technique is only partially viable when dealing with organic colourants. Brown and Clark discuss these difficulties and the uncertainties of identification of iron-gall inks by Raman spectroscopy in their pioneering work on early medieval Anglo-Saxon manuscripts (K. Brown and R. Clark 2004). To facilitate instrumental analysis of inks, we have developed a protocol that starts with the identification of the inks type (Rabin et al. 2012) which doesn’t require complicated instrumentation and can be carried out by paleographers and codicologists. Three typological ink classes The black writing materials used in manuscript production in Antiquity und Middle Ages can be sorted in three typologically different ink classes: soot, plant and iron-gall. Soot ink is a fine dispersion of carbon pigments in a water soluble binding agent; plant-based ink consists of a solution of the tannins extracted from gallnuts or tree bark; iron-gall ink, is produced by mixing a soluble compound of iron (II) with gallic or tannic acid extracted from gallnuts or tree bark. Therefore, iron-gall ink presents a boundary case between solution and dispersion ink, in which a water-soluble preliminary stage oxidizes and evolves into a black, insoluble precipitate similar to the carbon pigments when the writing is exposed to air (Krekel 1999). The additional category of mixed inks, i.e. inks produced by addition of various metals to the soot inks or intentional mixing of iron-gall and soot - based inks started attracting scholarly attention only recently because their significance was established only a short while ago (Brun et al. 2016, Colini 2018, Nehring et al. 2021). We suggest that plant and mixed inks build a bridge from the carbon ink of Antiquity to the properly formulated iron-gall ink that became a standard black ink from the late Middle Ages to the 19th century when it gave way to modern inks. KW - Early european inks KW - Typology of Inks KW - Raman spectroscopy KW - Illuminated manuscripts KW - Archaeometric studies KW - Dispersion of carbon pigments PY - 2021 VL - 2021 SP - 56 EP - 75 PB - Gazette du livre médiéval CY - Paris AN - OPUS4-53844 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Hahn, Oliver A1 - Golle, U. A1 - Wintermann, Carsten A1 - Laurenza, D. ED - Quenzer, J. B. T1 - Scientific Analysis of Leonardo’s Manuscript with Anatomic Drawings and Notes N2 - In this paper, we discuss the importance of scientifically investigating cultural artefacts in a non-invasive way. Taking as test case Leonardo da Vinci’s Manuscript with anatomic drawings and notes, which is stored in Weimar, we clarify fundamental steps in the chronology of this folio. By means of microscopy, infrared reflectography, UV photography, and X-ray fluorescence analysis, we were able to identify various types of sketching material and several varieties of iron gall ink. For his sketches, Leonardo used two different sketching tools, a lead pencil and a graphite pencil, as well as several types of ink for developing these sketches into drawings. With regard to ink, it is important to observe that there is no difference between the ink Leonardo used for drawing and the ink he used for writing text. Based on the materials analysed, we suggest a chronology for the creation of this unique folio. KW - Archaeometry KW - Non-invasive analysis KW - Drawings KW - Leonardo da Vinci PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543460 SN - 978-3-11-074545-0 DO - https://doi.org/10.1515/9783110753301-011 VL - 25 SP - 213 EP - 228 PB - Walter de Gruyter GmbH CY - Berlin/Boston AN - OPUS4-54346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Oliver T1 - More than 25 years of ink analysis non-destructive testing of black writing materials N2 - Writing inks can be divided into soluble inks and dispersion inks. Soluble inks are based on plant or insect dyes forming a water solution. In the early European Middle Ages brown plant inks were usually produced from the blackthorn bark and wine. In contrast to these soluble brown inks, one of the oldest black writing materials was produced by mixing soot with gum arabic or animal glue dissolved in a small amount of water. From Pliny’s detailed account of the manufacture of various black carbon inks, we learn that producing pure soot of high quality was not an easy task in Antiquity. Iron gall inks are a borderline case between these two groups. They are produced from four basic ingredients: gallic acid, an iron-containing component, gum arabic as a binding media, and an aqueous medium such as wine, beer, or vinegar. By mixing gallic acid with soluble iron ions, a water-soluble ferrous gallate complex is formed. Exposure to oxygen leads to the formation of insoluble black ferric gallate pigment. Due to the variety of recipes and the natural origin of raw materials, there is a wide range of different components and impurities in writing inks. The Bundesanstalt für Materialforschung und -prüfung (BAM) together with the Centre for the Study of Manuscript Cultures in Hamburg (CSMC) has developed a protocol for ink analysis. It consists of a primary screening to determine the type of the ink and a subsequent in-depth analysis using several spectroscopic techniques (X-ray fluorescence analysis and vibrational spectroscopy). This contribution presents a qualitative and quantitative analysis of historical writing inks to characterize distinguishable inks in manuscripts, to determine the origin of manuscripts, and to assign unknown fragments to time and place. T2 - Beyond the reconstruction of an Urtext: “About the history of the early Qurʾānic text with regard to digital research tools” CY - Hesse, Germany DA - 07.07.2025 KW - Archaeometry KW - Non-destructive testing KW - Material analysis KW - Cultural heritage PY - 2025 AN - OPUS4-63906 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grzelec, Małgorzata A1 - Haas, Sylvio A1 - Helman-Ważny, Agnieszka T1 - Application of scanning small-angle X-ray scattering in the identification of sheet formation techniques in historical papers N2 - Among writing substrates produced historically in different regions of the world, paper is one of the most complex materials. Its complexity results not only from a variety of highly processed ingredients, which can be used in its production, but also from a variety of methods in which these materials are combined to form the fibrillar network referred to as paper. While material identification methods are well established in the analysis of historical papers, the identification of manufacturing technologies is still an under-researched topic, that requires the development of appropriate methods and measurement protocols. This paper reports on the results of a research project aimed at the application of synchrotron scanning small angle X-ray scattering (SAXS) method in the characterization of paper structure, with emphasis on the assessment of fibrillar orientation as a marker characteristic for different, historical papermaking technologies. The main objective of this study consists of the development of a measurement protocol involving the SAXS technique complemented by other analytical methods in the characterization of the fibrous paper structure. KW - SAXS KW - Paper analysis KW - Papermaking technology KW - Fiber orientation PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-651594 DO - https://doi.org/10.1007/s00339-024-08157-4 SN - 0947-8396 VL - 131 IS - 1 SP - 1 EP - 16 PB - Springer Science and Business Media LLC AN - OPUS4-65159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gruskovà, J. A1 - Martin, G. A1 - Kresten, O. A1 - Mitthoff, F. A1 - Kaska, K. A1 - Hofmann, C. A1 - Kreuzer, W. A1 - Phelps, M. A1 - Boydston, K. A1 - Easton Jr., R. L. A1 - Knox, K. T. A1 - Kelbe, D. A1 - Kasotakis, D. A1 - Christens-Barry, W. A. A1 - Stewart, D. A1 - Rabin, Ira A1 - Hahn, Oliver A1 - Glaser, L. A1 - Garrevoet, J. A1 - Shevchuk, I. A1 - Klumpp, S. A1 - Deckers, D. A1 - Buck, J. ED - Cronier, M. ED - Mondrain, B. T1 - Insights-into-the-Digital-Recovery-of-the-Scythica-Vindobonesia N2 - The Scythica Vindobonensia, the new fragments on Gothic incursions into Roman provinces in the Balkans in the middle of the third century AD that were revealed some years ago in a Greek palimpsest at the Austrian National Library in Vienna (ÖNB), are commonly considered as one of the most important additions of the last decades to the corpus of texts from classical Antiquity. Tere is a high degree of confdence among scholars in supposing that the fragments come from the lost work Scythica written in Greek by the third-century historian P. Herennius Dexippus (Δέξιππος) of Athens. The new fragments have hence also been called Dexippus Vindobonensis. In his Scythica, Dexippus recorded wars of the Romans with the Goths (and other tribes) whom he called Scythians. The work had been hitherto known only from excerpts and quotes by later authors. Eight pages of a Byzantine manuscript copy of the ancient text have survived hidden underneath the visible surface of the last four parchment folios of the Vienna manuscript Historicus graecus 73, f. 192r -195v4. The copy is written in a Greek calligraphic minuscule which has been estimated by palaeographers to be of the middle or the second half of the eleventh century. In the thirteenth century, the text (on each of the eight pages arranged in one column, with 30 lines per page) was washed of the parchment and the valuable material made from animal skin was re-used for Christian texts. The new writing largely covered the faded remnants of the original text. It thus became hidden from the human eye for more than seven hundred years. Its discovery by Jana Grusková, a classical philologist specialized in the transmission of Greek texts, resulted from a systematic review of all Greek palimpsests kept at the Austrian National Library in Vienna at the beginning of the twenty-first century and a detailed examination of the four folios in 2007-20097. KW - Scythica Vindobonensia, KW - Gothic incursions KW - A Greek palimpsest KW - Antiquity KW - Byzantine manuscript KW - Vienna manuscript PY - 2020 SN - 978-2-916716-81-7 SN - 0577-1471 VL - 2020 IS - 24/1 SP - 945 EP - 967 PB - Association des Amis du Centre d’Histoire et Civilisation de Byzance CY - Paris ET - 1 AN - OPUS4-53843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grimmer, Christoph A1 - Richter, Matthias A1 - Neuhaus, T. A1 - Prinz, Carsten A1 - Strzelczyk, Rebecca Skadi A1 - Colakoglu, Irem A1 - Horn, Wolfgang T1 - Towards a multi-VOC emission reference material with temporally constant emission profile for QA/QC of materials emission testing procedures N2 - Emission reference materials (ERMs) are sought after to further control and improve indoor air quality. The impregnation of porous materials with volatile organic compounds (VOCs) is a promising approach to produce ERMs. Different VOCs were used to impregnate various porous materials (mainly zeolites, activated carbons and a metal organic framework). The influence of different methodological parameters and material properties were studied to optimize the impregnation procedure and to find the best material/VOC combination. The impregnation procedure remains quite irreproducible, nevertheless, very good ERM candidates were identified. Two materials (zeolite 4 and AC 1 impregnated with n-hexadecane) showed a very stable emission over 14 days (<10 % change). Another material (AC 1 impregnated with toluene) showed a declining emission profile but with a very good in-batch reproducibility and a storage stability of up to 12 months. KW - Emission reference material KW - Porous materials KW - Indoor air quality KW - Emission test chamber KW - CO2 assisted impregnation KW - EN 16516 PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612238 DO - https://doi.org/10.1016/j.chemosphere.2024.143437 SN - 1879-1298 VL - 366 SP - 1 EP - 8 PB - Elsevier AN - OPUS4-61223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimmer, Christoph T1 - Development, application and measurement uncertainty of emission reference materials N2 - Volatile organic compounds (VOCs) emitted by furniture and building materials can cause health issues. For an improvement of indoor air quality low emitting materials should be used. Quality assurance and –control (QA/QC) measures require an emission reference material (ERM) with a predictable emission rate of VOCs. The idea is to use porous materials as ERM, which store the VOCs inside their pores and emit them constantly. T2 - Webinar Metrology for Indoor Air Quality Reference materials for QA/QC of the emission test chamber procedure CY - Online meeting DA - 11.04.2024 KW - Emission reference materials KW - Indoor air quality KW - Materials emissions test KW - VOC PY - 2024 AN - OPUS4-59963 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grimmer, Christoph T1 - Preparation of novel emission reference materials: μ-capsules & impregnated porous materials N2 - Volatile organic compounds (VOCs) emitted by furniture and building materials can cause health issues. For an improvement of indoor air quality low emitting materials should be used. Quality assurance and –control (QA/QC) measures require an emission reference material (ERM) with a predictable emission rate of VOCs. The idea is to use porous materials as ERM, which store the VOCs inside their pores and emit them constantly. T2 - WORKSHOP: METROLOGY FOR INDOOR AIR QUALITY CY - Mol, Belgium DA - 18.10.2023 KW - Emission reference materials KW - Indoor air quality KW - Materials emissions test KW - VOC PY - 2023 AN - OPUS4-59961 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gordon, Nehemia A1 - Patrick, Andrist A1 - Hahn, Oliver A1 - Vasileiadis, Pavlos D. A1 - Calvillo, Nelson A1 - Rabin, Ira T1 - Did the Original Scribes Write the Distigmai in Codex Vaticanus B of the Bible (Vat. gr. 1209)? N2 - The fourth-century Greek Bible manuscript Codex Vaticanus B (Vat. gr. 1209) contains pairs of horizontally aligned marginal dots known as distigmai, which correspond to textual variants in other manuscripts. The production of the distigmai has been variously dated to the 4th or 16th centuries. A fourth-century date would prove the early existence of hundreds of textual variants, many of which are otherwise only witnessed by later manuscripts. Near infrared microscope reflectography combined with micro-X-ray fluorescence spectroscopy proved that the distigmai, both those categorized as “apricot” (which are visually similar to the ink of the original main text) and “chocolate” (which are visually similar to the reinking of the main text) were written with ink(s) made from chemically purified vitriol, a process that only became standard in the 16th century. As a result, there is no reasonable chance that the distigmai were written in the fourth century. Horizontal lines that have been hypothesized to function as text-critical obeloi were written in the same ink as the original main text, which differs completely from that of the distigmai. In other words, the distigmai and horizontal lines tested were not produced during the same writing session and are separated by more than 1,000 years, making it impossible for them to have functioned as conjoining text-critical symbols in the 4th century. KW - Bible manuscripts KW - New Testament KW - Paratextual features KW - Textual criticism KW - Obelos KW - Septuagint KW - XRF KW - Greek palaeography PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-622902 DO - https://doi.org/10.1163/27728641-00302005 SN - 2772-8633 VL - 3 IS - 2 SP - 125 EP - 156 PB - Brill CY - Leiden AN - OPUS4-62290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gordon, N. A1 - Bonnerot, Olivier A1 - Rabin, Ira ED - Friedrich, M. ED - Quenzer, J. T1 - Inks Used to Write the Divine Name in a Thirteenth-Century Ashkenazic Torah Scroll: Erfurt 7 (Staatsbibliothek zu Berlin, Ms. or. fol. 1216) N2 - The scribe of ‘Erfurt 7’, a thirteenth-century Torah scroll now kept in Berlin, initially left blank spaces for the divine appellations Elohim ( אלהים ) and YHWH Elohim ( ,(יהוה אלהים which were filled in during a second stage of writing. The appearance of the ink employed to write the appellations was significantly darker than that of the surrounding ink. X-ray fluorescence analysis (XRF) has shown that the light and dark brown inks had similar elemental compositions, but contained different ratios of iron to potassium, which could be explained by the use of different batches of ink. According to some medieval sources, the divine appellations were sometimes filled in during a second stage of writing in the presence of ten men from the Jewish community. In Erfurt 7, the two-stage procedure was only performed in the first 1.5 columns of the original sheets, suggesting it may have been part of a public ceremony inaugurating the writing of the divine names in the scroll. Erfurt 7 emerges from this study not only as a ritual object used for liturgy, but as a rallying point for the Jews of Erfurt to come together as a community to express their reverence for the written form of God’s name. The divine name YHWH ( יהוה ) was written in a smaller script than the surrounding text on three replacement sheets using the same two-stage procedure. The ink used on the replacement sheets contained zinc, which is characteristic of other Erfurt manuscripts as well. This suggests that Erfurt was the place where the scroll was used, cherished and eventually repaired. KW - Torah KW - Ink KW - Erfurt KW - 13th century PY - 2020 SN - 1867–9617 VL - 15 SP - 163 EP - 184 AN - OPUS4-52965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Glaser, L. A1 - Shevchuk, I. A1 - Tolkiehn, M. A1 - Rabin, Ira A1 - Hahn, Oliver T1 - Improving Iron Gall Ink Palimpsest X-ray Fluorescence Element Mapping Analysis N2 - In the recent years multispectral imaging and X-ray Fluorescence element mapping have established themselves as a well working two step approach, when dealing with faded, erased or overwritten text in iron gall ink. During the last years a lot was done to improve the mere technical side of the techniques. Especially in the case of XRF mapping experiments the acquisition speed needed to be increased to allow mapping in the high resolution demanded by the challenges at hand. High resolution in moderate times can now be achieved, but with the price of proportionally increased amount of data that needs to be processed ideally in parallel to the measurement. The classical approach in XRF spectroscopy of elemental fitting of the spectral data does not even come close to fulfill any on the fly processing time constraints and will consume too much processing time in the foreseeable future. In this paper we will discuss the applicability of modern statistical data processing methods to XRF mapping of iron gall ink palimpsests. We will present a comparison of a new approach based on principle and independent component analysis (PCA and ICA) and the standard element mapping method. We will show that a reduction in processing time of almost two orders of magnitude can easily be achieved. T2 - Kongress Visual Heritage, CHNT 23 CY - Vienna, Austria DA - 15.11.2018 KW - Palimpsest KW - Iron-gall ink PY - 2020 SP - 1.1 EP - 1.9 AN - OPUS4-50243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ghigo, Tea A1 - Torallas, S. T1 - Between Literary and Documentary Practices: The Montserrat Codex Miscellaneus (Inv. Nos. 126‐178, 292, 338) and the Material Investigation of Its Inks N2 - The Montserrat Codex Miscellaneus (TM 59453/LDAB 552) has been the subject of numerous studies since the publication of ist first text by its owner, father Ramon Roca-Puig. Scholars have dealt with the content of its texts, as well as interrogated its origin and materiality. It is a fourth-century papyrus single quire codex, which contains texts in both Latin and Greek. It has been argued that it belonged to the Bodmer library, connected to a Pachomian library in the Thebaid. In this paper we want to contribute to the material study of the codex by presenting the first results of an archaeometric analysis performed upon the inks. The Analysis was carried out within the framework of the ‘PAThs’ project based at Sapienza University of Rome, and executed with the close cooperation of DVCTVS, a team of scholars who curate the Roca-Puig collection. The results obtained have not only cast light on the history of production of the codex, but also, and perhaps most importantly, point out that a meaningful interpretation of the analytical data is only possible through an interdisciplinary collaboration between the humanities and the natural sciences. KW - Interdisciplinary approach KW - Codex Miscellaneus KW - Palaeography KW - Book production KW - Archaeometry KW - Ink analysis PY - 2020 SP - 101 EP - 114 AN - OPUS4-51004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, P. T1 - Black Egyptian inks in Late Antiquity: new insights on their manufacture and use N2 - We present here our methodological approach applied to the study of Egyptian inks in Late Antiquity. It is based on an interdisciplinary strategy, bringing together a variety of disciplines from humanities and natural sciences, and it aims at systematically collecting a statistically relevant amount of data regarding the composition of the inks. The application of a wellestablished, non-invasive protocol that includes near-infrared imaging and X-ray fluorescence spectroscopy for in situ measurements enables the identification and characterisation of inks dating from the end of Late Antiquity onwards. However, sometimes this method limits our understanding when characterising more ancient inks. Trying to overcome these limitations, the potential of a new device for the characterisation of organic compounds is here explored by conducting preliminary tests on mock samples. In this work, we present the results from 77 codicological units that include some of the earliest manuscripts of our corpus that presently lists 159 units. KW - Ink KW - Archaeometry KW - Manuscripts KW - Coptic KW - Egypt PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-503893 DO - https://doi.org/10.1007/s12520-019-00977-3 VL - 12 IS - 3 SP - 1 EP - 14 PB - Springer AN - OPUS4-50389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ghigo, Tea A1 - Rabin, Ira T1 - Gaining Perspective into the Materiality of Manuscripts: The Contribution of Archaeometry to the Study of the Inks of the White Monastery Codices N2 - An interdisciplinary approach to the study of manuscript traditions is here applied to the analysis of the leaves from the White Monastery, one of the greatest centres of literary production in Late Antique Egypt. In the framework of the ‘PAThs’ project, archaeometric analyses complement the information pieced together by a range of disciplines in the field of humanities. The use of different complementary analytical techniques provides information on the type of ink used and its elemental composition, unveiling interesting details regarding the materials and methodology of manufacturing of writing media. Moreover, this contribution takes a step forward and discusses the possible existence of a regional arrangement in the elemental composition revealed in the inks studied. KW - Manuscript making KW - Archaeometry KW - Ink analysis KW - Interdisciplinary approach KW - Coptic studies PY - 2020 SP - 273 EP - 282 AN - OPUS4-51003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Even, Morgane A1 - Juritsch, Elevtheria A1 - Richter, Matthias T1 - On the use of Carbograph 5TD as an adsorbent for sampling VVOCs: validation of an analytical method N2 - A standardised method for the analysis of very volatile organic compounds (VVOCs) in indoor air is still missing. This study evaluates the use of Carbograph 5TD as an adsorbent for 60 compounds (47 VVOCs + 13 VOCs) by comparing their recoveries with different spiking modes. The influence of the spiking of the tubes in dry nitrogen, humidified air or along the whole flushing duration mimicking real sampling was investigated. 49 substances (36 VVOCs from C1 to C6) had recoveries over 70% on the adsorbent in humidified air and were validated. The linearity of the calibration curves was verified for every spiking mode and the limits of detection (LOD) and quantification (LOQ) were determined. The LOQs were lower than the existing indoor air guideline values. The robustness of the method was considered by studying the influence of the sampling volume, the sampling flow rate, the humidity level and the storage of the tubes. In general, the most volatile or polar substances were the less robust ones. The combined measurement uncertainty was calculated and lies below 35% for a vast majority of the substances. An example of an emission chamber test using polyurethane foam is shown: Carbograph 5TD performs much better than Tenax® TA for VVOCs and emissions from n-butane were quantified with combined measurement uncertainty. KW - VVOC KW - Gas chromatography KW - Thermal desorption KW - Air sampling PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-581113 DO - https://doi.org/10.1039/D3AY00677H VL - 15 IS - 31 SP - 3810 EP - 3821 AN - OPUS4-58111 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - BOOK A1 - Dietz, G. A1 - Eggert, Claudia A1 - Golle, U. A1 - Hahn, Oliver A1 - Ketelsen, T. A1 - Ludwig, A. A1 - Melzer, C. A1 - Rabin, Ira A1 - Wintermann, C. ED - Hahn, Oliver ED - Doil, Thorsten ED - Wintermann, C. T1 - The materiality of drawings - A scientific approach N2 - Volume 5 of the N.i.Ke. series presents the current state of materials science and imaging techniques used in the examination of drawings. The first part of the publication introduces the classic drawing substrates and materials. The middle part of the publication describes the relevant materials science and imaging techniques. The final part discusses the possibilities and limitations of these methods using several case studies. KW - Archaeometry KW - Paper KW - Parchment KW - Drawing materials KW - Drawings KW - Nondestructive testing PY - 2024 SN - 2567-1251 N1 - Es gibt eine parallele Sprachausgabe (deutsch), ein Link befindet sich im Feld zugehöriger Identifikator - There is a parallel language edition (German), a link is in the field related identifier VL - 5 SP - VII EP - 110 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-63672 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Desvergnes, Amélie Couvrat A1 - Helman-Wazny, Agnieszka T1 - Sialkoti paper used by Pahari artists: Raw materials and fibre analysis N2 - This study aims to characterise the so-called Sialkoti paper used to produce Pahari drawings preserved today in the Wereldmuseum in Leiden (Netherlands) (WML). These works originate from the Punjab Hills in India (today Himachal Pradesh) and are commonly known as ‘Pahari miniature paintings’. The paper upon which these drawings are executed is said to have been produced in Sialkot during the eighteenth and nineteenth centuries when papermaking was an integral part of an overall regional economy correlated with other sectors such as agriculture and the textile industry. Although the term Sialkoti refers to identified papermills in Sialkot (now Pakistan), the paper from this region is yet to be subjected to a systematic study. This article therefore explores the paper(s) in question through macro- and microscopic observations of structure, pulp and fibres. The study of historical sources, complemented by the analysis of paper samples and fibre identification, has revealed that the pulp would have been prepared from a variety of manufactured products using different technologies, such as rags, cloth, mats, rope and other plant-based materials made from local bast fibres which, once tattered, were recycled to prepare the pulp. Microscopic study reveals that a variety of fibre combinations under different conditions and processing steps were used, in particular sunn hemp fibre (Crotalaria juncea L.), a plant species that has until now rarely been identified in historical paper. In addition, the presence of kenaf and jute fibres, as well as a significant quantity of cotton fibres, have also been demonstrated. To overcome the lack of comparative materials, our work was supported by a comparative study of several materials made from sunn hemp now held in the Ethnobotany Collection at Kew Gardens. Samples were taken from these materials and provided useful reference micrographs for the identification of the WML samples. The quality of the paper used by Pahari artists, as well as the raw materials available and their processing, are discussed in detail. Putting all the data, including technical and historical information into perspective, we conclude that the Pahari artists used a paper of inferior quality compared to other types of paper used for other purposes such as the creation of illuminated manuscripts in the Punjab plains. This study therefore provides useful analytical and material evidence that complements previous historical, technical and anthropological studies. KW - Sialkoti paper KW - Pahari drawings KW - Indian handmade paper KW - Sunn hemp KW - Fibre identification KW - Microscopy PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-645216 DO - https://doi.org/10.1186/s40494-024-01360-9 SN - 2050-7445 VL - 12 SP - 1 EP - 18 PB - Springer CY - Cham AN - OPUS4-64521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - de Krom, I. A1 - Heikens, D. A1 - Horn, Wolfgang A1 - Wilke, Olaf A1 - Richter, Matthias A1 - Baldan, A. T1 - Metrological generation of SI-traceable gas-phase standards and reference materials for (semi-) volatile organic compounds N2 - EN 16516 sets specifications for the determination of emissions into indoor air from construction products. Reliable, accurate and International System of Unit (SI)-traceable measurement results of the emissions are the key to consumer protection. Such measurement results can be obtained by using metrologically traceable reference materials. Gas-phase standards of volatile organic compounds (VOCs) in air can be prepared by a variety of dynamic methods according to the ISO 6145 series. However, these methods are not always applicable for semi-VOCs (SVOCs) due to their high boiling point and low vapour pressure. Therefore, a novel dynamic gas mixture generation system has been developed. With this system gas-phase standards with trace level VOCs and SVOCs in air can be prepared between 10 nmol mol−1 and 1000 nmol mol−1. The VOCs and SVOCs in this study have normal boiling points ranging from 146 °C to 343 °C. Metrologically traceable reference materials of the gas-phase standard were obtained by sampling of the VOC gas-phase standard into Tenax TA® sorbent material in SilcoNert® coated stainless steel tubes. Accurately known masses between 10 ng and 1000 ng per VOC were sampled. These reference materials were used to validate the dynamic system. Furthermore, the storage and stability periods of the VOCs in the reference materials were determined as these are crucial characteristics to obtain accurate and SI-traceable reference materials. In a round robin test (RRT), the reference materials were used with the aim of demonstrating the feasibility of providing SI-traceable standard reference values for SVOCs for interlaboratory comparison purposes. Based on the results from the validation, the storage and stability studies and the RRT, gas-phase standards and reference materials of VOCs and SVOCs with relative expanded uncertainties between 5% and 12% (k = 2) have been developed. These reference standards can be used as calibrants, reference materials or quality control materials for the analysis of VOC emissions. KW - SVOC KW - Dynamic calibration gas mixtures KW - Reference materials KW - Indoor air KW - Thermal desorption PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-565978 DO - https://doi.org/10.1088/1361-6501/aca704 VL - 34 IS - 3 SP - 1 EP - 13 PB - IOP Publishing AN - OPUS4-56597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Davenport, Rebecca T1 - Regulations versus practice and the Divine Name: Ink analysis in medieval Torah scrolls N2 - The medieval Rabbis had very strict rules for the construction of a Sefer Torah. The Divine Names should be written • by a qualified scribe • who is ritually pure • in the presence of a minyan (10 adult Jewish men) • in an appropriate frame of mind • without being interrupted However, when these scrolls were written it would have been impossible to verify any of this after the fact. While we do not currently have any way to determine how recently the scribes had bathed, or what they might have been thinking as they wrote, we can now know much more about the inscription of the Divine Name than these scribes ever would have guessed. It is sometimes apparent from a visual inspection of the text that the Divine Name has been written in a second stage, from irregular letter kerning or a different ink colour. Using XRF, we have been able to discover more instances of a different ink used for the Name, and have shown that in some cases the secondary ink was also used to correct the main text, suggesting that the later writing was done by a master scribe who also proofread the entire scroll. Using a Brucker M6 Jetstream, it has been possible to produce elemental “heat maps” of whole paragraphs or even large sections of a parchment sheet. Using such large samples of text, we can usefully compare the levels of copper and zinc used to write individual letters or words despite their relatively low concentration, which permits very fine differentiation of the inks used. The techniques presented here would also be highly applicable to assessing ink degradation, as they are able to detect much smaller differences in ink composition than had previously been possible. T2 - The International Iron Gall Ink Meeting 2025 CY - Lisboa, Portugal DA - 07.05.2025 KW - XRF spectroscopy KW - Torah scrolls KW - Jewish studies KW - XRF mapping PY - 2025 AN - OPUS4-65036 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Colini, Claudia A1 - Shevchuk, I. A1 - Huskin, K. A. A1 - Rabin, Ira A1 - Hahn, Oliver ED - Quenzer, J. B. T1 - A New Standard Protocol for Identification of Writing Media N2 - Our standard protocol for the characterisation of writing materials within advanced manuscript studies has been successfully used to investigate manuscripts written with a pure ink on a homogeneous writing surface. However, this protocol is inadequate for analysing documents penned in mixed inks. We present here the advantages and limitations of the improved version of the protocol, which now includes imaging further into the infrared region (1100−1700 nm). KW - Archaeometry KW - Manuscripts KW - Non-destructive testing PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-543454 SN - 978-3-11-074545-0 DO - https://doi.org/10.1515/9783110753301-009 VL - 25 SP - 161 EP - 182 PB - Walter de Gruyter GmbH CY - Berlin/Boston AN - OPUS4-54345 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Colini, Claudia ED - Michel, C. ED - Friedrich, M. T1 - La invencíon del Sacromonte: How and Why Scholars Debated about the Lead Books of Granada for Two Hundred Years N2 - At the end of the sixteenth century, a number of relics and artefacts were discovered in Granada, Spain. They included what became known as the Lead Books of the Sacromonte, twenty-one written artefacts made of circular lead leaves engraved in archaic Arabic characters. The authorship was attributed to some Arab disciples of St James the Greater considered to be the first evangelisers of the Iberian Peninsula. The texts, the materiality and the circumstances of the discoveries fuelled a debate surrounding their authenticity that lasted more than two centuries, a debate so fierce and controversial that not even papal condemnation in 1682 was able to stop it. Soon after the discoveries were made public, scholars highlighted the many contradictions and errors of a historical, linguistic and theological nature present in the texts, identifying members of the local Morisco community as possible forgers. This article focuses on how the scholarly community of the sixteenth and seventeenth centuries handled these findings and looks at the methods employed by the scholars to evaluate the authenticity of the artefacts. It will also look at how the particular interests of the various authorities involved influenced the acceptance or dismissal of relevant academic results. KW - Forgery KW - Moriscos KW - Parchment KW - Lead books PY - 2020 UR - https://www.degruyter.com/view/title/590832 DO - https://doi.org/10.1515/9783110714333-011 VL - Studies in Manuscript Cultures 20 SP - 209 EP - 262 PB - De Gruyter CY - Berlin/Boston AN - OPUS4-51936 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cohen, Zina A1 - Hahn, Oliver A1 - Rabin, Ira A1 - Ward, Aengus T1 - Centenary Paper: Of Inks and Scribes: The Composition of a Thirteenth-Century Castilian Manuscript – British Library Res 20787 N2 - This article presents the results of the first scientific analysis of the inks of a thirteenth-century Castilian manuscript – British Library Res 20787, a copy of the Fuero de las leyes. The analysis reveals the fingerprint of the inks used in the codex and points the way to future cross-disciplinary research based on a wider corpus of evidence. KW - Archaeometry KW - Manuscript KW - Colorant KW - Cinnabar PY - 2024 DO - https://doi.org/10.3828/bhs.2024.56 SN - 1475-3839 VL - 101 SP - 703 EP - 720 PB - Liverpool University Press AN - OPUS4-61435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cohen, Zina A1 - Hahn, Oliver A1 - Rabin, Ira ED - Lattuati-Derieux, Agnès ED - Ribeyrol, Charlotte ED - Heginbotham, Arlen T1 - Black Carolingian inks under examination. Part 1: recipes and literature survey N2 - Black writing materials of different types and compositions have varied in use over time and different geographical regions. With this paper, we would like to contribute to their study by listing and reviewing recipes for black writing inks that were in circulation in the Carolingian Empire as well as by referencing the archaeometric analyses of the black inks used in the manuscripts. The studies presented here that involved the humanities and natural sciences provide new insights into how the scholars of the early Medieval Ages organized manuscripts. N2 - L’emploi des differents types de materiaux d’ecriture noirs et leurs compositions ont varie selon les epoques et les regions. Nous souhaitons ici contribuer a leur etude en repertoriant et en analysant les recettes d’encres de calligraphie noires en circulation dans l’Empire carolingien, ainsi qu’en procedant au referencement des analyses archeometriques des encres noires utilisees dans les manuscrits. Faisant appel aux sciences humaines et aux sciences naturelles, ces analyses apportent un eclairage nouveau sur la maniere dont les savants du haut Moyen Age organisaient les manuscrits. KW - Ink KW - Manuscript KW - Middle Ages KW - Recipes KW - Ink analyses KW - Carolingian PY - 2023 SN - 1254-7867 VL - 2023 IS - 55 SP - 90 EP - 95 PB - Centre de Recherche et de Restauration des Musées de France CY - Paris AN - OPUS4-58839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - BOOK A1 - Cohen, Zina T1 - Composition Analysis of Writing Materials in Cairo Genizah Documents N2 - Through the application of scientific methods of analysis to a corpus of medieval manuscripts found in the Cairo Genizah, this work aims to gain a better understanding of the writing materials used by Jewish communities at that time, shedding new light not only on the production of manuscripts in the Middle Ages, but also on the life of those Jewish communities. KW - Ink analyses KW - Cairo Genizah KW - X-Ray fluorescence analyses KW - Reflectography KW - Middle Ages PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-588642 UR - https://brill.com/display/title/59331 SN - 978-90-04-44887-2 SN - 978-90-04-46935-8 SP - 1 EP - 192 PB - Brill CY - Leiden & Boston AN - OPUS4-58864 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina T1 - Beyond the text: What writing materials of the Cairo Genizah tell us N2 - Results: - Four types of inks were measured iron gall (vitriolic and non vitriolic), carbonic, mixed and vegetable inks. - We need to start analyzing systematically the organic part of the inks. - Great variety in the composition of the inks. - No correlation between the type of ink used and any other criteria apart from a personal preference. - Inks purchased by (some) scribes. - Reconstruction of the chronology of writing and signing of certain legal documents. - Comparison with documents written by the Muslim court. T2 - Ink Workshop CY - Munich, Germany DA - 28.06.2022 KW - Ink analyses KW - Manuscript studies KW - X-Ray fluorescence analyses KW - Cairo Genizah KW - Middle Ages PY - 2022 UR - https://www.naher-osten.uni-muenchen.de/wasistlosaminstitut/veranstaltungsarchiv/veranstaltungen-2022/inkworkshop/index.html AN - OPUS4-58874 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cohen, Zina T1 - Material Studies of Torah Scrolls at the Bundesanstalt für Materialforschung und -Prüfung N2 - In recent years the BAM has been focusing on the characterization of the writing materials of the medieval Torah scrolls. The challenge imposed by the study of this specific type of manuscript led to designing and building dedicated stages to ensure the safety of the scrolls during the analysis. Furthermore, the identification of multiple corrections executed in apparently identical inks required broadening the standard two-step protocol of near infrared reflectography and X-ray fluorescence to include multispectral imaging. This work has prepared the division to participate in the large collaborative project “To roll: Materialisierte Heiligkeit (Materialised Holiness)” based at the Free University, Berlin. The presentation will demonstrate the aims of the studies, preliminary results and the strategies adopted by the division 4.5 of the BAM. T2 - EAJS Congress Branching Out: Diversity of Jewish Studies CY - Frankfurt/Main, Germany DA - 16.07.2023 KW - Ink analyses KW - Manuscript studies KW - Torah Scrolls KW - X-Ray fluorescence KW - Middle Ages PY - 2023 AN - OPUS4-58881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cohen, Z. A1 - Hennings, T. A1 - Hahn, Oliver A1 - Depreux, P. A1 - Rabin, Ira T1 - Black inks under examination. Part 2: a case study of Carolingian manuscripts N2 - With this paper, we would like to contribute to the study of black writing materials by investigating the black inks used in the manuscripts from monastic production in the eastern part of the Frankish kingdom, especially in the region of Lake Constance and in Bavaria and dated to the period between the 8th and the 10th centuries. The corpus under study contains manuscripts with formulae, i.e. model letters and charters, besides numerous other types of texts with no clear separation between them (for example by titles). Sixty-three manuscripts have been studied with the aim of reconstructing the history of both their copying and their use. To this aim, we adopted a non-invasive approach that included near-infrared imaging and X-ray fluorescence spectroscopy for on-site measurements, supported by historical and palaeographic analysis. The results obtained in this project are compared with several other archaeometric studies of contemporary manuscripts with the general aim of understanding the use of black ink in medieval manuscripts. KW - Manuscript KW - Ink analysis KW - Carolingian PY - 2023 DO - https://doi.org/10.4000/techne.18919 SN - 2239-0243 VL - 56 SP - 105 EP - 113 AN - OPUS4-61582 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandt, S. A1 - Brozowski, F. A1 - Horn, Wolfgang A1 - Müller, B. T1 - Odour testing of building products: Examinations for an on-going development of the test standard ISO 16000-28 N2 - VOC-emissions and their odours from building products and furnishings present indoors should not have an impact on personal well-being or health. Odours can be measured by applying the standard ISO 16000-28. Indoor air determination of odour emissions from building products using test chambers. One of the described procedures is the assessment of perceived intensity using a comparative scale by a group of panellists. In this paper, the perceived intensity sampling procedure and its evaluation method are investigated and shown to need improvement. New technical developments in the methodology used to increase the reproducibility of measurement results are discussed. Since odour tests are used for labelling, they have a major influence on the assessment of construction products, similar to the procedure of the German Committee for Health Evaluation of Building Products (AgBB). In the original ISO standard, the evaluation is typically performed using a sampling container separated from the emission chamber. For a better sample presentation, an adapter was developed to connect the emission test chamber to the evaluation funnel and thus enable an odour assessment which is comparable to a direct measurement. The investigations show that losses of odourous substances can be greatly reduced, which is very desirable when seeking to obtain reliable results in odour measurement. Another experimental series was carried out to reduce the measurement effort in the evaluation of perceived intensity. Application of the developed greater than or less than/equal to. query could be helpful here. The results show that the query mostly leads to the same result as the evaluation of the perceived intensity using the method according to the standard but is much easier to perform. Overall, the results can contribute to improving the acceptance of the evaluation of perceived intensity using ISO 16000-28 and to determining odours from building materials increasingly more precisely. T2 - Healthy Buildings 2023 Europe CY - Aachen, Germany DA - 11.06.2023 KW - Building material KW - Odour KW - Perceived intensity KW - VOC KW - Emission test chamber PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-580070 SP - 345 EP - 352 PB - ISIAQ (International Society of Indoor Air Quality and Climate) CY - Herndon, VA, USA AN - OPUS4-58007 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -