TY - CONF A1 - Wilke, Olaf T1 - Contaminants of Emerging Concern from Materials and Products: Measurement and Evaluation N2 - Test chamber measurements are an important tool to improve indoor air quality and occupational safety. Test chamber measurements are possible for a wide range of materials, products and technologies. Determination of concerning contaminants is important to ensure good indoor air quality. The detection of concerning contaminants depends on the approriate sampling and analysis. T2 - Webinar BAM-University of Birmingham CY - Online meeting DA - 24.02.2021 KW - Emerging Contaminants KW - Emission Test Chamber KW - Thermal Extraction KW - Thermal Desorption PY - 2021 AN - OPUS4-52262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Harmonised test standard EN 16516 - common approach for all building products for interiors N2 - The presentation gives general information about the European Standard EN 16516 “Construction products – Assessment of release of dangerous substances – Determination of emissions into indoor air”. This test standard was developed based on the mandate M/366 of the European commission and is a horizontal reference method for the determination of volatile organic compounds (VOC) from different classes of construction (building) products. Specific test conditions are to be selected by the product TCs (technical committees) in a way that a product is tested under its intended condition of use. The test is based on the use of emission test chambers which are operated at constant air change rate and climate (23°C, 50 % r.h.) over 28 days. The standard defines the conditions and requirements for the measurement including loading factor, air change rate, sampling, analysis and calculation of emission rates of the substances. A 30 m³ reference room is described which is used to calculate air concentrations from the determined emission rates. The standard EN 16516 enables the evaluation of construction products regarding their emissions into indoor air under defined and comparable conditions. The evaluation includes the determination of identified target compounds, non-identified target compounds, volatile carcinogenic compounds and the sum values TVOC, TSVOC and R. T2 - UBA Conference - Limiting health impacts of construction products regarding VOC CY - Online meeting DA - 20.04.2021 KW - Building products KW - EN 16516 KW - Emisson testing KW - Construction products PY - 2021 AN - OPUS4-58079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wen, Keqing T1 - In situ analysis of biofilm formation under different flow regimes with the help of a microfluidic platform N2 - Bacteria often live in habitats characterized by fluid flow, which is ubiquitous in a diverse range of environments such as surface waters, wastewater treatment facilities, pipelines, and medical implants. Bacterial adhesion on surfaces may lead to biocorrosion and biodegradation. In comparison to traditional static and macro flow chamber assays for biofilm formation studies, microfluidic chips allow in situ monitoring of biofilm formation and biofilm related gene expression under various flow regimes. We developed a complete microfluidic platform to investigate biofilms under precisely controlled flow conditions. This platform central unit is a single-inlet microfluidic flow cell with a 5 mm wide chamber tested and analyzed by imaging tracking velocimetry (PIV) to achieve ultra-homogenous flow in the central area of the chamber. Additionally, dedicated microstructures were introduced to the chamber’s center to favor and localize bacterial adhesion and biofilm formation pattern. The flows and vortices induced by the structure were analyzed by computational fluid dynamics (CFD) and related to shape and dimension of the biofilm formed by Escherichia coli TG1. The major proteinaceous component of E. coli biofilms are extracellular amyloid fibers (curli) consisting of major (CsgA) and minor (CsgB) subunits. We used the promotor probe plasmid pRU1701 to monitor csgB-promotor activity under different flow regimes in complex and minimal medium. For comparison, csgB promotor activity in a batch liquid culture and curli production on LB and M9 agar plates were assessed. The microfluidic platform represents a powerful and versatile tool for studying biofilm in flow. The setup shows great potential for the yet not too much explored in flow monitoring of biofilm formation and related gene expression under hydrodynamic stresses. T2 - International Biodeterioration and Biodegradation Symposium (IBBS) 19 CY - Berlin, Germany DA - 09.09.2024 KW - Microfluidics KW - Biofilm KW - Escherichia coli KW - Curli PY - 2024 AN - OPUS4-61911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Einführung in die Mantelverordnung - Stand der Bundes-Bodenschutz- und Altlastenverordnung N2 - Einführung in die Mantelverordnung Stand der Bundes-Bodenschutz- und Altlastenverordnung, aktuelles zum Aufbau der MVO und zum Stand Anfang 2023 T2 - X. Baustoffseminar - Aktuelles zu Gesteinskörnungen CY - Bad Berka, Germany DA - 17.01.2023 KW - Mantelverordnung KW - Gesteinskörnungen KW - Wiederverwertung PY - 2023 AN - OPUS4-57798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Entwicklungen im Gipsrecycling N2 - Gips gehört zu den nachgefragtesten Baustoffen und entsprechend steigt der Gipsverbrauch weltweit schon seit Jahrzehnten an. In Deutschland wird der Gipsbedarf seit vielen Jahren zu einem guten Teil durch REA-Gips, einem Nebenprodukt aus der Abgasreinigung von Kohlekraftwerken, gedeckt. Die weitere Gipsversorgung erfolgt größtenteils durch die Nutzung natürlicher Gipsvorkommen. Ein geringer, aber steigender Anteil an RC-Gips aus dem Baustoffrecycling und die Nutzung synthetischer Gipse aus Nebenprodukten anderer Industriezweige sind ebenfalls zu verzeichnen. Aufgrund der nationalen Klimaschutzziele und der damit verbundenen Abschaltung von Kohlekraftwerken wird das REA-Gipsangebot in den nächsten Jahren jedoch weiter deutlich zurückgehen, so dass andere Gipsquellen erschlossen werden müssen. Abhängig von der Lebensdauer der verwendeten Gipsprodukte im Bausektor ist infolge des in den vergangenen Jahren erfolgten Anstiegs des Gipsverbrauchs auch mit einer Zunahme von Gipsresten in Bau- und Abbruchabfällen zu rechnen. Im Hinblick auf eine bevorstehende Verknappung von Gips wird die Rückgewinnung dieser Gipse aus Bau- und Abbruchabfällen immer wichtiger. Das Recycling von Gipskartonplatten ist mittlerweile eine etablierte Technik und wird bereits seit einigen Jahren in industriellem Maßstab durchgeführt. Außerdem werden neue Verfahren zur Wiederverwertung weiterer Gipsprodukte aus Rück- und Umbaumaßnahmen untersucht. Von besonderem Interesse sind verschiedene Arten von Gipsplatten, da sie gut für selektiven Rückbau geeignet sind. Daher können sie vergleichsweise frei von Verunreinigungen oder Störstoffen zurückgewonnen werden, was für das Gipsrecycling besonders wichtig ist. In dem vom Bundesministerium für Bildung und Forschung geförderten Forschungsprojekt "GipsRec 2.0" werden technische, wirtschaftliche und ökologische Aspekte des Recyclings von Gipsfaserplatten sowie von verschiedenen Synthesegipsen untersucht und bewertet. Die Aufbereitung von Gipsfaserplatten erfolgte im halbtechnischen Maßstab, an verschiedenen potentiellen Ausgangsstoffen für synthetische Gipse wurden Laborversuche durchgeführt. Erfolgversprechende Verfahrenswege werden ökobilanziell bewertet. Ziel dieser Arbeiten ist die Erschließung der Sekundärrohstoffpotenziale von weiteren Quellen für die RC-Gipsproduktion um mit einer Steigerung des Gipsrecyclings die in naher Zukunft durch die Reduktion der REA-Gips-Bereitstellung entstehende Lücke in der Rohstoffversorgung zu verringern. T2 - 21. ibausil 2023 CY - Weimar, Germany DA - 13.09.2023 KW - Baustoffrecycling KW - Sekundärgipse KW - Ökobilanz PY - 2023 AN - OPUS4-60314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Neue Ansätze beim Gipsrecycling N2 - Gypsum is widely used in the construction sector, and its worldwide consumption has been increasing now for several decades. Currently, the gypsum demand is met up to 60% by FGD gypsum (a by-product from coal-fired power plants) in Germany. The natural gypsum deposits cover the remaining gypsum demand. Due to national climate protection goals and the related shutdown of coal-fired power plants, the FGD gypsum supply will decrease significantly in the coming years and, therefore, other gypsum sources must be found. Depending on the lifetime of the used gypsum products in the construction sector, an increase of gypsum in construction and demolition waste is to be expected. With regard to an upcoming shortage of gypsum, several approaches are being tested to recover gypsum from construction and demolition waste. Gypsum plasterboard recycling is already implemented on an industrial scale. Furthermore, new processes to recycle different types of gypsum products from construction and demolition waste are being examined. Of particular interest are different types of gypsum boards because they are well suited for selective dismantling. Therefore, they can be recovered comparatively free of impurities which is most important for the gypsum recycling. In the research project “GipsRec 2.0”, funded by the Federal Ministry of Education and Research, recycling methods for gypsum fiberboards are being investigated. Additionally, the suitability of different types of synthetic gypsum as substitutes for FGD gypsum is being considered. Currently, the quantities of recycled gypsum are not sufficient with regard to the reduction of FGD gypsum. An increase of gypsum recycling should be achieved to narrow the future gypsum gap that will occur in the near future. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 13.09.2021 KW - Gipsabfälle KW - Gipsrecycling KW - Nachhaltigkeit PY - 2021 AN - OPUS4-53682 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Baustoffrecycling: Kreislaufwirtschaft und Umweltschutz N2 - Aktuelle Zahlen zum Baustoffrecycling Zielkonflikte im Kontext von Abfallwirtschaft, Boden- und Grundwasserschutz sowie rechtlichen Vorgabe mit den Beispielen rezyklierte Gesteinskörnungen und RC-Gips. T2 - IX. Baustoffseminar CY - Weimar, Germany DA - 11.03.2020 KW - Kreislaufwirtschaft KW - Baustoffrecycling KW - Ressourcenschonung PY - 2020 AN - OPUS4-51436 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - New sources for secondary gypsum N2 - In order to protect natural gypsum deposits and to compensate for the decreasing amount of Flue Gas Desulfurization (FGD) gypsum it is necessary to develop and explore new sources of gypsum. For this purpose, the potentials of different gypsum wastes are investigated in the study “GipsRec 2.0”, funded by the Federal Ministry of Education and Research (Germany). On the one hand, the project worked on a new processing technology for gypsum fiberboards (GFB). While the recycling of gypsum plasterboards has already been carried out on an industrial scale for several years, the recycling of gypsum fiberboards (GFB) has proven to be challenging. Gypsum fiberboards from demolition sites and offcuts from GFB production were used for these investigations. The tests were conducted on a technical scale. Furthermore, various synthetic gypsums are being investigated with regard to their suitability for gypsum production. The analyses are carried out on production residues. In this project, a promising process for gypsum fiberboard recycling could be developed, as well as other waste gypsums are investigated and evaluated with regard to their potential as secondary raw material. In addition, selected process routes are assessed for their environmental impact using a life cycle assessment (LCA) approach. T2 - RILEM - V International Conference Progress of Recycling in the Built Environment CY - Weimar, Germany DA - 10.10.2023 KW - Gypsum recycling KW - Gypsum fiberboards and synthetic gypsum KW - Environmental evaluation PY - 2023 AN - OPUS4-60316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Biofilme auf Gebäuden - Biorezeptivität statt Biofilme N2 - Der Vortrag erläutert das Konzept der Gebäudebegrünung mit Biofilmen. Beton wird dabei als künstliches Gestein betrachtet, dessen Besiedelbarkeit durch Mikroorganismen gezielt verbessert werden soll. Ein dreistufiges Testsystem – Laborversuche, simulierte Bewitterung und Freilandtests – analysiert, wie physikalische und chemische Substrateigenschaften das Wachstum beeinflussen. Ein definierter Algen‑Pilz‑Modellbiofilm dient zur reproduzierbaren Bewertung der Besiedlung, erfasst über PAM‑Fluorometrie. Die Ergebnisse zeigen, dass Rauheit, Textur und Porosität entscheidend für Anhaftung, Feuchteretention und Biofilmwachstum sind. Zudem wird deutlich, dass die Organismen hohe Stresstoleranz benötigen, um variierende Umweltbedingungen an realen Fassaden zu überstehen. Insgesamt belegt das Projekt das Potenzial biorezeptiver Betone als low‑tech‑Fassadenbegrünung mit ökologischem Mehrwert. T2 - Workshop Ökologische Campusentwicklung: Wasser und Vegetationsmanagement in Helmholtz-Zentren CY - Potsdam, Germany DA - 03.04.2025 KW - Biofilm KW - Fassade KW - Biorezeptivität KW - Low-tech Begrünung KW - Modellbiofilm PY - 2025 AN - OPUS4-65448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia T1 - Bioreceptive Building Facades: Codesigning with nature N2 - Building envelopes represent a key interface between solid substrates, the biosphere, and the atmosphere, and consequently serve as natural habitats for subaerial biofilms. This study investigates strategies to enhance the bioreceptivity of concrete cladding to support microalgae‑rich biofilms as a sustainable alternative to biocide‑dependent facade systems. Using a controlled dual‑species biofilm model and assessing algal vitality via PAM fluorometry, we examined how concrete composition and surface properties influence colonization dynamics. The results demonstrate that substrate pH and carbonation state are primary determinants of both biofilm establishment and organismal vitality, whereas nutrient supplementation exerts comparatively minor effects. Adhesion assays indicate that moderate mechanical stress can increase biofilm robustness, and laboratory rain simulations show that surface texture and near‑surface porosity promote water retention and enhance biofilm attachment. A synergistic interaction between the algal and fungal components was observed under specific stress conditions, offering a potential explanation for the reduced performance of biofilms when transitioning from ideal laboratory settings to outdoor environments. Overall, the findings highlight that the development of stable, photosynthetically active biofilm facades requires careful optimization of organism growth, physiological performance, and long‑term adhesion to the substrate. T2 - SASBE 2025: Smart and Sustainable Built Environment CY - Lille, France DA - 03.11.2025 KW - Concrete KW - Bioreceptivity KW - Laboratory test KW - Biofilm KW - Fluorometry PY - 2025 AN - OPUS4-65446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -