TY - CONF A1 - Even, Morgane A1 - Juritsch, Elevtheria A1 - Jann, Oliver A1 - Richter, Matthias T1 - Towards an efficient procedure for the analysis of VVOC emissions N2 - This poster summarizes the points that need to be addressed towards the standardization of an efficient procedure for the analysis of VVOC emissions: Standard mixture generation and investigations on mutual reactivity, selection of an appropriate sorbent combination, water management and choice of a suited GC column. T2 - Indoor Air 2020: The 16th conference of the international society of indoor air quality and climate CY - Online meeting DA - 01.11.2020 KW - VVOCs KW - Analytical method KW - ISO 16000-6 KW - EN 16516 PY - 2020 AN - OPUS4-52023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Even, Morgane A1 - Wilke, Olaf A1 - Kalus, Sabine A1 - Schultes, P. A1 - Hutzler, C. A1 - Luch, A. T1 - Formaldehyde emissions from wooden toys: Method comparison and exposure assessment N2 - This study shows that formaldehyde Emission results in micro-scale emission chambers are comparable with results in bigger chambers both for particle boards and wooden toys. On the contrary, the WKI flask method was leading to more variable results depending on sample geometry. Thus, microchambers could be used for reliable routine market surveillance. An exposure assessment led to noticeable formaldehyde indoor air concentration values, pointing out the need for an effective Surveillance of such samples. T2 - Indoor Air 2020: The 16th conference of the international society of indoor air quality and climate CY - Online meeting DA - 01.11.2020 KW - Volatile organic compounds KW - Consumer products KW - WKI flask method KW - Emission chambers KW - Market surveillance PY - 2020 AN - OPUS4-52024 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Even, Morgane A1 - Hutzler, C. A1 - Wilke, Olaf A1 - Luch, A. T1 - Emissions of volatile organic compounds from polymer-based consumer products: comparison of three emission chamber sizes N2 - The ISO 16000 standard series provide guidelines for emission measurements of volatile organic compounds (VOCs) from building materials. However, polymer-based consumer products such as toys may also release harmful substances into indoor air. In such cases, the existing standard procedures are unsuitable for official control laboratories due to high costs for large emission testing chambers. This paper aims at developing and comparing alternative and more competitive methods for the emission testing of consumer products. The influence of the emission chamber size was investigated as smaller chambers are more suited to the common size of consumer products and may help to reduce the costs of testing. Comparison of the performance of a 203 l emission test chamber with two smaller chambers with the capacity of 24 l and 44 ml, respectively, was carried out by using a polyurethane reference material spiked with 14 VOCs during the course of 28 days. The area-specific emission rates obtained in the small chambers were always similar to those of the 203 l reference chamber after a few hours. This implies that smaller chambers can provide at least useful numbers on the extent of polymer-based consumer product emissions into indoor air, thereby supporting meaningful exposure assessments. KW - Comparison KW - Consumer products KW - Emission chamber KW - Reference material KW - Volatile organic compounds PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-493697 DO - https://doi.org/10.1111/ina.12605 VL - 30 IS - 1 SP - 40 EP - 48 PB - Wiley VCH-Verlag AN - OPUS4-49369 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gehrenkemper, Lennart A1 - Simon, Fabian A1 - Roesch, Philipp A1 - Fischer, Emily A1 - von der Au, Marcus A1 - Pfeifer, Jens A1 - Cossmer, Antje A1 - Wittwer, Philipp A1 - Vogel, Christian A1 - Simon, Franz-Georg A1 - Meermann, Björn T1 - Organically bound fluorine in river water - A methode comparison of CIC and HR-CS-GFMAS N2 - Abstract: Since it is unknown for many applications, which PFASs are used and how they enter the environment, target analysis-based methods reach their limits. The two most frequently used sum parameters are the adsorbable organically bound fluorine (AOF) and the extractable organically bound fluorine (EOF). Both can be quantified using either combustion ion chromatography (CIC) or high resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS). Here we provide an insight on the advantageous and disadvantageous of both sum parameters and both detection methods. Our study is based on the analysis of surface water samples. Next to total fluorine (TF) analysis, AOF and EOF were determined as well as CIC and HR-CS-GFMAS are compared and results are comparatively discussed. Fluorine mass balancing revealed that, the AOF/TF proportion was higher than the EOF/TF proportion. The AOF made up 0.14–0.81% of TF and the EOF 0.04–0.28% of TF. Although, organically bound fluorine represents only a small portion of TF, PFASs are of worldwide concern, because of their extreme persistence and their bioaccumulation potential. The EOF-HR-CS-GFMAS method turned out to be more precise and sensitive than the AOF-CIC method and is a promising tool for future monitoring studies/routine analysis of PFASs in the environment. T2 - SALSA Make and Measure 2020: Advanced Characterization of Materials CY - Online meeting DA - 15.10.2020 KW - High resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS) KW - Combustion ion chromatography (CIC) KW - Per- and polyfluorinated alkyl substances (PFASs) KW - Adsorbable organically bound fluorine (AOF) KW - Extractable organically bound fluorine (EOF) KW - Surfacewaters PY - 2020 AN - OPUS4-52451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gehrenkemper, Lennart A1 - Simon, Fabian A1 - Roesch, Philipp A1 - Fischer, E. A1 - von der Au, Marcus A1 - Pfeifer, Jens A1 - Cossmer, Antje A1 - Wittwer, Philipp A1 - Vogel, Christian A1 - Simon, Franz-Georg A1 - Meermann, Björn T1 - Determination of organically bound fluorine sum parameters in river water samples - Comparison of combustion ion chromatography (CIC) and high resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS) N2 - In this study, we compare combustion ion chromatography (CIC) and high resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS) with respect to their applicability for determining organically Bound fluorine sum parameters. Extractable (EOF) and adsorbable (AOF) organically bound fluorine as well as total fluorine (TF) were measured in samples fromriver Spree in Berlin, Germany, to reveal the advantages and disadvantages of the two techniques used as well as the two established fluorine sum Parameters AOF and EOF. TF concentrations determined via HR-CS-GFMAS and CIC were comparable between 148 and 270 μg/L. On average, AOF concentrations were higher than EOF concentrations, with AOF making up 0.14–0.81% of TF (determined using CIC) and EOF 0.04–0.28% of TF (determined using HR-CSGFMAS). The results obtained by the two independent methods were in good agreement. It turned out that HR-CS-GFMAS is a more sensitive and precise method for fluorine analysis compared to CIC. EOF and AOF are comparable tools in Risk evaluation for the emerging pollutants per- and polyfluorinated alkyl substances; however, EOF is much faster to conduct. KW - High resolution-continuum source-graphite furnace molecular absorption spectrometry (HR-CS-GFMAS) KW - Combustion ion chromatography (CIC) KW - Per- and polyfluorinated alkyl substances (PFASs) KW - Adsorbable organically bound fluorine (AOF) KW - Extractable organically bound fluorine (EOF) KW - Surface waters PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-515351 DO - https://doi.org/10.1007/s00216-020-03010-y SN - 1618-2650 VL - 413 IS - 28 SP - 103 EP - 115 PB - Springer CY - Berlin AN - OPUS4-51535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gentzmann, Marie A1 - Adam, Christian A1 - Vogel, Christian A1 - Gäbler, H.-E. A1 - Huthwelker, T. T1 - Investigation and comparison of Scandium species in different European bauxite residues by combination of novel analytocall tools N2 - In recent times, as the need for new high-tech materials is growing steadily to fulfil future sustainability goals, more and more looks turn towards industrial waste streams as potential sources of valuable metals. Bauxite residue (BR), accumulating during alumina production, is one of the major waste streams in the metal industry. Suitable re-use possibilities for BR are intensively investigated including approaches for the recovery of scandium (Sc). This transition metal, even though rarely recognized by the broader audience yet, has recently gained the interest of e.g. aerospace industries and SOFC-producers since its use is strongly improving the performance and durability of the respective materials. Even though many sources classify Sc as one of the REE, there are many aspects, such as its ionic radius, which significantly differentiate Sc from the REE and cause its behaviour to be distinct as well. The large ionic potential (radius/charge) causes Sc to be incompatible in most rock forming minerals, which results in generally low concentrations in the earth’s crust and rare occurrences of natural Sc-deposits. The general occurrence of enriched concentrations of Sc in some BRs compared to the earth’s crust is known for some time now and has especially been investigated for Greek materials. However, the (geo)chemical and mineralogical behaviour, the Sc speciation, the association and the variation of Sc occurrences in BRs of different origin is still not fully understood. This study aims to gain better knowledge on the different kinds of Sc-occurrences and their possible impact on future recovery schemes. We therefore apply a diverse set of analytical methods including novel measurement techniques such as X-ray absorption near edge structure (XANES) spectroscopy as well as standard techniques such as electron microprobe analyses, and Raman spectroscopy on BRs from Germany, Hungary and Greece. Information on the local distribution of Sc is determined by high-resolution laser ablation – inductively coupled plasma – mass spectrometry (LA-ICP-MS) mappings. Sc in Greek BR seems to have an affinity towards Fe-Phases such as Goethite and Hematite. However, whereas some of these phases show distinct enrichment of Sc, others are particularly barren, which might be a result of the different input materials. By means of XANES measurements it was possible to show that Sc in the Greek samples occurs adsorbed on the surface of those Fe-Phases, likely in the form of amorphous Sc-hydroxide or -oxyhydroxide or can be incorporated into the crystal lattice as well. The general affinity of Sc to those kinds of phases has been reported for natural rocks such as laterites before, where similar investigations were made using the XANES method [8]. Likewise, the Fe-association has been observed for Greek BR by Vind et al. [7]. Hungarian BRs show similar results as the Greek samples and LA-ICP-MS mappings show distinct Sc enrichment rims surrounding mineral particles. In German BR, Fe as well as Ti-phases occur to be partially enriched in Sc. Depending on the original primary bauxite, the source rock of the bauxite and the bauxite processing route, it is likely that many different parameters influence the occurrence and species of Sc in the BR. Theoretically, it either can therefore remain within its original carrier or can be partially or fully redistributed within the BR. Since the processing of the bauxite involves elevated temperatures, pressure and dissolving reagents, it is however very likely that some of the Sc will be redistributed and adsorb on mineral surfaces of smaller and larger particles, making beneficiation steps rather ineffective. The study shows that there is no general rule defining how Sc is associated mineralogically or chemically within BRs. Therefore, the effective development of a recovery method needs a case specific background knowledge on the Sc-species present in the BR of interest. This research has received funding from the European Community’s Horizon 2020 Programme SCALE (H2020/2014-2020) under grant agreement n° 730105. T2 - 3rd European Rare Earth Resources Conference (ERES) 2020 CY - Online meeting DA - 06.10.2020 KW - Red Mud KW - Scandium KW - Bauxite Residue PY - 2020 AN - OPUS4-51570 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gerrits, Ruben A1 - Pokharel, R. A1 - Breitenbach, Romy A1 - Radnik, Jörg A1 - Feldmann, Ines A1 - Schuessler, J.A. A1 - von Blanckenburg, F. A1 - Gorbushina, Anna A1 - Schott, J. T1 - How the rock-inhabiting fungus K. petricola A95 enhances olivine dissolution through attachment N2 - Free-living and mycorrhizal fungi are able to enhance the weathering of rock and other solid substrates. Deciphering the exact mechanisms of these natural processes requires their experimental simulation. Moreover, by performing these simulations with genetically amenable rock-weathering fungi, one can knock-out certain fungal traits and consequently identify their weathering-relevant function. Here, the effect of the rock-inhabiting fungus, Knufia petricola A95, on the dissolution kinetics of an Fe-bearing olivine (Mg1.86Fe0.19SiO4) is investigated at 25 °C and pH 6 using reproducible batch and mixed flow experiments. The availability of a melanin-deficient mutant (ΔKppks) of K. petricola A95, which produces more extracellular polymeric substances (EPS) than the wild type (WT), enables the comparative study of the role of melanin and EPS in olivine dissolution. In abiotic dissolution experiments, the olivine dissolution rate decreased considerably over time at pH 6 but not at pH 3.5. This inhibition of abiotic olivine dissolution at pH 6 was most likely caused by the in-situ oxidation of ferrous Fe and/or the precipitation of ferric hydroxides at the olivine surface. In corresponding biotic experiments at pH 6, both the wild type K. petricola and its melanin-deficient mutant ΔKppks solubilised and bound significant amounts of Fe released by olivine dissolution. Fe oxidation and precipitation were thus prevented and olivine dissolution proceeded faster than in the abiotic experiments. By sequestering Fe directly at the olivine surface, the attached wild type K. petricola cells were particularly efficient at preventing the oxidation of Fe at the mineral surface: the slowdown of olivine dissolution almost completely disappeared. The attachment capacity of these wild type cells is most likely mediated by wild type-specific EPS. Our presented experimental systems allow the oxidation of mineral-released Fe and include a rock-inhabiting fungus, thus simulating chemical, physical and biological conditions that set dissolution rates in a way that is relevant to natural ecosystems. KW - Black fungi KW - Bio-weathering KW - Forsterite KW - Knock-out mutant KW - Extracellular polymeric substances KW - Melanin Adhesion PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509332 DO - https://doi.org/10.1016/j.gca.2020.05.010 VL - 282 SP - 76 EP - 97 PB - Elsevier Ltd. AN - OPUS4-50933 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ghigo, Tea A1 - Rabin, Ira T1 - Gaining Perspective into the Materiality of Manuscripts: The Contribution of Archaeometry to the Study of the Inks of the White Monastery Codices N2 - An interdisciplinary approach to the study of manuscript traditions is here applied to the analysis of the leaves from the White Monastery, one of the greatest centres of literary production in Late Antique Egypt. In the framework of the ‘PAThs’ project, archaeometric analyses complement the information pieced together by a range of disciplines in the field of humanities. The use of different complementary analytical techniques provides information on the type of ink used and its elemental composition, unveiling interesting details regarding the materials and methodology of manufacturing of writing media. Moreover, this contribution takes a step forward and discusses the possible existence of a regional arrangement in the elemental composition revealed in the inks studied. KW - Manuscript making KW - Archaeometry KW - Ink analysis KW - Interdisciplinary approach KW - Coptic studies PY - 2020 SP - 273 EP - 282 AN - OPUS4-51003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ghigo, Tea A1 - Rabin, Ira A1 - Buzi, P. T1 - Black Egyptian inks in Late Antiquity: new insights on their manufacture and use N2 - We present here our methodological approach applied to the study of Egyptian inks in Late Antiquity. It is based on an interdisciplinary strategy, bringing together a variety of disciplines from humanities and natural sciences, and it aims at systematically collecting a statistically relevant amount of data regarding the composition of the inks. The application of a wellestablished, non-invasive protocol that includes near-infrared imaging and X-ray fluorescence spectroscopy for in situ measurements enables the identification and characterisation of inks dating from the end of Late Antiquity onwards. However, sometimes this method limits our understanding when characterising more ancient inks. Trying to overcome these limitations, the potential of a new device for the characterisation of organic compounds is here explored by conducting preliminary tests on mock samples. In this work, we present the results from 77 codicological units that include some of the earliest manuscripts of our corpus that presently lists 159 units. KW - Ink KW - Archaeometry KW - Manuscripts KW - Coptic KW - Egypt PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-503893 DO - https://doi.org/10.1007/s12520-019-00977-3 VL - 12 IS - 3 SP - 1 EP - 14 PB - Springer AN - OPUS4-50389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Ghigo, Tea A1 - Torallas, S. T1 - Between Literary and Documentary Practices: The Montserrat Codex Miscellaneus (Inv. Nos. 126‐178, 292, 338) and the Material Investigation of Its Inks N2 - The Montserrat Codex Miscellaneus (TM 59453/LDAB 552) has been the subject of numerous studies since the publication of ist first text by its owner, father Ramon Roca-Puig. Scholars have dealt with the content of its texts, as well as interrogated its origin and materiality. It is a fourth-century papyrus single quire codex, which contains texts in both Latin and Greek. It has been argued that it belonged to the Bodmer library, connected to a Pachomian library in the Thebaid. In this paper we want to contribute to the material study of the codex by presenting the first results of an archaeometric analysis performed upon the inks. The Analysis was carried out within the framework of the ‘PAThs’ project based at Sapienza University of Rome, and executed with the close cooperation of DVCTVS, a team of scholars who curate the Roca-Puig collection. The results obtained have not only cast light on the history of production of the codex, but also, and perhaps most importantly, point out that a meaningful interpretation of the analytical data is only possible through an interdisciplinary collaboration between the humanities and the natural sciences. KW - Interdisciplinary approach KW - Codex Miscellaneus KW - Palaeography KW - Book production KW - Archaeometry KW - Ink analysis PY - 2020 SP - 101 EP - 114 AN - OPUS4-51004 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -