TY - CHAP A1 - Wünsch, Christoph A1 - Simon, Franz-Georg ED - Maletz, Roman ED - Dornack, Christina ED - Ziyang, Lou T1 - The reduction of greenhouse gas emissions through the source-separated collection of household waste in Germany N2 - The production of secondary materials from waste materials requires, in most cases, significantly lower energy amounts than the primary material production of raw materials. Along with lower energy demand, the greenhouse gas emissions produced are also lower. The duty of a modern waste management system should therefore be to collect and sort the waste materials in a way that the highest amounts of single material fractions with the highest qualities can be generated. In this contribution, the greenhouse gas balances of the theoretical treatment of the household waste, if collected as mixed waste in sanitary landfills, in waste incineration plants, or in mechanical-biological treatment plants, are compared to the existing separate waste collection and treatment in Germany in 2014. The results show that the treatment of the mixed collected household waste in sanitary landfills would lead to a significant release of greenhouse gases. The treatment in MBTs with the recovery of valuables and the further disposal of the biologically stabilized fraction on landfills, as well as the treatment of the high calorific fraction (also called refuse derived fuel – RDF) in RDF plants, coal-fired power plants, or cement kilns, would lead to small amounts of avoided greenhouse gas emissions. The thermal treatment in waste incineration plants would lead to moderate amounts of avoided greenhouse gases. Only with the actually practiced separate collection and treatment of household waste were significant amounts of greenhouse gas emissions avoided. In total, this is approximately 5.5 million tons of carbon dioxide equivalents for approximately 45.5 million tons of separate collected and treated household waste in Germany in 2014. KW - Greenhouse gas accounting KW - Greenhouse gas mitigation KW - Household waste KW - Material recycling KW - Separate collection PY - 2018 SN - 978-3-319-69071-1 DO - https://doi.org/10.1007/698_2017_35 VL - 63 SP - 269 EP - 287 PB - Springer International Publishing CY - Berlin ET - 1 AN - OPUS4-44937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Vogel, Christian A1 - Kalbe, Ute T1 - Antimony and vanadium in incineration bottom ash – leaching behavior and conclusions for treatment processes N2 - Due to its large mineral fraction, incineration bottom ash (IBA) from municipal solid waste incineration is an interesting raw material that can be used for road construction or to produce secondary building materials. However, leaching chloride, sulfate, and potentially harmful heavy metals may cause problems in using IBA in civil engineering. Investigating leaching behavior is crucial for the assessment of the environmental compatibility of IBA applications. Various test procedures are available for that purpose. In the present study, a long-term leaching test of a wet-mechanically treated IBA was performed in a lysimeter for almost six years. While concentrations of chloride, sulfate and the majority of the heavy metals started to decrease rapidly with progressive liquid-to-solid ratio (L/S), antimony (Sb) and vanadium (V) behaved differently. At the beginning of the lysimeter test, the Sb and V concentrations were low, but after approximately one year of operation at an L/S ratio of around 0.8 L/kg, a steady increase was observed. It was shown that this increase is the result of low Ca concentrations due to the formation of CaCO3. With the data, the solubility products from Ca-antimonate and Ca-vanadate were calculated. The unusual leaching behavior of Sb and V should be kept in mind when considering field scenarios and evaluating the impact on the environment. KW - Bottom ash KW - Lysimeter KW - Leaching of waste materials KW - Secondary building materials PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-534317 DO - https://doi.org/10.31025/2611-4135/2021.15115 SN - 2611-4135 VL - 16 SP - 75 EP - 81 PB - CISA CY - Padua AN - OPUS4-53431 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Barqawi, Haitham A1 - Chubarenko, B. A1 - Esiukova, E. A1 - Putna-Nimane, I. A1 - Barda, I. A1 - Strode, E. A1 - Purina, I. ED - Köppen, S. ED - Reckermann, M. T1 - EI‐GEO environmental impact of geosynthetics in aquatic systems N2 - EI‐GEO is a multinational research project (Germany, Latvia, Russia) funded under the ERA.Net RUS Plus Call 2017. Aim of the project is the investigation whether geosynthetics in hydraulic engineering applications could be a source of microplastics (MPs) and other contaminants to the aquatic environment causing negative effects to aquatic organisms. Whereas the behavior of geosynthetics in landfill engineering is well studied and documented since decades, little is known on application in applications such as coastal protection or ballast layers for wind energy plants. However, due to the rapid expansion of offshore wind energy, rising water levels and more extreme weather conditions as a result of climate change more and more hydraulic engineering projects will be realized in the future. Applied methods are artificial ageing of geosynthetics in environmental simulation chambers, storage of samples under environmental condition for comparison with laboratory simulation, sample characterization by microscopic methods and ecotoxicological testing of water in contact with geosynthetics. In parallel a case study at the Baltic Sea shore at Kaliningrad Oblast (Russia) will be performed. The aim of study is to estimate the level of pollution of the beaches by geosynthetic debris and identify the possible sources. T2 - 3rd Baltic Earth Conference CY - Online meeting DA - 02.06.2020 KW - Geosynthetics KW - Micro plastic KW - Hydraulic engineering PY - 2020 UR - https://www.baltic-earth.eu/hel2020/material/3rd_BalticEarth_Conference_Proceedings.pdf SN - 2198-4247 SP - 151 EP - 152 PB - International Baltic Earth Secretariat Publications CY - Geesthacht AN - OPUS4-50881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Franz-Georg A1 - Haas, Marco A1 - Pienkoß, Fabian A1 - Kwiatkowski, Robert T1 - Wet-mechanical treatment: Processing of bituminous road construction waste in a jigging machine N2 - Jigging machines are used in processing technology in many areas. Examples are the processing of coal, ores, and primary and secondary raw and waste materials. Even small differences in density are offen sufficient for successful sorting. In the work presented here, milled material from road construction waste contaminated with bitumen is to be separated from uncontaminated material. In this way, scarce landfill space could be saved and mineral material be returned to the material cycle. KW - Wet-mechanical treatment KW - Jig KW - Road construction waste PY - 2023 UR - https://www.at-minerals.com/de/artikel/aufbereitung-von-bitumenhaltigem-strassenaufbruch-in-einer-setzmaschine-4037512.html SN - 1434-9302 VL - 64 IS - 12 SP - 46 EP - 51 PB - Bauverlag BV GmbH CY - Gütersloh AN - OPUS4-59160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Chubarenko, B. A1 - Purina, I. T1 - Approach for analysis of environmental impact of geosynthetics in aquatic systems by example of the Baltic Sea N2 - Whereas the behavior of geosynthetics in landfill engineering is well studied and documented since decades, little is known on application in applications such as coastal protection or ballast layers for wind energy plants. However, due to the rapid expansion of offshore wind energy, rising water levels and more extreme weather conditions as a result of climate change more and more hydraulic engineering projects will be realized in the future. Construction with geosynthetics has various advantages, but it has to be ensured that there is no negative environmental impact from the application of geosynthetics in hydraulic engineering. It is expected that any effect will be visible only on the long-term. Therefore, accelerated testing is needed to derive requirements for geosynthetics in hydraulic engineering. T2 - 7th IEEE/OES Baltic Symposium, Clean and Safe Baltic Sea and Energy Security for the Baltic countries CY - Klaipeda, Lithuania DA - 12.06.2018 KW - Geosynthetics KW - Artificial ageing KW - Micro plastic PY - 2018 AN - OPUS4-45206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg T1 - Product testing and performance N2 - Geosynthetic materials are applied in measures for coastal protection. Weathering or any damage of constructions, as shown by a field study in Kaliningrad Oblast (Russia), could lead to the littering of the beach or the sea (marine littering) and the discharge of possibly harmful additives into the marine environment. The ageing behavior of a widely used geotextile made of polypropylene was studied by artificial accelerated ageing in water-filled autoclaves at temperatures of 30 to 80° C and pressures of 10 to 50 bar. Tensile strength tests were used to evaluate the progress of ageing, concluding that temperature rather than pressure was the main factor influencing the ageing of geotextiles. Using a modified Arrhenius equation, it was possible to calculate the half-life for the loss of 50% of the strain, which corresponds to approximately 330 years. T2 - EuroGeo-7, Session Geosynthetics, Sustainability and Current Industry Challenges CY - Warschau, Poland DA - 04.09.2022 KW - Geosynthetics KW - Ageing KW - Autoclave tests PY - 2022 AN - OPUS4-55671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Kalbe, Ute A1 - Bandow, Nicole T1 - Potential use of incineration bottom ash in construction – Evaluation of environmental impact N2 - The results from a long-term lysimeter experiment with incineration bottom ash irrigated with artificial rain are reported. Whereas chloride concentration dropped significantly, the release of antimony increased during the course of the experiment as a result of aging processes. T2 - 10th International Conference on the Environmental and Technical Implications of Construction with Alternative Materials, WASCON 2018 CY - Tampere, Finland DA - 06.06.2018 KW - Leaching KW - MSWI Bottom Ash KW - Lysimeter KW - Antimony PY - 2018 SN - 978-951-758-631-3 SN - 0356-9403 SP - 108 EP - 110 AN - OPUS4-45416 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Vogel, Christian A1 - Simon, Franz-Georg T1 - Antimony in incineration bottom ash – Leaching behavior and conclusions for treatment processes N2 - Antimony (Sb) is used in industrial products mainly as flame retardant in plastic material. Due to such additives in plastics, about a half of Sb ends up in municipal solid waste incineration at the end-of-life and consequently in relevant amounts in the generated bottom ash. In contact with water, the initial leachability is low, as antimonates form sparingly soluble compounds with Ca2+. Following the carbonation of the incineration bottom ash (IBA) during the proceeding ageing the pH in the leachates decreases. With decreasing concentration of Ca in the eluate the solution equilibrium changes and antimonates dissolve. In Germany it is intended to regulate Sb in IBA with the planned implementation of the so called Mantelverordnung (MantelVO, containing provisions on the utilisation of mineral waste) in the near future. The limit values set in the draft might be critical for IBA and therefore pose a risk for the utilisation of the mineral fraction of IBA in the well-established recycling routes. T2 - SUM 2020 – 5th Symposium on Urban Mining and Circular Economy CY - Online meeting DA - 18.11.2020 KW - Bottom ash KW - Leaching KW - Antimony PY - 2020 SP - 1 EP - 4 AN - OPUS4-51622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Abis, M. A1 - Bruno, M. A1 - Simon, Franz-Georg A1 - Grönhom, R. A1 - Kuchta, K. A1 - Fiore, S. ED - Medici, F. T1 - A Novel Dry Treatment for Municipal Solid Waste Incineration Bottom Ash for the Reduction of Salts and Potential Toxic Elements N2 - The main obstacle to bottom ash (BA) being used as a recycling aggregate is the content of salts and potential toxic elements (PTEs), concentrated in a layer that coats BA particles. This work presents a dry treatment for the removal of salts and PTEs from BA particles. Two pilotscale abrasion units (with/without the removal of the fine particles) were fed with different BA samples. The performance of the abrasion tests was assessed through the analyses of particle size and moisture, and that of the column leaching tests at solid-to-liquid ratios between 0.3 and 4. The results were: the particle-size distribution of the treated materials was homogeneous (25 wt % had dimensions <6.3 mm) and their moisture halved, as well as the electrical conductivity of the leachates. A significant decrease was observed in the leachates of the treated BA for sulphates (44%), chlorides (26%), and PTEs (53% Cr, 60% Cu and 8% Mo). The statistical analysis revealed good correlations between chloride and sulphate concentrations in the leachates with Ba, Cu, Mo, and Sr, illustrating the consistent behavior of the major and minor components of the layer surrounding BA particles. In conclusion, the tested process could be considered as promising for the improvement of BA valorization. KW - Bottom ash KW - Dry treatment KW - Municipal solid waste PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-552161 SN - 978-3-0365-3063-5 DO - https://doi.org/10.3390/ma14113133 SP - 57 EP - 71 PB - MDPI CY - Basel AN - OPUS4-55216 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Syc, M. A1 - Simon, Franz-Georg A1 - Biganzoli, L. A1 - Grosso, M. A1 - Hyks, J. ED - Holm, O. ED - Thome-Kozmiensky, E. T1 - Resource recovery from incineration bottom ash: Basics, concepts, principles N2 - Waste-to-energy (WtE) is one of the leading technologies for municipal solid waste (MSW) treatment in Europe. According to Eurostat data, in 2015, 27 % of MSW was utilized in WtE plants, which represents more than 80 million tons per year. Therefore, the European annual production of incineration bottom ash (IBA) is about 20 million tons, as it is about 25 wt% of input MSW. In the European List of Waste, IBA is listed as mirror entry (i.e. waste materials which should be classified as either non-hazardous or hazardous, depending on its hazardous properties and/or content of hazardous substances) under codes 19 01 11 and 19 01 12. Recent trends indicate that WtE allows, apart from utilization of the energy content of waste, also the recovery of various valuable components. Hence, WtE can be included in the key technologies that can put the circular economy concept into practice. Secondary raw materials in the case of WtE are solid residues, especially IBA, as it is a secondary source, particularly of ferrous metals (Fe) and non-ferrous metals (NF) and glass. Moreover, the residual mineral fraction can be used for various applications in the construction industry, i.e. as aggregates substitute for bound or unbound applications, in cement manufacturing or, as indicated by recent research, also in more sophisticated applications, e.g. for ceramics production. Recovery of these metals can also cause huge greenhouse gas savings. Alone in Europe, metal recovery from IBA reduces greenhouse gas emissions by approximately 3.2 million tonnes of CO2 equivalent. KW - Bottom ash KW - Recovery PY - 2018 SN - 978-3-944310-44-2 VL - 1 SP - 1 EP - 10 PB - Thomé-Kozmiensky Verlag GmbH CY - Neuruppin ET - 1 AN - OPUS4-46146 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -