TY - CONF A1 - Feldkamp, Martin T1 - Evaluation of Heat Fluxes in Fire Reference Test Conducted in BAM Propane Gas Fire Test Facility N2 - Packages for the transport of intermediate- and high-level radioactive waste are designed to withstand severe accidents. The International Atomic Energy Agency (IAEA) has established specific mechanical and thermal tests. Packages for the transport of radioactive material must withstand these tests to comply with the Regulations for the Safe Transport of Radioactive Materials IAEA [IAEA (2018)]. A fire reference package was developed with the primary objective to demonstrate that the fire meets the regulatory requirements. Another aim is to characterise the boundary conditions of the actual fire as input parameters for thermo-mechanical simulations. A simple method to characterise the boundary conditions of a real steady state fire with a fire reference package is presented. The thermal test mainly consists of a 30 minute fully engulfing 800°C pool fire or an equally severe fire, such as a propane gas fire. The fire reference tests are performed prior to the actual fire test with the real package. The heat fluxes into the package depend substantially on the fire characteristics and the surface temperature of the package. To investigate local and overall heat fluxes over a wide range of surface temperatures in this test facility a fire reference package was designed for repeated use. The fire reference package presented in this paper represents the outer geometry of a small transport container for radioactive material and is used as a device in civil engineering. It is designed as a closed steel sheet cylinder with a wall thickness of 10 mm, a length of 182 mm and a diameter of 102 mm. The package was instrumented with thermocouples and filled with heat resistant insulation material. Open-air fire tests were performed in a BAM propane gas fire test facility with the fire reference package. The measured temperatures are used to determine the changes of heat fluxes into the fire reference package in relation to the package surface temperature. The calculated heat fluxes allow its fitting to express the thermal exposure as simple mathematical boundary condition. Therefore, in a first approach, fire properties such as adiabatic surface temperature (AST) as proposed by Wickström et al. (2007), convection coefficient and emissivity are determined mathematically fitting the heat flux development presented in this paper. The evaluated results provide an initial picture of local fire characteristics of the conducted propane gas fire and are a further development of previous works from Feldkamp et al. (2020). The results can be used in thermal and thermo-mechanical models to simulate the load on the real transport package in fire. The test shows that the examined propane gas fire covers the IAEA-fire over a wide range of surface temperatures with the chosen test stand parameters. T2 - SMiRT 27 (27th conference on Structural Mechanics in Reactor Technology) CY - Yokohama, Japan DA - 03.03.2024 KW - Fire KW - Propane KW - Fire Reference Test PY - 2024 AN - OPUS4-59680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad A1 - Quercetti, Thomas A1 - Sterthaus, Jens A1 - Ballheimer, Viktor T1 - Experimental and numerical investigation of prestressed bolt connections under lateral displacements N2 - The containment system of transport packages for spent nuclear fuel and high-level waste usually includes bolted lids with metal gaskets. The packages are assessed to specific transport conditions which are specified in the IAEA safety standards SSR-6 (IAEA 2018). These transport conditions, especially the so-called accident conditions of transport, imply high dynamic loading on the lids and the bolt connections of the package. The response of the lid systems on the mechanical accident conditions is generally investigated by experimental drop tests or numerically, e.g., by finite element analyses. The interpretation of the drop test results for the verification of the numerical models is often not obvious due to the complex superposition of different effects in the real tests. BAM has started a research project to get a better understanding about the behavior of prestressed bolt connections under loadings typical for these drop tests. In this context an experimental test set-up was developed to investigate the response of a single bolt connection under a prescribed lateral displacement of clamped parts. The bolt is instrumented by strain gauges to get the pretensional, the torsional and the bending stress in the bolt shank. Furthermore, the lateral movement and the tilt of the bolt head is measured during the test. A finite element model of the test set-up has been created in Abaqus FEA (Simulia 2021). The very detailed instrumentation of the test set-up shall give the opportunity to investigate and validate the numerical model. The aim of this paper is to give an overview about the proposed research project and to present first results. T2 - SMIRT 26 (26th conference on Structural Mechanics in Reactor Technology) CY - Potsdam, Germany DA - 10.07.2022 KW - Bolt connections KW - Finite element anaylsis KW - Experimental testing KW - Transport package for radioactive materials PY - 2022 UR - https://www.lib.ncsu.edu/resolver/1840.20/40614 SP - 1 EP - 7 PB - IASMiRT AN - OPUS4-59378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Komann, Steffen A1 - Wille, Frank A1 - Schubert, Sven T1 - Neue Regel für das Alterungsmanagement N2 - Die Regelwerksanforderungen für Verpackungen für den Transport radioaktiver Stoffe basieren auf den Empfehlungen der IAEA und werden über die verkehrsträgerspezifischen internationalen Regelwerke in nationales Recht umgesetzt. Um die Anforderungen des Regelwerkes zu erläutern, entwickelt die Bundesanstalt für Materialforschung und -prüfung (BAM) Gefahrgutregeln (BAM-GGR), welche die Entwickler, Hersteller und Betreiber von Behältern über die von der BAM angewandten Verfahren bei der Umsetzung gesetzlicher Bestimmungen informieren und unterstützen sollen. KW - Gefahrgut KW - Radioaktive Stoffe KW - Alterung KW - Transport PY - 2023 VL - 2023 IS - 9 SP - 16 EP - 18 PB - Heinrich Vogel CY - München AN - OPUS4-58577 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Neumeyer, Tino A1 - Ballheimer, Viktor A1 - Wille, Frank T1 - Investigations of Aged Metal Seals for Transport Package Safety Assessment N2 - Acceptable limits for activity release from transport casks for high-level radioactive material specified in the IAEA regulations must be kept by the integrity of cask body and the cask sealing system. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. One of the fundamental aspects in assessment is the specification of conservative package design leakage rates. To ensure the required package tightness for both, storage, and transport of the cask before and after storage usually metal seals of the Helicoflex® Type are used. Due to the long-term use the seal behavior is influenced by temperature and time. The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport specified in the regulations can have a significant effect on the leak tightness of the sealing system. Whereas the safety for application of new, non- aged Helicoflex® seals is verified sufficiently, there are still technical data gaps concerning the efficiency of aged Helicoflex® seals. BAM performed experiments to learn more about the sealing efficiency of aged Helicoflex® seals with Aluminum and Silver outer jackets. The seals were compressed in test-flanges and for artificial ageing the complete flange systems were stored in an oven for several month at a high temperature. During the compression and decompression tests after the aging, load-deformation characteristics of the seals, and leakage rates were measured. With these tests a load situation was simulated, which can occur in the regulatory drop test of the cask: Under high impact loads the bolted lid can lift a little for a short moment, allowing a little movement of the seal, so that the contact area can change before compressing again. The poster presentation will show details about test conditions and first results. T2 - Interdisciplinary research symposium on the safety of nuclear disposal practices safeND2023 CY - Berlin, Germany DA - 13.09.2023 KW - Radioactive material KW - Sealing KW - Ageing KW - Leaktightnes PY - 2023 AN - OPUS4-58436 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Fire Reference Tests for Qualification of IAEA Fire N2 - A small cylindrical fire reference package was designed. A fire test setup was created using the fire reference package in accordance with IAEA standards. Four propane gas fire tests were conducted to determine heat fluxes into the fire reference package. The initial test setup was modified to create the final design of the fire test facility. This allowed for the heat flux to be adjusted to meet the regulatory IAEA fire qualification criteria. Furthermore, a numerical model of the fire reference package was created using boundary conditions derived from the experimental data. The simulation results demonstrated good agreement with the experimental data and provided additional insights. T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Cadarache, France DA - 13.10.2022 KW - Fire KW - IAEA KW - Propane PY - 2022 AN - OPUS4-57251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian T1 - Development of a Hydrogen Fire Test Rig for Thermal Testing N2 - A new hydrogen-based test rig is being developed for a feasibility study on the use of hydrogen as an energy source for thermal testing in accordance with the IAEA SSR-6 guidelines for transport packages containing radioactive materials. The test rig will be capable of combusting hydrogen for a wide range of different burner geometries, mass flows and if necessary hydrogen blends. As this type of fire test according to the IAEA boundary conditions (SSR-6 & SSG-26) does not yet exist, a large number of preliminary investigations, safety assessments and calculations must be carried out in order to develop a viable concept for hydrogen fires. T2 - 1st JF BMUV Förderprogramm CY - Berlin, Germany DA - 22.05.2024 KW - IAEA Fire KW - H2 Fire KW - IAEA Regulations PY - 2024 AN - OPUS4-60555 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Transport nach Zwischenlagerung, Besonderheiten des letzten Transports N2 - Transportierbarkeit von Transport- und Lagerbehältern für radioaktive Stoffe, welche nach eine längerfristigen trockenen Zwischenlagerung transportiert werden müssen. Überblick über die aktuellen Regelwerke und Richtlinien sowie die Zeitpläne für das Finden eines Endlagers für hochradioaktive Stoffe und die damit verbundene verlängerte Zwischenlagerung. Des Weiteren werden das für die verlängerte Zwischenlagerung notwendige Alterungsmanagement und die noch erforderlichen Forschungstätigkeiten vorgestellt. T2 - BGZ Fachworkshop Zwischenlagerung CY - Berlin, Germany DA - 16.11.2021 KW - Transportbehälter KW - Radioaktive Stoffe KW - Transport KW - Zwischenlagerung KW - IAEA PY - 2021 AN - OPUS4-60505 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Verkehrsrechtliche Betrachtungen Transport- und Lagerbehälter - Wo geht die Reise hin? N2 - Transportierbarkeit von Transport- und Lagerbehältern für radioaktive Stoffe, welche nach eine längerfristigen trockenen Zwischenlagerung transportiert werden müssen. Überblick über die aktuellen Regelwerke und Richtlinien sowie die Zeitpläne für das Finden eines Endlagers für hochradioaktive Stoffe und die damit verbundene verlängerte Zwischenlagerung. Des Weiteren werden das für die verlängerte Zwischenlagerung notwendige Alterungsmanagement und die noch erforderlichen Forschungstätigkeiten vorgestellt. T2 - 10. Symposium Lagerung und Transport radioaktiver Stoffe CY - Hannover, Germany DA - 05.09.2023 KW - Transportbehälter KW - Radioaktive Stoffe KW - Transport KW - Zwischenlagerung KW - IAEA PY - 2023 AN - OPUS4-60506 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian T1 - Development of a Hydrogen Fire Test Rig for Thermal Testing N2 - A new hydrogen-based test rig is being developed for a feasibility study on the use of hydrogen as an energy source for thermal testing in accordance with the IAEA SSR-6 guidelines for transport packages containing radioactive materials. The test rig will be capable of combusting hydrogen for a wide range of different burner geometries, mass flows and if necessary hydrogen blends. As this type of fire test according to the IAEA boundary conditions (SSR-6 & SSG-26) does not yet exist, a large number of preliminary investigations, safety assessments and calculations must be carried out in order to develop a viable concept for hydrogen fires. T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Berlin, Germany DA - 04.06.2024 KW - IAEA Fire KW - H2 Fire KW - IAEA Regulations PY - 2024 AN - OPUS4-60554 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Experimental And Numerical Analyses For The Evaluation Of Heat Fluxes Of A Fire Reference Test N2 - Packages for the transport of high-level radioactive material are designed to endure severe accidents. To obtain approval, these transport packages must adhere to the specification-based criteria of the IAEA SSR-6 [1]. To ensure compliance with these requirements, specific mechanical and thermal tests need to be appointed with respect to the package type. Typically, IAEA SSR-6 [1] prescribes mechanical tests followed by a thermal fire test as part of a cumulative test sequence. To approve the fire test, BAM uses a reference package representing the original package in its outer geometry for characterizing the actual fire and its impact on the package. This serves a dual purpose: it allows the precise adjustment of experimental parameters for the package design to be approved, and it provides input parameters for thermomechanical simulations, cf. [2]. With the help of this methodology for characterizing boundary conditions of the package, temperature evolutions within the reference package can be studied in a Finite-Element Analyses (FEA). This helps to compare the experiments with the numerical simulations on the case of the reference package, but also serves at the same time for preliminary simulations with the package design to be approved. The thermal test consists of a 30-minute fully engulfing 800°C pool fire or an equally severe fire, e.g. a propane gas fire. The fire reference test is performed prior to the regulatory fire test with the package design to be approved. The fire reference package in the described case is a closed sheet 316L steel cylinder with a wall thickness of 10 mm, a length of 182 mm, and a diameter of 102 mm. The package was instrumented with thermocouples and filled with heat resistant insulating material. T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Experimental KW - Numerical KW - Heat Flux KW - Reference Test PY - 2024 AN - OPUS4-60847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Safety Aspects for Transport Containers with regard to Ageing and Battery Accident Scenarios N2 - In Germany, the search for a final repository for highly radioactive material is currently based on the assumption that interim storage will take considerably longer than was anticipated. At that time, authorization procedures assumed that interim storage would be brief, until the containment systems could be placed in a final repository. For today's new approvals and extensions, the IAEA (International Atomic Energy Agency) regulations for the transport of radioactive material require an assessment of all components and component groups with regard to ageing. To assess the safety requirements not only over the previously envisaged periods but also over long durations, numerous individual parts and component groups must be examined and evaluated for ageing and interactions between materials. The metal seals of a double lid sealing system, for example, are critical components that must be studied with respect to ageing. In a containment system for radioactive material, metal seals must not only undergo classic ageing, but also withstand mechanical influences and radiation over extended periods. In addition to assessments by the applicants, BAM must also independently analyze and evaluate these ageing mechanisms as part of its sovereign mandate. Another challenge in both new approvals and extensions is the assessment of transport regarding changes in the state of the art, which are not synchronously assessed in the regulations. In transporting radioactive material, a classic oil fire has been assumed in a hypothetical accident scenario from the development of the regulations to the present day. Due to the rapid development of propulsion technologies in recent years, such as battery or hydrogen-powered vehicles, investigations must be conducted in the revision process of the IAEA regulations to assess the impact of these new technologies on safety assessments. It is important for the member states of the IAEA to know whether new technologies are covered by the regulations or if changes are necessary to continue issuing international licenses. By focusing on batteries from the material to the cell to the module and the application, BAM contributes to the evaluation of batteries at every step of the chain. In addition to the safety of current and new battery technologies, BAM also endeavors to address issues of compositional trace and sustainable energy materials. T2 - MSD: Leaf CY - Livermore, CA , USA DA - 07.08.2024 KW - Safety Aspects KW - Ageing KW - Accident Scenarios KW - Battery PY - 2024 AN - OPUS4-60851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian T1 - Experimental and Numerical Analyses for the Evaluation of Hydrogen as an Energy Source for Thermal Testing of Transport Packages of Radioactive Material N2 - In this paper we present a new hydrogen-based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials. The test rig will be capable of combusting hydrogen for a wide range of different burner geometries, mass flows and if necessary hydrogen blends. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and calculations must be carried out in order to develop a viable concept for hydrogen fires. In the first step of the feasibility study, the temperature, structure, and radiation of various hydrogen flames are surveyed. In future works, the results will make it possible to design burner frames that are suitable for fire reference tests in order to make comparisons with pool and propane fires used in assessment procedures today. In parallel comparative numerical simulations are conducted to model the thermal behaviour of hydrogen flames using the software package Ansys®. On the one hand, the numerical simulations support the experiments by providing an overview of numerous parameters and the measuring range; on the other hand, they will help with the design of the burner frame in future work. This paper gives an overview in the design and capabilities of the test rig. Furthermore, the results of the parameter studies show that burner geometry and mass flow provide a significant design margin for the thermal shape of the hydrogen flames. In addition, the results of the initial numerical calculations will be used to determine the necessary sensors, the positions, and their operating range. Only the optimal interaction allows a controlled system that permits user-defined hydrogen fires. T2 - PVP2024, Pressure Vessels & Piping Conference CY - Bellevue, Washington, USA DA - 29.07.2024 KW - Hydrogen KW - Fire KW - IAEA Regulations KW - CFD KW - Burner PY - 2024 AN - OPUS4-60855 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Wille, Frank ED - Czarwinski, R. T1 - Radioaktive Stoffe in besonderer Form-wichtige Aspekte im Zulassungsverfahren N2 - Für die Beförderung von umschlossenen radioaktiven Stoffen (Strahler) können Transporterleichterungen gelten, wenn das Strahlerdesign nachweislich unfallsicher ausgelegt ist und eine Zulassung als radioaktiver Stoff in besonderer Form vorliegt. Die in Deutschland zuständige Behörde für die Prüfung und Zulassung radioaktiver Stoffe in besonderer Form ist die Bundesanstalt für Materialforschung und –prüfung (BAM). Eine oft langfristige Nutzung der Strahler kann eine alterungsbedingte Schwächung der Umschließung des radioaktiven Stoffes zur Folge haben. Jeder Strahler einer zugelassenen Bauart muss jedoch im Beförderungsfall zu jeder Zeit, auch nach längerer Nutzung, den vorgeschriebenen Prüfanforderungen genügen. Die Alterungsbewertung auf der Grundlage einer vom Antragsteller zu spezifizierenden Nutzungsdauer des radioaktiven Stoffes in besonderer Form ist seit langer Zeit Bestandteil des Zulassungsverfahrens in Deutschland. Ein von Deutschland eingebrachter Vorschlag im Rahmen der anstehenden Revision der IAEA Empfehlungen für die sichere Beförderung von radioaktiven Stoffen (SSR-6) soll die Lesbarkeit des Regelwerkes bezüglich der Alterungsbewertung verbessern, Klarheit über die damit verbundenen Anforderungen erzeugen und damit zu einer Harmonisierung der Zulassungsverfahren auf internationaler Ebene beitragen. In diesem Beitrag sollen wichtige Einflussfaktoren auf das Alterungsverhalten von radioaktiven Stoffen in besonderer Form aufgezeigt und die Notwendigkeit für die Spezifikation einer Nutzungsdauer als Grundlage für die Alterungsbewertung begründet werden. Der deutsche Vorschlag für die Revision des IAEA Regelwerks zum sicheren Transport radioaktiver Stoffe (SSR-6) wird vorgestellt und erläutert. T2 - Jahrestagung des FS 2022 CY - Konstanz, Germany DA - 26.09.2022 KW - Strahlenschutz KW - Radioaktive Stoffe KW - Beförderung KW - Zulassung PY - 2022 SN - 1013-4506 SP - 15 EP - 20 PB - Fachverband für Strahlenschutz e.V. CY - Berlin AN - OPUS4-56134 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette T1 - Radioaktive Stoffe in besonderer Form - wichtige Aspekte im Zulassungsverfahren N2 - Für die Beförderung von umschlossenen radioaktiven Stoffen (Strahler) können Transporterleichterungen gelten, wenn das Strahlerdesign nachweislich unfallsicher ausgelegt ist und eine Zulassung als radioaktiver Stoff in besonderer Form vorliegt. Die in Deutschland zuständige Behörde für die Prüfung und Zulassung radioaktiver Stoffe in besonderer Form ist die Bundesanstalt für Materialforschung und –prüfung (BAM). Eine oft langfristige Nutzung der Strahler kann eine alterungsbedingte Schwächung der Umschließung des radioaktiven Stoffes zur Folge haben. Jeder Strahler einer zugelassenen Bauart muss jedoch im Beförderungsfall zu jeder Zeit, auch nach längerer Nutzung, den vorgeschriebenen Prüfanforderungen genügen. Die Alterungsbewertung auf der Grundlage einer vom Antragsteller zu spezifizierenden Nutzungsdauer des radioaktiven Stoffes in besonderer Form ist seit langer Zeit Bestandteil des Zulassungsverfahrens in Deutschland. Ein von Deutschland eingebrachter Vorschlag im Rahmen der anstehenden Revision der IAEA Empfehlungen für die sichere Beförderung von radioaktiven Stoffen (SSR-6) soll die Lesbarkeit des Regelwerkes bezüglich der Alterungsbewertung verbessern, Klarheit über die damit verbundenen Anforderungen erzeugen und damit zu einer Harmonisierung der Zulassungsverfahren auf internationaler Ebene beitragen. In diesem Beitrag sollen wichtige Einflussfaktoren auf das Alterungsverhalten von radioaktiven Stoffen in besonderer Form aufgezeigt und die Notwendigkeit für die Spezifikation einer Nutzungsdauer als Grundlage für die Alterungsbewertung begründet werden. Der deutsche Vorschlag für die Revision des IAEA Regelwerks zum sicheren Transport radioaktiver Stoffe (SSR-6) wird vorgestellt und erläutert. T2 - Jahrestagung des FS 2022 CY - Konstanz, Germany DA - 26.09.2022 KW - Strahlenschutz KW - Radioaktive Stoffe KW - Beförderung KW - Alterung KW - Zulassung PY - 2022 AN - OPUS4-56137 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette T1 - Safety assessment of aged metal seals N2 - With our experiments we want to simulate a load situation which can result from a cask vertical drop test. The lid can lift a little for a very short moment and that can perhaps result in a little movement of the seal, a little rotation or a little lateral movement, so that the contact section can change. The aim of the project is to learn more about the sealing efficiency after the seal is compressed again. What we know from former component tests with non-aged seals is, that the leakage rate measured after one or more decompression /compression cycles with seal movement becomes significant higher. And this result is considered for specification of design leakage rates for release calculation in safety cases. In the recent years we all have learned more about the significant influence of temperature and time on seal behavior and so the plan was to do similar experiments with aged seals, just to get an idea about seal behavior and achievable leakage rates. What we did in detail is: We compressed Helicoflex-seals of both design types, with Aluminum and Silver outer jackets, in testflanges and aged them in an oven at a temperature of 125°C for 3 months to produce seal properties comparable with properties after several years use at more typical operating temperatures between 90 and 100°C. After this ageing procedure we opened the flanges completely, moved the seal a little to vary the contact area and compressed the flanges again. What we measured during all compression and decompression cycles was the load, the deformation and -as long as possible- the leakage rates. T2 - Workshop IRSN/BAM CY - Cadarache, France DA - 12.10.2022 KW - Transport KW - Radioactive KW - Seal behavior KW - Ageing PY - 2022 AN - OPUS4-56141 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Jan T1 - Anforderungen an Ladeabteile für EX/III-Fahrzeuge N2 - Durchführung experimenteller Untersuchungen bezüglich der technischen und betrieblichen Anforderungen an Ladeabteile von EX/III-Fahrzeugen (9.3.4.2 ADR) Die derzeitigen Explosivstoffschutz-Anforderungen des Regelwerks ADR basieren auf einem überholten Stand der Technik. Die Unklarheiten führen bei den Ausrüstern und Betreibern der Gefahrgutfahrzeuge zu Unsicherheiten mit existenziellen Risiken und Kosten. Um eine Überarbeitung der ergänzenden Vorschriften für EX/III-Fahrzeuge zur Beförderung von explosiven Stoffen und Gegenständen der Klasse 1 in Versandstücken voranzutreiben, ist deshalb eine Untersuchung der Gefahren erforderlich, denen explosive Stoffe und Gegenstände während der Beförderung ausgesetzt sind. Hierzu werden auf Grundlage der heutigen Vorschriften bestehende konstruktive Lösungen untersucht und deren Wirksamkeit gegenüber einer typischen Wärmebelastung von außen festgestellt. Erforderlich dafür ist zunächst die Charakterisierung der Wärmeeinträge durch Kalorimeterversuche mit typischen Unfallbelastungen. Daraus abzuleiten sind dann idealisierte Belastungsszenarien, welche als Voraussetzung für eine Normungsarbeit angesehen werden sollen. Im letzten Schritt soll ein Textentwurf für die Erneuerung der bestehenden Vorschriften des ADR verfasst und im Anschluss international abgestimmt werden. T2 - IAA Transportation CY - Hannover, Germany DA - 19.09.2024 KW - EX/III KW - Gefahrgut KW - ADR KW - Transport KW - Brand PY - 2024 AN - OPUS4-61632 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Jan T1 - Anforderungen an Ladeabteile für EX/III-Fahrzeuge N2 - Die derzeitigen Explosivstoffschutz-Anforderungen des Regelwerks ADR basieren auf einem überholten Stand der Technik. Die Unklarheiten führen bei den Ausrüstern und Betreibern der Gefahrgutfahrzeuge zu Unsicherheiten mit existenziellen Risiken und Kosten. Um eine Überarbeitung der ergänzenden Vorschriften für EX/III-Fahrzeuge zur Beförderung von explosiven Stoffen und Gegenständen der Klasse 1 in Versandstücken voranzutreiben, ist deshalb eine Untersuchung der Gefahren erforderlich, denen explosive Stoffe und Gegenstände während der Beförderung ausgesetzt sind. Hierzu werden auf Grundlage der heutigen Vorschriften bestehende konstruktive Lösungen untersucht und deren Wirksamkeit gegenüber einer typischen Wärmebelastung von außen festgestellt. Erforderlich dafür ist zunächst die Charakterisierung der Wärmeeinträge durch Kalorimeterversuche mit typischen Unfallbelastungen. Daraus abzuleiten sind dann idealisierte Belastungsszenarien, welche als Voraussetzung für eine Normungsarbeit angesehen werden sollen. Im letzten Schritt soll ein Textentwurf für die Erneuerung der bestehenden Vorschriften des ADR verfasst und im Anschluss international abgestimmt werden. T2 - Gefahrgutkongress IHK Rostock CY - Rostock, Germany DA - 14.11.2024 KW - EX/III KW - Gefahrgut KW - ADR KW - Transport KW - Brand PY - 2024 AN - OPUS4-61639 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Jan T1 - Requirements for loading compartments for EX/III vehicles N2 - The current explosives protection requirements of the ADR regulations are based on an outdated state of the art. The lack of clarity leads to uncertainties with existential risks and costs for equipment suppliers and operators of dangerous goods vehicles. In order to promote a revision of the supplementary regulations for EX/III vehicles for the transportation of explosive substances and articles of Class 1 in packages, it is therefore necessary to examine the hazards to which explosive substances and articles are exposed during transportation. To this end, existing design solutions will be examined on the basis of current regulations and their effectiveness against a typical external heat load will be determined. The first step is to characterize the heat input by means of calorimeter tests with typical accident loads. Idealized load scenarios are then to be derived from this, which are to be regarded as a prerequisite for standardization work. In the final step, a draft text for the renewal of the existing ADR regulations is to be drawn up and then coordinated internationally. T2 - UNECE Working Party on Transport of Dangerous Goods By Road WP.15 CY - Geneva, Switzerland DA - 05.11.2024 KW - EX/III KW - Dangerous Goods KW - ADR KW - Transport KW - Fire PY - 2024 AN - OPUS4-61640 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Tightness Verification Procedures of welded Lids for Encapsulations for Damaged Spent Nuclear Fuel in the Design Approval Process of Dual-Purpose Cask N2 - Damaged spent nuclear fuel (DSNF) can be loaded in Germany in dual-purpose casks (DPC) for transport and interim storage. Therefore, special encapsulations are needed to guarantee a safe handling and a reliable tight closure. These encapsulations must be durable and leak-tight for a possible long interim storage term and the transport thereafter. Because components inside the package containment like these special encapsulations are not accessible within periodical inspections of the DPC. Due to the general design of DPCs for standard fuel assemblies, specific requirements needed to be considered for the design of the special encapsulations for DSNF to ensure the loading in existing package designs. Especially the content of the encapsulations with damaged spent nuclear fuel must be avoided to enter in the inner space of the DPC, due to the possible higher amount of corrosive and radioactive material as well as greater quantities of water, which can be trapped in defect fuel rods. The main difference of the e T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Tightness verification KW - Weld seams KW - Drop tests KW - Encapsulations for damaged spent nuclear fuel KW - Helium leak tests PY - 2024 AN - OPUS4-61353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Feldkamp, Martin A1 - Gleim, Tobias A1 - Musolff, Andre A1 - Werner, Jan A1 - Wille, Frank T1 - Enhancement of the BAM Fire Test Stand for Testing a Large Transport Package for Radioactive Materials N2 - Packages for the transport of spent nuclear fuel are designed to endure severe accidents. To obtain approval, these transport packages must adhere to the specification-based criteria of the international transport regulations SSR-6 of the International Atomic Energy Agency (IAEA). To ensure compliance with these requirements, specific mechanical and thermal tests need to be addressed with respect to the package type. Typically, SSR-6 prescribes a mechanical test followed by a thermal fire test as part of different testing scenarios. To approve the latter test of the sequence, BAM performs calorimeter tests in advance with so-called fire reference packages for characterizing the actual fire and its impact on the package to be tested. Packages are designed with different geometry sizes depending on their purpose. For previous tests, the implemented test setups in the fire test stand were sufficiently dimensioned and could cover all requirements in this respect. However, to cover additional testing needs in the future, BAM is expanding the test setup for the purpose of testing significantly larger packages. In previous test setups one ring burner for propane surrounding the test specimen was sufficient. The limiting size in this configuration was the design height of the transport package to be tested. According to the thermal test of the IAEA-Regulations [1], a 30-minute fully engulfing 800°C pool fire or an equally severe fire, e.g., propane gas fire, must be applied to the transport package. Possible adjustments such as nozzle cross-section and propane mass flow can be adjusted to a certain extent. Further modifications, to cover significantly higher and larger packages all-around with a fully engulfing fire, must be accomplished with an additional, second burner ring. Both burner rings had the same dimensions and were mounted on top of each other at different heights to create a significantly larger volume of fire that completely engulfs the package including its impact limiter. To meet the IAEA regulatory boundary conditions, the enhanced fire test stand with the second burner ring is tested with a large fire reference package and will then be used for real-size transport packages after all parameters are successfully met. This fire reference package represents the external geometry of a generic transport cask for radioactive material and is equipped with numerous temperature sensors to record temperature curves at the interior wall surfaces. T2 - RAMTrans 2024 CY - London, United Kingdom DA - 14.05.2024 KW - Fire testing KW - Full-scale KW - Transport package PY - 2024 SP - 1 EP - 7 AN - OPUS4-60253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Enhancement of the bam fire test stand for testing a large transport package for radioactive materials N2 - Packages for the transport of spent nuclear fuel are designed to endure severe accidents. To obtain approval, these transport packages must adhere to the specification-based criteria of the international transport regulations SSR-6 of the International Atomic Energy Agency (IAEA). To ensure compliance with these requirements, specific mechanical and thermal tests need to be addressed with respect to the package type. Typically, SSR-6 prescribes a mechanical test followed by a thermal fire test as part of different testing scenarios. To approve the latter test of the sequence, BAM performs calorimeter tests in advance with so-called fire reference packages for characterizing the actual fire and its impact on the package to be tested. Packages are designed with different geometry sizes depending on their purpose. For previous tests, the implemented test setups in the fire test stand were sufficiently dimensioned and could cover all requirements in this respect. However, to cover additional testing needs in the future, BAM is expanding the test setup for the purpose of testing significantly larger packages. In previous test setups one ring burner for propane surrounding the test specimen was sufficient. The limiting size in this configuration was the design height of the transport package to be tested. According to the thermal test of the IAEA-Regulations [1], a 30-minute fully engulfing 800°C pool fire or an equally severe fire, e.g., propane gas fire, must be applied to the transport package. Possible adjustments such as nozzle cross-section and propane mass flow can be adjusted to a certain extent. Further modifications, to cover significantly higher and larger packages all-around with a fully engulfing fire, must be accomplished with an additional, second burner ring. Both burner rings had the same dimensions and were mounted on top of each other at different heights to create a significantly larger volume of fire that completely engulfs the package including its impact limiter. To meet the IAEA regulatory boundary conditions, the enhanced fire test stand with the second burner ring is tested with a large fire reference package and will then be used for real-size transport packages after all parameters are successfully met. This fire reference package represents the external geometry of a generic transport cask for radioactive material and is equipped with numerous temperature sensors to record temperature curves at the interior wall surfaces. T2 - RAMTrans 2024 CY - London, United Kingdom DA - 14.05.2024 KW - Fire testing KW - Full-scale KW - Transport package PY - 2024 AN - OPUS4-60255 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Musolff, André A1 - Werner, Jan A1 - Wille, Frank T1 - Enhancement of Fire Test Stand Performance at Test Site of BAM: Installation and Evaluation of an Augmented System with a Fire Reference Package N2 - Packages for the transport of radioactive material are designed to en-dure severe accidents. Packages for the transportation of radioactive material must demonstrate that the package can withstand certain prescribed tests from the IAEA Regulations [1]. In addition to mechanical tests, a thermal test in form of a fire test must be carried out. As packages to be tested at BAM are signifi-cantly larger than previous package designs, BAM has expanded an existing fire test stand. A modular concept is chosen, which means that the arrangement of the burner nozzles can be adapted to the test specimen. The dimensions of the burner rings, the type, the orientation and the number of burner nozzles can be varied depending on the test specimen. In addition, various pumps can be used to set the corresponding mass flow. With the help of a calorimeter test, the fire test stand can be qualified for a specific size of packages regarding the boundary conditions of the IAEA Regulations [1]. Due to the typically wood filled impact limiters in German package designs, a fire test is necessary, as experiments have shown that possible openings that occurred during a mechanical test contributed to the igni-tion of the wood filled impact limiters within the prescribed 30 minutes of the IAEA Regulations [1]. From a series of experiments, two experiments are pre-sented to show the possibilities to obtain different temperatures and temperature rates in the test specimen. In addition to sensor data, the heat flux into the package is calculated to verify that the IAEA boundary conditions are satisfied. In addition to the temperature data, other data such as wind speed and wind direction are also recorded to explain subsequent effects in the measurement data in a comprehen-sible manner. T2 - Wood & Fire Safety 2024 CY - Strbske Pleso, Slowakei DA - 13.05.2024 KW - IAEA Regu-lations KW - Fire Test Stand KW - Accident Scenario KW - Fire Qualification PY - 2024 UR - https://link.springer.com/book/9783031591761 SN - 978-3-031-59176-1 SN - 978-3-031-59179-2 SN - 978-3-031-59177-8 DO - https://doi.org/10.1007/978-3-031-59177-8_22 VL - 1 SP - 189 EP - 197 PB - Springer Cham AN - OPUS4-60101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Enhancement of Fire Test Stand Performance at Test Site of BAM: Installation and Evaluation of an Augmented System with a Fire Reference Package N2 - Packages for the transport of radioactive material are designed to en-dure severe accidents. Packages for the transportation of radioactive material must demonstrate that the package can withstand certain prescribed tests from the IAEA Regulations [1]. In addition to mechanical tests, a thermal test in form of a fire test must be carried out. As packages to be tested at BAM are signifi-cantly larger than previous package designs, BAM has expanded an existing fire test stand. A modular concept is chosen, which means that the arrangement of the burner nozzles can be adapted to the test specimen. The dimensions of the burner rings, the type, the orientation and the number of burner nozzles can be varied depending on the test specimen. In addition, various pumps can be used to set the corresponding mass flow. With the help of a calorimeter test, the fire test stand can be qualified for a specific size of packages regarding the boundary conditions of the IAEA Regulations [1]. Due to the typically wood filled impact limiters in German package designs, a fire test is necessary, as experiments have shown that possible openings that occurred during a mechanical test contributed to the igni-tion of the wood filled impact limiters within the prescribed 30 minutes of the IAEA Regulations [1]. From a series of experiments, two experiments are pre-sented to show the possibilities to obtain different temperatures and temperature rates in the test specimen. In addition to sensor data, the heat flux into the package is calculated to verify that the IAEA boundary conditions are satisfied. In addition to the temperature data, other data such as wind speed and wind direction are also recorded to explain subsequent effects in the measurement data in a comprehen-sible manner. T2 - Wood & Fire Safety 2024 CY - Štrbské Pleso, Slovakia DA - 13.05.2024 KW - Fire Test Stand KW - Accident Scenario KW - Fire Qualification KW - IAEA Regu-lations PY - 2024 UR - https://link.springer.com/book/9783031591761 AN - OPUS4-60104 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Neumeyer, Tino A1 - Ballheimer, Viktor A1 - Wille, Frank T1 - Investigations of Aged Metal Seals for Transport Package Safety Assessment N2 - Acceptable limits for activity release from transport casks for high-level radioactive material specified in the IAEA regulations must be kept by the integrity of cask body and the cask sealing system. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. The specification of conservative package design leakage rates is one of the most important aspects in assessment. Metal seals of the Helicoflex® Type are usually used to ensure the required package tightness for both, storage, and transport of the cask before and after storage. Due to the long-term use the seal behavior is influenced by temperature and time. The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport specified in the regulations can have a significant effect on the leak tightness of the sealing system. Whereas the safety for application of new, non- aged Helicoflex® seals is verified sufficiently, there are still technical data gaps concerning the efficiency of aged Helicoflex® seals. BAM performed experiments to learn more about the sealing efficiency of aged Helicoflex® seals with Aluminum and Silver outer jackets. The seals were compressed in test-flanges and for artificial ageing the complete flange systems were stored in an oven for several month at a high temperature. After this ageing procedure the flanges were opened completely, the seals were moved a little to vary the contact area, and the flanges were compressed again. During the compression and decompression tests after the aging, load-deformation characteristics of the seals, and leakage rates were measured. With these tests a load situation was simulated, which can occur in the regulatory drop test of the cask: Under high impact loads the bolted lid can lift a little for a short moment, allowing a little movement of the seal, so that the contact area can change before compressing again. Details about test conditions and first results will be presented in the poster. T2 - RAMTrans 2024, 12th Internatiopnal Conference on the Transport , Storage and Disposal of Radioactive Materials CY - London, UK DA - 15.05.2024 KW - Seals KW - Ageing KW - Radioaktiv PY - 2024 AN - OPUS4-60112 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Gleim, Tobias A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Combustion Chamber Design for Encapsulated Wood-Component Testing N2 - Heavy-weight packages for the safe transport of radioactive material are equippedwith impact limiters often built ofwood-filled steel sheet structures to fulfil the requirements of the International Atomic Energy Agency (IAEA) regulations. The requirements definemechanical tests followed by a thermal test, including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Impact limiters are a package component mainly designed for the packages to withstand severe mechanical accident scenarios. In drop tests the impact limiters absorb the kinetic energy during impact of the package. The package must then - with its pre-damaged impact limiters - endure a thermal test defined precisely in the IAEA regulations as a 30-min fully engulfing 800 °C-fire. After the fire, a wood-filled impact limiter may continue to release thermal energy from an ongoing combustion process, defining relevant package temperatures. The energy flow from a possible burning impact limiter to the package is important for the safety evaluation of transport packages. To investigate the combustion behaviour of densely packed layers of spruce wood, encapsulated in pre-damaged cylindrical metal enclosures, a test set-up has been realised. The set-up consists of a combustion chamber to perform these tests under defined boundary conditions. The temperature development of the test specimens will be observed fromoutside with a thermographic imager, with HD-Cameras, and the mass loss will be measured during the entire test. Airflow conditions in the combustion chamber are analysed using Computational Fluid Dynamics (CFD) calculations in OpenFOAM. The planned combustion test setup is described. T2 - Wood & Fire Safety 2024 CY - Štrbské Pleso, Slovakia DA - 12.05.2024 KW - Fire KW - Combustion KW - Smouldering PY - 2024 SN - 978-3-031-59176-1 SN - 978-3-031-59179-2 SN - 978-3-031-59177-8 DO - https://doi.org/10.1007/978-3-031-59177-8 SP - 215 EP - 222 PB - Springer Nature Switzerland AG CY - Gewerbestrasse 11, 6330 Cham, Switzerland AN - OPUS4-60226 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Combustion Chamber Design for Encapsulated Wood-Component Testing N2 - eavy-weight packages for the safe transport of radioactive material are equippedwith impact limiters often built ofwood-filled steel sheet structures to fulfil the requirements of the International Atomic Energy Agency (IAEA) regulations. The requirements definemechanical tests followed by a thermal test, including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Impact limiters are a package component mainly designed for the packages to withstand severe mechanical accident scenarios. In drop tests the impact limiters absorb the kinetic energy during impact of the package. The package must then - with its pre-damaged impact limiters - endure a thermal test defined precisely in the IAEA regulations as a 30-min fully engulfing 800 °C-fire. After the fire, a wood-filled impact limiter may continue to release thermal energy from an ongoing combustion process, defining relevant package temperatures. The energy flow from a possible burning impact limiter to the package is important for the safety evaluation of transport packages. To investigate the combustion behaviour of densely packed layers of spruce wood, encapsulated in pre-damaged cylindrical metal enclosures, a test set-up has been realised. The set-up consists of a combustion chamber to perform these tests under defined boundary conditions. The temperature development of the test specimens will be observed fromoutside with a thermographic imager, with HD-Cameras, and the mass loss will be measured during the entire test. Airflow conditions in the combustion chamber are analysed using Computational Fluid Dynamics (CFD) calculations in OpenFOAM. The planned combustion test setup is described. T2 - Wood & Fire Safety 2024 CY - Štrbské Pleso, Slovakia DA - 12.05.2024 KW - IAEA KW - Combustion Chamber KW - Smouldering KW - Wood PY - 2024 AN - OPUS4-60227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Potential Effects of Battery and Hydrogen Fires regarding Regulatory Requirements N2 - Introduction and Necessity of the Investigation The IAEA regulations for the safe transport of radioactive material (IAEA SSR-6) define the safety requirements for different package types and consider different transport conditions. The accident conditions of transport specify different mechanical and thermal tests based on investigations of real accident scenarios. Considering the rapid development of new boundary conditions of transport such as electric mobility and the use of hydrogen as energy source for trucks and other kind of vehicles, potential effects of battery and hydrogen fires in transport accidents should be investigated. The aim is to evaluate the existing test requirements developed and derived decades ago, whether they are covering the current transport situation. This concept paper will briefly present the reasons for detailed investigations as bases for a coordinated research project under the roof of the IAEA. T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Berlin, Germany DA - 04.06.2024 KW - Fire KW - Battery KW - Hydrogen KW - IAEA Regulations PY - 2024 AN - OPUS4-60338 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian T1 - Hydrogen Fire Testing N2 - In this presentation we present a new hydrogen-based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials. The test rig will be capable of combusting hydrogen for a wide range of different burner geometries, mass flows and if necessary hydrogen blends. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and calculations must be carried out in order to develop a viable concept for hydrogen fires. In the first step of the feasibility study, the temperature, structure, and radiation of various hydrogen flames are surveyed. In future works, the results will make it possible to design burner frames that are suitable for fire reference tests in order to make comparisons with pool and propane fires used in assessment procedures today. In parallel comparative numerical simulations are conducted to model the thermal behaviour of hydrogen flames using the software package Ansys®. On the one hand, the numerical simulations support the experiments by providing an overview of numerous parameters and the measuring range; on the other hand, they will help with the design of the burner frame in future work. This paper gives an overview in the design and capabilities of the test rig. Furthermore, the results of the parameter studies show that burner geometry and mass flow provide a significant design margin for the thermal shape of the hydrogen flames. In addition, the results of the initial numerical calculations will be used to determine the necessary sensors, the positions, and their operating range. Only the optimal interaction allows a controlled system that permits user-defined hydrogen fires. T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Berlin, Germany DA - 04.06.2024 KW - Hydrogen PY - 2024 AN - OPUS4-60341 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - KI-unterstützte Begutachtung der Behältersicherheit N2 - Die BAM führt sicherheitswissenschaftliche Begutachtungen von Gefahrgutbehältern durch, die mechanische, thermische, abschirmende und transportbezogene Analysen sowie Materialbewertungen und experimentelle Prüfungen umfassen. Diese Begutachtungen basieren auf umfassenden Sicherheitsberichten und Betriebsdokumentationen, die zahlreiche verknüpfte Dokumente und Daten enthalten. Änderungen an Komponenten oder regulatorischen Vorgaben können große Auswirkungen auf den Prüfumfang haben. Das Projekt sieht vor, die Datenanalyse und -bereitstellung mittels KI-Ansätzen zu verbessern. Es sollen Methoden zur automatischen Analyse und Verknüpfung komplexer Dokumentationen entwickelt werden. Ziel ist es, die Effizienz und Sicherheit der Datenanalyse und späteren Sicherheitsbewertung zu steigern, menschliche Fehler zu minimieren und die Qualität der Sicherheitsbewertungen zu verbessern. Die Qualität der Datenbereitstellung aus Zeichnungen, Tabellen, Texten und Berechnungen ist entscheidend für die Verarbeitung digitaler Formate der Behälterdokumentation. Ein neuro-symbolischer KI-Ansatz kombiniert neuronale Netze und symbolische KI, um die komplexen Inhalte zu analysieren und zu verknüpfen, was für die spätere Sicherheitsbewertung der Gefahrgutbehälter entscheidend ist. In vortrainierten Large Language Models (LLMs) fehlen für diesen Anwendungsfall spezifische fachliche Daten zur Behältersicherheit was zu fehlerhaften Ergebnissen führen kann. Für die Datenbereitstellung und Analyse im Zuge einer Sicherheitsbewertung gilt es dieses auszuschließen. Hierzu soll die RAG-Architektur (Retrieval-Augmented Generation) im Zusammenspiel mit LLMs angewendet werden. Dieser neue Ansatz der natürlichen Sprachverarbeitung und generativen KI soll die Stärken vortrainierter Sprachmodelle mit Fachwissen und Informationen aus Datenbanken und Dokumentensammlungen kombinieren. Die generierten Ergebnisse sollen dabei zusammen mit den verwendeten Quellen bereitgestellt werden, um eine fundierte und nachvollziehbare Basis für die Sicherheitsbewertung bilden. T2 - Informationsaustausch zur verkehrsrechtlichen Aufsicht bei der Beförderung radioaktiver Stoffe CY - Bonn, Germany DA - 04.02.2025 KW - KI KW - RAG KW - LLM PY - 2025 AN - OPUS4-62538 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Experimental and Numerical Analyses for the Evaluation of Heat Fluxes of a Fire Reference Test N2 - Packages for the transport of high-level radioactive material are designed to endure severe accidents. To obtain approval, these transport packages must adhere to the specification-based criteria of the IAEA SSR-6. To ensure compliance with these requirements, specific mechanical and thermal tests need to be appointed with respect to the package type. Typically, IAEA SSR-6 prescribes mechanical tests followed by a thermal fire test as part of a cumulative test sequence. To approve the fire test, BAM uses a reference package representing the original package in its outer geometry for characterizing the actual fire and its impact on the package. This serves a dual purpose: it allows the precise adjustment of experimental parameters for the package design to be approved, and it provides input parameters for thermomechanical simulations, cf. With the help of this methodology for characterizing boundary conditions of the package, temperature evolutions within the reference package can be studied in a Finite-Element Analyses (FEA). This helps to compare the experiments with the numerical simulations on the case of the reference package, but also serves at the same time for preliminary simulations with the package design to be approved. The thermal test consists of a 30-minute fully engulfing 800°C pool fire or an equally severe fire, e.g. a propane gas fire. The fire reference test is performed prior to the regulatory fire test with the package design to be approved. The fire reference package in the described case is a closed sheet 316L steel cylinder with a wall thickness of 10 mm, a length of 182 mm, and a diameter of 102 mm. The package was instrumented with thermocouples and filled with heat resistant insulating material. T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Reference Test KW - Experimental KW - Numerical KW - Heat Flux PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 8 AN - OPUS4-60848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian A1 - Gleim, Tobias A1 - Wille, Frank T1 - Experimental and Numerical Analyses for the Evaluation of Hydrogen as an Energy Source for Thermal Testing of Transport Packages of Radioactive Material N2 - In this paper we present a new hydrogen-based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials. The test rig will be capable of combusting hydrogen for a wide range of different burner geometries, mass flows and if necessary hydrogen blends. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and calculations must be carried out in order to develop a viable concept for hydrogen fires. In the first step of the feasibility study, the temperature, structure, and radiation of various hydrogen flames are surveyed. In future works, the results will make it possible to design burner frames that are suitable for fire reference tests in order to make comparisons with pool and propane fires used in assessment procedures today. In parallel comparative numerical simulations are conducted to model the thermal behaviour of hydrogen flames using the software package Ansys®. On the one hand, the numerical simulations support the experiments by providing an overview of numerous parameters and the measuring range; on the other hand, they will help with the design of the burner frame in future work. This paper gives an overview in the design and capabilities of the test rig. Furthermore, the results of the parameter studies show that burner geometry and mass flow provide a significant design margin for the thermal shape of the hydrogen flames. In addition, the results of the initial numerical calculations will be used to determine the necessary sensors, the positions, and their operating range. Only the optimal interaction allows a controlled system that permits user-defined hydrogen fires. T2 - PVP2024, Pressure Vessels & Piping Conference CY - Bellevue, Washington USA DA - 29.07.2024 KW - Hydrogen KW - Fire KW - Computational Fluid Dynamics (CFD) KW - IAEA fire test KW - Burner PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 9 AN - OPUS4-60852 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Lars A1 - Scheidemann, Robert A1 - Neumeyer, Tino A1 - Komann, Steffen A1 - Wille, Frank T1 - Tightness Verification Procedures of Welded Lids for Encapsulations for Damaged Spent Nuclear Fuel in the Design Approval Process of Dual-Purpose Cask (DPC) N2 - Damaged spent nuclear fuel (DSNF) can be loaded in Germany in dual-purpose casks (DPC) for transport and interim storage. Therefore, special encapsulations are needed to guarantee a safe handling and a reliable tight closure. These encapsulations must be durable and leak-tight for a possible long interim storage term and the transport thereafter. Because components inside the package containment like these special encapsulations are not accessible within periodical inspections of the DPC. Due to the general design of DPCs for standard fuel assemblies, specific requirements needed to be considered for the design of the special encapsulations for DSNF to ensure the loading in existing package designs. Especially the content of the encapsulations with damaged spent nuclear fuel must be avoided to enter in the inner space of the DPC, due to the possible higher amount of corrosive and radioactive material as well as greater quantities of water, which can be trapped in defect fuel rods. The main difference of the encapsulations for damaged spent nuclear fuel is that they have no replaceable sealing as tightness barrier. They have a specific welded lid. Therefor the tightness needs to be shown in the design approval process for all transport conditions especially for accident conditions, where high internal impact loads can occur. As German competent authority, BAM is responsible for the safety assessment of the mechanical and thermal design, the release of radioactive material and the quality assurance aspects of manufacturing and operation. Concerning the mechanical package design BAM carried out a comprehensive safety assessment for the specific encapsulations during the package design approval process of the commonly used DPC. For the proof of tightness of the welded lid no representative standards are available. For minor loads the German KTA standards can verify the tightness of a weld seam but only for low stresses. For higher impact loads physical tests are required. These tests were performed with representative drop tests and highly sensitive leak tests. The present paper gives an overview of the applied assessments by BAM and points out the main findings of the mechanical design for the welded sealing. Both verification procedures are described, on one hand with German standards for lower loads and on the other hand with physical tests for higher impact loads. The drop tests based on complex numerical pre-calculations by the applicant which result in optimized dimensions and properties of the test specimens and representative drop heights for the drop tests. The horizontal drop orientation with a plane-parallel impact on the unyielding basement was most challenging and led to specific adaptations during preparation and conduction of the drop tests performed by BAM. With leak tests and the corresponding test evaluation, it could be finally approved that the specific welded sealing of an encapsulations for DSNF is tight for all transport conditions. T2 - ASME PVP 2024 CY - Bellevue, WA, USA DA - 28.07.2024 KW - Tightness verification KW - Weld seams KW - Drop tests KW - Encapsulations for damaged spent nuclear fuel KW - Helium leak tests PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 10 CY - New York AN - OPUS4-61351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Wille, Frank A1 - Linnemann, Konrad A1 - Ramsay, Jeff A1 - Reiche, Ingo T1 - Transport of large nuclear power plant components – new SCO-III regulations and mechanical design assessment N2 - The decommissioning or refurbishment of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, and coolant pumps, to list the major contributors. These components or objects are large in size and mass, measuring up to approximately 6 meters in diameter, up to 20 meters in length, and weighing over 400 000 kg. In many situations, the components are transported off-site to a storage, disposal or recycling/treatment facility. Previously, many large objects had to be transported under special arrangement. The latest 2018 edition of the International Atomic Energy Agency (IAEA) Regulations for the Safe Transport of Radioactive Material, No. SSR-6, incorporates regulations for the shipment of contaminated, but not activated large objects as a new category of surface contaminated object, SCO-III, based on the IAEA “performance package” concept. This paper provides background and practical guidance on these regulations. Additionally, first experiences with SCO-III in the approval process are presented. For SCO-III components a mechanical assessment regarding the tests specified in the transport regulations SSR-6 for demonstrating ability to withstand normal conditions of transport is required - a free drop of the package onto an unyielding target and a penetration test have to be investigated. Large components are unique objects; therefore, it is not possible to choose experimental testing as assessment method. The application of a complex numerical analysis for mechanical proof is necessary. The assessment of the loads takes place based on local stress distributions. The large nuclear components have typically been transported in an unpackaged manner, so that the external shell of the component provides the containment wall. The paper will represent the methods, which are used for the evaluation of the mechanical integrity of the object for transport approval. T2 - PVP2024, Pressure Vessels & Piping Conference CY - Bellevue, Washington USA DA - 29.07.2024 KW - Transport KW - Radioaktive Stoffe KW - Rückbau kerntechnischer Anlagen KW - Gefahrgut PY - 2024 SN - 978-0-7918-8851-3 SP - 1 EP - 4 AN - OPUS4-60829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 52, Heft 2 T3 - Amts- und Mitteilungsblatt der BAM - 2/2022 KW - Festlegungen KW - Zulassungen KW - Richtlinien KW - Anerkennungen PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-550917 SN - 0340-7551 VL - 52 IS - 2 SP - 55 EP - 158 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-55091 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Wille, Frank T1 - Dynamisches Verhalten und Überwachung des Großen Fallturms der BAM in Horstwalde N2 - Falltürme sind Bauwerke, die als Versuchsanlagen sehr speziellen, impulsartigen Belastungen ausgesetzt sind. Am Fallturm auf dem Testgelände Technische Sicherheit (TTS) der BAM wurde bei Routineinspektionen eine Abnahme der strukturellen Integrität in Form von Vorspannungsverlusten in den Bolzen der Stahlverbindungen festgestellt. Um ein Verständnis für die zugrundeliegenden Trag- und Schädigungsmechanismen zu erlangen, wurde ein umfassendes Structural Health Monitoring (SHM) System geplant und am Bauwerk installiert unter Nutzung von digitalen Bauwerksmodellen. Für die Auslegung des Überwachungssystems, insbesondere aber zur Unterstützung der Untersuchung des Schädigungsprozesses, wurden Finite-Elemente-Modelle erstellt. Um sicherzustellen, dass die FE-Modelle das reale Tragwerksverhalten mit ausreichender Genauigkeit abbilden, mussten sie jedoch in Bezug auf die gemessenen Antworten des Tragwerks kalibriert werden. Der vorliegende Beitrag beschreibt experimentelle und numerische Untersuchungen zur Identifizierung des strukturellen Systems des Stahlrohrgitterturms in Vorbereitung einer Überwachungskampagne. Die Auswertung von gemessenen Schwingungen unter ambienter Anregung ermöglichte die Identifizierung der Eigenfrequenzen mehrerer globaler Schwingungsmoden des Fallturms. Zur Modellvalidierung wurde zunächst eine Sensitivitätsanalyse durchgeführt, um die Parameter mit dem größten Einfluss zu ermitteln. Anschließend wurde ein evolutionärer Algorithmus (EA) zur Optimierung nach dem Prinzip der Minimierung der Differenzen zwischen gemessenen und simulierten charakteristischen Antworten eingesetzt. Das aktualisierte Modell wurde schließlich an der dynamischen Reaktion der Turmstruktur infolge einer realen Falltest-induzierten Stoßbelastung validiert. Die Ergebnisse zeigten eine gute Übereinstimmung zwischen numerischen und experimentellen Ergebnissen. N2 - Drop test towers are structures subjected to very specific dynamic loadings. At the drop test tower at the Test Site Technical Safety (TTS) of BAM routine inspections revealed a decline of structural integrity in form of loss of pretension in bolts of structural steel connections. To get an understanding about the underlying damage mechanisms as well as to assure the structural safety in operation, a multifaceted Structural Health Monitoring (SHM) system was planned and installed at the structure with the help of digital models. For planning the monitoring system but especially for supporting the investigation of the damaging process finite element models are deployed. Though, to ensure the capability of the FE model to reproduce the real structural behavior in sufficient accuracy, it needs to be calibrated in respect to measured responses of the structure. The present contribution describes experimental and numerical investigations to identify the structural system of the steel tube lattice tower in preparation of the monitoring campaign. An ambient vibration test allowed the identification of the natural frequencies of several global vibrational modes of the drop test tower. For model updating first a sensitivity analysis is applied to identify the most influencing parameter. In succession a genetic algorithm was applied for optimization in the sense of minimization of the difference between measured and simulated characteristic responses. The updated model is finally validated on the dynamic response of the tower structure to a real drop test induced impact loading. The results showed a good agreement between numerical and experimental results though the robustness of the simulation should be improved by more sophisticated numerical modelling. T2 - 7. VDI-Fachtagung Baudynamik CY - Würzburg, Germany DA - 27.04.2022 KW - Großer Fallturm Horstwalde KW - Structural Health Monitoring KW - Belastungsversuch KW - Modalanalyse KW - Schwingungsdynamik KW - Finite Elemente Simulation PY - 2022 SN - 978-3-18-092379-6 SN - 978-3-18-102379-2 DO - https://doi.org/10.51202/9783181023792-265 SN - 0083-5560 VL - 2379 SP - 265 EP - 284 PB - VDI-Verlag CY - Düsseldorf AN - OPUS4-55472 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rolle, Annette A1 - Neumeyer, Tino T1 - Prüfung und Zulassung von radioaktiven Stoffen in besonderer Form N2 - Radioaktive Stoffe in besonderer Form (SFRM) sind nicht dispergierbare feste radioaktive Stoffe oder dichte Kapseln, die radioaktive Stoffe enthalten /1/. SFRM sind eine Kategorie innerhalb der verkehrsrechtlichen Vorschriften. Für die Beförderung zu Anwendern in der Industrie, Medizin und Forschung werden umschlossene radioaktive Stoffe (Strahler) gemäß ihrem aktivitätsabhängigen Gefahrenpotenzial verpackt. Strahler mit einer hohen Aktivität (> A2) erfordern entsprechend der verkehrsrechtlichen Vorschriften eine Beförderung in Typ B (U) Versandstücken, die als unfallsicher gelten. Alternativ besteht bis zu einer Aktivität < A1 die Möglichkeit der Beförderung in nicht unfallsicheren Typ A Versandstücken, wenn die Strahler nachweislich unfallsicher ausgelegt sind und eine Zulassung als SFRM vorliegt. Die Bundesanstalt für Materialforschung und –prüfung (BAM) ist gemäß GGVSEB §8 (2) /2/ in Deutschland die zuständige Behörde für die Prüfung und Zulassung radioaktiver Stoffe in besonderer Form. KW - Zulassung KW - Radioaktiv KW - Beförderung KW - Strahlenschutz PY - 2020 SN - 0947-434 X IS - 1 SP - 14 EP - 16 PB - TÜV Media CY - Köln AN - OPUS4-50763 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf A1 - Hille, Falk A1 - Said, Samir A1 - Sterthaus, Jens A1 - Müller, Karsten A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Paffenholz, J.-A. A1 - Baeßler, Matthias ED - Papadrakakis, M. ED - Fragiadakis, M. ED - Papadimitriou, C. T1 - Implementing a Structural Health Monitoring system using digital models of the BAM large drop test facility in Horstwalde N2 - At the Bundesanstalt für Materialforschung und -prüfung (BAM) full scale specimens for nuclear transport and storage containers (casks) are tested for their structural integrity in a series of drop tests on the Test Site Technical Safety in Horstwalde, 50 km south of Berlin. These drop tests cause a major stress not only on the casks, but also on the steel tower structure of the test facility, itself. The load pattern makes the structure very interesting for detailed investigation. The focus of the monitoring lies on the bolted joints of the flange connections that are a typical connection for cylindrical elements if welding is technical or economical unfavorable. The definition of the monitoring takes was done by investigating the existing documents and inspection results accompanied by building an initial digital representation of the structure, consisting of two finite element (FE) models and a geometrical 3D point cloud representation. As a first step the structures behavior during static and dynamic loading was analyzed using measurement data and an updated numerical FE Model. The idea behind is to use models for a digital planning and operation/evaluation of the structural health monitoring. A static FE simulation and a dynamic FE simulation are generated, to investigate how the structure behaves under the load conditions. T2 - XI International Conference on Structural Dynamics (EuroDyn 2020) CY - Online meeting DA - 23.11.2020 KW - Structural Health Monitoring KW - Drop Tests KW - System Identification KW - Digital Models KW - BIM PY - 2020 UR - https://generalconferencefiles.s3-eu-west-1.amazonaws.com/eurodyn_2020_ebook_procedings_vol1.pdf SN - 978-618-85072-0-3 VL - 1 SP - 1293 EP - 1304 PB - Institute of Structural Analysis and Antiseismic Research CY - Athen AN - OPUS4-51592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf T1 - Structural Health Monitoring am Großen Fallturm der BAM N2 - In diesem Beitrag wird die Structural Health Monitoring Kampagne am Großen Fallturm der BAM vorgestellt. T2 - Seminar "Zerstörungsfreie Prüfung" CY - Online meeting DA - 13.01.2022 KW - Belastungsversuch KW - Großer Fallturm Horstwalde KW - Schwingungsdynamik KW - Modalanalyse PY - 2022 AN - OPUS4-55478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk T1 - Structural Health Monitoring am Großen Fallturm der BAM N2 - Am Fallturm auf dem Testgelände Technische Sicherheit (TTS) der BAM wurden bei Inspektionen Vorspannungsverluste in den Bolzen der Stahlverbindungen festgestellt. Um ein Verständnis für die zugrundeliegenden Trag- und Schädigungsmechanismen zu erlangen und um den Zustand der vorgespannten Schraubverbindungen langzeitlich zu überwachen, wurde am Fallturm ein Structural Health Monitoring (SHM) System installiert. Für die Auslegung des Monitoringsystems sowie zur Unterstützung der Untersuchung des Schädigungsprozesses wurde ein numerisches Modell erstellt und in Bezug auf die gemessenen Antworten des Tragwerks kalibriert. Im Vortrag werden die experimentellen und numerischen Untersuchungen zur Systemidentifikation des Stahlrohrgitterturms als auch die Überwachungskampagne mit dem eingesetzten Monitoringsystem sowie die Messergebnisse und deren Bewertung vorgestellt. T2 - Seminar "Zerstörungsfreie Prüfung" am Lehrstuhl für Zerstörungsfreie Prüfung ,Technische Universität München CY - Online meeting DA - 13.01.2022 KW - Structural Health Monitoring KW - Schadensüberwachung KW - Schwingungsmonitoring PY - 2022 AN - OPUS4-56667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Fracture Mechanical Investigations on a Welding Seam of a Thick-Walled Transport Package N2 - Untersuchung einer Schweißnaht mit verschiedenen Codes. Vergleiche von experimentellen und numerischen Ergebnissen T2 - Technical Exchange IRSN – BAM: Transport & Storage of Packages for Radioactive Material CY - Cadarache, France DA - 13.10.2022 KW - Drop test KW - Fracture initiation KW - Transport package PY - 2022 AN - OPUS4-56055 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichardt, Adrian A1 - Komann, Steffen T1 - Experience regarding ageing management and maintenance of transport packages in Germany N2 - The presentation gives an overview about the current experiences of BAM regarding ageing management of transport packages in Germany. The concept of the BAM-GGR 023 for ageing management of transport packagings will be described. The fundamentals of BAM-GGR 023 will be shown, including the following key aspects: -the organization of an Ageing Management System (AMS), -the issue of an Ageing Management Plan (AMP), -the ageing evaluation as a part of the AMP, -the Ageing Surveillance Program (ASP) as a part of the AMP, -the Ageing Management Documentation (AMD). T2 - First Consultancy Meeting on Drafting the Safety Guide on Ageing Management and Maintenance of Radioactive Material Transport Packages CY - Vienna, Austria DA - 20.11.2023 KW - Ageing Management KW - Dual Purpose Cask KW - BAM-GGR 023 PY - 2023 AN - OPUS4-58863 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Neumann, Martin A1 - Linnemann, Konrad T1 - Full-scale drop testing with a heavy-weight package for radioactive waste N2 - Packages for the transport of radioactive materials shall fulfil the requirements of the IAEA regulations for the safe transport. The requirements define mechanical and thermal test conditions including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Different methods can be used for safety demonstration showing compliance with the regulations. The central part of a safety demonstration which is presented in this paper was a comprehensive drop test program with a full-scale model of a transport package accompanied by pre- and post-test FE analyses. Using full-scale drop test models allow the benefit that similarity and scaling issues become a significant smaller issue, additional material investigations can be limited and analyses for transferring test results to the original package design are reduced. Additionally, experience for the future serial packaging manufacturing and handling procedures can be collected in a very early state of the design approval process. The pre-test finite element analyses derived and justified the drop test program consisting of several drop sequences with different drop orientations of the specimen. The performance and the results of the drop test sequences shows the manageability and the advantage e.g., in view of the direct availability of test results for the package licensing. On the other hand, the drop test performance shows the difficulties during handling and the need for additional equipment during preparation of the specimen. The package presented was intended for the transport and storage of compacted radioactive waste from reprocessing of spent nuclear fuel assemblies - designed and applied for approval by the AGC consortium. The project ended in 2021. The package design was characterized by a cask body made of a forged thick stainless-steel shell, a bolted double lid system with metallic gaskets and wood filled shock absorbers at both ends. The total mass of the entire transport package including content was 120,000 kg, the total length was about 7000 mm and the diameter approximately 3000 mm, both measures include the shock absorbers. The paper provides an insight into the performance of a full-scale drop testing campaign within the package safety evaluation and shows some selected test results. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Full-scale KW - Drop testing KW - Package KW - Radioactive materials transport PY - 2023 SP - 1 EP - 10 AN - OPUS4-57732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Martin A1 - Gleim, Tobias A1 - Gradt, Thomas T1 - Friction coefficients for wood-wood and wood-steel high pressure contact under temperatures between -40 °C and 90 °C N2 - Wood is widely used in impact limiters of Transport casks for radioactive material. Encapsulated by an outer and inner Steel structure, spruce wood is offen applied in layers of altemating direction. The friction at the interfaces between these layers is of crucial importance for the impact and energy absorption e.g., at an accidental impact of a cask against a hard component. In order to get detailed Information for corresponding numerical calculations, in this study the friction coefficient for the combinations wood-wood and wood-steel was measured in the temperature ränge between -40 °C and 90 °C according to the relevant stress conditions for such casks. Results show decreasing friction with increasing temperature, ranging from 0.43 at -40 °C to 0.22 for 90 °C for wood-steel combinations and from 0.3 at -40 °C to 0.24 at 90 °C to for a wood-wood combination. KW - Wood KW - Friction KW - Transport cask KW - Radioactive material PY - 2023 DO - https://doi.org/10.24053/TuS-2023-0007 SN - 0724-3472 VL - 70 IS - 2 SP - 5 EP - 12 PB - expert verlag AN - OPUS4-57787 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven A1 - Reichardt, Adrian A1 - Müller, Lars A1 - Neumann, Martin A1 - Komann, Steffen A1 - Wille, Frank T1 - Introduction of the German ageing management guide for packages for transport of radioactive materials N2 - The consideration of ageing mechanisms is with integration of the new para 613A into IAEA SSR-6 (Rev. 1) now obligatory for the design of transport packages. In addition, para 809(f) requires for packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance. Para 503(e) requires that all packaging components and radioactive contents have been maintained during storage in a manner that all requirements specified in IAEA SSR-6 (Rev.1) and in the applicable certificates of approval have been fulfilled. The evaluation of ageing mechanisms and their effects including monitoring are part of BAM’s authority assessment tasks related to the mechanical and thermal package design and quality assurance aspects. BAM has compiled a guideline for the implementation of ageing assessment and of the measures for ageing management of the approval procedure based on requirements of IAEA SSR-6 (Rev.1). The guideline is applicable only for packages requiring a competent authority approval. The paper aims to describe the structure of the guideline and the general approach for ageing management requirements. The type and amount of measures for ageing management depend mainly on the use of the package and on the ageing effects for the component, which result from relevant ageing mechanisms during package operation time. The implementation of measures for ageing management is divided into three levels – systemic measures, package design related measures and documentation. The systemic measures are attributed to the general management system and define the whole activities for organization of ageing management like structure, responsibilities, documentation, reports and evaluation. The package design related measures are defined in an ageing management plan (AMP). These measures shall ensure that the anticipated changes of the package design under consideration of ageing effects still complies with the design approval specification. Therefore, an ageing surveillance program (ASP) and, if necessary, a gap analysis program shall be developed. The ageing management documentation (AMD) ensures the continuous documentation of the compliance of a specific package to the approved package design, comprising mainly records resulting from operation and surveillance. T2 - PATRAM22 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-les-Pins, France DA - 11.06.2023 KW - Guide KW - Ageing KW - Mechanism KW - Package KW - Management PY - 2023 SP - 1 EP - 10 PB - World Nuclear Transport Institute (WNTI) CY - London AN - OPUS4-57770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Gröke, Carsten A1 - Neumeyer, Tino T1 - Design assessment, approval of management systems and ageing aspects of transport packages for radioactive material not requiring competent authority approval of design N2 - Most transports of radioactive materials are carried out with packages not requiring competent authority approval of design. These encompass – in accordance with the IAEA SSR-6 regulations – packages of the classification excepted, Industrial packages Type 1, 2 and 3 and Type A packages. Currently an upsurge in number and variation of these package designs can be seen in Germany, resulting from the phase out of nuclear energy in Germany as well as e. g. increased use of radioactive material for medical purposes. A design assessment regarding the package safety is required in the international IAEA SSR-6 regulations. BAM operates facilities for the performance of all regulatory tests required such as drop towers for a wide range of package masses and dimensions, fire test, leak tightness measurements and pressure test facilities. Experiences with several package types are shown. Additionally, IAEA SSR-6 requires the establishment of a management system for design, manufacture, maintenance, and repair of the packaging as well as for the preparation, consigning, loading, carriage, unloading and receipt of the package. Relevant for Germany, BAM has published guidance material on the process of management system acceptance in the technical guide BAM-GGR 016. The requirements encompass quality management plans for the manufacturing of packages including independent manufacturing surveillance and specific instructions for operation, maintenance, and repair of packagings. Examples for management system specifics and requirements are given. Since the latest edition of the IAEA SSR-6 regulations an ageing evaluation including systematic ageing management measures are required for all kind of package types. BAM is going to update the guidance material BAM-GGR 016 to support the stakeholders with relevant information to fulfil the ageing aspect for packages not requiring competent authority approval. The paper explains how the ageing aspect may be included in the safety evaluation process and the management system measures and will give an outlook for the future guidance material. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Typ KW - Radioactive material KW - Non-approved PY - 2023 SP - 1 EP - 8 AN - OPUS4-57703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven T1 - Introduction of the German Ageing Management Guide for Packages for Transport of Radioactive Materials – BAM-GGR 023 N2 - BAM-GGR 023 was published in June 2022 BAM-GGR 023 gives guidance to applicants regarding ageing management for competent authority approved package designs Ageing management with evaluation of ageing mechanisms according to para 613A of IAEA SSR-6 (Rev. 1) and their effects are part of the general management system. Essential items are: AMS (systemic-related), AMP (package design-related) and AMD (package-related) There are different requirements for organization and extent of ageing management depending on type of use There are also different requirements for ageing evaluation depending on type of use for packaging/package, classification of components and their accessibility and replaceability T2 - PATRAM22 CY - Juan-les-Pins, France DA - 11.06.2023 KW - Package KW - Ageing KW - Mechanism KW - Management KW - Guide PY - 2023 AN - OPUS4-57821 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Wille, Frank A1 - Komann, Steffen A1 - Neumann, Martin T1 - Qualification Procedure for Seal Designs for Spent Fuel Transport and Storage Cask Containments N2 - The seal is a key component of the containment and closure system of transport and storage casks for radioactive material. It is a major contributor to ensuring compliance with the acceptable limits for activity release according to IAEA regulations. The requirements for a safe seal performance are high, accordingly. Every new seal design intended for use in the containment of a transport cask for radioactive material passes a qualification process in Germany. The qualification process is supervised by BAM as German competent authority for mechanical, thermal and containment assessment of packages requiring design approval. The closure system including the seal shall be able to withstand the corrosive, mechanical and thermal loads associated with routine, normal and accident conditions of transport according to the IAEA regulations without losing the required sealing function. Metal seals of the Helicoflex® type are often used to ensure required package leak tightness for both storage and transport, including transport after long term interim storage. The poster will provide an overview of requirements during a seal qualification process on the example of a Helicoflex® type metal seal. T2 - 21st International Symposium on the Packaging and Transportation of Radioactive Materials, PATRAM 2025 CY - San Antonio, Texas , US DA - 27.07.2025 KW - Spent fuel transport KW - Seals KW - Radioactive KW - Containment PY - 2025 SP - 1 EP - 5 AN - OPUS4-63911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette T1 - Qualification Procedure for Seal Designs for Spent Fuel Transport and Storage Cask Containments N2 - The seal is a key component of the containment and closure system of transport and storage casks for radioactive material. It is a major contributor to ensuring compliance with the acceptable limits for activity release according to IAEA regulations. The requirements for a safe seal performance are high, accordingly. Every new seal design intended for use in the containment of a transport cask for radioactive material passes a qualification process in Germany. The qualification process is supervised by BAM as German competent authority for mechanical, thermal and containment assessment of packages requiring design approval. The closure system including the seal shall be able to withstand the corrosive, mechanical and thermal loads associated with routine, normal and accident conditions of transport according to the IAEA regulations without losing the required sealing function. Metal seals of the Helicoflex® type are often used to ensure required package leak tightness for both storage and transport, including transport after long term interim storage. The poster will provide an overview of requirements during a seal qualification process on the example of a Helicoflex® type metal seal. T2 - 21stInternational Symposium on the Packaging and Transportation of Radioactive Materials, PATRAM 2025 CY - San Antonio, Texas , US DA - 27.07.2025 KW - Spent fuel transport KW - Seals KW - Raqdioactive KW - Containment PY - 2025 AN - OPUS4-63909 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Monavari, Mehran A1 - Bertovic, Marija A1 - Wille, Frank T1 - AI-driven Documentation Analysis for Safety Assessment of Packages with Hazardous Goods N2 - Transport packages for radioactive material require, dependent on type und quantity of the radioactive material, a regulatory approval. Safety assessments shall be conducted in compliance with the IAEA regulations and documented in a comprehensive package design safety report to obtain approval from authority. This comprehensive safety report evaluates a broad range of requirements from the regulations, including physical specifications, control measures, and testing assessments. Additionally, it encompasses supporting documents such as specifications, plans in a variety of complex documents. Safety and manufacturing reports contain multiple interconnected sub-reports covering various topics. Changes, such as component modifications, material property updates, standards, or regulatory revisions, often impact multiple sections of the safety analysis reports, making even minor adjustments complex and time-consuming. Each transport package has unique constraints, making every safety report distinct, despite following the same regulatory framework. This project aims to enhance data analysis and processing through AI-based approaches [4]. Automated methods for analysing and interlinking documentation will improve efficiency, accuracy, and consistency while reducing human error in safety assessments. A key challenge is that pre-trained Large Language Models (LLMs) lack domain-specific data on packaging safety, potentially leading to inaccurate results. To mitigate this, the project applies Retrieval-Augmented Generation (RAG) in conjunction with LLMs. This approach integrates the strengths of pre-trained models with expert knowledge from databases and document repositories, ensuring accurate, well-founded, and transparent assessments. Beyond technical challenges, human factors must be considered early. New technologies often trigger resistance, if not introduced properly. Furthermore, long-term AI-reliance may lead to loss of expertise needed to solve complex problems. User-centred approach ensures effective implementation and lasting viability. This study evaluates the feasibility of using LLMs [2] and RAG [1, 3] for regulatory compliance in radioactive material transport. By analysing current documentation workflows, we assess how AI-driven tools can interpret complex safety reports and identify critical dependencies. Furthermore, we highlight the necessity of robust data governance, confidentiality measures, and AI reliability in this highly regulated domain. T2 - KONTEC 2025 CY - Dresden, Germany DA - 17.09.2025 KW - AI-driven KW - QI-Digital KW - Retrieval-Augmented Generation KW - Large Language Model PY - 2025 SP - 1 EP - 9 PB - Kontec Gesellschaft für technische Kommunikation GmbH CY - Dresden AN - OPUS4-64154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - KI-unterstützte Dokumentenanalyse für die Sicherheitsbewertung von Transportbehältern für Gefahrstoffe N2 - Transport packages for radioactive material require, dependent on type und quantity of the radioactive material, a regulatory approval. Safety assessments shall be conducted in compliance with the IAEA regulations and documented in a comprehensive package design safety report to obtain approval from authority. This comprehensive safety report evaluates a broad range of requirements from the regulations, including physical specifications, control measures, and testing assessments. Additionally, it encompasses supporting documents such as specifications, plans in a variety of complex documents. Safety and manufacturing reports contain multiple interconnected sub-reports covering various topics. Changes, such as component modifications, material property updates, standards, or regulatory revisions, often impact multiple sections of the safety analysis reports, making even minor adjustments complex and time-consuming. Each transport package has unique constraints, making every safety report distinct, despite following the same regulatory framework. This project aims to enhance data analysis and processing through AI-based approaches [4]. Automated methods for analysing and interlinking documentation will improve efficiency, accuracy, and consistency while reducing human error in safety assessments. A key challenge is that pre-trained Large Language Models (LLMs) lack domain-specific data on packaging safety, potentially leading to inaccurate results. To mitigate this, the project applies Retrieval-Augmented Generation (RAG) in conjunction with LLMs. This approach integrates the strengths of pre-trained models with expert knowledge from databases and document repositories, ensuring accurate, well-founded, and transparent assessments. Beyond technical challenges, human factors must be considered early. New technologies often trigger resistance, if not introduced properly. Furthermore, long-term AI-reliance may lead to loss of expertise needed to solve complex problems. User-centred approach ensures effective implementation and lasting viability. This study evaluates the feasibility of using LLMs [2] and RAG [1, 3] for regulatory compliance in radioactive material transport. By analysing current documentation workflows, we assess how AI-driven tools can interpret complex safety reports and identify critical dependencies. Furthermore, we highlight the necessity of robust data governance, confidentiality measures, and AI reliability in this highly regulated domain. T2 - KONTEC 2025 CY - Dresden, Germany DA - 17.09.2025 KW - AI-driven KW - QI-Digital KW - Retrieval-Augmented Generation KW - Large Language Model PY - 2025 AN - OPUS4-64153 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Neumann, Martin T1 - Maßnahmen zum Qualitäts- und Alterungsmanagement nicht zulassungspflichtiger Bauarten von Versandstücken zur Beförderung radioaktiver Stoffe N2 - Die BAM-GGR 016 erläutert die Anforderungen des ADR, RID, ADN und IMDG hinsichtlich notwendiger Maßnahmen zum Qualitäts- und Alterungsmanagement bei der Auslegung, Herstellung, Prüfung, Dokumentation, Gebrauch, Wartung und Inspektion von nicht-zulassungspflichtigen Versandstücken für radioaktive Stoffe für alle Bauarten von freigestellten Versandstücken, Industrieversandstücken des Typs IP-1, IP-2 und IP-3 und Versandstücken des Typs A. KW - Radioaktive Stoffe KW - Transport KW - Beförderung KW - Nicht-zulassungspflichtig KW - Prüfpflichtig PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-595229 VL - BAM-GGR 016 SP - 1 EP - 26 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin ET - Revision 1 AN - OPUS4-59522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, O. A1 - Neumann, Martin T1 - System of Quality Assurance Measures in Manufacturing and Operation of Dual Purpose Casks for Spent Nuclear Fuel and High Level Waste in Germany N2 - German spent nuclear fuel and high level waste is stored in dry conditions in interim storage facilities until a final repository will be ready for operation in the future. Dual purpose casks are used for the packaging of the materials to ensure transportability at any time during long-term interim storage and fulfilling both requirements from interim storage as well as transport. Germany’s 2011 decision to phase out utilization of nuclear energy has led to a high demand for casks for decommissioning power plants as quickly as possible. Cask serial production will continue at a high level for the next few years. In the process, a system of quality assurance measures ensures that every cask reliably complies with design specification according the transport approval certificate and storage license. When the first casks were manufactured in Germany about 40 years ago, quality assurance was oriented towards pressure vessel and general nuclear manufacturing. The system was continuously adapted to the state of the art. In particular serial production, globalization of manufacturing and deep supplier chains had to be taken into account. The system of quality assurance measures applied today for cask manufacturing shall be presented here. The quality assurance measures can be categorized as system-related and design-related. With respect to transport regulations for example, they are independently approved and monitored by the competent authority BAM and its authorized inspection experts. The qualification of the applicant is reviewed first in the context of the design approval procedure and then periodically. The qualification of component and cask manufacturers is also checked at the start of manufacturing and then periodically. Before the start of manufacturing documents such as quality plans are pre-assessed. Manufacturing and inspection are then performed according to the pre-assessed documents. Cask manufacturing is completed by a final inspection before commissioning. Periodic inspections during operation ensure preservation of the properties specified in the approval certificate over package life time. The type and the time interval of periodic inspections depend on the use of the package. For transport after interim storage a system of specific tests and inspections is prescribed. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-les-Pins, France DA - 11.06.2023 KW - Radioactive material KW - Quality Assurance Measures KW - Dual Purpose Casks KW - Independent Surveillance PY - 2023 AN - OPUS4-57705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Wille, Frank A1 - Neumann, Martin A1 - Linnemann, Konrad ED - Baraldi, P. ED - Di Maio, F. ED - Zio, E. T1 - Safety Evaluation of a Package for Radioactive Waste by Full-Scale Drop Testing N2 - As part of the evaluation of a package for the safe transport of radioactive waste the regulations of the IAEA International Atomic Energy Agency shall be fulfilled. The regulations define requirements for the package and specify mechanical and thermal test conditions. Different methods are allowed for the test performance to demonstrate compliance with the regulations. Next to calculational approaches and the use of models of an appropriate scale, the performance of full-scale testing with prototype packages respectively full-scale models is applied. The use of full-scale models has several advantages within the complete safety assessment procedure for a transport package approval. Scaling and corresponding similarity questions don’t have to be considered, additional material investigations can be limited and analyses to transfer test results to the original package design are reduced in number and complexity. Additionally, experience for future serial design procedures can be built up during manufacturing and assembling of the test model. BAM operates different drop and fire test facilities south of Berlin, Germany. BAM has started to perform a drop test campaign with a full-scale model of 120 metric tons weight for a transport package approval procedure. The paper describes experience with test preparation, drop performance and additional analyses. The measurement concept is explained and test goals regarding the package safety assessment and evaluation of safety margins are introduced. T2 - 30th European Safety and Reliability Conference and 15th Probabilistic Safety Assessment and Management Conference (ESREL2020 PSAM15) CY - Online meeting DA - 01.11.2020 KW - Slap-down KW - Transport safety KW - Package KW - Drop test KW - Similarity KW - FEA KW - Radioactive waste PY - 2020 UR - https://www.rpsonline.com.sg/proceedings/esrel2020/html/3809.xml SN - 987-981-14-8593-0 SP - Paper 3809,1 EP - 8 PB - Research Publishing Services CY - Singapore AN - OPUS4-50981 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen T1 - Managementsystem Guide der IAEA (TS-G-1.4) N2 - Es wird der Safety Guide der IAEA für das Managementsystem für den Transport radioaktiver Stoffe vorgestellt. Des Weiteren werden die BAM-Gefahrgutregeln für das Managementsystem erläutert. T2 - Informationsaustausch zur verkehrsrechtlichen Aufsicht bei der Beförderung radioaktiver Stoffe CY - Bonn, Germany DA - 04.02.2025 KW - Radioaktive Stoffe KW - Rückbau kerntechnischer Anlagen KW - Transport KW - Gefahrgut PY - 2025 AN - OPUS4-62654 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Small modular reactor (SMR) - Prinzip und Potenzial N2 - Derzeit gewinnen Small Modular Reactors (SMR) im Bereich zwischen 30 und 300MW in der internationalen Community stark an Gewicht. Diverse Länder entwickeln diese Reaktorkonzepte und viele Länder (unter anderem die Schweiz) planen, diese einzusetzen. Dieser Vortrag beleuchtet das Prinzip und das Potenzial der SMR sowie Chancen und Risiken. T2 - Vortragsreihe am Sportgymnasium Davos CY - Davos, Switzerland DA - 06.03.2025 KW - SMR KW - Radioaktiv PY - 2025 AN - OPUS4-63434 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reichardt, Adrian T1 - Introduction of an ageing management approach for packages for the transport of radioactive materials N2 - With integration of the new para 613A into SSR-6 [1] the consideration of ageing mechanisms is now obligatory for the design of packages and their approval. In addition, para 809(f) of SSR-6 [1] requires consideration of the effects of storage on ageing mechanisms, safety analyses and operation and maintenance instructions. German competent authorities Bundesanstalt für Materialforschung und -prüfung (BAM) and Bundesamt für die Sicherheit der nuklearen Entsorgung (BASE) are considering the aspect of ageing in approval procedures. Ageing assessment is mainly focused on dual purpose casks (DPC) package designs which are long-term stored in interim storage facilities. For these package designs, the evaluation of ageing management is now mandatory for the maintenance of the package design approvals with a validity period of 5 years and beyond. The ageing management includes amongst others a gap analysis, the assessment of ageing effects and operational experiences during operation and interim storage. BAM works on the compilation of a guideline for implementation of paras 613A, 809(f) and 809(k) for packages requiring competent authority approval at the application procedure in Germany. The paper describes essential items of ageing mechanisms and will give a foresight to the ageing management evaluation by BAM. T2 - INMM & ESARDA Joint Annual Meeting CY - Online Meeting DA - 30.08.2021 KW - Ageing KW - Dual purpose casks KW - Transport of radaioactive materials KW - Ageing mechanisms KW - Interim storage KW - SSR-6 PY - 2021 AN - OPUS4-53197 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Neumann, Martin A1 - Linnemann, Konrad A1 - Komann, Steffen A1 - Wille, Frank T1 - Fracture Mechanical Analyses of a Welding Seam of a Thick-Walled Transport Package N2 - Transport packages shall satisfy various safety criteria regarding mechanical, thermal and radiation phenomena. Typical requirements focusing mechanical aspects are usually drop tests in accordance with IAEA regulations. The drop tests are usually carried out experimentally and, as an additional measure, finite element analyses (FEA) are performed. A specific part of the investigations presented is the evaluation of the welding seam connecting cask shell and cask bottom. Experimental results and FEA are presented and compared. The evaluation of the welding seam performed includes a variety of aspects. In addition to the experimental and analytical stresses determined, different standards are used to investigate a possible crack initiation. Several destructive and non-destructive tests are performed for quality assurance in the manufacturing process as well as for different input parameters. The necessary monitoring and non-destructive measurement methods to define the boundary conditions of the standards are introduced. Taking into account all required parameters, the welding seam is examined and evaluated using the failure assessment diagrams (FAD) of the respective standards. It can be shown under the given boundary conditions that considering the experimental data, the welding seam is in the context of crack initiation below the enveloping curve in the acceptable region. More critical drop tests to be conducted are proposed and need to be investigated in future work. T2 - Pressure Vessels & Piping Conference® 2022 CY - Las Vegas, NV, USA DA - 17.07.2022 KW - Transport package KW - Drop test KW - Fracture initiation PY - 2022 SP - 1 EP - 9 AN - OPUS4-55375 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Nuclear disposal - transport and storage of radioactive waste N2 - This presentation deals with transport, interim storage, and final disposal of radioactive material in Germany in the context of the University of Magdeburg course "Introduction to nuclear plant design and safety". The IAEA regulatory framework, relevant tests for ensuring safety, and transport packages are a major part of the transport aspect. Different interim storage designs are discussed as well as the current state of final repositories in Germany analyzed. Finally, a European perspective is given. T2 - Vorlesungsreihe "Introduction to nuclear plant design and safety" CY - Magdeburg, Germany DA - 13.06.2025 KW - Nuclear KW - Transport KW - Radioactive KW - Material PY - 2025 AN - OPUS4-63433 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven A1 - Reichardt, Adrian A1 - Wille, Frank A1 - Komann, Steffen A1 - Neumann, Martin T1 - Introduction of an ageing management approach for packages for the transport of radioactive materials N2 - With integration of the new para 613A into SSR-6 [1] the consideration of ageing mechanisms is now obligatory for the design of packages and their approval. In addition, para 809(f) of SSR-6 [1] requires consideration of the effects of storage on ageing mechanisms, safety analyses and operation and maintenance instructions. German competent authorities Bundesanstalt für Materialforschung und -prüfung (BAM) and Bundesamt für die Sicherheit der nuklearen Entsorgung (BASE) are considering the aspect of ageing in approval procedures. Ageing assessment is mainly focused on dual purpose casks (DPC) package designs which are long-term stored in interim storage facilities. For these package designs, the evaluation of ageing management is now mandatory for the maintenance of the package design approvals with a validity period of 5 years and beyond. The ageing management includes amongst others a gap analysis, the assessment of ageing effects and operational experiences during operation and interim storage. BAM works on the compilation of a guideline for implementation of paras 613A, 809(f) and 809(k) for packages requiring competent authority approval at the application procedure in Germany. The paper describes essential items of ageing mechanisms and will give a foresight to the ageing management evaluation by BAM. T2 - INMM & ESARDA Joint Annual Meeting CY - Online meeting DA - 30.08.2021 KW - Dual purpose casks KW - Ageing KW - SSR-6 KW - Interim storage KW - Ageing mechanisms KW - Transport of radaioactive materials PY - 2021 UR - https://www.abstractsonline.com/pp8/#!/10383/presentation/964 SP - 1 EP - 6 PB - Institute of Nuclear Materials Management (INMM) CY - Mount Laurel, NJ AN - OPUS4-53180 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Full-scale drop testing with a heavy-weight package for radioactive waste N2 - Packages for the transport of radioactive materials shall fulfil the requirements of the IAEA regulations for the safe transport. The requirements define mechanical and thermal test conditions including criteria ensuring the package design’s ability to withstand severe accidents and provide a high level of technical safety. Different methods can be used for safety demonstration showing compliance with the regulations. The central part of a safety demonstration which is presented in this paper was a comprehensive drop test program with a full-scale model of a transport package accompanied by pre- and post-test FE analyses. Using full-scale drop test models allow the benefit that similarity and scaling issues become a significant smaller issue, additional material investigations can be limited and analyses for transferring test results to the original package design are reduced. Additionally, experience for the future serial packaging manufacturing and handling procedures can be collected in a very early state of the design approval process. The pre-test finite element analyses derived and justified the drop test program consisting of several drop sequences with different drop orientations of the specimen. The performance and the results of the drop test sequences shows the manageability and the advantage e.g., in view of the direct availability of test results for the package licensing. On the other hand, the drop test performance shows the difficulties during handling and the need for additional equipment during preparation of the specimen. The package presented was intended for the transport and storage of compacted radioactive waste from reprocessing of spent nuclear fuel assemblies - designed and applied for approval by the AGC consortium. The project ended in 2021. The package design was characterized by a cask body made of a forged thick stainless-steel shell, a bolted double lid system with metallic gaskets and wood filled shock absorbers at both ends. The total mass of the entire transport package including content was 120,000 kg, the total length was about 7000 mm and the diameter approximately 3000 mm, both measures include the shock absorbers. The paper provides an insight into the performance of a full-scale drop testing campaign within the package safety evaluation and shows some selected test results. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Full-scale KW - Drop testing KW - Package KW - Radioactive waste PY - 2023 AN - OPUS4-57731 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Delfin - Statusbericht zum 4.HJM N2 - Präsentation über den Fortschritt der BAM zum Vorhaben Delfin, welches sich mit der Entwicklung und Schädigungsneigung von Composite-Wasserstoffbehältern für den Anwendungsfall KFZ beschäftigt T2 - 4. Halbjahresmeeting zum Vorhaben Delfin CY - Online meeting DA - 21.10.2020 KW - Wasserstoff KW - Impact KW - Druckbehälter PY - 2020 AN - OPUS4-51495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - A fire test stand for thermal testing of extra-large packages N2 - Packages for the transport of high-level radioactive materials are designed to withstand severe accidents. These packages must adhere to the specification-based criteria of the International Transport Regulations of the International Atomic Energy Agency (IAEA). To ensure compliance with these requirements, specific mechanical and thermal tests need to be addressed with respect to the package type. Typically, the Regulations prescribe mechanical tests followed by a thermal test as part of a cumulative test scenario. The thermal test is specified by the exposure of a test specimen for a period of 30 minutes to a thermal environment that provides a heat flux equivalent to that of a hydrocarbon fuel-air fire with an average fire temperature of at least 800 °C fully flame engulfing the test specimen. The Federal Institute for Materials Research and Testing (BAM) operates various test facilities for this purpose at their test site (TTS) near Berlin in Germany. Thermal tests for large packages are carried out in an established fire test stand that can be adapted by the test-setup to the geometric boundary conditions of a test specimen. This fire test stand is built for test specimens with masses up to 200,000 kg and geometric dimensions relating to large transport packages including their impact limiters. The test specimen is usually placed on a water-cooled support frame in the middle of the test-stand. The fire is realized by burning propane gas which is released in liquid state from an array of gas nozzles arranged in the form of a burner ring surrounding the test specimen. For particularly extra-large test specimens, two burner rings are used on top of each other and at different heights in order to firstly achieve full fire engulfment with a significantly larger volume of fire and secondly to achieve the required heat output. In advance of a regular thermal test BAM usually performs so-called fire reference tests to determine the test conditions for compliance with the IAEA requirements. These tests are performed using a generic package which corresponds to the external geometric dimensions of the test specimen used later in the approval test. Then, this reference package is exposed to a fire under defined test parameters whereas the corresponding heat input determined from the temperature changes measured is regarded as main criterion for proofing compliance with the IAEA criteria. The paper shows the experimental proof of the suitability of BAM’s fire test stand for thermal testing of extra-large packages. The heat input and fire temperatures fully meet the IAEA criteria but can also be set significantly higher for e.g. extra-regulatory testing. T2 - ASME PVP 2025 CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Package KW - Thermal testing KW - Test stand KW - Fire PY - 2025 AN - OPUS4-63893 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven A1 - Neumann, Martin A1 - Reichardt, Adrian A1 - Komann, Steffen A1 - Wille, Frank T1 - Experiences with the implementation of ageing management for packages for transport of radioactive materials in Germany N2 - The consideration of ageing mechanisms is now obligatory for the design of transport packages with integration of the para 613A into IAEA SSR-6 (Rev. 1). In addition, para 809(f) of SSR-6 (Rev. 1) requires for packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance. Para 503(e) requires that these packages have been maintained during storage in a manner that all requirements specified in SSR-6 (Rev.1) and in the applicable certificates of approval have been fulfilled. The evaluation of ageing mechanisms and their effects including monitoring are part of BAM’s authority assessment tasks related to the mechanical and thermal package design and quality assurance aspects. BAM has compiled the guideline BAM-GGR 023 for the implementation of ageing assessment and related measures into the approval procedure. The implementation of ageing management measures is obligatory in case of extension/renewal of package design approval certificates. BAM has evaluated package designs which are used only for transport as well as package designs for long term interim storage. The assessment of ageing mechanisms associated with the identification of ageing effects on components is the main part of the ageing management plan (AMP). Different approaches regarding AMP structure are introduced. Experiences and approaches about the evaluation of components for the expected package operating time are shown. We are focusing the evaluations of proofs for not accessible and not replaceable components. Operational experiences for these package designs are available and should be considered in the ageing evaluation. Corresponding measures for package monitoring are to be derived based on these results. The measures for monitoring shall be fixed in the Ageing Surveillance Program (ASP) to maintain a specification conform package for the transport on public routes. We show exemplary how results from ageing evaluation during the approval procedure are transferred into the ASP. T2 - PATRAM 2025 CY - San Antonio, Texas , US DA - 27.07.2025 KW - RAM KW - Ageing management KW - Radioactive material KW - Transport PY - 2025 SP - 1 EP - 8 PB - INMM CY - Washington D.C. AN - OPUS4-63987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Feldkamp, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Conclusions from the first return campaign of vitrified High-Level Waste on sea going vessels from the competent authority N2 - Germany has to take back vitrified waste from the reprocessing plants in France and Great Britain. The waste resulted from decades of transporting spent fuel for reprocessing to La Hague and Sellafield. The return campaign from France was concluded in 2024 with the transport of five CASTOR® HAW28M casks to the interim storage facility in Philippsburg in southern Germany. The return of waste from Sellafield comprises three campaigns and a total of 20 CASTOR® HAW28M casks. The first campaign was performed in 2020, consisting of six CASTOR® HAW28M casks, while the second campaign was performed in March 2025, consisting of seven CASTOR® HAW28M casks. The casks were transported by rail from Sellafield to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. The third campaign is expected to be performed during 2026. BAM as part of the German competent authority system was among others involved in the assessment of the sea transport. BAM required for the first transport, among others, an assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of the IMDG code and its supplement the INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - PATRAM 2025 CY - San Antonio, Texas, USA DA - 27.07.2025 KW - RAM KW - Transport KW - Radioactive material KW - Sea PY - 2025 SP - 1 EP - 8 PB - INMM CY - Washington D.C. AN - OPUS4-63984 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Experiences with the implementation of ageing management for packages for transport of radioactive materials in Germany N2 - The consideration of ageing mechanisms is now obligatory for the design of transport packages with integration of the para 613A into IAEA SSR-6 (Rev. 1). In addition, para 809(f) of SSR-6 (Rev. 1) requires for packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance. Para 503(e) requires that these packages have been maintained during storage in a manner that all requirements specified in SSR-6 (Rev.1) and in the applicable certificates of approval have been fulfilled. The evaluation of ageing mechanisms and their effects including monitoring are part of BAM’s authority assessment tasks related to the mechanical and thermal package design and quality assurance aspects. BAM has compiled the guideline BAM-GGR 023 for the implementation of ageing assessment and related measures into the approval procedure. The implementation of ageing management measures is obligatory in case of extension/renewal of package design approval certificates. BAM has evaluated package designs which are used only for transport as well as package designs for long term interim storage. The assessment of ageing mechanisms associated with the identification of ageing effects on components is the main part of the ageing management plan (AMP). Different approaches regarding AMP structure are introduced. Experiences and approaches about the evaluation of components for the expected package operating time are shown. We are focusing the evaluations of proofs for not accessible and not replaceable components. Operational experiences for these package designs are available and should be considered in the ageing evaluation. Corresponding measures for package monitoring are to be derived based on these results. The measures for monitoring shall be fixed in the Ageing Surveillance Program (ASP) to maintain a specification conform package for the transport on public routes. We show exemplary how results from ageing evaluation during the approval procedure are transferred into the ASP. T2 - PATRAM 2025 CY - San Antonio, TX USA DA - 27.07.2025 KW - RAM KW - Ageing management KW - Transport KW - Radioactive material PY - 2025 AN - OPUS4-63985 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Conclusions from the first return campaign of vitrified High-Level Waste on sea going vessels from the competent authority N2 - Germany has to take back vitrified waste from the reprocessing plants in France and Great Britain. The waste resulted from decades of transporting spent fuel for reprocessing to La Hague and Sellafield. The return campaign from France was concluded in 2024 with the transport of five CASTOR® HAW28M casks to the interim storage facility in Philippsburg in southern Germany. The return of waste from Sellafield comprises three campaigns and a total of 20 CASTOR® HAW28M casks. The first campaign was performed in 2020, consisting of six CASTOR® HAW28M casks, while the second campaign was performed in March 2025, consisting of seven CASTOR® HAW28M casks. The casks were transported by rail from Sellafield to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. The third campaign is expected to be performed during 2026. BAM as part of the German competent authority system was among others involved in the assessment of the sea transport. BAM required for the first transport, among others, an assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of the IMDG code and its supplement the INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - RAM KW - Transport KW - Radioactive material KW - Sea PY - 2025 AN - OPUS4-63983 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Lars A1 - Scheidemann, Robert A1 - Neumeyer, Tino A1 - Neumann, Martin A1 - Komann, Steffen A1 - Wille, Frank T1 - Thightness Assessment of welded Lids for Encapsulations of damaged Spent Nuclear Fuel in the Design Approval Process of Dual-Purpose Casks (DPC) N2 - The disposal of spent nuclear fuel in Germany is ensured using dual-purpose casks (DPC) for transport and interim storage. The leak tightness of the DPC and resulting containment is one of the most important aspects. Additional encapsulations are required for damaged spent nuclear fuel (DSNF) to guarantee safe handling and a separate tight closure. Due to the general design of DPCs for standard fuel assemblies should special requirements be considered for the design of the encapsulations for DSNF to ensure the loading in existing package designs. The absence of a replaceable sealing in the tightness barrier is the main difference for the encapsulations for damaged spent nuclear fuel. Instead, they are welded shut with a lid. The leak tightness of the encapsulation shall be proven in the design approval process for all transport conditions. This is especially valid for accident conditions of transport, where high internal impact forces may occur. BAM as German competent authority is responsible for the safety assessment of mechanical and thermal design, retention of radioactive material and quality assurance aspects of manufacturing and operation. BAM carried out a comprehensive safety assessment concerning the mechanical package design. As there are no representative standards for verifying the leak tightness of a welded lid, two approaches were being pursued. Established German standards may be used for verifying the leak tightness of a weld - but limited to low stresses. Therefore, physical tests were required for higher impact loads. Representative drop tests and highly sensitive leakage tests were performed. The paper presents an overview of the containment assessment by BAM and points out the main findings for the design of welds regarding leak tightness. Both verification procedures are described, on one hand with German standards for lower loads and on the other hand with physical tests for higher impact loads. The leak tightness of the encapsulation weld could be approved based on leakage tests and a corresponding evaluation for all transport conditions. T2 - PATRAM 2025 CY - San Antonio, Texas, USA DA - 27.07.2025 KW - Transport packages KW - Tightness assessment KW - Welded lids KW - Encapsulations PY - 2025 VL - 2025 SP - 1 EP - 11 PB - Institute of Nuclear Materials Management (INMM) CY - Indianapolis AN - OPUS4-64023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Guitton, Matthieu A1 - Chrupek, Thierry A1 - Leblanc, Vincent A1 - Van derTuijn, Jeroen A1 - Kaufhold, Dominik A1 - Kesting, Frederik A1 - Müller, Lars T1 - Multilateral approval of a SCO-III (three spent steam generator lower parts from EDF Fessenheim nuclear power plant) multimodal shipment N2 - A Surface Contaminated Object (SCO) is defined as a solid object which is not itself radioactive, but which has radioactive material distributed on its surfaces. The 2018 Edition of the IAEA Regulations for the Safe Transport of Radioactive Material (SSR-6 Rev. 1) introduced the group SCO-III to transport unpackaged large objects. The two pressurized water reactors of the Fessenheim Nuclear Power Plant, owned by EDF, were shut down in 2020. Previously, for maintenance operations in the year 2002 and 2010, the three steam generators – over 20 metres long, 300 tons – of each reactor were taken out from the reactors, divided in two and stored on site: - EDF shipped the six upper parts, as SCO-I, to Cyclife, in Studsvik (Sweden), in 2021, to be recycled; - EDF plans two transports of the lower parts (three parts for each transport), as SCO-III (considering the higher activity due to the NPP primary coolant) to the same facility. Modes of transport are, from consignor to consignee, road, inland waterways and maritime. The countries crossed by inland waterways, from Neuf-Brisach to Dunkerque (France), are France, Germany, Belgium and the Netherlands. According to the para. 825 of SSR-6 Rev. 1, “multilateral approval shall be required for the shipment of SCO-III”. EDF has submitted to all Competent Authorities an application (para. 827A of SSR-6 Rev. 1), including a transport plan and demonstrations to withstand normal conditions of transport. Despite SSR-6 Rev. 1, national regulations have their own specificities and each Competent Authority has its own assessment procedures. Nevertheless, involved Authorities agreed for a joint review, which included: - the understanding of national regulatory requirements, - the expected level of detail and quality of the safety case, - the feedback from previous shipments of similar type, - the contents, including the conditions, of the approvals to be issued. This joint review demonstrated good coordination between authorities, enabling the application to be processed rapidly, and the various authorities to benefit from each other's expertise and feedback. This was of particular importance, as it was the first application for the transport of an SCO-III assessed by the Competent Authorities involved. Finally, the authorities were able to issue approvals, whose format is certainly in line with their national provisions, but whose content and level of requirements in terms of transport safety are consistent. T2 - PATRAM 2025 CY - San Antonio, Texas, USA DA - 27.07.2025 KW - Shipment KW - Multilateral approval KW - Steam generator KW - SCO-III PY - 2025 VL - 2025 SP - 1 EP - 8 PB - Institute of Nuclear Materials Management (INMM) CY - Indianapolis AN - OPUS4-64026 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Lars T1 - Thightness Assessment of welded Lids for Encapsulations of damaged Spent Nuclear Fuel in the Design Approval Process of Dual-Purpose Casks (DPC) N2 - The disposal of spent nuclear fuel in Germany is ensured using dual-purpose casks (DPC) for transport and interim storage. The leak tightness of the DPC and resulting containment is one of the most important aspects. Additional encapsulations are required for damaged spent nuclear fuel (DSNF) to guarantee safe handling and a separate tight closure. Due to the general design of DPCs for standard fuel assemblies should special requirements be considered for the design of the encapsulations for DSNF to ensure the loading in existing package designs. The absence of a replaceable sealing in the tightness barrier is the main difference for the encapsulations for damaged spent nuclear fuel. Instead, they are welded shut with a lid. The leak tightness of the encapsulation shall be proven in the design approval process for all transport conditions. This is especially valid for accident conditions of transport, where high internal impact forces may occur. BAM as German competent authority is responsible for the safety assessment of mechanical and thermal design, retention of radioactive material and quality assurance aspects of manufacturing and operation. BAM carried out a comprehensive safety assessment concerning the mechanical package design. As there are no representative standards for verifying the leak tightness of a welded lid, two approaches were being pursued. Established German standards may be used for verifying the leak tightness of a weld - but limited to low stresses. Therefore, physical tests were required for higher impact loads. Representative drop tests and highly sensitive leakage tests were performed. The paper presents an overview of the containment assessment by BAM and points out the main findings for the design of welds regarding leak tightness. Both verification procedures are described, on one hand with German standards for lower loads and on the other hand with physical tests for higher impact loads. The leak tightness of the encapsulation weld could be approved based on leakage tests and a corresponding evaluation for all transport conditions. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - Tightness assessment KW - Welded lids KW - Transport packages KW - Encapsulations PY - 2025 AN - OPUS4-64017 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias ED - Monavari, Mehran ED - Bertovic, Marija ED - Wille, Frank T1 - AI-Based Documentation Analysis for Safety Assessment of Packages for Radioactive Material N2 - The transportation of radioactive material requires, dependent on type and quantity of the radioactive material, a regulatory approval based on the package type. Safety assessments shall be conducted in compliance with the International Atomic Energy Agency (IAEA) regulations and documented in a comprehensive package design safety report to obtain approval from authority. This comprehensive safety report evaluates a broad range of requirements from the regulations, including mechanical, thermal, shielding, criticality and transport requirements and controls, and testing assessments. Additionally, it encompasses supporting documents such as specifications, inspections, certifications, drawings, and guidelines in a variety of complex documents. Safety and manufacturing reports contain multiple interconnected sub-reports covering various topics. Changes, such as component modifications, material property updates, or regulatory revisions, often impact multiple sections of the safety analysis reports, making even minor adjustments complex and time-consuming. Each transport package has unique requirements to be fulfilled, making every safety report distinct, despite following the same regulatory framework. Most documentation exists in standard digital formats but is often not machine interpretable, preventing automated analysis of the critical dependencies between them. This paper argues that moving beyond simple digitization towards structured knowledge representation is essential for addressing these challenges. We propose a multi-stage approach, beginning with foundational AI technologies such as Large Language Models (LLMs) and Retrieval-Augmented Generation (RAG), and progressing toward the construction of Knowledge Graphs (KGs). KGs convert unstructured and semi-structured information into a connected, queryable network, enabling precise tracing and visualization of complex interdependencies within the documentation landscape. By linking interpretable content directly to datasheets, tables, simulations, experimental results, standards, and regulations, such a system would automatically identify changes and interdependencies. Related conditions could be validated using AI-based tools, reducing the need for manual intervention, improving both efficiency and safety. Human error plays a significant role in drafting, reviewing, and revising safety reports, often requiring iterative review cycles and multiple reviewers before approval. A digital quality infrastructure could reduce iterations and further improve efficiency. Integrating AI into this process could optimize safety assessments and enhance their robustness by leveraging interpretability to enhance safety. This preliminary study explores the readiness and requirements for using intelligent documentation analysis system in the context of regulatory compliance for package safety for the transport of radioactive material. By analysing current documentation workflows, we identify how LLM-based tools can interpret complex safety reports and highlight critical interdependencies and then demonstrate why a KG-based architecture is necessary to robustly manage and query critical interdependencies. This lays the groundwork for future agentic AI systems capable of proactively supporting the safety assessment lifecycle, while stressing the importance of robust data governance and AI reliability in this highly regulated context. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - AI, RAG, LLM, Knowledge Graph PY - 2025 SP - 1 EP - 10 PB - Institute of Nuclear Materials Management (INMM) AN - OPUS4-63863 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian A1 - Gleim, Tobias A1 - Wille, Frank T1 - Experimental and numerical analyses of hydrogen flames for the thermal testing of transport packages for radioactive material N2 - In this paper we present an update of the hydrogen based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials [ The test rig is capable of combusting hydrogen for a wide range of different burner geometries, mass flows , hydrogen blends and single jet flame operation s as well as a full array of burners for thermal testing can be set up. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and simulations must be carried out in order to develop a viable concept for hydrogen fires. In a first step of the feasibility study, the temperature , structure, and radiative behavior of hydrogen jet flames must be surveyed. The simulation with a single hydrogen flame was investigated in a previous work. In the next step the results are used to study the interaction and structural behavior of multiple jet flames in proximity with varying nozzle distances. With the test rig completed, it will be possible in future works to design burner frames suitable for fire reference tests to make comparisons with pool and propane fires used in assessment procedure today. Thus, preliminary comparative numerical simulations are conducted to model the behavior of overlapping hydrogen jet flames using the software package Ansys®. This paper gives an overview on the current state and design of the test rig. Furthermore, the results of the simulations show that nozzle geometry, mas s flow and nozzle distance provide significant design margin for designing a test fire capable of fully engulfing a specimen. T2 - PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Computational Fluid Dynamics (CFD) KW - Fire testing KW - Hydrogen KW - IAEA PY - 2025 SP - 1 EP - 10 AN - OPUS4-63864 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Affagard, Jean-Sebastien A1 - Gleim, Tobias A1 - Louis, Baptiste A1 - Quercetti, Thomas A1 - Ledroit, Frédéric A1 - Létang, Eric T1 - Towards a simplifiedmodel of the delayed impact: numerical and experimental outlook N2 - The IAEA Regulations for the Safe Transport of Radioactive Material No. SSR-6 require drop tests for demonstrating the ability of a package to withstand accident conditions of transport. In case a gap exists between the contents and the lid, it can result in a delayed impact of the content onto the lid system during a vertical drop test. The kinematic energy transmitted to the lid in such cases can be significant due to the stiffness of the impact, leading to high stresses in the bolts compared to a configuration without a gap. In the past, IRSN and BAM have individually investigated the modelling of the delayed impact phenomenon. BAM has examined the effects of the delayed impact phenomenon for spent fuel packages in a comparative analysis between experiments and simulations, which was presented at SMIRT 2013. Meanwhile, IRSN’s has developed a simple numerical tool that can quickly evaluate the influence of various parameters before considering a more complex finite element numerical calculation. This tool was presented at PATRAM 2022. In 2023, BAM and IRSN (now ASNR - French nuclear safety and radiation protection authority) decided to jointly pursue their study on the delayed impact phenomenon, incorporating damping effects, by developing new insights and techniques. To this end, a controlled and simplified set of experiments needs to be developed to calibrate and validate the simplified model. These experiments will record velocity, position of parts, strain and accelerations. The parameters and the configurations necessary for the development of the mock-up, as well as the placement and quantity of sensors, are determined through extensive pre-calculations using both complex finite element models and the simplified approach. A key challenge involves precisely controlling the drop of the mock-up to accurately replicate the theoretical contact and damping conditions. Advanced sensor technologies will be employed to acquire reliable and sufficient data. The tests are designed and conducted at BAM's TTS drop test facility in collaboration with ASNR. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - Experiments KW - Impact KW - Drop Tower PY - 2025 SP - 1 EP - 11 CY - Institute of Nuclear Materials Management (INMM) AN - OPUS4-63870 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Feldkamp, Martin A1 - Gleim, Tobias A1 - Musolff, André A1 - Werner, Jan A1 - Wille, Frank T1 - Fire Test Stand for Thermal Testing of Large Packages for the Transport of Radioactive Materials N2 - Packages for the transport of high level radioactive materials are designed to withstand severe accidents. These packages must comply with the specific safety requirements SSR 6 [ of the International Atomic Energy Agency (IAEA). To guarantee compliance with these requirements, specific mechanical and thermal tests need to be addressed r egard ing the package type. Typically, the r egulations prescribe mechanical tests followed by a thermal test as part of a cumulative test scenario. The thermal test is specified by the exposure of a test specimen for a period of 30 minutes to a thermal environment that provides a heat flux equivalent to that of a hydrocarbon fuel air fire with an av erage fire temperature of at least 800 °C fully flame engulfing the test specimen. The Federal Institute for Materials Research and Testing (BAM) operates various test facilities for this purpose at their Test Site for Technical Safety (near Berlin in Germany). Thermal tests for large packages are conducted in an established fire test stand that may be adapted by the test setup to the geometric boundary conditions of a test specimen. This fire test stand is built for test specimens with masses up to 200,000 kg an d geometric dimensions relating to large transport packages including their impact limiters. The test specimen is usually placed on a water cooled support frame in the middle of the test stand. The fire is realized by burning propane gas which is released in liquid state from an array of gas nozzles arranged in the form of a burner ring surrounding the test specimen. For particularly extra large test specimens, two burner rings are used on top of each other and at different heights to firstly achieve full f ire engulfment with a significantly larger volume of fire and secondly to achieve the required heat output , cf. In advance of a regular thermal test BAM usually performs so called fire reference tests to determine the test conditions for compliance with the IAEA requirements. These tests are performed using a generic package which corresponds to the external geometr ic dimensions of the test specimen used later in the approval test. Then, this reference package is exposed to a fire under defined test parameters whereas the corresponding heat input determined from the temperature changes measured is regarded as main cr iterion for proofing compliance with the IAEA criteria. The paper shows the experimental proof of the suitability of BAM’s fire test stand for thermal testing of extra large packages. The heat input and fire temperatures fully meet the IAEA criteria and can also be set significantly higher for example for extra regulatory testing. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - IAEA Regu-lations KW - Fire Test Stand KW - Accident Scenario KW - Fire Qualification PY - 2025 SP - 1 EP - 10 CY - Institute of Nuclear Materials Management (INMM) AN - OPUS4-63872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naster, Maximilian T1 - Experimental and numerical analyses of hydrogen flames for the thermal testing of transport packages for radioactive material N2 - In this paper we present an update of the hydrogen-based test rig for an ongoing feasibility study of using hydrogen as an energy source for the thermal testing of transport packages containing radioactive materials. The test rig is capable of combusting hydrogen for a wide range of different burner geometries, mass flows, hydrogen blends and single jet flame operations as well as a full array of burners for thermal testing can be set up. As this type of fire test according to the IAEA boundary conditions does not yet exist, a large number of preliminary investigations, safety assessments and simulations must be carried out in order to develop a viable concept for hydrogen fires. In a first step of the feasibility study, the temperature, structure, and radiative behavior of hydrogen jet flames must be surveyed. The simulation with a single hydrogen flame was investigated in a previous work. In the next step the results are used to study the interaction and structural behavior of multiple jet flames in proximity with varying nozzle distances. With the test rig completed, it will be possible in future works to design burner frames suitable for fire reference tests to make comparisons with pool and propane fires used in assessment procedure today. Thus, preliminary comparative numerical simulations are conducted to model the behavior of overlapping hydrogen jet flames using the software package Ansys®. This paper gives an overview on the current state and design of the test rig. Furthermore, the results of the simulations show that nozzle geometry, mass flow and nozzle distance provide significant design margin for designing a test fire capable of fully engulfing a specimen. T2 - PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Computational Fluid Dynamics (CFD) KW - Hydrogen KW - IAEA fire test PY - 2025 AN - OPUS4-63865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Affagard, Jean-Sebastien T1 - Towards a simplifiedmodel of the delayed impact: numerical and experimental outlook N2 - The IAEA Regulations for the Safe Transport of Radioactive Material No. SSR-6 require drop tests for demonstrating the ability of a package to withstand accident conditions of transport. In case a gap exists between the contents and the lid, it can result in a delayed impact of the content onto the lid system during a vertical drop test. The kinematic energy transmitted to the lid in such cases can be significant due to the stiffness of the impact, leading to high stresses in the bolts compared to a configuration without a gap. In the past, IRSN and BAM have individually investigated the modelling of the delayed impact phenomenon. BAM has examined the effects of the delayed impact phenomenon for spent fuel packages in a comparative analysis between experiments and simulations, which was presented at SMIRT 2013. Meanwhile, IRSN’s has developed a simple numerical tool that can quickly evaluate the influence of various parameters before considering a more complex finite element numerical calculation. This tool was presented at PATRAM 2022. In 2023, BAM and IRSN (now ASNR – French nuclear safety and radiation protection authority) decided to jointly pursue their study on the delayed impact phenomenon, incorporating damping effects, by developing new insights and techniques. To this end, a controlled and simplified set of experiments needs to be developed to calibrate and validate the simplified model. These experiments will record velocity, position of parts, strain and accelerations. The parameters and configurations necessary for the development of the mock-up, as well as the placement and quantity of sensors, are determined through extensive pre-calculations using both complex finite element models and the simplified approach. A key challenge involves precisely controlling the drop of the mock-up to accurately replicate the theoretical contact and damping conditions. Advanced sensor technologies will be employed to acquire reliable and sufficient data. The tests are designed and conducted at BAM's TTS drop test facility in collaboration with ASNR. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - Experiments KW - Impact KW - Drop Tower PY - 2025 AN - OPUS4-63869 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - AI-Driven Documentation Analysis Supporting Safety Assessment of Transport Packages N2 - The transportation of radioactive material requires, dependent on type and quantity of the radioactive material, a regulatory approval based on the package type. Safety assessments shall be conducted in compliance with the International Atomic Energy Agency (IAEA) regulations and documented in a comprehensive package design safety report to obtain approval from authority. This comprehensive safety report evaluates a broad range of requirements from the regulations, including mechanical, thermal, shielding, criticality and transport requirements and controls, and testing assessments. Additionally, it encompasses supporting documents such as specifications, inspections, certifications, drawings, and guidelines in a variety of complex documents. Safety and manufacturing reports contain multiple interconnected sub-reports covering various topics. Changes, such as component modifications, material property updates, or regulatory revisions, often impact multiple sections of the safety analysis reports, making even minor adjustments complex and time-consuming. Each transport package has unique requirements to be fulfilled, making every safety report distinct, despite following the same regulatory framework. Most documentation exists in standard digital formats but is often not machine interpretable, preventing automated analysis of the critical dependencies between them. This paper argues that moving beyond simple digitization towards structured knowledge representation is essential for addressing these challenges. We propose a multi-stage approach, beginning with foundational AI technologies such as Large Language Models (LLMs) and Retrieval-Augmented Generation (RAG), and progressing toward the construction of Knowledge Graphs (KGs). KGs convert unstructured and semi-structured information into a connected, queryable network, enabling precise tracing and visualization of complex interdependencies within the documentation landscape. By linking interpretable content directly to datasheets, tables, simulations, experimental results, standards, and regulations, such a system would automatically identify changes and interdependencies. Related conditions could be validated using AI-based tools, reducing the need for manual intervention, improving both efficiency and safety. Human error plays a significant role in drafting, reviewing, and revising safety reports, often requiring iterative review cycles and multiple reviewers before approval. A digital quality infrastructure could reduce iterations and further improve efficiency. Integrating AI into this process could optimize safety assessments and enhance their robustness by leveraging interpretability to enhance safety. This preliminary study explores the readiness and requirements for using intelligent documentation analysis system in the context of regulatory compliance for package safety for the transport of radioactive material. By analysing current documentation workflows, we identify how LLM-based tools can interpret complex safety reports and highlight critical interdependencies and then demonstrate why a KG-based architecture is necessary to robustly manage and query critical interdependencies. This lays the groundwork for future agentic AI systems capable of proactively supporting the safety assessment lifecycle, while stressing the importance of robust data governance and AI reliability in this highly regulated context. T2 - Sandia-BAM Technical Exchange CY - Albuquerque, NM, USA DA - 23.07.2025 KW - AI, RAG, LLM, Knowledge Graph PY - 2025 AN - OPUS4-63860 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Enhancement of Fire Test Stand Performance at Test Site of BAM: Installation and Evaluation of an Augmented System with a Fire Reference Package N2 - Packages for the transport of radioactive material are designed to endure severe accidents. Packages for the transportation of radioactive material must demon-strate that the package can withstand certain prescribed tests from the IAEA Reg-ulations [1]. In addition to mechanical tests, a thermal test in form of a fire test must be carried out. As packages to be tested at BAM are significantly larger than previous package designs, BAM has expanded an existing fire test stand. A modular concept is chosen, which means that the arrangement of the burner noz-zles can be adapted to the test specimen. The dimensions of the burner rings, the type, the orientation and the number of burner nozzles can be varied depending on the test specimen. In addition, various pumps can be used to set the corre-sponding mass flow. With the help of a calorimeter test, the fire test stand can be qualified for a specific size of packages regarding the boundary conditions of the IAEA Regulations [1]. Due to the typically wood filled impact limiters in German package designs, a fire test is necessary, as experiments have shown that possible openings that occurred during a mechanical test contributed to the ignition of the wood filled impact limiters within the prescribed 30 minutes of the IAEA Regula-tions [1]. From a series of experiments, two experiments are presented to show the possibilities to obtain different temperatures and temperature rates in the test specimen. In addition to sensor data, the heat flux into the package is calculated to verify that the IAEA boundary conditions are satisfied. In addition to the tem-perature data, other data such as wind speed and wind direction are also recorded to explain subsequent effects in the measurement data in a comprehensible man-ner. T2 - Sandia-BAM Technical Exchange CY - Albuquerque, NM, USA DA - 23.07.2025 KW - IAEA Regulations KW - Fire Test Stand KW - Accident Scenario KW - Fire Qualification PY - 2025 AN - OPUS4-63861 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Müller, Lars A1 - Neumann, Martin A1 - Wille, Frank T1 - Shipment of SCO-II – Authority assessment of mechanical aspects and quality management N2 - The decommissioning of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, or coolant pumps. These components or objects are large in size and mass with up to 6 meters in diameter and 20 meters in length and a weight of up to 400 tons. They are often transported to a storage, disposal, or recycling facility. Large components from nuclear facilities may often not be packed and need to be transported unpackaged due to size and weight. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - radioaktive Stoffe, Rückbau kerntechnischer Anlagen, Transport, Gefahrgut PY - 2025 SP - 1 EP - 10 AN - OPUS4-63878 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen T1 - Shipment of SCO-II – Authority assessment of mechanical aspects and quality management N2 - The decommissioning of nuclear facilities necessitates either the storage or disposal of large radioactive components such as steam generators, pressurizers, reactor pressure vessels and heads, or coolant pumps. These components or objects are large in size and mass with up to 6 meters in diameter and 20 meters in length and a weight of up to 400 tons. They are often transported to a storage, disposal, or recycling facility. Large components from nuclear facilities may often not be packed and need to be transported unpackaged due to size and weight. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - Transport KW - Radioaktive Stoffe KW - Rückbau kerntechnischer Anlagen KW - Gefahrgut PY - 2025 AN - OPUS4-63877 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Fire Test Stand for Thermal Testing of Large Packages for the Transport of Radioactive Materials N2 - Packages for the transport of spent nuclear fuel are designed to withstand severe accidents and must ensure compliance with the IAEA-Regulations prescribing mechanical tests followed by a thermal test. The thermal test involves that a test specimen is exposed to a thermal environment for 30 minutes, simulating the conditions of a hydrocarbon fuel-air fire. The average fire temperature is at least 800°C, and the fire completely engulfs the test specimen. In advance of a regular fire test, BAM performs so-called fire reference tests or calorimeter tests with a fire reference package (FRP) to determine the test conditions for compliance with the IAEA-requirements. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - Experiment KW - Thermal Test KW - Fire PY - 2025 AN - OPUS4-63871 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - AI-Based Documentation Analysis for Safety Assessment of Packages for Radioactive Material N2 - The transportation of radioactive material requires, dependent on type and quantity of the radioactive material, a regulatory approval based on the package type. Safety assessments shall be conducted in compliance with the International Atomic Energy Agency (IAEA) regulations and documented in a comprehensive package design safety report to obtain approval from authority. This comprehensive safety report evaluates a broad range of requirements from the regulations, including mechanical, thermal, shielding, criticality and transport requirements and controls, and testing assessments. Additionally, it encompasses supporting documents such as specifications, inspections, certifications, drawings, and guidelines in a variety of complex documents. Safety and manufacturing reports contain multiple interconnected sub-reports covering various topics. Changes, such as component modifications, material property updates, or regulatory revisions, often impact multiple sections of the safety analysis reports, making even minor adjustments complex and time-consuming. Each transport package has unique requirements to be fulfilled, making every safety report distinct, despite following the same regulatory framework. Most documentation exists in standard digital formats but is often not machine interpretable, preventing automated analysis of the critical dependencies between them. This paper argues that moving beyond simple digitization towards structured knowledge representation is essential for addressing these challenges. We propose a multi-stage approach, beginning with foundational AI technologies such as Large Language Models (LLMs) and Retrieval-Augmented Generation (RAG), and progressing toward the construction of Knowledge Graphs (KGs). KGs convert unstructured and semi-structured information into a connected, queryable network, enabling precise tracing and visualization of complex interdependencies within the documentation landscape. By linking interpretable content directly to datasheets, tables, simulations, experimental results, standards, and regulations, such a system would automatically identify changes and interdependencies. Related conditions could be validated using AI-based tools, reducing the need for manual intervention, improving both efficiency and safety. Human error plays a significant role in drafting, reviewing, and revising safety reports, often requiring iterative review cycles and multiple reviewers before approval. A digital quality infrastructure could reduce iterations and further improve efficiency. Integrating AI into this process could optimize safety assessments and enhance their robustness by leveraging interpretability to enhance safety. This preliminary study explores the readiness and requirements for using intelligent documentation analysis system in the context of regulatory compliance for package safety for the transport of radioactive material. By analysing current documentation workflows, we identify how LLM-based tools can interpret complex safety reports and highlight critical interdependencies and then demonstrate why a KG-based architecture is necessary to robustly manage and query critical interdependencies. This lays the groundwork for future agentic AI systems capable of proactively supporting the safety assessment lifecycle, while stressing the importance of robust data governance and AI reliability in this highly regulated context. T2 - PATRAM 2025 CY - San Antonio, TX, USA DA - 27.07.2025 KW - Knowledge Graph KW - AI KW - RAG KW - LLM PY - 2025 AN - OPUS4-63862 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Gleim, Tobias A1 - Quercetti, Thomas A1 - Wille, Frank T1 - Evaluation of Convective Heat Transfer Coefficients with CFD for Heat Flux Calculation in Combustion Chamber N2 - Packages for the transport of high-level radioactive waste are designed to withstand severe accidents. To obtain approval for transport, these packages must adhere to the specification-based criteria of regulations established by the International Atomic Energy Agency (IAEA). To ensure compliance with the regulations, mechanical and thermal tests need to be conducted regarding the package type. The requirements define mechanical tests followed by a thermal test, including criteria ensuring the package design’s ability to withstand severe accidents. Heavy-weight packages for the safe transport of radioactive materials are equipped with impact limiters, which are often built with porous materials such as densely packed wood reinforced by steel sheet structures. These components absorb the kinetic energy during the impact of the package in drop tests and thus dampen the acceleration of other package components which supports the package to meet the requirements of the IAEA regulations. Following the mechanical tests, the package must, with its predamaged impact limiters, endure a thermal test defined precisely in the IAEA regulations. The thermal test is defined as a 30-min, fully engulfing 800 °C fire and a following time under ambient conditions for a sufficient period to ensure that temperatures in the specimen decrease in all parts of the specimen. During and following the thermal test, the specimen shall not be artificially cooled, and any combustion of materials of the specimen shall be permitted to proceed naturally. A wood-filled impact limiter can continue to release thermal energy during an ongoing combustion process, thus defining relevant package temperatures. Heat flux from a potentially burning impact limiter to the package is important for the safety evaluation of transport packages. A test setup was developed to approach the energy flow investigation and examine the combustion behaviour of porous materials encapsulated in predamaged cylindrical metal enclosures under various conditions. The setup consists of a combustion chamber for thermal tests under adjustable and defined boundary conditions. The temperature development of the test specimens can be observed from outside using a thermographic imager with high-definition cameras, and the mass loss of the test specimen can be measured in the combustion chamber. Convective heat transfer coefficients for various boundary conditions must be defined for use with experimentally gathered test specimen surface temperature data for heat flux evaluations. The airflow conditions in the combustion chamber were analysed using computational fluid dynamics (CFD) calculations in OpenFOAM with respect to the convective heat transfer coefficients at the surface of a hot test specimen. A convergence study was performed, and sensitivity analyses for different test specimen surface temperatures and exhaust gas volume flows were conducted. T2 - ASME PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Quebec, Canada DA - 20.07.2025 KW - Heat Transfer KW - Convection KW - OpenFOAM KW - Combustion PY - 2025 SP - 1 EP - 7 PB - American society of mechanical engineers (ASME) AN - OPUS4-63901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Feldkamp, Martin A1 - Gleim, Tobias A1 - Musolff, Andre A1 - Werner, Jan A1 - Wille, Frank T1 - A fire test stand for thermal testing of extra-large packages N2 - Packages for the transport of high-level radioactive materials are designed to withstand severe accidents. These packages must adhere to the specification-based criteria of the International Transport Regulations of the International Atomic Energy Agency (IAEA). To ensure compliance with these requirements, specific mechanical and thermal tests need to be addressed with respect to the package type. Typically, the Regulations prescribe mechanical tests followed by a thermal test as part of a cumulative test scenario. The thermal test is specified by the exposure of a test specimen for a period of 30 minutes to a thermal invironment that provides a heat flux equivalent to that of a hydrocarbon fuel-air fire with an average fire temperature of at least 800 °C fully flame engulfing the test specimen. The Federal Institute for Materials Research and Testing (BAM) operates various test facilities for this purpose at their test site (TTS) near Berlin in Germany. Thermal tests for large packages are carried out in an established fire test stand that can be adapted by the test-setup to the geometric boundary conditions of a test specimen. This fire test stand is built for test specimens with masses up to 200,000 kg and geometric dimensions relating to large transport packages including their impact limiters. The test specimen is usually placed on a water-cooled support frame in the middle of the test-stand. The fire is realized by burning propane gas which is released in liquid state from an array of gas nozzles arranged in the form of a burner ring surrounding the test specimen. For particularly extra-large test specimens, two burner rings are used on top of each other and at different heights in order to firstly achieve full fire engulfment with a significantly larger volume of fire and secondly to achieve the required heat output. In advance of a regular thermal test BAM usually performs so-called fire reference tests to determine the test conditions for compliance with the IAEA requirements. These tests are performed using a generic package which corresponds to the external geometric dimensions of the test specimen used later in the approval test. Then, this reference package is exposed to a fire under defined test parameters whereas the corresponding heat input determined from the temperature changes measured is regarded as main criterion for proofing compliance with the IAEA criteria.The paper shows the experimental proof of the suitability of BAM’s fire test stand for thermal testing of extra-large packages. The heat input and fire temperatures fully meet the IAEA criteria but can also be set significantly higher for e.g. extra-regulatory testing. T2 - ASME PVP 2025 CY - Montreal, Quebec, Kanada DA - 20.07.2025 KW - Test stand KW - Thermal testing KW - Package KW - Fire PY - 2025 SP - 1 EP - 6 AN - OPUS4-63892 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Potential Effects of Battery and Hydrogen Fires regarding Regulatory Requirements N2 - Die internationalen Sicherheitsanforderungen für den Transport radioaktiver Stoffe sind in den IAEO-Vorschriften SSR-6 festgelegt. Diese wurden in den 1960er Jahren entwickelt und seitdem nur in begrenztem Umfang angepasst. Sie bilden die Basis für die Regelwerke der verschiedenen Verkehrsträger – darunter auch das ADR (Europäisches Übereinkommen über die internationale Beförderung gefährlicher Güter auf der Straße). Die SSR-6 wird regelmäßig vom TRANSSC-Gremium der IAEO überprüft und aktualisiert. In diesen Prozess fließen aktuelle wissenschaftliche Erkenntnisse sowie praktische Erfahrungen ein, um die Sicherheit beim Transport radioaktiver Materialien kontinuierlich zu verbessern. Im Rahmen der 47. TRANSSC-Sitzung stellte die BAM (Bundesanstalt für Materialforschung und -prüfung) aktuelle Forschungsergebnisse zu Unfallszenarien mit Batterien und Wasserstoff vor und adressierte zentrale sicherheitsrelevante Fragestellungen. Aufgrund des großen internationalen Interesses, insbesondere da vergleichbare Erkenntnisse aus anderen UN-Mitgliedstaaten bislang nicht vorlagen, wurden diese Fragestellungen ab der 48. Sitzung offiziell in das Arbeitsprogramm aufgenommen. Vor der 48. TRANSSC-Sitzung führten BAM und BASE eine gemeinsame Befragung aller UN-Mitgliedstaaten mittels eines Fragebogens durch. Die Ergebnisse wurden im Rahmen der 48. TRANSSC-Sitzung vorgestellt. Dabei zeigte sich, dass in den befragten Ländern bislang keine spezifischen nationalen Regelungen oder Einschränkungen im Hinblick auf Fahrzeuge mit alternativen Antrieben bestehen. Gleichzeitig wurde jedoch auf ein potenzielles Risiko mit derzeit nicht abschätzbarem Ausmaß hingewiesen. N2 - Hier: The IAEA regulations for the safe transport of radioactive material (IAEA SSR-6) define the safety requirements for different package types and consider different transport conditions. The accident conditions of transport specify different mechanical and thermal tests based on investigations of real accident scenarios. Considering the rapid development of new boundary conditions of transport such as electric mobility and the use of hydrogen as energy source for trucks and other kind of vehicles, potential effects of battery and hydrogen fires in transport accidents should be investigated. The aim is to evaluate the existing test requirements developed and derived decades ago, whether they are covering the current transport situation. This presentation will briefly present the reasons for detailed investigations as bases for a coordinated research project under the roof of the IAEA. T2 - WP.15 IWG-EV 22nd session CY - Online-Meeting DA - 23.07.2025 KW - Requirements KW - Battery Fire KW - Experiment KW - IAEA PY - 2025 AN - OPUS4-63900 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin T1 - Evaluation of Convective Heat Transfer Coefficients with CFD for Heat Flux Calculation in Combustion Chamber N2 - Packages for the transport of high-level radioactive waste are designed to withstand severe accidents. To obtain approval for transport, these packages must adhere to the specification-based criteria of regulations established by the International Atomic Energy Agency (IAEA). To ensure compliance with the regulations, mechanical and thermal tests need to be conducted regarding the package type. The requirements define mechanical tests followed by a thermal test, including criteria ensuring the package design’s ability to withstand severe accidents. Heavy-weight packages for the safe transport of radioactive materials are equipped with impact limiters, which are often built with porous materials such as densely packed wood reinforced by steel sheet structures. These components absorb the kinetic energy during the impact of the package in drop tests and thus dampen the acceleration of other package components which supports the package to meet the requirements of the IAEA regulations. Following the mechanical tests, the package must, with its predamaged impact limiters, endure a thermal test defined precisely in the IAEA regulations. The thermal test is defined as a 30-min, fully engulfing 800 °C fire and a following time under ambient conditions for a sufficient period to ensure that temperatures in the specimen decrease in all parts of the specimen. During and following the thermal test, the specimen shall not be artificially cooled, and any combustion of materials of the specimen shall be permitted to proceed naturally. A wood-filled impact limiter can continue to release thermal energy during an ongoing combustion process, thus defining relevant package temperatures. Heat flux from a potentially burning impact limiter to the package is important for the safety evaluation of transport packages. A test setup was developed to approach the energy flow investigation and examine the combustion behaviour of porous materials encapsulated in predamaged cylindrical metal enclosures under various conditions. The setup consists of a combustion chamber for thermal tests under adjustable and defined boundary conditions. The temperature development of the test specimens can be observed from outside using a thermographic imager with high-definition cameras, and the mass loss of the test specimen can be measured in the combustion chamber. Convective heat transfer coefficients for various boundary conditions must be defined for use with experimentally gathered test specimen surface temperature data for heat flux evaluations. The airflow conditions in the combustion chamber were analysed using computational fluid dynamics (CFD) calculations in OpenFOAM with respect to the convective heat transfer coefficients at the surface of a hot test specimen. A convergence study was performed, and sensitivity analyses for different test specimen surface temperatures and exhaust gas volume flows were conducted. T2 - ASME PVP2025, Pressure Vessels & Piping Conference CY - Montréal, Quebec, Canada DA - 20.07.2025 KW - Heat Transfer KW - Convective Heat Transfer Coefficient KW - Combustion KW - OpenFOAM KW - Computational Fluid Dynamics (CFD) PY - 2025 AN - OPUS4-63902 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Design assessment, approval of management systems and ageing aspects of transport packages for radioactive material not requiring competent authority approval of design N2 - Most transports of radioactive materials are carried out with packages not requiring competent authority approval of design. These encompass – in accordance with the IAEA SSR-6 [1] regulations – packages of the classification excepted, Industrial packages Type 1, 2 and 3 and Type A packages. Currently an upsurge in number and variation of these package designs can be seen in Germany, resulting from the phase out of nuclear energy in Germany as well as e. g. increased use of radioactive material for medical purposes. A design assessment regarding the package safety is required in the international IAEA SSR-6 [1] regulations. BAM operates facilities for the performance of all regulatory tests required such as drop towers for a wide range of package masses and dimensions, fire test, leak tightness measurements and pressure test facilities. Experiences with several package types are shown. Additionally, IAEA SSR-6 [1] requires the establishment of a management system for design, manufacture, maintenance, and repair of the packaging as well as for the preparation, consigning, loading, carriage, unloading and receipt of the package. Relevant for Germany, BAM has published guidance material on the process of management system acceptance in the technical guide BAM-GGR 016 [2]. The requirements encompass quality management plans for the manufacturing of packages including independent manufacturing surveillance and specific instructions for operation, maintenance, and repair of packagings. Examples for management system specifics and requirements are given. Since the latest edition of the IAEA SSR-6 [1] regulations an ageing evaluation including systematic ageing management measures are required for all kind of package types. BAM is going to update the guidance material BAM-GGR 016 [2] to support the stakeholders with relevant information to fulfil the ageing aspect for packages not requiring competent authority approval. The paper explains how the ageing aspect may be included in the safety evaluation process and the management system measures and will give an outlook for the future guidance material. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-les-Pins, France DA - 11.06.2023 KW - Radioactive material KW - Type A package KW - Management system KW - Tests KW - Non-approved PY - 2023 AN - OPUS4-57704 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven A1 - Komann, Steffen A1 - Neumann, Martin A1 - Reichardt, Adrian A1 - Müller, Lars A1 - Wille, Frank T1 - Ageing management measures of transport packages for radioactive materials N2 - The consideration of ageing mechanisms is with integration into the IAEA-requirements now obligatory for the design of transport packages. For packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance are required. Therefore, these packages have been maintained during storage in a manner that all requirements specified in the IAEA-requirements and in the applicable certificates of approval have been fulfilled. BAM is the competent authority in Germany for evaluating the thermal and mechanical design of packages for the transport of radioactive materials. In this context, BAM also evaluates the aging mechanisms and aging effects occurring during the long-term storage period of such transport packages. BAM has developed a guideline for the implementation of ageing assessment and of the measures for ageing management into the approval procedure based on IAEA-requirements. The goal of the presented paper is to introduce this guideline and the general approach for ageing management requirements and to describe the application to a specific package design. The type and amount of the ageing management not only depend on the use of the packaging, but also on the accessibility of the components that are considered in the ageing assessment. The different operating phases of a packaging are considered for the ageing assessment, such as loading, interim storage or transport. The implementation of measures for ageing management is divided into three levels – systemic measures, package design related measures and documentation. The systemic measures are attributed to the general management system and define the whole activities for organization of ageing management like structure, responsibilities, documentation, reports and evaluation. The package design related measures are defined in an ageing management plan. These measures shall ensure that the anticipated changes of the package design under consideration of ageing effects still complies with the design approval specification. Therefore, an ageing surveillance program and, if necessary, a gap analysis program shall be developed. The ageing management documentation ensures the continuous documentation of the compliance of a specific package to the approved package design, comprising mainly records resulting from operation and surveillance. T2 - RAMTRANS 2024 CY - London, United Kingdom DA - 15.05.2024 KW - Radioactive Materials KW - Ageing Management KW - Transport Packages KW - Dual Purpose Casks PY - 2024 VL - 2024 SP - 1 EP - 8 PB - Nuclear Institute CY - London AN - OPUS4-60186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen T1 - Transportbehälter für Klasse 7 - Ein Überblick N2 - Die Präsentation gibt einen Überblick über die Tranportbehälter der Klasse 7. Behandelt werden neben der Versandstückklassifikation auch die Anforderungen an diese Verpackungen gemäß der gefahrgutrechtlichen Vorschriften. T2 - 30. Münchner Gefahrguttage CY - Online meeting DA - 20.07.2020 KW - Gefahrgutrecht KW - Transportbehälter KW - Radioaktives Material KW - Zulassungspflichtige Versandstücke PY - 2020 AN - OPUS4-51104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schubert, Sven T1 - BAM-GGR 023 - Ageing Management for CA Approved RAM Transport Packages N2 - The consideration of ageing mechanisms is with integration into the IAEA-requirements now obligatory for the design of transport packages. For packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance are required. Therefore, these packages have been maintained during storage in a manner that all requirements specified in the IAEA-requirements and in the applicable certificates of approval have been fulfilled. BAM is the competent authority in Germany for evaluating the thermal and mechanical design of packages for the transport of radioactive materials. In this context, BAM also evaluates the aging mechanisms and aging effects occurring during the long-term storage period of such transport packages. BAM has developed a guideline for the implementation of ageing assessment and of the measures for ageing management into the approval procedure based on IAEA-requirements. The goal of the presented paper is to introduce this guideline and the general approach for ageing management requirements and to describe the application to a specific package design. The type and amount of the ageing management not only depend on the use of the packaging, but also on the accessibility of the components that are considered in the ageing assessment. The different operating phases of a packaging are considered for the ageing assessment, such as loading, interim storage or transport. The implementation of measures for ageing management is divided into three levels – systemic measures, package design related measures and documentation. The systemic measures are attributed to the general management system and define the whole activities for organization of ageing management like structure, responsibilities, documentation, reports and evaluation. The package design related measures are defined in an ageing management plan. These measures shall ensure that the anticipated changes of the package design under consideration of ageing effects still complies with the design approval specification. Therefore, an ageing surveillance program and, if necessary, a gap analysis program shall be developed. The ageing management documentation ensures the continuous documentation of the compliance of a specific package to the approved package design, comprising mainly records resulting from operation and surveillance. T2 - RAMTRANS 2024 CY - London, United Kingdom DA - 15.05.2024 KW - Radioactive Materials KW - Ageing Management KW - Transport Packages KW - Dual Purpose Casks PY - 2024 AN - OPUS4-60177 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GOVDOC A1 - Neumann, Martin T1 - Measures for quality and ageing management for non-competent authority approved package designs for the transport of radioactive material N2 - The BAM-GGR 016 explains the requirements of ADR, RID, ADN and IMDG for management systems for design, manufacturing, testing, documentation, use, maintenance, and inspection of packagings for package designs for the transport of radioactive material not requiring competent authority approval for all designs of exempted packages, packages type IP-1, IP-2, IP-3 and type A. KW - Not requiring competent authority approval KW - Radioactive material KW - Transport PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636506 VL - BAM-GGR 016 SP - 1 EP - 25 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin ET - Revision 1 AN - OPUS4-63650 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Komann, Steffen T1 - Fracture Mechanical Analyses of a Welding Seam of a Thick-Walled Transport Package N2 - Transport packages shall satisfy various safety criteria regarding mechanical, thermal and radiation phenomena. Typical requirements focusing mechanical aspects are usually drop tests in accordance with IAEA regulations [1]. The drop tests are usually carried out experimentally and, as an additional measure, finite element analyses (FEA) are performed. A specific part of the investigations presented is the evaluation of the welding seam connecting cask shell and cask bottom. Experimental results and FEA are presented and compared. The evaluation of the welding seam performed includes a variety of aspects. In addition to the experimental and analytical stresses determined, different standards are used to investigate a possible crack initiation. Several destructive and non-destructive tests are performed for quality assurance in the manufacturing process as well as for different input parameters. The necessary monitoring and non-destructive measurement methods to define the boundary conditions of the standards are introduced. Taking into account all required parameters, the welding seam is examined and evaluated using the failure assessment diagrams (FAD) of the respective standards. It can be shown under the given boundary conditions that considering the experimental data, the welding seam is in the context of crack initiation below the enveloping curve in the acceptable region. More critical drop tests to be conducted are proposed and need to be investigated in future work. T2 - Pressure Vessels & Piping Conference® 2022 CY - Las Vegas, NV, USA DA - 17.07.2022 KW - Drop test KW - Fracture initiation KW - Transport package PY - 2022 AN - OPUS4-55374 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Friction coefficients for wood-wood and wood-steel contacts N2 - The friction at the interfaces between pieces of wood and steel is of crucial importance for the impact and energy absorption in impact limiters of transport casks for radioactive material. Here, the friction coefficient for the combinations wood-wood and wood-steel was measured in the temperature range between -40°C and 90°C. Results show decreasing friction with increasing temperature, ranging from 0.43 at -40°C to 0.22 for 90°C for wood-steel combinations and from 0.3 at -40°C to 0.24 at 90°C for a wood-wood combination. T2 - Sandia-BAM Workshop CY - Berlin, Germany DA - 21.11.2022 KW - Wood KW - Friction KW - Transport cask PY - 2022 AN - OPUS4-56342 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Neumann, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Fracture Mechanical Analyses of a Welding Seam of a Thick-Walled Transport Package N2 - The safety demonstration of heavy weight type B transport packages used for storing spent nuclear fuel (SNF) or radioactive waste is ensured by a combination of physical testing and numerical calculations. While experiments are performed in accordance with the IAEA regulations for selected drop scenarios, Finite-Element-Method (FEM) simulations are used to predict the most damaging case and to investigate additional drop positions. BAM as competent authority in Germany has performed different investigations of a welding seam for a typical large transport package made of A508 forged steel, where the bottom plate is welded to the cylindrical shell. The package has a mass of approx. 120 t. Results of physical drop tests with a full-scale model and accompanying preliminary FEM simulations are presented to determine the decisive stresses in the welding seam. A drop test only represents one set of a package and test parameters. A further parameter analysis is considered to account for allowable variations of packaging properties (e.g. resulting from the manufacturing process) and, based on IAEA requirements, the temperature dependence of the material behaviour. The results of the stress analyses from the drop test and the simulation form the basis and provide the input parameters for a fracture mechanics analysis. In addition to the IAEA specifications, further standards are taken into account for an in-depth investigation, see R6, BS 7910 and API 579-1/ASME FFS1. All the above-mentioned standards require a manufacturer-specific defect analysis with respect to size and position. Both result from the welding process and the following heat treatment regime. The maximum defect sizes are ensured with non-destructive test methods (such as ultrasonic or particle methods) as integral part of the manufacturing process of the welding seam. Another important parameter in the welding process is the residual stress (secondary stress). The combination of the primary and secondary stress determines the total stress in the welding seam. The most damaging case of the welding seam is determined and evaluated with help of the above-mentioned standards and taking into account the IAEA requirements with respect to defect sizes, material properties, primary and residual stress, yield strength etc. T2 - PATRAM 22 - The International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-Les-Pins, Antibes, France DA - 11.06.2023 KW - Transport Package KW - Welding KW - Fracture Mechanics PY - 2023 SP - 1 EP - 10 AN - OPUS4-57696 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - Welding Seam Safety Evaluation in a Thick-Walled Type B Transport Package N2 - The safety demonstration of heavy weight type B transport packages used for storing spent nuclear fuel (SNF) or radioactive waste is ensured by a combination of physical testing and numerical calculations. While experiments are performed in accordance with the IAEA regulations for selected drop scenarios, Finite-Element-Method (FEM) simulations are used to predict the most damaging case and to investigate additional drop positions. BAM as competent authority in Germany has performed different investigations of a welding seam for a typical large transport package made of A508 forged steel, where the bottom plate is welded to the cylindrical shell. The package has a mass of approx. 120 t. Results of physical drop tests with a full-scale model and accompanying preliminary FEM simulations are presented to determine the decisive stresses in the welding seam. A drop test only represents one set of a package and test parameters. A further parameter analysis is considered to account for allowable variations of packaging properties (e.g. resulting from the manufacturing process) and, based on IAEA requirements, the temperature dependence of the material behaviour. The results of the stress analyses from the drop test and the simulation form the basis and provide the input parameters for a fracture mechanics analysis. In addition to the IAEA specifications, further standards are taken into account for an in-depth investigation, see R6 [1], BS 7910 [2] and API 579-1/ASME FFS1 [3]. All the above-mentioned standards require a manufacturer-specific defect analysis with respect to size and position. Both result from the welding process and the following heat treatment regime. The maximum defect sizes are ensured with non-destructive test methods (such as ultrasonic or particle methods) as integral part of the manufacturing process of the welding seam. Another important parameter in the welding process is the residual stress (secondary stress). The combination of the primary and secondary stress determines the total stress in the welding seam. The most damaging case of the welding seam is determined and evaluated with help of the above-mentioned standards and taking into account the IAEA requirements with respect to defect sizes, material properties, primary and residual stress, yield strength etc. T2 - PATRAM 22 - The International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Welding KW - Fracture Mechanics KW - Transport Package PY - 2023 AN - OPUS4-57695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Friction coefficients for wood-wood and wood-steel interfaces in impact limiters for transport casks N2 - Wood is widely used in impact limiters of transport casks for radioactive material. Encapsulated by an outer and inner steel structure, spruce wood is often applied in layers of alternating direction. The friction at the interfaces between these layers is of crucial importance for the impact and energy absorption e.g., at an accidental impact of a cask against a hard target. In order to get detailed information for corresponding numerical calculations, in this study the friction coefficient for the combinations wood-wood and wood-steel was measured in the temperature range between -40°C and 90°C according to the relevant stress conditions for such casks. Results show decreasing friction with increasing temperature, ranging from 0.43 at -40°C to 0.22 for 90°C for wood-steel combinations and from 0.3 at -40°C to 0.24 at 90°C to for a wood-wood combination. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-les-Pins, France DA - 11.06.2023 KW - Wood KW - Friction KW - Transport cask PY - 2023 AN - OPUS4-57702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen T1 - Ageing management measures for transport packages for radioactive materials N2 - The consideration of ageing mechanisms is with integration into the IAEA-requirements now obligatory for the design of transport packages. For packages intended to be used for shipment after storage the consideration of the effects of ageing mechanisms during storage in safety analyses and the implementation of corresponding instructions for operation and maintenance are required. Therefore, these packages have been maintained during storage in a manner that all requirements specified in the IAEA-requirements and in the applicable certificates of approval have been fulfilled. BAM is the competent authority in Germany for evaluating the thermal and mechanical design of packages for the transport of radioactive materials. In this context, BAM also evaluates the aging mechanisms and aging effects occurring during the long-term storage period of such transport packages. BAM has developed a guideline for the implementation of ageing assessment and of the measures for ageing management into the approval procedure based on IAEA-requirements. The goal of the presented paper is to introduce this guideline and the general approach for ageing management requirements and to describe the application to a specific package design. The type and amount of the ageing management not only depend on the use of the packaging, but also on the accessibility of the components that are considered in the ageing assessment. The different operating phases of a packaging are considered for the ageing assessment, such as loading, interim storage or transport. The implementation of measures for ageing management is divided into three levels – systemic measures, package design related measures and documentation. The systemic measures are attributed to the general management system and define the whole activities for organization of ageing management like structure, responsibilities, documentation, reports and evaluation. The package design related measures are defined in an ageing management plan (AMP). Therefore, an ageing surveillance program (ASP) and, if necessary, a gap analysis program has to be developed. The ageing management documentation (AMD) ensures the continuous documentation of the compliance of a specific package to the approved package design, comprising mainly records resulting from operation and surveillance. T2 - PVP2023-Pressure, Vessels & Piping Conference CY - Atlanta, GA, USA DA - 16.07.2023 KW - Radioaktive Stoffe KW - Transport KW - Gefahrgut PY - 2023 AN - OPUS4-58003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Feldkamp, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Transport of HLW canisters on sea vessels N2 - Germany had been transporting spent fuel to the reprocessing plant in Sellafield and La Hague for decades until around 2005. Resulting from the obligation to take back the vitrified high-level waste from reprocessing six CASTOR® HAW28M filled with 168 canisters with radioactive waste in vitrified form were transported from Sellafield to the interim storage facility Biblis in 2020. Rail wagons were used for the transport to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. BAM was involved in the authority assessment of the conditions for the sea transport. For the first transport BAM required among others, assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask in order to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of IMDG code and its supplement INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - RAMTrans 2024 CY - London, United Kingdom DA - 14.05.2024 KW - Transport KW - Spent nuclear fuel KW - Ship KW - Sea KW - High level waste PY - 2024 SP - 1 EP - 8 AN - OPUS4-60092 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Martin A1 - Gröke, Carsten A1 - Wille, Frank T1 - BAM-GGR 016 - Auf dem aktuelle Stand N2 - Die BAM-GGR 016 zur Anerkennung und Überwachung von Managementsystemen für nicht zulassungspflichtige Verssandstücke für radioaktive Stoffe wurde kürzliche erstmals revidiert. KW - BAM-GGR 016 KW - Überwachung KW - Anerkennung KW - Radioaktive Stoffe PY - 2024 SN - 0944-6117 IS - 5 SP - 11 EP - 13 PB - Verlag Heinrich Vogel CY - München AN - OPUS4-59998 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Transport of HLW canisters on sea vessels N2 - Germany had been transporting spent fuel to the reprocessing plant in Sellafield and La Hague for decades until around 2005. Resulting from the obligation to take back the vitrified high-level waste from reprocessing six CASTOR® HAW28M filled with 168 canisters with radioactive waste in vitrified form were transported from Sellafield to the interim storage facility Biblis in 2020. Rail wagons were used for the transport to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. BAM was involved in the authority assessment of the conditions for the sea transport. For the first transport BAM required among others, assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask in order to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of IMDG code and its supplement INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - RAMTrans 2024 CY - London, GB DA - 14.05.2024 KW - Transport KW - Spent nuclear fuel KW - Ship KW - Sea KW - High level waste PY - 2024 AN - OPUS4-60091 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias T1 - AI-Based Documentation Analysis for Safety Assessment of Packages for Radioactive Material N2 - The transportation of radioactive material requires, dependent on type und quantity of the radioactive material, a regulatory approval based on the type of the package. Safety assessments shall be conducted in compliance with the IAEA regulations and documented in a comprehensive package design safety report to obtain approval from authority. This comprehensive safety report evaluates a broad range of requirements from the regulations, including mechanical, thermal, shielding, criticality and transport requirements and controls, and testing assessments. Additionally, it encompasses supporting documents such as specifications, inspections, certifications, drawings, and guidelines in a variety of complex documents. Safety and manufacturing reports contain multiple interconnected sub-reports covering various topics. Changes, such as component modifications, material property updates, or regulatory revisions, often impact multiple sections of the safety analysis reports, making even minor adjustments complex and time-consuming. Each transport package has unique requirements, making every safety report distinct, despite following the same regulatory framework. Most documentation exists in standard digital formats but is often not machine interpretable. This lack of interpretability means individuals must manually identify and address dependencies within the reports. An AI-based documentation system that visualizes these dependencies would significantly enhance the efficiency of safety assessments. By linking interpretable content directly to datasheets, tables, simulations, experimental results, standards, and regulations, such a system would automatically identify changes and interdependencies. Related conditions could be validated using AI-based tools, reducing the need for manual intervention, improving both efficiency and safety. Human error plays a significant role in drafting, reviewing, and revising safety reports, often requiring iterative review cycles and multiple reviewers before approval. A digital quality infrastructure could reduce iterations and further improve efficiency. Integrating AI into this process could optimize safety assessments and enhance their robustness by leveraging interpretability to enhance safety. This preliminary study explores the readiness and requirements for using LLMs and RAG in the context of regulatory compliance for transport of radioactive material. By analyzing current documentation workflows, we identify how LLM-based tools can interpret complex safety reports and highlight critical interdependencies. We stress the importance of robust data governance, confidentiality measures, and AI reliability in this highly regulated context. T2 - BAM – Fraunhofer Materials LLM Days CY - Würzburg, Germany DA - 03.07.2025 KW - KI KW - RAG KW - LLM PY - 2025 AN - OPUS4-63727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -